JBU Illuminto Q4 Manuel utilisateur

Marque: JBU

Modèle: Illuminto Q4

Taper: Manuel utilisateur

How to mirror/cast your smart device into the projector

To cast or mirror/cast your smart device’s screen on the Illuminto

Q4 projector, please follow these steps:

1. Make sure both the Illuminato Q4 and your smart device are

connected to the same WiFi network.

2. Open the “Mirracast” app on the Illuminato Q4.

3. Download a mirror/casting app from the Google Play store

onto your smart device if you don’t already have one.

4. Open your chosen casting app on your smart device. When

asked what device you would like to cast to/mirror, select “PJ-

33S.” Follow all instructions in your chosen app to complete

the setup.

5. Your Illuminato Q4 should now mirror your smart device’s

screen and audio.

To end mirroring/casting, press the Return (10) button on the

Illuminato Q4, and select “Tier Down,” or end mirroring/casting

from the app on your personal device.

Remote & Mouse

Operating and aiming the remote

(Install two (2) AAA batteries in the remote.) The machine has two

Infrared Sensors (25) on the front and back of the machine. For

best results, point the remote at these sensors rather than the

projection screen.

How to change EQ settings

The EQ settings allow you to adjust your audio balance for

dierent types of music. You can select from preset EQ settings by

pressing the EQ (L) button on the remote. The current EQ setting

will be displayed in the top left corner of the screen. Press the

remote’s EQ button again to cycle through each setting. When

your desired EQ setting has been reached, wait a few seconds

until the EQ display disappears. Your current EQ setting is now

selected.

How to use the mouse pointer on the remote

Pressing the Mouse (I) button on the remote once will make a virtual

mouse pointer appear on screen. Use the Navigation Controls (B)

to move the mouse pointer, and OK (G) to select. To return the

remote to the remote setting, press the Mouse button once more.

How to use the included plug-in mouse

When navigating third-party apps inside the OS system, it is

best to use the included plug-in mouse rather than the remote or

machine control panel. Simply plug the included mouse into USB

Slot #2 (19) and use it like any mouse to navigate the app

Maintenance

How to clean

Turn the machine and microphones o; (remember that there

are separate power buttons for the machine and the projector).

Unplug the machine’s power cord and disconnect any AUX, AV,

HDMI, or USB plug-ins.

Gently wipe the outside of the machine using a clean, dry cloth.

Keep all vents, buttons, and openings free of lint and dirt. Do not

immerse the machine in water and do not use any harsh cleaners.

How to store

Charge the machine so that it’s ready for the next use. Dock the

wireless microphones in their holsters. Make sure that the machine

is clean and dry.

Bind the power cord and mouse cable individually and gently

with electrician-approved fasteners. (Note: Do not wrap or fold

against the natural bend of the cords or cable. Do not wrap the

cord around the machine.)

Store the machine in a cool, dry place away from damaging

elements.

For best results, clean and store the machine after each use.

How to transport

The Illuminato Q4 was designed intentionally for easy transport

and mobility.

Begin by unplugging all wires from the machine.

Place the microphones in the two holders attached to the side of

the machine.

Extend the machine handle, grip it ﬁrmly, and lift the machine. The

machine will now travel like a briefcase

Problem Solution

Microphone

is not turning

The microphone battery is low or depleted.

Replace the AA batteries in the microphone.

Machine is

not turning

The battery is depleted. Be sure to charge the

machine after each use.

ALSO/OR

Remember that the machine has four power

buttons: Machine Power (26), Projector Power

(12), Projector Light (11), and the remote’s Power

button (A).

Both the Machine Power and the Projector

Power must be turned on in order for the

machine to operate.

The Projector

is not turning

If the machine appears to be powered on

correctly, press the Projector Light(11) button

to see if the machine is in sleep mode. If you

have pressed the projector light button and

the projector is still not turning on, power down

the machine and then power it back on again.

Smart OS is

not booting

First, ensure you are in Smart OS mode by

pressing the Input (15 or J) button and selecting

“Smart OS.” If this does not work, power the

machine down and power it back on once

more.

Problem Solution

The Menu (H)

button on the

remote is not

working

You cannot access menu settings using the

Menu button on the remote. Please use the

Settings (K) button on the remote or the Menu

(14) button on the projector itself.

USB mode is

not working

Try unplugging the USB from the machine and

plugging it back in again. If this does not work,

you may not have any readable data on your

USB drive.

Machine is

not playing

microphone

vocals

Ensure that the Mic Volume (7) is up on the

machine’s function board and that the pill

sliders on the microphones are also at a

sucient volume.

If there is still no audio output from the

microphone, please check the batteries.

The remote

control is not

working

Ensure you are aiming the remote at the

machine’s Infrared Sensors (25). You may also

try moving closer to the machine.

If this does not rectify the issue, please check

the remote’s batteries.

PLEASE NOTE: Fluorescent lighting may also

interfere with the remote’s signal. If you cannot

remove or turn o ﬂuorescent lights nearby, try

using the plug-in mouse instead.

Problem Solution

I cannot ﬁnd

the app I

downloaded.

You must add the app to the home screen.

Select the “+” tile in Smart OS, navigate to the

app you want, and press the Return (C or 10)

button.

If your app still won’t add, you may need to

remove an app from the home screen to make

room, also using the “+” function. (Please note

that removing apps from the home screen

does not uninstall them).

I’m having

diculty

navigating

inside an app

(e.g. “Netﬂix”)

For the most streamlined experience inside

apps, please use the included plugin mouse

in conjunction with the machine’s Return (10)

button.

Next song is

not playing

The loop setting of the music has been set to

“play one song” and must be reset to “play all”

in order for the next song to play. This setting

can be changed in the “Media Player” app.

Song name is

garbled

The title of the song ﬁle cannot be read.

Manually edit the song title on your computer

and retransfer the edited ﬁle to your USB drive.

Machine

powers on

and then

shuts down

Battery is low. Please charge the machine or

replace the battery if needed.

Problem Solution

No sound is

playing from

the speaker

Ensure that the volume on the machine (6),

remote (D), and your device (if applicable) are

all turned to an audible level.

Also, check to see whether you are on mute by

pressing Mute (F) on the remote control to see

if the audio resumes.

Button or

knob on the

machine/

remote

control is

not working

properly

Power o the machine and turn it back on.

Machine

is not

connecting

to WiFi

Please ensure that the WiFi router and the

machine are in close proximity to one another

and that the WiFi network is functioning

strongly. Please also ensure you have entered

your password correctly.

If the WiFi still won’t connect, try restarting

your router and reconnecting to the network

afterward.

If any of these issues persist or if any part of the machine becomes

damaged, discontinue use and consult a licensed electrician for repair.

Do not attempt to modify or repair the machine yourself. You can also

contact our customer service department (see back cover).

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any inte rference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interferenceto radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body.

ISED Statement

English: This device contains licence-exempt transmitter(s)/receiver(s) that

comply

with Innovation, Science and Economic Development Canada’s licence-exempt

RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may

cause

undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui

sont conformes aux RSS exemptés de licence d'Innovation, Sciences et

Développement économique Canada.

L'exploitation est soumise aux deux conditions suivantes :

(1) Cet appareil ne doit pas provoquer d'interférences.

(2) Cet appareil doit accepter toute interférence, y compris les interférences

susceptibles de provoquer un fonctionnement indésirable de l'appareil.

l'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b).

This device meets the exemption from the routine evaluation limits in section

2.5 of

RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian

Information

on RF exposure and compliance.

cet appareil est conforme à l'exemption des limites d'évaluation courante dans

la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les

utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux

champs rf et la conformité.

This equipment complies with Canada radiation exposure limits set forth for an

uncontrolled environment.

Cet équipement est conforme aux limites d'exposition aux rayonnements du

Canada établies pour un environnement non contrôlé.

This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

Cet équipement doit être installé et utilisé à une distance minimale de 20 cm

entre le radiateur et votre corps.

Don’t end things on a bad note

We’re here for you.

If you encounter any issues with your machine—or

if you have any questions or comments—please

feel free to contact us. Have your warranty

information on hand for faster service.

JBU Illuminto Q4 Manuel utilisateur

Marque: JBU

Modèle: Illuminto Q4

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: JBU Illuminto Q4 User manual

JBU Illuminto Q4 Manuel utilisateur

JBU Illuminto Q4 Manuel utilisateur

dans d''autres langues

Autres documents