19
User P1 - the ArcPixel Power plays user program 1.
User P2 - the ArcPixel Power plays user program 2.
User P3 - the ArcPixel Power plays user program 3.
Program Play - entering this menu provides a complete overview of all programs oered, from which
the selected program can run continuously in a loop .
User 1 - the ArcPixel Power plays user program 1.
User 2 - the ArcPixel Power plays user program 2.
User 3 - the ArcPixel Power plays user program 3.
Program Edit - the ArcPixel Power oers three freely editable programs each up 35 steps. Every program step
includes a step time-the total time occupied by the step in the program.
To edit a program
1. Use the [UP] and [DOWN] buttons to select desired program (User 1-User 3) and press the [ENTER] button.
2. Enter the item S. Count and by means of the [UP] and [DOWN] buttons set desired number of program steps.
This value should be set before starting of programming (e.g. if you want to create a program with 10 steps,
set S. Count=10).
3 Press the [ENTER] button.
4.Select Step 1 and press the [ENTER] button. List of editable items will appear:
Red Z1 - a red LEDs on LED output 1
Green Z1 - a green LEDs on LED output 1
Blue Z1 - a blue LEDs on LED output 1
White Z1 - a white LEDs on LED output 1
:
Red Z4 - a red LEDs on LED output 4
Green Z4 - a green LEDs on LED output 4
Blue Z4 - a blue LEDs on LED output 4
White Z4 - a white LEDs on LED output 4
Step Tim. - a step time (0-25.5 sec)
Copy To Next - this item duplicates the current prog. step to the next prog. step.
5. After editing the items, select next prog. step and edit its items again. Repeat this action for all program steps.
7.7 Special settings
Software Update
- using this function you can update software in the xture via PC and USB (or serial port).
The following are required in order to update software:
- PC running Windows 7/8/10 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX S/N.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note1. Software update should execute a qualied person.If you lack qualication, do not try the update
yourself and ask for help your ANOLIS distributor.
Note 2. IP address, and settings in the menu " Personality" will be set to their default values.
To update software in the xture:
1.Installation of the Software Uploader le (DSU_device name_time identier):
1. The Software Uploader le for is available from the ANOLIS web site at WWW.anolis.cz.
2. Make a new directory ( e.g. ANOLIS_Uploader) on your hard disk and download the software to it.
3. Unpack the program from the archives. Program le has name: DSU_name of corresponding
xture_time identier, eg. DSU_ArcPixel Power-US_14051551.
2.Fixture software updating:
1. Determine which of your port is available on your PC and connect it:
- with the DMX input of the xture if you using the ash cable RS232/DMX
- with the USB input of the Robe Universal Interface if you using the USB cable.
Disconnect the xture from other xtures in a DMX chain. Turn both the computer and the
xture on.
2. Switch the xture to the updating mode:
1.Use the UP] and [DOWN] buttons to nd “Special Settings“ menu.
2.Press the [ENTER] button.
3.Use the UP] and [DOWN] buttons to select “ Software Update“ item.
4.Press the [ENTER] button
5.Use the UP] and [DOWN] buttons to select “ Yes“ option