Englander 10-CPM Guide d'installation

INSTALLATION & OPERATION MANUAL

MODEL NUMBERS: 10-CPM 49-TRCPM 49-SHCPM

Thank you for purchasing this product from a fine line of heating equipment.

We wish you many years of safe heating pleasure with your new heating appliance.

Save These Instructions.

IMPORTANT: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO

THE DEALER. CONTACT TECHNICAL SUPPORT @ 1-800-245-6489.

Please Note the Following Precautionary Statements:

NOTE: WE DO NOT RECOMMEND PELLET/CORN/MULTI-FUEL STOVES AS YOUR ONLY SOURCE OF HEAT.

CAUTION: Please read this entire manual before installation and use of this

Pellet/Corn/Multi-fuel burning room heater.

Keep children, furniture, fixtures and all combustibles away from

any heating appliance.

WARNING: USE OF OUTSIDE AIR IS MANDATORY WITH THIS UNIT.

DO NOT OPERATE UNIT WITH HOPPER OPEN. LID MUST BE SHUT AND TIGHTLY SECURED.

DO NOT OPERATE WITH DOOR OPEN

SAFETY NOTICE

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,

BODILY INJURY OR EVEN DEATH. FOR YOUR SAFETY AND PROTECTION, FOLLOW ALL THE

INSTALLATION INSTRUCTIONS. CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS FOR

RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS (INCLUDING PERMITS) IN

YOUR AREA.

Questions? Need Parts or Options? www.heatredefined.com

Rev. 5/2015

England’s Stove Works highly recommends the use of smoke detectors and

Carbon Monoxide detectors with any hearth product, including this unit. Follow all

manufacturers’ instructions when using smoke or Carbon Monoxide detectors.

Mobile Home Use:

These freestanding Pellet/Corn/Multi-fuel units are approved for mobile home or doublewide

installation with outside combustion air hook-up. See “Flue System” section of manual.

Mobile home installation should be in accordance with the Manufactured Home and Safety

Standard (HUD), CFR 3280, Part 24.

WARNING: Do Not Install in Sleeping Room.

CAUTION: The structural integrity of the mobile home floor, wall and ceiling/roof

m

ust

be

m

a

in

ta

in

ed

.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

2

A letter from our Technical Support department:

Thank you for purchasing this fine product from England’s Stove Works!

England's Stove Works was started, and is still owned by, a family that

believes strongly in a "Do It Yourself" spirit – that’s one reason you found

this product at your favorite “Do It Yourself” store.

We intentionally design and build our stoves so that any homeowner can

maintain his or her unit with basic tools, and we're always more than

happy to show you how to do the job as easily and as inexpensively as

possible.

From our free, downloadable service sheets; to our detailed Service

Videos; to our new "wizard-style," click-through Troubleshooting guide

on our web site, we have always tried to help our customers stay "heat-

ready," especially while oil and electricity prices continue to skyrocket.

Please look at our vast Help section on our web site and call our

Technical Support department at (800) 245-6489 if you need any help with

your unit. We are nearly always able to help “walk you through” any

repairs, problems or questions you may have.

PLEASE NOTE: While information obtained on our web site and through

our 800 number is always free of charge, there will be a service charge

incurred with any “on-site” repairs or maintenance that we may arrange.

Wishing you years of efficient, quality and “comfy” heating,

England’s Stove Works

Technical Support Department

www.heatredefined.com

(800) 245-6489

IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER.

CONTACT TECHNICAL SUPPORT at 1 (800) 245-6489.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

3

IMPORTANT INFORMATION

1. Installation of this Pellet/Corn/Multi-fuel unit should be performed by a professional only.

Check local installation codes for your area. Call your Homeowner’s Insurance

representative for inspection of your stove’s installation.

2. Read and comply with the instructions in this manual.

3. This unit should be tested (dry run) for 20 minutes before loading pellets or cherry pits. The

stove should automatically shut itself off after the 20-minute dry run. Corn is a 30-minute

cycle.

4. If burning pellets, you should use Premium Pellets, as this stove is designed for

Premium Pellets. Pellets with high ash content will burn dirty and require the unit to be

cleaned more often.

5. If burning corn, you should use corn with less than 14% moisture content. Corn with

high moisture content will burn dirty and require the unit to be cleaned more often.

6. If burning cherry pits, you should use cherry pits with less than 4% moisture

content. Cherry pits with high moisture content will burn dirty and require the unit to be

cleaned more often.

7. Be sure your corn, cherry pits or pellets are not damp or wet. If your fuel is too damp, this

stove may not be able to run on the lower Heat Range settings (the fire will die out). Be

sure to keep sawdust, debris and fines out of the unit.

8. Use three-inch (3”) U.L.-approved CORN VENT TWIST-LOCK PIPE when installing this

stove and follow the manufacturer’s specifications for installation and clearances (we highly

recommend Dura-Vent corn twist-lock pipe – our Part Number AC-33000). Even though

this pipe interlocks, it is recommended to seal all connections with high temperature

silicone (our Part Number AC-RTV3) or aluminum duct seal tape. Use at least three

screws to secure the pipe to this unit’s exhaust blower. Also, if you do not use U.L.-

approved twist-lock corn pipe, be sure to use U.L.-approved Corn Vent pipe, and fasten

each joint of the pipe with at least three screws.

9. Outside combustion air is mandatory for these units to work properly. Make this connection

using a 1

7

/

8

” I.D. metal pipe (steel, aluminum or copper) and coupler. Be sure to secure

the pipe to the unit with a clamp or aluminum tape. The outside end should be covered

(screened) to prevent any foreign matter from entering the system. Try to keep the number

of bends in this pipe to a minimum. Our Part Number PU-OAK (Outside Air Kit with flex

pipe) can be used.

NOTE: If the total run of the connection exceeds six feet (6’), use 3” metal pipe and

coupler instead.

10. Regularly inspect the burnpot area, remove the feeder pot and clean all plugged holes.

See Maintenance Section.

11. The ash in the burnpot should be removed regularly, depending on your burn rate. The

area to the right and left of the burnpot is for ash storage; keep the air holes in the burnpot

clean for a more efficient burn. Check your exhaust system frequently. Refer to “Ash

Removal and Disposal” section.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

4

12.

Keep corn, pellets and all other combustible materials a safe distance from the unit.

13. This unit will require floor protection if installed on a combustible surface. The minimum

floor protector for this unit is 36” x 48” which should give you at least six inches (6”) of

protection at the rear and at each side, and six inches (6”) minimum in the front of the unit.

14. Horizontal runs should not exceed four feet (4’) with a maximum vertical flue height of thirty

five feet (35’). At fifteen feet (15’), the pipe should be increased to four inch (4”) corn vent

pipe.

15. This unit should be turned off and allowed to cool prior to cleaning. Any ashes should be

kept in an airtight metal container and not disposed of until they are completely cooled.

16. Read the instructions thoroughly, including instructions concerning the digital control

board, and save them for future reference.

17. Do not allow paint, chemicals or construction dust on or near your unit. Do not allow liquid

or ANY foreign materials on or inside your unit. Shut your unit down and cover it when

painting, construction or similar activity is taking place. Wipe and clean your unit after any

construction is done in your home, or if any foreign material gets on or inside your unit.

You may also need to remove the rear and side cover plates to your unit (unplug unit first)

and vacuum and clean the motors and inside of your unit.

18. Improper gasket maintenance, including failure to replace gaskets, can cause air leaks

resulting in smoke-backs.

19. Remember that, as with any appliance, there is user responsibility involved, including

installation, operation and maintenance of this product. Be sure to check local codes, and

call Technical Support at (800) 245-6489 if you have any questions.

20. Be sure to follow the directions of all manufacturers of third party products that you

use, including exhaust pipe, etc. Never apply firestarter products (including gel) to a

hot surface or hot coals.

21. Basement Installation: Basement installation should be performed only by a professional

installer. For basement installations, a three inch (3”) pipe and coupler must be used for

Outside Combustion Air, and a minimum clearance of three feet (3’) must be maintained

from the ground to the corn vent exhaust pipe outside the dwelling. Keep in mind that each

elbow used reduces draft by up to 30%; it is good practice to add three feet (3’) of vertical

rise for each elbow used. Example: After the 2

nd

elbow used, add six feet (6’) of vertical

rise before terminating your vent pipe.

22. DANGER! Do not open the door on this unit if the Stirrer is still moving! See instructions

on “Setting the Stirrer” later in this manual. See burnpot installation pictures.

IMPORTANT NOTICE:

This unit must be properly installed to prevent the possibility of a house fire or “smoke-

back.” The instructions must be strictly adhered to.

Do not use makeshift methods or material which may compromise the installation.

Your unit requires periodic maintenance and cleaning (refer to manual). Failure to

maintain your unit may lead to a variety of problems, including but not limited to smoke

spillage into the home. England’s Stove Works will not be liable for consequential or

indirect damages to property or persons resulting from the use of this product.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

5

UNIT PREPARATION

1. Attach the spring handle to the door by turning it counterclockwise. Important: Also

check hopper latch – must be tight so that the top is sealed to prevent back-burn.

2. Test your 110-volt outlet for current and then plug in the unit. (Must be a 15A circuit

minimum, should be 20A if circuit is GFIC protected. We highly recommend a

surge protector for our unit, as the control panel is electronic).

3. Be sure to “dry run” your unit for 20 minutes before connecting it to the flue. During this

time the blowers and auger will operate at different times throughout the 20-minute

period (it should stop automatically after 20 minutes; 30 minutes for corn).

IMPORTANT INFORMATION – READ BEFORE OPERATING

 When installing your Pellet/Corn/Multi-fuel stove, particular attention needs to be made in

regards to fire protection. If the unit is not properly installed, a house fire may result. For

your safety, follow the installation and operation instructions provided, and if a question

arises contact local building or fire officials about restrictions and installation

requirements in your area.

 Read the Operation and Fuel sections of this manual before plugging in your unit.

 Always unplug the unit before attempting any service work.

 Do not connect the unit to a chimney flue already serving another appliance.

 When installing the chimney pipe to the unit, it is important to remember that the unit

operates on negative pressure and the chimney on positive pressure. All chimney

connections, elbows, and fittings must be air-tight. (Proper venting practices must be

followed. Consult with a venting professional.)

 Ashes must be disposed of in a metal container with a tight fitting lid.

 All minimum clearances to combustibles must be followed.

 It is important to use fuel that is clean, dry and consistent. It is recommended that

you purchase your entire heating season supply of fuel at one time, to make sure it is the

same.

 This unit has been tested with 3 different fuels as of May 2007. Call Technical Support at

(800) 245 6489 if you have questions regarding the fuel you are trying to burn.

This stove was tested with:

1. Hardwood Pellets

2. Shelled Corn

3. Cherry Pits

Visit our web site at www.heatredefined.com for helpful information,

frequently asked questions, parts/accessory orders and more!

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

6

 The Pellet/Corn/Multi-fuel stove is tested for operation with corn with 14% or less

moisture content; it is recommended that corn with 11-12% moisture be used for most

efficient operation of this unit. Corn with over 12% moisture has a lower BTU value

and will be hard to burn on the lower settings.

 Corn must be clean and free from debris; never burn corn straight from the field. Stalk

parts, excessive fines and cob remnants, etc. will clog the auger mechanism. We highly

recommend the use of a sifter; sifters to filter your corn are available from dealers.

Damage caused by dirty and/or unfiltered (unsifted) corn is not covered by the product

warranty – ask for and use clean filtered bagged corn only.

 DISCLAIMER NOTICE: No guarantee is made regarding the heating capacity of this

product. The actual area that this unit will heat depends on factors such as building

conditions, heat loss, type of construction, amount and type of insulation, type of air

movement and heat distribution, and the location of the product.

 Important: Your home must be checked to verify that there is no negative pressure that

will affect the operation of this appliance.

 IMPORTANT: DO NOT BURN “TREATED” SEED CORN IN YOUR STOVE. Seed corn

is treated with chemical pesticides that are harmful or fatal if swallowed; therefore, seed

corn is dangerous to have in the house, especially where children can reach it. Burning

treated seed corn in your stove will void your warranty and will destroy the exhaust

system on the unit.

 There are many varieties of corn grown around the world. Each variety has unique

characteristics including the shape and size of the kernel. Your stove will burn more

consistently with a small to medium kernel corn. If the kernel size of the corn varies

greatly or if you switch sources frequently, you will get a less consistent burn. Do not use

corn with high wax content.

 Vacuum the hopper out after every 6-8 bags to eliminate buildup of saw dust and fines

from corn.

 Your unit was primarily designed to burn pellets, but will also burn dried cherry pits.

Make sure your supplier is selling Dried Cherry Pits (preferably with less than 4%

moisture content) for use as fuel in pellet burning stoves.

 IMPORTANT: DO NOT USE CHERRY PITS DESIGNED FOR CRAFTS AND HOBBIES.

This type is usually bleached and/or over-dried.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

7

VENT TERMINATION CLEARANCES

A) MIN. 4-FT CLEARANCE BELOW OR BESIDE ANY DOOR OR WINDOW THAT OPENS.

B) MIN. 1-FT CLEARANCE ABOVE ANY DOOR OR WINDOW THAT OPENS.

C) MIN. 2-FT CLEARANCE FROM ANY ADJACENT BUILDING.

D) MIN. 7-FT CLEARANCE FROM ANY GRADE WHEN ADJACENT TO PUBLIC

WALKWAYS.

E) MIN. 2-FT CLEARANCE ABOVE ANY GRASS, PLANTS, OR OTHER COMBUSTIBLE

MATERIALS.

F) MIN. 3-FT CLEARANCE FROM A FORCED AIR INTAKE OF ANY APPLIANCE.

G) MIN. 2-FT CLEARANCE BELOW EAVES OR OVERHANG.

H) MIN. 1-FT CLEARANCE HORIZONTALLY FROM COMBUSTIBLE WALL.

I) VENTS INSTALLED WITH MECHANICAL EXHAUSTERS SHALL TERMINATE NOT LESS THAN 12 IN.

(305MM) ABOVE THE HIGHEST POINT WHERE THEY PASS THROUGH THE ROOF SURFACE.



Notes on termination of Pellet Vent Pipe from NFPA211(2006ed.)Section10.4Termination:10.4.5

(See also “INSTALLATION” section of manual AND additional notes above):

- Not less than three (3) feet above any forced air inlet located within ten (10) feet.

- Not less than four (4) feet below, four (4) feet horizontally from, or one (1) foot above any door, window

or gravity air inlet into any building.

- Not less than two (2) feet from an adjacent building, and not less than seven (7) feet above grade where

located adjacent to public walkways.

The exhaust exit shall be arranged so that the flue gases are not directed so that it will affect people, overheat

combustible structures, or enter buildings. Forced draft systems and all parts of induced draft systems under

positive pressure during operation shall be installed gastight or to prevent leakage of combustion products into a

building. Through-the-wall vents shall not terminate over public walkways, or where condensate or vapor could

create hazards or a nuisance.

Be sure to follow local codes and all manufacturer’s instructions (including exhaust pipe).

Consult a professional installer and/or call Technical Support if you have any questions.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

8

GUIDELINES FOR EXHAUST VENTING SYSTEMS DESIGN

INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER

 A UL listed three-inch or four-inch (3”or 4”) type “L” corn vent exhaust system must be

used for installation and attached to the pipe connector provided on the back of the unit.

Use a three-inch to four-inch (3” to 4”) adapter for four-inch (4”) pipe. A cap must be used

at the termination of type “L” vent chimneys. Four-inch (4”) type “L” is recommended for

elevations above 2,500 feet above sea level.

 Do not terminate vent in any enclosed or semi-enclosed area, such as: carports, garage,

attic, crawl space, under a deck or porch, walkway or enclosed area, or any location that

could build up a concentration of fumes such as a stairwell, covered breezeway, etc.

 Vent surfaces can get hot enough to cause burns if touched. Non-combustible shielding

or guards may be required.

 Do not install a flue damper in the exhaust vent of this unit.

 Termination must exhaust above air inlet elevation. Installation MUST include three (3)

vertical feet of corn vent pipe. This will create some natural draft to prevent the possibility

of smoke or odor during unit shutdown, and keep exhaust from causing a nuisance or

hazard from exposing people or shrubs to high temperatures. DO NOT CONNECT THIS

UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE. DO NOT CONNECT

DIRECTLY TO A MASONRY CHIMNEY.

 Distance from doors and windows, gravity or ventilation air inlet into building: not less

than four feet (4 ft.) below, four feet (4 ft.) horizontally from, one foot (1 ft.) above (this

does not apply if the windows are non-opening or have been fixed so they cannot open).

 Distance from bottom of termination and grade - three feet (3 ft.) minimum. This is

conditional upon the plants and nature of the grade surface. The exhaust gases are hot

enough to ignite grass, plants, shrubs, etc. located in the vicinity of the termination. The

grade must not be a lawn. Distance from bottom of termination and public walkways is

seven feet (7 ft.) minimum.

 Distance to combustible materials – three feet (3 ft.). This includes adjacent buildings,

fences, protruding parts of the structure, roof overhang, plants and shrubs, etc.

 The installation must include a cleanout tee to enable the collection of fly ash and permit

periodic cleaning of the exhaust system. 90° elbows accumulate fly ash and soot,

thereby reducing exhaust flow and performance of the unit. Each elbow or tee reduces

draft potential by up to 30%.

NOTE: YOUR UNIT MUST BE INSTALLED BY A QUALIFIED

INSTALLER, SUCH AS AN NFI CERTIFIED SPECIALIST

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

9

 Total length of horizontal vent must not exceed 48” (4 ft.). Use three-inch (3”) U.L.-

approved CORN VENT TWIST-LOCK PIPE when installing this stove and follow the

manufacturer’s specifications for installation and clearances (we highly recommend Dura-

Vent corn twist-lock pipe – our Part Number AC-33000). Even though this pipe interlocks,

it is recommended to seal all connections with high temperature silicone (our Part Number

AC-RTV3) or aluminum duct seal tape. Use at least three screws to secure the pipe to this

unit’s exhaust blower. Also, if you do not use U.L.-approved twist-lock corn pipe, be sure to

use U.L.-approved Corn Vent pipe, and fasten each joint of the pipe with at least three

screws.

 The “L” vent or corn vent stainless exhaust system must be installed so as to be GAS

TIGHT! Follow the vent manufacturer’s installation instructions.

 The area where the vent pipe penetrates the exterior of the home must be sealed with

silicone or other means to maintain the vapor barrier between the exterior and the interior

of the home.

NOTE: These are guidelines only. Proper venting is accomplished by design and

common sense. In most installations, three-inch (3”) diameter venting is

adequate. If it does not vent properly, you must change it to four-inch (4”)

diameter venting.

DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

10

BURNING SOLID FUELS

Ashes will need to be removed from the unit periodically. See Ash Removal section. You can

minimize cleaning required and maximize efficiency by maintaining the proper draft.

This unit has been designed to burn premium pellets, dry shelled corn or dried cherry pits that meet

the Pellet Fuels Institute (PFI) standards.

WOOD PELLETS

Be consistent in your choice of wood pellet supplier. Pellets will vary in content and burn

characteristics from supplier to supplier.

 Check your pellets for foreign objects. Your stove warranty will not cover any damage caused

due to foreign objects in the fuel supply.

 Store your pellets in a dry place to prevent them from absorbing added moisture.

 To decrease sawdust buildup, the hopper will need to be vacuumed out after every 6-8 bags of

pellets, or more often if the quality of the pellets is poor. You may need to screen each bag of

pellets if the sawdust becomes a problem.

 Wood pellets vary in size and also ash content (from less than 1% to 3% or more). Your unit will

burn more efficiently with small to mid-size pellets. Low ash content pellets will allow you to burn

the stove longer between cleanings.

 Your unit is designed to burn pellets that are no larger than one-quarter inch (¼”) in diameter,

and no longer than two and one-half inches (2 ½”) long.

CAUTION: DO NOT PLACE SUCH FUELS WITHIN THE SPACE HEATER’S INSTALLATION

CLEARANCES OR WITHIN THE SPACE REQUIRED FOR CLEANING AND ASH

REMOVAL.

SHELLED CORN

(Dry, preferably with 11-12% moisture content)

Never burn “deer corn” as it frequently contains molasses/sugars. Store your corn supply in a dry

place and keep bags or container sealed to prevent your corn from absorbing excess moisture. Test

the moisture content regularly to ensure proper dryness.

IMPORTANT: DO NOT BURN “TREATED” SEED CORN IN YOUR STOVE. Seed corn is treated

with chemical pesticides that are harmful or fatal if swallowed; therefore, seed corn is

dangerous to have in the house, especially where children can reach it. Burning

treated seed corn in your stove will void your warranty and will destroy the

exhaust system on the unit.

CHERRY PITS

(Dry, preferably with less than 4% moisture content)

Your unit was primarily designed to burn pellets, but will also burn dried cherry pits. Make sure

your supplier is selling Dried Cherry Pits for use as fuel in pellet burning stoves.

IMPORTANT: DO NOT use cherry pits designed for crafts or hobbies.

This type is usually bleached or over-dried.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

11

FLUE SYSTEM

Caution: Follow the pipe manufacturer’s installation instructions and directions for passing

through combustible walls and ceilings.

Be sure to check local codes in your area.

NOTE: See the installation drawing later in this manual (Illustration 1).

This unit is equipped with a negative draft system that pulls combustion air through the

burnpot and pushes the exhaust air out of the dwelling. If this unit is connected to the flue

system other than the way explained in this manual, it will not function properly. For any of

these installations, keep in mind that each elbow used reduces draft by up to 30%; it is good practice

to add three feet (3’) of vertical rise for each elbow used. Example: After the 2

nd

elbow used, add

six feet (6’) of vertical rise before terminating your vent pipe.

Corn Vent Pipe

The UL approved corn vent pipe that we recommend is a twist lock system; however, it is still

recommended that high temperature silicone (our Part Number AC-RTV3)

or aluminum duct seal

tape be used at each joint. England’s Stove Works recommends the use of Dura-Vent twist-lock

pipe (if you use other pipe, consult your local building codes and/or building inspectors, and secure

each joint with at least three screws—see “Important Information” section). Do not use “B” vent gas

pipe or galvanized pipe with this unit. The corn pipe is designed to disassemble for cleaning and

should be checked several times during the burning season — corn vent pipe is not furnished with

the unit and must be purchased separately. Do not install a flue damper of any kind in this

system, and do not connect this unit to a flue system serving another heating appliance.

Through the Wall

To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the

exhaust adapter is at least eighteen inches (18”) above ground level, a straight section of corn pipe

can be used to initially pass through the wall (see Illustration 1). Your dealer or our factory should be

able to provide you with a kit that will handle most of this installation, which will include a wall thimble

that will allow the proper clearances through a combustible wall. Once outside the structure, a three-

inch (3”) clearance should be maintained to the outside wall and a clean out tee should be placed on

the pipe that extends through the wall. We recommend a minimum of three feet (3’) of vertical pipe

with a 90-degree turn away from the house. At this point, a one-foot (1’) section and horizontal cap

will complete the installation (see Illustration 1).

A wall strap should be placed just below the last 90-degree section to make the system more

stable. If you live in an area that has heavy snowfall, it is recommended the installation be taller than

three feet (3’) to get above the snowdrift line.

The same type installation can be used if your stove is below ground level by adding the clean-

out section and vertical pipe inside until ground level is reached. However, we recommend

basement installation be performed only by a professional installer. For basement installations, a 3”

(three inch) pipe and coupler must be used for Outside Combustion Air, and a minimum clearance of

three feet (3’) must be maintained outside the dwelling from the ground to the Corn Vent Exhaust

Pipe.

Call (800) 516-3636 to inquire about the AC-33000 Through-the-Wall Kit or

Visit our web site at

www.heatredefined.com for ordering information!

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

12

The through-the-wall installation is the least expensive and simplest installation. In a through-

the-wall installation you should be mindful of the snowdrift line, as well as dead grass and leaves.

We recommend a three foot (3’) minimum vertical rise on the inside or the outside of the dwelling.

Through the Ceiling

When venting the stove through the ceiling, the pipe is connected the same as through the wall,

except the clean out tee is always on the inside of the house, and a 3” adapter is added before the

clean-out tee. You must use the proper ceiling support flanges and roof flashing supplied by the pipe

manufacturer -- follow the pipe manufacturer’s directions and Illustration 1 in this manual. It is

important to note that if your vertical runs of pipe are more than fifteen feet (15’) at this point, the corn

vent pipe should be increased to four inches (4”) in diameter. Do not exceed four feet (4’) of pipe on

a horizontal run, and do attempt to use the least number of elbows in the flue system. If an offset is

used it is better to install a 45-degree elbow whenever possible. Please remember, installing elbows

may inhibit your draft by up to 30% per elbow.

Outside Air (Outside Combustion Air Intake)

Outside air is mandatory for this unit to operate properly. This unit has been designed and tested

with this connection, because so many homes are airtight and there is not adequate combustion air

available inside the dwelling. The air intake pipe is located on the bottom side of the burnpot (from

the rear) and measures 1 ½” inside diameter (I.D.). The connection can be made with a metal 1

7

/

8

”

I.D. coupler and pipe (see “Important Information” section of manual), and should exit through the

wall. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end of the

pipe should be covered (screened) to prevent foreign matter from entering the system.

Our Outside

Air Kit (Part Number PU-OAK) can be used.

If the unit is located below ground level, you will need to

run the pipe up and then outside the dwelling. NOTE: If the total run of the connection exceeds six

feet (6’), if more than two elbows are used, or if a basement installation, use 3” metal pipe (and

coupler) instead.

Mobile Home Installation

Secure the heater to the floor using the two holes in the pedestal. If the unit is on a combustible

surface, you will need to drill matching holes in the floor protection that you choose (see Floor

Protection section). Do not disturb the structural integrity of the home, and be sure the unit is

permanently electrically grounded to the chassis of your home. Remember that outside combustion

air is mandatory, and not to install the unit in a sleeping room of the home.

Important Notes Concerning Installation:

IMPORTANT: Improper hook-up (too much pipe, too many elbows, etc.) will cause

the unit not to operate. Call Technical Support (800-245-6489) if you

have questions about your hook-up or if your unit will not operate.

IMPORTANT SAFETY NOTE: If the unit or chimney connector pipe “glows” red (or white), the stove

is over-fired. This condition could cause a house or chimney fire. Do

not operate your unit too hot, or over-firing may result.

*IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage

caused by the malfunction of a stove due to improper venting

or installation.

Call 800-245-6489 and/or consult a professional installer if you have any questions.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

13

FLOOR AND WALL PROTECTION

Floor Protection

If your floor is constructed of a non-combustible material such as brick or concrete, there is no need for

floor protection. If the floor is constructed of a combustible material such as hardwood, linoleum, or carpet, then

you will be required to use floor protection between the unit and the combustible. The protection should be U.L.

approved or equal, and should be large enough to provide a minimum of six inches (6”) behind and on both

sides of the stove. The clearance in front of the stove should be at least six inches (6”). This freestanding pellet

unit will need a minimum 36” x 48” floor protector.

Wall Protection

From the rear of this stove only six inches (6”) of clearance is required to paneling, wallpaper or drywall

(we recommend more clearance for maintenance access). Six inches (6”) would be required to a sidewall.

From the corner of the stove, 4 ½” of clearance is required. Alcoves: The alcove must be a minimum of sixty-

six inches (66”) from floor to ceiling. Six inches (6”) of clearance is required from the stove to an alcove

sidewall; six inches (6”) is required to an alcove back wall.

The corn vent pipe would require the standard three inches (3”) clearance, or as recommended by the pipe

manufacturer. Normally, additional wall protection is not required with this type unit.

Illustration 1

Freestanding Pellet/Corn/Multi-fuel Installation

Caution: Follow the pipe manufacturer’s installation instructions and directions for

passing through combustible walls and ceilings. Check local codes in your area.

Our Part AC-33000

is acceptable for

through-the-wall

installation.

(We recommend 4”

for 2500+ ft.

installations, Our

Part AC-33100.

)

Must have

minimum 3”

adapter before tee

for longer run.

For shorter run, tee

alone is acceptable.

Basement Installation

should be performed by

professional installer. Use

3” metal pipe and coupler

for Outside Combustion

Air. Minimum 3 ft. (3’)

clearance from ground to

the Corn Vent Exhaust

Pipe.

1. If 3” flue pipe exceeds 15’ in length, increase to 4” flue pipe for remaining flue connections.

2. Total flue length should not exceed 35’.

3. Horizontal run not to exceed 4’.

4. Floor protector required: Min. size 36” x 48”.

5. If the total run of outside air connection exceeds 6’, if more than 2 elbows are used, or if a

basement install, use 3” metal pipe (and coupler) instead.

6. Outside Air is mandator

y

f

or

p

ro

p

er sa

f

e o

p

eration.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

14

OPERATING INSTRUCTIONS

CAUTION: DO NOT OPERATE WITH THE DOOR OPEN.

Do not burn trash (paper bags, etc.) in this unit.

This stove has an induced draft system and is designed to operate continuously, as frequent

shutdown is not required. The setting of the “Heat Range” touch pad will control the heat output

and the amount of fuel the unit will burn (see “Control Board” section).

NOTE: This stove is using solid fuel and will not restart automatically unless a thermostat is

installed. See page 26 – Thermostat instructions.

* NOTE: Blower Speed will automatically be adjusted to the desired Heat Range that you select.

START- UP PROCEDURES

SETTING THE STIRRER

Warning: Do not open the door on this unit if the Stirrer is still moving!

Bodily Injury can occur!

The stirrer must be “set” before each burn so that the 4-prong side of the stirrer is pointing

straight up (see diagram below). To rotate the Stirrer, press and hold the “AIR ON TEMP” (i.e. “Air

On”) button (on the bottom of the Control Panel); it will stop rotating when you release the button.

To turn Stirrer Off and On: The Stirrer may be turned Off by pushing the “Air On” button on the

bottom of the Control Panel, and then pressing both Down arrows on the “Blower Speed” and “Heat

Range” until you see a “0” in the Blower Speed window. The Stirrer may be turned back On by

pressing the “Air On” button on the bottom of the Control Panel, and then pressing both Up arrows

on the “Blower Speed” and “Heat Range” until you see a “1” in the Blower Speed window.

CAUTION: Never use gasoline, lantern fuel, kerosene, charcoal lighter fluid, diesel fuel or

any other flammable liquid to start the fire. Keep all combustible materials at a

safe distance from stove.

The Heat Range and Blower Speed will automatically be set to setting “5” (default setting during

start up) to ensure that proof of fire is detected. During the 20 minute start-up period the user can set

the controls to a desired heat setting and after the 20 minute start-up the unit will operate at that user

setting. When burning corn, start-up period is 30 minutes.

Stirrer

–

Ill

ustration

2

This prong must be in the upright

position when restarting the stove

(the 4-prong side is in 12:00 position)

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

15

WARNING!

For pellets and corn, when the “Air On” button on the bottom of the Control Board is pressed, you

must make sure you see the number “1“ in the Blower Speed window. The Stirrer must be running in

the pellet and corn modes (mode 1 – pellet; mode 5 – corn, see Fuel Change Procedure, page 16). (As

previously stated, the Stirrer will stop if you press the “Air On” button and press the Blower Speed and

Heat Range arrows down until you see a zero (0) in the window. Before you restart your unit you must

see the number “1“ in the Blower Speed window - see previous page).

Make sure the Stirrer is turning before you walk away from the unit. The Stirrer will start 4 minutes into

the startup mode. It turns very slowly, so you will want to observe it to make sure it is actually moving!

NOTE: On the “first fire” (the first time you burn the unit), the Control Panel should be set at a “5” Heat Range

and “5” Blower Speed for at least 3 hours to allow the unit to “cure” as the oils from the manufacturing

process burn off. Windows and doors in the home should be opened to help ventilate as these oils

burn off.

NOTE: If the unit does not start, DO NOT try to restart the unit until it has cooled completely down. If the unit

does not start or maintain a fire, you will receive an E-2 in the Heat Range and Blower Speed window

of the Control Board. If this occurs, wait until unit has cooled completely down and repeat these

steps.

NOTE: The burnpot and Stirrer are part of a floating system. This means you will see it rise up and go down.

The unit is designed to burn multi-fuel; this feature will allow the unit to run and not hang-up or lock-

up on a hard piece of corn, etc. It may make a “jumping” noise when you first start the unit, but it will

go away after your unit heats up. It will not harm the unit. It is a heavy duty system made with

stainless steel, designed to last many trouble-free years.

FUEL NOT FEEDING CORRECTLY

If the fuel is not feeding correctly, the feed auger could possibly be misaligned due to factors such as rough

handling during shipping. If you suspect your feed auger is misaligned, call Technical Support at (800) 245-

6489.

Automatic Start-Up

When the “ON” button is pressed from a cold start, the unit is in “Start-Up” (after 3 seconds, there will be an

“S U” in the Heat Range and Blower Speed windows to verify this). While in this mode, the unit has a preset

heat range and will remain in this mode for 20 minutes (30 minutes in corn mode) to prevent the unit from over-

firing. During this start-up period you can set the Control Board at the setting you desire; after the start-up is

complete, the unit will operate at the user setting.

Manually Starting Your Unit

In the event the Auto-Start does not initiate, you may manually start your unit. To manually start your unit,

first clean any pellets out of the burnpot (to prevent over-feeding). Place a handful of new pellets in the

burnpot, then spread a small amount of pellet fire starter over the pellets and ignite them. After the pellets

ignite, close the door to your unit and press the “ON” button (if the door is closed before the pellets fully ignite,

the Exhaust Blower could put out the fire).

Recommended fire starter materials are: Wax-impregnated wood chips, cardboard cubes or firestarter

chips designed for pellet and corn burning stoves. Follow any manufacturer’s directions for these products,

and NEVER place any firestarter on any hot surface or hot coals.

CAUTION: Never use gasoline, lantern fuel, kerosene, charcoal lighter fluid, diesel fuel or any other

flammable liquid to start the fire. Keep all combustible materials at a safe distance from

stove.

Wet corn may not start with your auto start igniter. It will help to keep a bag of pellets handy. If your corn

does not ignite, shut the unit down, clean out the burnpot and make sure the unit is not warm. Place a cup full

of wood pellets in the in the burnpot, place a small amount of one of the recommended fire starters (listed

above) on the wood pellets and ignite the pellets. Allow the pellets to burn for 1-2 minutes then close the door

and push the “ON” button.

CAUTION: The Firebox should be cool to the touch before attempting to start the unit.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

16

NOTE

If the unit does not start or maintain a fire, you will receive an E-2 in the Heat Range and Blower

Speed window of the Control Board. If this occurs, wait until unit has cooled completely down and

repeat.

To remove the Stirrer for cleaning

While the unit is COLD and the unit is off, press and hold the “AIR ON TEMP” (i.e. “Air On”)

button until the Stirrer is at the “12:00” position (with the 4 prongs pointing up). Pull the hitch pin

(marked in Illustration 3). Lifting the burnpot and Stirrer at the same time, remove the Stirrer from the

burnpot. Clean and clear all holes in the burnpot and replace Stirrer and burnpot back into the unit.

NOTE: When replacing the burnpot, notice there is a welded piece that is always set toward the

back of the Firebox. Also, be sure to replace the hitch pin.

Illustration 3

Locking

Collar

Illustration 4

Hitch Pin

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

17

FUEL CHANGE PROCEDURE

When starting the stove with corn, push the “AIR ON TEMP” button and hold, which will rotate the

Stirrer mechanism in the burnpot. Release the button when the 4-prong side of the Stirrer is straight

up (in the “12:00” position, as shown in Illustration 2, page 13). Then follow the previous instructions

concerning placing the handful of pellets in the burnpot and starting your fire (Manually Starting Your

Unit, page 14).

Changing from Pellets to Corn

Your unit was primarily designed to burn pellets, but will also burn corn. Your unit comes ready to

burn pellets by default; if you would like to burn corn in your unit, follow the steps below.

WARNING: Do not open the door on this unit if the Stirrer is still moving!

See instructions “Setting the Stirrer” on page 13 in this manual.

NOTE: Before performing these steps make sure the unit is out and completely cold!!

1. The control board must be reset to burn corn. Unplug the unit and plug back in, then press

the Blower Speed up and down buttons at the same time and release. You should see a “1

through 8” in the Heat Range window. Push the Heat Range up arrow until you see a “5.”

Wait for the window to clear. You are now set to burn corn. To change the stove back to

burn pellets: Push the Heat Range down arrow until you see a “1.” Wait for the window to

clear. You are now set to burn pellets.

2. Follow lighting instructions.

Changing from Pellets to Cherry Pits

Your unit was primarily designed to burn pellets, but will also burn dried cherry pits. Make sure

your supplier is selling Dried Cherry Pits for use as fuel in pellet burning stoves. Do not use cherry

pits designed for crafts or hobbies, as this type is usually bleached or over-dried. Your unit comes

ready to burn pellets by default; if you would like to burn cherry pits in your unit, follow the steps

below.

WARNING: Do not open the door on this unit if the Stirrer is still moving!

See instructions “Setting the Stirrer” on page 13 in this manual.

NOTE: Before performing these steps make sure the unit is out and completely cold!!

1. Remove the Stirrer shaft (See Illustrations 3 & 4 - Page 15). Do not use the Stirrer when

burning cherry pits.

2. The control board must be reset to burn cherry pits. Unplug the unit and plug back in, then

press the Blower Speed up and down buttons at the same time and release. Push the Heat

Range up arrow until you see a “6.” Wait for the window to clear. Remember to remove the

Stirrer (page 15). Set Air On button to “0” (see page 14 – first paragraph). You are now set

to burn cherry pits. To change the stove back to burn corn: Push the Heat Range down

arrow until you see a “5.” Wait for the window to clear. You are now set to burn corn. To

change the stove back to burn pellets: Push the Heat Range down arrow until you see a

“1.” Wait for the window to clear. You are now set to burn pellets. Remember to replace the

stirrer and set it to run when burning pellets and corn (see Setting the Stirrer, page 13).

3. Follow lighting instructions.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

18

E-Codes

“E-Codes,” or Error Codes, are codes that will appear in the Heat Range and Blower Speed

windows of the Control Board if your unit experiences problems. If you receive these codes,

wait until the unit is cooled completely down before trying to restart your unit.

If the unit continues to display any E-Code(s), please contact Technical Support at

(800) 245-6489 before further attempting to restart your unit.

NOTE: “E-0” indicates “No Error”

E-2 = Fail to Start

E-3 = Unit Overfired

If you see the E-3 code displayed on your control board, you have overfired your

unit. You must let the unit cool and clean the Firebox and burnpot. Be sure to

clean the orifices (holes in the burnpot). You should not burn your unit on High

(Heat Range 9) continuously when burning corn. After a couple of hours of burning

corn on high, turn the Heat Range to 7 and the Blower Speed to 9. WARNING:

Running the unit on high, when burning corn for long periods, can damage

the unit.

OPERATIONAL NOTES

First Fire: When you push the “ON” button, the Control Board will automatically be set at both

“Heat Range” and “Blower Speed” to setting “5.” Allow the stove to burn in this

manner for at least three (3) hours. This will allow the unit to “cure out” as the paint

and the oils from the manufacturing process burn off. We recommend you open

doors and windows in your dwelling during this process.

Subsequent Cold Starts: In a cold start situation, the unit should be operated at a “5”

setting until the room air blower begins to operate.

IMPORTANT NOTES:

- Please be patient. Your unit has a large burnpot and it takes awhile to

equalize (reach maximum heat levels). Do not be concerned by the size of

the flame, as this unit gets much hotter than the flame appears.

- Use gloves when filling the hopper.

- If you leave the hopper open too long, the stove will shut down.

NOTE: Press the “ON” button only once on start-up Except when the hopper is empty

(when you run out of fuel, or for your first fire, see above), press and hold the “ON”

button for 10 seconds to purge the unit. Pressing the “ON” button a second time

during the start-up cycle will cause the start-up cycle to begin again.

IMPORTANT: If the unit fails to start properly, or does not properly complete the Shut-Down

procedure, open the closest outside door and a window to eliminate the

home’s natural draft BEFORE opening the stove’s door or hopper lid. This

will allow any smoke to exit through the external air hook-up instead of spilling

into the home.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

19

SHUT-DOWN PROCEDURE

WARNING: NEVER SHUT DOWN THIS UNIT BY UNPLUGGING IT

FROM THE POWER SOURCE.

Refer to the following instructions:

Press the “OFF” touch pad to put the stove in the “Shut-Down” mode. There will be an

“S D” in the Heat Range and Blower Speed windows while the unit is shutting down to verify

this. At this time the red light above the “OFF” pad will illuminate. When the “OFF” pad is

touched the auger will instantly stop feeding fuel to the auger tube, but the room air blower,

exhaust blower and Stirrer will continue to operate. When the internal temperature drops to

95 degrees the room air blower will cease to operate, and when the internal temperature

drops to 90 degrees the exhaust blower will stop. The red light will then shut off and the

entire stove will be shut down. The hotter the unit is operating, the longer it will take for the

stove to complete the Shut-Down cycle.

Note: The unit will exit the Shut-Down cycle if you press the “ON” button during Shut-

Down.

NOTE: If your unit overheats, the auger will stop feeding, "E3" will be displayed on

the control board and the unit will go into Shut-Down. If this happens you need

to wait 45 minutes before trying to re-light the unit.

If you have any questions or problems contact the Technical Support Department:

Technical Support Department [email protected]

P.O. Box 206 Parts Orders ONLY: 800-516-3636

Monroe, VA 24574 Questions: 800-245-6489 (Fax: 434-929-4810)

You may also order parts and options, view frequently asked questions and more, on our

Web Site:

www.heatredefined.com

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

20

DAILY OPERATION

Refueling the Unit

Always press the “OFF” touch pad before refueling. The hopper on this stove holds

approximately 50-lbs. (wood pellets), and should be refilled when the fuel level drops to three or four

inches.

Note: The hopper lid will be warm; therefore, you should always use some type of hand protection.

NEVER place your hand near the auger while the stove is operating.

Note: Always ensure that all corn and pellet matter is cleared from the hopper lid gasket before

closing. Be sure to close and latch hopper securely before re-firing. Do not operate this

unit with the hopper lid open or unsecured.

Power Outage

If the power to the unit is interrupted for approximately three minutes or less, the unit will resume

operation when power is restored according to the following table:

Unit’s State Before Power Loss State When Power Returns

ON Start-Up

Start-Up Start-Up

Shut-Down Shut-Down

OFF OFF

If the power is interrupted for more than (approximately) three minutes, the unit will be “OFF”

when power returns.

Important: Do NOT open the hopper lid or the door to the unit during power outage. Open

the closest outside door and a window to eliminate the home’s natural draft. Wait

for power to be restored and then press the “ON” button to re-start the unit, if desired.

Remember:

1) It is very important for the unit to be vented properly (see instructions on Outside Air),

as the natural draft is needed to clear the smoke from the stove.

2) Do not open the hopper lid (or the unit’s door). This may cause fire to burn in the

hopper.

Fuel Outage

If your unit runs out of fuel, let the unit go through the complete Shut-Down cycle and then follow

the instructions for restarting the unit.

NOTE: DO NOT TRY TO RESTART THE UNIT HOT. If the unit runs without pellets or corn,

after one hour the unit will shut down.

Combustion Blower Failure

If the Combustion (exhaust) Blower should fail on this unit, a Vacuum Shut-Down Switch will

automatically stop the auger. This will cause your stove to stop feeding fuel to the burnpot, and the

unit will eventually stop completely. Check your power supply, including tripped breakers, etc. If the

blower has failed, you will need to contact Technical Support at (800) 245-6489.

NOTE: It is very important for the unit to be vented properly (see instructions on Outside Air), as the

natural draft is needed to clear the smoke from the stove.

La page charge ...

Englander 10-CPM Guide d'installation

Englander 10-CPM Guide d'installation

dans d''autres langues

Documents connexes

Autres documents