Paramount EF-WM373 MO Guide d'installation

Page 108.16.16

1

YEAR

limited

WARRANTY

Wall Mount Fireplace

With Adjustable Mounting Bracket

Owner’s Manual

Model Number Item Number

JR42 EF-WM353 MO (42”)

JR50 EF-WM350 MO (50”)

JR60 EF-WM349 MO (60”)

JR72 EF-WM348 (72”)

*Patented Flame Technology & Front Venting Design

READ & SAVE THESE INSTRUCTIONS

Carefully read and review before assembling, installing, operating, or maintaining

this product. Observe all safety instructions and information.

FAILURE TO FOLLOW WARNINGS & OPERATIONAL INSTRUCTIONS CONTAINED IN THIS

MANUAL CAN RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY

**IMPORTANT NOTICE**

For customer service & warranty issues, please contact: [email protected]

Page 2 08.16.16

Introduction

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance

accordingtooperatinginstructionscouldcausereorinjury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before servicing. To

disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young

children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are

at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep

toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothingorotherammablematerialshouldnotbeplacedonorneartheappliance.

• Duetohightemperatures,theapplianceshouldbelocatedoutoftrafcandawayfromfurnitureanddraperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot

surfaces.Thesescreensandguardsmustbefastenedtotheoor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance and are kept

clean.Theapplianceshouldbeinspectedbeforeuseandatleastannuallybyaqualiedserviceperson.More

frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area

mustbekeptclearandfreefromcombustiblematerials,gasolineandotherammablevaporsandliquids.

• Undernocircumstancesshouldthisappliancebemodied.

• Donotusethisapplianceifanyparthasbeenunderwater.Immediatelycallaqualiedservicetechniciantoinspect

the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be

donebyalicensedorqualiedserviceperson.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic

bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been dropped or

damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical

adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from

trafcareaandwhereitwillnotbetrippedover.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric

shockorre,ordamagetheappliance.

• Topreventapossiblere,donotblockairintakesorexhaustinanymanner.Donotuseonsoftsurfaces,likea

carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap

(outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to

decorations, a T.V. or other electronic components.

Page 308.16.16

Dimensions

Listing Approvals

FRONT VIEW

TOP VIEW

SIDE VIEW

ThisappliancehasbeentestedinaccordancewiththeCSAStandardsforxedandlocation-dedicated

electric room appliances in the United States and Canada. If you need assistance during installation, please

contact your local dealer.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or,

in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United

States or the Canadian Electric Code, CSA C22.1 in Canada.

PRODUCT DIMENSIONS CARTON DIMENSIONS

Item No. A B C D E F G Width x Depth x Height

EF-WM353 MO 42” 20” 4.2” 18.8” 36.10” 9.72” 31.97” 49” x 10.24” x 25.59”

EF-WM350 MO 50” 20” 4.2” 18.8” 44.10” 9.72” 39.72” 56.89” x 10.24” x 25.59”

EF-WM349 MO 60” 20” 4.2” 18.8” 54.10” 9.72” 50”

66.93” x 10.24” x 25.59”

EF-WM348 72” 23.25” 4.2” 20.27” 66.10” 10.24” 60”

74.80” x 6.5” x 25.28”

Item No. Net Weight Gross Weight

EF-WM353 MO 22 KGS 28 KGS

EF-WM350 MO 26 KGS 33.5 KGS

EF-WM349 MO 31 KGS 39 KGS

EF-WM 348 40 KGS 48 KGS

Description Electric Fireplace

Type 3 Way Mounting Wall Mount

Voltage 120V AC

Watts MAX 1500W

Amps 15 AMP Grounded Circuit

A

E

G

F

B

D

C

Page 4 08.16.16

General Instructions

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE IT

IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

1. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

2. Theappliancemayemitaslight,harmlessodourwhenrstused.Thisodourisnormalanditiscaused

by the initial heating of internal appliance elements and will not occur again.

3. If your appliance does not emit heat, consult the operation section of this manual for further information.

4. UsewithaCSAorULcertiedsurgeprotector.

5. Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in

manufactured homes when installed according to these instructions.

Aswithmostelectronicdevices,yournewelectricreplacehasbeendesignedtooperateat

temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the

replacetoreachroomtemperaturebeforeturningiton.

WARNING

Unpacking and Testing Appliance

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance

operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet.

Page 508.16.16

EF-WM353 MO (42”) x2

EF-WM350 MO (50”) x2

EF-WM349 MO (60”) x2

EF-WM348 (72”) x2

EF-WM353 MO (42”) x2

EF-WM350 MO (50”) x2

EF-WM349 MO (60”) x2

EF-WM348 (72”) x2

EF-WM353 MO (42”) x2

EF-WM350 MO (50”) x2

EF-WM349 MO (60”) x2

EF-WM348 (72”) x2

EF-WM353 MO (42”) x1

EF-WM350 MO (50”) x1

EF-WM349 MO (60”) x1

EF-WM348 (72”) x1

EF-WM353 MO (42”) x1

EF-WM350 MO (50”) x1

EF-WM349 MO (60”) x1

EF-WM348 (72”) x1

EF-WM353 MO (42”) x8

EF-WM350 MO (50”) x8

EF-WM349 MO (60”) x26

EF-WM348 (72”) x32

EF-WM353 MO (42”) x1

EF-WM350 MO (50”) x1

EF-WM349 MO (60”) x1

EF-WM348 (72”) x1

EF-WM353 MO (42”) x9

EF-WM350 MO (50”) x13

EF-WM349 MO (60”) x13

EF-WM348 (72”) x16

EF-WM353 MO (42”) x9

EF-WM350 MO (50”) x13

EF-WM349 MO (60”) x13

EF-WM348 (72”) x16

EF-WM353 MO (42”) x1

EF-WM350 MO (50”) x1

EF-WM349 MO (60”) x1

EF-WM348 (72”) x1

EF-WM353 MO (42”) x4

EF-WM350 MO (50”) x4

EF-WM349 MO (60”) x4

EF-WM348 (72”) x4

EF-WM349 MO (60”) x6

EF-WM348 (72”) x8

EF-WM349 MO (60”) x6

EF-WM348 (72”) x8

F- Drywall AnchorsD- Mounting Bracket

L- Cord Cover

E- Wood Screws

A- Fireplace B- Side Brackets

OPTIONAL

For kit of OPTIONAL

parts J, K, L

(Item No: EF-WC)

contact:

1-800-561-5550

OPTIONALOPTIONAL

C1 - Top/Bottom Brackets C2 - Top/Bottom Brackets

G- ST4x12 Metal Screws

I- Crystals

J- Cord Corner K- Cord Corner

H- Remote Control

Hardware Parts List

Page 6 08.16.16

Locating Appliance

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36” FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

WARNING

This appliance is for use on 120 Volts. The cord

has a plug as shown in (A). An adapter as shown

in (C) is available for connecting three-blade

grounding type plugs to two-slot receptacles. The

green grounding lug extending from the adapter

must be connected to a permanent ground such

as a properly grounded outlet box. The adapter

should not be used if a three-slot grounded

receptacle is available.

To disconnect appliance, turn controls to off, then

remove plug from outlet.

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

GROUNDING METHODS

Grounding Appliance

Page 708.16.16

Installation

Minimum Clearance to Combustibles

Minimum Mantel Clearances

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE

CORD TO AVOID TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

PERSONAL INJURY. DO NOT RUN CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW

RUGS, RUNNERS OR THE LIKE. ARRANGE CORD AWAY FROM TRAFFIC AREAS AND WHERE IT

WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY

MANNER. DO NOT USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED

OPTIONAL ACCESSORIES. USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR

THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE

GASOLINE OR OTHER FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY

CREATE A FIRE HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

WARNING

Your JR42/50/60/72 unit is a wall-mounted appliance. Select a suitable location that is not susceptible to

moistureandisawayfromdrapes,furnitureandhightrafcareas.

NOTE: Follow all National and local electrical codes.

Bottom

Sides

Back

0”

Top

Measurements are taken from the glass front

8” (203mm) to mantel

8” (203mm) to ceiling

Page 8 08.16.16

No Recess:

- Easy installation

- Full use of backlight

- Easy maintenence

For installation

instructions refer

to Page 12

Adjustable Mounting Brackets and Installation Options

Full Recess:

- Flush to wall look

- No use of backlight

For installation

instructions refer

to Page 9

Partial Recess:

- 1” gap for multi-use

- No use of backlight

- Easy maintenence

For installation

instructions refer

to Page 9

FIG. 2

SIDE

VIEW

TOP

VIEW

PARTS

NEEDED

FIG. 3 FIG. 4

NOTE:Itisrecommendedthatthewallsfortheapplianceenclosurebenished(ie.drywall)to

avoid exposed insulation or vapour barriers coming in contact with the appliance. This will ensure

clearance to combustibles is maintained.

OPTION 1 OPTION 2 OPTION 3

B + C1 or C2

(JR42/JR50: B only) (JR42/JR50: B only)

B + C1 or C2D

Page 908.16.16

Option 1: Recessing the Appliance Flush into the Wall

Duetothemanydifferentnishmaterialsusedonwalls,itishighlyrecommendedthatyouconsultyourlocal

builder before you install this appliance in the wall.

Select a location that is not prone to moisture and is located at least 36” (914mm) away from combustible

materials such as curtain drapes, furniture, bedding, paper etc.

C1 or C2

B

1. Measure the appliance and create a rough in

with electrical.

2. Remove the front glass (refer to Page 15 for

instructions).

3. Remove the LED back lights (refer to Page 16

for instructions).

4. Holdtheapplianceuptoensureitwilltintothe

framing.

5. To fully recess the appliance into the wall:

A. Position and screw the side Builder’s

brackets (shown in grey on Page 10) to the set

of holes closest to the front glass as in Figure 2

on Page 8.

B. Use 8-24 screws (provided) to lock appliance

into wall from the side facing out.

C. Install the media and reinstall the glass front.

6. To partially recess the appliance into the

wall (Option 3):

A. Position and screw the side Builder’s

brackets (shown in grey on Page 10) to the

second set of holes from the front glass as in

Figure 4 on Page 8.

B. Use 8-24 screws (provided) to lock appliance

into wall from the side facing out.

C. Install the media and reinstall the glass front.

NOTE: Two sets of holes are provided for

recessing into the wall. The wall structure

may limit how far the appliance can be

recessed. Use the appropriate set of holes

when recessing to the frame, it may be

necessary to use the four holes on the top

and bottom.

FRONT VIEW

Page 10 08.16.16

Positioning of Adjustible Builder’s Brackets

EF-WM353 MO,

EF-WM350 MO

EF-WM349 MO

Builder’s bracket positions

shown in grey for each model

EF-WM348

B: Side brackets

C1: Top bracket (Tall)

Use for more security & surface area

C2: Top bracket (Short)

Usedwhennowallnishisapplied.

Will stay hidden behind glass.

B

C2

Page 1108.16.16

Minimum Clearance to Combustibles

Framing

Sides, back and top 0”

Measurements are taken from the glass front

Item No. A C D EB

EF-WM353 MO

EF-WM350 MO

EF-WM349 MO

EF-WM348

Recommended Framing Dimensions

Finishing Material

(NON-LOAD

BEARING)

A

B

19.3” (49cm) 38.60” (98cm)

19.3” (49cm) 46.60” (118.4cm)

19.3” (49cm) 56.60” (143.8cm)

21.27” (52.8cm) 68.60”

4.2”

18.8”

36.10”

44.10”

54.10”

66.10” (174.2cm)

NOTE to installer: Please allow extra clearance for the power cord and easy installation.

TOP VIEWSIDE VIEW

E

D

C

Page 12 08.16.16

Option 2: Hanging the Appliance on the Wall

Due to the many different materials used on different walls, it is highly

recommended that you consult your local builder before you install this

appliance on the wall.

1. Select a location that is not prone to moisture and is located at

least 36” (914mm) away from combustible materials such as curtain

drapes, furniture, bedding, paper, etc.

2. Have two people hold the appliance against the wall to determine the

location.

3. Remove the bracket from the back of the unit by removing the two

screws, refer to Figure 1.

4. Mark out location, then mount the bracket onto the wall using the 8

supplied screws. This bracket MUST have the hooks facing upward

and be level.

WALL MOUNT

BRACKET

SCREWS

HOOK

NOTE: It is strongly recommended

that the mounting bracket be

screwed into the wall studs where

possible. If the wall studs cannot

be used, ensure that the supplied

plastic anchors are used to

the

bracket to the wall and the bracket

is adequately secured.

5. With the wall mounting bracket installed have two people lift the appliance up and insert the two

hooks on the bracket into the two slots on the back of the appliance.

6. Check the appliance for stability ensuring that the bracket will not pull free from the wall.

BODY

FRONT

GLASS

SIDE VIEW

Figure 1

Bracket

Page 1308.16.16

1. Remove the cover plate from the right side of the appliance by removing the four screws, as shown above.

2. Remove the wire connectors from the power cord. The power cord may be discarded.

3. Take the new cover plate, supplied in the manual bag. Punch out the 7/8” (22mm) hole and install a box

connector through, into the junction box. Snap the box connector clamp onto the supply wires.

4. Using the wire connectors, connect the ground green wires (G) and white wires (N) together, then hot

black wires (L) and then refer to Figure 2.

5. Reinstall the cover plate using the four screws, as shown in Figure 1.

NOTE: Leave enough wire so that the appliance can be removed from the enclosure without

disconnecting the power supply.

HARD WIRING CONNECTION

Ifitisnecessarytohardwirethisappliance,aqualiedelectricianmustremovethecordconnection,and

wire the appliance directly to the house hold wiring.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In

the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

COVER PLATE

Figure 1

Figure 2

Hard Wiring Installation

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

WARNING

G

N

L

Page 14 08.16.16

Wall Thermostat Installation

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

WARNING

NOTE:Wirethewallthermostatpriortoinstallingthereplace.

WALL THERMOSTAT WIRING (24VAC)

1. Turn off circuit breaker.

2. Remove cover palte located on the left side of the appliance.

3. Pull the wire out and cut the inside thermostat. Connect the wires to the wall thermostat as shown below.

Follow instructions provided with wall switch kit.

5V

INSIDE OUTSIDE

BLACK

THERMOSTAT

WALL THERMOSTAT

Page 1508.16.16

1. Remove the 4 screws from the sides of the appliance in Figure 1.

2. Have two people lift the glass up and away from the appliance, holding the glass vertical while carrying.

Carefully rest the glass on a soft, non-abrasive surface.

3. Install the crystal embers (refer to instructions on Page 16)

4. Re-install the front glass by aligning the slots with the pins on the side of the appliance. Press the glass

down to secure in place.

5. Secure the front glass using the 4 screws in Figure 1. (If fully recessed, this is not necessary)

Front Glass Removal / Installation

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

BEFORE THE FRONT GLASS IS INSTALLED OR REMOVED, UNPLUG THE APPLIANCE AND WAIT UNTIL

APPLIANCE IS COOL TO THE TOUCH. GLASS CAN BE HEAVY AND FRAGILE SO HANDLE WITH CARE.

WARNING

FinishingFinishing

Figure 1

Page 16 08.16.16

The glass front must be removed and the appliance must be secured in its location before the crystal

embers are installed.

1. Carefully place crystal embers into the bottom media tray on the front of the appliance as illustrated.

Apply an even layer from side to side.

LED Back Light Removal

The glass front must be removed and the appliance must be secured in its location before the crystal

embers are installed.

1. Unscrew the two screws in Figure A.

2. Lift off the LED cover and remove.

3. Disconnect the wires where connected to the circuit board. The disassembly is complete.

your unit the most exquisite and stylish look. To order our Diamond Embers, contact our toll-free customer

service at 1-866-592-6667.

Crystal Embers Installation

Page 1708.16.16

Main Power Switch

Operating with Touch Panel

Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.

NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power

failure, the appliance will lose its memory function and will reset to factory mode when the power

returns.

To turn unit power on:

1. Plug in power cord.

2. Turn on the power switch (located on the front bottom right side of the appliance).

3. Verify the power is turned on when two ring tones are initiated.

The unit can be controlled by either the touch panel controls which are located on the right side of the front

glass or the remote control.

1. Press “ ” to turn on and off the appliance.

2. Press “ ” multiple times to adjust between mid, low, on/off, or high brightness options

3. Press “ ” multiple times to set operating duration to 30 min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h, or off.

4. Press “ ” multiple times to set ambient temperatures at 18°C, 19°C, 20°C, 21°C, 22°C, 23°C, 24°C,

25°C,26°C,27°C,28°C,ONorOFF.Whensettingthetemperature,thenumberwillash.

Note: The touch panel buttons will glow when pressed. The light fades in 5 seconds after pressing.

Operating Instructions

WHILE THE APPLIANCE IS OPERATING DO NOT REMOVE THE GLASS PANEL. THIS WILL CAUSE THE

REMOTE CONTROL AND TOUCH PANEL TO DISFUNCTION.

WARNING

ON/OFF

Power

Flame Timer Heater Indicator

Page 18 08.16.16

Multi-functional Operating with Remote Control

Turning ON/OFF the appliance:

1. Ensuresteps1-3inthe“MainPowerSwitch”procedurearerstfollowed.

2. Pressthe“”remotebuttontoturnonbothameandemberbedLEDs.

3. Pressthe“”buttonagaintoturnoffbothameandemberbedLEDS.

4. Verify the lights are shut off.

5. Turn off the main power swtich.

6. Unplug the power cord.

Note: The LEDs are at the brightest when the heating element is shut off. The

power swtich on the appliance must be turned on for the remote control to operate.

Changing the temperature:

1. Ensure steps 1-2 in “Turning ON/OFF the appliance” are previously followed.

2. Press the “ ” button to turn on the heat element to HIGH temperature at

1500W.

3. Press the “ ” button again to decrease the temperature to LOW temperature

at 750W.

4. Press the “ ” button multiple times to set ambient temperature to 18°C,

19°C, 20°C, 21°C, 22°C, 23°C, 24°C, 25°C, 26°C, 27°C, 28°C, ON or OFF. The

number will appear on touch panel display.

Note: Pressing the “ ”or “ ” a second time turns off the heating element.

Changing LED options:

1. Ensure steps 1-2 or 1-3 in “Turning ON/OFF the appliance” are previously

followed.

2. Pressthe“”buttontoturnonorofftheameandemberbedLEDs.

3. Press the “ ” button multiple times to cycle through 3 different brightness levels and OFF for the yellow

ameLEDs.

4. Press the “ ” button multiple times to cycle through 3 different brightness levels and OFF for the blue

ameLEDs.

5. Press the “ ” button multiple times to cycle through 3 different brightness levels and OFF for the pink

ameLEDs.

6. Press the “ ” button multiple times to set operating duration to 30min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h, or off.

7. Press the “ ” button multiple times to cycle the back LED lights through red, yellow, blue, red/blue, red/

yellow, yellow/blue, red/yellow/blue, fade, or OFF.

Note: Steps 2-7 can be done independently.

Page 1908.16.16

RemoteControlSpecications

Storage Instructions

1. MCU Chips: SN8P2722 Chip

2. Software: LRC 12-02

3. Remote: 10 key remote

4. Item No.: EF-WM353 MO, EF-WM350 MO,

EF-WM349 MO, EF-WM348

NOTE: Make sure your “AA” batteries (x2) are

fully charged and installed correctly in your

remote control before operating.

The remote control must remain within 5

meters or 17 feet of the appliance to be

effective, this range may be reduced when

battery power is depleted.

Maintenence

PREPARATION FOR MAINTENANCE

ALWAYS DISCONNECT THE POWER AND ALLOW THE ELECTRIC APPLIANCE TO COOL BEFORE

PERFORMING ANY CLEANING, MAINTENANCE OR RELOCATION OF THIS ELECTRIC APPLIANCE.

TURN CONTROLS TO OFF AND REMOVE PLUG FROM OUTLET OR TURN OFF THE HOUSE

CIRCUIT BREAKER TO ELECTRIC APPLIANCE RECEPTACLE.

DO NOT INSTALL REPLACEMENT BULBS THAT EXCEED SPECIFIED MAXIMUM WATTS.

THE BULBS IN YOUR APPLIANCE CAN BECOME EXTREMELY HOT. ALLOW AT LEAST

10 MINUTES BETWEEN TURNING OFF THE APPLIANCE AND REMOVING THE LAMPS TO AVOID

ACCIDENTAL BURNS.

DO NOT HANDLE THE BULBS WITH BARE FINGERS, OILS FROM YOUR SKIN WILL DAMAGE THE

BULS WHEN THEY HEAT UP. USE GLOVES OR A CLEAN DRY CLOTH WHEN HANDLING BULBS.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the

powercordisstoredorsecuredtoavoidtrippingorsnaggingtoreducetheriskofre,electricshock,or

injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other applicable

regulationstoreducetheriskofre,electricalshock,andinjurytopersons.

Donotattempttowireyourownnewoutletsorcircuits.Toreducetheriskofre,electricshock,orinjuryto

persons, always use a licensed electrician.

Page 20 08.16.16

_

+

[

LRC16 FR-4

2014/09/18

SHENGYI

+ EBY

FN

FIRE_Y

-N1

FN-N1

L_B

L_Y

R1

-N1

-L1

H1

H2

RF

SI1

IC2

R-N1

RELY-H1

C-FF

RELY-H2

C-FF

RELY-H

C-FF

1

E

2

FIRE_B

LE- H 

E

YB

+

BY

E

C

N2

CN1

+

E

B

Y

+

E

B

Y

Y

Y2

Y1

E

E2

E1

CN1

B

B2

B1

B11

B12

CN2

E11

E12

Y11

Y12

EN

CL

 

_

S

+

CL

SI1

CN2

CN1

CN2

CN1

-



EN

CL

1

2

G



F

G

C

E

+

CL

S

R8-1

FR-4

201/04/16

SHENGYI

CN2

E

I E

ER

FLE

Wiring Diagram

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

WARNING

FIRE ELEMENT

EMBER

BACKLIGHT 1

BACKLIGHT 2

BUTTON

POWER

CORD

SWITCH

RECEIVER

TEMPERATURE

SENSOR

HEATING ELEMENT

La page est en cours de chargement...

Paramount EF-WM373 MO Guide d'installation

Paramount EF-WM373 MO Guide d'installation

dans d''autres langues

Documents connexes

Autres documents