Bercomac 700374-2 700378-2 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
1
OWNER’S MANUAL
Model Number
700374-2
700378-2
Berco
Northeast Two Stage 44" & 48’’ Snowblower
for
LAWN, YARD & GARDEN TRACTORS
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
104751_EN K-09
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
*104751_EN*
2
LIMITED WARRANTY
Bercomac Limitée
92, Fortin North, Adstock, Quebec, Canada, G0N 1S0
Conditions and Products Covered:
BERCOMAC guarantees any part of the product or accessory
manufactured by BERCOMAC and found in the reasonable
judgment of BERCOMAC to be defective in material and or
workmanship will be repaired or replaced by an authorized
dealer without charge up to our maximum labor rates and pre-
established times. For replacement parts only standard ground
freight services are covered. This warranty extends to the
original retail purchaser only and is not transferable to any
subsequent purchasers.
Warranty Period
(from date of the original retail purchase)
xResidential use: 1 year
xSemi-commercial, professional or rental use: 90 days
Exceptions Noted Below; the following items are guaranteed
by the original manufacturer and have their own warranty,
conditions and limited time:
xTire Chains: 90 days
xEngines: Will vary as per the manufacturer
Please refer to the engine manufacturer’s warranty
statement included with the unit. BERCOMAC is not
authorized to handle warranty adjustments on engines.
Items and Conditions NOT Covered:
This warranty does not cover the following:
xPick-up or delivery charges or in-home services fees.
xAny damage or deterioration of the unit, parts and or finish
of these due to normal use, wear and tear, or exposure.
xCost of regular use or maintenance service or parts, such as
gas, oil, lubricants, tune-up parts, and adjustments.
xAny part or accessory which has been altered, modified,
misused, neglected, accidentally damaged or not properly
installed, maintained, stored or repaired not in accordance
with the instructions in the owner’s manual.
xRepair due to normal wear and or any wear items such as
shear pins, bolts, belts, etc.
xExpedited freight fee services for replacement parts.
xShear bolts and shear pins are to be considered as a
preventive measure not as an assured protection, any
damages resulting from the lack of shear bolts breakage are
not covered.
NOTE: All warranty work must be performed by an authorized
dealer using original (manufacturer) replacement parts.
Owner’s Responsibilities:
BERCOMAC’s defective equipment or part must be returned
to an authorized dealer within the warranty period for repairs.
In the event that defective merchandise must be returned to
manufacturer for repairs, freight fees are prepaid and a written
authorization from BERCOMAC must be obtained by dealer
prior to the shipment. This warranty extends only to
equipment operated under normal conditions. To validate a
warranty claim, it is the user’s responsibility to maintain and
service the unit as specified in the owner’s manual or to have
the unit serviced at their dealer at their expense.
General Conditions:
The sole liability of BERCOMAC with respect to this warranty
shall be strictly and exclusively repair and replacement as
mentioned herein. BERCOMAC shall not have any liability for
any other costs, loss or damage, including but not limited to,
any incidental or consequential loss or damage.
In particular, without being limited to, BERCOMAC shall have
no liability or responsibility for:
xTravel time, overtime, after hours time or other
extraordinary repair charges or relating to repairs and or
replacements outside of normal business hours.
xRental of like or similar replacement equipment during the
period of any, repair or replacement work.
xAny communicating or travel charges.
xLoss or damage to person or property other than that
covered by the terms of this warranty.
xAny claims for lost revenue, lost profit or any similar costs
as a result of damage or repair.
xAttorney’s fees.
BERCOMAC’s responsibility in respect to claims is limited to
making the required repairs or replacement without charge up
to our maximum labor rates and pre-established times and no
claim of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any product or accessory.
This warranty gives you specific legal rights. You may also
have other rights, which vary from state to state.
NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify
any product previously manufactured.
Instructions for Obtaining Warranty Services:
Contact dealer where equipment was purchased or any other BERCOMAC service dealer to arrange service at their dealership. To
locate a dealer convenient to you, access our website at www.bercomac.com. Don't forget to bring the product and your proof of
purchase (sales receipt) to the BERCOMAC dealer.
1
INTRODUCTION ...................................................................................................................................... 2
SAFETY PRECAUTIONS ......................................................................................................................... 3
SAFETY DECALS ..................................................................................................................................... 5
ASSEMBLY
Tools required ................................................................................................................. 6
Step 1: Snowblower Preparation ................................................................................................. 6
Step 2: Snowblower Installation ................................................................................................... 7
OPERATION
Snowblower Operation ................................................................................................................. 9
Controls ........................................................................................................................................ 9
Snow Removal ............................................................................................................................. 9
Cleaning a Clogged Discharge Chute .......................................................................................... 9
MAINTENANCE
Maintenance ................................................................................................................................ 10
Adjustments ................................................................................................................................. 10
Lubrication ................................................................................................................................... 10
Cutting Edge Maintenance ........................................................................................................... 10
Auger and Fan Shear Bolt Replacement ..................................................................................... 10
Belt Installation, Adjustment and Replacement ........................................................................... 11
REPLACEMENT OF ONE OR TWO SECTIONS OF THE AUGER AND / OR GEAR BOX .................... 12
DISMOUNTING & STORAGE
Snowblower Dismounting ............................................................................................................ 13
End of Season Storage ................................................................................................................ 13
TROUBLESHOOTING .............................................................................................................................. 14
PARTS BREAKDOWN & LISTS
Chute .......................................................................................................................................... 16
Snowblower ................................................................................................................................. 18
TORQUE SPECIFICATION TABLE .......................................................................................................... 22
OPTIONS & ATTACHMENTS ............................................................................................... 23
TABLE OF CONTENTS
Page
2
INTRODUCTION
TO THE PURCHASER
This new accessory was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your attachment.
NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to
use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will
use this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS
MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.
DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF
HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions
are not followed.
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are
not followed.
CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are
not followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
SERIAL NUMBER : ___________________________
(IF APPLICABLE)
MODEL NUMBER: ___________________________
PURCHASE DATE : ___________________________
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle
and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the accessory.
GLOSSARY:
In this manual, right and left sides are determined by
sitting on the seat of the vehicle facing forward.
In this manual, "accessories" means attachments
(snowblower, rotary broom, blade etc.) that you install
on the vehicle (lawn tractors, A.T.V. s etc).
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the
accessory’s safety labels to warn of the
possibility of serious injury. Please take
special care in reading and understanding
the safety precautions before operating the
vehicle and accessory.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and accessory. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate the vehicle nor the
accessory. Never allow adults to operate the vehicle
nor the accessory without proper instructions.
3. No one should operate the vehicle nor the
accessory while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all people,
particularly small children and pets.
PREPARATION:
1. Thoroughly inspect the area where the accessory
is to be used and remove door mats, all foreign
objects and the like.
2. For motorized accessories, disengage all clutches
and shift into neutral before starting engine.
3. Do not operate the accessory without wearing
adequate winter outer garments. Avoid loose fitting
clothing that can get caught in moving parts. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot engine.
c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
e) When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
6. Let the vehicle and accessory adjust to outdoor
temperatures before using.
7. Never use an accessory without proper guards,
plates, or other safety protective devices in place
8. Always make sure to wear the appropriate safety
equipment required (glasses, muffs, mask…) for
each type of product. See operation section.
9. Always make sure of having safe traction on the
vehicle by using the recommended accessories
(chains, A.T.V. tracks, counterweights…). See
operation section.
10. Never modify the accessory or any part without
the written consent from the manufacturer.
4
OPERATION:
1. Do not put hands or feet near, under or inside rotating
parts.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic. Do not carry passengers.
3. After striking a foreign object, stop the engine (motor),
disconnect the wire from the spark plug(s) and keep
wire away to prevent accidental starting. Thoroughly
inspect the accessory for any damage and repair
damage before restarting and using the accessory.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5. Take all possible precautions when leaving the
vehicle unattended. Disengage the power take-off,
lower the attachment, place the transmission into
neutral, set the parking brake, stop the engine and
remove the contact key.
6. Do not run the engine indoors, except when starting
the engine and for transporting in or out of the
building. Do not operate or let motor run in a storage
area without ventilation because gas contains
carbon monoxide which is odorless, colorless and
can cause death.
7. Never use the accessories across the face of
slopes, go from top to bottom. Exercise extreme
caution when using equipment on slopes. Do not
attempt to clear a steep slope.
8. Never tolerate bystanders in the working zone.
Never use an accessory in the direction of
bystanders, it might throw gravel or debris that can
hurt people or damage property.
9. Never operate the accessory at high transport
speeds on slippery surfaces. Use care when
backing up.
10. Do not carry passengers.
11. Disengage power to the accessory when it is
transported or not in use.
12. Never operate the accessory without good visibility
or light.
13. Keep the accessory away from heat sources or
flames.
MAINTENANCE AND STORAGE
1. When cleaning, repairing or inspecting the vehicle
and accessory, make certain that all moving parts
have stopped. Disconnect wire from the spark
plug(s) and keep wire away to prevent accidental
starting.
2. Check all the bolts and components at frequent
intervals to make sure that they are properly
tightened.
3. Never store a motorized accessory with fuel in the
fuel tank inside a building where ignition sources are
present such as hot water and space heaters,
clothes dryers, and the like. Allow the engine to cool
before storing in any enclosure.
4. Always refer to the owner’s manual when you store
the accessory and vehicle for a prolonged or an
unspecified length of time.
5. Maintain or replace safety and instruction labels, as
necessary.
6 For winter accessories, (if applicable), let the engine
run for a few minutes after clean snow in order to
prevent the rotary parts from freezing.
7. Inspect the vehicle’s and accessorys air filter every
day. Clean it or replace it as necessary. Change the
oil more often when working in dusty conditions.
See the vehicle’s and accessory's owner’s manual.
THIS SYMBOL MEANS
DANGER !
BECOME ALERT !
YOUR SAFETY IS INVOLVED !
SAFETY PRECAUTIONS
5
SAFETY DECALS
REPLACE IF DECALS ARE DAMAGED
SEE PARTS BREAKDOWN FOR DECAL LOCATION
Decal # 102125 Decal # 102126
Decal # 102127 Decal # 103951
Decal # 102124
Decal # 102128
6
ASSEMBLY
STEP 1
SNOWBLOWER PREPARATION:
Install the hand guard (item 1) in the chute (item 2) as
shown.
Secure in place with two 1/4 x 3/4" hex bolts, two flat
washers and two 1/4’’ flange nuts on the inside.
Tighten firmly.
Install chute
Before installing the chute (item 1), loosen the two
flange nuts (item 2) (down to the last threads) which
holds the rotation system (item 3).
Install the rotation ring (item 4) over opening (item 5)
as shown and align the notches.
Place the chute (item 1) (facing the rear) and clip the
back over the rotation ring then turn the chute
towards the front to lock into place.
Reinstall the rotation system by tightening the flange
nuts firmly.
TOOLS REQUIRED
1 Wrench 7/16’’
1 Ratchet
1 Extension for ratchet
1Socket 7/16’’
Install hand guard
Insert the handgrip (item 1) on the handle (item 4) as
shown.
Insert the handle hook (item 2) into the handle and
secure with a 2.5 mm hair pin (item 3) as shown.
NOTE: Store these parts safely until you install the
snowblower.
Prepare the handle
7
STEP 2
SNOWBLOWER INSTALLATION:
Refer to parts breakdown section for parts
identification.
ASSEMBLY
NOTE: See belt installation instructions in the
Maintenance section.
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
Attach the snowblower to the subframe as shown.
Make sure the snowblower is pushed in until locked
into place by the springs (item 3).
Lift the snowblower.
Turn the tension arm (item 1) towards the back and
install the chain (item 2) on the hook (if subframe is
equipped with one)
Turn the tension arm towards the front to apply
tension on the spring.
Lower the snowblower.
Install snowblower and lift assist spring
CAUTION
The belt tension and lift assist spring arm are
spring loaded & need to be held firmly while
displacing to prevent injury.
CAUTION
Never use the snowblower without the belt guard.
WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
8
ASSEMBLY
VERIFY SKID SHOE ADJUSTMENT:
LEVEL PAVED SURFACE: Adjust skid shoes to allow
3/16" to 1/4" or 5mm to 7mm clearance (A) between
cutting edge and surface.
UNEVEN OR GRAVEL SURFACE: Adjust skid shoes
to allow 1/2" to 5/8" or 13mm to 16mm clearance (A)
between cutting edge and surface.
VERIFY TIRE PRESSURE:
Check and adjust tractor tire pressure as follows:
Front tires: 14-15 psi
Back tires: 7-8 psi
Tire pressure must be even on both sides of tractor.
Install handle
Adjust skid shoes
Remove the 2.5mm hair pin (item 1) and hook (item
3) from the prepared handle (item 2).
Insert handle into the handle support and put the
hook and hair pin in place.
9
SNOWBLOWER OPERATION
a) Make sure the snowblower is clear of snow
before engaging the snowblower.
b) Make sure that the auger and impeller operate
freely.
c) Start the tractor engine.
d) Before engaging the snowblower drive, always
have the engine running at medium R.P.M.
e) Operate the snowblower at maximum engine
R.P.M.
IMPORTANT: USE FULL ENGINE R.P.M. WHEN
REMOVING WET OR STICKY SNOW. LOW R.P.M.
WILL TEND TO PLUG THE CHUTE.
CONTROLS
CHUTE ROTATION
The chute rotation handle is located to the left of
steering wheel. Turning the handle in a clockwise
direction, the discharge chute will turn in a clockwise
direction or vice versa.
CHUTE DEFLECTOR
Set the angle of the deflector according to the distance
the snow must be thrown and to prevent property
damage. To change the deflector angle, loosen the two
deflector knobs & adjust the deflector to the appropriate
angle and retighten the two knobs securely.
SNOW REMOVAL
When removing snow, do not use the snowblower as
a dozer blade to push snow. Allow snowblower to
ingest snow at its own speed. If the speed of your
tractor is too fast, the snowblower may become
overloaded and plug. For best results, raise the
snowblower and remove a top layer of snow. A
second pass with the snowblower will remove the
remaining snow.
OPERATION
WARNING
Read the tractor Owner’s Manual carefully. Be
thoroughly familiar with the controls & proper
use of the attachment. Know how to stop the
attachment & disengage the controls quickly.
WARNING
TO PREVENT INJURIES AND FOR MORE
TRACTION WHEN USING AN ATTACHMENT:
-Rear counterweight of 100 lbs. minimum is
required to counterbalance the attachment’s
weight.
-Tractor manufacturer approved tire chains are
required.
-Do not operate on a slope greater than 10°.
-When dismounting the attachment remove rear
counterweights.
WARNING
Hand contact with the rotating impeller inside the
discharge chute is the most common cause of
injury associated with snowblowers. Never use
your hand to clean out the discharge chute.
-Do not attempt to clear plugged chute, auger or
fan of snow while the snowblower's engine is
running.
-Disengage snowblower.
-Lower snowblower to the ground and set
parking brake.
-SHUT THE ENGINE OFF & REMOVE KEY!
-Wait 10 seconds to be sure that all moving parts
such as the impeller blades have stopped
moving.
-Disconnect wire from the spark plug(s) and keep
wire away to prevent accidental starting.
-Do not use hand to unplug chute use a clean-out
tool of at least 36” (1 m) length.
10
OPERATION
MAINTENANCE
a) Check mounting bolts at frequent intervals for
proper tightness in order to prevent costly repairs.
Make sure your snowblower is in safe working
condition.
b) Provide adequate blocking before working under
the snowblower when in raised position.
ADJUSTMENTS
SKID SHOE ADJUSTMENT:
LEVEL PAVED SURFACE: Adjust skid shoes to allow
3/16" to 1/4" or 5mm to 7mm clearance (A) between
cutting edge and surface.
UNEVEN OR GRAVEL SURFACE: Adjust skid shoes
to allow 1/2" to 5/8" or 13mm to 16mm clearance (A)
between cutting edge and surface.
MAINTENANCE
CUTTING EDGE MAINTENANCE
Verify from time to time the wearing on the cutting
edge to make sure you do not wear out the base of
the snowblower’s chassis. This cutting edge is
reversible.
WARNING
TO PREVENT INJURIES:
Stop the snowblower motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
SNOWBLOWER PULLEY REPLACEMENT
or ALIGNMENT:
Clean the parts before aligning or replacing the pulley.
Apply some "Loctite" 2760 on the key and the set
screws. Tighten firmly. (Use heat to soften the "loctite’’
when removing the set screws).
AUGERS AND FAN SHEAR BOLT
REPLACEMENT
Shear bolts are to be considered a preventive
measure and not an assured protection. Operator
vigilance is required. Thoroughly inspect the areas
where the snowblower is to be used and remove all
foreign objects.
To avoid damage to the snowblower:
Use only the original shear bolts (grooved bolts).
#104000 in bags of 10 for the augers.
#103999 in bags of 10 for the fan.
The use of any other shear bolt will not insure any
protection and may void the warranty.
IMPORTANT: IT IS VERY IMPORTANT TO REPLACE
THE AUGERS IN THE SAME POSITION AS SHOWN
IN THE DRAWING BEFORE INSTALLING THE
SHEAR BOLTS.
LUBRICATION
Grease the wheel axles, the fork pivots after every
sixteen hours of use.
Apply oil at all pivot points.
Chute Rotation System: Oil chute base, rotation worm
every sixteen hours of operation.
Gear box:
Check the oil annually. If necessary, add AGMA 5 EP or
SAE 90 oil.
The gear box should have a total of 155 ml of oil or filled
to the rim of the bolt hole when installed on the
snowblower. (see figure) Gear Box
11
MAINTENANCE
BELT INSTALLATION, ADJUSTMENT,
AND REPLACEMENT:
WARNING
The belt tension arm is spring loaded & needs to be
held firmly while displacing to prevent injury.
SNOWBLOWER BELT:
a) Lower the snowblower to the ground.
b) Remove the belt guard.
c) Remove tension on the belt by lowering the
tension arm (item 1)
d) Loosen the knob (item 2) on the bracket that holds
the bearing (item 3).
e) Install the belt as shown.
f)) Adjust the bracket by pushing on the bearing (item
3) to apply a slight pressure on the back of the belt
(just enough to hold the belt in place). It is normal
that the bearing is off centre (towards the vehicle)
on the pulley. Just make sure that it does not
come into contact with the wall of the pulley.
Position of the belts
Top view
Position of the bearing
g) Tighten firmly with the knob.
h) Apply tension on the belt by pulling up the tension
arm (item 1).
i) Engage the snowblower for a few seconds under
supervision. Stop the engine. Inspect the belt to
make sure it does not interfere with any parts; that
it is well inserted in the pulleys and that it has not
flipped on it’s side while still on the pulleys. The V
of the belt must be in the V of the pulleys. The
back of the belt must rest on the flat pulleys (D)
as shown.
j) Reinstall the belt guard.
k) Use genuine belts only, they are specifically
fabricated for this application.
NOTE: There must be a good tension on the belt at
all times. If spring is damaged or stretched, you must
replace it.
DRIVE MECHANISM BELT:
See subframe manual for belt replacement
instructions.
IMPORTANT:
When aligning or replacing the snowblower pulley
(item 4), you must clean the parts and use ‘’Lock-tite’’
2760 on the key and the set screws. Tighten firmly.
Distance between coils
Belt Insertion
CAUTION
Never use the snowblower without the belt guard.
12
For belt part numbers, refer to snowblower parts
breakdown section for parts identification
Snowblower must be detached & disconnected
from the tractor to replace the auger or the gear
box.
a) Remove the belt guard.
b) Remove the belt. See manual.
c) Turn the snowblower face down (optional).
d) Loosen the 2 set screws (item 1) on the pulley (it
may be necessary to heat the set screw and
center of pulley to soften the ‘’loctite’’).
e) Remove the pulley.
f) Loosen the 2 set screws (item 2) on the bearing
behind the snowblower (it may be necessary to
heat the set screw to soften the ‘’loctite’’).
g) Remove all the bolts (item 3) and the nuts that
support the gear box and its support.
h) Remove the assembly (gear box, its support, the
fan and augers) from the snowblower and save the
nylon bushings and bearings.
i) Replace the appropriate parts. Insert the shaft and
the key into the new gear box (if required).
j) Install the new auger or augers on their respective
side in the position shown with the same nylon
bushings on the shaft of the new gear box as
shown.
k) Re-install parts by repeating steps backwards.
IMPORTANT: You must clean the parts and apply
some "Loctite" 2760 on the key of the pulley and
the set screws of the bearing and pulley. Tighten
firmly.
Follow the instructions in the belt replacement
and adjustments sections.
REPLACEMENT OF ONE OR TWO SECTIONS OF THE AUGER
AND / OR GEAR BOX
13
DISMOUNTING & STORAGE
a) Remove the hair pin and the handle from the
rotation system.
b) Remove the belt guard and release the tension on
the belt by displacing the tension arm backwards.
The tension arm is spring loaded and needs to be
held firmly while lowering to prevent injuries.
Remove the belt.
c) Detach the snowblower by removing the lift assist
spring and by lifting the two spring locks on the
male quick hitch and pulling out the snowblower
one side at a time.
d) Reinstall the belt guard.
SNOWBLOWER DISMOUNTING
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brakes.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
CAUTION
The belt tension and lift assist spring arm are
spring loaded & need to be held firmly while
displacing to prevent injury.
END OF SEASON STORAGE
a) Clean snowblower and subframe thoroughly and
repaint all parts from which paint has worn.
b) List the replacement parts that will be needed for
the next season.
c) Store the snowblower and the subframe in a dry
place.
d) Follow the instructions in the Lubrication section.
WARNING
Never use the snowblower without the belt guard.
14
PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION
One section or both sections of the
auger stops turning.
Shear bolts are probably broken. Replace shear bolt (for identification,
see parts list "Snowblower").
Fan stops turning. Shear bolt is probably broken. Replace shear bolt (for identification,
see parts list "Snowblower").
Snowblower stops turning. One of the two belts is probably
damaged or broken.
Check both belts and replace
damaged belt(s) (for instructions, see
Maintenance section, Installation,
Adjustment and Replacement
section).
Belt has burn marks in specific
places.
Lack of tension on belt.
Snowblower engaged when
plugged.
Adjust manual clutch cable or replace
springs if stretched.
To obtain the proper tension, the
distance between the coils of the
spring should be .25’’ (1/4’’).
If not, remove the bolt, sleeve and the
spring from the original hole and
reinstall them in the second hole. (See
Maintenance section, Belt installation,
adjustment and replacement)
Make sure the auger & the fan are not
frozen or plugged before engaging.
Chute plugs easily. Tractor engine turning too slowly.
Advancing too quickly with tractor.
Run engine at full throttle during
snowblowing operation.
Allow snowblower to ingest snow at its
own speed.
Chute rotation is difficult. Dirt or ice may be underneath
chute.
Dismount chute by removing the
rotation worm (for identification, see
parts list "Chute with Rotation
System"). Turn the chute completely
towards the rear and it will disconnect
from base. Clean the base of chute
and the rotation ring. Lubricate & re-
install.
TROUBLESHOOTING
15
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION
Snowblower digs into ground. Ground is not frozen or too soft. Adjust skid shoes lower so they
may better support the snowblower.
If problem persists, change skid
shoes for heavy duty skid shoes
(option #700243) which cover more
surface and prevents snowblower
from digging.
Snowblower does not raise evenly. Tire pressure uneven from one side
to another.
Maladjustment of the snowblower.
Verify and adjust tire pressure:
Front tires: 14 to 15 psi
Rear tires: 7 to 8 psi
Loosen male hitch on snowblower
(for identification, see parts list
"Snowblower").
Place a shim (ex.:piece of wood
approx. 2” thick) under the lowest
side of snowblower which needs to
be leveled. Re-tighten bolts.
Snowblower vibrates or is
abnormally noisy.
Damaged pulley.
Damaged bearing.
Damaged fan.
Damaged auger.
Replace pulley.
Replace bearing.
Dismount & repair or replace fan.
Replace auger.
16
PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES
CHUTE / GOULOTTE
17
O/L = Obtain locally / obtenir localement
REF.
RÉF. DESCRIPTION DESCRIPTION QTY
QTÉ
PART #
PIÈCE #
1Chute Goulotte 1103936
2Rotation ring Anneau de rotation 1103943
3Flange nut 1/4" n.c. Écrou à bride 1/4" n.c. 2O/L
4Nylon flat washer 7/16" Rondelle plate de nylon 7/16" 2102011
5Carriage bolt 5/16" n.c. x 3/4" Boulon à carrosserie 5/16" n.c. x 3/4" 2O/L
6Nylon flat washer 11/32" Rondelle plate de nylon 11/32" 2102009
7Knob Bouton 2102020
8Hand guard Fourche protectrice 1102012
9Hex. bolt 1/4" n.c. x 3/4" Boulon hex. 1/4" n.c. x 3/4" 2O/L
10 Flat washer 5/16" hole Rondelle plate 5/16" trou 2O/L
11 Danger decal Décalque danger 1102127
12 Warning decal Décalque attention 1102125
PARTS LIST / LISTE DES PIÈCES
18
PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES
SNOWBLOWER / SOUFFLEUSE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Bercomac 700374-2 700378-2 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

dans d''autres langues