White Mountain Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

Marque: White Mountain Hearth

Modèle: Outdoor Linear Fireplace 48 (OLL48FP/SP)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

OUTDOOR LINEAR

GAS FIREPLACE

MODELS

OLL48FP12S(N,P)-2

OLL48SP12S(N,P)-2

GAS-FIRED

WARNING

Do not store or use gasoline or other ammable vapors and

liquids in the vicinity of this or any other appliance.

An propane-cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the replace.

2. Extinguish any open ame.

3. If odor continues, keep away from the replace and im-

mediately call your gas supplier or re department.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instruc-

tions, this product could expose you to sub-

stances in fuel or from fuel combustion which

can cause death or serious illness.

WARNING

Improper installation, adjustment, alteration,

service or maintenance can cause injury or

property damage. Read the installation, operat-

ing and maintenance instructions thoroughly

before installing or servicing this equipment.

WARNING

If the information in these instructions are

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

WARNING

For Outdoor Use Only.

— Installation and service must be per-

formed by a qualied installer, service

agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Page 1

35305-11-0519Page 2

BEFORE YOU START

1. Read the safety information on pages 4, 32 and 33.

2. What to consider before installing. See Page 9.

Water drainage is required. See page 10. Optional drain

tray available.

4. Where are you going to install the unit? See pages 9 to 10.

5. Frame the opening. See pages 6-8 and 12.

6. Installthereplace.Seepages12to14.

7. Connect the electricity. See pages 15 and 24.

8. Connect the gas. See page 16 to 18.

9. Install the crushed glass. See page 20.

10. Lightthereplaceandtroubleshoot.Seepages21and26.

11. Showthehomeownerhowtooperatethereplace.See

page 23.

12.

Show the homeowner how to do the basic maintenance.

See page 25.

CARTON CONTENTS

INDEX

NO.

DESCRIPTION

QUANTITY

SUPPLIED

OLL48FP OLL48SP

1 Glass Panel 1 2

2 Non-Combustible Panel - Top 2 4

3 Non-Combustible Panel - Side 2 4

4 Envelope 1 1

5 Nailing Flange 4 8

6 Top Mounting 3 6

7 Receptacle 1 1

8 Cover Plate 1 1

9 Conduit Connector 1/2-in. 1 1

10 AA Battery 1 1

11 Burner Service Support 2 2

See Parts Lists on pages 28 to 31 for ordering replacement parts.

Do not order batteries, bolts, screws, washers or nuts. They are

standard hardware items and can be purchased at any local

hardware store.

HARDWARE PACK CONTENTS

1-1/4” PHILLIPS DRYWALL SCREW (20)

#10-32 X ½” STAINLESS HEX HEAD SCREW (16)

#10-32 X 1/2" STAINLESS HEX HEAD SCREW

14 - OLL48FP12S(N,P)

28 - OLL48SP12S(N,P)

1-1/4" PHILLIPS DRYWALL SCREW

33 - OLL48FP12S(N,P)

66 - OLL48SP12S(N,P)

1-1/4” PHILLIPS DRYWALL SCREW (20)

#10-32 X ½” STAINLESS HEX HEAD SCREW (16)

35305-11-0519 Page 3

TABLE OF CONTENTS

Before You Start ..........................................................................................................................2

Table Of Contents ........................................................................................................................3

Introduction .................................................................................................................................4

Specications ..............................................................................................................................5

Accessories .................................................................................................................................5

Combustible Materials ................................................................................................................6

Clearances ................................................................................................................................6-7

Fireplace Dimensions .................................................................................................................8

Planning Installation ..............................................................................................................9-11

Fireplace Framing And Installation ....................................................................................12-19

- Framing & Installation ......................................................................................................12-13

- Electrical Supply....................................................................................................................14

- Gas Supply............................................................................................................................15

- Propane Gas Cylinder Information ................................................................................... 16-17

- Finishing ........................................................................................................................... 18-19

Lighting Instructions .................................................................................................................20

Main Burner Flame Characteristics .........................................................................................21

Operation Instructions/Flame Appearance .............................................................................22

Wiring .........................................................................................................................................23

Maintenance...............................................................................................................................24

Troubleshooting ........................................................................................................................25

Master Parts Distributor List ....................................................................................................26

How To Order Repair Parts .......................................................................................................26

OLL48FP12S Parts List .............................................................................................................28

OLL48FP12S Parts View ...........................................................................................................29

OLL48SP12S Parts List.............................................................................................................30

OLL48SP12S Parts View ...........................................................................................................31

Important Safety Information ...................................................................................................32

Safety Information For Users Of Propane Gas .......................................................................33

Appliance Service History ........................................................................................................34

Warranty Terms .........................................................................................................................35

SECTION PAGE

35305-11-0519Page 4

INTRODUCTION

When installed on exterior walls: Empire Comfort Systems

recommends the replace chase be constructed outside the

structure's weather envelope. Where the platform meets the wall,

useaashingdetail similarto thatrequired forattached decks.

Chase platforms, including hearths should slope away from the

structureat1/4in.perfoot.Thereplacecanbeshimmedlevel.

When installed on surfaces where water may collect or cause

damage: Empire Comfort Systems recommends a slope of 1/8 to

1/4in.perfoottowardsthedrainportsuggested.Thereplacecan

be shimmed level.

Hearthsshouldslopeawayfromthefrontofthereplaceandchase

at 1/8 in. to 1/4 in. per foot. Metal safety strips must be on top of

any combustible hearth materials used for moisture management.

Whenpurchasingareboxorreplacewerecommendyoualso

buy a weather cover to protect the unit from moisture. Never install

a burner where moisture cannot drain off easily. We recommend a

weather barrier to protect the burner from moisture.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performedonlybyaqualiedagency.Theterm"qualiedagency"

meansanyindividual,rm,corporationorcompanywhicheitherin

person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

suchwork,familiarwithallprecautionsrequiredandhascomplied

with all the requirements of the authority having jurisdiction.

Local Codes

• Whenthereplaceisconnectedtoaxedpipingsystem,the

installation must conform with local codes, or in the ab-

sence of local codes with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or International Fuel Gas Code.

• Wheninstalled,thereplacemustbeelectricallygrounded

in accordance with local codes, or in the absence of local

codes with the National Electrical Code, ANSI/NFPA 70, if

applicable.

Commonwealth of Massachusetts: The installation must be

madebyalicensedplumberorgastterintheCommonwealth

of Massachusetts.

The installation must conform with local codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1.*

*Available from the American National Standards Institute, Inc. 1430

Broadway, New York, N.Y. 10018.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), ratings should be

reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level. Contact the manufacturer or your gas company before

changingspud/oricesize.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner fill out and mail registration

card supplied with this fireplace or register online at

www.empirecomfort.com.

3. Installer should show owner how to start and operate outdoor

replace.

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of an outdoor

gasreplace.

*Aftermarket: Completionofsale,notforpurposeofresale,from

the manufacturer.

Well Head Gas Installations

Some natural gas utilities use "well head" gas. This may affect the

Btu output of the unit. Contact the gas company for the heating value.

Contact the manufacturer or your gas company before changing

spud/oricesize.

WARNING

This replace is not for use with solid fuels.

WARNING

ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN

BE DANGEROUS.

Improper installation or use of the replace can cause seri-

ous injury or death from re, burns, explosion or carbon

monoxide poisoning.

Thisseriesisdesigncertiedinaccordancewith

ANSI Z21.97/CSA

2.41 for Outdoor Gas Fireplaces

and should be installed according

to these instructions.

Any alteration of the original design, installing it other than as

shown in these instructions or using a type of gas not shown

on the rating plate, is the responsibility of the person and

company making the change.

Manual Valve Safety System

When the burner ignites, a thermocouple senses a signal (electrical

current) that energizes a magnet in the gas valve. After 30 to 60

seconds,the controlknobcan bereleased. Ifthethermocouple

doesnotsensetheame,thegaswillshutoff.

Important

All correspondence should refer to complete Model Number, Serial

Number and type of gas.

Moisture Resistance

Thisoutdoorreplacewillshedmoderateamountsofwater,butis

not waterproof. Water and condensing water vapor may enter the

chase under certain conditions.

Thereplacewillnotperformasanexteriorwall.Moisturepenetration

must beconsideredfor construction that places thereplacein

structure walls or on moisture sensitive surfaces.

35305-11-0519 Page 5

SPECIFICATIONS

DECORATIVE CRUSHED GLASS

Required Decorative Crushed Glass Media Kits (8 Sq. Ft. Required for Burner and LED Lighting)

Model Description

DG1CLF* Clear Frost

Decorative Crushed Glass (For Accent Only)

Model Description

DG1BKP* BlackPolished

DG1BUC* Blue Clear

*Clear Frost Decorative Crushed Glass is required. Decorative Glass Droplets can not be substituted for crushed glass. One bag of

crushed glass covers 1 sq. ft. Enough crushed glass to cover 8 sq. ft. is required. Glass colors may be mixed. The maximum amount

of Crushed Decorative Glass allowed is 8 bags. Transparent and Translucent crushed glass will allow LEDs to better shine through.

DECORATIVE GLASS DROPS 1-IN. (MAY BE USED IN ADDITION TO CRUSHED GLASS)

Model Description

DG1NXS Onyx Solid

DG1RYC Ruby Clear

DG1TZC Topaz Clear

DECORATIVE GLASS DROPLETS 1/2-IN. (MAY BE USED IN ADDITION TO CRUSHED GLASS)

Model Description

DG1AB Aqua Blue

DG1GC Glacier Ice

DG1SL Sangria Luster

Note: Decorative Glass Droplets may be added on top of the crushed glass as an enhancement. Decorative Glass Droplets must not

beplacedintheburnerame.SeeCrushedGlassInstallation,Page20.DonotaddmorethanonebagofDecorativeglassdroplets.

ACCESSORIES

Model Description

DT48LSS Stainless Steel Drain Tray - 48-in

WD48LSS StainlessSteelWeatherDoor-48-in(ordertwoforsee-throughreplaces)

WG48LT1 DeectorGlassforWindyApplications-48-in(ordertwoforsee-throughreplaces)

33815 Natural to Propane Conversion Kit

33814 Propane to Natural Conversion Kit

ACCESSORIES

Model Number OLL48FP (Natural) OLL48FP (Propane) OLL48SP (Natural) OLL48SP (Propane)

Input BTU/Hr Maximum 55,000 55,000 55,000 55,000

Input BTU/Hr Minimum 35,000 35,000 35,000 35,000

KWH Maximum 16.12 16.12 16.12 16.12

KWH Minimum 10.26 10.26 10.26 10.26

Orice #24 #44 #24 #44

Air Shutter Setting 1/16" Open 3/8" Open 1/16" Open 3/8" Open

Gas Inlet Shut-Off Valve Pipe

1/2 NPT 1/2 NPT 1/2 NPT 1/2 NPT

GAS SUPPLY PRESSURES (INCHES WATER COLUMN)

Gas Type Maximum Minimum Manifold

Natural 14 4.5 3.5

Propane 14 10.8 10

35305-11-0519Page 6

CLEARANCES

Index

Letter

Description

Dimension from

Fireplace Opening

(in inches)

From ground or other

non-combustible surface

10-1/4*

B From Side Walls 6

C From Ceiling 24

D Alcove Width (minimum) 60

E Alcove Depth (maximum) 24

*NOTE: DimensionAincludes3-1/2in.underreplacefor

support framing and drain tray installation.

Figure 3 - Alcove Clearances

Minimum Wall and Ceiling Clearances

SidewallClearances:Theclearancefromtheinsideofthereplace

to any combustible wall should not be less than 6 in.

Ceiling Clearances: The ceiling height should not be less than

24 in. from the top opening.

Mantel Clearances: If a combustible mantel is installed, it must meet

the clearance requirements detailed in Figure 2.

Figure 2 - Mantel Clearances

Donotattachcombustiblematerialtothemantelofyourreplace.

Thisisarehazard.

Figure 1

COMBUSTIBLE MATERIALS

Nogreetingcards,stockingsorornamentationofanytypeshouldbe

placedonorattachedtothereplace.Thisisaheatingappliance.

Theowofheatcanignitecombustibles.

NOTE: Forsee-thrureplaces,thisappliestobothsidesofthe

unit.

Television Considerations

Installingatelevisionaboveareplacehasbecomeincreasingly

popular;however,theareaaboveanyreplacegetshotandmost

TV manufacturers recommend against placing their products near

a heat source.

Ifyouinstallatelevisionabovethisreplace,EmpireComfortSys-

tems accepts no responsibility for damage or injuries. Follow the

television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.

IfyouhaveaTVaboveyourreplace,turnoffthereplaceand

let it cool completely before servicing or touching any buttons on

the TV.

35305-11-0519 Page 7

Figure 4

Front and Side View of Non-Combustible Panel to Opening on Fireplace's Face

NOTE: Recommendedinstallationifusing6in.orsmallertilesornishingmaterials.

CLEARANCES

Figure 5

Front View and Side Prole of Non-Combustible Panel to Top of Fireplace

NOTE: Recommendedinstallationifusing6-in.orlargertilesornishingmaterials.

Note for Figures 4 and 5:Ifinstallingthewallboardintheushfaceconguration,trimthetwotoppanelsto16-1/2in.x26-3/4in.The

smaller non-combustible panels will not be needed.

35305-11-0519Page 8

FIREPLACE DIMENSIONS

INDEX

LETTER

DIMENSION DESCRIPTION

OLL48FP OLL48SP

Dimensions in Inches

A Themaximumheightofreboxface(excludingstandoffs) 24-5/16 24-5/16

B Themaximumwidthofthereboxface(excludingnailinganges) 51-3/4 51-3/4

C Themaximumdepthoftherebox 19-1/16 22-5/16

D Theheightofthereboxopening 16-3/16 16-3/16

E Thewidthofthereboxopening 48 48

F Theinteriordepthoftherebox(notshown)

19 22-9/32

G Therearexteriorwidthoftherebox(notshown) 51-3/4 51-3/4

H Theheighttothereboxstandoffs 16-1/2 16-1/2

I Width from the left side of the box to the centerline of vent N/A N/A

J Depthfrombackofboxtocenterlineoftopvent N/A N/A

K Height from the bottom of the box to the gas line opening 2-9/16 2-9/16

L Depth from the front of the box to gas line opening 5-3/16 5-3/16

M Depth from rear of box to gas line opening 13-21/32 N/A

N Glass height 3-1/2 3-1/2

O Glass width 47-3/8 47-3/8

P Depth from front of box to centerline of vent N/A N/A

Q Distancefromoortoreplaceopening 6-11/16 6-11/16

R Heightfromoortoventcollar N/A N/A

S Overall height to header 40-13/16 40-13/16

N/A - Not applicable for this unit.

35305-11-0519 Page 9

What to Consider Before Installing

1. Verifyreplacegastypeandgassupplytypearethesame.

2. Lookforalocationwherecombustibleswillnotinterfere.

3. 120V GFI power outlet will be needed for LED lights

4. Choose a location for gas shutoff valve.

5. Verify ventilation meets at least minimum requirements

6. Wind and rain direction

7. Drainageunderreplace.

8. Consideration drain pan and weather door accessories.

9. Glass accessories

Inplanningthe installation forthereplace, it isnecessaryto

determine where the unit is to be installed and whether optional

accessories are desired. Gas supply piping should also be planned

at this time.

Thereplacecanbemountedonanyofthesesurfaces:

1. A raised frame of combustible material so contact is made on

allfourperimeteredgesofthebottomofthereplaceatleast

3-1/2in.abovetheoor.

2. Four corners ofthe replace socontact is madeon all four

perimeter edges on the bottom of the unit at least 3-1/2 in.

abovetheoor.Checklocalcodesforallowances.

At this point, you should have decided what components to include

inyourinstallation,andwherethereplaceistobelocated.Ifthis

has not been done, stop and consult your dealer for assistance

with this planning.

WARNING

This replace is intended for installation on an outdoor patio

or yard. This replace shall be used only outdoors in a well

ventilated space and shall NOT be used in a building, garage,

or other enclosed area. This replace cannot be installed

with an opening to the inside of a residence.

NOTICE: This fireplace is NOT equipped with an Oxygen

Depletion Sensor (ODS) pilot.

Itisrecommendedthatthisreplacebeinstalledina“sheltered”

area.Directwind will cause anerraticame and possible main

burneroutage. Thiserraticame could also leadto excessive

blacksoot.Theseissuesarenuisanceissuesratherthanasafety

issues. Avoid areas where excessive moisture or running water may

benearoronreplace.

Typical installation may include covered patio, open porch, gazebo

or an outside wall of a house.

• Minimum porch area – 96 square feet

• Minimum ceiling height – 90 inches

LED Lights will require a 120V GFI power outlet on the valve side of

thereplace.TheGFIplugwillbelocatedoutsideofthereplace.

Ajunctionboxisprovidedinsidethereplacetoprovidealocation

to plug in the LEDs.

Outdoor Fireplace Enclosure Requirements

Donotinstallreplaceuntilallnecessaryprovisionsaremadefor

combustion and ventilation air. Consult the written instructions

providedwiththereplaceforinformationconcerningcombustion

and ventilation air. In the absence of instructions, refer to the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion

and Ventilation, or applicable local codes.

Installation must conform with one of the following conditions:

• With walls on all sides, but with no overhead cover.

See Figure 6.

Figure 6

• Within a partial enclosure which includes an overhead cover

and no more than two side walls. These side walls may be

parallel, as in a breezeway or at right angles to each side.

See Figure 7.

Figure 7

PLANNING INSTALLATION

35305-11-0519Page 10

PLANNING INSTALLATION

• Within a partial enclosure that includes an overhead cover and

three side walls, as long as 30 percent or more of the horizontal

periphery (perimeter of walls and open side) of the enclosure

is permanently open. See Figure 8.

Figure 8

If installing in a screened in porch, the open space must be adjusted

(increased) from 30 percent (adjusted open space = 30% / % open

area of the screen mesh). "Example, if you used a screen with a

66% open area, the minimum open space of your building must

be 46% of the periphery. If you have a covered screened-in porch

that has two side walls that are 16', one wall that was against the

house that's 20' and one open side that's 20', you would have a

perimeter of 72'. You would need to have 33' of the perimeter open

(72' x 46% = 33')."

(Contact your screen manufacturer or screen dealer to

determine your screens open area).

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

or loss of life. Installation and service must be performed

by a qualied installer, service agency or the gas supplier.

Gas Line Connection

Thereplaceisdesignedtoaccepta1/2in.gasline.Havethe

lineinstalledbyaqualiedservicepersoninaccordancewithall

building codes. Consult local building codes to properly size the gas

supplylineleadingtothe1/2in.hook-upattheunit.Thestateof

Massachusettsrequiresthataexiblereplaceconnectorcannot

exceed three feet in length.

Aex-lineconnectiontothevalveshashavebeenprovided.The

gas shut-off valve must be located outside of the unit in an

accessible area.

Checkgastypeontheratinglabellocatedonthebackofthecontrol

door. If the gas listed on the rating label located on the control pane,

does not match your gas supply, DO NOT INSTALL. Contact your

dealerforpropermodelorconversionkit.

AlwaysuseanexternalregulatorforallPropanereplacestoreduce

thesupplytankpressuretoamaximumof13in.w.c.

WARNING

Connection directly to an unregulated propane tank can

cause an explosion.

WARNING

Risk of re, explosion or asphyxiation. Ensure no ignition

ame or spark are near during installation. This includes

cigarettes or cell phones.

Leaktestallconnectionswithasoapandwatersolution.Bubble

formationwillindicatealeak.Usecautiontoavoidburns.

Figure 9

Water Drainage Requirement

Provisions must be made to drain water away from the unit. An

optional drain pan can be purchased from your Empire Dealer to

tunderthereplace.Ifinstallingtheoptionaldrainpan,itmust

beinstalledpriortoinstallingthereplace.Formoreinformation,

refer to the installation instructions supplied with the drain pan. If

this drain is not used, other water drainage is required.

35305-11-0519 Page 11

Electrical Considerations

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The replace,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

A factory installed junction box is located on the lower right side

ofthereplace.Thejunctionboxandwiringmayberelocatedto

theoppositesideofthereplaceifdesired.Wiringtothejunction

box must be metal clad or enclosed in a conduit and must be

approved for outdoor use. Connect the wiring to an external GFI

protectedoutletinstallednearthereplace.See Figure 10.

Figure 10

PLANNING INSTALLATION

35305-11-0519Page 12

FIREPLACE FRAMING AND INSTALLATION

Unpacking the Fireplace

After removal of the cardboard carton, remove the band hold-

ing the corner posts, non-combustible board and top mounting

standoffstothereplace.Setthenon-combustibleboardandtop

mounting standoffs aside, discard the corner posts.

Toremovethereplacefromthepallet,removeanddiscardthe

blackclipsandscrewsfasteningeachendofthereplacetothe

pallet.

Removeanyprotectivelmfromreplaceandallcomponents

(nailinganges,standoffs,etc.).

Figure 11

Framing

Fireplacesupportframingshouldbebuiltbeforethereplaceisset

inplace.Thereplaceframingmaybeconstructedof2x4lumber.

Theframingheadersmustrestonthereplacestandoffs.Referto

Figure 12 for minimum framing dimensions.

CAUTION

Measure replace dimensions and verify framing methods,

and wall covering details before framing construction begins.

Framing dimension A includes a 16-1/2 in. clearance for

standoffs on rebox. After installing rebox into framing, the

nished wall surface must cover the 16-1/2 in. opening above

the rebox.

KEEP OPEN

AREA FOR

DRAINAGE

INSTALL AFTER INSTALLATION

OF FIREPLACE IF DRAIN TRAY

IS USED

WATER

DRAINAGE

THIS SIDE

FRAMING DIMENSIONS (in inches)

OLL48FP OLL48SP

Height A 40-13/16 40-13/16

Width B 52 52

Depth C 19-1/16 22-5/16

Figure 12 - Fireplace Framing

Beforecompletingtheframingandinstallingreplace,providea

pathforwaterdrainageoutofthereplace.

Determine if the optional accessory drain pan will be used. See

Page 13. If the drain pan will be installed, follow the instructions

providedwiththedrainpankittoinstallitatthispoint.

Installation

1. Choose installation location.

2. Constructthesupportframingforthereplace.Seeframing

dimensions, Figure 12. See Clearances, Pages 6 and 7.

3. Locatethenailingangesintheinstallationenvelopeand

attachthemtothesidesofthereplacewithtwo#10-32x1/2

hexscrewseach.Theangeshavethreepositionsto

accommodate the wall board being installed over the face of

theunit(cleanface)orushwiththefaceoftheunitwith

1/2in.or5/8in.thickwallboard.See Figure 13.

Figure 13

4. Bendthenailingangetabsoutatrightangles.Forsee-

throughreplacesonlybendthetabsononesideofthe

replacetoallowthetabsontheothersidetoclearthe

enclosure framing.

5. Liftthereplaceandsetintotheframe.Slidethereplace

backuntilnailingangesmeettheframe.Securethere-

place to the frame with one #8x1 drywall screw each. For

see-thrureplaces,bendthebacksidenailingangesout

and right angles and secure with one #8x1 drywall screw

each.

Figure 14

FRAMING & INSTALLATION

35305-11-0519 Page 13

FIREPLACE FRAMING AND INSTALLATION

6. Locatethetopstandoffs(threeforsingle-sidedreplaces

andsixforsee-throughreplaces).Bendmountingfeetand

attachtothetopofthereplacewithtwo#10-32x1/2hex

screws each.

Figure 15

The standoffs may be installed in one of three positions to

accommodate installing the wall board over the front of the

replace(cleanface)orushwiththereplacewith1/2in.or

5/8in.thickwallboard.

See Figure 16.

Figure 16

7. Secure the top of the standoffs to the header.

8. To connect the gas line and install the electrical connection,

theburnerassemblymustbetiltedupwardinthereplace.

To lift the burner assembly, remove the control door by open-

ing the door and lifting it upward to disengage the slots on

the door from the pivot pins.. Remove the two control door

pivot bolts and washers. See Figure 17.

Figure 17

9. Remove two screws from front corners of the control panel

with a Phillips head screw driver. See Figure 18.

Figure 18

FRAMING & INSTALLATION

35305-11-0519Page 14

FIREPLACE FRAMING AND INSTALLATION

FRAMING & INSTALLATION

10. Lift front of burner assembly and tilt upwards and toward the

backofthereplace.Retrievethetwosupportsfrominside

thereplaceandplaceoneeachsideagainstthefrontcor-

ners of the cabinet bottom and under the front corners of the

control panel.

PROP SUPPORT

IN FOUR CORNERS

Figure 19

11. Installgasandelectricalsuppliestoreplace.Seepage16

for gas supply requirements. For ease of installation, the

gas and electrical supply are located on the valve side of the

replace.Bothmayberelocatedtoentertheoppositesideof

thereplace.

35305-11-0519 Page 15

FIREPLACE FRAMING AND INSTALLATION

Figure 20

GROUND

CONDUIT

RECEPTACLE

120 VOLT

POWER SUPPLY

OUTLET

COVER

GASKET

Figure 21

ELECTRICAL SUPPLY

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The replace,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

Wiring to the junction box must be metal clad or enclosed in a

conduit and must be approved for outdoor use. A connector for

the junction box to accommodate 1/2-in. conduit is supplied in the

instructionenvelope.Thereplacereceptaclemustbeconnected

toanexternalGFIprotectedoutletinstallednearthereplace

See Figure 20.

Route the wiring from the external GFI outlet through the conduit

to the junction box. Leave approximately 6-in. of wire in the junc-

tion box for connection.

Retrieve the receptacle and cover from the instruction enve-

lope.Attachtheblackwireandwhitewiretothereceptacle.The

ground wire should be attached to the green (ground screw on

the junction box and the receptacle.

Placereceptacleinpositionandattachcoverplate.Makesure

the cover plate doors open upward. Be sure to test the receptacle

to ensure the GFI circuit functions properly. Plug transformer

power cord into receptacle, and close the unused receptacle

door.

35305-11-0519Page 16

FIREPLACE FRAMING AND INSTALLATION

• Solidfuelsshallnotbeburnedinthisreplace.

• The maximum gas inlet supply pressure is 11 in. for Propane

and 10.5 in. for Natural.

• Forreplacesforxedfuelpipingsystemandequippedwith

areplacegaspressureregulator,therequiredmanifold

pressure in inches water column: 11 in. for Propane and

4.5 in. Natural.

• Forreplacesforxedfuelpipingsystemandequippedwith

areplacegaspressureregulator,thereplaceanditsindi-

vidual shutoff valve must be disconnected from the gas sup-

ply piping system during any pressure testing of that system

attestpressuresinexcessof1/2psi(3.5kPa).

Thereplacemustbeisolatedfromthegassupplypiping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressuresequaltoorlessthan1/2psi(3.5kPa).

Checkalllocalcodesforrequirements,especiallyforthesizeand

type of gas supply line required.

RECOMMENDED MINIMUM GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2 in.

12.7mm

3/8 in.

9.5mm

1/2 in.

12.7mm

3/8 in.

9.5mm

10-40 feet

4-12 meters

1/2 in.

12.7mm

1/2 in.

12.7mm

5/8 in.

15.9mm

1/2 in.

12.7mm

40-100 feet

13-30 meters

1/2 in.

12.7mm

1/2 in.

12.7mm

3/4 in.

19mm

1/2 in.

12.7mm

100-150 feet

31-46 meters

3/4 in.

19mm

1/2 in.

12.7mm

7/8 in.

22.2mm

3/4 in.

19mm

NOTE:Neveruseplasticpipe.Checktoconrmwhetheryourlocal

codes allow copper tubing.

NOTE: Because some municipalities have additional local codes,

consult your local authority and installation code.

Installing a Manual Gas Shut-Off

Eachreplacemusthaveanaccessiblemanualgasshut-offlocated

in the vicinity of the unit. Where none exists, or where its size or

location is not adequate, contact your local authorized installer for

installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checkedforleaksbytheinstaller.Thisshouldbedonewithasoap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

Never use an exposed ame to check for leaks. Fireplace must

be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

replace connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

the National Fuel Gas Code that a drip line be installed near the gas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

The use of the following gas connectors is recommended:

— ANSI Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANSI Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction The Commonwealth of Massachusetts requires

thataexibleapplianceconnectorcannotexceedthreefeetinlength.

NATURAL

GAS SUPPLY

SHUT

-OFF

LVE

FLEX TUBING

MALE NPT to

MALE FLARE

REGULATOR

NIPPLE

NATURAL

GAS SUPPLY

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

SHUT-OFF

VALVE

FLEX TUBING

MALE NPT to

MALE FLARE

VALVE

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

VALVE

FEMALE NPT to

FEMALE NPT

FEMALE NPT to

FEMALE NPT

Figure 22

NOTE: Gas shut-off shown. Other valves approved to use with

gas allowed.

Flex tubing to valve is pre-installed at the factory. Flare connector

is located in the envelope.

An accessible manual gas shut-off valve must be installed

externaltothereplace.

GAS SUPPLY

35305-11-0519 Page 17

WARNING

If these instructions are not followed exactly, a re caus-

ing death or serious injury may occur.

Propane Cylinder Specications

Thisreplacecanbeusedwithanon-disposableself-contained

Propane Gas supply system:

• Propane cylinders may be acceptable for use with the

replaceprovidedtheyarecompatiblewiththereplace

retention means.

• Propane Gas supply cylinder must be constructed and

markedinaccordancewiththeU.S. Department of

Transportation (D.O.T.) Specications for Propane Gas

Cylinders, or the Standard for Cylinders, Spheres and

Tubes for Transportation of Dangerous Goods and Com-

mission, CAN/CSA-B339 as applicable.

• Propane Gas supply cylinders between 4 and 40

poundsmusthaveanoverllpreventiondevice.

• Propane Gas supply cylinder must have a connection

devicecompatiblewiththeconnectionofthereplace.

• IfthereplaceisequippedwithaCGANo.600Cylinder

Connection Device, the cylinder must be disconnected

whenthereplaceisnotinuse.

• Ifreplaceistobepermanentlyconnectedtoagaspip-

ingsystemfromaremotesupplytank,installationmust

be in accordance with local codes or, in the absence

of local codes, with the National Fuel Gas Codes ANSI

Z223.1/NFPA 54.

• A dented or rusty cylinder may be hazardous and should

becheckedbyyourpropanesupplier.Neveruseacylin-

der with a damaged valve.

• Thisreplacemaybeusedwitha20lb.(9.1kg)or30lb

(13.6kg)sizepropanecylinderonly(notsupplied).

• The propane cylinder must be provided with a shut-

off valve terminating in a propane cylinder valve type

QCC1, and a safety relief device having direct commu-

nication with the vapor space of the cylinder.

• The cylinder supply system must be arranged for vapor

withdrawal and the cylinder shall include a collar to

protect the cylinder valve.

• The Propane Gas cylinder must be provided with a

listedoverllprotectiondevice(OPD).Neverllthe

cylinder beyond 80 percent full.

• Do not store a spare Propane Gas cylinder under or

nearthisreplace.

• Use only a pressure regulator and hose assembly that

suppliesapressureof11in.watercolumntothere-

placeandhasaQCC1typetting.

• Cylinders to be used with this unit must be supplied with

a QCC1 cylinder valve. A QCC1 cylinder has a positive

seatingconnection,whichwillnotallowgasowuntila

positive seal has been achieved. It is also equipped with

anexcessowdevice.Inordertoattainfullowtothe

replace,thevalvemustbeintheoffpositionwhenthe

cylinder valve is turned on.

WARNING

A re will result if the gas supply hose makes contact with

the underside of the replace.

Propane Gas

Attachcylinderretainingbracketsuppliedtothebaseofthecyl-

inder. Then secure to the surface to which it sits. Cylinder should

be on a level surface.

Cylinder Retaining Bracket

1. Fastenthebrackettothebottomofthepropanebottleusing

bolt and nut (not supplied).

2. Tighten the lag screw into the mounting surface leaving ap-

proximately 1/4 in. of thread above the surface.

3. Slidepropanebottleintopositionsothatthebracketslides

under the head of the lag screw.

4. Tightenthelagscrewontothebracket.

5. For fastening to a concrete surface a concrete anchor will be

required. (Not supplied)

Cylinder Connection:Ensurethegasregulatorhoseiskink

free. Remove the cap or plug from the cylinder fuel valve. Insert

theblackQCC1regulatornippleontotheQCC1fuelvalve.Hand

tightenclockwise.Donotusetools.Leaktestalljointspriorto

usingthereplace.Aleaktestmustbeperformedannuallyand

eachtimeacylinderishookeduporifapartofthegassystem

isreplaced.Ifthisreplaceistobeconnecteddirectlytoahouse

propane gas supply line, follow the instructions for the natural

gashook-up.

Safety Considerations

• Makesurecylindervalveisinitsfulloffposition.(Turnclock-

wise to stop).

• Checkcylindervalvefeaturestoensureithasproperex-

ternalmatingthreads.(CylinderValveMarked:USEWITH

TYPE 1)

• Inspect hose for damage. Never attempt to use damaged or

plugged equipment. See your local Propane Gas Dealer for

repairs.

• When connecting regulator assembly to the cylinder valve,

handtightenblackQCC1nutclockwisetoapositivestop.

DO NOT use a wrench to tighten. Use of a wrench may dam-

agethequickclosingcouplingnutandresultinahazardous

condition.

• Locate the hose out of pathways where people may trip over

it or in areas where the hose may be subject to accidental

damage.

• Opencylindervalvefully(counter-clockwise).Turntheshut

off valve at the unit slowly to the on position and use a soapy

watersolutiontocheckallconnectionsforleaksasindicated

inthediagramsbeforeattemptingtolightthereplace.Ifa

leakisfound,turntankvalveoffanddonotusethereplace

until repairs can be made.

FIREPLACE FRAMING AND INSTALLATION

PROPANE GAS CYLINDER INFORMATION

35305-11-0519Page 18

Enclosures For Propane Gas Supply Systems

Enclosures for Propane Gas supply cylinders shall be ventilated

byopeningsatthelevelofthecylindervalveandatoorlevel.

The effectiveness of the opening(s) for purposes of ventilation

shall be determined with the Propane Gas supply cylinder(s) in

place. This shall be accomplished by one of the following.

a. One side of the enclosure shall be completely open; or

b. For an enclosure having four sides, a top and a bottom:

1. At least two ventilation openings at cylinder valve level

shall be provided in the side wall, equally sized, spaced

at 180 degrees (3.14 rad), and unobstructed. Each

opening shall have a total free area of not less than

1/2sqinperpound(2.3sq.cm/kg)ofstoredfuelcapac-

ity and not less than a total free area of 10 sq in (64.5

sq. cm).

2. Ventilationopening(s)shallbeprovidedatoorlevel

and shall have a total free area of not less than 1/2 sq in

perpound(3.2sq.cm/kg)ofstoredfuelcapacityandnot

less than a total free area of 10 sq in (64.5 sq. cm). If

ventilationopeningsatoorlevelareinasideall,there

shall be at least two openings. The bottom of the open-

ingsshallbeatoorlevelandtheupperedgenomore

than5in.(127mm)abovetheoor.Theopeningsshall

be equally sized, spaced at 180 degrees (3.14 rad) and

unobstructed.

3. Every opening shall have minimum dimensions so as to

permit the entrance of a 1/8 in. (3.2 mm) diameter rod.

4. There shall be a minimum clearance of 2 in. (51 mm)

betweenthelowersurfaceoftheoorofthePropane

Gas supply cylinder enclosure and the ground.

• Cylinder valves shall be readily accessible for hand opera-

tion. A door on the enclosure to gain access to the cylinder

valvesisacceptable,provideditisnon-lockingandcanbe

opened without the use of tools.

• Thedesignofthereplaceshallbesuchthat(1)the

Propane Gas supply cylinder(s) can be connected, discon-

nected and the connections inspected and tested outside the

cylinder enclosure; and (2) those connections which could

be disturbed when installing the cylinder(s) in the enclosure

canbeleaktestedinsidetheenclosure;

• Ventilation openings in sidewalls shall not communicate

directlywithotherenclosuresofthereplace.

The enclosure for the Propane Gas cylinder shall isolate the

cylinder from the burner compartment to provide:

a. Shielding from heat radiation;

b. Aamebarrier;and

c. Protection from foreign material.

Be certain to mount or set the Propane Gas cylinder on a at

surface and restrain it using a cylinder retaining bracket to

prevent it from tipping.

NON-LOCKING

DOOR

TOP AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPLACE

OPENING B

OPENING A

1” MAX

5” MAX

TOP AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPLACE

FIREPLACE POSITIONED

ABOVE TANK ENCLOSURE

FIREPLACE POSITIONED

BESIDE TANK ENCLOSURE

5” MAX

1” MAX

2” MIN

Cylinder

Size

Opening

Area A

Opening

Area B

Recommended

Dimension C

20lb

(9.1kg)

20 sq.in.

(130cm

)

10 sq.in.

(65cm

)

34 in.

(863mm)

30lb

(13.6kg)

30 sq.in.

(195cm

)

15 sq.in.

(100cm

)

34 in.

(863mm)

NOTE: There shall be a minimum clearance of 2 in. (51 mm)

betweenthelowersurfaceoftheoorofthePropaneGassupply

cylinder enclosure and the ground.

Figure 23

FIREPLACE FRAMING AND INSTALLATION

PROPANE-GAS CYLINDER INFORMATION

35305-11-0519 Page 19

FIREPLACE FRAMING AND INSTALLATION

FINISHING

1. Aftergasandelectricalhookupiscompleted,lowerand

secure the burner assembly (leave two supports in bottom of

replaceforfutureuse)withthetwoscrewsremovedinStep

9 on page 13.

2. Installtheglasswindpanel(twousedonsee-throughre-

places). See Figure 24.

Figure 24

3. Reinstall the pivot bolts and washers removed in step 8 on

page 13 and reinstall the control door.

4. Unscrew the igniter button and install the AA battery provided

in the instruction envelope prior to closing the control door. See

Figure 25.

Figure 25

Framing and Finishing

Thereplacecanbeinstalledwithpanelsaroundtheopeningas

a clean face installation. See Figure 26. The top and sides must

use non-combustible panels (provided) where shown going over

thefaceofthereplace.Outsideofthisarea,anyweatherproof

wall board may be used.

Figure 26

Thereplacecanalsobeinstalledwithpanelsushwiththe

faceofthereplace.See Figure 27. In this application, the two

top non-combustible panels (provided) are required above the

replace.Outsideofthisareaincludingthesidesoutsideofthe

replace'smetalmaybeanyweatherproofwallboard.

Figure 27

To complete installation place non-combustible panels above

replaceopening.Centerpanelsonreplaceandsecurewith

screws into frame. With the non-combustible panels in posi-

tion, predrill 1/8-in. diameter holes through the non-combustible

panels and top mounting standoffs before running the screws into

the top mounting standoff. Place non-combustible panels on the

sidesofthereplaceopening.Securewithscrewsintotheframe

andpre-drill1/8-in.diameterholesintothereplaceface.Finish

remaining wall with weather-proof wall board.

NOTE: Ifinstallingthewallboardintheushfaceconguration,

trim the two top panels to 16-1/2 in. x 26-3/4 in. The

smaller non-combustible panels will not be needed.

NOTE: Areaswherethelmhasbeenformed(corners,hems,

etc.) may require extra cleaning due to the proper-

tiesofthelm.Ensurethatallprotectivelmhasbeen

removedfromthereplacepriortoburning.

35305-11-0519Page 20

FIREPLACE FRAMING AND INSTALLATION

FINISHING

Crushed Glass Installation

Ensure the burner cover screens are still properly installed, fully

covering the LED openings. Place decorative crushed glass over

the burner cover, screen and burner (enough media to cover ap-

proximately8squarefeet).Somepiecesofbrokenglassmaybe

largerthanothers.Itisnetousethesepieces,butnotoverthe

burneroramearea.See Figure 28.

Decorative glass droplets may be added, but can not be used

near or over the burner. See Figure 29. Neither glass nor drop-

letsmaybeplacedoverthesparkprobe.

Figure 28

Figure 29

La page charge ...

White Mountain Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

Marque: White Mountain Hearth

Modèle: Outdoor Linear Fireplace 48 (OLL48FP/SP)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: White Mountain Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Owner's manual

White Mountain Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

White Mountain Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents