mothercare Chauffe-biberon rapide Avent Manuel utilisateur

SCF358

EN User manual 2

ES-MX Manual del usuario 19

FR-CA Mode d’emploi 38

PT-BR Manual do utilizador 57

2 ENGLISH

Contents

IMPORTANT SAFEGUARDS 3

Introduction 6

Instructions for use 6

Cleaning and descaling 14

Disposal 16

Troubleshooting 16

Warranty and support 18

3ENGLISH

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be

followed including the following:

Read all instructions.

Danger

- To protect against electrical shock, do not immerse the

cord, plug or appliance in water or other liquid.

Warning

- Only use the appliance indoors.

- Do not let the power cord hang over the edge of a table

or worktop. Store excess cord in the base of the bottle

warmer.

- A short power-supply cord is provided to reduce the risk

resulting from becoming entangled in or tripping over a

longer cord.

- If extension cord is used: The cord should be arranged

so that it will not drape over the countertop or tabletop

where it can be pulled on by children or tripped over

unintentionally.

- The marked electrical rating of the cord set or extension

cord should be at least as great as the electrical rating of

the appliance.

- Keep the power cord away from hot surfaces.

- Only connect the appliance to a grounded wall socket.

Always make sure that the plug is inserted into the wall

socket properly.

- Before you connect the appliance, check that the voltage

indicated on the bottom of the appliance corresponds to

the local voltage.

- If you need to use an extension cord, make sure it is

a grounded extension cord with a rating of at least

13 amperes.

4 ENGLISH

- Extension cords may be used if care is exercised in their

use.

- Do not use the appliance if the plug, the power cord

or the appliance itself is damaged. If the power cord is

damaged, you must have it replaced by Philips, a Philips

authorized service center or similarly qualied persons in

order to avoid a hazard.

- Do not place the appliance on or near a hot gas or

electric cooker, or in a heated oven.

- This appliance can be used by persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved.

- Children must not play with the appliance.

- Close supervision is necessary when any appliance is

used by or near children.

- Do not spill water on the power plug.

- Only use the appliance as described in the user manual

to avoid injury due to misuse.

- Do not preheat the appliance.

- Always place a fully assembled bottle with cap in the

bottle warmer before you add water.

- Make sure you add water before you switch on the bottle

warmer.

- Hot water can cause serious burns. Be careful when the

bottle warmer contains hot water.

- The accessible surfaces of the appliance may become

hot during use and are subject to residual heat after use.

- Do not move the appliance when it contains hot water.

- When the food or milk has reached the required

temperature, remove the bottle or container from the

bottle warmer.

5ENGLISH

- If the appliance is of the grounded type, the cord set or

extension cord should be a grounding-type 3-wire cord.

- Unplug from outlet when not in use and before cleaning.

Allow to cool before putting on or taking o parts.

- The use of accessory attachments not recommended by

the appliance manufacturer may cause injuries.

- To disconnect, turn any control to “o”, then remove plug

from wall outlet.

- Before serving be sure food is at safe temperature.

- Before serving, unplug cord form wall outlet and dish. Do

not leave cord within child’s reach.

Caution

- This appliance is intended for use in household.

- The food should not be heated for too long.

- Always check the food temperature before you feed

your child. Gently swirl the bottle and check by sprinkling

a few drops on the inside of your wrist. (Follow the

instructions in section ‘‘Feed your baby the milk’’.)

- Unplug the appliance when it is not in use.

- The surface of the heating element is subject to residual

heat after use.

- Let the appliance cool down before you clean it.

- Follow the descaling instructions to avoid irreparable

damage.

- Do not try to open or repair the appliance yourself.

Contact the Philips Consumer Care Center in your

country (see www.philips.com/support).

SAVE THESE INSTRUCTIONS

The production date code YYWW is located in the cord storage compartment in the

base of the bottle warmer.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and regulations

regarding exposure to electromagnetic elds.

6 ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips Avent! To fully benet

from the support that Philips Avent oers, register your product at

www.philips.com/welcome.

With this bottle warmer, you can warm and defrost milk in Philips Avent and other

most common branded feeding bottles and baby food in containers.

To help preserve the quality of your breast milk, it is important to warm the milk

in a safe and controlled way. The built-in sensor tracks the temperature to avoid

overheating.

Instructions for use

Product overview

A

B

CD

F

E

A Bottle warmer D Keep warm / defrost setting

B Progress indicator E Milk volume setting

C Baby food warming setting F On / o button

7ENGLISH

Explanation of settings

Milk volume

• Select the milk volume you want to warm. You

can set from 30 ml / 1 oz up to 330 ml / 11 oz.

The bottle warmer warms the milk to

approximately body temperature. It then

switches to keep warm mode automatically for

about 60 minutes.

Baby food warming

• Select this setting to warm baby food.

Keep warm / defrost

• The built-in sensor detects the milk / baby

food temperature to nd the optimal setting. If

the milk / baby food is warm, it will be warmed

gradually and kept at the right temperature.

If the milk / baby food is frozen, it will be

defrosted to liquid state and then warmed to

the right temperature.

When the entire progress indicator is on but not ashing, the milk / food is ready

for feeding. Feed your baby when the milk / food is warmed. Do not rewarm the

milk / food after it has cooled down, as bacteria may start to develop in it.

Warm milk

1

Place the bottle in the bottle warmer. Fill with drinking water to the level of

the milk. If you have a large volume of milk, ll with water to approximately

1 cm below the top of the bottle warmer.

2

Select the desired setting based on the milk volume and press the on / o

button to switch on.

7

210

7oz

210ml

8 ENGLISH

3

The progress indicator ashes gradually to show the progress of milk

warming.

4

When the entire progress indicator lights up continuously, the milk is ready

for feeding and the bottle warmer automatically switches to keep warm

mode.

5

The bottle warmer switches o automatically after about 60 minutes,

including warming time. The progress indicator turns o.

60 min

Tip

• If you want the milk warmer, keep the bottle in the appliance until it reaches the desired

temperature after the entire progress indicator lights up.

• If you are using a milk bag, select the keep warm / defrost setting because it takes less

power to warm milk bags.

• If you are using a silicone bottle, it takes longer to warm milk. Keep it in the bottle warmer

for 3-4 minutes after the entire progress indicator lights up.

Recommended setting for dierent containers

Container Recommended Setting

Plastic Milk volume setting

Glass Milk volume setting

Silicone Milk volume setting + 3-4 minutes

Milk bag Keep warm/ Defrost setting

Check the instructions of your milk bag and make sure it can be warmed in a bottle

warmer.

Note

• The time to warm milk depends on the volume, initial temperature and bottle material.

9ENGLISH

Feed your baby the milk

Press the on / o button to switch o the appliance and take out the milk bottle.

Note

• If you are using a small bottle, such as a 2 oz bottle, be careful to avoid touching the hot

water when you remove the bottle.

Always check the temperature of the milk before you feed your baby. Gently swirl

the bottle and check by sprinkling a few drops on the inside of your wrist.

Reuse the bottle warmer right away for another bottle

If you want to warm another bottle, let the bottle warmer cool down for a few

minutes. To speed up, ll the bottle warmer with fresh cold water.

When you switch on the bottle warmer, the progress indicator ashes gradually to

indicate that the appliance is warming again.

Note

• If the progress indicator is on but not ashing, the bottle warmer is still too hot to warm

another bottle. Switch o the bottle warmer and let it cool down for a few minutes.

10 ENGLISH

Warm baby food

1

Place the baby food container in the bottle warmer. Fill with drinking water

to the level of the baby food. If you have a large volume of baby food, ll with

water to approximately 1 cm below the top of the bottle warmer.

2

Select the baby food warming setting and press the on / o button to switch

on.

3

The progress indicator ashes to show it is in the warming process.

Note

• Due to variations in baby food consistency, it is not possible for the appliance to detect

precisely how long the baby food should be warmed.

4

Stir the baby food while the jar or container is in the bottle warmer. For

optimal result, check its temperature while it is warming up.

» Be careful not to burn your ngers when holding the container or jar while

stirring.

5

When the entire progress indicator lights up continuously, the baby food

is ready for feeding and the bottle warmer automatically switches to keep

warm mode.

11ENGLISH

6

The bottle warmer switches o automatically after about 60 minutes,

including warming time. The progress indicator turns o.

60 min

Feed your baby the baby food

Press the on / o button to switch o the appliance and take out the food

container or jar.

Always check the temperature of the baby food before you feed your baby. Gently

stir the baby food in the food container or jar and taste it to make sure it is not

too hot.

Reuse the bottle warmer right away for another container of baby

food

Follow the same steps as indicated in the section “Warm milk”

12 ENGLISH

Keep warm

With this setting, the built-in sensor detects the milk temperature to switch to the

optimal setting. If you put warm milk into the appliance, it is warmed gradually and

kept at the right temperature.

1

Place the bottle in the bottle warmer. Fill with drinking water to the level of

the milk. If you have a large volume of milk, ll with water to approximately

1 cm below the top of the bottle warmer.

2

Select the keep warm / defrost setting and press the on / o button to

switch on.

3

The progress indicator ashes to show that milk is warming.

4

When the entire progress indicator lights up continuously, the milk is ready

for feeding and the bottle warmer keeps the milk at this temperature.

13ENGLISH

5

The bottle warmer switches o automatically after about 60 minutes,

including warming time. The progress indicator turns o.

60 min

Note

• The time may vary depending on the milk volume and starting temperature.

Defrost

With this setting, the built-in sensor detects the milk / food temperature to nd

the optimal setting. If you put frozen milk / baby food into the appliance, the bottle

warmer defrosts the milk / baby food to liquid state and then warms it to the right

temperature.

1

Place the bottle in the bottle warmer. Fill with drinking water to the level of

the milk. If you have a large volume of milk, ll with water to approximately

1 cm below the top of the bottle warmer.

2

Select the keep warm / defrost setting and press the on / o button to

switch on.

14 ENGLISH

3

The progress indicator ashes to show that milk is defrosting and warming.

4

When the entire progress indicator lights up continuously, the milk / baby

food is ready for feeding.

5

The bottle warmer switches o automatically after about 60 minutes,

including defrosting and warming time. The progress indicator turns o.

60 min

You can also defrost baby food in the Philips Avent food container with this

setting. Due to variations in baby food consistency, it is strongly recommended you

continuously stir and check the baby food while you are defrosting it for optimal

results.

Cleaning and descaling

Cleaning

1

Unplug the bottle warmer and let it cool down.

2

Pour out water sideways rather than forwards or backwards to keep water

from spilling onto the knob or main plug.

15ENGLISH

3

Wipe with a moist cloth.

» Do not use abrasive, antibacterial cleaning agents, chemical solvents or

sharp tools to clean the bottle warmer.

Note

• If you used the bottle warmer to warm baby food, make sure that no spilled baby food

remains at the bottom of the bottle warmer.

Descaling

It is recommended to descale the bottle warmer every four weeks to ensure it

works eciently.

To descale, mix 60 ml / 2 oz of white vinegar with 120 ml / 4oz of cold water. Switch

on and select the milk warming setting for contents under 180 ml / 6 oz and let the

appliance operate for 10 minutes. Leave the solution in the bottle warmer until all

scale has dissolved.

10 min

180ml

6oz

Note

• You can also use citric acid based descalers.

• Do not use other types of descalers.

Empty the bottle warmer and rinse the inside thoroughly with a moist cloth. If you

still see traces of scale, repeat the descaling procedure.

16 ENGLISH

Disposal

Your product is designed and manufactured with high quality materials and

components, which can be recycled and reused. For recycling information, please

contact your local waste management facilities or visit www.recycle.philips.com.

Troubleshooting

This chapter summarizes the most common problems you could encounter with

the appliance. If you are unable to resolve the problem with the information below,

contact the Consumer Care Center in your country.

Problem After switching on the bottle warmer, the entire progress indicator

blinks fast and switches o.

Cause

•

The temperature of water in the bottle warmer is too hot or too

cold.

•

The boil-dry protection is activated.

Solution

•

Switch o and unplug. Let it cool down for a few minutes. Make

sure you ll it with fresh room temperature water.

•

The bottle warmer automatically switches o if it is on and there

is no water or not enough water in it. Switch o and unplug. Let

it cool down rst. Make sure you ll it with enough fresh room

temperature water. The bottle warmer is ready to use again.

Problem The milk is too hot.

Cause

•

You may have selected an incorrect setting or are using a milk bag.

Solution

•

Select the milk volume setting based on the milk volume, not the

bottle size.

•

If you are using a milk bag, select the keep warm / defrost setting.

Problem The milk is still cold.

Cause

•

You may have selected an incorrect setting, are using a silicone

bottle, or have lled the bottle warmer with warm water.

Solution

•

Select the milk volume setting based on the milk volume, not the

bottle size.

•

If you are using a silicone bottle, select the milk volume setting

based on the milk volume. When the entire progress indicator is

on, wait for 3-4 minutes for the milk to warm.

•

Fill the bottle warmer with fresh room temperature water. Do not

use warm water.

17ENGLISH

Problem After switching on the bottle warmer, the entire progress indicator is

on but not ashing.

Cause

•

The bottle warmer is still too hot to warm another bottle. You may

have just nished warming a bottle. Switch o and let it cool down

for a few minutes.

Solution

•

To speed up, rell the bottle warmer with fresh cold water. When

you switch on the bottle warmer, the progress indicator lights up

gradually to indicate that the appliance is warming again.

Problem The entire progress indicator ashes when warming baby food.

Cause

•

Due to variations in baby food consistency, it is not possible for

the appliance to detect precisely how long the baby food should

be warmed.

Solution

•

Stir the baby food while the jar or container is in the bottle warmer.

For optimal result, check its temperature while it is warming .

•

When the entire progress indicator lights up continuously, the

baby food is ready for feeding.

18 ENGLISH

Warranty and support

For assistance, visit our website: www.philips.com/support or call toll free

1-800-54-Avent

Full Two-Year Warranty

Philips North America LLC warrants each new Philips product, Model SCF358

against defects in materials or workmanship for a period of two years from the date

of purchase and agrees to repair or replace any defective product without charge.

IMPORTANT: This warranty does not cover damage resulting from accident, misuse

or abuse, lack of reasonable care, the axing of any attachment not provided

with the product or loss of parts or subjecting the product to any but the specied

battery.

NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

In order to obtain warranty service, simply go to www.philips.com/support or

call toll free 1-800-54-Avent. It is suggested that for your protection you return

shipments of product by insured mail, insurance prepaid. Damage occurring during

shipment is not covered by this warranty.

NOTE: No other warranty, written or oral, is authorized by Philips North America

LLC. This warranty gives you specic legal rights, and you may also have other rights

which vary from state to state. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above exclusion and limitations

may not apply to you.

* Read enclosed instructions carefully.

Manufactured for: Philips Personal Health, A division of Philips North America LLC,

P.O. Box 10313, Stamford, CT 06904, USA.

PHILIPS and Philips Shield are registered trademarks of Koninklijke Philips N.V.

Any other servicing should be performed by an authorized service representative.

19ESPAÑOL

Contenido

PRECAUCIONES IMPORTANTES 20

Introducción 23

Instrucciones de uso 24

Limpieza y eliminación de depósitos de sarro 33

Eliminación 34

Resolución de problemas 35

Garantía y asistencia 37

20 ESPAÑOL

PRECAUCIONES

IMPORTANTES

Si utiliza un artefacto eléctrico siempre debe tomar medidas de seguridad básicas,

tales como:

Lea todas las instrucciones.

Peligro

- Para evitar una descarga eléctrica, no sumerja el cable

de alimentación, los conectores ni el artefacto en agua u

otros líquidos.

Advertencia

- Utilice el artefacto solo en interiores.

- No deje que el cable de alimentación cuelgue del borde

de la mesa o de la encimera. Guarde el cable sobrante

en la base del calentador de biberones.

- Se proporciona un cable de alimentación corto para

evitar enredarse o tropezarse con un cable más largo.

- Si utiliza un cable de extensión, este se debe colocar de

manera que no cuelgue de la encimera ni la sobremesa,

donde los niños puedan tirarlo o tropezar con él.

- La clasicación eléctrica del cable o del cable de

extensión debe ser, como mínimo, igual a la del

artefacto.

- Mantenga el cable de alimentación alejado de

supercies calientes.

- Conecte el artefacto solo en enchufes de pared con

conexión a tierra. Asegúrese siempre de que el enchufe

esté insertado correctamente en el enchufe de pared.

- Antes de conectar el artefacto, revise que el voltaje

indicado en la parte inferior corresponda con el voltaje

local.

La page charge ...

mothercare Chauffe-biberon rapide Avent Manuel utilisateur

Ce manuel convient également à

mothercare Chauffe-biberon rapide Avent Manuel utilisateur

dans d''autres langues

Autres documents