Makita LS1019 Slide Compound Miter Saw Manuel utilisateur

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

Slide Compound Miter Saw

Scie à Onglet Radiale

Sierra de Inglete Telescópica

LS1019

LS1019L

IMPORTANT: Read Before Using.

IMPORTANT : Lire avant usage.

IMPORTANTE: Lea antes de usar.

DOUBLE INSULATION

DOUBLE ISOLATION

DOBLE AISLAMIENTO

https://tm.by

Интернет-магазин TM.by

2ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: LS1019 LS1019L

Blade diameter 255 mm (10″)

Hole diameter 15.88 mm (5/8″)

Max. kerf thickness of the saw blade 3.2 mm (1/8″)

Max. miter angle Right 60°, Left 60°

Max. bevel angle Right 48°, Left 48°

No load speed (RPM) 3,200 /min

Laser type -Wavelength 655 nm, Maximum

output 1mW (Laser

Class II)

Dimensions (L x W x H) 805 mm x 644 mm x 660 mm

(31-3/4" x 25-3/8" x 26")

Net weight 26.1 kg

(57.6 lbs)

26.3 kg

(57.9 lbs)

Cutting capacities (H x W)

Miter angle Bevel angle

45° (left) 0° 45° (right)

0° 47 mm x 305 mm

(1-7/8″ x 12″)

61 mm x 279 mm

(2-3/8″ x 11″)

71 mm x 305 mm

(2-13/16″ x 12″)

91 mm x 279 mm

(3-5/8″ x 11″)

29 mm x 305 mm

(1-1/8″ x 12″)

43 mm x 279 mm

(1-11/16″ x 11″)

45° (right and left) 47 mm x 215 mm

(1-7/8″ x 8-1/2″)

61 mm x 197 mm

(2-3/8″ x 7-3/4″)

71 mm x 215 mm

(2-13/16″ x 8-1/2″)

91 mm x 197 mm

(3-5/8″ x 7-3/4″)

29 mm x 215 mm

(1-1/8″ x 8-1/2″)

43 mm x 197 mm

(1-11/16″ x 7-3/4″)

60° (right and left) -71 mm x 152 mm

(2-13/16″ x 6″)

91 mm x 139 mm

(3-5/8″ x 5-1/2″)

-

Cutting capacities for special cuttings

Type of cutting Cutting capacity

Crown molding 45° type

(with crown molding stopper used)

168 mm

(6-5/8″)

Base board

(with horizontal vise used)

133 mm

(5-1/4″)

•Due to our continuing program of research and development, the specications herein are subject to change

without notice.

•Specications may differ from country to country.

•Weight according to EPTA-Procedure 01/2014

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2.

Do not operate power tools in explosive atmospheres, such

as in the presence of ammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or fumes.

https://tm.by

Интернет-магазин TM.by

3ENGLISH

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5.

When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suit-

able for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a Residual Current Device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

3. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your nger on the switch or energising power tools

that have the switch on invites accidents.

4.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

5. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8.

Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

2.

Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3.

Disconnect the plug from the power source and/

or remove the BATTERY pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

4.

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

5.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

8.

Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasp-

ing surfaces do not allow for safe handling and control

of the tool in unexpected situations.

Service

1.

Have your power tool serviced by a qualied repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

2. Follow instruction for lubricating and chang-

ing accessories.

Ensure the mitre saw is mounted or placed on a level, rm

work surface before use. A level and rm work surface

reduces the risk of the mitre saw becoming unstable.

Additional instructions

1.

To reduce the risk of electric shock, this equipment has

a polarized plug (one blade is wider than the other). This

plug will t in a polarized outlet only one way. If the plug

does not t fully in the outlet, reverse the plug. If it still

does not t, contact a qualied electrician to install the

proper outlet. Do not change the plug in any way.

2. VOLTAGE WARNING: Before connecting the

tool to a power source (receptacle, outlet, etc.)

be sure the voltage supplied is the same as

that specied on the nameplate of the tool. A

power source with voltage greater than that

specied for the tool can result in SERIOUS

INJURY to the user- as well as damage to the

tool. If in doubt, DO NOT PLUG IN THE TOOL.

Using a power source with voltage less than

the nameplate rating is harmful to the motor.

3.

USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an

https://tm.by

Интернет-магазин TM.by

4ENGLISH

extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss

of power and overheating. Table 1 shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage.

The smaller the gage number, the heavier the cord.

Table 1: Minimum gage for cord

Ampere Rating Volts Total length of cord in feet

120V 25 ft. 50 ft. 100 ft. 150 ft.

More Than Not More

Than

AWG

06–18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

Safety instructions for mitre saws

1.

Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as the

lower guard to jam. Sparks from abrasive cutting will burn

the lower guard, the kerf insert and other plastic parts.

2.

Use clamps to support the workpiece whenever pos-

sible. If supporting the workpiece by hand, you must

always keep your hand at least 100 mm from either side

of the saw blade. Do not use this saw to cut pieces that

are too small to be securely clamped or held by hand. If

your hand is placed too close to the saw blade, there is an

increased risk of injury from blade contact.

3.

The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut "freehand"

in any way. Unrestrained or moving workpieces could

be thrown at high speeds, causing injury.

4.

Push the saw through the workpiece. Do not pull the saw

through the workpiece. To make a cut, raise the saw head

and pull it out over the workpiece without cutting, start

the motor, press the saw head down and push the saw

through the workpiece. Cutting on the pull stroke is likely

to cause the saw blade to climb on top of the workpiece and

violently throw the blade assembly towards the operator.

5.

Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece "cross handed" i.e. holding

the workpiece to the right of the saw blade with your left

hand or vice versa is very dangerous.

6.

Do not reach behind the fence with either hand closer than

100 mm from either side of the saw blade, to remove wood

scraps, or for any other reason while the blade is spinning.

The proximity of the spinning saw blade to your hand may not

be obvious and you may be seriously injured.

7.

Inspect your workpiece before cutting. If the work-

piece is bowed or warped, clamp it with the outside

bowed face toward the fence. Always make certain

that there is no gap between the workpiece, fence

and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be

no nails or foreign objects in the workpiece.

8.

Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that contact

the revolving blade can be thrown with high speed.

9.

Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

10.

Ensure the mitre saw is mounted or placed on a level,

rm work surface before use. A level and rm work sur-

face reduces the risk of the mitre saw becoming unstable.

11.

Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool "ON" and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

12.

Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top. Workpieces longer or wider

than the mitre saw table can tip if not securely sup-

ported. If the cut-off piece or workpiece tips, it can lift

the lower guard or be thrown by the spinning blade.

13.

Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

14.

The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade. If con-

ned, i.e. using length stops, the cut-off piece could get

wedged against the blade and thrown violently.

15. Always use a clamp or a xture designed to

properly support round material such as rods

https://tm.by

Интернет-магазин TM.by

5ENGLISH

or tubing. Rods have a tendency to roll while

being cut, causing the blade to "bite" and pull the

work with your hand into the blade.

16. Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the

workpiece being thrown.

17. If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving

parts to stop and disconnect the plug from

the power source and/or remove the battery

pack. Then work to free the jammed material.

Continued sawing with a jammed workpiece could

cause loss of control or damage to the mitre saw.

18.

After nishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

19.

Hold the handle rmly when making an incomplete

cut or when releasing the switch before the saw

head is completely in the down position. The braking

action of the saw may cause the saw head to be sud-

denly pulled downward, causing a risk of injury.

20. Only use the saw blade with the diameter that

is marked on the tool or specied in the man-

ual. Use of an incorrectly sized blade may affect

the proper guarding of the blade or guard opera-

tion which could result in serious personal injury.

21.

Only use the saw blades that are marked with a speed

equal or higher than the speed marked on the tool.

22. Always select the correct saw blade for the

material to be cut. Do not use the saw blade to

cut materials other than those specied.

23. Do not use the saw to cut other than wood,

aluminum or similar materials.

Additional instructions

1. Make workshop kid proof with padlocks.

2. Never stand on the tool. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

3. Never leave the tool running unattended. Turn

the power off. Do not leave tool until it comes

to a complete stop.

4.

Do not operate saw without guards in place. Check

blade guard for proper closing before each use. Do

not operate saw if blade guard does not move freely

and close instantly. Never clamp or tie the blade

guard into the open position.

5. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

6. Never clamp or tie the blade guard into the

open position.

7.

To reduce the risk of injury, return carriage to the

full rear position after each crosscut operation.

8. Always secure all moving portions before

carrying the tool.

9. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

10.

Check the blade carefully for cracks or damage before

operation. Replace cracked or damaged blade immedi-

ately. Gum and wood pitch hardened on blades slows

saw and increases potential for kickback. Keep blade

clean by rst removing it from tool, then cleaning it

with gum and pitch remover, hot water or kerosene.

Never use gasoline to clean blade.

11.

While making a slide cut, KICKBACK can occur.

KICKBACK occurs when the blade binds in the

workpiece during a cutting operation and the saw

blade is driven rapidly towards the operator. Loss

of control and serious personal injury can result. If

blade begins to bind during a cutting operation, do

not continue to cut and release switch immediately.

12. Use only anges specied for this tool.

13.

Be careful not to damage the arbor, anges (espe-

cially the installing surface) or bolt. Damage to

these parts could result in blade breakage.

14. Make sure that the turn base is properly

secured so it will not move during operation.

Use the holes in the base to fasten the saw to a

stable work platform or bench. NEVER use tool

where operator positioning would be awkward.

15. Make sure the shaft lock is released before the

switch is turned on.

16. Be sure that the blade does not contact the

turn base in the lowest position.

17.

Hold the handle rmly. Be aware that the saw moves

up or down slightly during start-up and stopping.

18. Make sure the blade is not contacting the

workpiece before the switch is turned on.

19.

Before using the tool on an actual workpiece, let it run

for a while. Watch for vibration or wobbling that could

indicate poor installation or a poorly balanced blade.

20. Stop operation immediately if you notice any-

thing abnormal.

21. Do not attempt to lock the trigger in the "ON"

position.

22. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

23.

Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

Additional safety rules for the laser

1. LASER RADIATION DO NOT STARE INTO

BEAM.

2. AVOID EXPOSURE - LASER RADIATION IS

EMITTED FROM APERTURE.

3.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

Complies with 21CFR

1040.10 and 1040.11

AVOID EXPOSURE-Laser

radiation is emitted from

LASER RADIATION

this aperture

DO NOT STARE INTO BEAM

Maximum Output

<1mW,Wavelength:655nm

CLASS II LASER PRODUCT

CAUTION

https://tm.by

Интернет-магазин TM.by

6ENGLISH

Symbols

The followings show the symbols used for tool.

volts

amperes

hertz

alternating current

Class II Construction

revolutions or reciprocation per minute

Do not place hand or ngers close to the

blade.

PARTS DESCRIPTION

10 11

12

14

15

3

2

4

5

879

13

6

1

16

17

18

19

20 21

1Slide pole 2Stopper pin (for carriage

sliding)

3Vertical vise 4Releasing button (for

right side bevel angle)

5Holder 6Turn base 7Pointer (for miter angle) 8Miter angle scale

9Kerf board 10 Blade case 11 Adjusting screw (for

laser line)

12 Range adjustment screw

(for laser line)

13 Blade guard 14 Knob (for bevel angle) 15 Hex wrench 16 Adjusting screw (for

lower limit position)

17 Adjusting bolt (for maxi-

mum cutting capacity)

18 Stopper arm 19 Lock lever (for turn base) 20 Releasing lever (for turn

base)

21 Grip (for turn base) ------

https://tm.by

Интернет-магазин TM.by

7ENGLISH

7 8

5

6

1

2

34

9

10

11

141312

15

1Switch trigger 2Lock-off button 3Hole for padlock 4Switch (for laser line)

5Hose (for dust

extraction)

6Stopper pin (for carriage

elevation)

7Guide fence (lower

fence)

8Guide fence (upper

fence)

9Dust bag 10 0° adjusting bolt (for

bevel angle)

11 Bevel angle scale 12 Releasing lever (for 48°

bevel angle)

13 Latch lever (for bevel

angle)

14 Pointer (for bevel angle) 15 45° adjusting bolt (for

bevel angle)

- -

INSTALLATION

Installing the grip

Screw the threaded shaft of the grip into the turn base.

1

2

► 1. Grip 2. Turn base

Installing the dust extraction hose

Connect the dust extraction hose to the tool as illustrated.

Make sure that the elbow and the sleeve t properly to

the ports of the tool.

1

2

3

4

► 1. Dust extraction hose 2. Elbow 3. Sleeve 4. Port

https://tm.by

Интернет-магазин TM.by

8ENGLISH

Bench mounting

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. While lowering the

handle slightly, pull the stopper pin and rotate it 90°.

3

12

► 1. Locked position 2. Unlocked position 3.

Stopper pin

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool's

base. This will help prevent tipping and possible injury.

1

► 1. Bolt

WARNING: Ensure that the tool will not move

on the supporting surface. Movement of the miter

saw on the supporting surface while cutting may

result in loss of control and serious personal injury.

FUNCTIONAL

DESCRIPTION

WARNING: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool. Failure to switch off

and unplug the tool may result in serious personal

injury from accidental start-up.

Blade guard

1

► 1. Blade guard

When lowering the handle, the blade guard rises automat-

ically. The guard is spring loaded so it returns to its original

position when the cut is completed and the handle is raised.

WARNING: Never defeat or remove the blade

guard or the spring which attaches to the guard.

An exposed blade as a result of defeated guarding

may result in serious personal injury during operation.

In the interest of your personal safety, always maintain

the blade guard in good condition. Any irregular opera-

tion of the blade guard should be corrected immediately.

Check to assure spring loaded return action of guard.

WARNING: Never use the tool if the blade

guard or spring are damaged, faulty or removed.

Operation of the tool with a damaged, faulty or

removed guard may result in serious personal injury.

If the see-through blade guard becomes dirty, or sawdust

adheres to it in such a way that the blade and/or workpiece is

no longer easily visible, unplug the saw and clean the guard

carefully with a damp cloth. Do not use solvents or any petro-

leum-based cleaners on the plastic guard because this may

cause damage to the guard.

If the blade guard is especially dirty and vision through

the guard is impaired, unplug the tool and use the sup-

plied wrench to loosen the hex bolt holding the center

cover. Loosen the hex bolt by turning it counterclock-

wise and raise the blade guard and center cover. With

the blade guard so positioned, cleaning can be more

completely and efciently accomplished. When cleaning

is complete, reverse procedure above and secure bolt.

Do not remove spring holding blade guard. If guard

becomes discolored through age or UV light exposure,

contact a Makita service center for a new guard. DO

NOT DEFEAT OR REMOVE GUARD.

https://tm.by

Интернет-магазин TM.by

9ENGLISH

3

1

2

► 1. Center cover 2. Hex wrench 3. Blade guard

Kerf boards

This tool is provided with the kerf boards in the turn base to

minimize tearing on the exit side of a cut. The kerf boards are

factory adjusted so that the saw blade does not contact the

kerf boards. Before use, adjust the kerf boards as follows:

1

► 1. Kerf board

1

23

4

6

5

► 1. Left bevel cut 2. Straight cut 3. Right bevel cut

4. Saw blade 5. Blade teeth 6. Kerf board

First, unplug the tool. Loosen all the screws (2 each on left and right)

securing the kerf boards until the kerf boards can still be easily moved

by hand. Lower the handle fully, then pull and turn the stopper pin to lock

the handle in the lowered position. Release the stopper pin on the sliding

pole and pull the carriage toward you fully. Adjust the kerf boards so that

the kerf boards just contact the sides of the blade teeth. Tighten the front

screws (do not tighten rmly). Push the carriage toward the guide fence

fully and adjust the kerf boards so that the kerf boards just contact the

sides of blade teeth. Tighten the rear screws (do not tighten rmly).

After adjusting the kerf boards, release the stopper pin and

raise the handle. Then tighten all the screws securely.

NOTICE:

After setting the bevel angle ensure that the

kerf boards are adjusted properly. Correct adjustment

of the kerf boards will help provide proper support of the

workpiece minimizing workpiece tear out.

Maintaining maximum cutting capacity

This tool is factory adjusted to provide the maximum

cutting capacity for a 255 mm (10") saw blade.

When installing a new blade, always check the lower limit

position of the blade and if necessary, adjust it as follows:

First, unplug the tool. Turn the stopper lever to engaged position.

1

► 1. Stopper lever

Push the carriage toward the guide fence fully and

lower the handle completely.

Adjust the blade position by turning the adjusting bolt

with the hex wrench. The periphery of the blade should

extend slightly below the top surface of the turn base

and also comes to the point where the front face of the

guide fence meets the top surface of the turn base.

https://tm.by

Интернет-магазин TM.by

10 ENGLISH

1

► 1. Adjusting bolt

1

23

► 1. Top surface of turn base 2. Periphery of blade

3. Guide fence

With the tool unplugged, rotate the blade by hand while holding the

handle all the way down to be sure that the blade does not contact

any part of the lower base. Re-adjust slightly, if necessary.

After adjustment, always return the stopper lever to the

original position.

WARNING:

After installing a new blade and with

the tool unplugged, always be sure that the blade does

not contact any part of the lower base when the handle is

lowered completely. If a blade makes contact with the base it

may cause kickback and result in serious personal injury.

Stopper arm

The lower limit position of the blade can be easily

adjusted with the stopper arm. To adjust it, turn the

stopper arm in the direction of the arrow as shown in the

gure. Turn the adjusting screw so that the blade stops

at the desired position when lowering the handle fully.

1

2

► 1. Stopper arm 2. Adjusting screw

Adjusting the miter angle

CAUTION

:

After changing the miter angle, always

secure the turn base by tightening the grip rmly.

NOTICE: When turning the turn base, be sure to

raise the handle fully.

https://tm.by

Интернет-магазин TM.by

11 ENGLISH

1

2

3

4

► 1. Lock lever 2. Grip 3. Releasing lever 4. Pointer

Rotate the grip counterclockwise to unlock the turn

base. Turn the grip while holding down the lock lever to

move the turn base. Align the pointer with your desired

angle on the scale then tighten the grip.

NOTE: If you depress the releasing lever, you can

move the turn base without holding down the lock

lever. Tighten the grip at your desired position.

This miter saw employs positive stop function. You can

set 0°, 15°, 22.5°, 31.6°, 45°, and 60° right/left miter

angle quickly. To use this function, move the turn base

close to your desired positive stop angle while holding

down the lock lever. Then release the lock lever and

move the turn base forward until the turn base is locked.

Adjusting the bevel angle

NOTICE: Always remove the upper guide fences

and vertical vise before adjusting the bevel angle.

NOTICE: When changing bevel angles, be sure

to position the kerf boards appropriately as

explained in the "Kerf boards" section.

NOTICE: When tilting the saw blade, be sure to

raise the handle fully.

1. Turn the knob on the slide pole counterclockwise.

1

► 1. Knob

2. Pull and turn the latch lever to the position as

illustrated.

1

► 1. Latch lever

3. Match the pointer with your desired angle on the

scale by moving the carriage then tighten the knob.

1

2

► 1. Bevel angle scale 2. Pointer

To tilt the carriage to the right, tilt the carriage to the left slightly and

then tilt it to the right while pressing down the releasing button.

https://tm.by

Интернет-магазин TM.by

12 ENGLISH

1

► 1. Releasing button

If you perform a bevel cut greater than 45°, move the

carriage while sliding the releasing lever toward the

front of the tool. You can perform up to 48° bevel cut.

1

► 1. Releasing lever

This miter saw employs positive stop function. You can

set 22.5° and 33.9° angle to both right and left quickly.

Set the latch lever in the position as illustrated and tilt

the carriage. To change the angle, pull the latch lever

and tilt the carriage.

1

► 1. Latch lever

CAUTION: After changing the bevel angle,

always secure the knob.

Slide lock

To lock the sliding movement of the carriage, push the

carriage toward the guide fence until it stops. Pull the

stopper pin and rotate it 90°.

3

1

2

► 1. Unlocked position 2. Locked position 3. Stopper

Switch action

WARNING:

Before plugging in the tool, always

check to see that the switch trigger actuates properly

and returns to the "OFF" position when released. Do

not pull the switch trigger hard without pressing in

the lock-off button. This can cause switch breakage.

Operating a tool with a switch that does not actuate properly

can lead to loss of control and serious personal injury.

WARNING:

NEVER use tool without a fully oper-

ative switch trigger. Any tool with an inoperative switch is

HIGHLY DANGEROUS and must be repaired before further

usage or serious personal injury may occur.

WARNING: NEVER defeat the lock-off button

by taping down or some other means. A switch with

a negated lock-off button may result in unintentional

operation and serious personal injury.

WARNING:

NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the lock-off

button. A switch in need of repair may result in unintentional

operation and serious personal injury. Return tool to a Makita

service center for proper repairs BEFORE further usage.

1

2

3

► 1. Switch trigger 2. Lock-off button 3. Hole for

padlock

https://tm.by

Интернет-магазин TM.by

13 ENGLISH

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

A hole is provided in the switch trigger for insertion of a

padlock to lock the tool off.

WARNING: Do not use a lock with a shank or

cable any smaller than 6.35 mm (1/4") in diameter.

A smaller shank or cable may not properly lock the

tool in the off position and unintentional operation

may occur resulting in serious personal injury.

Electric brake

This tool is equipped with an electric blade brake. If the tool

consistently fails to quickly stop the blade after the switch trigger

is released, have the tool serviced at a Makita service center.

CAUTION: The blade brake system is not a

substitute for the blade guard. Never use tool

without a functioning blade guard. An unguarded

blade may result in serious personal injury.

Electronic function

Constant speed control

The tool is provided with an electronic speed control

which helps maintain a constant blade rotation speed

even under load. A constant blade rotation speed will

result in a very smooth cut.

Soft start feature

This function allows the smooth start-up of the tool by

limiting the start-up torque.

Laser beam action

For model LS1019L only

CAUTION: Never look into the laser beam.

Direct laser beam may injure your eyes.

To turn on the laser beam, press the upper position (I)

of the switch. To turn off the laser beam, press the lower

position (0) of the switch

1

► 1. Switch for laser

Laser line can be shifted to either the left or right side of

the saw blade by turning the adjusting screw as follows.

1

► 1. Adjusting screw

1. Loosen the adjusting screw by turning it

counterclockwise.

2. With the adjusting screw loosened, slide the

adjusting screw to the right or left as far as it goes.

3. Tighten the adjusting screw rmly at the position

where it stops sliding.

NOTE: Laser line is factory adjusted so that it is

positioned within 1 mm (0.04") from the side surface

of the blade (cutting position).

NOTE: When laser line appears dim and hard to see

because of direct sunlight, relocate the work area to a

place where there is less direct sunlight.

Aligning the laser line

Align the cutting line on your workpiece with the laser line.

A

B

A) When you want to obtain the correct size on the left

side of workpiece, shift the laser line to the left of the

blade.

B) When you want to obtain the correct size on the right

side of workpiece, shift the laser line to the right of the

blade.

NOTE: Use wood facing against the guide fence

when aligning the cutting line with the laser line at the

side of guide fence in compound cutting (bevel angle

45° and miter angle right 45°).

https://tm.by

Интернет-магазин TM.by

14 ENGLISH

ASSEMBLY

WARNING: Always be sure that the tool is

switched off and unplugged before working on

the tool. Failure to switch off and unplug the tool may

result in serious personal injury.

Hex wrench storage

When not in use, store the hex wrench as shown in the

gure to keep it from being lost.

1

► 1. Hex wrench

Removing and installing saw blade

WARNING: Always be sure that the tool is

switched off and unplugged before installing or

removing the blade. Accidental start up of the tool

may result in serious personal injury.

WARNING: Use only the Makita wrench pro-

vided to install or remove the blade. Failure to use

the wrench may result in overtightening or insufcient

tightening of the hex socket bolt and serious personal

injury.

Always lock the carriage with raised position when

removing and installing the blade. Pull the stopper pin

and rotate it 90° with the carriage raised.

12

3

► 1. Unlocked position 2. Locked position 3. Stopper

Removing the blade

Loosen the hex bolt holding the center cover using the

hex wrench. Raise the blade guard and center cover.

3

1

2

► 1. Center cover 2. Hex wrench 3. Blade guard

Press the shaft lock to lock the spindle and use the hex

wrench to loosen the hex socket bolt. Then remove the

hex socket bolt, outer ange and blade.

https://tm.by

Интернет-магазин TM.by

15 ENGLISH

1

2

4

5

3

► 1. Shaft lock 2. Hex wrench 3. Hex socket bolt (left-

handed) 4. Loosen 5. Tighten

Installing the blade

Mount the blade carefully onto the spindle, making

sure that the direction of the arrow on the surface of the

blade matches the direction of the arrow on the blade

case.

1

2

► 1. Arrow on the blade case 2. Arrow on the blade

Install the outer ange and hex socket bolt. Tighten the

hex socket bolt counterclockwise using the hex wrench

while pressing the shaft lock.

1 2 34 5

► 1. Hex socket bolt 2. Outer ange 3. Saw blade

4. Inner ange 5. Spindle

NOTICE: If the inner ange is removed, be sure to

install it on the spindle with its protrusion facing away

from the blade. If the ange is installed incorrectly, the

ange will rub against the machine.

Return the blade guard and center cover to its original

position. Then tighten the hex bolt clockwise to secure

the center cover. Unlock the stopper pin to release

carriage from the raised position. Lower the handle to

make sure that the blade guard moves properly. Make

sure shaft lock has released spindle before making cut.

Connecting a vacuum cleaner

When you wish to perform clean cutting operation, con-

nect a Makita vacuum cleaner to the dust nozzle using

a front cuffs 24 (optional accessory).

1 2

3

► 1. Front cuffs 24 2. Hose 3. Vacuum cleaner

https://tm.by

Интернет-магазин TM.by

16 ENGLISH

Dust bag

The use of the dust bag makes cutting operations clean

and dust collection easy. To attach the dust bag, remove

the dust extraction hose on the tool and connect the

dust bag.

1

2

► 1. Dust extraction hose 2. Dust bag

When the dust bag is about half full, remove the dust

bag from the tool and pull the fastener out. Empty

the dust bag of its contents, tapping it lightly so as to

remove particles adhering to the insides which might

hamper further collection.

1

► 1. Fastener

Securing workpiece

WARNING: It is extremely important to always

secure the workpiece correctly with the proper

type of vise or crown molding stoppers. Failure to

do so may result in serious personal injury and cause

damage to the tool and/or the workpiece.

WARNING: After a cutting operation do not

raise the blade until it has come to a complete

stop. The raising of a coasting blade may result in

serious personal injury and damage to the workpiece.

WARNING: When cutting a workpiece that

is longer than the support base of the saw, the

material should be supported the entire length

beyond the support base and at the same height

to keep the material level. Proper workpiece support

will help avoid blade pinch and possible kickback

which may result in serious personal injury. Do not

rely solely on the vertical vise and/or horizontal vise

to secure the workpiece. Thin material tends to sag.

Support workpiece over its entire length to avoid

blade pinch and possible KICKBACK.

12

► 1. Support 2. Turn base

Guide fences

WARNING: Before operating the tool, make

sure that the upper fence is secured rmly.

WARNING: Before bevel-cutting, make sure

that no part of the tool, especially the blade, con-

tacts the upper and lower fences when fully low-

ering and raising the handle in any position and

while moving the carriage through its full range

of travel. If the tool or blade makes contact with

the fence this may result in kickback or unexpected

movement of the material and serious personal injury.

Use upper fences to support the material higher than

the lower fences. Insert the upper fence into the hole on

the lower fence and tighten the clamping screw.

https://tm.by

Интернет-магазин TM.by

17 ENGLISH

1

2

3

1

2

3

4

► 1. Upper fence 2. Lower fence 3. Clamping screw

4. Adjusting screw

NOTICE: The lower fences are xed to the base in

the factory. Do not remove the lower fences.

NOTICE: If the upper fence is still loose after tight-

ening the clamping screw, turn the adjusting screw to

close a gap. The adjusting screw is factory adjusted.

You don't need to use it unless needed.

You can store the upper fences onto the holder when

not in use. Use the clip on the upper fence to hold it on

the holder.

1 2

3

► 1. Holder 2. Upper fence 3. Clip

Vertical vise

WARNING: The workpiece must be secured

rmly against the turn base and guide fence with

the vise during all operations. If the workpiece is

not properly secured against the fence the material

may move during the cutting operation causing

possible damage to the blade, causing the material

to be thrown and loss of control resulting in serious

personal injury.

1

2

3

4

► 1. Vise arm 2. Vise rod 3. Clamping screw 4. Vise

knob

The vertical vise can be installed in two positions on either the left or

right side of the base. Insert the vise rod into the hole in the base.

Position the vise arm according to the thickness and shape of the

workpiece and secure the vise arm by tightening the screw. If the

clamping screw contacts the carriage, install it on the opposite side

of vise arm. Make sure that no part of the tool contacts the vise when

lowering the handle all the way. If some part contacts the vise, re-po-

sition the vise.

Press the workpiece at against the guide fence and the turn base.

Position the workpiece at the desired cutting position and secure it

rmly by tightening the vise knob.

NOTE: For a quick setting of workpiece, turning the

vise knob to 90° counterclockwise allows the vise

knob to be moved up and down. To secure the work-

piece after setting, turn the vise knob clockwise.

Horizontal vise

Optional accessory

WARNING:

Always rotate the vise nut clockwise

until the workpiece is properly secured. If the workpiece

is not properly secured the material may move during the

cutting operation causing possible damage to the blade,

causing the material to be thrown and loss of control result-

ing in serious personal injury.

WARNING: When cutting a thin workpiece,

such as base boards, against the fence, always

use the horizontal vise.

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

22.5° or greater miter cuts, install the horizontal vise on

the side opposite the direction in which the turn base is

to be turned.

https://tm.by

Интернет-магазин TM.by

18 ENGLISH

1

2 3

► 1. Vise plate 2. Vise nut 3. Vise knob

By ipping the vise nut counterclockwise, the vise is

released, and rapidly moves in and out. To grip the

workpiece, push the vise knob forward until the vise

plate contacts the workpiece and ip the vise nut clock-

wise. Then turn the vise knob clockwise to secure the

workpiece.

NOTE: The maximum width of workpiece which can

be secured by the horizontal vise is 228 mm (9″).

Holders

WARNING: Always support a long workpiece

so it is level with the top surface of the turn base

for an accurate cut and to prevent dangerous loss

of tool control. Proper workpiece support will help

avoid blade pinch and possible kickback which may

result in serious personal injury.

To hold long workpieces horizontally, holders are pro-

vided on both sides of the tool. Loosen the screws and

extend the holders to the appropriate length for holding

the workpiece. Then tighten the screws.

1

2

► 1. Holder 2. Screw

OPERATION

WARNING:

Make sure the blade is not contacting

the workpiece, etc. before the switch is turned on.

Turning the tool on with the blade in contact with the work-

piece may result in kickback and serious personal injury.

WARNING: After a cutting operation, do not

raise the blade until it has come to a complete

stop. The raising of a coasting blade may result in

serious personal injury and damage to the workpiece.

WARNING: Do not perform any adjustment

such as turning grip, knob, and levers on the tool

while the blade is rotating. Adjustment while the

blade is rotating may result in serious personal injury.

NOTICE:

Before use, be sure to unlock the stopper

pin and release the handle from the lowered position.

NOTICE:

Do not apply excessive pressure on the han-

dle when cutting. Too much force may result in overload of the

motor and/or decreased cutting efciency. Press down handle

with only as much force as necessary for smooth cutting and

without signicant decrease in blade speed.

NOTICE: Gently press down the handle to per-

form the cut. If the handle is pressed down with force

or if lateral force is applied, the blade may vibrate and

leave a mark (saw mark) in the workpiece and the

precision of the cut may be impaired.

NOTICE:

During a slide cut, gently push the carriage

toward the guide fence without stopping. If the carriage

movement is stopped during the cut, a mark will be left in

the workpiece and the precision of the cut will be impaired.

Press cutting

WARNING: Always lock the sliding movement

of the carriage when performing a press cutting.

Cutting without lock may cause possible kickback

which may result in serious personal injury.

Workpieces up to 71 mm (2-13/16") high and 155 mm

(6-1/8") wide can be cut in the following manner.

1

► 1. Stopper pin

https://tm.by

Интернет-магазин TM.by

19 ENGLISH

1. Push the carriage toward the guide fence until it

stops and lock it with the stopper pin.

2. Secure the workpiece with the proper type of vise.

3. Switch on the tool without the blade making any

contact and wait until the blade attains full speed before

lowering.

4. Gently lower the handle to the fully lowered posi-

tion to cut the workpiece.

5. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Slide (push) cutting (cutting wide

workpieces)

WARNING: Whenever performing a slide cut,

rst pull the carriage full towards you and press

the handle all the way down, then push the car-

riage toward the guide fence. Never start the cut

with the carriage not pulled fully toward you. If

you perform the slide cut without the carriage pulled

fully toward you unexpected kickback may occur and

serious personal injury may result.

WARNING: Never attempt to perform a slide

cut by pulling the carriage towards you. Pulling

the carriage towards you while cutting may cause

unexpected kickback resulting in possible serious

personal injury.

WARNING: Never perform the slide cut with

the handle locked in the lowered position.

1

► 1. Stopper pin

1. Unlock the stopper pin so that the carriage can

slide freely.

2. Secure the workpiece with the proper type of vise.

3. Pull the carriage toward you fully.

4. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

5. Press the handle down and push the carriage

toward the guide fence and through the workpiece.

6. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Miter cutting

Refer to the previously covered "Adjusting the miter angle".

Bevel cut

WARNING:

After setting the blade for a bevel cut,

ensure that the carriage and blade will have free travel

throughout the entire range of the intended cut before

operating the tool. Interruption of the carriage or blade

travel during the cutting operation may result in kickback

and serious personal injury.

WARNING: While making a bevel cut keep

hands out of the path of the blade. The angle of the

blade may confuse the operator as to the actual blade

path while cutting and contact with the blade will

result in serious personal injury

WARNING:

The blade should not be raised until

it has come to a complete stop. During a bevel cut the

piece cut off may come to rest against the blade. If the

blade is raised while it is rotating the cut-off piece maybe

ejected by the blade causing the material to fragment which

may result in serious personal injury.

NOTICE: When pressing down the handle, apply

pressure in parallel with the blade. If a force is

applied perpendicularly to the turn base or if the pres-

sure direction is changed during a cut, the precision

of the cut will be impaired.

1. Remove the upper fence on the side that you are

going to tilt the carriage.

2. Unlock the stopper pin.

3. Adjust the bevel angle according to the procedure

explained in the "Adjusting the bevel angle" section.

https://tm.by

Интернет-магазин TM.by

20 ENGLISH

Then tighten the knob.

4. Secure the workpiece with a vise.

5. Pull the carriage toward you fully.

6. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

7. Gently lower the handle to the fully lowered posi-

tion while applying pressure in parallel with the blade

and push the carriage toward the guide fence to cut

the workpiece.

8. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at the angle shown in the table.

Miter angle Bevel angle

Left and Right 0° - 45° Left and Right 0° - 45°

When performing compound cutting, refer to "Press cutting",

"Slide (push) cutting", "Miter cutting" and "Bevel cut" explanations

Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound miter

saw with the moldings laid at on the turn base.

There are two common types of crown moldings and one type

of cove moldings; 52/38° wall angle crown molding, 45° wall

angle crown molding and 45° wall angle cove molding.

123

► 1. 52/38° type crown molding 2. 45° type crown

molding 3. 45° type cove molding

There are crown and cove molding joints which are

made to t "Inside" 90° corners ((a) and (b) in the gure)

and "Outside" 90° corners ((c) and (d) in the gure.)

(a) (b) (c) (d)

12

1. Inside corner 2. Outside corner

2

(a)

(b)

(a)

(b) (b)

(a)

(b)

(a)

(b)

(c)(d)

1

1. Inside corner 2. Outside corner

Measuring

Measure the wall width, and adjust the width of the

workpiece according to it. Always make sure that width

of the workpiece's wall contact edge is the same as wall

length.

2

31

4

► 1. Workpiece 2. Wall width 3. Width of the work-

piece 4. Wall contact edge

Always use several pieces for test cuts to check the

saw angles.

When cutting crown and cove moldings, set the bevel

angle and miter angle as indicated in the table (A) and

position the moldings on the top surface of the saw

base as indicated in the table (B).

https://tm.by

Интернет-магазин TM.by

La page charge ...

Makita LS1019 Slide Compound Miter Saw Manuel utilisateur

Makita LS1019 Slide Compound Miter Saw Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents