Sensitech LTE CAT-M-2G Manuel utilisateur

LTE CAT-M-2G
Marque
Sensitech
Modèle
LTE CAT-M-2G
Taper
Manuel utilisateur
USER MANUAL
For
LTE CAT-M/2G Temperature Tracker, Non-Lithium
LTE CAT-M/2G Air Temperature Tracker, Non-Lithium
LTE CAT-M/2G Air Probe Temperature Tracker, Non-Lithium
LTE CAT-M/2G Air Probe Temperature Tracker, Extended
LTE CAT-M/2G Temperature Tracker, Extended
LTE CAT-M/2G Air Temperature Tracker, Extended
NOTICE OF PROPRIETARY PROPERTY
This document and the information contained in it are the proprietary property of Sensitech. It may not be copied or used
in any manner nor may any of the information in or upon it be used for any purpose without the express written consent of
an authorized agent of Sensitech Inc.
REVISION HISTORY:
REV
DESCRIPTION
DWN
APVD
DATE
3
Initial Release
JZL
28SEPT20
3.1
Revise Product description
TP
25NOV20
3.2
Updated the FCC and IC statements
TP
23DEC20
3.3
Updated the FCC and IC RF exposure statements
TP
29DEC20
© SENSITECH INC. Page 3 of 10
T11012820 User Manual
Table of Contents
1. Introduction .................................................................................................................. 4
1.1. Purpose ............................................................................................................ 4
1.2. Scope ................................................................................................................ 4
1.3. Description ........................................................................................................ 4
1.4. Radio Frequency Characteristics ...................................................................... 5
1.4.1. Operating Frequencies .................................................................... 5
1.4.2. TRP/TIS ........................................................................................... 5
2. Physical Appearance ................................................................................................... 6
2.1. User Interface ................................................................................................... 6
2.1.1. LEDs................................................................................................ 6
2.1.2. Buttons ............................................................................................ 6
3. Using the Device ......................................................................................................... 7
3.1. Starting the device: ........................................................................................... 7
3.2. Stopping the device: ......................................................................................... 7
3.3. Status Check the device: .................................................................................. 7
3.3.1. Status LED Indicators ...................................................................... 7
4. Software ...................................................................................................................... 8
5. Disclaimers .................................................................................................................. 9
5.1. FCC- pending ................................................................................................... 9
5.2. IC- pending ..................................................................................................... 10
5.3. CE – pending .................................................................................................. 10
5.4. Brazil - pending ............................................................................................... 10
5.5. NOM - pending................................................................................................ 10
© SENSITECH INC. Page 4 of 10
T11012860 User Manual
1. Introduction
1.1. Purpose
This document describes the usage of a TEMPTALE GEO/VIZCOMM VIEW- LTE/LTE
EXTENDED, ULTRA/ ULTRA EXTENDED, ULTRA DRY ICE/ ULTRA DRY ICE EXTENDED
device.
1.2. Scope
The intended audience is a valued customer.
1.3. Description
LTE CAT-M/2G Air Probe Temperature Tracker, Extended/LTE CAT-M/2G Temperature
Tracker, Extended/LTE CAT-M/2G Air Temperature Tracker, Extend is a LTE-M/2G GSM
Quad band tracking device, and sensor data logger designed for the transportation industry.
It is primarily intended to be used as a real time position-monitoring device, which will also
produce accurate temperature and humidity. Specific variants of the device also uses various
sensors to detect when the aircraft has taken off and when it has landed to disable/enable the
cellular modem.
The following is a brief summary of its features:
1. LTE-M/2G GSM Quad Band
2. Internal battery
3. Accelerometer (optional)
4. Temperature Sensor
5. Humidity Sensor
6. Light Sensor
7. Pressure Sensor (optional)
8. NFC for secondary download (optional)
9. Dry Ice Probe (optional)
10. User Interface
Manufacturer Information
Company Name: SENSITECH Inc.
Address: 800 Cummings Center, Beverly, MA USA
Importer Information : PENDING
Company Name: XXXXXXXXXX
Address: XXXXXXXXXXXXX
© SENSITECH INC. Page 5 of 10
T11012860 User Manual
1.4. Radio Frequency Characteristics
1.4.1. Operating Frequencies
LTE-FDD: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28
LTE-TDD: B39 (for LTE CAT-M only)
GSM: GSM850/900/1800/1900
CE: Bands 46A/47/48/50/54/56B
NFC: 13.56MHZ (only used for secondary download of sensor data)
1.4.2. TRP/TIS
Cellular Maximum Conducted TRP: TBD
Cellular Minimum Conducted TIS: TBD
© SENSITECH INC. Page 6 of 10
T11012860 User Manual
2. Physical Appearance
2.1. User Interface
The user interface consists of the following:
1. Six LEDs (2 sets of red, green, blue)
2. Two buttons(Start/Status)
2.1.1. LEDs
The LEDs are intended to allow quick and easy-to-read status to be conveyed to the
end user. The user can immediately know the status of the unit during startup and
operation.
2.1.1.1. System Startup Sequence
During startup, the Blue LED will blink rapidly.
Once it has completed its startup tests, the LED will indicate the
following:
Red
Green
Blue
2.1.2. Buttons
There are two buttons on the device:
1. Start/Stop – a configurable press delay is added, usually configured to be
held for three second before it starts.
2. Status– a configurable press delay is added usually configured to be held for
three seconds before it conducts a status check.
© SENSITECH INC. Page 7 of 10
T11012860 User Manual
3. Using the Device
3.1. Starting the device:
To start the device, press the START button. If the Start Key feature is enabled, the START
button must be held down for 3 seconds. The device may only be started from sleep mode.
3.2. Stopping the device:
To stop the device, press the START button. If the Stop Key feature is enabled, the START
button must be held down for 5 seconds to stop.
3.3. Status Check the device:
To check the status of the device, press the STATUS button. The STATUS button will
indicate the device mode with a unique LED blink pattern. See table below.
3.3.1. Status LED Indicators
16
Un-configured mode, Not Started
4
Customer Ready Mode, Not Started
2
Running, Started
1
Stopped, Not Started
© SENSITECH INC. Page 8 of 10
T11012860 User Manual
4. Software
This unit reports data over the cellular network. This data is accessible via several web-based
platforms that target various industries. Please contact customer support for more information.
© SENSITECH INC. Page 9 of 10
T11012860 User Manual
5. Disclaimers
Risk of Fire Hazard if battery is not charged in accordance with manufacturer’s instruction.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Do not dispose battery along with household waste.
There are no user serviceable parts inside, battery cannot be replaced by the end user, and will
result in damaging device.
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
5.1. FCC- pending
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
© SENSITECH INC. Page 10 of 10
T11012860 User Manual
15.19
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause undesired
operation of the device.
5.2. IC- pending
Canadian Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Avis Canadien
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
5.3. CE – pending
Hereby, Sensitech declares that the radio equipment type LTE CAT-M/2G GSM/GPRS
Tracking Device is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available upon request.
5.4. Brazil - pending
"Este equipamento não tem direito à proteção contra interferência prejudicial e não pode
causar interferência em sistemas devidamente autorizados"
Anatel ID: TBD
Modem: Quectel BG-96
5.5. NOM - pending
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que
este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo
debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no
deseada.
Número IFETEL: TBD
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Sensitech LTE CAT-M-2G Manuel utilisateur

LTE CAT-M-2G
Marque
Sensitech
Modèle
LTE CAT-M-2G
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents