Sony VPL-PX31 Manuel utilisateur

 2000 Sony Corporation

4-080-134-12(1)

VPL-PX21

VPL-PX31

Operating Instructions

Mode d’emploi

Manual de instrucciones

FR

ES

LCD Data Projector

GB

VPL-PX21/PX31

2 (GB)

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

WARNING

This label is located on

the rear of the Remote

Commander.

This label is located on the

rear of the Remote

Commander.

Caution

use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

Notes

• Do not aim the laser at people or not look into the laser

transmitter.

• When the Remote Commander causes malfunction,

consult with qualified Sony personnel. We change the

Remote Commander as new one according to the

guarantee.

This label is located on the

rear of the Remote

Commander.

Laser light shines out of this window.

For the customers in the USA

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your authority

to operate this equipment.

This label is located on

the side of the Remote

Commander.

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEAU

APPAREIL A LASER DE CLASSE 2

LASER–STRAHLING

NIGHT IN DEN STRAHL BLICKEN

LASER KLASSE 2

MAX OUTPUT:1mW

WAVE LENGTH:645nm

LASER RADIATION

DO NOT STARE INTO BEAM

WAVE LENGTH:645nm

MAX OUTPUT:1mW

CLASS II LASER PRODUCT

COMPLIES WITH DHHS 21 CFR

SUBCHAPTER J

SONY CORPORATION

6-7-35 KITASHINAGAWA

SHINAGAWA-KU,TOKYO,JAPAN

A

MANUFACTURED;

CAUTION

AVOID EXPOSURE

-

LASER

RADIATION IS EMITTED

FROM THIS APERTURE.

3 (GB)

For the customers in Canada

This Class A digital apparatus complies with Canadian

ICES-003.

For the customers in the United Kingdom

WARNING

THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with

the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol I or coloured green

or green-and-yellow.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red.

Voor de klanten in Nederland

Gooi de batterij niet weg maar lever

deze in als klein chemisch afval (KCA).

The socket-outlet should be installed near the equipment

and be easily accessible.

Warning on power connection

Use a proper power cord for your local power supply.

The United States, Continental UK, Ireland, Japan

Canada Europe Australia, New Zealand

Plug type VM0233 290B YP-12A COX-07 —

1)

YP332

Female end VM0089 386A YC-13B COX-02 VM0310B YC-13

Cord type SJT SJT H05VV-F H05VV-F N13237/CO-228 VCTF

Rated Voltage & Current 10A/125V 10A/125V 10A/250V 10A/250V 10A/250V 7A/125V

Safety approval UL/CSA UL/CSA VDE VDE VDE DENAN

.........................................................................................................................................................................................................

1) Use the correct plug for your country.

4 (GB)

5 (GB)

English

GB

Table of Contents

Overview

Precautions ............................................................... 7 (GB)

Features..................................................................... 8 (GB)

Location and Function of Controls......................... 9 (GB)

Front/Left Side ......................................................... 9 (GB)

Rear/Right Side/Bottom........................................... 9 (GB)

Control panel.......................................................... 11 (GB)

Connector panel ..................................................... 12 (GB)

Remote Commander .............................................. 13 (GB)

Setting up and projecting

Installing the Projector........................................... 14 (GB)

Connecting.............................................................. 15 (GB)

Connecting with a Computer ................................. 15 (GB)

Connecting with a VCR/15k RGB/Component

Equipment......................................................... 17 (GB)

Selecting the Menu Language............................... 18 (GB)

Projecting ................................................................ 19 (GB)

Effective tools for your presentation ..................... 21 (GB)

Adjustments and settings using the menu

Using the MENU...................................................... 22 (GB)

The PICTURE CTRL Menu ..................................... 22 (GB)

The INPUT SETTING Menu .................................... 24 (GB)

The SET SETTING Menu ........................................ 26 (GB)

The INSTALL SETTING Menu ................................ 27 (GB)

Installation

Installation Examples............................................. 28 (GB)

Floor Installation.................................................... 28 (GB)

Ceiling Installation................................................. 29 (GB)

Notes for Installation.............................................. 30 (GB)

Unsuitable Installation ........................................... 30 (GB)

Unsuitable Conditions for Use............................... 30 (GB)

6 (GB)

Maintenance

Maintenance............................................................ 32 (GB)

Replacing the Lamp ............................................... 32 (GB)

Cleaning the Air Filter ........................................... 33 (GB)

Troubleshooting ..................................................... 34 (GB)

Other

Specifications ......................................................... 36 (GB)

Index ........................................................................ 42 (GB)

7 (GB)

Precautions

On safety

•Check that the operating voltage of your unit is

identical with the voltage of your local power

supply.

•Should any liquid or solid object fall into the cabinet,

unplug the unit and have it checked by qualified

personnel before operating it further.

•Unplug the unit from the wall outlet if it is not to be

used for several days.

•To disconnect the cord, pull it out by the plug. Never

pull the cord itself.

•The wall outlet should be near the unit and easily

accessible.

•The unit is not disconnected to the AC power source

(mains) as long as it is connected to the wall outlet,

even if the unit itself has been turned off.

•Do not look into the lens while the lamp is on.

•Do not aim the laser at people or not look into the

laser transmitter.

•Do not place your hand or objects near the

ventilation holes — the air coming out is hot.

•Be careful not to catch your fingers by the adjuster

when you lift up the projector. Do not push hard on

the top of the projector with the adjuster out.

On illumination

•To obtain the best picture, the front of the screen

should not be exposed to direct lighting or sunlight.

•Ceiling-mounted spot lighting is recommended. Use

a cover over fluorescent lamps to avoid lowering the

contrast ratio.

•Cover any windows that face the screen with opaque

draperies.

•It is desirable to install the projector in a room where

floor and walls are not of light-reflecting material. If

the floor and walls are of reflecting material, it is

recommended that the carpet and wall paper be

changed to a dark color.

On preventing internal heat build-up

After you turn off the power with the I /

1

key on the

Remote Commander or on the control panel, do not

disconnect the unit from the wall outlet while the

cooling fan is still running.

Caution

The projector is equipped with ventilation holes

(intake) on the bottom and ventilation holes (exhaust)

on rear. Do not block or place anything near these

holes, or internal heat build-up may occur, causing

picture degradation or damage to the projector.

On cleaning

•To keep the cabinet looking new, periodically clean

it with a soft cloth. Stubborn stains may be removed

with a cloth lightly dampened with a mild detergent

solution. Never use strong solvents, such as thinner,

benzene, or abrasive cleansers, since these will

damage the cabinet.

•Avoid touching the lens. To remove dust on the lens,

use a soft dry cloth. Do not use a damp cloth,

detergent solution, or thinner.

•Clean the filter at regular intervals every 300 hours.

On repacking

•Save the original shipping carton and packing

material; they will come in handy if you ever have to

ship your unit. For maximum protection, repack your

unit as it was originally packed at the factory.

On LCD projector

The LCD projector is manufactured using high-

precision technology. You may, however, see tiny

black points and/or bright points (red, blue, or green)

that continuously appear on the LCD projector. This is

a normal result of the manufacturing process and does

not indicate a malfunction.

Precautions

Overview

8 (GB)

Features

High brightness, high picture quality

•High brightness

The high aperture ratio LCD panel with a microlens

and the 200 W UHP lamp allow high brightness

(light output 1800 ANSI lumen for VPL-PX21

(without a microlens), and 2800 ANSI lumen for

VPL-PX31) and excellent uniformity on the picture.

•High resolution

By adopting three 1.3-inch, approximately 790,000-

pixels XGA panels, this projector can project sharp

picture with the resolutions of 1024 × 768 pixels for

RGB input and 750 horizontal TV lines for video

input.

•High picture performance

This projector utilizes 3D Digital Gamma correction

for good picture uniformity. And the internal RGB

enhancer provides sharper RGB images.

Simple setup

•Sony original high performance APA (Auto Pixel

Alignment) function

You can get the clearest picture automatically by

simply pressing the APA key when the signal is

input from a computer.

•Simple setup with external equipment

This projector has 44 kinds of preset data for input

signals. You can get a suitable picture by connecting

an equipment with supplied cable and pressing the

APA key.

•USB, Digital RGB and 5BNC connectors

USB equipment (e.g., USB mouse) allows you to

expand your system. Using the application software

supplied with the projector allows you to control the

projector from your computer operated with

Windows

1)

98/98 Second Edition/2000 operating

system. The Digital RGB connector allows you to

connect the projector to a Digital RGB equipment.

The 5BNC input connector allows you to connect the

projector to a workstation output high-resolution

signals and to connect the projector to a computer

from a long distance.

Easy presentation

•Remote Commander with mouse control and

laser pointer functions

With the built-in mouse receiver, you can operate a

computer with the Remote Commander. For

presentations, you can use the laser pointer built into

the Remote Commander.

•Digital ZOOM, FUNCTION and HELP keys on

the Remote Commander

The Digital ZOOM allows you to enhance your

presentation by zooming in on the image.

You can allocate a presentation file to the

FUNCTION keys by using the application software

(CD-ROM) supplied with the projector. Just pressing

the FUNCTION key opens the file immediately.

The HELP key will be helpful if you encounter a

problem during operation.

•High portability

This projector is compact-7.2kg (15lb 14oz),

portable size. With such a feature, a carrying handle

contributes to a convenient carrying, and you can

carry it everywhere you want.

Multi scan compatibility

•Scan converter built-in

This projector has a built-in scan converter which

converts the input signal within 1024 × 768 pixels.

•Accept various input signals

This projector accepts video signals of the

composite, S video, and component as well as the

15k RGB, VGA

2)

, SVGA

2)

, XGA

2)

and SXGA

2)

signals, which all can be displayed.

•Compatible with six color systems

NTSC

3.58, PAL, SECAM, NTSC 4.43

3)

, PAL-M or

PAL-N color system can be selected automatically or

manually.

Other functions

Plug & Play

This projector complies with DDC1 and DDC2B.

(DDC1 and DDC2B are the Display Data Channel

(DDC

TM

)

4)

standard in the VESA standard.)

When connecting a DDC1 host system, the projector

synchronizes with V.CLK that follows the VESA

standard and outputs EDID (Extended Display

Identification Data) to the data line.

When connecting a DDC2B host system, the projector

automatically switches to the appropriate

communication mode.

Features

.........................................................................................................................................................................................................

1) Windows is a registered trademark of Microsoft Corporation (U.S.A. and other countries).

2) VGA, SVGA, XGA and SXGA are registered trademarks of the International Business Machines Corporation, U.S.A.

3) NTSC4.43 is the color system used when playing back a video recorded on NTSC on an NTSC4.43 system VCR.

4) DDC

TM

is a registered trademark of the Video Electronics Standard Association.

9 (GB)

Location and Function of

Controls

Front/Left Side

1 Zoom ring

Adjusts the size of the picture.

2 Focus ring

Adjusts the picture focus.

3 Lens

Open the lens cap before projection.

4 Ventilation holes (exhaust)

5 Front remote control detector (SIRCS receiver)

6 Adjuster

When a picture is projected on the out of the screen,

adjust the picture using this adjuster.

For details on how to use the adjusters, see “How to use

the adjuster” on page 10 (GB).

7 Security lock

Connects to an optional security cable (made by

Kensington)

1)

.

The security lock corresponds to Kensington’s

MicroSaver

®1)

Security System.

If you require further information, contact

Kensington

2855 Campus Drive, San Mateo, CA 94403

In North America

Phone: 800-235-6708

Fax: 800-247-1317

Outside North America

Phone: 847-541-9500

Home page address:

http://www.kensington.com/

8 Carrying handle

Pull up the handle from the projector for carrying.

9 Left speaker

0 Control panel

For details, see “Control panel” on page 11 (GB).

qa Right speaker

qs Lens hood

qd Rear remote control detector (SIRCS receiver)

Rear/Right Side/Bottom

Location and Function of Controls

2

3

6

45 7

8

9

1qa

qs 0

w;

qg

qj

qh

ql

qk

qd

qf

.........................................................................................................................................................................................................

1) Kensington and MicroSaver are registered trademarks of Kensington Technology Group.

10 (GB)

qf AC IN socket

Connects the supplied AC power cord.

qg Rear speaker

qh Lamp cover

qj Ventilation holes (intake)/air filter cover

Notes

•Do not place anything near the ventilation holes as it

may cause internal heat build-up.

•Do not place your hand or objects near the

ventilation holes — the air coming out is hot.

qk Air filter cover button

Used to remove the air filter cover.

For details, see “Cleaning the Air Filter” on page 33 (GB).

Note

Clean the air filter every 300 hours to ensure

optimal performance.

ql Adjuster buttons

w; Connector panel

For details, see page 12 (GB).

How to use the adjuster

To adjust the height

Adjust the height of the projector as follows:

1 Lift the projector and press the adjuster buttons.

The adjusters will extend from the projector.

2 While pressing the buttons, lower the projector.

Then, release the buttons.

The adjusters will lock, then the height of the

projector will be fixed. For fine adjustment, turn

the adjusters to the right and the left.

Notes

•Be careful not to let the projector down on your

fingers.

•Do not push hard on the top of the projector with the

adjusters out.

Location and Function of Controls

Adjuster buttons

11 (GB)

Location and Function of Controls

Control panel

1 VOL +/– keys

Adjust the volume of the built-in speakers and output

level of the AUDIO jack.

+ : Increases the volume.

– : Decreases the volume.

2 Arrow keys (M/m/</,)

Used to select the menu or to make various adjustments.

3 MENU key

Displays the on-screen menu. Press again to clear the

menu.

4 HELP key

If you need help information during an operation, press

this key to display help messages. The Help menu lists

error recoveries depending on problem type.

5 Indicators

LAMP/COVER: Lights up or flashes under the

following conditions:

• Lights up when the lamp has reached the end of

its life or becomes a high temperature.

• Flashes when the lamp cover or air filter cover

is not secured firmly.

TEMP (Temperature)/FAN: Lights up or flashes

under the following conditions:

• Lights up when temperature inside the projector

becomes unusually high.

• Flashes when the fan is broken.

POWER SAVING: Lights up when the projector is

in the power saving mode. When POWER

SAVING in the SET SETTING menu is set to

ON, the projector goes into the power saving

mode if no signal is input for 10 minutes.

Although the lamp goes out, the cooling fan

keeps running. In the power saving mode, any

key does not function for the first 40 seconds.

The power saving mode is canceled when a signal

is input or any key is pressed.

ON/STANDBY: Lights up or flashes under the

following conditions:

• Lights in red when the AC power cord is

plugged into the wall outlet. Once in the

standby mode, you can turn on the projector

with the

I / 1

key.

• Lights in green when the power is turned on.

• Flashes in green while the cooling fan runs after

turning off the power with the

I / 1

key. The

fan runs for about 120 seconds after turning off

the power.

The ON/STANDBY indicator flashes quickly

for the first 40 seconds.

During this time, you cannot turn the power

back on with the

I / 1

key.

For details on the LAMP/COVER and the TEMP/FAN

indicators, see page 35 (GB).

6

I

/

1

(

on / standby

)

key

Turns on and off the projector when the projector is in

the standby mode. The ON/STANDBY indicator

lights in green when the power is turned on.

When turning off the power, press the I /

1

key

twice following the message on the screen, or press

and hold the key for about one second.

For details on steps for turning off the power, see “To turn

off the power” on page 20 (GB).

7 INPUT key

Selects the input signal. Each time you press the key,

the input signal switches as follows:

The audio signals are common to the VIDEO and

S-VIDEO.

8 LIGHT key

If you press this key while the power is on, the keys

on the control panel will be displayed in orange.

Press this key to turn off the light.

9 APA (Auto Pixel Alignment) key

Adjusts a picture to be projected clearest

automatically while a signal from the computer is

input. Adjust the shift (up/down and left/right) at the

same time automatically.

Note

Press the APA key when the full image is displayed

on the screen. If there are black edges around the

image, the APA function will not function properly

and the image may extend beyond the screen.

q; RESET key

Resets the value of an item back to its factory preset

value. This key functions when the menu or a setting

item is displayed on the screen.

qa ENTER key

Enters the settings of items in the menu system.

INP

U

T

HELP

MENU

E

NT

E

R

RESET

A

P

A

L

IG

H

T

VOL +

VOL -

LAMP/

COVER

TEMP/

FAN

POWER

SAVING

ON/

STANDBY

1234

5

6

7

890qa

B INPUT-A B INPUT-B

S-VIDEO b VIDEO b

12 (GB)

Connector panel

1 INPUT A connectors

1DIGITAL RGB/5BNC/RGB switch: Selects

DIGITAL RGB, 5BNC or RGB on INPUT A

connectors. Select the appropriate position

depending on the input signal.

DIGITAL RGB: Signal input from DIGITAL

RGB connector.

5BNC: Signal input from the 5BNC connector.

RGB: Signal input from the RGB connector.

2RGB input connector (HD D-sub 15-pin,

female): Connects to the monitor output on a

computer using the supplied cable. This

connector only accepts signals from a computer.

35BNC input connectors (R/R-Y/P

R, G/Y, B/B-

Y/P

B, SYNC/HD, VD connectors) (BNC type):

Connect to a high-resolution computer or VCR

where signals are transmitted long distances; for

example, when the projector has been hung from

the ceiling.

According to the connected equipment, computer,

component (R-Y/Y/B-Y), HDTV or DTV (DTV

GBR, DTV YP

BPR) signal is selected.

Right side

Location and Function of Controls

4DIGITAL RGB input connector (DFP 20-pin,

TMDS): Connects to a digital RGB output

connector on external equipment.

5USB connector: Connects your computer or

USB equipment.

A plug: (Right, for downstream, 4-pin):

Connects to USB

equipment

.

B plug: (Left, for upstream, 4-pin):

Connects to

a computer. If you connect the projector and a

computer, the projector automatically assumes

that a USB mouse is connected; this allows you

to control the mouse from the Remote

Commander. The application software supplied

with the projector allows you to control the

projector from your computer.

6MOUSE (13-pin) connector: Connects to the

mouse port on a computer to control the mouse

function using the supplied mouse cable.

7AUDIO (stereo mini-jack) jack: Connects to the

audio output on a computer.

2 INPUT B connectors

Connect to external equipment such as a computer.

You can control the mouse signal with the Remote

Commander.

RGB input (HD D-sub 15-pin, female): Connects

to the monitor output on a computer using the

supplied cable. This connector only accepts

signals from a computer.

AUDIO (stereo mini-jack): Connects to the audio

output on a computer.

MOUSE (13-pin): Connects to the mouse port on a

computer to control the mouse function using the

supplied mouse cable.

3 VIDEO IN jacks

Connect to external video equipment such as a VCR.

S VIDEO (mini DIN 4-pin):

Connects to the S video

output (Y/C video output) on video equipment.

VIDEO (phono type): Connects to the composite

video output.

AUDIO input L (MONO)/R (phono type): Connect

to the audio output of equipment. For stereo

equipment, use both the L and R jacks; for monaural

equipment, use the L (MONO) jack only.

The audio signals are common to the VIDEO and

S VIDEO.

4 CONTROL S IN/PLUG IN POWER (DC 5V

output) jack

Connects to the control S out jacks of the Sony equipment.

Connects to the CONTROL S OUT jack on the supplied

Remote Commander when using it as a wired Remote

Commander. In this case, you do not need to install the

batteries in the Remote Commander, since the power is

supplied from this jack.

5 RS-232C connector (D-sub 9-pin, female)

Connects to a computer to operate the projector from

the computer.

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/P

R

B/B-Y/P

B

SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/P

R

B/B-Y/P

B

SYNC/HD VDG/Y

MOUUSEAUDIORGB

MOUUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

34

2

1

6

5

INPUT A

DIGITAL RGB

USB

R/R-Y/P

R

B/B-Y/P

B

SYNC/HD VDG/Y

MOUSEAUDIORGB

DIGITAL

RGB RGB

5BNC

76

2

1

5

3

4

13 (GB)

.........................................................................................................................................................................................................

1) Macintosh is a registered trademark of Apple Computer, Inc.

Remote Commander

The keys which have the same names as on the

control panel function identically.

You can control a connected computer using the

Remote Commander.

For details, see “Connecting with a Computer” on page

15 (GB).

Notes on laser beam

•Do not look into the laser transmitter.

•Do not aim the laser at people.

1

I

/

1

key

2 INPUT key

3 APA (Auto Pixel Alignment) key

4 VOLUME +/– keys

5 LASER key

Emits laser beam from the laser transmitter when you

press this key.

Location and Function of Controls

COMMAND

MUTING

VOLUME

HELP

/

INPUTAPA

FUNCTION

MENU

LASER

ENTER

RESET

D ZOOM

+

–

+

–

R CLICK

PIC

AUDIO

ONOFF

12

6

7

9

qd

qa,qs

qf

qg

qh

qj

qk

ql

w;

wa ws

0

8

5

4

2

1

3

6 OUTPUT connectors

MONITOR (HD D-sub 15-pin, female): Connects

to the video input connector on the monitor.

Outputs signals from the selected channel in the

INPUT A (RGB or 5BNC) or INPUT B (RGB)

connector. This connector does not output any

signals from the DIGITAL RGB connector.

AUDIO (phono type): Connects to external active

speakers.

The volume of the speakers can be controlled by the

VOLUME +/– keys on the Remote Commander or

the VOL +/– keys on the control panel.

6 Joy stick

Functions as a mouse of a computer connected to the

unit.

7 Arrow keys (M/m/</,)

8 L CLICK key

Functions as a left button on a mouse. When

connected to a Macintosh

1)

computer, the L CLICK

key functions as a mouse button.

9 R CLICK key

Functions as a right button on a mouse. When

connected to a Macintosh computer, the R CLICK key

functions as a mouse button.

0 D ZOOM +/– key

Enlarges the image at a desired location on the screen.

+: Pressing the + key once displays the icon. This

icon indicates the point you want to enlarge. Use

an arrow key (M/m/</,) to move the icon to

the point to be enlarged. Press the + key

repeatedly until the image is enlarged to your

requirements.

–: Pressing the – key reduces an image that has been

enlarged with the D ZOOM + key.

qa Strap holder

Attaches the supplied strap.

qs CONTROL S OUT jack (stereo minijack)

Connects to the CONTROL S IN jack on the projector

with the connecting cable (not supplied) when using

the Remote Commander as a wired one. In this case,

you do not need to install the batteries since the power

is supplied via the CONTROL S IN jack on the

projector.

qd RESET key

qf ENTER key

qg MENU key

qh FUNCTION 1/2 keys

When you connect the projector with a computer, you

can open a file on the screen by just pressing the

FUNCTION key. This will enhance your presentation.

To use this function, allocate a file to the FUNCTION

key by using the application software. For details on

how to allocate a file to the FUNCTION key, refer to

the help file of the application software.

14 (GB)

Location and Function of Controls / Installing the Projector

Be sure to

install the

battery from

the # side.

qj MUTING keys

Cut off the picture and sound.

PIC: Cuts off the picture. Press again to restore the

picture.

AUDIO: Cuts off the sound from speakers and

AUDIO jack. Press again or press the VOLUME

+ key to restore the sound.

qk HELP key

If you need help information during an operation,

press this key to display help messages.

ql COMMAND ON/OFF switch

When this switch is set to OFF, no key on the Remote

Commander function. This saves the battery power.

w; Transmission indicator

Lights up when you press a key on the Remote

Commander.

This indicator does not light up when you use the laser

pointer.

wa Infrared transmitter

ws Laser transmitter

Battery installation

1 Push and slide to open the lid, then install the two

size AA (R6) batteries (supplied) with the correct

polarity.

2 Replace the lid.

Notes on batteries

•Make sure that the battery orientation is correct when

inserting batteries.

•Do not mix an old battery with a new one, or

different types of batteries.

•If you will not use the Remote Commander for a

long time, remove the batteries to avoid damage

from battery leakage. If batteries have leaked,

remove them, wipe the battery compartment dry and

replace the batteries with new ones.

Notes on Remote Commander operation

•Make sure that there is nothing to obstruct the

infrared beam between the Remote Commander and

the remote control detector on the projector.

•The operation range is limited. The shorter the

distance between the Remote Commander and the

projector is, the wider the angle within which the

commander can control the projector.

Installing the Projector

This section describes the installation arrangements

for installing the projector.

Horizontal center

of the screen

The distance between the lens and the screen varies

depending on the size of the screen. Use the following table

as a guide.

Unit: m (feet)

Screen

size 40 60 80 100 120 150 200 300

(inches)

Minimum 1.5 2.3 3.1 3.9 4.6 5.8 7.8 11.7

Distance (4.9) (7.5) (10.0) (12.6) (15.2) (19.1) (25.5) (38.4)

Maximum 1.8 2.8 3.7 4.7 5.7 7.1 9.5 14.3

Distance (6.0) (9.1) (12.3) (15.4) (18.6) (23.3) (31.2) (46.9)

Distance between the screen

and the center of the lens

15 (GB)

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/PR B/B-Y/PB SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

DIGITAL

RGB RGB

5BNC

•insert the plugs of the cables properly; plugs that are

not fully inserted often generate noise. When pulling

out a cable, be sure to pull it out from the plug, not

the cable itself.

Notes

•Connect all the connecting cables to the INPUT A

connector when you input a signal from the INPUT

A connector.

Connect all the cables to the INPUT B connector

when you input a signal from the INPUT B

connector as well.

•Supplied mouse cables may not work properly

according to your computer.

When connecting with an IBM PC/AT

compatible computer

Right side

to serial

port or

to mouse

port

Monitor

SIC-S21 (for

serial)/S22

(for PS/2)

Mouse cable

(supplied)

to

monitor

out

Stereo audio

connecting

cable (not

supplied)

to

audio

out

HD D-sub

15-pin

cable

(supplied)

Connecting

Connecting with a Computer

This section describes how to connect the projector to

a computer.

You can control the projector from your computer by

using the application software supplied with the projector,

and/or you can use USB equipment. For details, see

“Using USB equipment (e.g., USB mouse)”.

When the projector is connected to a computer, you

can control the mouse of a computer by the Remote

Commander.

The R/L CLICK keys and joy stick function as follows.

Note

Make sure that there is nothing to obstruct the infrared

beam between the Remote Commander and the

remoter control detector on the projector.

Function

Key and

IBM PC/AT

1)

Macintosh

joy stick

compatible, Serial

R CLICK

(front)

Right button Mouse button

L CLICK

(rear)

Left button Mouse button

Joy stick Corresponds with the movements of the mouse

Also refer to the instruction manual of equipment to

be connected.

Notes

•This unit accepts the VGA, SVGA, XGA or SXGA

signals. However, we recommend you to set the

output signal of your computer to the XGA.

•If you set your computer, such as a notebook type

IBM PC/AT compatible, to output the signal to both

the display of your computer and the external

monitor, the picture of the external monitor may not

appear properly. In such cases, set the output mode

of your computer to output the signal to only the

external monitor.

For details, refer to the operating instructions supplied

with your computer.

•The RGB input connectors of the INPUT A/B and

DIGITAL RGB connector of the INPUT A comply

with the VESA DDC2B. If your computer or

graphics board is compatible with DDC, turn on the

power of the equipment as follows:

1 Connect the projector to the computer with the HD

D-sub 15-pin cable.

2 Turn on the power of the projector.

3 Boot up the computer.

When making connections, be sure to:

•

turn off all equipment before making any connections.

•use the proper cables for each connection.

Connecting

.........................................................................................................................................................................................................

1) IBM and PC/AT are a trademark and a registered trademark of International Business Machines Corporation, U.S.A.

Computer

Monitor

cable

SMF-410

(not

supplied)

Speaker

Note

Set the DIGITAL RGB/5BNC/RGB switch to RGB

(right) when you connect the computer to the

INPUT A connector.

Setting up and projecting

to INPUT A

or INPUT B

16 (GB)

When connecting with a Macintosh

computer

Right side

SIC-S20

Mouse

cable (not

supplied)

to mouse

port

to audio out

to

monitor

out

Connecting

Signal

adapter

(not

supplied)

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/PR B/B-Y/PB SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

DIGITAL

RGB RGB

5BNC

Stereo audio

connecting

cable (not

supplied)

Computer

Monitor

cable

SMF-410

(not

supplied)

HD D-sub

15-pin

cable

(supplied)

Speaker

Notes

•Set the DIGITAL RGB/5BNC/RGB switch to

RGB (right) when you connect the computer to

the INPUT A connector.

•When you connect with a Macintosh computer,

you need the optional signal adapter.

Right side

Using the DIGITAL RGB (TMDS)

connector

Connect the computer to the DIGITAL RGB (TMDS)

connector on the connector panel.

Note

If you use the DIGITAL RGB (TMDS) connector, the

MONITOR connector will not output image signals.

Notes

•Use the proper mouse cable for your computer.

•You can use a USB mouse. For details, see

“Using USB equipment (e.g., USB mouse)”.

•Set the DIGITAL RGB/5BNC/RGB switch to

DIGITAL RGB (left).

•To connect digital RGB equipment, use the digital

signal cable (SMF-D102 or SMF-D110) (not

supplied). Do not use other cables — noise may

appear on the image.

to INPUT A

or INPUT B

Mouse cable

Stereo audio

connecting

cable (not

supplied)

Digital signal

cable

SMF-D102

(not supplied)

or

SMF-D110

(not supplied)

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/PR B/B-Y/PB SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

DIGITAL

RGB RGB

5BNC

to mouse

port

to digital

RGB out

to audio

out

Computer

Remote

cable

to

RS-232C

port

17 (GB)

Connecting

Using USB equipment (e.g., USB mouse)

Connect the USB equipment to the USB connector on

the connector panel.

You can connect your computer to the projector via

the RGB connector, 5BNC connector or DIGITAL

RGB connector. (The example below uses the RGB

connector.)

On the USB function

When connecting the projector to a computer by

using the USB cable for the first time, the computer

recognizes the following devices automatically.

1 USB hub (general use)

2 USB human interface device (wireless mouse

function)

3 USB human interface device (projector control

function)

The computer also recognizes the device connected

to the downstream connector on the projector.

Recommended operating environment

When you use the USB function, connect your

computer as illustrated above. This application

software and the USB function can be used on a

computer loaded with Windows 98, Windows 98 SE

or Windows 2000 preinstall models.

Note

Set the DIGITAL RGB/5BNC/RGB switch to the

suitable position depending on the connection.

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/P

R

B/B-Y/P

B

SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

DIGITAL

RGB RGB

5BNC

Right side

HD D-sub

15-pin

cable

(supplied)

Stereo audio

connecting

cable (not

supplied)

to

monitor

out

to USB

port

to audio

out

Other USB

equipment

USB

cable A

type-B

type

(sup-

plied)

Computer

Notes

•As the projector recognizes the USB mouse when the

computer is connected to the USB connector, do not

connect anything to the MOUSE connector.

•Your computer may not start correctly when

connected to the projector via the USB cable. In this

case, disconnect the USB cable, restart the computer,

then connect the computer to the projector using the

USB cable.

•This projector is not guaranteed for suspend, standby

mode. When you use the projector in suspend,

standby mode, disconnect the projector from the

USB port on the computer.

•Operations are not guaranteed for all the

recommended computer environments.

Connecting with a VCR/15k RGB/

Component Equipment

This section describes how to connect the projector

with a VCR, external active speakers, and 15k RGB/

component equipment.

Also refer to the instruction manuals of the equipment

to be connected.

When making connections, be sure to:

•turn off all equipment before making any

connections.

•use the proper cables for each connection.

•insert the plugs of the cables properly; plugs that are

not fully inserted often generate noise. When pulling

out a cable, be sure to pull it out from the plug, not

the cable itself.

S-Video cable

(not supplied)

Audio/video

cable

(supplied)

Active speakers

to audio/video

outputs

to S video

output

VCR

Right side

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/P

R

B/B-Y/P

B

SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

18 (GB)

RS-232C

IN

PLUG IN POWER

OUTPUT

INPUT A

INPUT B

VIDEO IN

CONTROL S

REMOTE

DIGITAL RGB

USB

R/R-Y/PR B/B-Y/PB SYNC/HD VDG/Y

MOUSEAUDIORGB

MOUSEAUDIOAUDIO RGB

MONITOR

S VIDEO VIDEO AUDIO

L

R

(MONO)

DIGITAL

RGB RGB

5BNC

DIGITAL

RGB RGB

5BNC

Notes

•Set the aspect ratio using ASPECT in the INPUT

SETTING menu according to the input signal.

•To connect a 15k RGB/Component equipment,

select the COMPUTER/COMPONENT/DTV

YP

BPR/DTV GBR in the INPUT-A in the SET

SETTING menu according to the input signal.

•Use the composite sync signal when you input the

external sync signal from 15k RGB/component

equipment.

Connecting to a HDTV 1035/60i

Since the screen ratio of a high definition image is

16:9 and 576 lines are displayed in the vertical

direction, the image displayed is not a high-

definition image.

Right side

15k RGB/Component equipment

to RGB/

component

output

BNC Cable

(not supplied)

Stereo audio

connecting

cable

(not

supplied)

to

audio

output

Connecting / Selecting the Menu Language

Selecting the Menu Language

You can select the language for displaying in the

menu and other on screen displays. The factory setting

is ENGLISH.

1 Plug the AC power cord into the wall outlet.

2 Press the I /

1

key to turn on the power.

3 Press the MENU key.

The menu display appears.

4 Select the icon of SET SETTING Menu, the third

one, with the M or m key, then press the , or

ENTER key.

The SET SETTING Menu appears.

5 Select LANGUAGE with the M or m key, then

press the , or ENTER key.

6 Select the language desired with the M or m key,

then press the < or ENTER key.

The menu changes into the selected language .

To clear the menu display

Press the MENU key.

The menu display disappears automatically if no key

is pressed for one minute.

INPUT

HELP

MENU

E

N

T

E

R

RESET

APA

L

IG

H

T

VOL +

VOL -

LAMP/

COVER

TEMP/

FAN

POWER

SAVING

ON/

STANDBY

2

4, 5, 6 3

1

SET SETTING

STATUS: ON

INPUT-A: COMPUTER

AUTO INPUT SEL:

OFF

LANGUAGE: ENGLISH

SPEAKER: ON

POWER SAVING:

OFF

SIRCS RECEIVER:

FRONT&REAR

INPUT-A

19 (GB)

INPUT-B: Selects audio and video signals input

from the INPUT B connector.

VIDEO: Selects audio and video signals input

from the AUDIO/VIDEO (VIDEO IN)

jacks.

S-VIDEO:Selects audio and video signals input

from the AUDIO/S VIDEO (VIDEO

IN) jacks.

Note

The AUDIO (VIDEO IN) jacks are used as audio

outputs of both VIDEO and S-VIDEO.

4 Turn the zoom ring to adjust the size of the

picture.

5 Turn the focus ring to adjust the focus.

Note

Looking into the lens when projecting may cause

injury to your eyes.

To Press

Adjust the volume

the VOL +/– keys on the control panel or

the VOLUME +/– keys on the Remoter

Commander.

Cut off the sound the AUDIO MUTING key on the Remote

Commander. To restore the sound, press

the AUDIO MUTING key again or press

the VOL + key on the control panel or the

VOLUME + key on the Remote

Commander.

Cut off the picture

the PIC MUTING key on the Remote

Commander. To restore the picture, press the

PIC MUTING key again.

To get the clearest picture

You can get the suitable picture when a signal from

the computer is input. Press the APA key.

The picture is automatically adjusted to be projected

clearest.

Notes

•Adjust the signal when the still picture is displayed

on the screen.

•Press the APA key when the full image is displayed

on the screen. If there are black edges around the

image, the APA function will not function properly

and the image may extend beyond the screen.

•If you switch the input signal or re-connect a

computer, press the APA key again to get the

suitable picture.

Projecting

1 After all equipment is connected completely, plug

the AC power cord into the wall outlet.

The ON/STANDBY indicator lights in red and the

projector goes into the standby mode.

2 Press the I /

1

key.

The ON/STANDBY indicator lights in green.

3 Turn on equipment connected to the projector.

Press the INPUT key to select the input source.

INPUT-A:Selects audio and video signals input

from the INPUT A connector.

Projecting

Rear

remote

control

detector

ON/STANDBY

indicator

INPUT

HELP

MENU

E

N

T

E

R

RESET

APA

L

IG

H

T

VOL +

VOL -

LAMP/

COVER

TEMP/

FAN

POWER

SAVING

ON/

STANDBY

COMMAND

MUTING

VOLUME

HELP

/

INPUTAPA

FUNCTION

MENU

LASER

ENTER

RESET

D ZOOM

+

–

+

–

R CLICK

PIC

AUDIO

ONOFF

12

2

3

1

4

5

2

3

(Front)

APA key

20 (GB)

Projecting

•“ADJUSTING” appears on the screen. Press the

APA key again during the adjustment to restore the

original screen.

•“Complete!” appears on the screen when the picture

is adjusted properly. The picture may not be adjusted

properly depending on the kinds of input signals.

•Adjust the items in the INPUT SETTING menu

when you adjust the picture manually.

For details, see page 24 (GB).

To correct the trapezoid

When the projecting image is a trapezoid, change the

projector’s position/height by moving the adjuster.

For details on “How to use the adjuster”, see page 10

(GB).

If the image is still a trapezoid, correct it in DIGIT

KEYSTONE in the INSTALL SETTING menu.

When the base edge is longer than the upper

edge as shown in the figure below:

When the upper edge is longer than the base

edge as shown in the figure below:

For details on “DIGIT KEYSTONE”, see page 27 (GB).

To turn off the power

1 Press the I /

1

key.

“Power OFF?” appears on the screen.

Note

The message will disappear if you press any key

except the I /

1

key, or if you do not press any

key for five seconds.

2 Press the I /

1

key.

The ON/STANDBY indicator flashes in green and

the fan continues to run for about 120 seconds to

reduce the internal heat. Also, the ON/STANDBY

indicator flashes quickly for the first 40 seconds.

During this time, you will not be able to turn the

power back on with the I /

1

key.

3 Unplug the AC power cord from the wall outlet

after the fan stops running and the ON/STANDBY

indicator lights in red.

When you cannot confirm the on-screen

message

When you cannot confirm the on-screen message in a

certain condition, you can turn off the power by

holding the I /

1

key for about one second.

Note

Do not unplug the AC power cord while the

fan is still running; otherwise, the fan will

stop although the internal heat is still high,

leading to breakdown of the projector.

About the air filter cleaning

Clean the air filter every 300 hours to ensure

optimal performance.

Set the value to negative.

Set the value to positive.

La page charge ...

Sony VPL-PX31 Manuel utilisateur

Sony VPL-PX31 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents