ASROCK P4I65PE-M Le manuel du propriétaire

11

1

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published November 2004

22

2

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 16 Chassis Speaker Header (SPEAKER 1)

2 ATX 12V Connector (ATX12V1) 17 Chassis Fan Connector (CHA_FAN1)

3 CPU Socket 18 Clear CMOS Jumper (CLRCMOS0)

4 CPU Fan Connector (CPU_FAN1) 19 Infrared Module Header (IR1)

5 CPU Heatsink Retention Module 20 Floppy Connector (FLOPPY1)

6 184-pin DDR DIMM Slots (DDR1- 2) 21 Game Port Connector (GAME1)

7 Secondary IDE Connector (IDE2, Black) 22 Internal Audio Connector: AUX1 (White)

8 Primary IDE Connector (IDE1, Blue) 23 Internal Audio Connector: CD1 (Black)

9 North Bridge Controller 24 JR1 / JL1 Jumpers

10 AGP Slot (1.5V_AGP1) 25 Front Panel Audio Header (AUDIO1)

11 South Bridge Controller 26 PCI Slots (PCI1- 3)

12 USB 2.0 Header (USB67, Blue) 27 Shared USB 2.0 Header (USB4_5, Blue)

13 Secondary Serial ATA Connector (SATA2) 28 BIOS FWH Chip

14 Primary Serial ATA Connector (SATA1) 29 ATX Power Connector (ATXPWR1)

15 System Panel Header (PANEL1)

33

3

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB01)

2 RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 Serial Port: COM1

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 Shared USB 2.0 Ports (USB45)

44

4

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock P4i65PE-M motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest memory and CPU support lists on ASRock website as

well. ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock P4i65PE-M Motherboard

(Micro ATX Form Factor: 9.6-in x 7.8-in, 24.4 cm x 19.8 cm)

ASRock P4i65PE-M Quick Installation Guide

ASRock P4i65PE-M Support CD

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock I/O Plus

TM

Shield

55

5

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

1.2 Specifications1.2 Specifications

1.2 Specifications

Platform: Micro ATX Form Factor: 9.6-in x 7.8-in, 24.4 cm x 19.8 cm

CPU: Socket 478, supports Intel

®

Pentium

®

4

/ Celeron

®

(Prescott,

Northwood, Willamatte) processor

Chipsets: North Bridge:

Intel

®

865PE chipset, FSB @ 800 / 533 / 400MHz,

supports Hyper-Threading Technology (see CAUTION 1)

South Bridge:

Intel

®

ICH5, supports SATA 1.5Gb/s

Memory: 2 DDR DIMM Slots: DDR1 and DDR2

2 DDR DIMM Slots Supports PC3200 (DDR400) / PC2700

(DDR333) / PC2100 (DDR266), Max. 2GB

(see CAUTION 2)

Dual Channel Memory Technology support (see CAUTION 3)

IDE: IDE1: ATA 100 / Ultra DMA Mode 5

IDE2: ATA 100 / Ultra DMA Mode 5

Supports up to 4 IDE devices

Serial ATA: Supports up to 2 SATA devices at 1.5Gb/s data transfer rate

(Not Support “RAID and “Hot Plug” functions)

Floppy Port: Supports up to 2 floppy disk drives

Audio: 5.1 channels AC’97 Audio

PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor: CPU temperature sensing,

Chassis temperature sensing,

CPU overheat shutdown to protect CPU life

(ASRock U-COP)(see CAUTION 4),

CPU fan tachometer,

Chassis fan tachometer,

Voltage monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 3 PCI slots with PCI Specification 2.3

AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 5)

USB 2.0: 8 USB 2.0 ports:

includes 6 default USB 2.0 ports on the rear panel,

plus two headers to support 2 additional USB 2.0 ports

(see CAUTION 6)

ASRock I/O Plus

TM

: 1 PS/2 mouse port,

1 PS/2 keyboard port,

1 serial port: COM1,

1 parallel port: ECP/EPP support,

6 default USB 2.0 ports,

1 RJ 45 port,

Audio Jack: Line In / Line Out / Microphone

66

6

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

BIOS: AMI legal BIOS,

Supports “Plug and Play”,

ACPI 1.1 compliance wake up events,

Supports jumperfree,

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 7)

OS: Microsoft

®

Windows

®

98 SE / ME / 2000 / XP compliant

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 22

of “User Manual” in the Support CD.

2. Please check the table below for the memory support frequency and its

corresponding CPU FSB frequency.

CPU FSB Frequency Memory Support Frequency

800 DDR266, DDR320

*, DDR400

533 DDR266, DDR333

400 DDR266

* When you use an FSB800-CPU on this motherboard, it will run at

DDR320 if you adopt a DDR333 memory module.

3. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 8 for proper installation.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

5. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

6. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 / 2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/

ME.

7. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

77

7

ASRock P4i65PE-M Motherboard

2. Installation2. Installation

2. Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push down

the socket lever to secure the CPU. The lever clicks on the side tab to

indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

88

8

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

P4i65PE-M motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

99

9

ASRock P4i65PE-M Motherboard

2.3 Expansion Slots (PCI and AGP Slots)2.3 Expansion Slots (PCI and AGP Slots)

2.3 Expansion Slots (PCI and AGP Slots)

There are 3 PCI slots and 1 AGP slot on P4i65PE-M motherboard.

PCI slots: The PCI slots are used to install expansion cards that have the 32-bit

PCI interface.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot

has a special locking mechanism which can securely fasten the graph-

ics card inserted.

Do NOT use a 3.3V AGP card on the AGP slot of P4i65PE-M motherboard!

It may cause permanent damage!

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

EnglishEnglish

English

1010

10

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

2.4 Jumpers Setup2.4 Jumpers Setup

2.4 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “SHORT”. If no jumper cap

is placed on the pins, the jumper is “OPEN”.

The illustration shows a 3-pin jumper whose

pin1 and pin2 are “SHORT” when jumper cap

is placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1(see p.2 No. 24)

JL1(see p.2 No. 24)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS0, 2-pin jumper)

(see p.2 No. 18)

Note: CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord, then use a jumper

cap to short the pins on CLRCMOS0 for 3 seconds. Please remember to

remove the jumper cap after clearing the CMOS. If you need to clear the

CMOS when you just finish updating the BIOS, you must boot up the system

first, and then shut it down before you do the clear-CMOS action.

2-pin jumper

Short Open

1111

11

ASRock P4i65PE-M Motherboard

2.5 Onboard Headers and Connectors2.5 Onboard Headers and Connectors

2.5 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 20)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue) Secondary IDE connector (Black)

(39-pin IDE1, see p.2 No. 8) (39-pin IDE2, see p.2 No. 7)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 No. 14) connectors support SATA data

(SATA2: see p.2 No. 13) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-Conductor ATA 66/100 cable

the red-striped side to Pin1

EnglishEnglish

English

SATA2

SATA1

1212

12

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock I/O Plus

TM

accommo-

(9-pin USB67) dates 6 default USB 2.0 ports. If

(see p.2 No. 12) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

Shared USB 2.0 Header This USB45 connector is shared

(9-pin USB4_5) with the USB 2.0 ports 4,5 on

(see p.2 No. 27) ASRock I/O Plus

TM

. When using

the front panel USB ports by

attaching the front panel USB

cable to this connector

(USB4_5), the USB ports 4,5 on

ASRock I/O Plus

TM

will not be able

to function.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 19) and receiving infrared module.

Internal Audio Connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.2 No. 23) from sound sources such as

(AUX1: see p.2 No. 22) a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 No. 25) convenient connection and

control of audio devices.

connect to the

power supply

connect to the SATA

HDD power connector

CD1

AUX1

1313

13

ASRock P4i65PE-M Motherboard

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 15) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 16)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 17) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(3-pin CPU_FAN1) to this connector and match

(see p.2 No. 4) the black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 29)

Game Port Connector Connect a Game cable to this

(15-pin GAME1) connector if the Game port

(see p.2 No. 21) bracket is installed.

ATX 12V Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2, No. 2) ATX 12V plug to this connector

so that it can provides sufficient

power. Failing to do so will cause

the failure to power up.

EnglishEnglish

English

1414

14

ASRock P4i65PE-M Motherboard

EnglishEnglish

English

2.62.6

2.6

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA

(SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s primary

SATA connector (SATA1).

STEP 4: Connect the other end of the SATA data cable to the primary SATA hard

disk. If you just want to install only one SATA HDD, the installation

process is complete at this step. If you want to install two SATA HDDs,

please continue to do the following steps.

STEP 5: Connect the SATA power cable to the SATA hard disk.

STEP 6: Connect one end of the second SATA data cable to the motherboard’s

secondary SATA connector (SATA2).

STEP 7: Connect the other end of the SATA data cable to the secondary SATA hard

disk.

Before you install OS into the SATA hard disk, you need to check and

ensure the configuration of the OnBoard IDE Operate Mode option in

BIOS setup is correct according to the condition of your system. For

the configuration details, please refer to the instruction on page 25 of

“User Manual” in the Support CD.

1515

15

ASRock P4i65PE-M Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The BIOS Setup Utility is stored in the BIOS FWH chip. When you start up the

computer, please press <F2> during the Power-On-Self-Test (POST) to enter the

BIOS Setup Utility; otherwise, POST continues with its test routines. If you wish to

enter the BIOS Setup Utility after POST, please resume the system by pressing <Ctl>

+ <Alt> + <Delete>, or pressing the reset button on the system chassis. For the

detailed information about the BIOS Setup Utility, please refer to the User Manual

(PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file

“ASSETUP.EXE” from the “BIN” folder in the Support CD to display the menus.

EnglishEnglish

English

1616

16

ASRock P4i65PE-M Motherboard

1717

17

ASRock P4i65PE-M Motherboard

® ®

®

Intel

®

ICH5,

1818

18

ASRock P4i65PE-M Motherboard

®

1919

19

ASRock P4i65PE-M Motherboard

2020

20

ASRock P4i65PE-M Motherboard

La page charge ...

ASROCK P4I65PE-M Le manuel du propriétaire

ASROCK P4I65PE-M Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents