Sony CDP-XA30ES Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

3-858-365-12 (1)
1997 by Sony Corporation
Operating Instructions
Mode d’emploi
Manual de instrucciones
Bruksanvisning
EN
F
ES
S
CDP-XA50ES
CDP-XA30ES
2
EN
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.
Do not install the
appliance in a confined
space, such as a bookcase
or built-in cabinet.
Welcome!
Thank you for purchasing the Sony
Compact Disc Player. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
About This Manual
The instructions in this manual are for
models CDP-XA50ES and CDP-XA30ES.
The CDP-XA50ES is the model used for
illustration purposes, unless otherwise
mentioned. Any difference in operation
is clearly indicated in the text, for
example, “CDP-XA50ES only.”
Conventions
Instructions in this manual describe
the controls on the player.
You can also use the controls on the
remote if they have the same or similar
names as those on the player.
The following icons are used in this
manual:
Indicates that you can do the
task using the remote.
Indicates hints and tips for
making the task easier.
This appliance is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
The following caution label is located
inside the unit.
Getting Started
EN
3
EN
Getting Started
Unpacking............................................................................................................................. 4
Hooking Up the System...................................................................................................... 4
Playing a CD............................................................................................................................. 6
Playing CDs
Customising the Sound of Your Music (Digital Filter Function).................................. 8
Using the Display .............................................................................................................. 10
Locating a Specific Track .................................................................................................. 11
Locating a Particular Point in a Track ............................................................................ 12
Playing Tracks Repeatedly ............................................................................................... 12
Playing in Random Order (Shuffle Play) .......................................................................13
Creating Your Own Programme (Programme Play) .................................................... 14
Playing Only Specific Tracks (Delete Play) Z .............................................................. 16
Recording From CDs
Recording Your Own Programme ..................................................................................17
Recording a CD by Specifying Tape Length (Time Edit/Just Edit) ........................... 18
Fading In or Out................................................................................................................. 19
Useful Tips for Recording Z ........................................................................................... 21
Storing Information About CDs (Custom Files)
What You Can Do With the Custom Files ..................................................................... 22
Indexing a Disc (Custom Index) ......................................................................................22
Storing Specific Tracks of a Disc (Delete Bank)............................................................. 24
Additional Information
Precautions ......................................................................................................................... 26
Notes on CDs...................................................................................................................... 26
Troubleshooting ................................................................................................................. 27
Specifications ...................................................................................................................... 27
Index
Index .................................................................................................................................... 28
TABLE OF CONTENTS
Getting Started
4
EN
LINE OUT
FIXED
CD
Unpacking
Check that you received the following items:
Audio connecting cord (1)
Remote commander (remote) (1)
Sony SUM-3 (NS) batteries (2)
Stabiliser (1)
Inserting batteries into the remote
You can control the player using the supplied remote.
Insert two R6 (size AA) batteries by matching the +
and – on the batteries. When using the remote, point it
at the remote sensor g on the player.
Hooking Up the System
Overview
This section describes how to hook up the CD player to
an amplifier. Be sure to turn off the power of each
component before making the connections.
When to replace batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the player,
replace all the batteries with new ones.
Notes
Do not leave the remote near an extremely hot or humid
place.
Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
To mains
CDP-XA50ES
DIGITAL OUT
COAXIAL
LINE OUT
VARIABLE
DIGITAL OUT
OPTICAL
To mains
Amplifier
To mains
CDP-XA30ES
DIGITAL OUT
COAXIAL
LINE OUT
VARIABLE
DIGITAL OUT
OPTICAL
To mains
Amplifier
: Signal flow
CD
LINE OUT
FIXED
: Signal flow
Getting Started
5
EN
Hookups
pWhen making analog hookups
When connecting an audio cord, be sure to match the
colour-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
Amplifier
AmplifierCD player
If you have an analog power amplifier
Connect the amplifier via the VARIABLE LINE OUT jacks
using the supplied audio cord. You can adjust the output
level with the LINE OUT/PHONE LEVEL control on the
player or the LINE OUT LEVEL buttons on the remote.
If you have a digital component with an optical digital
input connector
Connect the component via the DIGITAL OUT (OPTICAL)
connector using the optical cable (not supplied). Take off
the cap and plug in the optical cable.
CD player
Digital component
CD player
What cords will I need?
pWhen making analog hookups
Audio cord (supplied) (1)
White
(L)
Red
(R)
White
(L)
Red
(R)
pWhen making digital hookups
Optical cable POC-15 (not supplied)
Coaxial cable (not supplied)
LINE OUT
FIXED
L
R
L
R
VARIABLE
INPUT
CD
L
R
LINE OUT
FIXED
L
R
L
R
VARIABLE
INPUT
CD
L
R
DIGITAL OUT
OPTICAL COAXIAL
DIGITAL IN
OPTICAL
If you have a digital component with a coaxial digital
input connector
Connect the component via the DIGITAL OUT (COAXIAL)
connector using the coaxial cable (not supplied).
Digital component
CD player
Note
When you connect via the DIGITAL OUT connector, noise
may occur when you play CD software other than music, such
as a CD-ROM.
pWhen making digital hookups
You can avoid deterioration of the signal during
transmission, since the music signal output through
the digital output connectors retains digital form.
You can connect a digital component such as a
digital amplifier, D/A converter, DAT or MD. When
you connect a DAT or MD, you can make digital
recordings from CDs.
Note that you cannot use fading in or out function
(page 19) when making this connection.
DIGITAL IN
COAXIAL
DIGITAL OUT
OPTICAL COAXIAL
Setting the voltage selector (voltage
selector equipped models only)
Check that the voltage selector on the rear panel of the
player is set to the local power line voltage. If not, set
the selector to the correct position using a screwdriver
before connecting the mains lead to a wall outlet.
Connecting the mains lead
Connect the mains lead to a wall outlet.
Removing the notice sheet
The notice sheet is put on the player. Remove the sheet
before you use your player.
220 - 240 V110 - 120 V
Basic Operations
6
EN
Playing a CD
23
1
2
See pages 4 – 5 for the hookup
information.
If you turn on the player with
a CD in the tray
You can start playing
automatically from the
beginning of the CD. If you
connect a commercially
available timer, you can start
playing the CD at any time
you want.
Turn on the amplifier and select the CD player position.
Press POWER to turn on the player.
4
CHECK CLEAR FILTER
PUSH ENTER
AMS
REPEAT TIME
TIME FADE FILE ERASE
EDIT/
PHONE LEVEL
LINE OUTPHONES
POWER
010
OPEN/CLOSE
MODE
PLAY
Connect the
headphones.
Adjust the
headphones volume.*
CHECK CLEAR FILTER
OPEN/CLOSE
REPEAT
FILE ERASE
TIME FADE
EDIT/
PUSH ENTER
AMS
TIME
PHONE LEVEL
LINE OUT
010
PHONES
POWER
PLAY MODE
234
Connect the
headphones.
Adjust the
headphones volume.*
CDP-XA50ES
CDP-XA30ES
*The output level from the LINE OUT
VARIABLE jacks will also change.
Basic Operations
Basic Operations
Basic Operations
7
EN
To stop playback
Press π.
When you want to
Pause
Resume play after pause
Go to the next track
Go back to the preceding track
Stop play and remove the CD
Press ·.
The disc tray closes and the player plays all the tracks once
(Continuous Play).
Adjust the volume on the amplifier.
4
You need to
Press
Press or ·
Turn AMS ± clockwise. (When
using the remote, press +.)
Turn AMS ± anticlockwise.
(When using the remote, press =.)
Press § OPEN/CLOSE
Press § OPEN/CLOSE, and place a CD on the tray.
3
With the label side up
Place the supplied stabiliser on the
CD. (The stabilisers supplied with the
CDP-XA50ES and CDP-XA30ES are
different.)
If––––– appears in the
display
Place the supplied stabiliser
on the CD.
If you do not, this indication
appears.
Note
In Step 3, do not place two or
more CDs at the same time.
If you do so, you may damage
the discs and/or the player.
If play doesn’t start from the
first track
Press PLAY MODE
repeatedly until
“SHUFFLE,” “PROGRAM”
and “CUSTOM INDEX”
disappear from the display
(or press CONTINUE on the
remote).
Playing CDs
8
EN
-120
0
0
22.05k
Customising the Sound of Your
Music (Digital Filter Function)
This player has a variable coefficient (V.C.) digital
filter. By selecting the type of filter you want, you can
adjust the sound to match your system, your room, the
music source, etc.
Selecting the filter directly on the player
1 Press FILTER.
The display shows the currently selected filter
number and the filter indicator flashes.
2 Turn AMS ± until the digital filter number
you want appears in the display.
As you turn the AMS ± control, the digital
filter number changes cyclically as follows:
If you are playing a disc, the sound will be
interrupted momentarily.
AMS ±FILTER
CDP-XA50ES
AMS ±FILTER
CDP-XA30ES
3 Push AMS ± to select the filter.
The original display reappears.
The selected digital filter number is stored in
memory even if you turn off the power.
You can also change the digital filter number by
pressing the FILTER button while the indicator is
flashing
Selecting the filter using the remote Z
1 Press DIGITAL FILTER.
The display shows the currently selected filter
number and the filter indicator flashes.
2 Press DIGITAL FILTER repeatedly until the
display shows the digital filter number you want.
The digital filter number is stored and the original
display reappears.
What is a variable coefficient (V.C.) digital
filter?
CD players use digital filters to eliminate the noise
generated during sampling. You can change the tone of
your music by changing the cutoff characteristics of the
digital filter.
This player has five types of filters with different
coefficient characteristics: “STD,” “1,” “2,” “3” and “4.”
In addition, digital filters “3” and “4” each have three
coefficient patterns, A–C, for more detailed
adjustments.
The following explains the terms you need to know to
understand the characteristics of the digital filters used
in this player.
Sharp roll-off and slow roll-off
Digital filters can be roughly classified into sharp roll-
off types and slow roll-off types, according to their
cutoff characteristics.
Response
(dB)
(Slow roll-off filter)
(Sharp roll-off filter)
Frequency (Hz)
Comparison of cutoff characteristics for sharp roll-off filter
and slow roll-off filter
DIGITAL FILTER
n STD n 1 n 2 n 3A n 3b n 3C n 4A n 4b n 4C
Playing CDs
Playing CDs
9
EN
Cascade type and direct type
There are two methods of digital filter oversampling:
the cascade type and direct type. The cascade type
multiplies the signal by eight in three stages, and the
direct type multiplies the signal by eight in one step.
Cascade filters have a high calculation efficiency, and
can realise steep, high-precision sharp roll-off
characteristics. Moreover, the ICs in this player use the
full feed-forward (FF) method between each of the
stages to improve the accuracy of the information
transfer.
On the other hand, eightfold oversampling data can be
obtained in one step with direct filters and there is no
loss during transfer between calculation stages.
However, since such circuits are extremely large, this
player can only support slow roll-off filters.
2 2 2
8
Characteristics of each digital filter
The following are the settings and characteristics for
each of the five digital filters. Use this information to
select the filter you want.
STD: Standard
This is a sharp roll-off, cascade type filter. It has the
same characteristics as the digital filters that have long
been used in Sony’s high-end units and has a sharp
cutoff that reaches –120 dB at 24 kHz. This filter uses
the full feed-forward method between the calculation
stages and gives the sound a wide range and ample
spatial representation.
1: Spline
This is a slow roll-off, cascade type filter that uses a
cubic spline function for interpolation. The spline
function features smoother connections between
points, and among spline functions, the cubic filter is
the most straightforward. Ringing in the impulse
response for this filter is much lower than for a sharp
roll-off type filter. With this filter, the sound image is
clear and sound reproduction is smooth.
2: Plain
This is a slow roll-off, direct type filter. It features an
absence of quantization between the digital filter
output and the D/A converter input.
Direct type calculations are used within the digital
filter and the bit length for the digital filter output and
the D/A converter input are the same, so no
requantization noise is generated between the digital
filter and the D/A converter. This means that, of the
16-bit information taken from the disc, elements up to
20 kHz are input as far as the D/A converter without
any nonlinear operation. This reproduces a sound with
high clarity and strength.
Sharp roll-off filter
Slow roll-off filter
Pre-ringing Post-ringing Pre-ringing
Post-ringing
Comparison of impulse response for sharp roll-off filter
and slow roll-off filter
IN OUT
FF FF
Sharp roll-off filters steeply cut off the noise generated
during sampling over 22.05 kHz. This is a superior way
of completely reproducing signals below 20 kHz: the
basic principle behind digital audio.
On the other hand, slow roll-off filters cut off the noise
generated during sampling gradually, and are able to
hold pre-ringing and post-ringing (a kind of sound
smearing) in the impulse response signal to a
minimum.
Playing CDs
10
EN
Using the Display
You can check information about the disc using the
display.
CDP-XA50ES
TIME
DISPLAY MODE
Checking the total number and playing
time of the tracks
Press TIME before you start playing.
The display shows the total number of tracks, total
playing time and music calendar.
Total playing timeTotal number of
tracks
Music calendar
TIME
CDP-XA30ES
TIME
12345
678910
MIN SEC
3: Analog type
This is a slow roll-off, direct type filter that simulates a
seventh-order analog Butterworth filter. This filter
completely prevents pre-ringing in the impulse
response. Also, since it simulates an analog filter, the
high-region phase outside the audible frequency is
rotated. The filters from 3A to 3C differ in degree of
phase rotation. 3A is multiplied by one (the true analog
characteristic), 3b is multiplied by 0.75, and 3C is
multiplied by 0.5. The impulse response changes as
shown in the figures below. The degree of pre-ringing
and post-ringing varies with the degree of phase
change. This gives the sound a feeling of warmth and
depth.
4: Butterworth
This is a slow roll-off, direct type filter and includes
fifth-order through ninth-order Butterworth filters.
However, the phase is linear and does not include the
phase change possibilities of filter 3 (analog type). As
the figure below shows, only the cutoff characteristics
can be changed in the fifth-order (4A), the seventh-
order (4b) and the ninth-order (4C). Ringing in the
impulse response increases from the fifth-order filter to
the ninth-order filter. This filter gives the sound a
feeling of balance and comfort.
Note
The Digital Filter function primarily changes characteristics
outside the audible frequency. They cannot affect changes
within the audible frequency such as those provided by the
tone controls of the amplifier. Therefore, with certain
combinations of hardware and software, there may be no
noticeable effect after switching the filter.
20k
Comparison of filter 4 cutoff characteristics
Frequency (Hz)
Comparison of filter 3 impulse response
3A 3b 3C
Response
(dB)
4A
4b
4C
Playing CDs
11
EN
While in Shuffle Play mode (“SHUFFLE” appears in
the display; see page 13), a one-second access time
blank is added between each track. This increase is
automatically added to the total playing time in the
display.
If the disc has more than 15 tracks, the z indication
appears next to 15 on the music calendar.
The information also appears when you press
§ OPEN/CLOSE to close the disc tray.
Display information while playing a disc
While playing a disc, the display shows the current
track number, index number, playing time and the
music calendar.
Current track
number
Playing time
Music calendar
Index number (page 12) or Custom Index
number (page 22)
The track numbers in the music calendar disappear
after they are played.
Checking the remaining time
Each time you press TIME while playing a disc, the
display changes as shown in the chart below.
If the remaining time exceeds 100 minutes
in programme mode, “––.–– appears
instead of the remaining time.
Press
Press
Playing time
and number
of the current
track
Remaining
time on the
current
track
Remaining
time on the
disc
Press
12345
678910
MIN SECINDEX
Locating a Specific Track
You can quickly locate any track while playing a disc
using the AMS (Automatic Music Sensor) on the player
or number buttons on the remote.
Number
buttons
>10
=/+
To locate
The next or
succeeding tracks
The current or
preceding tracks
A specific track
directly Z
When you directly locate a track numbered over 10
Z
Press >10 first, then the corresponding number buttons
on the remote. To enter “0,” use button 10.
Example: To play track number 30
Press >10 first, then 3 and 10.
You need to
Turn AMS ± clockwise until
you find the track. When using the
remote, press + repeatedly until you
find the track.
Turn AMS ± anticlockwise
until you find the track. When using
the remote, press = repeatedly until
you find the track.
Press the number button of the track
on the remote
AMS ±
Turning off the music calendar in the
display
Each time you press DISPLAY MODE on the remote
while playing a disc, the music calendar turns off and
on alternately in the display.
12345
678910
MIN SECINDEX
12345
678910
MIN SECINDEX
12345
678910
MIN SEC
Playing CDs
12
EN
Playing Tracks Repeatedly
You can play tracks repeatedly in any play mode.
REPEAT
A˜B
REPEAT
Press REPEAT while playing a disc.
“REPEAT” appears in the display. The player repeats
the tracks as follows:
When the disc is played in
Continuous Play (page 6)
Shuffle Play (page 13)
Programme Play (page 14)
Delete Play (page 16)
Delete Shuffle Play
(page 14, 16)
Custom Index Play
(page 23)
To cancel Repeat Play
Press REPEAT repeatedly until “REPEAT” disappears from
the display.
The player repeats
All the tracks
All the tracks in random
orders
The same programme
All the remaining tracks
All the remaining tracks in
random orders
The portion between two
indexes
CDP-XA50ES
CDP-XA30ES
REPEAT
Locating a Particular Point in a
Track
You can also locate a particular point in a track while
playing a disc.
0/)
INDEX Ç/ç
0/)
To locate a point
While monitoring the
sound
Quickly by observing
the display during
pause
Using an index (only
for indexed discs)
What is an index?
It is a number that divides a track or a disc into sections,
enabling you to easily locate a desired point. You can
determine if a disc uses indexes by its packaging.
Note
If “ ” appears in the display, the disc has reached the end
while you were pressing ). Press 0 or turn
AMS ± anticlockwise to go back.
Press
) (forward) or 0 (backward)
and hold down until you find the
point
0/) and hold down until you
find the point. You will not hear the
sound during the operation.
INDEX Ç/ç on the remote
repeatedly until you find the point
Playing CDs
13
EN
Repeating the current track
You can repeat only the current track.
While the track you want is being played, press
REPEAT repeatedly until “REPEAT 1” appears in the
display.
Note
You cannot repeat the current track while the disc is played in
Custom Index Play mode (see page 23).
Repeating a Specific Portion (A˜B Repeat)
You can play a specific portion in a track repeatedly.
This might be useful when you want to memorise
lyrics.
Note that you cannot repeat a portion extending to two
tracks.
1 While playing a disc, press A˜B on the remote
when you find the starting point (point A) to be
played repeatedly.
“A-” of “REPEAT A-” flashes in the display.
2 When you reach the ending point (point B), press
A˜B again.
“REPEAT A-B” appears. The player plays this
specific portion repeatedly.
To cancel A˜B Repeat
Press REPEAT.
Setting a new starting point
You can move the repeating portion ahead by
changing the starting point.
1 Press A˜B while the player is repeating the
specific portion.
The ending point B becomes the new starting point
A. “A-” of “REPEAT A-” flashes in the display.
2 When you reach the ending point (point B), press
A˜B again.
“REPEAT A-B” appears. The player repeats
between the new starting and ending points.
When you want to restart from the starting point A
Press · during A˜B Repeat.
Playing in Random Order
(Shuffle Play)
You can have the player “shuffle” tracks and play in a
random order.
·
PLAY MODE
·
PLAY MODE
1 Press PLAY MODE repeatedly until “SHUFFLE”
appears in the display.
When using the remote, press SHUFFLE.
2 Press · to start Shuffle Play.
The
indication appears while the player is
“shuffling” the tracks.
To cancel Shuffle Play
Press PLAY MODE four times (or CONTINUE on the remote).
CDP-XA30ES
CDP-XA50ES
SHUFFLE
CONTINUE
·
Playing CDs
14
EN
PLAY MODE
Creating Your Own
Programme (Programme Play)
You can arrange the order of the tracks on a disc and
create your own programme. The programme can
contain up to 24 tracks.
PLAY MODE
CDP-XA50ES
CDP-XA30ES
CONTINUE
Number
buttons
>10
·
=/+
2 Turn AMS ± until the track number you
want appears in the display.
The playing order and the track numbers being
programmed flash and the total playing time
including the track appears in the display.
AMS ±
CHECK
π
·
CLEAR
CHECK
π
·
CLEAR
AMS ±
PROGRAM
CLEAR
CHECK
p
Track numbers being
programmed
25
8
PROGRAM
MIN SEC
STEP
Total playing time
Playing order
Programmed tracks
3 Push AMS ± to select the track.
Last programmed
track
Playing order
Programmed
tracks
Total playing time
25
8
PROGRAM
MIN SEC
STEP
Creating a programme on the player
1 Press PLAY MODE repeatedly until “PROGRAM”
appears in the display before you start playing.
12345
678910
PROGRAM
You can start Shuffle Play while playing
Press PLAY MODE once (or SHUFFLE on the remote),
and Shuffle Play starts from the current track.
You can delete unwanted tracks during Shuffle Play
(Delete Shuffle Play)
Press the number button of the track you want to delete
on the remote.
The track number and “OFF” appear in the display, and
then the track number disappears from the music
calendar.
If you want to restore the track, press the number button
again.
To restore all the tracks, press π in stop mode.
If you’ve made a mistake
Press CLEAR, then repeat Steps 2 and 3.
Playing CDs
15
EN
4 Repeat Steps 2 and 3 to programme the tracks in
the order you want.
5 Press · to start Programme Play.
To cancel Programme Play
Press PLAY MODE three times.
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
The programme remains even after the Programme
Play ends
When you press ·, you can play the same programme
again.
Notes
––.–– appears instead of the total playing time in the
display when it exceeds 100 minutes.
“FULL” appears in the display when you try to add a track
to a programme which already contains 24 tracks.
Creating a programme using the remote
1 Press PROGRAM before you start playing.
“PROGRAM” appears in the display.
2 Press number buttons of the tracks you want to
programme in the order you want.
Example: To programme the tracks 2, 8 and 5
Press number buttons in the order 2, 8
and 5.
Last programmed
track
Playing order
3 Press · to start Programme Play.
To cancel Programme Play
Press CONTINUE.
You can check the total playing time while
programming using the remote (Programme Edit)
To select a track, press = or + and check the total
playing time. Then press PROGRAM to confirm your
selection.
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
The programme remains even after the Programme
Play ends
When you press ·, you can play the same programme
again.
Notes
––.–– appears instead of the total playing time in the
display when it exceeds 100 minutes.
“FULL” appears in the display when you try to add a track
to a programme which already contains 24 tracks.
Checking the track order
You can check your programme before or after you
start playing.
Press CHECK.
Each time you press this button, the display shows the
track number in the programmed order. After the last
track in the programme, the display shows “End” and
returns to the original display. If you check the order
after you start playing, the display shows only the
remaining track numbers.
Total playing time
Programmed
tracks
25
8
PROGRAM
MIN SEC
STEP
To select a track with a number over 10
Use >10 button (see page 11).
If you’ve made a mistake
Press CLEAR, then press the correct track number.
Playing CDs
16
EN
CONTINUE
SHUFFLE
CLEAR
>10
Number
buttons
·
2 Press the number buttons of the tracks you want to
delete.
The track numbers disappear from the music
calendar after “OFF” appears for a while.
To delete a track numbered over 10, use the >10
button (see page 11).
If you’ve made a mistake
Press the number button of the track. “On” appears in
the display and the track will be restored.
3 After you’ve deleted all the tracks you don’t want,
press CONTINUE.
“SHUFFLE” disappears from the display.
If you press PLAY MODE on the player instead of
CONTINUE on the remote
The deleted tracks will be restored. Be sure to do this step
with the remote.
4 Press · to start Delete Play.
To cancel Delete Play
Press p in stop mode.
The player keeps the deleted tracks in memory even
after the Delete Play ends
When you press ·, you can play only the remaining
tracks again.
You can play the tracks in random order (Delete
Shuffle Play)
Just skip Step 3 in the above procedure.
You can delete a track while playing
Press CLEAR while the track is being played. The player
deletes the track and starts playing the next track.
You can store the deleted tracks of each disc
See “Storing Specific Tracks of a Disc” on page 24.
Playing Only Specific Tracks
(Delete Play)
You can delete unwanted tracks and play only the
remaining tracks.
Changing the track order
You can change your programme before you start
playing.
To
Erase a track
Erase the last track in the
programme
Add tracks to the end of
the programme
Change the whole
programme completely
You need to
Press CHECK until the track you
don’t want appears in the display,
then press CLEAR
Press CLEAR. Each time you press
the button, the last track will be
cleared.
Turn AMS ± until track
number you want to add appears,
then push AMS ±.
When using the remote, press the
number button of the tracks to be
added.
Hold down CLEAR until “ALL
CLr” appears in the display. Create
a new programme following the
programming procedure.
1 Press SHUFFLE.
“SHUFFLE” appears in the display.
Recording From CDs
17
EN
Recording Your Own
Programme
You can record the programme you’ve created on a
tape, DAT or MD. The programme can contain up to 24
tracks.
By inserting a pause during programming, you can
divide the programme into two for recording on both
sides of a tape.
1 Create your programme (for side A when
recording on a tape) while checking the total
playing time indicated in the display.
See “Creating Your Own Programme” on page 14.
2 When you record on both sides of the tape, press
to insert a pause.
The “P” indication appears in the display and the
playing time is reset to “0.00.”
When you record on one side of the tape or on a
DAT or MD, skip this step and go to Step 4.
A pause is counted as one track
You can programme up to 23 tracks when you insert a
pause.
3 Repeat Step 1 to create the programme for side B.
4 Start recording on the deck and then press · on
the player.
When you record on both sides of the tape, the
player pauses at the end of the programme for side
A.
5 When you record on side B, reverse the tape and
press · or on the player to resume playing.
To check and change your programme
See pages 15 and 16.
“SIDE-A” appears while checking the programme for
side A and “SIDE-B” while checking the programme for
side B.
You can automatically insert a blank space of 3
seconds between each track
Use the Auto Space function (see page 21).
CDP-XA50ES
·
CDP-XA30ES
·
PLAY MODE
PLAY MODE
Recording From CDs
CHECK
CLEAR
AMS ±
CHECK
CLEAR
AMS ±
CONTINUE PROGRAM
Number
buttons
>10
P
=/+
CLEAR
CHECK
·
Recording From CDs
18
EN
1 Press EDIT/TIME FADE before you start playing
as follows:
To select Time Edit, press the button once.
“EDIT” appears and “SIDE-A” flashes in the
display.
To select Just Edit, press the button twice.
JUST
EDIT
( )
” appears and “SIDE-A” flashes in the
display.
2 Press 0 or ) to specify the tape length.
Each time you press these buttons, the display
changes as shown below, with the tape length of
one side following each indication.
n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - -. - - N
(23.00) (27.00) (30.00) (37.00) (45.00)
When you select “HALF”
The player sets the programme of each side to a half of
the total playing time of the disc. Note that you cannot
select “HALF” when the disc has more than 24 tracks.
3 Press EDIT/TIME FADE to have the player create
the programme.
The display shows the tracks to be recorded.
“SIDE-B” flashes in the display.
4 When you record on both sides of the tape, press
EDIT/TIME FADE again.
The player inserts a pause, then creates the
programme for side B. The display shows the
programmed tracks.
When you record on one side of the tape or on a
DAT or MD, skip this step.
5 Start recording on the deck and then press · on
the player.
When you record on both sides of the tape, the
player pauses at the end of the programme for side
A.
6 When you record on side B, reverse the tape and
press · or on the player to resume playing.
To cancel Time Edit/Just Edit
Press PLAY MODE repeatedly until “SHUFFLE,”
“PROGRAM” and “CUSTOM INDEX” disappear from the
display (or press CONTINUE on the remote).
Recording a CD by Specifying
Tape Length (Time Edit/Just
Edit)
You can have the player create a programme that will
fit the length of the tape. Select one of the following
options:
Time Edit: automatically creates a programme,
keeping the original order of the disc.
Just Edit: automatically arranges the track order to fit
the tape length.
The programme can contain up to 24 tracks (a pause
inserted between tracks is counted as one track).
Note that tracks whose numbers are over 24 cannot be
programmed.
CDP-XA50ES
·
EDIT/TIME FADE
AMS ±
0/)
PLAY MODE
CDP-XA30ES
·
EDIT/TIME FADE
AMS ±
0/)
PLAY MODE
Recording From CDs
19
EN
You can programme the tracks you want in advance
Select the tracks before doing the above procedure. The
player creates a programme from the remaining tracks.
In this case, you cannot select “HALF” to specify the tape
length.
You can freely specify the tape length
Set the tape length using AMS ±.
Example: When the tape length of one side is 30 minutes
and 15 seconds
1 To set the minutes, turn AMS ±
until “30” appears in the display, then push
AMS ±.
2 To set the seconds, turn AMS ±
until “15” appears in the display, then push
AMS ±.
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
You can automatically insert a blank space of 3
seconds between each track
Use the Auto Space function (see page 21).
You can check and change the programme
See pages 15 and 16.
Fading In or Out
You can manually fade in or out to prevent tracks from
starting or ending abruptly.
Note that you cannot use this effect when you use the
DIGITAL OUT connector.
CDP-XA50ES
EDIT/TIME FADE
·
0/)
FADER
Number
buttons
0/)
CDP-XA30ES
0/)
·∏
EDIT/TIME FADE
·
P
Press FADER
During pause. “FADE” flashes and
play fades in.
When you want to start fading out.
“FADE” flashes. The play fades out
and the player pauses.
To
Start play fading in
End play fading out
Recording From CDs
20
EN
4 To record on side B, reverse the tape and press ·
or on the player to resume playing.
Again, the play fades out at the specified time.
To cancel Time Fade
Press EDIT/TIME FADE.
You can freely specify the playing time
See “You can freely specify the tape length” on page 19.
You can change discs during Time Fade
If the play ends before the specified fade-out time, (for
example, when you record CD-singles on a tape) change
the disc. The specified fade-out time is counted only
during playing.
You can fade in to resume playing in Step 4
After you reverse the tape, press FADER.
Note
If you press 0 or ) during Time Fade Play, Time Fade
will be cancelled.
Changing the fading time
You can change the fading time from 2 to 10 seconds
before fading in or out. If you don’t change it, fading
lasts for 5 seconds.
1 Press FADER before you start playing.
“5 SEC” appears and “FADE” flashes in the
display.
2 Press the number button to specify the fading time.
You can also specify the fading time by pressing
the 0/) buttons until the display shows the
time you want.
Fading out at the specified time
(Time Fade)
You can have the player fade out automatically by
specifying the playing time. Once you set the Time
Fade, it works twice, that is, the play fades out at the
end of both sides of a tape.
1 Press EDIT/TIME FADE three times before you
start playing.
TIME
FADE
( )
” and “SIDE-A” appear in the display.
2 Press 0 or ) to specify the playing time.
Each time you press these buttons, the display
changes as shown below, with the playing time of
one side following each indication.
n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - -. - - N
(23.00) (27.00) (30.00) (37.00) (45.00)
When you select “HALF”
The player sets the playing time to a half of the total
playing time.
3 Press · to start playing.
At the specified time the play fades out with
“FADE” flashing in the display and the player
pauses. “SIDE-B” appears in the display.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Sony CDP-XA30ES Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à