MTD TB144 Manuel utilisateur

Marque: MTD

Modèle: TB144

Catégorie: Outils de jardin

Taper: Manuel utilisateur

P/N 769-02190 (1/06)

CAUTION: Before using

this product, read this

manual and follow all

safety rules and operating

instructions.

Operator’s Manual

4-Cycle Garden

Cultivator

TB144

INTRODUCTION

TABLE OF CONTENTS

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . .8

Starting/Stopping Instructions . . . . . . . . . . . . . . . .10

Operating Instructions . . . . . . . . . . . . . . . . . . . . . .11

Maintenance and Repair Instructions . . . . . . . . . . .12

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

CARB / EPA Warranty Information . . . . . . . . . . . . .21

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . E22-E24

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the

states of California, Maine, Oregon and Washington.

All U.S. Forest Land and the state of California (Public

Resources Codes 4442 and 4443), Oregon and

Washington require, by law that certain internal

combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention

of fire. Check with your state or local authorities for

regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or

a fine. This unit is factory equipped with a spark

arrestor. If it requires replacement, ask your LOCAL

SERVICE DEALER to install the Accessory Part

#180890 Spark Arrestor Kit.

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

CALIFORNIA PROPOSITION 65 WARNING

RULES FOR SAFE OPERATION

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• All guards and safety attachments must be installed

properly before operating the unit.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace parts that are cracked,

chipped, or damaged in any way. Do not operate the

unit with loose or damaged parts.

• Carefully inspect the area before starting the unit.

Remove all debris and hard or sharp objects such as

glass, wire, etc.

• Be aware of the risk of injury to the head, hands and

feet.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets

outside a 50 feet (15 m.) radius; there still may be a

risk to bystanders from thrown objects. Bystanders

should be encouraged to wear eye protection. If you

are approached, stop the unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to

the operation or maintenance of the equipment.

SYMBOL MEANING

When using the unit,

you must follow the

safety rules. Please read these instructions

before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

WARNING:

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a

safety warning can

result in injury to yourself and others.

Always follow the safety precautions to

reduce the risk of fire, electric shock and

personal injury.

WARNING:

Failure to obey a

safety warning will

result in serious injury to yourself or to

others. Always follow the safety precautions

to reduce the risk of fire, electric shock and

personal injury.

DANGER:

Failure to obey a

safety warning may

result in property damage or personal injury

to yourself or to others. Always follow the

safety precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION:

Indicates

danger,

warning or caution. Attention is required in

order to avoid serious personal injury. May

be used in conjunction with other symbols

or pictographs.

SAFETY ALERT:

Gasoline is highly

flammable, and its

vapors can explode if ignited. Take the

following precautions:

WARNING:

Read the Operator’s Manual(s) and follow all

warnings and safety instructions.

Failure to do so can result in serious injury to the

operator and/or bystanders.

• Do not touch the engine or muffler. These parts get

extremely hot from operation. They remain hot for a

short time after you turn off the unit.

• Do not operate the engine faster than the speed

needed to cultivate. Do not run the engine at high

speed when you are not cultivating.

• Always stop the engine when cultivating is delayed or

when walking from one cultivating location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop and switch the engine to off for maintenance,

repair, or to install or remove the tines.

Use only original equipment manufacturer

replacement parts and accessories for this unit. These

are available from your authorized service dealer. Use

of any unauthorized parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the tines and

guard.

• To reduce fire hazard, replace faulty muffler and spark

arrestor, keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store the unit, with fuel in the tank, inside a

building where fumes may reach an open flame or

spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high

to prevent unauthorized use or damage, out of the

reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use. See the Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE

INSTRUCTIONS

• Always stop the engine and allow it to cool before filling

the fuel tank. Never remove the cap of the fuel tank, or

add fuel, when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where

there are no sparks or flames. Slowly remove the fuel

cap only after stopping engine. Do not smoke while

fueling or mixing fuel. Wipe up any spilled fuel from the

unit immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke or allow sparks and open flames near the area

while adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can kill. Operate

this unit only in a well ventilated outdoor area.

• Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1-1989 standards. Also wear

ear/hearing protection when operating this unit. Wear

a face or dust mask if the operation is dusty. Long

sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not

wear loose clothing, jewelry, short pants, sandals or

go barefoot. Secure hair above shoulder level.

• This unit has a clutch. The tines remains stationary

when the engine is idling. If it does not, have the unit

adjusted by an authorized service technician.

• Be sure the tines are not in contact with anything

before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. The operator and unit must

be in a stable position while starting. See

Starting/Stopping Instructions.

• Use the right tool. Only use this tool for the purpose

intended.

• Use extreme caution when reversing or pulling the unit

towards you.

• Do not overreach. Always keep proper footing and

balance. Take extra care when working on steep

slopes or inclines.

• Always hold the unit with both hands when operating.

Keep a firm grip on the grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the tines

when they are rotating.

RULES FOR SAFE OPERATION

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING:Thrown

objects and loud noise can cause

severe eye injury and hearing loss.

Wear eye protection meeting ANSI

Z87.1-1989 standards and ear

protection when operating this unit.

Use a full face shield when needed.

• KEEP BYSTANDERS AWAY

WARNING:Keep all

bystanders, especially children and

pets, at least 50 feet (15 m.) from the

operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING:Do not

operate without the proper guards in

place. Keep away from the rotating

tines.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF or STOP

• CHOKE CONTROL

1 • FULL choke position.

2 • PARTIAL choke position.

3 • RUN position.

• HOT SURFACE WARNING

Do not touch a hot muffler or

cylinder. You may get burned. These

parts get extremely hot from

operation. When turned off they

remain hot for a short time.

• GARDEN CULTIVATORS –

ROTATING TINES CAN CAUSE

SEVERE INJURY

WARNING:Stop the

engine and allow the tines to stop

before installing or removing tines,

or before cleaning or performing any

maintenance. Keep hands and feet

away from rotating tines.

RULES FOR SAFE OPERATION

KNOW YOUR UNIT

Tine Guard

Cultivator

Tines

Primer Bulb

Muffler

Handlebar

Knob

Starter Rope Grip

Handlebar

Throttle

Control

Choke

Control

Edger

Wheel

Edger

Blade

STOP/OFF (O)

START/ON (I)

Wheel Support

Bracket

Front Handle

Applications

• Cultivating sod and light to medium soil

• Cultivating in garden areas, around trees, etc.

• Edging

KNOW YOUR CULTIVATOR

ASSEMBLY INSTRUCTIONS

NOTE: Before setting up your cultivator / edger,

disconnect the spark plug wire from the spark

plug.

POSITIONING THE HANDLEBARS

1. Loosen the two knobs on the inside of the

handlebars (Fig. 1).

2. With the unit upright, swing the handlebars up into

the operating position (Fig. 1).

NOTE: Take care not to pinch the throttle cable or

switch wires when positioning the handlebar.

3. Tighten the knobs to secure the handlebars in place.

NOTE: Do not over-tighten the knobs.

4. Reconnect the spark plug wire to the spark plug.

ADJUSTING TINE DEPTH

To adjust the wheel support bracket proceed as follows:

1. Stop engine and disconnect spark plug to avoid

accidental starting.

2. Remove cotter pin from the clevis pin and slide clevis

pin out of tailpiece bracket (Fig. 3).

3. Slide the wheel support bracket up or down in the

tailpiece, aligning the holes to the desire height.

4. Place the clevis pin through the hole and secure with

cotter pin.

ATTACHING THE EDGER WHEEL AND

BLADE

To convert the cultivator to an edger proceed as follows:

1. Push the On/Off switch to Off (O) position to stop

engine and tines and disconnect spark plug to avoid

accidental starting.

NOTE: It may be necessary to lay the cultivator / edger

back in a horizontal position on a flat level surface

with the upper handle touching the ground.

2. Remove the click pin from each end of the tine shaft

and slide the tines off the shaft.

3. Slide the edger wheel, with the hub facing inward,

onto the right side of the tine shaft and secure with

the click pin in the inside hole (Fig. 4).

4. Slide the edger blade with the hub facing out onto

the left side of tine shaft and secure with the click pin

in the inside hole (Fig. 4).

5. The edger guide line indicates where cutting will

occur. Guide the unit along a flowerbed, sidewalk, or

driveway so the edger guide line is above the desired

line of cut.

Clevis Pin

Cotter Pin

Wheel

Support

Bracket

Tailpiece Bracket

Fig. 3

Fig. 4

Edger Guide

Line

Click Pin

Hub

Edger Blade

Edger Wheel

Fig. 1

Handlebar

Knob

Handlebars

Washer

Hole

Bolt

Fig. 2

Tine Shaft

OIL AND FUEL INFORMATION

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in

the crankcase is extremely important.

Check the oil before each use and change

the oil regularly. Using incorrect or dirty oil can cause

premature engine wear and failure.

Use a high-quality SAE 30 weight oil of API (American

Petroleum Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped without oil in the crankcase.

In order to avoid damage to the unit, put oil in

the crankcase before attempting to start unit.

Your unit is supplied with one 3.04 fluid oz. (90 ml.)

bottle of SAE 30 SF, SG, SH oil (Fig. 5).

NOTE: Save the bottle to measure the correct amount

for future oil changes. See Changing the Oil.

NOTE:

Your new 4-Cycle cultivator is shipped for

operation in conditions above 40°F (4°C). For

cold weather operation, where temperatures

fall below 40°F (4°C), use a high-quality SAE

10W30 weight oil of API (American Petroleum

Institute) service class SF, SG, SH.

1. Unscrew the oil bottle top and remove the paper seal

covering the opening. Replace the top and cut the

tip off the funnel spout (Fig. 5).

2. Place the unit on a flat level surface with the

cultivator in a horizontal position (Fig. 6).

3. Remove the oil plug / dipstick from the crankcase

(Fig. 7).

4. Pour the entire bottle of oil into the oil fill hole

(Fig. 8).

NOTE: Never add oil to the fuel or fuel tank.

5. Wipe up any oil that may have spilled and reinstall

the oil fill plug / dipstick.

The importance of checking and maintaining the proper

oil level in the crankcase cannot be overemphasized.

Check oil before each use and change as specified in

the Maintenance Schedule.

Fig. 5

Fig. 7

Funnel Spout

Fig. 8

Oil Fill

Fig. 6

Oil Fill Plug/Dipstick

Oil Fill

Plug/Dipstick

Oil Fill Hole

O-Ring

OVERFILLING OIL

CRANKCASE MAY

CAUSE PRODUCT DAMAGE. Check and

maintain the proper oil level in the crank

case; it is important and cannot be

overemphasized. Check the oil before each

use and change it as needed. See Changing

the Oil.

CAUTION:

Add fuel in a clean,

well ventilated

outdoor area. Wipe up any spilled fuel

immediately. Avoid creating a source of

ignition for spilt fuel. Do not start the engine

until fuel vapors dissipate.

WARNING:

Gasoline is

extremely

flammable. Ignited Vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap

slowly to avoid injury

from fuel spray. Never operate the unit

without the fuel cap securely in place

WARNING:

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper

unit performance. Be sure to use fresh,

clean, unleaded gasoline.

NOTE: This is a four cycle engine. In order to avoid

damage to the unit, do not mix oil with gasoline.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel form acids when stored.

When using alcohol-blended fuel, use fresh fuel that is

less than 60 days old.

Using Blended Fuels

If you choose to use a blended fuel, or if its use is

unavoidable, follow recommended precautions:

• Always use fresh unleaded gasoline

• Use Sta-Bil

or an equivalent

• Drain tank and run the engine dry before storing unit

Using Fuel Additives

The use of fuel additives, such as Sta-Bil

or an

equivalent, will inhibit corrosion and minimize the

formation of gum deposits. Using a fuel additive can

keep fuel from forming harmful deposits in the

carburetor for up to six (6) months. Add 0.8 oz. (23 ml.)

of fuel additive per gallon of fuel to an approved gas

container according to the instructions on the container.

NEVER add fuel additives directly to the unit's gas tank.

OIL AND FUEL INFORMATION

FUELING THE UNIT

NOTE: Fill or add fuel to the tank only when the

cultivator is in a horizontal position (Fig. 9).

1. Remove fuel cap. Remove the tag from the fuel tank

neck.

2. Place spout of gas container into the fill hole on the

fuel tank and fill tank.

NOTE: Do not overfill tank.

3. Wipe up any gasoline that may have spilled.

4. Reinstall the fuel cap.

5. Move the unit at least 30 ft. (9.1 m) from the fueling

source and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to

Federal, State and Local regulations.

Fig. 9

Fuel Cap

STARTING/STOPPING INSTRUCTIONS

1. Check the oil level in the crankcase. Refer to

Checking the Oil Level.

2. Fill the fuel tank with fresh, clean unleaded gasoline.

Refer to Fueling the Unit.

3. Put the On/Off Stop Control in the ON [

] position

(Fig. 10).

4. Place the choke lever in Position 1 (Fig. 11).

5. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in the

primer bulb and fuel lines (Fig. 11). If you can’t see

fuel in the bulb, press and release the bulb as many

times as it takes before you can see fuel in it.

6. Hold the throttle and handlebar with one hand and

grab the starter rope with your other hand. Use your

foot to hold down the cultivator (Fig. 12).

NOTE: Tilt the unit back slightly to bring the tines off the

ground when starting.

7. While squeezing the throttle control, pull the starter

rope with a smooth and steady pull. Repeat this 5

times.

8. Move the choke lever to Position 2.

9. While squeezing the throttle control, pull the starter

rope in the same manner as explained in Step 7. Pull

1 to 3 times to start the engine.

10. Keep the throttle squeezed and allow the engine to

warm up for 15 to 30 seconds.

11. Place the choke lever in Position 3. Release the

throttle control to the idle position and begin

operation.

IF... The engine does not start, repeat Steps 4 - 11.

IF... The engine fails to start after a few attempts, place

the choke lever in Position 3 and squeeze the

throttle control. Pull the starter rope 3 to 8 times.

The engine should start. If not, continue pulling

starter rope until the engine starts.

IF WARM... If the engine is already warm, make sure

the On/Off Stop control is in the ON position and

start the unit with the choke lever in Position 2. After

the unit starts, move the choke lever to Position 3.

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control. Allow the

engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position.

STARTING INSTRUCTIONS

Primer Bulb

Choke Lever

Fig. 12

Fig. 10

Throttle

Control

ON (I)

Fig. 11

Operate this unit only

in a well- ventilated

outdoor area. Carbon monoxide exhaust fumes

can be lethal in a confined area.

WARNING:

Avoid accidental

starting. Make sure

you are in the starting position when pulling

the starter rope (Fig. 12).

To avoid serious

injury, the operator and unit must be in a stable

position while starting.

WARNING:

OFF (O)

Position 3

Position 1

Position 2

OPERATING INSTRUCTIONS

TRANSPORTING THE UNIT

1. Stop the engine.

2. Tilt the unit back until the tines clear the ground.

3. Push or pull the unit to the next location to be

cultivated.

Fig. 13

OPERATING TIPS

1. Move the cultivator to the work area prior to starting

the engine. Transport the cultivator by pushing or

pulling it along on its wheels.

2. Start the unit by following the Starting Instructions.

3. With the engine running and the tines off the ground,

depress the throttle control to increase the engine

speed.

4. While holding the upper handle with both hands,

slowly lower the cultivator until the tines make

contact with the ground (Fig. 13).

5. As cultivating action begins, tilt the cultivator up

slightly using the handle so that the tines can

penetrate the ground.

6. Once the ground has been broken, continue at a

moderate pace until you are familiar with the controls

and the handling of the cultivator.

7. If the tines are digging too deep or not deep enough,

adjust the wheel bracket as described in Adjusting

Tine Depth.

To prevent serious

personal injury, use

extreme caution when reversing

or pulling the unit towards you.

WARNING:

To prevent serious

personal injury,

never pick-up or carry the unit while the

engine is running.

WARNING:

To prevent serious

personal injury,

always stop the engine when operation is

delayed or when transporting the unit from

one location to another

WARNING:

Dress properly to

reduce the risk of

injury when operating this unit. Do not

wear loose clothing or jewelry. Wear eye

and ear/hearing protection. Wear heavy

long pants, boots and gloves. Do not wear

short pants, sandals or operate barefoot.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

Click Pin

“A” Tine

Fig. 14

TINE REMOVAL AND REPLACEMENT

All 4 tines should be replaced at the same time because

they will wear evenly through normal use. Work on one

side at a time.

1. Put the On/Off Stop Control in the STOP (O) position

and disconnect the spark plug wire.

NOTE: It may be necessary to lay the cultivator back in a

horizontal position on a flat level surface with the

upper handle touching the ground.

2. Remove the click pin from each end of the tine shaft.

Slide the tines off of the shaft (Fig. 14).

3. Clean and oil the shaft.

4. Slide on the new tines with the hubs facing out. The

four tines are marked with the letters “A” or “B.”

“B” Tine

Hubs

To prevent serious

personal injury,

always wear heavy gloves when handling

the tines.

WARNING:

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures, take your unit to a Troy-Bilt or

other qualified service dealer. Call 1-800-520-

5520 for more information.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by a Troy-Bilt or other qualified service

dealer. Call 1-800-520-5520 for more information.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine

Fill fuel tank with fresh fuel

Check oil

Page 9

Page 13

Every 10 hours Clean and re-oil air filter Page 14

First change at 10 hours

Every 25 hours thereafter

Every 25 hours

Change oil

Clean spark arrestor

Page 13

Page 17

Every 25 hours Check spark plug condition and gap Page 17

To prevent serious

injury, never perform

maintenance or repairs with unit running.

Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

WARNING:

5. Place one “A” tine and one “B” tine onto the shaft.

6. Secure the new tines to the shaft with click pins. It

may be necessary to wash the dirt off the tines and

shaft for ease of removal.

MAINTENANCE AND REPAIR INSTRUCTIONS

CHECKING THE OIL LEVEL

The importance of checking and maintaining the proper

oil level in the crankcase cannot be overemphasized.

Check oil before each use:

1. Stop the engine and allow oil to drain into the crankcase.

2. Place the unit on a flat, level surface to get a proper

oil level reading (Fig. 9).

3. Keep dirt, grass clippings and other debris out of the

engine. Clean the area around the oil fill plug/dipstick

before removing it.

4. Remove the oil fill plug/dipstick and wipe off oil.

Reinsert it all the way back in.

5. Remove the oil fill plug/dipstick and check the oil level.

Oil should be up to the top of the dipstick (Fig. 15).

6. If the level is low, add a small amount of oil to the oil

fill hole and recheck (Fig. 16). Repeat this procedure

until the oil level reaches the top of the dipstick.

NOTE: Do not overfill the unit.

Top of Dipstick

O-Ring

Oil Fill Plug/Dipstick

CHANGING THE OIL

For a new engine, change the oil after the first 10 hours of

operation. Change the oil while the engine is still warm. The

oil will flow freely and carry away more impurities.

1. Unplug spark plug wire to prevent accidental starting.

2. Remove the oil fill plug/dipstick.

3. Pour the oil out of the oil fill hole and into a container

by tipping the unit to a vertical position (Fig. 17).

Allow ample time for complete drainage.

Fig. 17

Fig. 15

Fig. 16

NOTE: Make sure the O-ring is in place on the oil fill

plug/dipstick when checking and changing the

oil (Fig. 16).

Full

Add 1.4-1.5 Oz.

(41-44 ml)

6. Replace the oil fill plug/dipstick.

7. Reconnect the spark plug wire.

4. Wipe up any oil residue on the unit and clean up any

oil that may have spilled. Dispose of the oil

according to Federal, State and local regulations.

5. Refill the crankcase with 3.04 fluid ounce (90 ml) of

SAE 30 SF, SG, SH oil.

NOTE: Use the bottle and spout saved from initial use to

measure the correct amount of oil. Pour fresh

fuel into the bottle and fill it to the top of the

label. The top of the label on the bottle measures

approximately 3.04 ounces (90 ml). Check the level

with the dipstick. If the level is low, add a small

amount of oil and recheck. Do not overfill (Fig. 18).

Fill Level

Fig. 18

Wear gloves to

prevent injury when

handling the unit.

CAUTION:

To prevent extensive

engine wear and

damage to the unit, always maintain the

proper oil level in the crankcase. Never

operate the unit with the oil level below the

bottom of the dipstick.

CAUTION:

Oil Fill Plug/Dipstick

Oil Fill Hole

O-Ring

MAINTENANCE AND REPAIR INSTRUCTIONS

AIR FILTER MAINTENANCE

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain

your air filter properly can result in poor performance or

can cause permanent damage to your engine.

1. Open the air filter cover. Push the tab on the left side

of the cover in, swing the air filter cover out and off

the air filter housing (Fig. 19).

2. Remove the air filter and the screen that sits

behind it (Fig. 19).

3. Wash the filter in detergent and water (Fig. 20). Rinse

the filter thoroughly and allow it to dry.

4. Apply enough clean SAE 30 motor oil to lightly coat

the filter (Fig. 21).

Fig. 20

5. Squeeze the filter to spread and remove excess oil

(Fig. 21).

6. Replace the filter (Fig. 19).

NOTE: If the unit is operated without the air filter, you

will VOID the warranty.

7. Reinstall the air filter cover. Position the hooks on

the right side of the air filter cover into the slots at

the right side of the air filter housing.

8. Swing the cover to the left until the tab on the air

filter cover snaps into place in the slot on the left

side of the air filter housing (Fig. 18).

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable. An idle

adjustment screw is reached though a hole in the top of

the engine cover (Fig. 22).

NOTE: Careless adjustments can seriously damage your

unit. For carburetor adjustments, take your unit

to a Sears or other qualified service dealer.

Check Fuel

Old fuel is usually the reason for improper unit

performance. Drain and refill the tank with fresh fuel prior

to making any adjustments. Refer to Oil and Fuel

Information.

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow. This is

often mistaken for an out of adjustment carburetor.

Check the condition of the air filter before adjusting the

idle speed screw. Refer to Air Filter Maintenance.

Air Filter

Screen

Hooks

Slot

Choke Lever

Air Filter Cover

Air Filter Housing

Tab

Fig. 19

Adjust Idle Speed Screw

If, after checking the fuel and cleaning the air filter, the

engine still will not idle, adjust the idle speed screw as

follows:

1. Start the engine and let it run at a high idle for a minute

to warm up. Refer to Starting/Stopping Instructions.

This unit needs to

run during idle

speed adjustment. Wear protective clothing

and observe all safety instructions to

prevent serious personal injury.

WARNING:

To avoid serious

personal injury,

always turn the unit off and allow it to cool

before you clean or service it.

WARNING:

Fig. 21

MAINTENANCE AND REPAIR INSTRUCTIONS

3. Disconnect the spark plug wire.

4. Clean dirt from around the spark plug. Remove the

spark plug from the cylinder head by turning it

counterclockwise with a 5/8” socket.

5. Remove the engine cover.

NOTE: To ease engine cover removal, pull the starter

rope out a little to give some slack.

6. Clean dirt from around the rocker arm cover.

Remove the screw holding the rocker arm cover with

a large flat blade screwdriver or Torx T-25 bit

(Fig. 27). Remove the rocker arm cover and gasket.

Rocker Arm Cover

Fig. 27

Spark Plug Hole

Gasket

Remove

Screws

Engine Cover

Fig. 25

Muffler

ROCKER ARM CLEARANCE

The rocker arm clearance may need adjustment if your

unit suffers a loss of performance power or has trouble

starting. Adjusting the rocker arm clearance requires

disassembly of the engine. If you feel unsure or

unqualified to perform this, take the unit to a Sears or

other qualified service dealer.

NOTE: Inspect the valve to rocker arm clearance with a

feeler gauge after the first 10 hours of operation

and then every 25 hours of operation thereafter.

• The engine must be cold when checking or adjusting

the valve clearance.

• This task should be performed inside, in a clean,

dust free area.

To adjust the rocker arm clearance:

1. Remove the two (2) screws on top of the engine cover

with a Flat-head or T-25 Torx screwdriver (Fig. 25).

2. Remove the screw behind the engine cover (Fig. 26).

Top View Of The Engine

Screw

Fig. 26

Idle Adjustment Screw

Checking the fuel, cleaning the air filter, and adjusting

the idle speed should solve most engine problems. If not

and all of the following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by a Troy-Bilt or other

qualified service dealer.

Fig. 22

NOTE: Ensure the tines are not in contact with the

ground when adjusting the idle.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips or flat blade

screwdriver into the hole in the air filter/muffler cover

(Fig. 22). Turn the idle speed screw in, clockwise, 1/8 of

a turn at a time (as needed) until the engine idles

smoothly.

NOTE: The tines should not rotate when the engine idles.

3. If the tines rotate when the engine idles, turn the idle

speed screw counterclockwise 1/8 of a turn at a time

(as needed), to reduce idle speed.

7. Pull the starter rope slowly to bring the piston to the top

of its travel, (known as top dead center). Check that:

• The piston is at the top of its travel while looking in

the spark plug hole (Fig. 27)

• Both rocker arms move freely, and both valves are

closed

If these statements are not true, repeat this step.

8. Slide the feeler gauge between the rocker arm and

the valve return spring. Measure the clearance

between the valve stem and rocker arm (Fig. 29).

Measure both the intake and exhaust valves.

Adjusting Nuts

Feeler Gauge

Rocker Arms

Fig. 28

Fig. 29

The recommended clearance for both intake and

exhaust is 0.003 – 0.006 in. (0.076 – 0.152 mm). Use a

standard automotive 0.005 in. (0.127 mm) feeler gauge.

The feeler gauge should slide between the rocker arm

and valve stem with a slight amount of resistance,

without binding. See Figure 28 and 29.

9. If the clearance is not within specification:

a. Turn the adjusting nut using a 5/16 inch (8 mm)

wrench or nut driver (Fig. 29).

• To increase clearance, turn the adjusting nut

counterclockwise.

• To decrease clearance, turn the adjusting nut

clockwise.

b. Recheck both clearances, and adjust as necessary.

10. Reinstall the rocker arm cover using a new gasket.

Torque the screw to 20–30 in

•lb (2.2–3.4 N•m).

11. Reinstall the engine cover. Check alignment of the

cover before tightening the screws. Tighten screws.

12. Check the spark plug and reinstall. See Replacing

the Spark Plug.

13. Replace the spark plug wire.

INTAKE

EXHAUST

Feeler Gauge

Adjusting Nut

Rocker Arm

0.003–0.006 in.

(0.076–0.152 mm)

Valve Stem

MAINTENANCE AND REPAIR INSTRUCTIONS

0.025 in.

(0.655 mm.)

REPLACING THE SPARK PLUG

Use a replacement Champion RDZ19H spark plug. The

correct air gap is 0.025 in. (0.655 mm.). Remove the plug

after every 25 hours of operation and check its

condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull the cap from the spark plug.

2. Clean dirt from around the spark plug. Remove the

spark plug from the cylinder head by turning it

counterclockwise with a 5/8” socket.

3. Replace cracked, fouled or dirty spark plug. Set the air

gap at 0.025 in. (0.655 mm.) using a feeler gauge (Fig. 23).

Fig. 23

4. Install a correctly-gapped spark plug in the cylinder

head. Turn the 5/8 in. socket clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

Fig. 24

Muffler

Spark Arrestor Screen

Spark Arrestor Cover

Screw

Tab

Slot

SPARK ARRESTOR MAINTENANCE

1. Remove the muffler cover. See Rocker Arm Clearance.

2. With a flat blade screwdriver or Torx T-20 bit,

remove the screw attaching the spark arrestor cover

to the muffler (Fig. 24).

3. Pull the tab on the spark arrestor cover out of the

muffler. Remove the spark arrestor cover.

4. Remove the spark arrestor screen from the spark

arrestor cover.

5. Clean the spark arrestor screen with a wire brush or

replace it.

6. Reinstall the spark arrestor screen, spark arrestor

cover and screw.

Do not sand blast,

scrape or clean

electrodes. Grit in the engine could damage

the cylinder.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

Cleaning the Unit

• Use a small brush to clean off the outside of the unit

and to keep the air vents free of obstructions.

• Do not use strong detergents or petroleum based

cleaners, such as kerosene. Some household

cleaners contain aromatic oils such as pine and

lemon that can damage the plastic housings or

handles. Wipe off any moisture with a soft cloth.

Storage

• Never store the unit with fuel in the tank where

fumes may reach an open flame or spark.

• Allow the engine to cool before storing.

• Store the unit in a locked up area to prevent

unauthorized use or damage.

• Store the unit in a dry, well-ventilated area. Do not

store next to corrosive material like fertilizer.

• Store the unit out of the reach of children.

Long Term Storage

If the unit will be stored for an extended time:

1. Carefully drain all gasoline from the fuel tank by

removing the fuel cap and tipping the motor housing

over to allow the fuel to drain into an approved gas

container. Do not use gas that has been stored for

more than 60 days. Dispose of the old gasoline in

accordance with Federal, State and Local

regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all gasoline has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of high quality motor oil into the

cylinder. Pull the starter rope slowly to distribute the

oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

unit after storage.

4. Change the oil, referring to the Changing the Oil

section. Dispose of the old oil in accordance with

Federal, State and Local regulations.

5. Thoroughly clean the unit and inspect for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts.

6. To take up less storage area, loosen the handlebar

knobs and fold the handlebar down. The unit is

ready for storage.

Transporting

• Allow the engine to cool before transporting.

• Secure the unit while transporting.

• Drain the fuel tank before transporting.

• Tighten fuel cap before transporting.

To avoid serious

personal injury,

always turn the unit off and allow it to cool

before you clean or perform any

maintenance on it.

WARNING:

TROUBLESHOOTING

NOTE: For repairs beyond the minor adjustments listed above, contact your nearest Troy-Bilt Parts &

Repair center (1-800-520-5520) or other qualified service dealer for an adjustment.

CAUSE ACTION

Oil fill plug/dipstick loose or missing o-ring Tighten oil fill plug/dipstick, replace o-ring

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take unit to a Troy-Bilt or other qualified service dealer for

an adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

Low power Rocker arm clearance adjustment (see page 18)

Cultivator tines bound with dirt or grass Stop the unit, switch the On/Off Stop Control to

STOP, clean and remove any debris binding the tines

CAUSE ACTION

Empty fuel tank Fill fuel tank with new fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Engine is flooded Pull starter rope repeatedly with throttle control fully

engaged and with the choke lever in Position 3

Old fuel Drain gas tank and add fresh fuel

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

On/Off Control is in the OFF (O) position Move switch to ON (I)

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN UNDER LOAD

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take unit to a Troy-Bilt or other qualified service dealer

for

an adjustment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Spark plug gap is too small/close Adjust gap to 0.025”

UNIT OCCASIONALLY HESITATES AT HIGH SPEEDS

SIGNS OF OIL AROUND OIL FILL PLUG/DIPSTICK

SPECIFICATIONS

ENGINE*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 4-Cycle

Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 cu. in. (26.2 cc)

Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,000-3,600 rpm

Operating RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,200-8,800 rpm

Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centrifugal

Ignition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic

On/Off Stop Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positive On/Off Switch

Valve clearance (intake and exhaust) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.003–0.006 in. (0.076–0.0152 mm)

Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 inch (0.655 mm)

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAE 30 Oil

Crankcase Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.04 oz (90 ml)

Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded

Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diaphragm, All-Position

Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Auto Rewind

Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baffled with Guard

Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring Return

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 oz (444 ml)

CULTIVATOR*

Cultivating Path Width (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 inches (22.86 cm)

Cultivating Depth (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 inches (15.24 cm)

Approximate Weight (no fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 lb. (11.5 kg)

La page charge ...