Allmand MAXI-LITE Le manuel du propriétaire

Operator’s Manual

MAXI-LITE®

Part No.: 114005

Revision: D

en

Manuel d'utilisation

MAXI-LITE®

Manual del operario

MAXI-LITE®

fr

es

www.allmand.com2

Breathing diesel engine exhaust exposes you

to chemicals known to the State of California

to cause cancer and birth defects or other

reproductive harm.

• Always start and operate the engine in a well-

ventilated area.

• If in an enclosed area, vent the exhaust to the

outside.

• Do not modify or tamper with the exhaust

system.

• Do not idle the engine except as necessary.

For more information go to

www.P65Warnings.ca.gov/diesel.

Recording the equipment information will help when placing

an order for replacement parts and/or decals.

Manual Contents:

Record Important Information

Introduction ....................................................................... 2

Products Covered by This Manual ................................... 2

Safety ................................................................................. 2

Features and Controls ...................................................... 9

Pre-Operation Checklist ................................................. 10

Transporting .................................................................... 11

Operation ......................................................................... 16

Maintenance .................................................................... 23

Specications .................................................................. 30

Troubleshooting .............................................................. 33

Reporting Safety Defects ................................................ 34

Tire Safety Information .................................................... 34

Addendum - Unit Options ............................................... 41

Company Equipment No:

Unit Model No:

Unit VIN:

Engine Model No: Serial No:

Generator Model No: Serial No:

Accessories:

WARNING

Introduction

About This Manual

TAKE TIME TO READ THIS MANUAL THOROUGHLY

This instruction manual provides necessary instructions for

the Allmand® Maxi-Lite®.

The information found in this manual is in eect at the time

of printing. Briggs & Stratton, LLC. may change contents

without notice and without incurring obligation.

The images throughout this manual are representative, and

may dier from your model.

Any reference in this manual to left or right shall be

determined by looking at the trailer from the rear.

If uncertain about any of the information in the manual,

contact the Allmand service department at

1-800-562-1373, or contact us through the Allmand website,

www.allmand.com.

Save these original instructions for future reference.

Products Covered by This

Manual

The following products are covered by this manual:

Maxi-Lite®

Safety

For your safety, the safety of others, and to protect the

performance of equipment, follow the precautions listed

throughout the manual before operation, during operation

and during periodic maintenance procedures.

Indicates a potential personal injury hazard.

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

Safety Denitions

In addition to this Operator’s Manual, be sure to read any

component manuals that are included with the machine.

For models equipped with Perkins engines, the engine

operator’s manual can be found online at https://www.

perkins.com/en_GB/aftermarket/operation-maintenance-

manuals/9064.html.

Component Manuals

en

English 3

CAUTION

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE

Information considered important but not hazard related.

The following section contains general safety precautions

and guidelines that must be obeyed to reduce risk to

personal safety. Special safety precautions are listed in

specic procedures. Read and understand all of the safety

precautions before operating or performing repairs or

maintenance.

Safety Precautions

DANGER

Electrocution Hazard

• Always check overhead wires and obstructions before

raising or lowering the light tower.

• Always obey the rules or instructions for your work

site and state, province and national electric code for

maintaining a safe distance from overhead wires.

• High voltage is present when engine is running.

Never attempt to service electrical components while

engine is running.

• Do not operate the light tower if the insulation on

the electrical cord or other electrical wiring is cut or

worn or if bare wires are exposed. Repair or replace

damaged wiring before starting the engine.

WARNING

Unsafe Operation Hazard

• Never permit anyone to install or operate the

equipment without proper training.

• Read and understand this Operator’s Manual, the

Engine Operator’s Manual, and any other component

manuals before operating or servicing the light tower

to make sure that safe operating practices and

maintenance procedures are followed.

• Safety signs and decals are additional reminders for

safe operating and maintenance techniques.

WARNING

Fall Hazard

• Never carry riders on the equipment.

WARNING

Modication Hazard

• Never modify the equipment without written consent

of the manufacturer. Any modication could aect the

safe operation of the equipment.

WARNING

Exposure Hazard

• Always wear personal protective equipment, including

appropriate clothing, gloves, work shoes, and eye

and hearing protection, as required by the task at

hand.

WARNING

Rollover Hazard

• Do not raise, lower or use light tower unless all

outriggers and jacks are positioned on rm ground.

• Never move or reposition the light tower while the

light tower is extended in the vertical position.

WARNING

Fire and Explosion Hazard

Batteries give o explosive gases during recharging.

Sparks could cause explosions, resulting in death or

serious injury.

WARNING

Burn Hazard

Batteries contain acid, which is extremely caustic.

Contact with battery contents could cause severe

chemical burns.

WARNING

Shock Hazard

Batteries present a risk of electric shock and high short

circuit current.

• Always disconnect the negative (-) battery cable

before servicing equipment.

• DO NOT dispose of battery in a re. Recycle battery.

• DO NOT allow any open ame, spark, heat, or

lit cigarette during and for several minutes after

charging a battery.

• DO NOT open or mutilate battery.

• DO NOT charge a frozen battery. Always slowly warm

the battery to room temperature before charging.

• Wear protective gloves, rubber apron, rubber boots

and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

www.allmand.com4

WARNING

Fire and Explosion Hazard

• Diesel fuel is ammable and explosive under certain

conditions.

• Never use a shop rag to catch fuel.

• Wipe up all spills immediately.

• Never refuel with the engine running.

• Store any containers containing fuel in a well

ventilated area, away from any combustibles or

sources of ignition.

WARNING

Alcohol and Drug Hazard

• Never operate the light tower while under the

inuence of alcohol or drugs, or when ill.

WARNING

Entanglement / Sever Hazard

• Always stop the engine before beginning service.

• If the engine must be serviced while it is operating,

remove all jewelry, tie back long hair and keep hands,

other body parts and clothing away from moving/

rotating parts.

• Verify that all guards and covers are attached

properly to the equipment before starting the engine.

Do not start the engine if any guards or covers are

not properly installed on the equipment.

• Attach a “Do Not Operate” tag near the key switch

while performing maintenance on the equipment.

WARNING

Flying Object Hazard

• Always wear eye protection when cleaning the

equipment with compressed air or high pressure

water. Dust, ying debris, compressed air,

pressurized water or steam may injure your eyes.

WARNING

Coolant Hazard

• Wear eye protection and rubber gloves when

handling engine coolant. If contact with the eyes or

skin should occur, ush eyes and wash immediately

with clean water.

WARNING

Burn Hazard

• Opening cap on hot radiator could result in death

or serious injury. Allow radiator to cool down before

opening cap.

WARNING

Burn Hazard

• Light xtures and some of the engine surfaces

become very hot during operation and shortly after

shutdown.

• Keep hands and other body parts away from hot

surfaces.

• Handle hot components, such as light xtures, with

heat resistant gloves.

NOTICE

• Any part which is found defective as a result of

inspection or any part whose measured value does

not satisfy the standard or limit MUST be replaced.

• Always tighten components to the specied torque.

Loose parts can cause equipment damage or cause it

to operate improperly.

• Follow the guidelines of the Environmental Protection

Agency (EPA), Environment Canada (EC) or other

governmental agencies for the proper disposal of

hazardous materials such as engine oil, diesel fuel

and engine coolant.

• Only use replacement parts specied. Other

replacement parts may eect warranty coverage.

• Clean all accumulated dirt and debris away from the

body of the equipment and its components before

you inspect the equipment or perform preventative

maintenance procedures or repairs. Operating

equipment with accumulated dirt and debris will

cause premature wear of equipment components.

• Never dispose of hazardous materials by dumping

them into a sewer, on the ground, or into groundwater

or waterways.

• Retrieve any tools or parts that may have dropped

inside of the equipment to avoid improper equipment

operation.

• If any alert indicator illuminates during equipment

operation, stop the engine immediately. Determine

the cause and repair the problem before continuing to

operate the equipment.

en

English 5

Safety Decals

Before operating your unit, read and understand the

following safety decals. The cautions, warnings, and

instructions are for your safety. To avoid personal injury or

damage to the unit, understand and obey all the decals.

Keep the decals from becoming dirty or torn, and replace

them if they are lost or damaged. Also, if a part needs to

be replaced that has a decal attached to it, make sure to

order the new part and decal at the same time.

If any safety or instructional decals become worn or

damaged, and cannot be read, order replacement decals

from your dealer.

Domestic Models

DANGER - Entering electrical

compartment while equipment is

in operation will result in death or

serious injury. Unplug equipment

before entering electrical

compartment.

Part No. 118074

118074

Machine Grounding Information /

Ground Lug

Part No. 122470

Neutral bonded to frame.

Machine to be grounded in accordance

with requirements as outlined by

local inspection authorities.

Neutre mis à al masse à la carcasse

du moteur.

L'apparel doit etre misa la terre

conformement aux exgences des

services d'inspection locaux.

122470

WARNING - Opening cap on hot

radiator could result in death or

serious injury. Allow radiator to

cool down before opening cap.

Part No. 118651

Opening cap on hot radiator

could result in death or

serious injury.

Allow radiator to cool down

before opening cap.

L’ouverture du bouchon sur

un radiateur chaud pourrait

causer la mort ou des

blessures graves.

Laisser le radiateur refroidir

avant de dévisser le

bouchon.

118651

WARNING - Contact with hot

exhaust gases and parts could

cause death or serious injury.

Avoid hot exhaust gases. Keep

hands and combustible materials

away from hot parts.

Part No. 118162

118162

WARNING - Failure to follow

warnings, instructions and

operator’s manual could result

in death or serious injury. Read

and follow operator’s manual

before operating or servicing this

equipment.

Part No. 122467-1

L’omission de respecter

les avertissements, les

instructions et le manuel

de l’utilisateur pourrait

entraîner des blessures

graves ou la mort.

Failure to follow

warnings, instructions,

and operator’s manual

could result in death or

serious injury.

Read and follow

operator’s manual

before operating or

servicing this

equipment.

Lire et suivre le manuel

d’utilisation avant de

faire fonctionner ou de

faire l’entretien de cet

équipement.

Domestic Models

WARNING - Unexpected start of

engine could result in death or

serious injury. Read and follow

electronic controller operator’s

manual before operating or

servicing this equipment.

Part No. 122467-2 Le démarrage inattendu

du moteur pourrait

provoquer la mort ou

des blessures graves.

Lire et suivre le manuel

d’utilisation du

contrôleur électronique

avant d’utiliser ou de

réparer cet équipement.

Unexpected start of

engine could result in

death or serious injury.

Read and follow

electronic controller

operator’s manual

before operating or

servicing this equipment.

WARNING - Contact with hot

exhaust gases and parts could

cause death or serious injury.

Avoid hot exhaust gases. Keep

hands and combustible materials

away from hot parts.

Part No. 122467-3

Contact with hot

exhaust gases and

parts could cause

serious injury.

Avoid hot exhaust

gases. Keep hands

and combustible

materials away from

hot parts.

Tout contact avec les

pièces et les gaz

d’échappement

chauds pourrait

causer la mort ou

des blessures

graves.

Éviter les gaz

d’échappement

chauds. Tenir les

mains et les produits

inflammables à

l’écart des pièces

chaudes.

WARNING - Contact with rotating

parts could result in death or

serious injury. Keep away from

rotating parts.

Part No. 122467-4

Contact with rotating parts

could result in death or serious

injury.

Keep away from

rotating parts.

Se tenir à l’écart

des pièces en

mouvement.

Le contact avec des pièces en

mouvement pourrait résulter en

de graves blessures voire la

mort.

WARNING - Opening cap on hot

radiator could result in death or

serious injury. Allow radiator to

cool down before opening cap.

Part No. 122467-5

Opening cap on hot

radiator could result in

death or serious injury.

Allow radiator to cool

down before opening

cap.

L’ouverture du bouchon

sur un radiateur chaud

pourrait causer la mort

ou des blessures

graves.

Laisser le radiateur

refroidir avant de

dévisser le bouchon.

WARNING - Exposure to corrosive

materials could cause result in

death or serious injury. Wear

protective gloves when handling

battery.

Part No. 122467-6

Exposure to corrosive

material could result in

death or serious injury.

Wear protective gloves

when handling battery.

Toute exposition à des

produits corrosifs

pourrait causer la mort

ou des blessures

graves.

Porter des gants de

protection en

manipulant la batterie.

WARNING - Smoking materials,

open ames, or other forms of

ignition near the battery could

cause explosion resulting in death

or serious injury. Keep smoking

materials, open ames, or other

forms of ignition away from the

battery.

Part No. 122467-7

Smoking materials, open

flames, or other forms of

ignition near the battery could

cause explosion resulting

in death or serious injury.

Les articles de fumeur, les

flammes nues ou d’autres

formes d’allumage près de

la batterie pourraient causer

une explosion, causant la

mort ou des blessures

graves.

Keep smoking materials, open

flames, and other forms of

ignition away from the battery.

Tenir les articles de fumeur, les

flammes nues ou les autres

formes d’allumage à l’écart de

la batterie.

CSA File Number

Part No. 110361

110361

CSA File Number: 204930

For electrical equipment only.

Pour matériel électrique seulement.

www.allmand.com6

Domestic Models

WARNING - Standing under

light tower mast and xtures

during lowering operation could

result in death or serious injury.

Keep bystanders away from light

tower during lowering and raising

operations.

WARNING - Handling light xtures

when they are hot could result in

death or serious injury. Keep clear

of light xtures when illuminated

or hot.

WARNING - Looking at illuminated

light xtures could result in serious

injury. Do not look directly at

illuminated light xtures.

Part No. 122478

122478

Ne jamais regarder

directement des luminaires

allumés.

AVERTISSEMENT

WARNING

Looking at illuminated

light fixtures could result

in serious injury.

Do not look directly at

illuminated light fixtures.

Regarderdes luminaires

allumés pourrait provoquer

de graves blessures.

AVERTISSEMENT

WARNING

Standing under light tower

mast and fixtures during

lowering operation could

result in death or serious

injury.

Keep bystanders away

from light tower during

lowering and raising

operations.

Le fait de se tenir debout sous

une tour d’éclairage et de ses

accessoires alors qu’elle est

abaissée pourrait causer la

mort ou des blessures graves.

Tenir les spectateurs à l’écart

de la tour d’éclairage pendant

qu’on la soulève ou l’abaisse.

AVERTISSEMENT

WARNING

La manipulation des

luminaires alors qu’ils sont

chauds pourrait causer la mort

ou des blessures graves.

Rester à l’écart des luminaires

lorsqu’ils sont allumés ou

chauds.

Handling light fixtures when

they are hot could result in

death or serious injury.

Keep clear of light

fixtures when illuminated

or hot.

WARNING - Failure to follow

warnings, instructions and

operator’s manual could result

in death or serious injury. Read

and follow operator’s manual

before operating or servicing this

equipment.

Part No. 122469-1

L’omission de respecter les

avertissements, les instructions

et le manuel de l’utilisateur

pourrait entraîner des blessures

graves ou la mort.

Failure to follow warnings,

instructions, and operator’s

manual could result in

death or serious injury.

Read and follow operator’s

manual before operating or

servicing this equipment.

Lire et suivre le manuel

d’utilisation avant de faire

fonctionner ou de faire

l’entretien de cet

équipement.

DANGER - Contacting power lines

when raising light tower will result

in death or serious injury. Keep

light tower far away from power

lines.

Part No. 122469-2

Contacting power lines

when raising light tower will

result in death or serious

injury.

Keep light tower far away

from power lines.

Le contact avec une ligne

électrique lorsque la tour

d’éclairage est levée

entraînera des blessures

graves ou la mort.

Tenir la tour d’éclairage

éloignée des lignes

électriques.

WARNING - Standing under

light tower mast and xtures

during lowering operation could

result in death or serious injury.

Keep bystanders away from light

tower during lowering and raising

operations.

Part No. 122469-3

Standing under light tower

mast and fixtures during

lowering operation could

result in death or serious

injury.

Keep bystanders away from

light tower during lowering

and raising operations.

Le fait de se tenir debout sous

une tour d’éclairage et de ses

accessoires alors qu’elle est

abaissée pourrait causer la mort

ou des blessures graves.

Tenir les spectateurs à l’écart de

la tour d’éclairage pendant qu’on

la soulève ou l’abaisse.

WARNING - Operation of this

equipment may create sparks

that can start res around dry

vegetation. A spark arrestor may

be required. The operator should

contact local re agencies for

laws or regulations relating to re

prevention requirements.

Part No. 122469-4

Le fonctionnement de cet

appareil peut provoquer des

étincelles qui peuvent enflammer

de la végétation sèche

environnante. Un pare-étincelles

peut être requis. L’opérateur doit

communiquer avec le service

d’incendie local pour connaître

les lois ou les règlements

régissant la prévention des

incendies.

Operation of this equipment may

create sparks that can start fires

around dry vegetation. A spark

arrestor may be required. The

operator should contact local fire

agencies for laws or regulations

relating to fire prevention

requirements.

WARNING - Raising light tower

without positioning outriggers

and lowering jacks could cause

machine rollover resulting in

death or serious injury. Position

outriggers and lower jacks on a

stable surface before raising light

tower.

Part No. 122469-5

Raising light tower prior to

positioning outriggers and

lowering jacks could cause

machine rollover resulting in

death or serious injury.

Position outriggers and lower

jacks on a stable surface

before raising light tower.

Le fait de soulever la tour d’éclairage

avant de positionner correctement les

longerons et sans baisser les vérins

pourrait entraîner le basculement de

la machine et provoquer des

blessures graves ou la mort.

Il faut positionner les longerons et

abaisser les vérins sur une surface

stable avant de lever la tour

d’éclairage.

WARNING - Engine exhaust

contains carbon monoxide, a

poisonous gas that could cause

death or serious injury. Run

equipment far from windows,

doors and vents. Do not run

equipment indoors or in partially

enclosed spaces.

Part No. 122469-6

Engine exhaust contains

carbon monoxide, a

poisonous gas that could

cause death or serious

injury.

Le moteur contient du

monoxyde de carbone, un

gaz toxique pouvant

provoquer la mort ou de

graves blessures.

Run equipment far from

windows, doors and vents.

Do not run equipment

indoors or in partially

enclosed spaces.

Faites tourner à l’extérieur,

loin des fenêtres, des

portes et des évents. Ne

faites pas fonctionner à

l’intérieur ni dans un

espace partiellement fermé.

Domestic Models

WARNING - Breathing diesel

engine exhaust exposes you to

chemicals known to the State of

California to cause cancer and

birth defects or other reproductive

harm.

• Always start and operate the

engine in a well-ventilated

area.

• If in an enclosed area, vent

the exhaust to the outside.

• Do not modify or tamper with

the exhaust system.

• Do not idle the engine except

as necessary.

www.P65warnings.ca.gov/diesel

Part No. 122469-7

www.P65warnings.ca.gov/diesel

• Always start and operate the engine in a

well-ventilated area.

• If in an enclosed area, vent the exhaust to

the outside.

• Do not modify or tamper with the exhaust

system.

• Do not idle the engine except as necessary.

www.P65Warnings.ca.gov/diesel.

• Toujours démarrer et faire fonctionner le

moteur dans un endroit bien ventilé.

• Si le moteur est utilisé dans un espace fermé,

ventiler les gaz d’échappement à l’extérieur.

• Ne pas modifier ni altérer le système

d’échappement.

• Ne pas mettre le moteur au ralenti sauf en cas

de nécessité.

Breathing diesel engine

exhaust exposes you to

chemicals known to the State

of California to cause cancer

and birth defects or other

reproductive harm.

L’inspiration de gaz d’échappement

du moteur vous exposeà des produits

chimiques connus selon l’État de

Californie pour causer le cancer, des

anomalies congénitales ou d’autres

effets nuisibles à la reproduction.

WARNING - Failure to follow

warnings, instructions and

operator’s manual could result

in death or serious injury. Read

and follow operator’s manual

before operating or servicing this

equipment.

WARNING - Failure to lower tower

into a secured position before

towing could result in death or

serious injury. Lower tower to a

secured position before towing.

WARNING - Excessive towing

speed could result in death or

serious injury. Do not exceed

65mph (105km/h) when towing

trailer.

Part No. 122463

Failure to lower tower into a secured

position before towing could result in

death or serious injury.

Lower tower to a secured position

before towing.

Ne pas abaisser la tour d’éclairage en

position sécurisée au préalable peut

provoquer la mort ou des blessures

graves.

Abaisser la tour en position

sécurisée avant le remorquage.

Excessive towing speed could result

in death or serious injury.

Do not exceed 65mph (105km/h)

when towing trailer.

Une vitesse de remorquage excessive

pourrait entraîner la mort ou de

graves blessures.

Ne pas dépasser 105 km/h (65 mi/h)

lors du remorquage.

Read and follow operator’s manual

before operating or servicing this

equipment.

L’omission de respecter les

avertissements, les instructions et le

manuel de l’utilisateur pourrait entraîner

des blessures graves ou la mort.

Lire et suivre le manuel d’utilisation

avant de faire fonctionner ou de faire

l’entretien de cet équipement.

Failure to follow warnings, instructions,

and operator’s manual could result in

death or serious injury.

122463

International Models

DANGER - Entering electrical

compartment while equipment is

in operation will result in death or

serious injury. Unplug equipment

before entering electrical

compartment.

Part No. 104880

104880

DANGER - Entering electrical

compartment while equipment is

in operation will result in death or

serious injury. Unplug equipment

before entering electrical

compartment.

Part No. 109012

109012

WARNING - Opening cap on hot

radiator could result in death or

serious injury. Allow radiator to

cool down before opening cap.

Part No. 122091

122091

en

English 7

International Models

WARNING - Engine exhaust

contains carbon monoxide, a

poisonous gas that could cause

death or serious injury. Run

equipment far from windows,

doors and vents. Do not run

equipment indoors or in partially

enclosed spaces.

Part No. 113941

113941

WARNING - Contact with hot

exhaust gases and parts could

cause death or serious injury.

Avoid hot exhaust gases. Keep

hands and combustible materials

away from hot parts.

Part No. 107529

107529

WARNING - Standing under light

tower mast and xtures during

lowering operation could result in

death or serious injury.

Keep bystanders away from light

tower during lowering and raising

operations.

WARNING - Handling light xtures

when they are hot could result in

death or serious injury. Keep clear

of light xtures when illuminated

or hot.

WARNING - Looking at illuminated

light xtures could result in serious

injury. Do not look directly at

illuminated light xtures.

Part No. 118444

118444

WARNING - Contact with rotating

parts could result in death or

serious injury. Keep away from

rotating parts.

WARNING - Opening cap on hot

radiator could result in death or

serious injury. Allow radiator to

cool down before opening cap.

WARNING - Smoking materials,

open ames, or other forms of

ignition near the battery could

cause explosion resulting in death

or serious injury. Keep smoking

materials, open ames, or other

forms of ignition away from the

battery.

WARNING - Exposure to corrosive

materials could cause result in

death or serious injury. Wear

protective gloves when handling

battery.

Part No. 110310

110310

Ground Lug

Part No. 107969

107969

International Models

WARNING - Excessive towing

speed could result in death or

serious injury. Do not exceed

65mph (105km/h) when towing

trailer.

WARNING - Failure to secure light

bar and lower tower could cause

light xtures to detach resulting

in death or serious injury. Lock

light tower to lowest position and

secure light bar before towing.

Part No. 107458

107458

DANGER - Contacting power lines

when raising light tower will result

in death or serious injury. Keep

light tower far away from power

lines.

WARNING - Raising light tower

without positioning outriggers

and lowering jacks could cause

machine rollover resulting in

death or serious injury. Position

outriggers and lower jacks on a

stable surface before raising light

tower.

WARNING - Failure to follow

warnings, instructions, and

operator’s manual could result

in death or serious injury.

Open right side door to locate

operator’s manual. Read and

follow operator’s manual before

operating or servicing this

equipment.

Part No. 112163

0° ± 2.8° 85km/h (53mph) max

112163

WARNING - Automatic Engine

Start. Unexpected start of engine

could result in death or serious

injury. Read and follow electronic

controller operator’s manual

before operating or servicing this

equipment.

Part No. 107978 (LSC and Deep

Sea Models)

107978

All Models

Tire Information

Part No. 113943 TIRE INFORMATION

SEE OWNER’S

MANUAL FOR

ADDITIONAL

INFORMATION

The weight of cargo should never exceed 0 kg or 0 lbs.

TIRE

FRONT

REAR

SPARE

SIZE

ST 225/75R15D

NONE

448kPa, 65PSI

COLD TIRE PRESSURE

113943

Emergency Stop

Part No. 105567

105567

www.allmand.com8

All Models

Operating Instructions

Part No. 122477

1

2

±2.8°

1

2

3

1B

3

2A 3A 4A

1 2 3 4 5 6

1

2B 3B

1

1A

2B1B

2

1B

3

2

1

122477

1A

Electrical Info

Part No. 112133 60 Hz

120/208 V

56 A

112133

20 kW

3 Ø

Electrical Info

Part No. 112132 60 Hz

120/240 V

167/83 A

112132

20 kW

1 Ø

Electrical Info

Part No. 112130 60 Hz

120/240 V

125/63 A

112130

15 kW

1 Ø

Electrical Info

Part No. 112127 60 Hz

120/240 V

67/33 A

112127

8 kW

1 Ø

Tie-Down Point

Part No. 109005

109005

Forklift Pocket

Part No. 107254

107254

Oil Drain

Part No. 107973

107973

Fluid Containment Drain

Part No. 107971

107971

All Models

Coolant Drain

Part No. 104752

104752

Lift Weight

Part No. 122480

122480

Trailer Serial Number (VIN)

Part No. 133592

Product Operations QR Code

Part No. 123247

123247

Operation Icons

The following table contains operation icons that may be

found on the unit, along with the meaning of each icon.

Icon Meaning Icon Meaning

Power On Light Tower

Raise

Power O Light Tower

Lower

Engine Stop Engine Oil Drain

Engine Run Coolant Drain

Engine Start Fluid

Containment

Drain

Engine Preheat Circuit Breaker

Hourmeter Disconnecting

Circuit Breaker

en

English 9

Icon Meaning Icon Meaning

Electronic

Controller

Earth Ground

Work Light

Features and Controls

The Allmand® Maxi-Lite® Light Tower is intended for use

as a stationary lighting device to illuminate large areas.

Identify the features and controls of the machine by

comparing Figures 1 through 3 with the tables following.

See Transporting and Operation for detailed information

on each feature / control.

1

F

H

E

C

D

B

A

I

G

L

J

K

M

N

O

Ref Description

A Safety Chains (2)

B Trailer Coupler / Lunette Ring

C Tongue Jack

DHydraulic Light Tower

E Light Assembly (4 or 6, depending on model)

F Light Bar

G Lifting Eye

H Engine Compartment Access Door

I Ground Lug

J Rear Outrigger & Stabilizer Jack (each side)

K Rear Forklift Pocket / Tie Down Point (each side)

Ref Description

L Front Forklift Pocket (each side)

M Front Outrigger & Stabilizer Jack (each side)

N Step Plate

O Front Tie Down Loop

2

A

E

J

G

F

I

B

H

CD

Ref Description

A Engine Compartment Access Door

B Breakaway Kit

C License Bracket / Marker Light

D Engine Oil Drain

E Fluid Containment Drain

F Engine Coolant Drain

G Tail Light (2)

H Control Panel Access Door

I Low Fuel Strobe Light (Select models only)

JRadiator Access Door

www.allmand.com10

3

A

B

C

Ref Description

A Engine Panel

B Light Panel

C Auxiliary Outlet Panel

Pre-Operation Checklist

Perform the following checks before transporting and

operating the unit, when performing general maintenance,

and after the light tower has been stored or idle for a

period of time.

WARNING

Unsafe Operation Hazard

Operating or transporting the machine with worn,

damaged or missing parts can result in death or serious

injury. Always replace worn, damaged or missing parts

promptly. Do not transport or operate the machine until all

worn, damaged or missing parts have been replaced, and

proper operation of the machine has been veried.

NOTICE

We encourage the use of authorized replacement

Allmand parts. The warranty does not cover damage or

performance problems caused by the use of parts that

are not authorized replacement parts.

1. Check that all safety and operation decals are

present and legible. See Safety - Safety Decals.

2. Check that all operator’s manuals (product, engine,

generator, etc.) are with the unit.

3. Check the following components for wear and

damage, and for proper operation:

A. Tongue jack

• Check for rust or damage. Repair or

replace as needed.

• Check for proper operation. See

Transporting - Using The Tongue Jack.

B. Hitch Assembly (trailer coupler / lunette ring)

• Check for rust or damage. Repair or

replace as needed.

• Check for proper operation. See

Transporting - Coupling And

Uncoupling The Trailer Hitch.

• Check hardware for proper tightness.

Tighten as needed.

C. Safety chains

• Check for rust or damage. Repair or

replace as needed.

• Check hardware for proper tightness.

Tighten as needed.

D. Trailer lighting cable

• Check for cut, frayed or bare wires.

Repair or replace as needed.

• Check connector for damage. Repair or

replace as needed.

E. Breakaway kit

• Check for broken or frayed wires or

breakaway cable.

• Check battery charge status.

F. Tires

• Check for wear, cuts, cracks, etc.

Replace as needed.

• Check and adjust ination pressure.

See Specications for proper ination

pressure.

G. Brakes

• Check brakes for proper operation and

wear. Repair as needed.

H. Axle and undercarriage

• Check for rust or damage. Repair as

needed.

I. Outriggers and stabilizer jacks

• Check for rust or damage. Repair or

replace as needed.

• Check for proper operation. See

Operation - Using The Outriggers &

Stabilizer Jacks.

J. Electrical wiring

• Check for cut, worn or bare electrical

wiring. Repair as needed.

en

English 11

WARNING

Electrocution Hazard

Operating the unit with cut, worn or bare electrical

wiring could result in death or serious injury. Repair

or replace damaged wiring before operating the

light tower.

K. Engine

• Check for leaks or other signs of wear or

damage. Repair as needed.

• Check the air cleaner to be sure it is

rmly attached, and that the air cleaner

seals and hose clamps are properly

secured. Check the air cleaner element.

Replace if necessary.

L. Light tower

• Check for worn or frayed cables,

hydraulic leaks, etc. Repair as needed.

• Check and adjust the hydraulic uid level

(hydraulic (vertical) tower models only).

See Maintenance - Hydraulic Pump.

M. Tower lights

• Check for broken lenses, bulbs, etc.

Repair or replace as needed.

4. Check and adjust uid levels.

A. Engine oil

• Refer to the engine operator’s manual

for oil recommendations, capacity, and

procedures.

NOTICE

Operating engine without oil will cause engine

damage.

B. Engine coolant

• Refer to the engine operator’s manual for

coolant recommendations, capacity, and

procedures.

NOTICE

Operating engine without coolant will cause engine

damage.

C. Fuel

• See Operation - Fueling The Unit for

fuel tank location, capacity, and fueling

procedures.

Transporting

WARNING

Unsafe Operation Hazard

Operating the equipment without proper training could

result in death or serious injury. Never allow anyone to

operate the equipment without proper training.

Before transporting, read Safety.

Preparing For Work Site Delivery

Prepare the unit for delivery to the work site, especially if

it has been stored or idle for a period of time.

WARNING

Unsafe Operation Hazard

Operating or transporting a machine with worn, damaged

or missing parts can result in death or serious injury.

Always replace worn, damaged or missing parts promptly.

Do not operate or transport this machine until all worn,

damaged or missing parts have been replaced, and

proper operation of the machine has been veried.

1. Perform all pre-operation checks. See Pre-Operation

Checklist.

2. Run the engine through a startup and shutdown cycle

to verify operation. See Operation - Operating The

Engine. Also refer to the engine operator’s manual.

3. Raise and lower the light tower to verify operation.

See Operation - Raising And Lowering The Light

Tower.

4. Turn the tower lights on and o to verify operation.

See Operation - Operating The Tower Lights.

Preparing For Transport

1. Shut down the tower lights. See Operation -

Operating The Tower Lights.

2. Shut down the engine. See Operation - Operating

The Engine. Also refer to the engine operator’s

manual

3. Lower the light tower and adjust the tower lights into

the transport position. See Operation - Raising

And Lowering The Light Tower and Operation -

Adjusting The Tower Lights.

WARNING

Tip Hazard

Failure to lower the light tower into the transport position

before transporting could result in death or serious injury.

Always lower the light tower into the transport position

before transporting.

WARNING

Burn Hazard

Handling the tower lights while hot could result in serious

injury. Allow lights to cool before handling or use heat-

resistant gloves.

4. Retract the outriggers and stabilizer jacks. See

Operation - Using The Outriggers & Stabilizer

Jacks.

5. Close and lock all access doors.

www.allmand.com12

Towing

Maximum highway speed is 65 mph (105 km/h).

Maximum o- highway speed is 20 mph (32 km/h). Do not

exceed these speed limits.

WARNING

Unsafe Operation Hazard

Towing the light tower trailer at highway speeds in excess

of 65 mph (105 km/h) could result in death or serious

injury. Do not tow the light tower trailer at highway speeds

in excess of 65 mph (105 km/h).

Tow vehicle / hitch requirements

1. Check the Gross Vehicle Weight Rating (GVWR) of

the light tower trailer. See Specications.

2. Check the rated towing capacity of the tow vehicle

and hitch. Both must meet or exceed the GVWR of

the light tower trailer.

Note: Check the vehicle owner’s manual and hitch

owner’s manual for rated towing capacities.

WARNING

Towing Hazard

Using a tow vehicle or hitch with a rated towing capacity

less than the GVWR of the light tower trailer could result

in death or serious injury. Use only a tow vehicle and

hitch with a rated towing capacity that meets or exceeds

the GVWR of the light tower trailer.

Check the tow vehicle hitch type

The light tower trailer is designed for the following types

of tow vehicle hitches:

• 2” ball hitch

• Pintle hitch

• 2-5/16” ball hitch

• 2” Bulldog hitch

Be sure the tow vehicle is equipped with either of these

hitch types. Install if needed.

WARNING

Unsafe Operation Hazard

Failure to use a tow vehicle hitch that mates with the

trailer hitch assembly could result in death or serious

injury. Use only a tow vehicle hitch that mates with the

trailer hitch assembly.

Reversing the trailer hitch assembly

The trailer hitch assembly is reversible. Use the trailer

coupler (A, Figure 4) for ball hitches, or the lunette

ring (B) for pintle hitches. To reverse the trailer hitch

assembly:

1. Remove the mounting hardware (C, Figure 4).

2. Reverse the trailer hitch assembly.

Note: Use the set of mounting holes in the trailer

tongue that will keep the trailer as level as possible

when connected to the tow vehicle.

3. Reinstall the hardware. Tighten securely.

WARNING

Unsafe Operation Hazard

Failure to properly install the trailer hitch assembly could

result in death or serious injury. Install the trailer hitch

assembly properly, and tighten the hardware securely.

4

B

A

C

Connect the light tower trailer to the tow

vehicle

1. Position a wheel chock (not supplied) rmly against

the front and rear of the wheel (A, Figure 5) on each

side of the light tower trailer.

5

A

2. Use the tongue jack to raise the trailer tongue. See

Transporting - Using The Tongue Jack.

3. Position the tow vehicle hitch under the trailer hitch.

4. Couple the trailer hitch to the tow vehicle hitch. See

Transporting - Coupling And Uncoupling The

Trailer Hitch.

en

English 13

5. Connect the safety chains.

A. Connect the safety chains (A, Figure 6) to the

safety chain pockets on the tow vehicle. Criss-

cross the chains under the hitch to cradle the

hitch in the event of a disconnect.

B. Rig the chains as tightly as possible while

allowing enough slack to permit free turning.

WARNING

Unsafe Operation Hazard

Failure to properly install safety chains could result

in death or serious injury. Always properly install

safety chains.

6. Connect the trailer lighting cable.

A. Make sure the trailer lighting cable mates with

the tow vehicle lighting cable. If needed, install

the proper cable and/or connector to the tow

vehicle.

B. Connect the trailer lighting cable to the tow

vehicle lighting cable (B, Figure 6).

C. Make sure there is adequate slack to allow for

turning without allowing the cable to drag on

the ground.

D. Check the trailer lights for proper operation.

WARNING

Unsafe Operation Hazard

Failure of trailer lights to operate properly could

result in death or serious injury. Always check for

proper operation of trailer lights, and repair or re-

place as needed.

6

A

B

7. Retract the tongue jack. See Transporting - Using

The Tongue Jack.

8. Remove the wheel chocks.

9. The trailer is now ready for towing.

To disconnect the trailer from the tow

vehicle

1. Chock the wheels.

2. Deploy the tongue jack. See Transporting - Using

The Tongue Jack.

3. Disconnect the trailer lighting cable from the tow

vehicle lighting cable.

4. Remove the safety chains from the safety chain

pockets on the tow vehicle.

5. Uncouple the trailer hitch from the tow vehicle hitch.

See Transporting - Coupling And Uncoupling The

Trailer Hitch.

6. Move the tow vehicle away from the unit.

Using The Tongue Jack

The unit is equipped with a tongue jack to raise and lower

the trailer tongue, and to level the trailer front-to-rear.

To deploy the tongue jack

1. Remove the jack locking pin (A, Figure 7).

2. Rotate the tongue jack 90° into the operating position

(B, Figure 7). Install the jack locking pin (C).

3. Unfold the jack handle into the operating position (D,

Figure 7).

WARNING

Unsafe Operation Hazard

Failure to install the jack locking pin could result in death

or serious injury. Be sure the tongue jack is locked in the

operating position with the jack locking pin.

To lower the jack foot (raise the trailer tongue)

• Turn the jack handle counterclockwise (E, Figure 7)

to lower the jack foot (F) and raise the trailer tongue.

To raise the jack foot (lower the trailer tongue)

• Turn the jack handle clockwise (G, Figure 7) to raise

the jack foot (H) and lower the trailer tongue.

To retract the tongue jack

WARNING

Unsafe Operation Hazard

Failure to support the trailer tongue before retracting the

tongue jack could result in death or serious injury. Be sure

the trailer tongue is securely supported before retracting

the tongue jack.

1. Be sure the trailer is securely supported by the tow

vehicle or other approved means.

2. Fully raise the jack foot.

www.allmand.com14

3. Fold the jack handle into the transport position (I,

Figure 7).

4. Remove the jack locking pin.

5. Rotate the tongue jack 90° into the transport position

(J, Figure 7). Install the jack locking pin.

7

D

F

B

A

EG

J

H

C

I

Using the Trailer Coupler / Lunette

Eye

Trailer Coupler

To connect the trailer to the tow vehicle

1. Lift up and pull back on the locking latch (A, Figure 8)

of the trailer coupler.

2. Lower the trailer coupler onto the vehicle ball hitch.

Make sure that the hitch ball (B, Figure 8) is fully

engaged in the coupler socket (C, Figure 8).

3. Push the locking latch forward and down. (It is self-

locking.) Install a padlock through the latch hole (D,

Figure 8) for added security.

4. Make sure that the coupler is fully installed on the ball

hitch.

To disconnect the trailer from the tow vehicle

1. Remove the padlock (if installed) from the trailer

coupler latch (D, Figure 8).

2. Lift the trailer coupler (A, Figure 8) latch up and back.

8

A

D

C

B

Lunette Eye

To connect the trailer to the tow vehicle

1. Remove the locking pin (A, Figure 9, if equipped)

from the pintle hitch (B, Figure 9).

2. Pull up on the latch (C, Figure 9), to open the pintle

hitch.

3. Lower the lunette eye (D, Figure 9) into the pintle

hook (E, Figure 9).

4. Close the pintle hitch. Make sure that the latch locks

the pintle hitch in place.

5. Install the locking pin (if equipped).

To disconnect the trailer from the tow vehicle

1. Remove the locking pin (if equipped) from the pintle

hitch.

2. Pull up on the latch to open the pintle hitch.

3. Remove the lunette eye from the pintle hook.

en

English 15

9

C

D

A

B

E

Lifting

Lifting equipment requirements

• Use only approved lifting equipment with a rated

lifting capacity that exceeds the GVWR of the unit.

See Specications.

WARNING

Unsafe Operation Hazard

Failure to use approved lifting equipment with a rated

lifting capacity that exceeds the GVWR of the unit could

result in death or serious injury. Use only approved lifting

equipment with a rated lifting capacity that exceeds the

GVWR of the unit.

Before lifting

• Be sure the light tower is fully lowered and locked in

the transport position. See Operation - Raising And

Lowering The Light Tower.

WARNING

Rollover Hazard

Failure to lower the light tower before lifting the unit could

result in death or serious injury. Always lower the light

tower before lifting the unit.

Lifting points

• Lifting eye - (A, Figure 10) Use only shackles or a

locking type hook when using the lifting eye.

• Forklift pockets - (B, Figure 10) Use forklift blades at

least 60” (152 cm) long when lifting the unit. Insert the

forklift blades fully into the forklift pockets.

WARNING

Unsafe Operation Hazard

Failure to use the designated lifting points to lift the

unit could result in death or serious injury. Use only the

designated lifting points to lift the unit.

WARNING

Unsafe Operation Hazard

Failure to properly lower and lock the tower could result in

death or serious injury. Always be sure to properly lower

and lock the tower before attempting to lift the unit.

WARNING

Crush Hazard

Standing under or near the unit while it is being lifted

could result in death or serious injury. Never stand under

or near the unit while it is being lifted.

10

A

B

Transporting on a Trailer

Three tie-down points, located on the bottom rear of the

trailer (forklift pockets on right and left sides) and the

underside of the trailer tongue (A, Figure 11), are used to

secure the unit to a transport trailer.

Note: All models have similar tie-down point locations.

WARNING

Unsafe Operation Hazard

Failure to use the designated tie-down points to secure

the unit to the transport trailer could result in death or

serious injury. Always use the designated tie-down points

to secure the unit to the transport trailer.

www.allmand.com16

1. Secure the unit at the tie-down points with

appropriately rated chains or straps.

WARNING

Unsafe Operation Hazard

Failure to use appropriately rated chains or straps to

secure the unit to the transport trailer could result in death

or serious injury. Always use appropriately rated chains or

straps to secure the unit to the transport trailer.

2. Do not apply more than 600 lbs (272 kg) force on the

chains or straps.

3. The truck operator is responsible for securing the

load properly to the transport trailer.

11

AA

Operation

Before operating, read Safety.

Choosing the Work Site

Obey state, province and federal rules and regulations, as

well as rules or instructions for the work site.

Consider the following when choosing a work site:

1. Ground surface

• Set up on smooth, at, solid ground surfaces

only.

• Do not set up on inclines of more than 2.8° (5%

grade) front-to-back and side-to-side.

WARNING

Rollover Hazard

Setting up the unit on soft or unstable ground, or on

inclines of more than 2.8° (5% grade), could result in

death or serious injury. Set up the unit only on smooth,

at solid ground surfaces with inclines of no more than

2.8° (5% grade).

2. Overhead obstructions

• Consider the height of the light tower when fully

raised. See Specications.

• Avoid areas with trees and power lines

• Other overhead obstructions

DANGER

Electrocution Hazard

Raising the light tower in the presence of electrical power

lines will result in death or serious injury. Always check for

overhead wires and obstructions before raising the light

tower.

3. Wind

• The unit is designed to operate in winds up

to 55 mph (88 km/h). Do not operate in winds

exceeding 55 mph (88 km/h).

WARNING

Rollover Hazard

Operating in winds over 55 mph (88 km/h) could result in

death or serious injury. Never operate in winds exceeding

55 mph (88 km/h).

Setting Up the Unit

1. Position the unit at the work site. See Operation -

Choosing The Work Site.

2. Chock the wheels. See Transporting – Towing.

3. If the unit was towed to the work site, disconnect from

the tow vehicle. See Transporting – Towing.

4. Level the trailer using the tongue jack. See

Transporting – Using The Tongue Jack.

5. Deploy the outriggers and stabilizer jacks. See

Operation - Using The Outriggers & Stabilizer

Jacks.

6. Adjust the tower lights. See Operation – Adjusting

The Tower Lights.

7. Raise the light tower. See Operation – Raising And

Lowering The Light Tower.

8. The unit is now set up and ready for operation.

en

English 17

Using the Outriggers and Stabilizer

Jacks

WARNING

Rollover Hazard

Failure to deploy the outriggers and stabilizer jacks

could result in death or serious injury. Always deploy the

outriggers and stabilizer jacks before raising the light

tower.

To deploy

1. Raise the outrigger locking pin (A, Figure 12).

2. Fully extend the outrigger (B, Figure 12) until the

locking pin engages the outrigger in the operating

position.

WARNING

Rollover Hazard

Failure to lock the outrigger in the operating position

could result in death or serious injury. Be sure the

outrigger is locked in the operating position.

3. Remove the stabilizer jack locking pin (C, Figure 12).

4. Rotate the stabilizer jack (D, Figure 12) 90° into

the operating position, and install the stabilizer jack

locking pin. Make sure the pin is inserted fully through

the stabilizer jack.

WARNING

Rollover Hazard

Failure to lock the stabilizer jack in the operating position

with the stabilizer jack locking pin could result in death or

serious injury. Be sure the stabilizer jack is locked in the

operating position with the stabilizer jack locking pin.

5. Unfold the jack handle (E, Figure 12) to the operating

position.

6. Turn the jack handle counterclockwise (F, Figure 12)

until the jack foot (G) is rmly planted on the work site

surface.

7. Repeat for the remaining outriggers and stabilizer

jacks.

8. Once all outriggers and stabilizer jacks are deployed,

use the stabilizer jacks to help level the unit on the

work site ground.

To retract

1. Turn the jack handle clockwise to fully raise the jack

foot.

2. Fold the jack handle to the transport position.

3. Remove the stabilizer jack locking pin.

4. Rotate the jack 90° to the transport position, and

install the stabilizer jack locking pin. Make sure the

pin is inserted fully through the stabilizer jack.

5. Raise the outrigger locking pin.

6. Retract the outrigger into the transport position. Be

sure the locking pin engages.

WARNING

Unsafe Operation Hazard

Failure to lock the outrigger in the transport position could

result in death or serious injury. Be sure the outrigger is

locked in the transport position.

7. Repeat for the remaining outriggers and stabilizer

jacks.

12

A

C

B

F

D

G

E

Adjusting The Tower Lights

WARNING

Burn Hazard

Adjusting the tower lights while the lights are hot could

result in serious injury. Allow lights to cool before

handling, or use heat-resistant gloves.

Note: The tower lights must be adjusted to the preferred

work angle before raising the light tower.

www.allmand.com18

To adjust for operation

1. Set the light bar to the preferred work angle.

A. Pull the park pin (A, Figure 13 or 14) and rotate

90° to unlock the light bar.

B. Rotate the light bar to the preferred work angle.

C. Pull the park pin and rotate back 90° to lock the

light bar in place.

2. Set the tower arms to the preferred work angle.

A. Loosen the adjustment nut (B, Figure 13 or 14)

on each tower arm.

B. Pull the park pin (C, Figure 13 or 14) and rotate

90° to unlock each tower arm.

C. Rotate each tower arm to the preferred work

angle.

D. Lock each tower arm with the park pin.

E. Tighten the adjustment nuts.

3. Set each individual light xture to the preferred work

angle.

LED

• Yoke center pivot (D, Figure 13) - adjusts the

horizontal angle of each individual light xture. Grasp

the sides of the yoke to adjust.

• Fixture pivots - adjust the vertical angle of each

individual light xture. Loosen the locking clasp

(E, Figure 13), move the light xture up or down to

adjust, then tighten the locking clasp.

Note: Four-light model shown. Six-light model similar.

13

A

B

C

D

E

Metal Halide

• Yoke center pivot (D, Figure 14) - adjusts the

horizontal angle of each individual light xture. Grasp

the sides of the yoke to adjust.

• Fixture pivots (E, Figure 14) - adjust the vertical angle

of each individual light xture. Move the light xture

up or down to adjust.

Note: Four-light model shown. Six-light model similar.

14

A

B

D

C

E

To adjust for towing

1. Set the light bar to the towing position.

A. Pull the park pin and rotate 90° to unlock the

light bar.

B. Rotate the light bar as shown in Figure 15.

C. Pull the park pin and rotate 90° to lock the light

bar.

2. Set the tower arms to the transport position.

A. Loosen the adjustment nut on each tower arm.

B. Pull and rotate the park pin to unlock each

tower arm.

C. Rotate each tower arm to set the light xture

yokes as shown in Figure 15.

D. Pull and rotate the park pin to lock each tower

arm.

E. Tighten the adjustment nuts.

3. Rotate the xture yokes and adjust the light xtures

so that the light xtures face inward toward center.

See Figure 15. On LED models, lock the light xtures

with the locking clasp.

Note: Six-light LED model shown. All other models

similar.

15

en

English 19

To adjust for transporting on a trailer /

storage

1. Set the light bar to the transport position.

A. Pull the park pin and rotate 90° to unlock the

light bar.

B. Rotate the light bar as shown in Figure 16.

C. Pull the park pin and rotate 90° to lock the light

bar.

2. Set the tower arms to the transport position.

A. Loosen the adjustment nut on each tower arm.

B. Pull and rotate the park pin to unlock each

tower arm.

C. Rotate each tower arm to set the light xture

yokes as shown in Figure 16.

D. Pull and rotate the park pin to lock each tower

arm.

E. Tighten the adjustment nuts.

3. Rotate the xture yokes and adjust the light xtures

so that the light xtures face downward. See Figure

16. On LED models, lock the light xtures with the

locking clasp.

Note: Six-light metal halide model shown. All other

models similar.

16

Raising And Lowering The Light Tower

WARNING

Crush Hazard

Raising or lowering the light tower with obstructions

or people near the light tower could result in death or

serious injury. Be sure the area is clear of people and

obstructions before raising or lowering the light tower.

Note: The engine does not need to be running to raise or

lower the light tower.

To raise the light tower

1. Move the tower switch (A, Figure 17) on the control

panel to the UP position to raise the tower to the

preferred height.

To lower the light tower

1. Turn the tower lights o before lowering the light

tower. See Operation - Operating The Tower

Lights.

2. Move the tower switch (A, Figure 17) on the control

panel to the DOWN position until the tower is fully

lowered.

3. Hold the tower switch in the DOWN position for three

additional seconds, to make sure the tower is fully

lowered.

17

A

Fueling The Unit

Two fuel tanks are located inside the engine

compartment, one on each side of the unit, each with a

ller cap.

To fuel

1. Open the engine compartment access doors to

access the fuel tanks.

2. Open the ller cap(s).

3. Add fuel as needed. Refer to the engine

operator’s manual for fuel recommendations. See

Specications for fuel capacity.

NOTICE

Using engine fuels other that those recommended by the

engine manufacturer could cause damage to your engine

or its emission control system resulting in voiding the

engine manufacturer’s warranty. Always read and follow

the engine manufacturer’s fuel recommendations.

NOTICE

Pressurized fueling is not allowed.

www.allmand.com20

Operating The Unit

Before Operating

1. Perform pre-operation checks. See Pre-Operation

Checklist.

2. Make sure the unit is set up properly at the work site.

See Operation - Setting Up The Unit.

Operating The Engine

Key-Start Models

To start the engine

1. Turn the key switch (D, Figure 18) to PREHEAT. Hold

for 10 seconds.

2. Turn the key switch past RUN to START.

3. Once the engine starts, release the key switch; it will

automatically return to RUN.

Note: The hourmeter (C, Figure 18) indicates the total

hours of engine operation.

NOTICE

Do not operate the starter for longer than 10 seconds.

Wait 30 seconds between starting attempts. Failure to do

so could result in starter damage.

18

B

CD

A

Ref Description

A Interior Light - Turns on lights inside engine compartment

B Tower Lift Switch - see Operation - Raising And Lowering The

Light Tower

C Hourmeter

D Key Switch

To shut down the engine

1. Turn the key switch to OFF.

LSC Models

To start the engine

1. Switch the LSC On / O switch (C, Figure 19) to the

‘On’ position.

2. To manually start the engine *:

• Press the button below the ‘Start’ indicator on the

high resolution LCD panel (D, Figure 19). This

indicator will immediately change to ‘Stop’.

• An alarm will sound for about 5 seconds to warn

that the engine is about to start.

• The glow plug indicator will be visible on the LCD

to indicate that the glow plug is on.

• After the glow plug has warmed the intake, the

engine will begin to crank.

• If the engine does not start, the LSC will attempt

the start the engine twice more. If the engine

does not start after three trys, a “failed start” error

code will appear.

3. After the engine has started, the lights will turn

on automatically after about 20 seconds. All light

circuit breakers need to be in the ‘On’ position. With

the LSC switch in the ‘On’ position, and prior to

starting the engine, the ‘Low Oil Pressure” warning

will appear. This is normal. The ‘Low Oil Pressure”

warning should go out within 5 seconds of engine

start up. If the Automatic Engine Shutdown System

detects low oil pressure after the engine has

started and stabilized, it will shut down the engine

automatically.

Note: The fuel symbol on the LCD panel will begin

to ash red when low fuel level is detected. The

machine is factory set for a low fuel level of ½ full.

This can be re-set by the user. See separate LSC

Display Module Instruction Manual for re-setting

instructions.

WARNING

Automatic Engine Start Hazard

Unexpected start of engine could result in death or

serious injury. Read and follow electronic controller

operator’s manual before operating or servicing this

equipment.

19

B

C

D

A

Ref Description

A Interior Light - Turns on lights inside engine compartment

B Tower Lift Switch - see Operation - Raising And Lowering The

Light Tower

C LSC Mode Switch

D LSC Unit

La page charge ...

Allmand MAXI-LITE Le manuel du propriétaire

Allmand MAXI-LITE Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents