EarthWise SN70016 Le manuel du propriétaire

Model SN70016

OWNER’S MANUAL

16-IN Snow Thrower

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,

PARTS, SERVICE QUESTIONS? GO TO AMERICANLAWNMOWER.COM OR

CALL 1-800-633-1501. BETWEEN 8 AM – 5 PM EST, MONDAY-FRIDAY FOR

ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual before using

this product.

Precautions that involve your safety.

CAUTION! Read the instruction manual and follow the warning and safety instructions!

CAUTION! Remove plug from outlet immediately if the cable is damaged or cut.

SWITCH OFF! the machine, wait until it comes to a complete standstill and remove plug from outlet prior to

maintenance, cleaning or repair work!

CAUTION! Always wear eye and ear protection.

Wear safe, sturdy, nonskid footwear!

DANGER! objects may be thrown out at high speed when motor is running. Do not walk in front of running

machine.

Keep bystanders at a safe distance.

Keep the electrical cord free of the auger. The auger may damage the cord and cause contact with live

parts.

DANGER! Rotating blades. Keep hands and feet at a safe distance.

Do not place hand under auger.

Do not place hand in front of chute deflector.

Do not place feet under auger.

DANGER! Risk of electric shock.

Do not use in rain or electrical storms.

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

2

Model SN70016

Please note that changes or modifications of this product is not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

SYMBOLS

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

CAUTION: Wear appropriate personal hearing

protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearing loss.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric appliances, basic

safety precautions should always be followed to

reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

CHECK FOR DAMAGED PARTS - Before further

use of the product, any part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, binding of moving

parts, breakage of parts, mounting and any other

condition that may affect its operation. Any part that

is damaged should be properly repaired or replaced.

For assistance call our customer service help line at

1-800-633-1501.

AVOID DANGEROUS ENVIRONMENTS - Don’t

use this product in rainy or stormy conditions. Do

not operate in gaseous or explosive atmospheres.

Motors in these products normally spark, and the

sparks might ignite fumes.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work

area.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Wear rubber boots when operating the snow

thrower. Maintain good footing at all times,

especially on slopes.

USE SAFETY GLASSES - Wear safety glasses

with side shields or goggles that are marked to

comply with ANSI Z87.1 standard when operating

this product.

DOUBLE INSULATION – The snow thrower has

double insulation. This means that all external

metal parts are insulated from the electrical supply.

This is achieved by introducing an insulation layer

between electrical and mechanical parts. The

double insulation guarantees you the greatest

possible safety.

WARNING: Use outdoor extension cords marked

SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A,

or SJTOWA. These cords are rated for outdoor use

and reduce the risk of electric shock.

POLARIZED PLUGS-To reduce the risk of electric

shock, this product has a polarized plug. Polarized

connections will fit together only one way. Make

sure that the receptacle end of the extension cord

has large and small blade slot widths. If the plug

does not fit fully into the extension cord, reverse

the plug. If it still does not fit, obtain a suitable

extension cord. If the extension cord does not fit

fully into the outlet, contact a qualified electrician to

install the proper outlet. Do not change the plug on

the tool or the extension cord in any way.

EXTENSION CORD. Make sure your extension

cord is in good condition. When using an extension

cord be sure it is heavy enough to carry the current

your product will draw. An undersized extension

cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table

shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt,

use the next heavier gage. The smaller the gage

number, the heavier the cord.

It is possible to tie two extension

cords together in a knot to prevent

them from becoming disconnected

during use. Make the knot as

shown, then connect the plug end of

the power cord into the receptacle

end of the extension cord.

WARNING: Keep all connections dry and off the

ground. Do not touch plug with wet hands.

Be aware of the extension cord while operating the

snow thrower. Be careful not to trip on the cord.

Always keep the cord away from the auger.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

3

Model SN70016

Minimum Gage for Cord Sets

Volts Total Length of cord in Feet

120V 0-25 26-50 51-100 101-150

Ampere Rating

More Not More American wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

DO NOT FORCE SNOW THROWER - It will perform

better and safer at the rate for which it was designed.

CAUTION: Never throw snow towards people, pets

or cars and never allow anyone in front of the snow

thrower while in operation.

Objects that might clog the snow thrower or cause

other damage can be hidden in the snow. Clear the

area of doormats, sleds, boards, wires and

other debris prior to use.

If the auger strikes a foreign body, examine the snow

thrower for signs of damage and make any

necessary repairs before restarting and continuing to

work.

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate the snow thrower

when you are tired or under the influence of drugs,

alcohol or medications.

If the snow thrower starts to vibrate abnormally, turn

it off immediately and check for the cause. Vibration

is generally a warning of trouble.

Always turn off the snow thrower, disconnect from

the power supply and wait until the auger comes to a

complete stop before carrying out maintenance or

repairs.

Do not use on graveled surface unless the snow

thrower is adjusted for such a surface in accordance

with the operator’s manual.

Operation of the snow thrower in the hand-held

position is unsafe, except in accordance with the

special instructions for such use provided in the

operator’s manual.

CAUTION: Auger does not stop immediately after the

snow thrower is turned off.

CAUTION: Risk of injury. Do not put hands, feet or

any body part or clothing near the rotating auger.

WARNING: California Proposition 65:

This product contains chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI)

protection should be provided on the circuit or outlet

to be used for the snow thrower. Receptacles are

available having built-in GFCI protection and may

be used.

WARNING: Keep hands away from moving parts.

Never put your hands near the auger to remove

snow, sticks or other debris. Blocked auger can

“spring back” when cleared and may cause personal

injury even when the snow thrower is stopped.

Always use a wooden stick such as a broom handle

to clear blockages.

DISCONNECT UNIT from the power supply when

not in use or when servicing or cleaning. Do not

leave unattended.

DON’T ABUSE CORD - Never carry this product

by the cord or yank the cord to disconnect from the

receptacle. Keep cord from heat, oil, and sharp

edges.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

DO NOT OVERLOAD the snow thrower by using at

too fast a rate to clear the snow.

DON’T OVERREACH - Guide the snow thrower at a

walking pace only. Keep proper footing and balance

at all times.

LIGHTING - Only operate your snow thrower in

daylight or good artificial light.

STORE IDLE UNIT INDOORS-When not in use, the

snow thrower should be stored indoors in a dry area

out of children’s reach.

MAINTAIN UNIT WITH CARE-Keep clean for best

performance and to reduce the risk of injury. Inspect

extension cord periodically and replace if damaged.

Keep handles dry, clean and free from oil.

Do not operate the snow thrower on a slope that is

too steep for safe operation. When on slopes, slow

down and make sure you have good footing.

Before starting the snow thrower make sure the

auger is not touching any object and is free to move.

AVOID UNINTENTIONAL STARTING – Don’t carry

plugged in hedge trimmer with finger on switch. Be

sure switch is off when plugging in.

GENERAL SAFETY

4

Model SN70016

PRODUCT SPECIFICATIONS

Model: SN70016

Power Supply Voltage: 120V-60Hz Sweep Width: 16 in. (406 mm)

Idle Speed: 4500 RPM Max Clearing Depth: 8 in. (200 mm)

Power Consumption: 12 Amp Throwing Distance: Up to 30 ft.

Weight: 14.5 lbs. Clearing Capacity: 430 lbs./minute

5

Model SN70016

PACKING LIST

UNPACKING

Carefully remove the product from the box.

Make sure that all items listed in the packing

list are included.

Inspect all items carefully to make sure no

breakage or damage occurred during shipping.

Do not discard the packing material until you

have carefully inspected and satisfactorily

operated the snow thrower.

If any parts are damaged or missing please

call our customer service help line at

1-800-633-1501 for assistance.

QTY DESCRIPTION

1 Snow Thrower

1 Lower & Upper Handle

1 M6x45 Carriage Bolt & Wing Nut

4 ST4.2x30 Philips Head Self Tapping Screw

1 Adjust Knob

1 ST4.2x50 Philips Head Self Tapping Screw

1 Adjust Knob Cover

1 Wheel Bracket

2 Wheel

2 Hub Cap

2 ST3.9x45 Philips Head Self Tapping Screw

2 ST3.9x55 Philips Head Self Tapping Screw

1 Auxiliary Handle

1 M6x50 Hex Head Bolt & Wing Nut

1 Operator’s Manual

6

Model SN70016

PARTS LIST

1

3

2

4

6

22

5

23

8

9 10

11

12

13

14

15

16

17

18

19 20

21

24

25

26

27

7

No. Description Qty

1 Electrical Plug 1

2 Safety lock off button 1

3 On/Off trigger switch 1

4 Handle 1

5 Auxiliary handle 1

6 Upper cover 1

7 Motor housing 1

8 Adjusting knob 1

9 Acorn nut M8 1

10 Steel wave washer 1

11 Baffle 3

12 Drive shaft assembly 1

13 Drive belt, small 1

14 Flat-head screw ST3.9 x 14 4

15 Drive pulley 1

16 Shaft end ring 1

17 Drive belt, large 1

18 Pulley frame 1

19 Washer 1

20 Screw M5 x 12 1

21 Left cover plate assembly 1

22 Wing nut (M6x50 Hex Head Bolt) 1

23 Wing nut (M6x45 Carriage Bolt) 1

24 Friction plate 2

25 Scraper blade 1

26 Auger 1

27 Auger axle 1

This product must be correctly assembled before use.

Handle (Fig. 1A)

Slide the lower section (C) into the upper section (B).

Line up the holes on each tube, and make sure the

cable (A) is clear of the mounting holes. Secure the two

sections together with the M6x45 carriage bolt and wing

nut.

Motor housing (Fig. 1B)

Remove the plug guard and connect socket (B) on the

upper cover (6) to the plug on the motor housing (7).

Secure the upper cover to the motor housing with the

ST4.2 x 30 Philips head self tapping screws.

ASSEMBLY

7

Model SN70016

Adjust knob (Fig. 1C)

Align the rib on the spindle with the notch on the adjust

knob and push the adjust knob onto the spindle. Secure

the knob with the ST4.2x50 Philips head self tapping

screw. Place the adjust knob cover onto the top and push

to secure into place.

Wheel (Fig. 1D)

Remove the screws and washers from the wheel bracket.

Install the wheels (13) and secure into place with the

washers and M5 x 12 screws. Push wheel covers into

place.

M6x45 Carriage

Bolt

B

C

A

Connecting the electrical cord (Fig. 3)

Loop the extension cord and feed it through the rear

handle. Rest the cord around the cord hook. This will

help prevent you from disconnecting the extension cord

from the product during operation.

WARNING: Do not handle the plug or the snow

thrower with wet hands or while standing in water.

DANGER: Electric shock can cause serious injury

or death.

8

Model SN70016

Wheel bracket (Fig. 1E)

Align the holes on the wheel bracket with the holes on

the upper cover. Secure into place with ST3.9x45 Philips

head self tapping screws in the two (2) top holes and the

ST3.9x55 Philips head self tapping screws in the two (2)

bottom holes.

Auxiliary handle (Fig. 2)

Position the auxiliary handle so that the holes are in

alignment with the holes in the handle support bracket.

Insert the M6X50 hex head bolt into the hex shaped bolt

hole of the bracket. Secure by tightening the wing nut

onto the bolt.

Loosen the wing nut and adjust the angle and height of

the handle to a safe and comfortable position. Secure

into place by tightening the wing nut onto the bolt.

M6x50 Hex

Head Bolt

2

3

ASSEMBLY

Clear snow often, before it gets too deep. It is best to

remove the snow as soon as possible after it falls.

Lift the auger up slightly before starting the snow thrower.

Switch on and tilt the snow thrower forward until the

scraper blade contacts the ground. Push the snow

thrower forward at a comfortable rate of speed, yet slow

enough to clear the path completely. The width and depth

of the snow determines your forward speed.

Pull up and turn the adjust knob to direct the snow to the

right or to the left. For the most efficient snow removal

throw the snow downwind and slightly overlap each

swath.

The snow thrower can remove up to 8” deep in one pass.

When clearing deeper drifts, hold the snow thrower by

the upper and lower handles and use a swinging or

sweeping motion. Shave off the top layer and make

multiple passes. (Fig. 6).

OPERATING

9

Model SN70016

This snow thrower is intended to be used to sweep snow

from sidewalks, steps, patios, decks and other hard flat

surfaces such as paved driveways. Use it only on hard,

flat surfaces free of sand, stone and debris, wires or any

other objects. The manufacturer is not liable for any

damage or injury resulting from misuse.

On/Off Switch (Fig. 4)

WARNING: The auger starts rotating immediately

after the snow thrower is switched on. Keep hands

and feet away from the auger.

To switch ON, hold the snow thrower firmly with two

hands, make sure the auger is not touching any surface

and press the Safety Lock Off Button (2) while squeezing

the On/Off trigger switch (3).

Once the snow thrower is started you can release the

Safety Lock Off Button.

To switch Off simply release the trigger.

Removing snow

WARNING: Before starting work, make sure that

the area to be cleared is free of stones, debris,

wires and any other objects.

Make sure all fasteners on the snow thrower (screws,

nuts, etc.) are fully tightened.

Check the auger for wear and tear at regular intervals.

Position the snow thrower so that snow will discharge in

a safe direction away from the operator and bystanders.

6

Correct

Incorrect

5

4

8”

For large areas a definite pattern of operation is required

to thoroughly clean an area of snow. These patterns

will avoid throwing snow in unwanted places as well as

eliminating a second removal of snow. (Fig. 7)

Pattern A: Throw the snow to the right or left side where

it is possible. For areas such as a long driveway it is

advantageous to start in the middle. Plow from one end

to the other, throwing snow to both sides.

Pattern B: If the snow can only be thrown to one side of

the area to be cleared, start on the opposite side.

Scraping the snow all the way down to the pavement will

wear out the scraper and auger. To protect these parts,

one or two inches of snow can be left behind and cleared

with de-icing salt or a shovel.

After clearing the snow, continue to run the snow thrower

for a few minutes to prevent ice from freezing on moving

parts. Then switch off the motor, wait for all moving parts

to stop, and wipe the ice and snow from the snow thrower

with a clean rag.

WARNING: To avoid serious personal injury, do not

use hands or feet to unclog the chute.

The snow thrower is equipped with a thermal safety

switch that will automatically shut off the motor in the

event the motor overheats. Should this occur, unplug

the unit and wait for the motor to cool down. This should

take about two minutes. The switch will reset itself after

the motor has cooled down and you can resume normal

operation.

10

Model SN70016

7

OPERATING

Regular cleaning and maintenance of your snow thrower

will ensure efficiency and prolong the life of the product.

After each use, take apart and clean out the ice and

debris from the ventilator and its slots, the auger and

the housing.

Only use a cloth soaked with hot water and a soft brush

to clean the snow thrower. Never wet or spray water on

the machine!

Do not use detergents or solvents as these could cause

irreparable damage to the snow thrower. Chemicals can

destroy the plastic parts.

To protect the snow thrower from corrosion when storing

for long periods, lightly oil the metal parts.

Store the appliance in a dry area out of reach of children.

For the user’s safety, worn or damaged parts must be

replaced. Replace with original replacement parts only.

Parts from another snow thrower may not fit properly

causing an unsafe situation.

Changing the belt (Fig. 8, 9)

The drive belts (17) and (13) need to be replaced when

worn.

Drive Belt (17)

1. Remove screws and take off the cover (21) and

friction plate (24).

2. Remove screw (20), washer (19), pulley frame (18),

and the belt (17) from the pulleys.

3. Install the new belt in the same groove as the old

one.

4. Replace the screw (20), washer (19) and pulley

frame (18).

5. Replace the cover (21) and friction plate (24). Secure

with screws.

Drive Belt (13) small

1. Repeat steps 1 and 2 above.

2. Remove screws (14) and remove the drive shaft (12)

and drive belt (13).

3. Install new belt (13) with the drive shaft (12).

4. Secure with screws (14).

5. Replace belt (17), screw (20), washer (19) and pulley

frame (18).

6. Replace the cover (21) and friction plate (24). Secure

with screws.

Before carrying out maintenance operations, disconnect power supply.

11

Model SN70016

8

9

21

7

17

18

19

24

12

13

14

20

MAINTENANCE AND STORAGE

Auger (Fig. 8, 10)

CAUTION Check fasteners before each use. A

loose auger can result is excessive vibration and

damage the snow thrower.

To replace the auger:

1. Remove cover (21) and friction plate (24). Remove

screw (20), washer (19), pulley frame (18), and the

belt (17).

 Loosen the nut (9) from the other side of the auger

(26) and dismount the pulley (15) and auger axle

(27).

 Replace the auger with a new one.

4. When reassembled ensure all screws and nuts are

properly tightened.

Scraper blade (Fig. 11)

The scraper blade is a wear item and should be replaced

when necessary. A worn scraper blade can cause

extreme vibration and damage the auger.

To replace the scraper blade:

1. Remove the three screws from the bottom of the

blade and slide the blade forward to remove.

2. Install new scraper blade.

3. Secure with the three screws.

4. Ensure the screws are properly tightened.

12

Model SN70016

10

11

16

15

27

26

10

9

1XM8

25

MAINTENANCE AND STORAGE

Problem Possible causes Remedy

Motor does not start Unit not plugged in.

No electricity.

Defective cable.

Plug in the unit.

Check power supply.

Check cable. Repair or replace if required.

Poor results Drive belt worn or damaged.

Auger worn or damaged.

Discharge blocked.

Replace the drive belt.

Replace the auger. Ensure the screws and nuts are

properly tightened.

Switch off the snow thrower and clean the discharge.

Abnormal vibrations Drive belt worn or damaged.

Auger worn or damaged.

Scraper blade worn or damaged.

Replace the drive belt.

Replace the auger. Ensure the screws and nuts are

properly tightened.

Replace the scraper blade. Ensure the screws are

properly tightened.

CALL US FIRST !!

Call us first with questions about operating or maintaining your product at 1-800-633-1501

between 8:00 a.m. – 5:00 p.m. Eastern Standard Time, or get assistance on americanlawnmower.com.

13

Model SN70016

PARTS AND SERVICE

SERVICE

For parts or service, please call 1-800-633-1501 or visit us online at americanlawnmower.com. Be

sure to provide all relevant information when you call or visit.

REPAIR PARTS

Please record your serial number in the space provided below.

• NAME OF ITEM Snow Thrower

• MODEL NUMBER SN70016

• SERIAL NUMBER

TROUBLESHOOTING

Always mention the model number when ordering kits/items for this tool.

No. Kit/Item Number Description QTY

1

SN1416-AHK-1 Auxiliary Handle Kit

1

2

SN1416-AKK-1 Adjust Knob Kit

1

3

SN1416-WK-1 Wheel Kit

1

4

SN1416-WBK-1 Wheel Bracket Kit

1

5

SN1416-SB-1 Drive Belt

1

6

SN1416-RB-1 Small Belt

1

7

SN1416-SBK-1 Scraper Blade Kit

1

8

SN1416-AK-1 Auger Kit

1

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way，

Indianapolis, IN 46256

Phone 1-800-633-1501

www.americanlawnmower.com

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OWNER’S MANUAL

SN70016 16-IN Snow Thrower

WARRANTY POLICY

Two (2) year limited warranty on Earthwise outdoor power equipment.

Earthwise warrants to the original owner that each new product and service part is free from defects in materials

and workmanship and agrees to repair or replace any defective product or part for the warranty period as stated

above from the original date of purchase except for the conditions and circumstances listed below:

This warranty applies only to the original purchaser at

retail and may not be transferred.

Warranty applies if the product is used for personal,

household or family use. Warranty is void if product is

used for commercial, industrial or rental purposes.

Warranty does not include repairs necessary due to

operator’s abuse or negligence (including overloading

the product beyond capacity or immersion in water), or

the failure to assemble, operate, maintain or store the

product according to the instructions in the operator’s

manual.

This warranty is not transferable and

only applies to product sold directly

from an authorized retailer. This warranty

does not apply to any product, new or used, purchased

through unauthorized third-party channels.

ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL

LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT

FROM ANY DEFECT, FAILURE OR MALFUNCTION

OF THE PRODUCT IS NOT COVERED BY THE

WARRANTY. Some states do not allow the exclusion or

limitation on how long an implied warranty lasts, so the

above limitation may not apply to you.

Products sold damaged or incomplete, sold “as is”, or

sold as reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper

handling, improper assembly, incorrect voltage, improper

wiring, improper maintenance, improper modification or

the use of accessories and/or attachments not specifically

recommended is not covered by this warranty.

Expendable items that become worn during normal use

are not covered by the warranty.

Warranty does not cover damage caused by cold, heat,

rain, excessive humidity, corrosive environments and

materials, or other contaminants.

Warranty does not include installation, assembly or

normal adjustments explained in the owner’s manual.

The expense of delivering the product to the vendor and

the expense of returning the product or replacement parts

to the owner is not covered by the warranty.

The warranty does not cover normal deterioration of the

exterior finish, including but not limited to scratches,

dents, paint chips or any corrosion or discoloration

caused by heat, abrasive and chemical cleaners.

Proof of purchase, original dated sales receipt, must accompany all

warranty claims.

Rev. 06/06/2019

Modelo SN70016

MANUAL DEL OPERARIO

Sopladora de nieve de 406 mm (16 pulg.)

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE EL

FUNCIONAMIENTO, EL MONTAJE, LAS PIEZAS Y EL MANTENIMIENTO? IR A

AMERICANLAWNMOWER.COM O LLAME AL 1-800-633-1501 ENTRE LAS

8:00 AM Y LAS 5:00 PM, A DEL ESTE DE LOS ESTADOS UNIDOS.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y

seguridad para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el

manual del operario antes de usar este producto.

SÍMBOLOS

Algunos de los siguientes símbolos pueden aparecer en este producto. Tenga a bien estudiarlos y aprender su significado.

La adecuada interpretación de estos símbolos le permitirá operar el producto mejor y de manera más segura.

2

Modelo SN70016

Precauciones para su seguridad.

PRECAUCIÓN: Lea el manual de instrucciones y atienda las instrucciones se seguridad y advertencia.

PRECAUCIÓN: Retire el enchufe del tomacorriente de inmediato si el cable está dañado o cortado.

APAGUE la máquina, espere hasta que se detenga por completo y retire el enchufe del tomacorriente

antes de realizar alguna tarea de mantenimiento, limpieza o reparación.

PRECAUCIÓN: Use siempre protecciones para sus ojos y oídos.

Use calzado seguro, resistente y antideslizante.

¡PELIGRO! Pueden ser lanzados objetos a gran velocidad cuando el motor está en funcionamiento. No

pase delante de la máquina cuando está funcionando.

Mantenga a las personas que se encuentran en el lugar a una distancia segura.

Mantenga el cable eléctrico lejos de la barrena. La barrena puede dañar el cable y producir un contacto con

piezas activas.

¡PELIGRO! Cuchillas giratorias. Mantenga manos y pies a una distancia segura.

No colocar la mano debajo de la barrena.

No colocar la mano enfrente del deflector de descarga.

No colocar la pie debajo de la barrena.

¡PELIGRO! Riesgos de descargas eléctricas.

No usar en la lluvia. No usar durante tormentas eléctricas.

Por favor tenga en cuenta que los cambios o modificaciones a los que se someta este producto y que no estén

expresamente aprobados por la parte responsable del cumplimiento, podrían anular la autoridad del usuario para

operar el equipo.

NOTA: Este equipo ha sido probado y se ha determinado que cumple con los límites de un dispositivo digital Clase B,

de conformidad con la Parte 15 de las Reglas de la Comisión Federal de Comunicaciones (FCC por sus siglas en

inglés). Estos límites están diseñados para brindar una protección razonable contra interferencias dañinas en

instalaciones residenciales. Este equipo genera, utiliza y puede emitir energía de radiofrecuencia, y si no se instala

y utiliza según las instrucciones, podría ocasionar interferencia perjudicial para las comunicaciones por radio. Sin

embargo, no se garantiza que no se producirá interferencia en alguna instalación en particular. Si este equipo causa

interferencia perjudicial a la recepción de radio o de televisión, lo cual puede determinar si apaga y enciende el equipo,

se le aconseja al usuario que trate de corregir la interferencia realizando una o más de las siguientes acciones:

-- Cambie la ubicación o la orientación de la antena receptora.

-- Aumente la distancia que separa el equipo y el receptor.

-- Conecte el equipo a un tomacorriente que esté en un circuito distinto al que está conectado el receptor.

-- Consulte a su concesionario o a un técnico experimentado de radio/TV para pedir ayuda.

Este dispositivo cumple con la Parte 15 de las Reglas de la Comisión Federal de Comunicaciones (FCC por sus siglas

en inglés). El funcionamiento del dispositivo está sujeto a las siguientes dos condiciones: (1) es posible que este

dispositivo no cause interferencia perjudicial, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluso

la interferencia que podría causar un funcionamiento no deseado.

Los productos eléctricos no se deben desechar junto con los residuos domésticos. Recicle donde haya

centros para tal fin. Consulte a la autoridad local o al distribuidor minorista para obtener asesoramiento

sobre reciclado.

PARA REDUCIR EL RIESGO DE LESIONES: Antes

de utilizar este producto, cerciórese de que todos los

usuarios lean y comprendan las instrucciones

de seguridad y la demás información incluida en

este manual.

PRECAUCIÓN: Use protección auditiva apropiada

mientras trabaja. En ciertas condiciones y con cierta

duración de uso, el ruido generado por este producto

puede contribuir a la pérdida de la audición.

Guarde estas instrucciones y revíselas con

frecuencia antes de usar la herramienta y para

impartirlas a otros.

ADVERTENCIA: Al utilizar aparatos eléctricos,

se recomienda respetar siempre las precauciones

de seguridad básicas que se detallan a continuación,

a fin de reducir riesgos de incendios, descargas

eléctricas y lesiones personales.

LEA TODAS LAS INSTRUCCIONES

CONTROLE SI HAY PIEZAS DAÑADAS. Antes de

seguir usando el producto, se deberán revisar las

piezas dañadas en forma exhaustiva para

determinar si la herramienta funcionará

correctamente y realizará el trabajo previsto.

Compruebe la alineación y las uniones de las

piezas móviles, el montaje, averías de componentes

y otros factores que puedan afectar el

funcionamiento. Se debe reparar o reemplazar

cualquier pieza dañada en forma adecuada. Para

recibir asistencia, comuníquese con nuestra línea

de ayuda de atención al cliente al 1-800-633-1501.

EVITE AMBIENTES PELIGROSOS. No utilice este

producto en condiciones de lluvia o tormenta.

Tampoco trabaje en entornos donde existan gases

o sustancias explosivas. Por lo general, los motores

de estos productos producen chispas que podrían

inflamar los gases.

MANTENGA ALEJADOS A LOS NIÑOS. Todos los

visitantes, niños y mascotas deben mantenerse a

una distancia segura de la zona de trabajo.

USE ROPA ADECUADA. No use prendas sueltas

ni artículos de joyería. Use protección para cubrir y

sujetar el cabello largo, ya que puede quedar

atrapado en las piezas móviles.

Utilice botas de goma al operar el quitanieves.

En todo momento mantenga una buena base de

apoyo, especialmente en pendientes.

USE GAFAS DE SEGURIDAD. Al trabajar con este

producto, use gafas de seguridad con protectores

laterales que cumplan con la norma ANSI Z87.1.

DOBLE AISLAMIENTO. La sopladora de nieve tiene

doble aislamiento. Es decir que todas las piezas

metálicas externas están aisladas del suministro

eléctrico. Esto se logra con la introducción de una

capa de aislamiento entre las piezas eléctricas y las

mecánicas. El doble aislamiento garantiza la mayor

seguridad posible.

ADVERTENCIA: Para el exterior, use cables de

extensión rotulados con las siguientes inscripciones:

SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A,

o SJTOWA. Estos cables están especificados para

usar al aire libre y reducir el riesgo de descarga

eléctrica.

ENCHUFES POLARIZADOS. Para reducir el riesgo

de descarga eléctrica, este producto tiene un enchufe

polarizado. Las conexiones polarizadas encajan de

una sola manera. Cerciórese de que el extremo del

receptáculo del cable de extensión tenga ranuras de

anchos diferentes para los contactos. Invierta el

enchufe si no encaja totalmente en el cable de

extensión. Si aún así no encaja, consiga un cable de

extensión adecuado. Si el cable de extensión no se

adapta bien al tomacorriente, llame a un electricista

competente para que instale un tomacorriente

adecuado. No modifique el enchufe de la herramienta

ni el cable de extensión de ningún modo.

CABLE DE EXTENSIÓN. Asegúrese de que el cable

de extensión esté en buenas condiciones. Además,

compruebe que tenga el grosor suficiente para

transportar la corriente que necesitará el producto.

Un cable de extensión muy pequeño provocará una

disminución en la tensión de la línea y, como

resultado, una pérdida de potencia y recalentamiento.

La siguiente tabla muestra el tamaño correcto que se

debe usar según la longitud del cable y el amperaje

de la etiqueta. Ante la duda, utilice el siguiente calibre

más grueso. Cuanto más bajo es el número de

calibre, más grueso es el cable.

Es posible unir dos cables de extensión con

un nudo para evitar que se

desconecten durante el uso. Realice

el nudo como se muestra en la

imagen y luego conecte el enchufe

del cable de alimentación en el

receptáculo del cable de extensión.

ADVERTENCIA: Mantenga todas las conexiones

secas y alejadas del suelo. No toque el enchufe

con las manos mojadas.

Tenga presente el cable de extensión mientras

opera la sopladora de nieve. Tenga cuidado de

no tropezar con el cable y siempre manténgalo

alejado de la barrena.

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

NORMAS GENERALES DE SEGURIDAD

3

Modelo SN70016

Calibre mínimo para los cables

Voltios Longitud total del cable en pies

120V 0-25 26-50 51-100 101-150

Amperaje

Más de No más de Calibre AWG

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 No se recomienda

NO FUERCE EL QUITANIEVES - Funcionará

mejor y de manera más segura a la velocidad para

la que fue diseñado.

PRECAUCIÓN: Nunca arroje nieve a las personas,

mascotas o automóviles y no permita que nadie

esté frente a la sopladora de nieve mientras está

en funcionamiento.

Los objetos que pueden tapar la sopladora de

nieve o causar daños pueden estar escondidos en

la nieve. Antes de usar la máquina, despeje el área

de felpudos, trineos, tablas, cables y otros

desechos.

Si la barrena golpea un cuerpo extraño, verifique

que no haya signos de daños en la sopladora de

nieve y haga las reparaciones necesarias antes de

volver a empezar y continuar el trabajo.

PONGA ATENCIÓN. Ponga atención a lo que está

haciendo. Use el sentido común. No opere la

sopladora de nieve si está cansado o bajo la

influencia de drogas, alcohol o medicamentos.

Si la sopladora de nieve comienza a vibrar de

manera inusual, apáguela de inmediato y revísela

para detectar la causa. Generalmente, la vibración

advierte la existencia de un problema.

Siempre apáguela; desconéctela del suministro

eléctrico y espere hasta que la barrena se detenga

por completo antes de realizar tareas de

mantenimiento o reparaciones.

No utilice el quitanieves en superficies cubiertas

con gravilla a menos que se haya ajustado para

tales superficies, según el manual del operario.

El funcionamiento del quitanieves en posición

manual no es seguro a menos que se utilice

conforme a las instrucciones especiales provistas

en el manual del operario.

PRECAUCIÓN: La barrena no se detiene de

inmediato cuando se apaga la sopladora de nieve.

PRECAUCIÓN: Riesgo de lesiones. No acerque

ninguna parte de su cuerpo, ni prendas de vestir a

la barrena giratoria.

ADVERTENCIA: Proposición 65 de California:

Este producto contiene sustancias químicas al

estado de California como causantes de cáncer,

defectos de nacimiento u otros problemas

reproductivos .

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

NORMAS GENERALES DE SEGURIDAD

4

Modelo SN70016

INTERRUPTOR DE CIRCUITO POR FALLA A

TIERRA (ICFT). El circuito o tomacorriente que se

usen para la sopladora de nieve deben contar con

esta protección. Se pueden utilizar receptáculos que

tengan la protección de ICFT incorporada.

ADVERTENCIA: Mantenga las manos lejos de las

piezas en movimiento. Nunca coloque las manos

cerca de la barrena para quitar nieve, palos u otro

desecho. Al limpiar la barrena, esta puede

destrabarse repentinamente y provocar lesiones,

aún cuando la sopladora de nieve se haya detenido.

Para destapar, use siempre un palo de madera

como el del mango de una escoba.

DESCONECTE LA UNIDAD del suministro eléctrico

cuando no esté en uso o durante el servicio de

mantenimiento o la limpieza. Manténgala bajo

vigilancia constante.

NO MALTRATE EL CABLE. Nunca tire del cable

para trasladar este producto ni para desconectarlo

del receptáculo. Aleje el cable del calor, el aceite y

los bordes filosos.

USE LA HERRAMIENTA CORRECTA. No utilice

este producto en trabajos para los que no esté

indicado.

NO SOBRECARGUE la sopladora de nieve

usándola a una velocidad excesiva.

NO ADOPTE UNA POSTURA INCÓMODA.

Guíe la sopladora de nieve sólo a paso de hombre.

Mantenga una base de apoyo firme y buen

equilibrio en todo momento.

ILUMINACIÓN. Trabaje con la sopladora de nieve

sólo con luz natural o buena luz artificial.

GUARDE LA UNIDAD BAJO TECHO. Cuando no

esté en uso, la sopladora de nieve se deberá

guardar en un lugar seco, fuera del alcance de

los niños.

MANTENGA LA UNIDAD EN CONDICIONES.

Consérvela limpia para lograr un óptimo

funcionamiento y reducir el riesgo de lesiones.

Revise el cable de extensión periódicamente y

reemplácelo si está dañado. Mantenga los mangos

secos, limpios y libres de aceite.

Para un funcionamiento seguro, no utilice la

sopladora de nieve en pendientes demasiado

pronunciadas. Cuando trabaje en pendientes,

disminuya la velocidad y asegúrese de tener una

buena base de apoyo.

Antes de arrancar la sopladora de nieve, asegúrese

de que la barrena no toque ningún objeto y esté

libre para moverse.

EVITE EL ENCENDIDO ACCIDENTAL. No

transporte el cortasetos enchufado, con el dedo en el

interruptor. Asegúrese de que el interruptor esté en la

posición de apagado al enchufar el cable de la

herramienta.

ESPECIFICACIONES DEL PRODUCTO

Modelo: SN70016

Voltaje del suministro eléctrico: 120 V - 60 HZ

Velocidad de ralenti: 4500 RPM

Consumo: 12 amperios

Peso: 6.6 kg (14.5 libras)

5

Modelo SN70016

Ancho de barrido: 406 mm (16 pulg.)

Profundidad máx. de barrido: 200 mm (8 pulg.)

Distancia de lanzamiento: Hasta 9.14 m (30 pies)

Capacidad de barrido: 195 kg (430 libras)/minuto

DESEMBALAJE

Extraiga la herramienta de la caja con cuidado.

Asegúrese de que estén incluidos todos los

elementos detallados en la lista de embalaje.

Inspeccione el producto detenidamente para

corroborar que no existan roturas ni averías

ocurridas durante el envío.

No deseche el material de embalaje hasta

haber inspeccionado exhaustivamente el

producto y comprobar que funciona en forma

satisfactoria.

Si alguna pieza falta o está dañada, llame al

1-800-633-1501 para obtener asistencia.

LISTA DE EMBALAJE

1 Sopladora de nieve

1 Mango inferior y el mango superior

1 Perno de carruaje (6 x 45) y tuerca de mariposa

4 Tornillo autorroscante (4,2 x 30)

1 Perilla de ajuste

1 Tornillo autorroscante (4,2 x 50)

1 Tapa de la perilla de ajuste

1 Soporte de ruedas

2 Ruedas

2 Cubierta de ruedas

2 Tornillo autorroscante (3,9 x 45)

2 Tornillo autorroscante (3,9 x 55)

1 Mango auxiliar

1 Perno de cabeza hexagonal (6 x 50) y tuerca de mariposa

1 Manual del operario

LISTA DE PIEZAS

6

Modelo SN70016

Pos. Description Qty

1 Enchufe 1

2 Botón de bloqueo de seguridad 1

3 Interruptor del gatillo de encendido/apagado 1

4 Mango 1

5 Mango auxiliar completo 1

6 Cubierta superior 1

7 Caja del motor 1

8 Perilla de ajuste 1

9 Tuerca ciega M8 1

10 Arandela elástica 1

11 Deflector 3

12 Eje de accionamiento 1

13 Correa de transmisión, pequeña 1

14

Tornillo de cabeza plana ST3.9 x 14

4

15 Polea de mando 1

16

Anillo de extremo de eje

1

17 Correa de transmisión 1

18 Soporte de la polea 1

19 Arandela 1

20 Tornillo M5 x 12 1

21 Cubierta, izquierda 1

22 Tuerca de mariposa (M6 x 50) 1

23 Tuerca de mariposa (M6 x 45) 1

24

Placa de fricción

2

25 Cuchilla raspadora 1

26 Barrena 1

27 Eje de la barrena 1

1

3

2

4

6

22

5

23

8

9 10

11

12

13

14

15

16

17

18

19 20

21

24

25

26

27

7

La page charge ...

EarthWise SN70016 Le manuel du propriétaire

EarthWise SN70016 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents