Sony CDP-XA30ES Manuel utilisateur

3-858-365-12 (1)

 1997 by Sony Corporation

Operating Instructions

Mode d’emploi

Manual de instrucciones

Bruksanvisning

EN

F

ES

S

CDP-XA50ES

CDP-XA30ES

2

EN

WARNING

To prevent fire or shock

hazard, do not expose

the unit to rain or

moisture.

To avoid electrical shock,

do not open the cabinet.

Refer servicing to

qualified personnel only.

Do not install the

appliance in a confined

space, such as a bookcase

or built-in cabinet.

Welcome!

Thank you for purchasing the Sony

Compact Disc Player. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

About This Manual

The instructions in this manual are for

models CDP-XA50ES and CDP-XA30ES.

The CDP-XA50ES is the model used for

illustration purposes, unless otherwise

mentioned. Any difference in operation

is clearly indicated in the text, for

example, “CDP-XA50ES only.”

Conventions

• Instructions in this manual describe

the controls on the player.

You can also use the controls on the

remote if they have the same or similar

names as those on the player.

• The following icons are used in this

manual:

Indicates that you can do the

task using the remote.

Indicates hints and tips for

making the task easier.

This appliance is classified as a CLASS 1

LASER product.

The CLASS 1 LASER PRODUCT

MARKING is located on the rear

exterior.

The following caution label is located

inside the unit.

Getting Started

EN

3

EN

Getting Started

Unpacking............................................................................................................................. 4

Hooking Up the System...................................................................................................... 4

Playing a CD............................................................................................................................. 6

Playing CDs

Customising the Sound of Your Music (Digital Filter Function).................................. 8

Using the Display .............................................................................................................. 10

Locating a Specific Track .................................................................................................. 11

Locating a Particular Point in a Track ............................................................................ 12

Playing Tracks Repeatedly ............................................................................................... 12

Playing in Random Order (Shuffle Play) .......................................................................13

Creating Your Own Programme (Programme Play) .................................................... 14

Playing Only Specific Tracks (Delete Play) Z .............................................................. 16

Recording From CDs

Recording Your Own Programme ..................................................................................17

Recording a CD by Specifying Tape Length (Time Edit/Just Edit) ........................... 18

Fading In or Out................................................................................................................. 19

Useful Tips for Recording Z ........................................................................................... 21

Storing Information About CDs (Custom Files)

What You Can Do With the Custom Files ..................................................................... 22

Indexing a Disc (Custom Index) ......................................................................................22

Storing Specific Tracks of a Disc (Delete Bank)............................................................. 24

Additional Information

Precautions ......................................................................................................................... 26

Notes on CDs...................................................................................................................... 26

Troubleshooting ................................................................................................................. 27

Specifications ...................................................................................................................... 27

Index

Index .................................................................................................................................... 28

TABLE OF CONTENTS

Getting Started

4

EN

LINE OUT

FIXED

CD

Unpacking

Check that you received the following items:

• Audio connecting cord (1)

• Remote commander (remote) (1)

• Sony SUM-3 (NS) batteries (2)

• Stabiliser (1)

Inserting batteries into the remote

You can control the player using the supplied remote.

Insert two R6 (size AA) batteries by matching the +

and – on the batteries. When using the remote, point it

at the remote sensor g on the player.

Hooking Up the System

Overview

This section describes how to hook up the CD player to

an amplifier. Be sure to turn off the power of each

component before making the connections.

When to replace batteries

With normal use, the batteries should last for about six

months. When the remote no longer operates the player,

replace all the batteries with new ones.

Notes

• Do not leave the remote near an extremely hot or humid

place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from battery

leakage and corrosion.

To mains

CDP-XA50ES

DIGITAL OUT

COAXIAL

LINE OUT

VARIABLE

DIGITAL OUT

OPTICAL

To mains

Amplifier

To mains

CDP-XA30ES

DIGITAL OUT

COAXIAL

LINE OUT

VARIABLE

DIGITAL OUT

OPTICAL

To mains

Amplifier

: Signal flow

CD

LINE OUT

FIXED

: Signal flow

Getting Started

5

EN

Hookups

pWhen making analog hookups

When connecting an audio cord, be sure to match the

colour-coded cord to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

Amplifier

AmplifierCD player

• If you have an analog power amplifier

Connect the amplifier via the VARIABLE LINE OUT jacks

using the supplied audio cord. You can adjust the output

level with the LINE OUT/PHONE LEVEL control on the

player or the LINE OUT LEVEL buttons on the remote.

• If you have a digital component with an optical digital

input connector

Connect the component via the DIGITAL OUT (OPTICAL)

connector using the optical cable (not supplied). Take off

the cap and plug in the optical cable.

CD player

Digital component

CD player

What cords will I need?

pWhen making analog hookups

• Audio cord (supplied) (1)

White

(L)

Red

(R)

White

(L)

Red

(R)

pWhen making digital hookups

• Optical cable POC-15 (not supplied)

• Coaxial cable (not supplied)

LINE OUT

FIXED

L

R

L

R

VARIABLE

INPUT

CD

L

R

LINE OUT

FIXED

L

R

L

R

VARIABLE

INPUT

CD

L

R

DIGITAL OUT

OPTICAL COAXIAL

DIGITAL IN

OPTICAL

• If you have a digital component with a coaxial digital

input connector

Connect the component via the DIGITAL OUT (COAXIAL)

connector using the coaxial cable (not supplied).

Digital component

CD player

Note

When you connect via the DIGITAL OUT connector, noise

may occur when you play CD software other than music, such

as a CD-ROM.

pWhen making digital hookups

You can avoid deterioration of the signal during

transmission, since the music signal output through

the digital output connectors retains digital form.

You can connect a digital component such as a

digital amplifier, D/A converter, DAT or MD. When

you connect a DAT or MD, you can make digital

recordings from CDs.

Note that you cannot use fading in or out function

(page 19) when making this connection.

DIGITAL IN

COAXIAL

DIGITAL OUT

OPTICAL COAXIAL

Setting the voltage selector (voltage

selector equipped models only)

Check that the voltage selector on the rear panel of the

player is set to the local power line voltage. If not, set

the selector to the correct position using a screwdriver

before connecting the mains lead to a wall outlet.

Connecting the mains lead

Connect the mains lead to a wall outlet.

Removing the notice sheet

The notice sheet is put on the player. Remove the sheet

before you use your player.

220 - 240 V110 - 120 V

Basic Operations

6

EN

Playing a CD

23

1

2

• See pages 4 – 5 for the hookup

information.

If you turn on the player with

a CD in the tray

You can start playing

automatically from the

beginning of the CD. If you

connect a commercially

available timer, you can start

playing the CD at any time

you want.

Turn on the amplifier and select the CD player position.

Press POWER to turn on the player.

4

CHECK CLEAR FILTER

PUSH ENTER

AMS

REPEAT TIME

TIME FADE FILE ERASE

EDIT/

PHONE LEVEL

LINE OUTPHONES

POWER

010

OPEN/CLOSE

MODE

PLAY

Connect the

headphones.

Adjust the

headphones volume.*

CHECK CLEAR FILTER

OPEN/CLOSE

REPEAT

FILE ERASE

TIME FADE

EDIT/

PUSH ENTER

AMS

TIME

PHONE LEVEL

LINE OUT

010

PHONES

POWER

PLAY MODE

234

Connect the

headphones.

Adjust the

headphones volume.*

CDP-XA50ES

CDP-XA30ES

*The output level from the LINE OUT

VARIABLE jacks will also change.

Basic Operations

7

EN

To stop playback

Press π.

When you want to

Pause

Resume play after pause

Go to the next track

Go back to the preceding track

Stop play and remove the CD

Press ·.

The disc tray closes and the player plays all the tracks once

(Continuous Play).

Adjust the volume on the amplifier.

4

You need to

Press ∏

Press ∏ or ·

Turn ≠ AMS ± clockwise. (When

using the remote, press +.)

Turn ≠ AMS ± anticlockwise.

(When using the remote, press =.)

Press § OPEN/CLOSE

Press § OPEN/CLOSE, and place a CD on the tray.

3

With the label side up

Place the supplied stabiliser on the

CD. (The stabilisers supplied with the

CDP-XA50ES and CDP-XA30ES are

different.)

If “–––––” appears in the

display

Place the supplied stabiliser

on the CD.

If you do not, this indication

appears.

Note

In Step 3, do not place two or

more CDs at the same time.

If you do so, you may damage

the discs and/or the player.

If play doesn’t start from the

first track

Press PLAY MODE

repeatedly until

“SHUFFLE,” “PROGRAM”

and “CUSTOM INDEX”

disappear from the display

(or press CONTINUE on the

remote).

Playing CDs

8

EN

-120

0

22.05k

Customising the Sound of Your

Music (Digital Filter Function)

This player has a variable coefficient (V.C.) digital

filter. By selecting the type of filter you want, you can

adjust the sound to match your system, your room, the

music source, etc.

Selecting the filter directly on the player

1 Press FILTER.

The display shows the currently selected filter

number and the filter indicator flashes.

2 Turn ≠ AMS ± until the digital filter number

you want appears in the display.

As you turn the ≠ AMS ± control, the digital

filter number changes cyclically as follows:

If you are playing a disc, the sound will be

interrupted momentarily.

≠ AMS ±FILTER

CDP-XA50ES

≠ AMS ±FILTER

CDP-XA30ES

3 Push ≠ AMS ± to select the filter.

The original display reappears.

The selected digital filter number is stored in

memory even if you turn off the power.

You can also change the digital filter number by

pressing the FILTER button while the indicator is

flashing

Selecting the filter using the remote Z

1 Press DIGITAL FILTER.

The display shows the currently selected filter

number and the filter indicator flashes.

2 Press DIGITAL FILTER repeatedly until the

display shows the digital filter number you want.

The digital filter number is stored and the original

display reappears.

What is a variable coefficient (V.C.) digital

filter?

CD players use digital filters to eliminate the noise

generated during sampling. You can change the tone of

your music by changing the cutoff characteristics of the

digital filter.

This player has five types of filters with different

coefficient characteristics: “STD,” “1,” “2,” “3” and “4.”

In addition, digital filters “3” and “4” each have three

coefficient patterns, A–C, for more detailed

adjustments.

The following explains the terms you need to know to

understand the characteristics of the digital filters used

in this player.

Sharp roll-off and slow roll-off

Digital filters can be roughly classified into sharp roll-

off types and slow roll-off types, according to their

cutoff characteristics.

Response

(dB)

(Slow roll-off filter)

(Sharp roll-off filter)

Frequency (Hz)

Comparison of cutoff characteristics for sharp roll-off filter

and slow roll-off filter

DIGITAL FILTER

n STD n 1 n 2 n 3A n 3b n 3C n 4A n 4b n 4C

Playing CDs

9

EN

Cascade type and direct type

There are two methods of digital filter oversampling:

the cascade type and direct type. The cascade type

multiplies the signal by eight in three stages, and the

direct type multiplies the signal by eight in one step.

Cascade filters have a high calculation efficiency, and

can realise steep, high-precision sharp roll-off

characteristics. Moreover, the ICs in this player use the

full feed-forward (FF) method between each of the

stages to improve the accuracy of the information

transfer.

On the other hand, eightfold oversampling data can be

obtained in one step with direct filters and there is no

loss during transfer between calculation stages.

However, since such circuits are extremely large, this

player can only support slow roll-off filters.

2 2 2

8

Characteristics of each digital filter

The following are the settings and characteristics for

each of the five digital filters. Use this information to

select the filter you want.

STD: Standard

This is a sharp roll-off, cascade type filter. It has the

same characteristics as the digital filters that have long

been used in Sony’s high-end units and has a sharp

cutoff that reaches –120 dB at 24 kHz. This filter uses

the full feed-forward method between the calculation

stages and gives the sound a wide range and ample

spatial representation.

1: Spline

This is a slow roll-off, cascade type filter that uses a

cubic spline function for interpolation. The spline

function features smoother connections between

points, and among spline functions, the cubic filter is

the most straightforward. Ringing in the impulse

response for this filter is much lower than for a sharp

roll-off type filter. With this filter, the sound image is

clear and sound reproduction is smooth.

2: Plain

This is a slow roll-off, direct type filter. It features an

absence of quantization between the digital filter

output and the D/A converter input.

Direct type calculations are used within the digital

filter and the bit length for the digital filter output and

the D/A converter input are the same, so no

requantization noise is generated between the digital

filter and the D/A converter. This means that, of the

16-bit information taken from the disc, elements up to

20 kHz are input as far as the D/A converter without

any nonlinear operation. This reproduces a sound with

high clarity and strength.

Sharp roll-off filter

Slow roll-off filter

Pre-ringing Post-ringing Pre-ringing

Post-ringing

Comparison of impulse response for sharp roll-off filter

and slow roll-off filter

IN OUT

FF FF

Sharp roll-off filters steeply cut off the noise generated

during sampling over 22.05 kHz. This is a superior way

of completely reproducing signals below 20 kHz: the

basic principle behind digital audio.

On the other hand, slow roll-off filters cut off the noise

generated during sampling gradually, and are able to

hold pre-ringing and post-ringing (a kind of sound

smearing) in the impulse response signal to a

minimum.

Playing CDs

10

EN

Using the Display

You can check information about the disc using the

display.

CDP-XA50ES

TIME

DISPLAY MODE

Checking the total number and playing

time of the tracks

Press TIME before you start playing.

The display shows the total number of tracks, total

playing time and music calendar.

Total playing timeTotal number of

tracks

Music calendar

TIME

CDP-XA30ES

TIME

12345

678910

MIN SEC

3: Analog type

This is a slow roll-off, direct type filter that simulates a

seventh-order analog Butterworth filter. This filter

completely prevents pre-ringing in the impulse

response. Also, since it simulates an analog filter, the

high-region phase outside the audible frequency is

rotated. The filters from 3A to 3C differ in degree of

phase rotation. 3A is multiplied by one (the true analog

characteristic), 3b is multiplied by 0.75, and 3C is

multiplied by 0.5. The impulse response changes as

shown in the figures below. The degree of pre-ringing

and post-ringing varies with the degree of phase

change. This gives the sound a feeling of warmth and

depth.

4: Butterworth

This is a slow roll-off, direct type filter and includes

fifth-order through ninth-order Butterworth filters.

However, the phase is linear and does not include the

phase change possibilities of filter 3 (analog type). As

the figure below shows, only the cutoff characteristics

can be changed in the fifth-order (4A), the seventh-

order (4b) and the ninth-order (4C). Ringing in the

impulse response increases from the fifth-order filter to

the ninth-order filter. This filter gives the sound a

feeling of balance and comfort.

Note

The Digital Filter function primarily changes characteristics

outside the audible frequency. They cannot affect changes

within the audible frequency such as those provided by the

tone controls of the amplifier. Therefore, with certain

combinations of hardware and software, there may be no

noticeable effect after switching the filter.

20k

Comparison of filter 4 cutoff characteristics

Frequency (Hz)

Comparison of filter 3 impulse response

3A 3b 3C

Response

(dB)

4A

4b

4C

Playing CDs

11

EN

While in Shuffle Play mode (“SHUFFLE” appears in

the display; see page 13), a one-second access time

blank is added between each track. This increase is

automatically added to the total playing time in the

display.

If the disc has more than 15 tracks, the z indication

appears next to 15 on the music calendar.

The information also appears when you press

§ OPEN/CLOSE to close the disc tray.

Display information while playing a disc

While playing a disc, the display shows the current

track number, index number, playing time and the

music calendar.

Current track

number

Playing time

Music calendar

Index number (page 12) or Custom Index

number (page 22)

The track numbers in the music calendar disappear

after they are played.

Checking the remaining time

Each time you press TIME while playing a disc, the

display changes as shown in the chart below.

If the remaining time exceeds 100 minutes

in programme mode, “––.––” appears

instead of the remaining time.

Press

Playing time

and number

of the current

track

Remaining

time on the

current

track

Remaining

time on the

disc

Press

12345

678910

MIN SECINDEX

Locating a Specific Track

You can quickly locate any track while playing a disc

using the AMS (Automatic Music Sensor) on the player

or number buttons on the remote.

Number

buttons

>10

=/+

To locate

The next or

succeeding tracks

The current or

preceding tracks

A specific track

directly Z

When you directly locate a track numbered over 10

Z

Press >10 first, then the corresponding number buttons

on the remote. To enter “0,” use button 10.

Example: To play track number 30

Press >10 first, then 3 and 10.

You need to

Turn ≠ AMS ± clockwise until

you find the track. When using the

remote, press + repeatedly until you

find the track.

Turn ≠ AMS ± anticlockwise

until you find the track. When using

the remote, press = repeatedly until

you find the track.

Press the number button of the track

on the remote

≠ AMS ±

Turning off the music calendar in the

display

Each time you press DISPLAY MODE on the remote

while playing a disc, the music calendar turns off and

on alternately in the display.

12345

678910

MIN SECINDEX

12345

678910

MIN SECINDEX

12345

678910

MIN SEC

Playing CDs

12

EN

Playing Tracks Repeatedly

You can play tracks repeatedly in any play mode.

REPEAT

A˜B

REPEAT

Press REPEAT while playing a disc.

“REPEAT” appears in the display. The player repeats

the tracks as follows:

When the disc is played in

Continuous Play (page 6)

Shuffle Play (page 13)

Programme Play (page 14)

Delete Play (page 16)

Delete Shuffle Play

(page 14, 16)

Custom Index Play

(page 23)

To cancel Repeat Play

Press REPEAT repeatedly until “REPEAT” disappears from

the display.

The player repeats

All the tracks

All the tracks in random

orders

The same programme

All the remaining tracks

All the remaining tracks in

random orders

The portion between two

indexes

CDP-XA50ES

CDP-XA30ES

REPEAT

Locating a Particular Point in a

Track

You can also locate a particular point in a track while

playing a disc.

0/)

INDEX Ç/ç

0/)

To locate a point

While monitoring the

sound

Quickly by observing

the display during

pause

Using an index (only

for indexed discs)

What is an index?

It is a number that divides a track or a disc into sections,

enabling you to easily locate a desired point. You can

determine if a disc uses indexes by its packaging.

Note

If “ ” appears in the display, the disc has reached the end

while you were pressing ). Press 0 or turn

≠ AMS ± anticlockwise to go back.

Press

) (forward) or 0 (backward)

and hold down until you find the

point

0/) and hold down until you

find the point. You will not hear the

sound during the operation.

INDEX Ç/ç on the remote

repeatedly until you find the point

Playing CDs

13

EN

Repeating the current track

You can repeat only the current track.

While the track you want is being played, press

REPEAT repeatedly until “REPEAT 1” appears in the

display.

Note

You cannot repeat the current track while the disc is played in

Custom Index Play mode (see page 23).

Repeating a Specific Portion (A˜B Repeat)

You can play a specific portion in a track repeatedly.

This might be useful when you want to memorise

lyrics.

Note that you cannot repeat a portion extending to two

tracks.

1 While playing a disc, press A˜B on the remote

when you find the starting point (point A) to be

played repeatedly.

“A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point (point B), press

A˜B again.

“REPEAT A-B” appears. The player plays this

specific portion repeatedly.

To cancel A˜B Repeat

Press REPEAT.

Setting a new starting point

You can move the repeating portion ahead by

changing the starting point.

1 Press A˜B while the player is repeating the

specific portion.

The ending point B becomes the new starting point

A. “A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point (point B), press

A˜B again.

“REPEAT A-B” appears. The player repeats

between the new starting and ending points.

When you want to restart from the starting point A

Press · during A˜B Repeat.

Playing in Random Order

(Shuffle Play)

You can have the player “shuffle” tracks and play in a

random order.

·

PLAY MODE

·

PLAY MODE

1 Press PLAY MODE repeatedly until “SHUFFLE”

appears in the display.

When using the remote, press SHUFFLE.

2 Press · to start Shuffle Play.

The

indication appears while the player is

“shuffling” the tracks.

To cancel Shuffle Play

Press PLAY MODE four times (or CONTINUE on the remote).

CDP-XA30ES

CDP-XA50ES

SHUFFLE

CONTINUE

·

Playing CDs

14

EN

PLAY MODE

Creating Your Own

Programme (Programme Play)

You can arrange the order of the tracks on a disc and

create your own programme. The programme can

contain up to 24 tracks.

PLAY MODE

CDP-XA50ES

CDP-XA30ES

CONTINUE

Number

buttons

>10

·

=/+

2 Turn ≠ AMS ± until the track number you

want appears in the display.

The playing order and the track numbers being

programmed flash and the total playing time

including the track appears in the display.

≠ AMS ±

CHECK

π

·

CLEAR

CHECK

π

·

CLEAR

≠ AMS ±

PROGRAM

CLEAR

CHECK

p

Track numbers being

programmed

25

8

PROGRAM

MIN SEC

STEP

Total playing time

Playing order

Programmed tracks

3 Push ≠ AMS ± to select the track.

Last programmed

track

Playing order

Programmed

tracks

Total playing time

25

8

PROGRAM

MIN SEC

STEP

Creating a programme on the player

1 Press PLAY MODE repeatedly until “PROGRAM”

appears in the display before you start playing.

12345

678910

PROGRAM

You can start Shuffle Play while playing

Press PLAY MODE once (or SHUFFLE on the remote),

and Shuffle Play starts from the current track.

You can delete unwanted tracks during Shuffle Play

(Delete Shuffle Play)

Press the number button of the track you want to delete

on the remote.

The track number and “OFF” appear in the display, and

then the track number disappears from the music

calendar.

If you want to restore the track, press the number button

again.

To restore all the tracks, press π in stop mode.

If you’ve made a mistake

Press CLEAR, then repeat Steps 2 and 3.

Playing CDs

15

EN

4 Repeat Steps 2 and 3 to programme the tracks in

the order you want.

5 Press · to start Programme Play.

To cancel Programme Play

Press PLAY MODE three times.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

The programme remains even after the Programme

Play ends

When you press ·, you can play the same programme

again.

Notes

• “––.––” appears instead of the total playing time in the

display when it exceeds 100 minutes.

• “FULL” appears in the display when you try to add a track

to a programme which already contains 24 tracks.

Creating a programme using the remote

1 Press PROGRAM before you start playing.

“PROGRAM” appears in the display.

2 Press number buttons of the tracks you want to

programme in the order you want.

Example: To programme the tracks 2, 8 and 5

Press number buttons in the order 2, 8

and 5.

Last programmed

track

Playing order

3 Press · to start Programme Play.

To cancel Programme Play

Press CONTINUE.

You can check the total playing time while

programming using the remote (Programme Edit)

To select a track, press = or + and check the total

playing time. Then press PROGRAM to confirm your

selection.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

The programme remains even after the Programme

Play ends

When you press ·, you can play the same programme

again.

Notes

• “––.––” appears instead of the total playing time in the

display when it exceeds 100 minutes.

• “FULL” appears in the display when you try to add a track

to a programme which already contains 24 tracks.

Checking the track order

You can check your programme before or after you

start playing.

Press CHECK.

Each time you press this button, the display shows the

track number in the programmed order. After the last

track in the programme, the display shows “End” and

returns to the original display. If you check the order

after you start playing, the display shows only the

remaining track numbers.

Total playing time

Programmed

tracks

25

8

PROGRAM

MIN SEC

STEP

To select a track with a number over 10

Use >10 button (see page 11).

If you’ve made a mistake

Press CLEAR, then press the correct track number.

Playing CDs

16

EN

CONTINUE

SHUFFLE

CLEAR

>10

Number

buttons

·

2 Press the number buttons of the tracks you want to

delete.

The track numbers disappear from the music

calendar after “OFF” appears for a while.

To delete a track numbered over 10, use the >10

button (see page 11).

If you’ve made a mistake

Press the number button of the track. “On” appears in

the display and the track will be restored.

3 After you’ve deleted all the tracks you don’t want,

press CONTINUE.

“SHUFFLE” disappears from the display.

If you press PLAY MODE on the player instead of

CONTINUE on the remote

The deleted tracks will be restored. Be sure to do this step

with the remote.

4 Press · to start Delete Play.

To cancel Delete Play

Press p in stop mode.

The player keeps the deleted tracks in memory even

after the Delete Play ends

When you press ·, you can play only the remaining

tracks again.

You can play the tracks in random order (Delete

Shuffle Play)

Just skip Step 3 in the above procedure.

You can delete a track while playing

Press CLEAR while the track is being played. The player

deletes the track and starts playing the next track.

You can store the deleted tracks of each disc

See “Storing Specific Tracks of a Disc” on page 24.

Playing Only Specific Tracks

(Delete Play)

You can delete unwanted tracks and play only the

remaining tracks.

Changing the track order

You can change your programme before you start

playing.

To

Erase a track

Erase the last track in the

programme

Add tracks to the end of

the programme

Change the whole

programme completely

You need to

Press CHECK until the track you

don’t want appears in the display,

then press CLEAR

Press CLEAR. Each time you press

the button, the last track will be

cleared.

Turn ≠ AMS ± until track

number you want to add appears,

then push ≠ AMS ±.

When using the remote, press the

number button of the tracks to be

added.

Hold down CLEAR until “ALL

CLr” appears in the display. Create

a new programme following the

programming procedure.

1 Press SHUFFLE.

“SHUFFLE” appears in the display.

Recording From CDs

17

EN

Recording Your Own

Programme

You can record the programme you’ve created on a

tape, DAT or MD. The programme can contain up to 24

tracks.

By inserting a pause during programming, you can

divide the programme into two for recording on both

sides of a tape.

1 Create your programme (for side A when

recording on a tape) while checking the total

playing time indicated in the display.

See “Creating Your Own Programme” on page 14.

2 When you record on both sides of the tape, press

∏ to insert a pause.

The “P” indication appears in the display and the

playing time is reset to “0.00.”

When you record on one side of the tape or on a

DAT or MD, skip this step and go to Step 4.

A pause is counted as one track

You can programme up to 23 tracks when you insert a

pause.

3 Repeat Step 1 to create the programme for side B.

4 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the

player pauses at the end of the programme for side

A.

5 When you record on side B, reverse the tape and

press · or ∏ on the player to resume playing.

To check and change your programme

See pages 15 and 16.

“SIDE-A” appears while checking the programme for

side A and “SIDE-B” while checking the programme for

side B.

You can automatically insert a blank space of 3

seconds between each track

Use the Auto Space function (see page 21).

CDP-XA50ES

∏·

CDP-XA30ES

∏

·

PLAY MODE

Recording From CDs

CHECK

CLEAR

≠ AMS ±

CHECK

CLEAR

≠ AMS ±

CONTINUE PROGRAM

Number

buttons

>10

P

=/+

CLEAR

CHECK

·

Recording From CDs

18

EN

1 Press EDIT/TIME FADE before you start playing

as follows:

• To select Time Edit, press the button once.

“EDIT” appears and “SIDE-A” flashes in the

display.

• To select Just Edit, press the button twice.

“

JUST

EDIT

( )

” appears and “SIDE-A” flashes in the

display.

2 Press 0 or ) to specify the tape length.

Each time you press these buttons, the display

changes as shown below, with the tape length of

one side following each indication.

n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - -. - - N

(23.00) (27.00) (30.00) (37.00) (45.00)

When you select “HALF”

The player sets the programme of each side to a half of

the total playing time of the disc. Note that you cannot

select “HALF” when the disc has more than 24 tracks.

3 Press EDIT/TIME FADE to have the player create

the programme.

The display shows the tracks to be recorded.

“SIDE-B” flashes in the display.

4 When you record on both sides of the tape, press

EDIT/TIME FADE again.

The player inserts a pause, then creates the

programme for side B. The display shows the

programmed tracks.

When you record on one side of the tape or on a

DAT or MD, skip this step.

5 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the

player pauses at the end of the programme for side

A.

6 When you record on side B, reverse the tape and

press · or ∏ on the player to resume playing.

To cancel Time Edit/Just Edit

Press PLAY MODE repeatedly until “SHUFFLE,”

“PROGRAM” and “CUSTOM INDEX” disappear from the

display (or press CONTINUE on the remote).

Recording a CD by Specifying

Tape Length (Time Edit/Just

Edit)

You can have the player create a programme that will

fit the length of the tape. Select one of the following

options:

• Time Edit: automatically creates a programme,

keeping the original order of the disc.

• Just Edit: automatically arranges the track order to fit

the tape length.

The programme can contain up to 24 tracks (a pause

inserted between tracks is counted as one track).

Note that tracks whose numbers are over 24 cannot be

programmed.

CDP-XA50ES

·

EDIT/TIME FADE

≠ AMS ±

∏

0/)

PLAY MODE

CDP-XA30ES

·

EDIT/TIME FADE

≠ AMS ±

∏

0/)

PLAY MODE

Recording From CDs

19

EN

You can programme the tracks you want in advance

Select the tracks before doing the above procedure. The

player creates a programme from the remaining tracks.

In this case, you cannot select “HALF” to specify the tape

length.

You can freely specify the tape length

Set the tape length using ≠ AMS ±.

Example: When the tape length of one side is 30 minutes

and 15 seconds

1 To set the minutes, turn ≠ AMS ±

until “30” appears in the display, then push

≠ AMS ±.

2 To set the seconds, turn ≠ AMS ±

until “15” appears in the display, then push

≠ AMS ±.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

You can automatically insert a blank space of 3

seconds between each track

Use the Auto Space function (see page 21).

You can check and change the programme

See pages 15 and 16.

Fading In or Out

You can manually fade in or out to prevent tracks from

starting or ending abruptly.

Note that you cannot use this effect when you use the

DIGITAL OUT connector.

CDP-XA50ES

EDIT/TIME FADE

·

0/)

FADER

Number

buttons

0/)

∏

CDP-XA30ES

0/)

·∏

EDIT/TIME FADE

·

P

Press FADER

During pause. “FADE” flashes and

play fades in.

When you want to start fading out.

“FADE” flashes. The play fades out

and the player pauses.

To

Start play fading in

End play fading out

Recording From CDs

20

EN

4 To record on side B, reverse the tape and press ·

or ∏ on the player to resume playing.

Again, the play fades out at the specified time.

To cancel Time Fade

Press EDIT/TIME FADE.

You can freely specify the playing time

See “You can freely specify the tape length” on page 19.

You can change discs during Time Fade

If the play ends before the specified fade-out time, (for

example, when you record CD-singles on a tape) change

the disc. The specified fade-out time is counted only

during playing.

You can fade in to resume playing in Step 4

After you reverse the tape, press FADER.

Note

If you press 0 or ) during Time Fade Play, Time Fade

will be cancelled.

Changing the fading time

You can change the fading time from 2 to 10 seconds

before fading in or out. If you don’t change it, fading

lasts for 5 seconds.

1 Press FADER before you start playing.

“5 SEC” appears and “FADE” flashes in the

display.

2 Press the number button to specify the fading time.

You can also specify the fading time by pressing

the 0/) buttons until the display shows the

time you want.

Fading out at the specified time

(Time Fade)

You can have the player fade out automatically by

specifying the playing time. Once you set the Time

Fade, it works twice, that is, the play fades out at the

end of both sides of a tape.

1 Press EDIT/TIME FADE three times before you

start playing.

“

TIME

FADE

( )

” and “SIDE-A” appear in the display.

2 Press 0 or ) to specify the playing time.

Each time you press these buttons, the display

changes as shown below, with the playing time of

one side following each indication.

n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - -. - - N

(23.00) (27.00) (30.00) (37.00) (45.00)

When you select “HALF”

The player sets the playing time to a half of the total

playing time.

3 Press · to start playing.

At the specified time the play fades out with

“FADE” flashing in the display and the player

pauses. “SIDE-B” appears in the display.

La page charge ...

Sony CDP-XA30ES Manuel utilisateur

Ce manuel convient également à

Sony CDP-XA30ES Manuel utilisateur

dans d''autres langues

Documents connexes