Englander 10-CPM Guide d'installation

Catégorie
Poêles
Taper
Guide d'installation
INSTALLATION & OPERATION MANUAL
MODEL NUMBERS: 10-CPM 49-TRCPM 49-SHCPM
Thank you for purchasing this product from a fine line of heating equipment.
We wish you many years of safe heating pleasure with your new heating appliance.
Save These Instructions.
IMPORTANT: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO
THE DEALER. CONTACT TECHNICAL SUPPORT @ 1-800-245-6489.
Please Note the Following Precautionary Statements:
NOTE: WE DO NOT RECOMMEND PELLET/CORN/MULTI-FUEL STOVES AS YOUR ONLY SOURCE OF HEAT.
CAUTION: Please read this entire manual before installation and use of this
Pellet/Corn/Multi-fuel burning room heater.
Keep children, furniture, fixtures and all combustibles away from
any heating appliance.
WARNING: USE OF OUTSIDE AIR IS MANDATORY WITH THIS UNIT.
DO NOT OPERATE UNIT WITH HOPPER OPEN. LID MUST BE SHUT AND TIGHTLY SECURED.
DO NOT OPERATE WITH DOOR OPEN
SAFETY NOTICE
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH. FOR YOUR SAFETY AND PROTECTION, FOLLOW ALL THE
INSTALLATION INSTRUCTIONS. CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS FOR
RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS (INCLUDING PERMITS) IN
YOUR AREA.
Questions? Need Parts or Options? www.heatredefined.com
Rev. 5/2015
England’s Stove Works highly recommends the use of smoke detectors and
Carbon Monoxide detectors with any hearth product, including this unit. Follow all
manufacturers’ instructions when using smoke or Carbon Monoxide detectors.
Mobile Home Use:
These freestanding Pellet/Corn/Multi-fuel units are approved for mobile home or doublewide
installation with outside combustion air hook-up. See “Flue System” section of manual.
Mobile home installation should be in accordance with the Manufactured Home and Safety
Standard (HUD), CFR 3280, Part 24.
WARNING: Do Not Install in Sleeping Room.
CAUTION: The structural integrity of the mobile home floor, wall and ceiling/roof
m
ust
be
m
a
in
ta
in
ed
.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
2
A letter from our Technical Support department:
Thank you for purchasing this fine product from England’s Stove Works!
England's Stove Works was started, and is still owned by, a family that
believes strongly in a "Do It Yourself" spirit – that’s one reason you found
this product at your favorite “Do It Yourself” store.
We intentionally design and build our stoves so that any homeowner can
maintain his or her unit with basic tools, and we're always more than
happy to show you how to do the job as easily and as inexpensively as
possible.
From our free, downloadable service sheets; to our detailed Service
Videos; to our new "wizard-style," click-through Troubleshooting guide
on our web site, we have always tried to help our customers stay "heat-
ready," especially while oil and electricity prices continue to skyrocket.
Please look at our vast Help section on our web site and call our
Technical Support department at (800) 245-6489 if you need any help with
your unit. We are nearly always able to help “walk you through” any
repairs, problems or questions you may have.
PLEASE NOTE: While information obtained on our web site and through
our 800 number is always free of charge, there will be a service charge
incurred with any “on-site” repairs or maintenance that we may arrange.
Wishing you years of efficient, quality and “comfy” heating,
England’s Stove Works
Technical Support Department
www.heatredefined.com
(800) 245-6489
IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER.
CONTACT TECHNICAL SUPPORT at 1 (800) 245-6489.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
3
IMPORTANT INFORMATION
1. Installation of this Pellet/Corn/Multi-fuel unit should be performed by a professional only.
Check local installation codes for your area. Call your Homeowner’s Insurance
representative for inspection of your stove’s installation.
2. Read and comply with the instructions in this manual.
3. This unit should be tested (dry run) for 20 minutes before loading pellets or cherry pits. The
stove should automatically shut itself off after the 20-minute dry run. Corn is a 30-minute
cycle.
4. If burning pellets, you should use Premium Pellets, as this stove is designed for
Premium Pellets. Pellets with high ash content will burn dirty and require the unit to be
cleaned more often.
5. If burning corn, you should use corn with less than 14% moisture content. Corn with
high moisture content will burn dirty and require the unit to be cleaned more often.
6. If burning cherry pits, you should use cherry pits with less than 4% moisture
content. Cherry pits with high moisture content will burn dirty and require the unit to be
cleaned more often.
7. Be sure your corn, cherry pits or pellets are not damp or wet. If your fuel is too damp, this
stove may not be able to run on the lower Heat Range settings (the fire will die out). Be
sure to keep sawdust, debris and fines out of the unit.
8. Use three-inch (3”) U.L.-approved CORN VENT TWIST-LOCK PIPE when installing this
stove and follow the manufacturer’s specifications for installation and clearances (we highly
recommend Dura-Vent corn twist-lock pipe – our Part Number AC-33000). Even though
this pipe interlocks, it is recommended to seal all connections with high temperature
silicone (our Part Number AC-RTV3) or aluminum duct seal tape. Use at least three
screws to secure the pipe to this unit’s exhaust blower. Also, if you do not use U.L.-
approved twist-lock corn pipe, be sure to use U.L.-approved Corn Vent pipe, and fasten
each joint of the pipe with at least three screws.
9. Outside combustion air is mandatory for these units to work properly. Make this connection
using a 1
7
/
8
” I.D. metal pipe (steel, aluminum or copper) and coupler. Be sure to secure
the pipe to the unit with a clamp or aluminum tape. The outside end should be covered
(screened) to prevent any foreign matter from entering the system. Try to keep the number
of bends in this pipe to a minimum. Our Part Number PU-OAK (Outside Air Kit with flex
pipe) can be used.
NOTE: If the total run of the connection exceeds six feet (6’), use 3” metal pipe and
coupler instead.
10. Regularly inspect the burnpot area, remove the feeder pot and clean all plugged holes.
See Maintenance Section.
11. The ash in the burnpot should be removed regularly, depending on your burn rate. The
area to the right and left of the burnpot is for ash storage; keep the air holes in the burnpot
clean for a more efficient burn. Check your exhaust system frequently. Refer to “Ash
Removal and Disposal” section.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
4
12.
Keep corn, pellets and all other combustible materials a safe distance from the unit.
13. This unit will require floor protection if installed on a combustible surface. The minimum
floor protector for this unit is 36” x 48” which should give you at least six inches (6”) of
protection at the rear and at each side, and six inches (6”) minimum in the front of the unit.
14. Horizontal runs should not exceed four feet (4’) with a maximum vertical flue height of thirty
five feet (35’). At fifteen feet (15’), the pipe should be increased to four inch (4”) corn vent
pipe.
15. This unit should be turned off and allowed to cool prior to cleaning. Any ashes should be
kept in an airtight metal container and not disposed of until they are completely cooled.
16. Read the instructions thoroughly, including instructions concerning the digital control
board, and save them for future reference.
17. Do not allow paint, chemicals or construction dust on or near your unit. Do not allow liquid
or ANY foreign materials on or inside your unit. Shut your unit down and cover it when
painting, construction or similar activity is taking place. Wipe and clean your unit after any
construction is done in your home, or if any foreign material gets on or inside your unit.
You may also need to remove the rear and side cover plates to your unit (unplug unit first)
and vacuum and clean the motors and inside of your unit.
18. Improper gasket maintenance, including failure to replace gaskets, can cause air leaks
resulting in smoke-backs.
19. Remember that, as with any appliance, there is user responsibility involved, including
installation, operation and maintenance of this product. Be sure to check local codes, and
call Technical Support at (800) 245-6489 if you have any questions.
20. Be sure to follow the directions of all manufacturers of third party products that you
use, including exhaust pipe, etc. Never apply firestarter products (including gel) to a
hot surface or hot coals.
21. Basement Installation: Basement installation should be performed only by a professional
installer. For basement installations, a three inch (3”) pipe and coupler must be used for
Outside Combustion Air, and a minimum clearance of three feet (3’) must be maintained
from the ground to the corn vent exhaust pipe outside the dwelling. Keep in mind that each
elbow used reduces draft by up to 30%; it is good practice to add three feet (3’) of vertical
rise for each elbow used. Example: After the 2
nd
elbow used, add six feet (6’) of vertical
rise before terminating your vent pipe.
22. DANGER! Do not open the door on this unit if the Stirrer is still moving! See instructions
on “Setting the Stirrer” later in this manual. See burnpot installation pictures.
IMPORTANT NOTICE:
This unit must be properly installed to prevent the possibility of a house fire or “smoke-
back.” The instructions must be strictly adhered to.
Do not use makeshift methods or material which may compromise the installation.
Your unit requires periodic maintenance and cleaning (refer to manual). Failure to
maintain your unit may lead to a variety of problems, including but not limited to smoke
spillage into the home. England’s Stove Works will not be liable for consequential or
indirect damages to property or persons resulting from the use of this product.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
5
UNIT PREPARATION
1. Attach the spring handle to the door by turning it counterclockwise. Important: Also
check hopper latch – must be tight so that the top is sealed to prevent back-burn.
2. Test your 110-volt outlet for current and then plug in the unit. (Must be a 15A circuit
minimum, should be 20A if circuit is GFIC protected. We highly recommend a
surge protector for our unit, as the control panel is electronic).
3. Be sure to “dry run” your unit for 20 minutes before connecting it to the flue. During this
time the blowers and auger will operate at different times throughout the 20-minute
period (it should stop automatically after 20 minutes; 30 minutes for corn).
IMPORTANT INFORMATION – READ BEFORE OPERATING
When installing your Pellet/Corn/Multi-fuel stove, particular attention needs to be made in
regards to fire protection. If the unit is not properly installed, a house fire may result. For
your safety, follow the installation and operation instructions provided, and if a question
arises contact local building or fire officials about restrictions and installation
requirements in your area.
Read the Operation and Fuel sections of this manual before plugging in your unit.
Always unplug the unit before attempting any service work.
Do not connect the unit to a chimney flue already serving another appliance.
When installing the chimney pipe to the unit, it is important to remember that the unit
operates on negative pressure and the chimney on positive pressure. All chimney
connections, elbows, and fittings must be air-tight. (Proper venting practices must be
followed. Consult with a venting professional.)
Ashes must be disposed of in a metal container with a tight fitting lid.
All minimum clearances to combustibles must be followed.
It is important to use fuel that is clean, dry and consistent. It is recommended that
you purchase your entire heating season supply of fuel at one time, to make sure it is the
same.
This unit has been tested with 3 different fuels as of May 2007. Call Technical Support at
(800) 245 6489 if you have questions regarding the fuel you are trying to burn.
This stove was tested with:
1. Hardwood Pellets
2. Shelled Corn
3. Cherry Pits
Visit our web site at www.heatredefined.com for helpful information,
frequently asked questions, parts/accessory orders and more!
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
6
The Pellet/Corn/Multi-fuel stove is tested for operation with corn with 14% or less
moisture content; it is recommended that corn with 11-12% moisture be used for most
efficient operation of this unit. Corn with over 12% moisture has a lower BTU value
and will be hard to burn on the lower settings.
Corn must be clean and free from debris; never burn corn straight from the field. Stalk
parts, excessive fines and cob remnants, etc. will clog the auger mechanism. We highly
recommend the use of a sifter; sifters to filter your corn are available from dealers.
Damage caused by dirty and/or unfiltered (unsifted) corn is not covered by the product
warranty – ask for and use clean filtered bagged corn only.
DISCLAIMER NOTICE: No guarantee is made regarding the heating capacity of this
product. The actual area that this unit will heat depends on factors such as building
conditions, heat loss, type of construction, amount and type of insulation, type of air
movement and heat distribution, and the location of the product.
Important: Your home must be checked to verify that there is no negative pressure that
will affect the operation of this appliance.
IMPORTANT: DO NOT BURN “TREATED” SEED CORN IN YOUR STOVE. Seed corn
is treated with chemical pesticides that are harmful or fatal if swallowed; therefore, seed
corn is dangerous to have in the house, especially where children can reach it. Burning
treated seed corn in your stove will void your warranty and will destroy the exhaust
system on the unit.
There are many varieties of corn grown around the world. Each variety has unique
characteristics including the shape and size of the kernel. Your stove will burn more
consistently with a small to medium kernel corn. If the kernel size of the corn varies
greatly or if you switch sources frequently, you will get a less consistent burn. Do not use
corn with high wax content.
Vacuum the hopper out after every 6-8 bags to eliminate buildup of saw dust and fines
from corn.
Your unit was primarily designed to burn pellets, but will also burn dried cherry pits.
Make sure your supplier is selling Dried Cherry Pits (preferably with less than 4%
moisture content) for use as fuel in pellet burning stoves.
IMPORTANT: DO NOT USE CHERRY PITS DESIGNED FOR CRAFTS AND HOBBIES.
This type is usually bleached and/or over-dried.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
7
VENT TERMINATION CLEARANCES
A) MIN. 4-FT CLEARANCE BELOW OR BESIDE ANY DOOR OR WINDOW THAT OPENS.
B) MIN. 1-FT CLEARANCE ABOVE ANY DOOR OR WINDOW THAT OPENS.
C) MIN. 2-FT CLEARANCE FROM ANY ADJACENT BUILDING.
D) MIN. 7-FT CLEARANCE FROM ANY GRADE WHEN ADJACENT TO PUBLIC
WALKWAYS.
E) MIN. 2-FT CLEARANCE ABOVE ANY GRASS, PLANTS, OR OTHER COMBUSTIBLE
MATERIALS.
F) MIN. 3-FT CLEARANCE FROM A FORCED AIR INTAKE OF ANY APPLIANCE.
G) MIN. 2-FT CLEARANCE BELOW EAVES OR OVERHANG.
H) MIN. 1-FT CLEARANCE HORIZONTALLY FROM COMBUSTIBLE WALL.
I) VENTS INSTALLED WITH MECHANICAL EXHAUSTERS SHALL TERMINATE NOT LESS THAN 12 IN.
(305MM) ABOVE THE HIGHEST POINT WHERE THEY PASS THROUGH THE ROOF SURFACE.
Notes on termination of Pellet Vent Pipe from NFPA211(2006ed.)Section10.4Termination:10.4.5
(See also “INSTALLATION” section of manual AND additional notes above):
- Not less than three (3) feet above any forced air inlet located within ten (10) feet.
- Not less than four (4) feet below, four (4) feet horizontally from, or one (1) foot above any door, window
or gravity air inlet into any building.
- Not less than two (2) feet from an adjacent building, and not less than seven (7) feet above grade where
located adjacent to public walkways.
The exhaust exit shall be arranged so that the flue gases are not directed so that it will affect people, overheat
combustible structures, or enter buildings. Forced draft systems and all parts of induced draft systems under
positive pressure during operation shall be installed gastight or to prevent leakage of combustion products into a
building. Through-the-wall vents shall not terminate over public walkways, or where condensate or vapor could
create hazards or a nuisance.
Be sure to follow local codes and all manufacturer’s instructions (including exhaust pipe).
Consult a professional installer and/or call Technical Support if you have any questions.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
8
GUIDELINES FOR EXHAUST VENTING SYSTEMS DESIGN
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER
A UL listed three-inch or four-inch (3”or 4”) type “L” corn vent exhaust system must be
used for installation and attached to the pipe connector provided on the back of the unit.
Use a three-inch to four-inch (3” to 4”) adapter for four-inch (4”) pipe. A cap must be used
at the termination of type “L” vent chimneys. Four-inch (4”) type “L” is recommended for
elevations above 2,500 feet above sea level.
Do not terminate vent in any enclosed or semi-enclosed area, such as: carports, garage,
attic, crawl space, under a deck or porch, walkway or enclosed area, or any location that
could build up a concentration of fumes such as a stairwell, covered breezeway, etc.
Vent surfaces can get hot enough to cause burns if touched. Non-combustible shielding
or guards may be required.
Do not install a flue damper in the exhaust vent of this unit.
Termination must exhaust above air inlet elevation. Installation MUST include three (3)
vertical feet of corn vent pipe. This will create some natural draft to prevent the possibility
of smoke or odor during unit shutdown, and keep exhaust from causing a nuisance or
hazard from exposing people or shrubs to high temperatures. DO NOT CONNECT THIS
UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE. DO NOT CONNECT
DIRECTLY TO A MASONRY CHIMNEY.
Distance from doors and windows, gravity or ventilation air inlet into building: not less
than four feet (4 ft.) below, four feet (4 ft.) horizontally from, one foot (1 ft.) above (this
does not apply if the windows are non-opening or have been fixed so they cannot open).
Distance from bottom of termination and grade - three feet (3 ft.) minimum. This is
conditional upon the plants and nature of the grade surface. The exhaust gases are hot
enough to ignite grass, plants, shrubs, etc. located in the vicinity of the termination. The
grade must not be a lawn. Distance from bottom of termination and public walkways is
seven feet (7 ft.) minimum.
Distance to combustible materials – three feet (3 ft.). This includes adjacent buildings,
fences, protruding parts of the structure, roof overhang, plants and shrubs, etc.
The installation must include a cleanout tee to enable the collection of fly ash and permit
periodic cleaning of the exhaust system. 90° elbows accumulate fly ash and soot,
thereby reducing exhaust flow and performance of the unit. Each elbow or tee reduces
draft potential by up to 30%.
NOTE: YOUR UNIT MUST BE INSTALLED BY A QUALIFIED
INSTALLER, SUCH AS AN NFI CERTIFIED SPECIALIST
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
9
Total length of horizontal vent must not exceed 48” (4 ft.). Use three-inch (3”) U.L.-
approved CORN VENT TWIST-LOCK PIPE when installing this stove and follow the
manufacturer’s specifications for installation and clearances (we highly recommend Dura-
Vent corn twist-lock pipe – our Part Number AC-33000). Even though this pipe interlocks,
it is recommended to seal all connections with high temperature silicone (our Part Number
AC-RTV3) or aluminum duct seal tape. Use at least three screws to secure the pipe to this
unit’s exhaust blower. Also, if you do not use U.L.-approved twist-lock corn pipe, be sure to
use U.L.-approved Corn Vent pipe, and fasten each joint of the pipe with at least three
screws.
The “L” vent or corn vent stainless exhaust system must be installed so as to be GAS
TIGHT! Follow the vent manufacturer’s installation instructions.
The area where the vent pipe penetrates the exterior of the home must be sealed with
silicone or other means to maintain the vapor barrier between the exterior and the interior
of the home.
NOTE: These are guidelines only. Proper venting is accomplished by design and
common sense. In most installations, three-inch (3”) diameter venting is
adequate. If it does not vent properly, you must change it to four-inch (4”)
diameter venting.
DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
10
BURNING SOLID FUELS
Ashes will need to be removed from the unit periodically. See Ash Removal section. You can
minimize cleaning required and maximize efficiency by maintaining the proper draft.
This unit has been designed to burn premium pellets, dry shelled corn or dried cherry pits that meet
the Pellet Fuels Institute (PFI) standards.
WOOD PELLETS
Be consistent in your choice of wood pellet supplier. Pellets will vary in content and burn
characteristics from supplier to supplier.
Check your pellets for foreign objects. Your stove warranty will not cover any damage caused
due to foreign objects in the fuel supply.
Store your pellets in a dry place to prevent them from absorbing added moisture.
To decrease sawdust buildup, the hopper will need to be vacuumed out after every 6-8 bags of
pellets, or more often if the quality of the pellets is poor. You may need to screen each bag of
pellets if the sawdust becomes a problem.
Wood pellets vary in size and also ash content (from less than 1% to 3% or more). Your unit will
burn more efficiently with small to mid-size pellets. Low ash content pellets will allow you to burn
the stove longer between cleanings.
Your unit is designed to burn pellets that are no larger than one-quarter inch (¼”) in diameter,
and no longer than two and one-half inches (2 ½”) long.
CAUTION: DO NOT PLACE SUCH FUELS WITHIN THE SPACE HEATER’S INSTALLATION
CLEARANCES OR WITHIN THE SPACE REQUIRED FOR CLEANING AND ASH
REMOVAL.
SHELLED CORN
(Dry, preferably with 11-12% moisture content)
Never burn “deer corn” as it frequently contains molasses/sugars. Store your corn supply in a dry
place and keep bags or container sealed to prevent your corn from absorbing excess moisture. Test
the moisture content regularly to ensure proper dryness.
IMPORTANT: DO NOT BURN “TREATED” SEED CORN IN YOUR STOVE. Seed corn is treated
with chemical pesticides that are harmful or fatal if swallowed; therefore, seed corn is
dangerous to have in the house, especially where children can reach it. Burning
treated seed corn in your stove will void your warranty and will destroy the
exhaust system on the unit.
CHERRY PITS
(Dry, preferably with less than 4% moisture content)
Your unit was primarily designed to burn pellets, but will also burn dried cherry pits. Make sure
your supplier is selling Dried Cherry Pits for use as fuel in pellet burning stoves.
IMPORTANT: DO NOT use cherry pits designed for crafts or hobbies.
This type is usually bleached or over-dried.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
11
FLUE SYSTEM
Caution: Follow the pipe manufacturer’s installation instructions and directions for passing
through combustible walls and ceilings.
Be sure to check local codes in your area.
NOTE: See the installation drawing later in this manual (Illustration 1).
This unit is equipped with a negative draft system that pulls combustion air through the
burnpot and pushes the exhaust air out of the dwelling. If this unit is connected to the flue
system other than the way explained in this manual, it will not function properly. For any of
these installations, keep in mind that each elbow used reduces draft by up to 30%; it is good practice
to add three feet (3’) of vertical rise for each elbow used. Example: After the 2
nd
elbow used, add
six feet (6’) of vertical rise before terminating your vent pipe.
Corn Vent Pipe
The UL approved corn vent pipe that we recommend is a twist lock system; however, it is still
recommended that high temperature silicone (our Part Number AC-RTV3)
or aluminum duct seal
tape be used at each joint. England’s Stove Works recommends the use of Dura-Vent twist-lock
pipe (if you use other pipe, consult your local building codes and/or building inspectors, and secure
each joint with at least three screws—see “Important Information” section). Do not use “B” vent gas
pipe or galvanized pipe with this unit. The corn pipe is designed to disassemble for cleaning and
should be checked several times during the burning season — corn vent pipe is not furnished with
the unit and must be purchased separately. Do not install a flue damper of any kind in this
system, and do not connect this unit to a flue system serving another heating appliance.
Through the Wall
To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the
exhaust adapter is at least eighteen inches (18”) above ground level, a straight section of corn pipe
can be used to initially pass through the wall (see Illustration 1). Your dealer or our factory should be
able to provide you with a kit that will handle most of this installation, which will include a wall thimble
that will allow the proper clearances through a combustible wall. Once outside the structure, a three-
inch (3”) clearance should be maintained to the outside wall and a clean out tee should be placed on
the pipe that extends through the wall. We recommend a minimum of three feet (3’) of vertical pipe
with a 90-degree turn away from the house. At this point, a one-foot (1’) section and horizontal cap
will complete the installation (see Illustration 1).
A wall strap should be placed just below the last 90-degree section to make the system more
stable. If you live in an area that has heavy snowfall, it is recommended the installation be taller than
three feet (3’) to get above the snowdrift line.
The same type installation can be used if your stove is below ground level by adding the clean-
out section and vertical pipe inside until ground level is reached. However, we recommend
basement installation be performed only by a professional installer. For basement installations, a 3”
(three inch) pipe and coupler must be used for Outside Combustion Air, and a minimum clearance of
three feet (3’) must be maintained outside the dwelling from the ground to the Corn Vent Exhaust
Pipe.
Call (800) 516-3636 to inquire about the AC-33000 Through-the-Wall Kit or
Visit our web site at
www.heatredefined.com for ordering information!
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
12
The through-the-wall installation is the least expensive and simplest installation. In a through-
the-wall installation you should be mindful of the snowdrift line, as well as dead grass and leaves.
We recommend a three foot (3’) minimum vertical rise on the inside or the outside of the dwelling.
Through the Ceiling
When venting the stove through the ceiling, the pipe is connected the same as through the wall,
except the clean out tee is always on the inside of the house, and a 3” adapter is added before the
clean-out tee. You must use the proper ceiling support flanges and roof flashing supplied by the pipe
manufacturer -- follow the pipe manufacturer’s directions and Illustration 1 in this manual. It is
important to note that if your vertical runs of pipe are more than fifteen feet (15’) at this point, the corn
vent pipe should be increased to four inches (4”) in diameter. Do not exceed four feet (4’) of pipe on
a horizontal run, and do attempt to use the least number of elbows in the flue system. If an offset is
used it is better to install a 45-degree elbow whenever possible. Please remember, installing elbows
may inhibit your draft by up to 30% per elbow.
Outside Air (Outside Combustion Air Intake)
Outside air is mandatory for this unit to operate properly. This unit has been designed and tested
with this connection, because so many homes are airtight and there is not adequate combustion air
available inside the dwelling. The air intake pipe is located on the bottom side of the burnpot (from
the rear) and measures 1 ½” inside diameter (I.D.). The connection can be made with a metal 1
7
/
8
I.D. coupler and pipe (see “Important Information” section of manual), and should exit through the
wall. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end of the
pipe should be covered (screened) to prevent foreign matter from entering the system.
Our Outside
Air Kit (Part Number PU-OAK) can be used.
If the unit is located below ground level, you will need to
run the pipe up and then outside the dwelling. NOTE: If the total run of the connection exceeds six
feet (6’), if more than two elbows are used, or if a basement installation, use 3” metal pipe (and
coupler) instead.
Mobile Home Installation
Secure the heater to the floor using the two holes in the pedestal. If the unit is on a combustible
surface, you will need to drill matching holes in the floor protection that you choose (see Floor
Protection section). Do not disturb the structural integrity of the home, and be sure the unit is
permanently electrically grounded to the chassis of your home. Remember that outside combustion
air is mandatory, and not to install the unit in a sleeping room of the home.
Important Notes Concerning Installation:
IMPORTANT: Improper hook-up (too much pipe, too many elbows, etc.) will cause
the unit not to operate. Call Technical Support (800-245-6489) if you
have questions about your hook-up or if your unit will not operate.
IMPORTANT SAFETY NOTE: If the unit or chimney connector pipe “glows” red (or white), the stove
is over-fired. This condition could cause a house or chimney fire. Do
not operate your unit too hot, or over-firing may result.
*IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage
caused by the malfunction of a stove due to improper venting
or installation.
Call 800-245-6489 and/or consult a professional installer if you have any questions.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
13
FLOOR AND WALL PROTECTION
Floor Protection
If your floor is constructed of a non-combustible material such as brick or concrete, there is no need for
floor protection. If the floor is constructed of a combustible material such as hardwood, linoleum, or carpet, then
you will be required to use floor protection between the unit and the combustible. The protection should be U.L.
approved or equal, and should be large enough to provide a minimum of six inches (6”) behind and on both
sides of the stove. The clearance in front of the stove should be at least six inches (6”). This freestanding pellet
unit will need a minimum 36” x 48” floor protector.
Wall Protection
From the rear of this stove only six inches (6”) of clearance is required to paneling, wallpaper or drywall
(we recommend more clearance for maintenance access). Six inches (6”) would be required to a sidewall.
From the corner of the stove, 4 ½” of clearance is required. Alcoves: The alcove must be a minimum of sixty-
six inches (66”) from floor to ceiling. Six inches (6”) of clearance is required from the stove to an alcove
sidewall; six inches (6”) is required to an alcove back wall.
The corn vent pipe would require the standard three inches (3”) clearance, or as recommended by the pipe
manufacturer. Normally, additional wall protection is not required with this type unit.
Illustration 1
Freestanding Pellet/Corn/Multi-fuel Installation
Caution: Follow the pipe manufacturer’s installation instructions and directions for
passing through combustible walls and ceilings. Check local codes in your area.
Our Part AC-33000
is acceptable for
through-the-wall
installation.
(We recommend 4”
for 2500+ ft.
installations, Our
Part AC-33100.
)
Must have
minimum 3”
adapter before tee
for longer run.
For shorter run, tee
alone is acceptable.
Basement Installation
should be performed by
professional installer. Use
3” metal pipe and coupler
for Outside Combustion
Air. Minimum 3 ft. (3’)
clearance from ground to
the Corn Vent Exhaust
Pipe.
1. If 3” flue pipe exceeds 15’ in length, increase to 4” flue pipe for remaining flue connections.
2. Total flue length should not exceed 35’.
3. Horizontal run not to exceed 4’.
4. Floor protector required: Min. size 36” x 48”.
5. If the total run of outside air connection exceeds 6’, if more than 2 elbows are used, or if a
basement install, use 3” metal pipe (and coupler) instead.
6. Outside Air is mandator
y
f
or
p
ro
p
er sa
f
e o
p
eration.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
14
OPERATING INSTRUCTIONS
CAUTION: DO NOT OPERATE WITH THE DOOR OPEN.
Do not burn trash (paper bags, etc.) in this unit.
This stove has an induced draft system and is designed to operate continuously, as frequent
shutdown is not required. The setting of the “Heat Range” touch pad will control the heat output
and the amount of fuel the unit will burn (see “Control Board” section).
NOTE: This stove is using solid fuel and will not restart automatically unless a thermostat is
installed. See page 26 – Thermostat instructions.
* NOTE: Blower Speed will automatically be adjusted to the desired Heat Range that you select.
START- UP PROCEDURES
SETTING THE STIRRER
Warning: Do not open the door on this unit if the Stirrer is still moving!
Bodily Injury can occur!
The stirrer must be “set” before each burn so that the 4-prong side of the stirrer is pointing
straight up (see diagram below). To rotate the Stirrer, press and hold the “AIR ON TEMP” (i.e. “Air
On”) button (on the bottom of the Control Panel); it will stop rotating when you release the button.
To turn Stirrer Off and On: The Stirrer may be turned Off by pushing the “Air On” button on the
bottom of the Control Panel, and then pressing both Down arrows on the “Blower Speed” and “Heat
Range” until you see a “0” in the Blower Speed window. The Stirrer may be turned back On by
pressing the “Air On” button on the bottom of the Control Panel, and then pressing both Up arrows
on the “Blower Speed” and “Heat Range” until you see a “1” in the Blower Speed window.
CAUTION: Never use gasoline, lantern fuel, kerosene, charcoal lighter fluid, diesel fuel or
any other flammable liquid to start the fire. Keep all combustible materials at a
safe distance from stove.
The Heat Range and Blower Speed will automatically be set to setting “5” (default setting during
start up) to ensure that proof of fire is detected. During the 20 minute start-up period the user can set
the controls to a desired heat setting and after the 20 minute start-up the unit will operate at that user
setting. When burning corn, start-up period is 30 minutes.
Stirrer
Ill
ustration
2
This prong must be in the upright
position when restarting the stove
(the 4-prong side is in 12:00 position)
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
15
WARNING!
For pellets and corn, when the “Air On” button on the bottom of the Control Board is pressed, you
must make sure you see the number 1in the Blower Speed window. The Stirrer must be running in
the pellet and corn modes (mode 1 – pellet; mode 5 – corn, see Fuel Change Procedure, page 16). (As
previously stated, the Stirrer will stop if you press the “Air On” button and press the Blower Speed and
Heat Range arrows down until you see a zero (0) in the window. Before you restart your unit you must
see the number 1in the Blower Speed window - see previous page).
Make sure the Stirrer is turning before you walk away from the unit. The Stirrer will start 4 minutes into
the startup mode. It turns very slowly, so you will want to observe it to make sure it is actually moving!
NOTE: On the “first fire” (the first time you burn the unit), the Control Panel should be set at a “5” Heat Range
and “5” Blower Speed for at least 3 hours to allow the unit to “cure” as the oils from the manufacturing
process burn off. Windows and doors in the home should be opened to help ventilate as these oils
burn off.
NOTE: If the unit does not start, DO NOT try to restart the unit until it has cooled completely down. If the unit
does not start or maintain a fire, you will receive an E-2 in the Heat Range and Blower Speed window
of the Control Board. If this occurs, wait until unit has cooled completely down and repeat these
steps.
NOTE: The burnpot and Stirrer are part of a floating system. This means you will see it rise up and go down.
The unit is designed to burn multi-fuel; this feature will allow the unit to run and not hang-up or lock-
up on a hard piece of corn, etc. It may make a “jumping” noise when you first start the unit, but it will
go away after your unit heats up. It will not harm the unit. It is a heavy duty system made with
stainless steel, designed to last many trouble-free years.
FUEL NOT FEEDING CORRECTLY
If the fuel is not feeding correctly, the feed auger could possibly be misaligned due to factors such as rough
handling during shipping. If you suspect your feed auger is misaligned, call Technical Support at (800) 245-
6489.
Automatic Start-Up
When the “ON” button is pressed from a cold start, the unit is in “Start-Up” (after 3 seconds, there will be an
S U” in the Heat Range and Blower Speed windows to verify this). While in this mode, the unit has a preset
heat range and will remain in this mode for 20 minutes (30 minutes in corn mode) to prevent the unit from over-
firing. During this start-up period you can set the Control Board at the setting you desire; after the start-up is
complete, the unit will operate at the user setting.
Manually Starting Your Unit
In the event the Auto-Start does not initiate, you may manually start your unit. To manually start your unit,
first clean any pellets out of the burnpot (to prevent over-feeding). Place a handful of new pellets in the
burnpot, then spread a small amount of pellet fire starter over the pellets and ignite them. After the pellets
ignite, close the door to your unit and press the “ON” button (if the door is closed before the pellets fully ignite,
the Exhaust Blower could put out the fire).
Recommended fire starter materials are: Wax-impregnated wood chips, cardboard cubes or firestarter
chips designed for pellet and corn burning stoves. Follow any manufacturer’s directions for these products,
and NEVER place any firestarter on any hot surface or hot coals.
CAUTION: Never use gasoline, lantern fuel, kerosene, charcoal lighter fluid, diesel fuel or any other
flammable liquid to start the fire. Keep all combustible materials at a safe distance from
stove.
Wet corn may not start with your auto start igniter. It will help to keep a bag of pellets handy. If your corn
does not ignite, shut the unit down, clean out the burnpot and make sure the unit is not warm. Place a cup full
of wood pellets in the in the burnpot, place a small amount of one of the recommended fire starters (listed
above) on the wood pellets and ignite the pellets. Allow the pellets to burn for 1-2 minutes then close the door
and push the “ON” button.
CAUTION: The Firebox should be cool to the touch before attempting to start the unit.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
16
NOTE
If the unit does not start or maintain a fire, you will receive an E-2 in the Heat Range and Blower
Speed window of the Control Board. If this occurs, wait until unit has cooled completely down and
repeat.
To remove the Stirrer for cleaning
While the unit is COLD and the unit is off, press and hold the “AIR ON TEMP” (i.e. “Air On”)
button until the Stirrer is at the “12:00” position (with the 4 prongs pointing up). Pull the hitch pin
(marked in Illustration 3). Lifting the burnpot and Stirrer at the same time, remove the Stirrer from the
burnpot. Clean and clear all holes in the burnpot and replace Stirrer and burnpot back into the unit.
NOTE: When replacing the burnpot, notice there is a welded piece that is always set toward the
back of the Firebox. Also, be sure to replace the hitch pin.
Illustration 3
Locking
Collar
Illustration 4
Hitch Pin
Hitch Pin
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
17
FUEL CHANGE PROCEDURE
When starting the stove with corn, push the “AIR ON TEMP” button and hold, which will rotate the
Stirrer mechanism in the burnpot. Release the button when the 4-prong side of the Stirrer is straight
up (in the “12:00” position, as shown in Illustration 2, page 13). Then follow the previous instructions
concerning placing the handful of pellets in the burnpot and starting your fire (Manually Starting Your
Unit, page 14).
Changing from Pellets to Corn
Your unit was primarily designed to burn pellets, but will also burn corn. Your unit comes ready to
burn pellets by default; if you would like to burn corn in your unit, follow the steps below.
WARNING: Do not open the door on this unit if the Stirrer is still moving!
See instructions “Setting the Stirrer” on page 13 in this manual.
NOTE: Before performing these steps make sure the unit is out and completely cold!!
1. The control board must be reset to burn corn. Unplug the unit and plug back in, then press
the Blower Speed up and down buttons at the same time and release. You should see a “1
through 8” in the Heat Range window. Push the Heat Range up arrow until you see a “5.”
Wait for the window to clear. You are now set to burn corn. To change the stove back to
burn pellets: Push the Heat Range down arrow until you see a “1.” Wait for the window to
clear. You are now set to burn pellets.
2. Follow lighting instructions.
Changing from Pellets to Cherry Pits
Your unit was primarily designed to burn pellets, but will also burn dried cherry pits. Make sure
your supplier is selling Dried Cherry Pits for use as fuel in pellet burning stoves. Do not use cherry
pits designed for crafts or hobbies, as this type is usually bleached or over-dried. Your unit comes
ready to burn pellets by default; if you would like to burn cherry pits in your unit, follow the steps
below.
WARNING: Do not open the door on this unit if the Stirrer is still moving!
See instructions “Setting the Stirrer” on page 13 in this manual.
NOTE: Before performing these steps make sure the unit is out and completely cold!!
1. Remove the Stirrer shaft (See Illustrations 3 & 4 - Page 15). Do not use the Stirrer when
burning cherry pits.
2. The control board must be reset to burn cherry pits. Unplug the unit and plug back in, then
press the Blower Speed up and down buttons at the same time and release. Push the Heat
Range up arrow until you see a “6.” Wait for the window to clear. Remember to remove the
Stirrer (page 15). Set Air On button to “0” (see page 14 – first paragraph). You are now set
to burn cherry pits. To change the stove back to burn corn: Push the Heat Range down
arrow until you see a “5.” Wait for the window to clear. You are now set to burn corn. To
change the stove back to burn pellets: Push the Heat Range down arrow until you see a
“1.” Wait for the window to clear. You are now set to burn pellets. Remember to replace the
stirrer and set it to run when burning pellets and corn (see Setting the Stirrer, page 13).
3. Follow lighting instructions.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
18
E-Codes
“E-Codes,” or Error Codes, are codes that will appear in the Heat Range and Blower Speed
windows of the Control Board if your unit experiences problems. If you receive these codes,
wait until the unit is cooled completely down before trying to restart your unit.
If the unit continues to display any E-Code(s), please contact Technical Support at
(800) 245-6489 before further attempting to restart your unit.
NOTE: “E-0” indicates “No Error”
E-2 = Fail to Start
E-3 = Unit Overfired
If you see the E-3 code displayed on your control board, you have overfired your
unit. You must let the unit cool and clean the Firebox and burnpot. Be sure to
clean the orifices (holes in the burnpot). You should not burn your unit on High
(Heat Range 9) continuously when burning corn. After a couple of hours of burning
corn on high, turn the Heat Range to 7 and the Blower Speed to 9. WARNING:
Running the unit on high, when burning corn for long periods, can damage
the unit.
OPERATIONAL NOTES
First Fire: When you push the “ON” button, the Control Board will automatically be set at both
“Heat Range” and “Blower Speed” to setting “5.” Allow the stove to burn in this
manner for at least three (3) hours. This will allow the unit to “cure out” as the paint
and the oils from the manufacturing process burn off. We recommend you open
doors and windows in your dwelling during this process.
Subsequent Cold Starts: In a cold start situation, the unit should be operated at a “5”
setting until the room air blower begins to operate.
IMPORTANT NOTES:
- Please be patient. Your unit has a large burnpot and it takes awhile to
equalize (reach maximum heat levels). Do not be concerned by the size of
the flame, as this unit gets much hotter than the flame appears.
- Use gloves when filling the hopper.
- If you leave the hopper open too long, the stove will shut down.
NOTE: Press the “ON” button only once on start-up Except when the hopper is empty
(when you run out of fuel, or for your first fire, see above), press and hold the “ON”
button for 10 seconds to purge the unit. Pressing the “ON” button a second time
during the start-up cycle will cause the start-up cycle to begin again.
IMPORTANT: If the unit fails to start properly, or does not properly complete the Shut-Down
procedure, open the closest outside door and a window to eliminate the
home’s natural draft BEFORE opening the stove’s door or hopper lid. This
will allow any smoke to exit through the external air hook-up instead of spilling
into the home.
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
19
SHUT-DOWN PROCEDURE
WARNING: NEVER SHUT DOWN THIS UNIT BY UNPLUGGING IT
FROM THE POWER SOURCE.
Refer to the following instructions:
Press the “OFF” touch pad to put the stove in the “Shut-Down” mode. There will be an
S D in the Heat Range and Blower Speed windows while the unit is shutting down to verify
this. At this time the red light above the “OFF” pad will illuminate. When the “OFF” pad is
touched the auger will instantly stop feeding fuel to the auger tube, but the room air blower,
exhaust blower and Stirrer will continue to operate. When the internal temperature drops to
95 degrees the room air blower will cease to operate, and when the internal temperature
drops to 90 degrees the exhaust blower will stop. The red light will then shut off and the
entire stove will be shut down. The hotter the unit is operating, the longer it will take for the
stove to complete the Shut-Down cycle.
Note: The unit will exit the Shut-Down cycle if you press the “ON” button during Shut-
Down.
NOTE: If your unit overheats, the auger will stop feeding, "E3" will be displayed on
the control board and the unit will go into Shut-Down. If this happens you need
to wait 45 minutes before trying to re-light the unit.
If you have any questions or problems contact the Technical Support Department:
Technical Support Department [email protected]
P.O. Box 206 Parts Orders ONLY: 800-516-3636
Monroe, VA 24574 Questions: 800-245-6489 (Fax: 434-929-4810)
You may also order parts and options, view frequently asked questions and more, on our
Web Site:
www.heatredefined.com
IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING
CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.
ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE
TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.
20
DAILY OPERATION
Refueling the Unit
Always press the “OFF” touch pad before refueling. The hopper on this stove holds
approximately 50-lbs. (wood pellets), and should be refilled when the fuel level drops to three or four
inches.
Note: The hopper lid will be warm; therefore, you should always use some type of hand protection.
NEVER place your hand near the auger while the stove is operating.
Note: Always ensure that all corn and pellet matter is cleared from the hopper lid gasket before
closing. Be sure to close and latch hopper securely before re-firing. Do not operate this
unit with the hopper lid open or unsecured.
Power Outage
If the power to the unit is interrupted for approximately three minutes or less, the unit will resume
operation when power is restored according to the following table:
Unit’s State Before Power Loss State When Power Returns
ON Start-Up
Start-Up Start-Up
Shut-Down Shut-Down
OFF OFF
If the power is interrupted for more than (approximately) three minutes, the unit will be “OFF”
when power returns.
Important: Do NOT open the hopper lid or the door to the unit during power outage. Open
the closest outside door and a window to eliminate the home’s natural draft. Wait
for power to be restored and then press the “ON” button to re-start the unit, if desired.
Remember:
1) It is very important for the unit to be vented properly (see instructions on Outside Air),
as the natural draft is needed to clear the smoke from the stove.
2) Do not open the hopper lid (or the unit’s door). This may cause fire to burn in the
hopper.
Fuel Outage
If your unit runs out of fuel, let the unit go through the complete Shut-Down cycle and then follow
the instructions for restarting the unit.
NOTE: DO NOT TRY TO RESTART THE UNIT HOT. If the unit runs without pellets or corn,
after one hour the unit will shut down.
Combustion Blower Failure
If the Combustion (exhaust) Blower should fail on this unit, a Vacuum Shut-Down Switch will
automatically stop the auger. This will cause your stove to stop feeding fuel to the burnpot, and the
unit will eventually stop completely. Check your power supply, including tripped breakers, etc. If the
blower has failed, you will need to contact Technical Support at (800) 245-6489.
NOTE: It is very important for the unit to be vented properly (see instructions on Outside Air), as the
natural draft is needed to clear the smoke from the stove.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78

Englander 10-CPM Guide d'installation

Catégorie
Poêles
Taper
Guide d'installation

dans d''autres langues