Matrox G450 MMS Manuel utilisateur

Catégorie
Cartes graphiques
Taper
Manuel utilisateur
www.matrox.com/graphics
Graphics Solutions for Professionals
User Guide
10807-301-0220
2007.02.02
Matrox
G450 MMS
ENGLISH
2 Matrox G450 MMS – User Guide
Overview
Thank you for purchasing a G450 MMS (Multi-Monitor Series) graphics card. Your Matrox MMS
card is a high-performance graphics card that plugs into an expansion slot inside your personal
computer. With this card, you can use 2 or 4 computer monitors or TVs at a time.
Hardware supplied
Software supplied (for Windows 2000/XP and NT 4.0)
!
Matrox PowerDesk
– to use your Matrox graphics hardware
!
Other software
– see the CD-ROM
Readme
file
Installation overview
To install your Matrox product:
1
Install the Matrox card – see “Hardware installation, page 3.
2
Install the software – see “Software installation, page 8.
G450 MMS card
*
* Pictured is a G450×4 MMS card.
Dual-monitor cable
2 dual-monitor cables are included with Matrox MMS×4 products.
DVI-to-HD15 adapters
2 DVI-to-HD15 adapters are included for each dual-monitor cable.
Note:
If your Matrox product is already partially or fully installed on your computer, some
or all the installation information in this guide may not apply to you. However, this
information may be useful if you need to reinstall your Matrox product.
Matrox G450 MMS – User Guide 3
Hardware installation
This section describes how to install your Matrox card. For information specific to your computer,
like how to remove its cover, see your system manual.
1 Switch to the standard VGA display driver
If youre running Windows 2000/XP on your computer, this step isnt necessary.
If youre using another operating system (for example, Windows NT 4.0), see its
documentation for how to switch to VGA mode.
2 Open your computer and
remove your existing graphics
card
*
If a graphics card
isn’t
already installed in
your computer, skip to step 3.
a
Using
Add/Remove Programs
in the
Windows
Control Panel
, remove any
currently installed display drivers.
Restart your computer for the changes
to take effect.
After your computer restarts, you’re
prompted to install drivers for the new
graphics hardware detected. Click
Cancel
.
WA R NI N G :
To avoid personal injury, turn off your computer, unplug it, and then wait for
it to cool before you touch any of its internal parts.
While your computer is turned off but still plugged in, some electrical current is supplied
to the motherboard. This current may prevent newly installed hardware from working
properly.
Also, static electricity can severely damage electronic parts. Before touching any electronic
parts, drain static electricity from your body (for example, by touching the metal frame of
your computer). When handling a card, carefully hold it by its edges and avoid touching its
circuitry.
* With multi-display mode, you may be able to use your existing graphics card. For Windows 2000/XP, see Windows 2000/XP
online help under “Multiple Display Support”. For Windows NT 4.0, only Matrox graphics card models supported by the Matrox
display driver can be used.
4 Matrox G450 MMS – User Guide
b
Turn off your computer and all peripherals such as your monitor or printer.
c
Open the computer and remove your existing graphics card. (If graphics hardware is
built into the motherboard of your computer, you may need to disable it manually. For
more information, see your system manual.)
3 Choose a PCI slot
Most computers have different types of
expansion slots. Choose a
PCI
(not
PCI
Express
) slot for your graphics card. Your
card supports both 64-bit and 32-bit PCI
slots. Your system manual should identify
the location of each type of expansion slot in
your computer.)
(Back of computer)
PCI
Express
slots
PCI
slots
AGP
slot
Note:
If youre using a PCI graphics card in a PCI 64-bit compatible slot, your choice of PCI
slot may affect your card or system performance. For more information, see your computer
manual.
WARNIN G:
Inserting your Matrox card
into the wrong type of slot could damage
your card, your computer, or both.
If youre using a 64-bit PCI slot, your
cards edge connector should be inserted
into only part of the PCI slot (the part
closest to the back of the computer).
AGP card
PCI card
PCIe card
32-bit
64-bit
Matrox G450 MMS – User Guide 5
4 Insert your Matrox card
a
Position your Matrox card over the
expansion slot youve chosen.
b
Push the card in firmly and evenly until
it’s fully seated in the slot.
c
Secure the bracket of your Matrox card
to the computer frame.
6 Matrox G450 MMS – User Guide
Connection setup
This section describes how to connect computer monitors to your Matrox product.
1 Connect your dual-monitor
cables
Attach your Matrox dual-monitor cables
*
to
the connectors on the bracket of your
Matrox MMS card. Make sure the
connectors are firmly in place.
Note:
Windows 2000/XP
– If you want to use TV output with your Matrox product, you
first need to connect at least one (1) computer monitor to be able to install the display
driver. After the display driver is installed with TV output support, you can connect your
dual-TV-output cables. For more information, see “TV output in the online version of
this guide.
* Only one dual-monitor cable is included with Matrox MMS×2 cards.
Dual-monitor
cable
WA RN I NG :
To avoid damaging the LFH-60 connector on your
dual-monitor cable or on your graphics card, carefully insert the
connector on your dual-monitor cable as straight as possible into the
connector on your graphics card. Specifically, inserting the
connectors into each other at an angle is likely to bend and damage
the pins on the connector of the dual-monitor cable.
Matrox G450 MMS – User Guide 7
2 Connect your monitors
Connect your preferred monitor to the main
DVI connector of your multi-monitor cable.
If your monitor has a DVI connector, connect it
directly to the main DVI connector of your
multi-monitor cable.
If your monitor has an HD-15 connector, use
the DVI-to-HD15 adapter included with your
product to connect your monitor to the main
connector. Make sure the connectors are
properly fastened.
Your Matrox card is now installed. Restart your computer and install your Matrox software
(see “Software installation, page 8).
Monitor
connector
(DVI)
DVI-to-HD15
adapter
Monitor connector
(HD15)
Note:
Monitors are numbered consecutively based
on which connector each is attached to.
Numbering starts with the primary display – the
one that first displays information when you
restart your computer. If another graphics card is
installed in your computer, display numbering
may be different.
Note:
To connect a
digital
monitor (a
monitor that uses digital input, usually a
flat panel monitor) to your Matrox
product, your monitor must have a DVI
connector.
Some monitors with DVI connectors
support both digital and analog input. If
youre using one of these monitors with
your Matrox product, make sure it’s configured to use the correct type of input. For more
information, see your monitor documentation.
DVI connector
(digital)
HD-15 connector (analog)
DVI connector
(analog/digital)
8 Matrox G450 MMS – User Guide
Software installation
This section describes how to install Matrox
software for
Windows 2000/XP or NT 4.0
.
You may need administrator rights to install
certain software. For more information, see
Windows documentation.
1 Install display driver
Windows detects new hardware when you restart. If Matrox display drivers haven’t been
previously installed, Windows prompts you to install a display driver. Follow the on-screen
instructions. (The Matrox Windows 2000/XP display driver is in the
Win2kXP
folder of your
Matrox installation CD-ROM.)
If you want to use TV output, you need to enable the feature when you install the display
driver. For more information on TV output, see “TV output”, page 14.
After the required display software is installed, youre prompted to restart your computer for
changes to take effect.
2 Install optional software
After your computer has restarted, insert (or reinsert) the Matrox installation CD-ROM in
your CD-ROM drive – the setup program automatically starts.
*
The setup program shows
you a list of additional items you can install. For each item you want to install, select a list
item, click
Install
, then follow the on-screen instructions.
3 Set up your display software
See “Display setup, page 9.
Note:
This guide has references that are specific to the Matrox installation CD-ROM. If your Matrox
product wasn’t packaged by Matrox (for example, if it was included with your computer), your
product may not include this CD-ROM.
If you don’t have this CD-ROM, certain references in this guide may not reflect the software you
have. For more information, see other software documentation provided by your system vendor.
* If Windows doesn’t automatically start the setup program, you can start it manually from the root folder of the CD-ROM.
Matrox G450 MMS – User Guide 9
Display setup
Windows 2000/XP or NT 4.0 –
Your Matrox display driver includes Matrox PowerDesk software. This
software helps you get the most out of your Matrox graphics card. This section has important
information on how to configure your display settings using Matrox PowerDesk software.
Accessing PowerDesk property sheets
Many display controls are on Matrox PowerDesk property sheets. You can identify
Matrox PowerDesk property sheets by the icon appearing on the tab. To access
these property sheets:
!
Windows 2000/XP
Right-click your Windows desktop background, then click
Properties
"
Settings
"
Advanced
. If youre using a multi-display desktop, select a
display before clicking
Advanced
.
!
Windows NT 4.0
– Click
Start
"
Settings
"
Control Panel
"
Matrox Display Properties
(double-click).
Also, to quickly access PowerDesk features, click the Matrox QuickDesk icon ( ) on your Windows
taskbar. To see the QuickDesk icon in Windows XP, you may need to click the
Show hidden icons
button ( ) on your Windows taskbar.
Monitor setup
Before changing your display resolution, color palette, or other Matrox PowerDesk settings, make
sure correct software monitor settings are selected. If you have a Plug-and-Play (DDC) monitor,
correct settings are usually automatically selected. The following explains how to make sure your
monitor settings are okay.
Note:
Multi-display mode is supported under Windows 2000/XP and NT 4.0. For more
information on multi-display mode, see Windows 2000/XP online help under “Multiple
Display support”.
WA R NI N G :
If incorrect software monitor settings are applied,
some
monitors can be
permanently damaged. For more information, see your monitor manual.
10 Matrox G450 MMS – User Guide
Windows 2000/XP
– If you have a Plug-and-Play (DDC) monitor, Windows should
automatically use correct settings for your monitor. To make sure the correct monitor is
selected in Windows:
1
Right-click your Windows desktop background, then click
Properties
"
Settings
"
Advanced
"
Monitor
. If youre using a multi-display desktop (see “Multi-display setup,
page 11), select a display before clicking
Advanced
.
2
If the monitor name listed doesn’t match your monitor, click
Properties
"
Driver
"
Update driver
. Follow the on-screen instructions.
3
If youre using a multi-display desktop (see “Multi-display setup, page 11), repeat steps
12 for each display in your Windows desktop.
For more information on Windows monitor settings, see Windows documentation.
If you want to customize your Windows monitor settings:
1
Access the PowerDesk
Monitor Settings
property sheet (see “Accessing PowerDesk
property sheets”, page 9).
2
Depending on what you want to do, click one of the buttons in the
Monitor settings
selection method
box, then follow the on-screen instructions.
Windows NT 4.0 –
1
Access the PowerDesk
Monitor
property sheet (see “Accessing PowerDesk property
sheets”, page 9).
2
If you have a Plug-and-Play monitor
:
Make sure the
Plug-and-Play (DDC) monitor
button is
selected. If so, the Matrox display driver
automatically
uses correct settings for your
monitor. If not, click this button, then click
Apply
.
If you don’t have a Plug-and-Play monitor
:
See if the
Default monitor (60 Hz)
button is selected. If
so, use the Matrox monitor selection method. For more information on Matrox monitor
selection, see Matrox PowerDesk online documentation.
3
If youre using a multi-display desktop (see “Multi-display setup, page 11), repeat steps
12 for each display in your Windows desktop.
Matrox G450 MMS – User Guide 11
Multi-display setup
To set up multi-display mode:
Windows 2000/XP
– If multi-display mode isn’t automatically enabled when you restart
Windows:
1
Right-click your Windows desktop background, then click
Properties
"
Settings
.
2
Select the disabled display, enable the
Extend my Windows desktop onto this monitor
check box, then click
Apply
.
3
To change resolution and color settings for each display, select a display, then change the
Screen area
and
Colors
settings. When you’re done, click
OK
.
Windows NT 4.0
1
Access the PowerDesk
Settings
property sheet (see “Accessing PowerDesk property
sheets”, page 9).
2
Click
Multi-Display Desktop
().
3
Move the
Desktop area
slider to adjust your multi-display desktop, then click
OK
to
accept your changes.
Advanced multi-display setup
Windows 2000/XP
– Use
Matrox Hybrid Display
to configure advanced display settings. With this
software, you can:
!
Combine 2 or more individual displays into a single Windows display. (A
Windows
display
is a display that Windows recognizes and that can be adjusted with Windows
controls.)
!
View a
clone
(copy) of a Windows display on one or more other displays.
!
Use up to 16 displays at a time by combining or copying displays. To do this, you need
more than one supported Matrox graphics card installed in your computer. (Without
this software, the maximum number of independent displays you can use at a time with
Windows 2000/XP is 10.)
!
Rotate one or more displays to support portrait orientation. (A
portrait
orientation is
taller than wide.)
!
Change the display layout to reflect the physical layout of your monitors.
Note:
In multi-display mode under Windows NT 4.0, the same display settings (resolution
and color palette) are used for each display.
12 Matrox G450 MMS – User Guide
To set up an advanced multi-display desktop:
1
Click the Matrox QuickDesk icon ( ) on your Windows taskbar, then click
Matrox
Hybrid Display
. To see the QuickDesk icon in Windows XP, you may need to click the
Show hidden icons
button ( ) on your Windows taskbar.
2
Select
Enable an advanced multi-display setup
, then click
Next
.
3
Select the maximum number of Windows displays you want to use. (Using only 1
Windows display for all your individual displays is also referred to as an
NT-style
multi-
display setup.)
4
Select the first
Undefined
display, then click
Display Setup
.
5
Make sure each of the following controls are using the setting you want. Adjust them in
this order:
a
Number of clones
b
Display layout
c
Display rotation
d
Display resolution
e
Color palette
f
Refresh rate
g
Enlarge mouse pointer
6
Click
OK
.
7
Repeat steps 4 to 6 until there are no more
Undefined
or available displays. An
Undefined
display won’t be used when Windows restarts.
8
Click
Next
.
9
Click
Finish
. For changes to take effect, your computer must be restarted.
For more information on specific controls, see context-sensitive help.
Note:
You can position each Windows display through the Windows controls. To access
these controls, right-click your Windows desktop background, then click
Properties
"
Settings
.
Matrox G450 MMS – User Guide 13
More PowerDesk information
For more information on Matrox PowerDesk:
Windows 2000/XP or NT 4.0
– For context-sensitive help where available, click the “
icon in the title bar, then click the item you want help on. Right-click a help topic for a
pop-up menu that lets you print or copy it. (Some help topics are only available through
context-sensitive help.)
Windows 2000/XP
– Access the PowerDesk
Information
property sheet (see “Accessing
PowerDesk property sheets”, page 9), then click
Help
or
View Readme File
.
Windows NT 4.0
!
Access the Matrox PowerDesk
Information
property sheet (see “Accessing PowerDesk
property sheets”, page 9).
!
Click the Matrox QuickDesk icon ( ) on your Windows taskbar, then click
Help
"
PowerDesk Guide
or
Help
"
View Readme File
.
14 Matrox G450 MMS – User Guide
TV output
With your Matrox card, you can use dual-TV-output cables
instead of dual-monitor cables. With dual-TV-output cables,
you can view or record your displays with TVs or video
recorders. While using TV output, all your displays use TV
output settings. If you want to use this feature and dual-TV-
output cables weren’t included with your Matrox product, you
can purchase them separately (see http://shopmatrox.com
).
This section describes how to use the
TV output
feature.
Connection setup
1 Turn off computer
Windows 2000/XP –
To shut down your computer, click
Start
"
Shut Down
"
Shut down
"
OK
, then turn off your computer.
Note:
To use TV output, you need to enable the feature when you install the display driver
for your Matrox product. If TV output isnt enabled, you need to reinstall the display driver
and enable TV output. For more information, see “Connection setup, page 6 and
“Software installation, page 8.
Note:
TV output isnt supported with full-screen DOS display modes (for example, the
information you see before Windows starts) or with standard VGA mode (for example,
when you restart Windows in “safe mode”). Older programs may use these display modes.
While one of these display modes is in use, your TV displays nothing (black).
Note:
Certain software (especially software that depends on hardware-based graphics
acceleration) may not work properly while TV output is used.
Dual-TV-output cable
WA R N I N G :
Dont change monitor connections while your computer is turned on. While
your computer is turned on, it may be using monitor settings that are specific to the
current monitor connections.
If a display device (monitor, TV or video recorder) is connected while your computer is
using settings intended for another display device, the display of the new device may be
garbled or unusable.
Some
devices may be permanently damaged if incorrect settings are
used.
Matrox G450 MMS – User Guide 15
2 Replace your dual monitor cables
a
Disconnect any computer monitor
connected to your dual-monitor cables.
b
Detach any dual-monitor cable from your
Matrox card.
c
Attach your dual-TV-output cables to your
Matrox graphics card.
*
3 Connect video output
To connect to a TV or a video recorder, youll
need a composite video (RCA) or S-video
cable.
If your video device (a TV or a video
recorder) didnt come with one of these
cables, these types of cable are available at
most electronics stores. The type of cable
you use depends on what your video device
supports. Many video devices support
composite video connections, and some
higher-quality video devices support
S-video connections.
For each TV or video recorder, you want to
connect to your Matrox product:
a
Attach one end of your composite video
or S-video cable to the appropriate
connector on your dual-TV-output
cable.
b
Attach the other end to the
VIDEO IN
connector on your TV
or video
recorder.
* Only one (1) dual-TV-output cable can be connected to Matrox MMS×2 cards.
Dual-TV-
output cable
Dual-monitor
cable
The labels on your devices may not be consistent with what’s in this guide. Different manufacturers sometimes use different labels
for the same type of controls and connectors. For example, the
VIDEO IN
connector on your TV may be labeled
VIDEO 1
(or
VIDEO
2
). To match labels, see the documentation for your video devices.
If your TV only has an antenna or cable TV connector, you can use an
RF modulator
to connect it to your Matrox card. RF
modulators are available at most electronics stores.
TV or video
recorder using
S-video
Composite
video (RCA)
cable
S-video cable
TV or video recorder
using composite video
Matrox card
Dual-TV-output
cable
(Note: Using the Matrox composite
video and S-video connectors at the
same time is optional.)
16 Matrox G450 MMS – User Guide
c
Before viewing or recording video output directly from your computer, make sure your
TV or video recorder is set up to use
line
input. For example, if your TV has a
TV/VIDEO
switch, set it to
VIDEO
; or if your video recorder has a
TUNER/LINE
switch, set it to
LINE
.
Optionally, if you use the composite video
and
S-video connectors on your Matrox TV
adapter, you can directly connect two different video devices at the same time.
To v i ew
and
record output from the same Matrox video connector, you can connect it to a
video recorder and connect the video recorder to a TV. For more information, see your video
recorder and TV manuals.
4 Connect audio output
Typically, the sound output from a
computer comes from speakers connected
to your sound card. If you prefer, you can
hear or record the sound output from your
computer using the same TV or video
recorder you connect to your graphics card.
To do this, you need an audio cable with a
stereo jack on one end and two RCA
connectors on the other end. If you dont
have this type of cable, you can buy one at
most consumer electronics stores.
a
Plug the stereo-jack end of the audio
cable into the
LINE OUT
*
()
connector on your sound card.
b
Plug the other end of the cable into the
left (
L
) and right (
R
)
AUDIO IN
connectors of your video device. For
more information, see your sound card
manual.
* If your computer has no audio
LINE OUT
connector, you can use its
SPKR
(speaker) connector instead. In this case, all your
computer sound output goes to the video device you connected to.
TV or video
recorder
Audio
connectors
Matrox G450 MMS – User Guide 17
Software setup
If a TV or video recorder is connected to your Matrox product, you can use TV output mode to view
or record your display on your TV or video recorder. (To connect video devices to your computer, see
page 14.)
TV settings have lower resolutions and refresh rates than typical computer monitor settings. Lower
refresh rates may result in more noticeable flicker.
Windows 2000/XP –
To adjust TV settings, access the Matrox PowerDesk
DualHead
property
sheet (see “Accessing PowerDesk property sheets, page 9).
Note:
Two TV standards are supported for TV output. The NTSC standard is used in North
America and Japan, among other places. The PAL standard is used in most of Western
Europe and in China, among other places.
If an incorrect TV standard is selected in Matrox software, the output from your computer
may not appear or record properly on your TV or your video recorder. To find out what
standard your TV or video recorder supports, see its documentation.
18 Matrox G450 MMS – User Guide
Troubleshooting
Basic procedures
This section explains basic procedures that are referred to by some troubleshooting items in this
guide.
Restarting in VGA mode
What follows is information on how to restart your computer in
VGA mode
.
Windows 2000/XP or NT 4.0 –
1
Restart your computer:
#
Windows 2000/XP
– Click
Start
"
Shut Down
"
Restart
"
OK
* to restart your
computer. (* Depending on your version and configuration of Windows, this part of
the step may not be necessary.)
#
Windows NT 4.0
– Click
Start
"
Shut Down
"
Restart the computer
"
Yes
.
If your primary monitor is unusable, see your system manual for information on how to
restart your computer using a hardware control.
2
Windows 2000/XP
Before
Windows starts, press [F8] for the Windows startup menu
to appear. (If [F8] doesn’t work, instead try pressing and holding [Ctrl] before Windows
starts.)
3
Select “VGA mode, then press [Enter].
Main troubleshooting
This section addresses possible problems that could prevent you from using your computer.
Problem Computer doesn’t display information or boot after Matrox card is
installed
1
Cause
Your Matrox card may not be properly installed.
1
Solution
Make sure your Matrox card is properly installed. Specifically, make sure the card is firmly
inserted in its expansion slot and that all connections to it are firmly in place. For more
information, see “Hardware installation, page 3.
Matrox G450 MMS – User Guide 19
2
Cause
There may be an unsupported graphics adapter in your computer. (For Matrox
multi-display
mode
in Windows NT, all graphics cards in your computer must be Matrox cards supported
by the display driver.)
1
Solution
If an unsupported graphics card is plugged into an expansion slot, remove it.
2
Solution
If a graphics adapter is built-in to your computer motherboard, your system may not have
automatically disabled it when you inserted your Matrox card. Check your system manual for
instructions on how to disable your computer’s built-in graphics adapter.
3
Cause
Your computer BIOS (Basic Input/Output System) may not be up to date. For more
information on your computer BIOS, see your system manual.
1
Solution
Reinstall your previous graphics card and, if possible, update your computer BIOS. This can
usually be done with software from the manufacturer of your computer. Contact your system
vendor or manufacturer to get a BIOS update for your computer.
To get the correct BIOS update, you may need to know the serial number your computer
displays when it restarts. (This number is usually in the lower-left corner of the display.)
Problem Wrong color balance, screen image off-center, or no picture at all
1
Cause
Your monitor video controls may be improperly set.
1
Solution
Adjust your monitor controls (brightness, contrast, and so on). For more information, see
your monitor manual.
2
Cause
Your monitor may not be properly connected.
1
Solution
Make sure your monitor is properly connected to the correct connector on your Matrox
graphics card (see “Connect your dual-monitor cables”, page 6).
2
Solution
Make sure the monitor power cable is firmly in place.
3
Cause
If display problems occur after the startup screen of your operating system, your software
monitor settings may be incorrect.
1
Solution
Make sure correct software monitor settings are selected.
If your primary display is still usable, see “Monitor setup, page 9. Otherwise, see the next
troubleshooting item.
20 Matrox G450 MMS – User Guide
Problem After the startup screen, or after display settings are changed, the
screen image is garbled or unusable
(blank screen, rolling or overlapping screen images)
1
Cause
Analog monitors only
– The Matrox display driver may be trying to use settings your
monitor doesn’t support. This can happen if a monitor was never selected in the software and
the display resolution was changed to one your monitor doesnt support, or if the monitor
connected to your computer was changed without changing it in the software.
1
Solution
Make sure the correct monitor is selected in Windows.
Windows 2000/XP –
1
If your primary display is unusable, restart your computer in VGA mode (see “Restarting
in VGA mode, page 18).
2
Right-click your Windows desktop background, then click
Properties
"
Settings
.
3
Move the
Screen area
(Windows 2000) or
Screen resolution
(Windows XP) slider down
to its lowest setting, then click
OK
.
4
Restart your computer normally.
5
Make sure the correct monitor is selected in Windows (see “Monitor setup, page 9).
6
Make sure you’re not using inappropriate monitor setting customizations: Access the
PowerDesk
Monitor Settings
property sheet (see “Accessing PowerDesk property sheets”,
page 9), then click
Delete all customizations
.
7
If necessary, restore your original display settings (see steps 2 and 3).
2
Windows NT 4.0 –
1
If your primary display is unusable, restart your computer in VGA mode (see “Restarting
in VGA mode, page 18).
2
Right-click your Windows desktop background, then click
Properties
"
Settings
.
Windows may prompt you that the display settings are incorrect for the current mode;
click
OK
to continue.
3
Move the
Desktop area
slider down to its lowest setting, then click
OK
.
WARN I NG:
If incorrect software monitor settings are applied,
some
monitors can be
permanently damaged. For more information, see your monitor manual.
Note:
In multi-display mode, each display has its own monitor settings (refresh rates).
Make sure correct software monitor settings are selected for
each
monitor.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55

Matrox G450 MMS Manuel utilisateur

Catégorie
Cartes graphiques
Taper
Manuel utilisateur

dans d''autres langues