EcoFlow EFM100 Manuel utilisateur

Taper
Manuel utilisateur
POWER HUB
EFM100-HUB-HV
User Manual V1.0
EN
Disclaimer
Read this user manual carefully before using the product to ensure that you
completely understand the product and can correctly use it. After reading this user
manual, keep it properly for future reference. Improper use of this product may cause
serious injury to yourself or others, or cause product damage and property loss. Once
you use this product, it is deemed that you understand, approve and accept all the
terms and content in this document. EcoFlow is not liable for any loss caused by the
user's failure to use this product in compliance with this user manual.
In compliance with laws and regulations, EcoFlow reserves the right to nal
interpretation of this document and all documents related to this product. This
document is subject to changes (updates, revisions, or termination) without prior
notice. Please visit EcoFlow's ocial website to obtain the latest product information.
EN
Table Of Contents
Technical Specications
Safety Instructions
EcoFlow App
Getting Started
Product Usage
FAQs
What's in the Box
Care and Maintenance
FCC Statement
System Overview
Product Overview
CAN Bus Connection
Power On/O
DC Output
AC Output
AC Charging
Smart Generator Charging
Solar Charging
Vehicle Alternator Charging
1
2
3
3
3
5
6
8
8
8
9
9
10
10
10
11
12
12
13
13
14
15
15
X-Boost Feature
Bypass Mode
Inverter Mode
Standby Mode
EN
1
Technical Specications
Basic Information
Net Weight 14 kg (31 lbs)
Dimensions (L × W × H) 48 cm × 14 cm × 30 cm (18.9“ x 5.5” x 11.8“)
Wi-Fi Supported (<120 Meters)
Bluetooth (v4.0) Supported (<15 Meters)
Output Spec
Pure sine wave, 3600 W (surge 7200 W, 100 ms),
230 V, 50 Hz (Australian Version: 240 V, 50 Hz)
Linear derating to 1800 W when 40℃ (104°F) < Ambient
Temperature < 60℃ (140°F)
Derating to 3000 W when battery voltage < 49 V
Maximum AC Output
Supported by X-Boost
13.6 V 70 A, maximum power: 1000 W
or 26.4 V 60 A, maximum power: 1600 W
Input Spec
3000 W maximum power, 15 A maximum current,
supported by EcoFlow X-Stream Technology
AC Input Voltage 220–240 V, 50 Hz/60 Hz
PV Input 2/3 15–60 V 30 A, maximum power: 1600 W
Alternator Input
PV Input 1
13–60 V 60 A, maximum power: 1000 W
15–60 V 30 A, maximum power: 1600 W
Battery Port Spec
40-60 V 100 A, supports up to three 2kWh or 5kWh LFP
batteries, which are sold separately.(Not recommended to
use one Power Hub with both a 2kWhLFP and 5kWh battery
at the same time.)
Operating Environment
Operating Temperature –25°C to 60°C (-13°F to 140°F)
Storage Temperature –25°C to 60°C (-13°F to 140°F)
Other
EcoFlow Smart Generator 1800 W maximum charging power, sold separately.
AC Output
DC Output
5200 W
Battery Port (x3)
AC Input Power
EN
2
Safety Instructions
1. SAVE THESE INSTRUCTIONS – This manual contains important safety and operating
instructions
2. Before using battery charger function, read all instructions and cautionary markings on
battery charger, battery, and product using battery.
3. CAUTION – To reduce risk of injury, charge only LiFePO4 type rechargeable batteries.
Other types of batteries may burst causing personal injury and damage.
4. This is a Safety Class I product (supplied with a protective grounding terminal).
Uninterruptible protective grounding must be provided at the AC input and/or output
terminals. Alternatively, the grounding point located externally on the product may
be used. Whenever it is likely that the grounding protection has been damaged, the
product must be turned o and secured against unintended operation; please contact
qualied service sta.
5. To prevent re, short circuits, and electric shocks, do not install this product in
environments with high humidity, high temperature, or conductive contaminants.
6.
Before installing this product, disconnect the main power supply. Do not work with live power.
7. Keep this product away from heat sources, such as res or heating furnaces.
8. Keep this product away from any liquid. Do not immerse this product in water or get it
wet. Do not use this product in rain or humid environments.
9. Do not use this product in environments with strong static electricity or magnetic elds.
10. Do not disassemble this product in any way or pierce it with sharp objects.
11. Do not use wires or other metal objects that may result in a short circuit.
12. Do not use unocial components or accessories. If components or accessories need
to be replaced, purchase them from the EcoFlow ocial sales channels.
13. Strictly comply with the ambient temperature for use in this user manual when using
this product.
14. Do not stack other heavy objects on this product.
15. Do not forcibly block the fan during product use or place the product in an unventilated
or dusty area.
16. Please avoid impact, falls, or severe vibrations when using the product. In case of a
severe external impact, turn o the power supply immediately and stop using the
product. Ensure the product is well fastened during transportation to avoid vibrations
and impacts.
17. If the product falls into water accidentally during use, place it in a safe open area and
stay away from it until it is completely dry. The dried product cannot be reused, and
should be properly disposed according to the method described in the EcoFlow
Battery User Manual. If the product catches re, we recommend that you use the
re extinguishers in the following order: water or water mist, sand, re blanket, dry
powder , and carbon dioxide re extinguisher.
18. If there is dirt on the ports of the product, clean it with a dry cloth.
19. Place this product carefully to prevent damage caused by the product falling over. If
the product falls over and is seriously damaged, power it o immediately.
20. Keep this product out of reach of children and pets.
EN
3
Control, monitor and customize your Power Kits from afar with the
EcoFlow App. Download at:
https://download.ecoow.com/app
Privacy Policy
By using EcoFlow Products, Applications and Services, you consent to the EcoFlow Term
of Use and Privacy Policy, which you can access via the “About” section of the “User” page
on the EcoFlow App or on the ocial EcoFlow website at https://www.ecoow.com/policy/
terms-of-use and https://www.ecoow.com/policy/privacy-policy
Getting Started
EcoFlow App
System Overview
1. If the product is installed in an enclosed space, proper ventilation is a MUST
to prevent this product from overheating.
2. For safety reasons, it is recommended to install a Ground Fault Circuit
Interrupter (GFCI), also known as Residual Current Device (RCD) in the
AC input and AC output of the Power Hub. Please
refer to local regulations
regarding grounding of autonomous power systems.
3. Before connecting this product to EcoFlow LFP Battery, ensure that there is
no charging input connected to Power Hub and LFP Battery is powered o.
4.
It is not recommended to use one Power Hub with both 2kWh and 5kWh LFP
battery at the same time.
5. It is not recommended to connect or disconnect LFP battery when the
system is on.
Bluetooth of this product can only be connected with one EcoFlow App
account, if you need to connect the product through another account, you can
reset the Bluetooth through the App or by long pressing the DC button of the
product for 3 seconds.
EN
4
DC Appliance
AC Appliance
O-grid Builds DC Appliance
AC Appliance
4
4
4
2. AC/DC Smart Distribution Panel
6. Shore Power/Grid Power
9. Vehicle Alternator
1. EcoFlow Power Hub
3. Power Kit Console
4.
EcoFlow 2kWh/5kWh LFP Battery
5. EcoFlow Smart Generator
7. Rigid/Flexible Solar Panel
8. Foldable / Portable Solar Panel
8
1
3
4
9
45
6
7
Vehicles
2
EN
5
Product Overview
1. ALT IN / PV IN 1 Port
2. PV IN 2/3 Port
3. Battery 1/2/3 Port /
Smart Generator Port
4. AC IN Port
5. AC OUT Port (10A)
(British Version /
European Version /
Australian Version)
6. Main Power Button
7. DC OUT Button
8. AC OUT Button
9. AC Out Indicator
10. DC Out Indicator
11. AC IN Indicator
12. PV IN 2/3 Indicator
13. ALT IN / PV IN 1 Indicator
14. RJ45 CAN Bus Ports
15. DC Main OUT Port
16. AC Main OUT Port
17. Earth Stud
18. Air Outlet
19. Air Inlet
18
19
6
7
8
9
101113
14
12
15
16
17
14
32 5
EN
6
CAN Bus Connection
To ensure better communication quality, this product comes with two RJ45 CAN
Bus ports, each port can be connected to AC/DC Smart Distribution Panel, Power
Kit Console, or RJ45 CAN bus terminator. Both ports must be connected to stabilize
communication throughout the system. Not doing so will cause the system to
malfunction.
1. When neither the AC/DC Smart distribution Panel nor the Power Kit Console is connected,
two RJ45 CAN Bus terminators must be connected to the Power Hub.
3. When either the AC/DC Smart Distribution Panel or the Control Panel is connected,
one
CAN Bus RJ45 terminator must be connected to the Power Hub.
2. The AC/DC Smart Distribution Panel and the Power Kit Console are connected to the
Power Hub.
1
2
3
EN
7
Power On / O
DC Output
3s
1. Please wait 5 seconds to let the system completely shut down before further
operation after pressing the main power button.
2. Ensure that there is no charging input connected to the Power Hub before
shutting down the Power Kits.
When the power is on, short press the DC button to enable DC Output. To disable DC
Output, short press the DC button.
Product Usage
DC OUT: White
light stays on
Error: Orange
light ashing
Status Indicators (Top right corner)
Five indicators light up from left to right,
ash 3 times and stay o.
Power-o Five indicators ash 3 times and stay o. O
Power-on On
Main Power Indicator
EN
8
AC OUT: White
light stays on
Error: Orange
light ashing
AC Output
When the power is on, short press the AC button to enable AC Output. To disable AC Output,
short press the AC button again.
When Power Hub is in idle mode, please turn o AC Output to avoid power loss.
AC Charging
The EcoFlow Power Hub features EcoFlow fast charging technology X-Stream . The
maximum AC charging power is 3000 W and the maximum AC charging current is 15 A.
User can adjust the charging current via EcoFlow App or Power Kit Console. The default
charging current is 10 A.
Charging: White light ashing
Fully charged: White light stays on
Error: Orange light ashing
EcoFlow is not liable for damages caused by the use of charging cables not
provided by EcoFlow.
EN
9
Smart Generator Charging
The Power Kits can be recharged by connecting EcoFlow Smart Generator as shown
below.
DC Charging
Connect EcoFlow Smart Generator to the Power Hub with the Smart Generator Charging
Cable (Smart Generator and charging cable are sold separately).
AC Charging
Connect EcoFlow Smart Generator to the Power Hub with the AC Charging Cable.
EN
10
Solar Charging
The Power Hub has three PV (Photovoltaic) input ports, with a total power of 4800 W for
the three ports and 1600 W for each port, PV2/3 ports are dedicated PV input ports, PV1
can be connected to a vehicle alternator for charging or be used as a PV input port. The
maximum input current is 30 A each.
PV1 Port
PV2 Port
PV3 Port
Charging: White light ashing
Fully charged: White light stays on
Error: Orange light ashing
EN
11
Vehicle Alternator Charging
Users can connect the ALT IN / PV IN 1 Port of the Power Hub and the chassis battery of
the vehicle through the alternator charging cable provided by EcoFlow. The Power Hub
accepts both 12 V and 24 V alternators, and the maximum charging power is 1000 W. The
maximum charging current is 60 A, and the default charging current is 30 A. Users can
adjust the charging current via EcoFlow App or Power Kit Console.
It is strongly recommended to unplug the alternator charging cable from the Power
Hub when vehicle is not in use for a long time.
X-Boost Feature
1. The X-Boost feature is unavailable when AC Output is in bypass mode.
2. The X-Boost feature is not suitable for all appliances. The X-Boost feature is
only suitable for heating appliances. It is not suitable for some appliances with
voltage protection, such as precision instruments.
With EcoFlow X-Boost technology, this product can power a 5200 W Max device (for
heating appliances only) while the rated output power remains 3600 W, avoiding
operation failure due to overload protection.
Error : Orange light ashing
Charging : White light ashing
Fully charged : White light stays still
EN
12
When external AC power source is not available, the system will enter Inverter Mode. AC
Output is now supplied by the LFP battery.
Inverter Mode
Bypass Mode
When the product is connected to external AC and the AC output is enabled, the system
enters bypass mode. The AC output is provided by the external AC power supply and the
LFP battery is charged by the external AC power supply.
AC DC
DC
DC
DC
PV1
PV2
PV3
DC
DC DC
DC DC
AC IN AC OUT
DC OUT
BATTERIES
AC DC
DC
DC
DC
PV1
PV2
PV3
DC
DC DC
DC DC
AC IN AC OUT
DC OUT
BATTERIES
EN
13
FAQs
1. Can I connect non-ECOFLOW photovoltaic panels?
Yes, the Power hub has three independent PV charging inputs, and users are free to
choose any brand and model of PV panel.
2. Which scenarios does this product apply to?
Application scenarios include but are not limited to Homes, RVs, and O-grid Builds.
3. Do the input and output parameters of this product apply to electricity use
standards of all countries?
Yes. Both low-voltage and high-voltage versions of this product are available, which
cover electricity use standards of all countries.
4. What are the charging and discharging methods of this product?
Charging methods include: AC Charging, Vehicle Alternator Charging, Smart Generator
Charging and Solar Charging. The discharging method is AC/DC output.
5. Which devices can connect to the AC output port of this product?
The rated power of the AC output port of this product is 3600W, and surge power is
7200W. It can supply power to most home appliances. However, it is recommended to
conrm the power of the appliances before use, and ensure that the total power of all
AC loads is less than the rated power.
6. How can I clean this product?
Use a dry, soft, and clean cloth or paper towel to wipe o dust, dirt, or water on this
product.
7. How do I store this product?
Before storage, power o the product, then store it in a dry and well-ventilated indoor
environment. Do not place this product near water sources.
When DC OUT and AC OUT have no continuous output for 20 seconds, the Power Hub will
enter Standby Mode automatically to reduce power consumption and save battery energy.
Press the DC OUT or AC OUT button to wake up the system.
The Power Hub will not enter Standby Mode during rmware update.
Standby Mode
EN
14
What's in the Box
Mounting Kit (Back)×1
M5*20 (7pcs)
M4*10 (6pcs) User Manual ×1
Warranty Card ×1
Quick Start Guide ×1
Mounting Kit (Bottom)×1 RJ-45 CAN Bus
Terminator ×2
Solar Charge Cable
(6m/20ft) ×1
Power Hub ×1
EN
15
Care and Maintenance
FCC Statement
1. Use or store this product in an environment with a temperature ranging from -25°C
(-13°F) to 60°C (140°F) and keep this product away from water sources, heat sources,
and metal objects.
2. For safety reasons, do not store this product in an environment where the temperature
is higher than 45°C (113°F) or lower than 0°C (32°F) for a long time.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This equipment may not cause harmful interference, and
(2) This equipment must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

EcoFlow EFM100 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues