MTD TB144 Manuel utilisateur

Catégorie
Outils de jardin
Taper
Manuel utilisateur
P/N 769-02190 (1/06)
CAUTION: Before using
this product, read this
manual and follow all
safety rules and operating
instructions.
Operator’s Manual
4-Cycle Garden
Cultivator
TB144
2
INTRODUCTION
TABLE OF CONTENTS
Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3
Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7
Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . .8
Starting/Stopping Instructions . . . . . . . . . . . . . . . .10
Operating Instructions . . . . . . . . . . . . . . . . . . . . . .11
Maintenance and Repair Instructions . . . . . . . . . . .12
Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .18
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CARB / EPA Warranty Information . . . . . . . . . . . . .21
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . E22-E24
SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the
states of California, Maine, Oregon and Washington.
All U.S. Forest Land and the state of California (Public
Resources Codes 4442 and 4443), Oregon and
Washington require, by law that certain internal
combustion engines operated on forest brush and/or
grass-covered areas be equipped with a spark arrestor,
maintained in effective working order, or the engine be
constructed, equipped and maintained for the prevention
of fire. Check with your state or local authorities for
regulations pertaining to these requirements. Failure to
follow these requirements could subject you to liability or
a fine. This unit is factory equipped with a spark
arrestor. If it requires replacement, ask your LOCAL
SERVICE DEALER to install the Accessory Part
#180890 Spark Arrestor Kit.
WARNING
THE ENGINE EXHAUST FROM THIS
PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
CALIFORNIA PROPOSITION 65 WARNING
3
RULES FOR SAFE OPERATION
READ ALL INSTRUCTIONS
BEFORE OPERATING
Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
All guards and safety attachments must be installed
properly before operating the unit.
Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace parts that are cracked,
chipped, or damaged in any way. Do not operate the
unit with loose or damaged parts.
Carefully inspect the area before starting the unit.
Remove all debris and hard or sharp objects such as
glass, wire, etc.
Be aware of the risk of injury to the head, hands and
feet.
Clear the area of children, bystanders, and pets. At a
minimum, keep all children, bystanders, and pets
outside a 50 feet (15 m.) radius; there still may be a
risk to bystanders from thrown objects. Bystanders
should be encouraged to wear eye protection. If you
are approached, stop the unit immediately.
Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
Store fuel only in containers specifically designed and
approved for the storage of such materials.
Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
SYMBOL MEANING
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
NOTE: Advises you of information or instructions vital to
the operation or maintenance of the equipment.
SYMBOL MEANING
When using the unit,
you must follow the
safety rules. Please read these instructions
before operating the unit in order to ensure
the safety of the operator and any bystanders.
Please keep these instructions for later use.
WARNING:
• IMPORTANT SAFETY INSTRUCTIONS •
Failure to obey a
safety warning can
result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock and
personal injury.
WARNING:
Failure to obey a
safety warning will
result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock and
personal injury.
DANGER:
Failure to obey a
safety warning may
result in property damage or personal injury
to yourself or to others. Always follow the
safety precautions to reduce the risk of fire,
electric shock and personal injury.
CAUTION:
Indicates
danger,
warning or caution. Attention is required in
order to avoid serious personal injury. May
be used in conjunction with other symbols
or pictographs.
SAFETY ALERT:
Gasoline is highly
flammable, and its
vapors can explode if ignited. Take the
following precautions:
WARNING:
Read the Operator’s Manual(s) and follow all
warnings and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.
4
Do not touch the engine or muffler. These parts get
extremely hot from operation. They remain hot for a
short time after you turn off the unit.
Do not operate the engine faster than the speed
needed to cultivate. Do not run the engine at high
speed when you are not cultivating.
Always stop the engine when cultivating is delayed or
when walking from one cultivating location to another.
If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage. Do not operate before repairing damage. Do
not operate the unit with loose or damaged parts.
Stop and switch the engine to off for maintenance,
repair, or to install or remove the tines.
Use only original equipment manufacturer
replacement parts and accessories for this unit. These
are available from your authorized service dealer. Use
of any unauthorized parts or accessories could lead to
serious injury to the user, or damage to the unit, and
void your warranty.
Keep unit clean of vegetation and other materials.
They may become lodged between the tines and
guard.
To reduce fire hazard, replace faulty muffler and spark
arrestor, keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
OTHER SAFETY WARNINGS
Never store the unit, with fuel in the tank, inside a
building where fumes may reach an open flame or
spark.
Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
Store the unit in a dry area, locked up or up high
to prevent unauthorized use or damage, out of the
reach of children.
Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use. See the Cleaning and Storage
instructions.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE
INSTRUCTIONS
Always stop the engine and allow it to cool before filling
the fuel tank. Never remove the cap of the fuel tank, or
add fuel, when the engine is hot. Never operate the unit
without the fuel cap securely in place. Loosen the fuel
tank cap slowly to relieve any pressure in the tank.
Add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Slowly remove the fuel
cap only after stopping engine. Do not smoke while
fueling or mixing fuel. Wipe up any spilled fuel from the
unit immediately. Always wipe unit dry before using.
Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke or allow sparks and open flames near the area
while adding fuel or operating the unit.
WHILE OPERATING
Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate
this unit only in a well ventilated outdoor area.
Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards. Also wear
ear/hearing protection when operating this unit. Wear
a face or dust mask if the operation is dusty. Long
sleeve shirts are recommended.
Wear heavy, long pants, boots and gloves. Do not
wear loose clothing, jewelry, short pants, sandals or
go barefoot. Secure hair above shoulder level.
This unit has a clutch. The tines remains stationary
when the engine is idling. If it does not, have the unit
adjusted by an authorized service technician.
Be sure the tines are not in contact with anything
before starting the unit.
Use the unit only in daylight or good artificial light.
Avoid accidental starting. The operator and unit must
be in a stable position while starting. See
Starting/Stopping Instructions.
Use the right tool. Only use this tool for the purpose
intended.
Use extreme caution when reversing or pulling the unit
towards you.
Do not overreach. Always keep proper footing and
balance. Take extra care when working on steep
slopes or inclines.
Always hold the unit with both hands when operating.
Keep a firm grip on the grips.
Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the tines
when they are rotating.
RULES FOR SAFE OPERATION
5
SYMBOL MEANING
SAFETY ALERT SYMBOL
Indicates danger, warning, or
caution. May be used in conjunction
with other symbols or pictographs.
WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the
operator and/or bystanders.
WEAR EYE AND HEARING
PROTECTION
WARNING:Thrown
objects and loud noise can cause
severe eye injury and hearing loss.
Wear eye protection meeting ANSI
Z87.1-1989 standards and ear
protection when operating this unit.
Use a full face shield when needed.
KEEP BYSTANDERS AWAY
WARNING:Keep all
bystanders, especially children and
pets, at least 50 feet (15 m.) from the
operating area.
UNLEADED FUEL
Always use clean, fresh unleaded fuel.
OIL
Refer to operator's manual for the
proper type of oil.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
THROWN OBJECTS AND
ROTATING CUTTER CAN CAUSE
SEVERE INJURY
WARNING:Do not
operate without the proper guards in
place. Keep away from the rotating
tines.
ON/OFF STOP CONTROL
ON / START / RUN
ON/OFF STOP CONTROL
OFF or STOP
• CHOKE CONTROL
1 • FULL choke position.
2 • PARTIAL choke position.
3 • RUN position.
HOT SURFACE WARNING
Do not touch a hot muffler or
cylinder. You may get burned. These
parts get extremely hot from
operation. When turned off they
remain hot for a short time.
GARDEN CULTIVATORS –
ROTATING TINES CAN CAUSE
SEVERE INJURY
WARNING:Stop the
engine and allow the tines to stop
before installing or removing tines,
or before cleaning or performing any
maintenance. Keep hands and feet
away from rotating tines.
RULES FOR SAFE OPERATION
12
3
6
KNOW YOUR UNIT
Tine Guard
Cultivator
Tines
Primer Bulb
Muffler
Handlebar
Knob
Starter Rope Grip
Handlebar
Throttle
Control
Choke
Control
Edger
Wheel
Edger
Blade
STOP/OFF (O)
START/ON (I)
Wheel Support
Bracket
Front Handle
Applications
Cultivating sod and light to medium soil
Cultivating in garden areas, around trees, etc.
Edging
KNOW YOUR CULTIVATOR
7
ASSEMBLY INSTRUCTIONS
NOTE: Before setting up your cultivator / edger,
disconnect the spark plug wire from the spark
plug.
POSITIONING THE HANDLEBARS
1. Loosen the two knobs on the inside of the
handlebars (Fig. 1).
2. With the unit upright, swing the handlebars up into
the operating position (Fig. 1).
NOTE: Take care not to pinch the throttle cable or
switch wires when positioning the handlebar.
3. Tighten the knobs to secure the handlebars in place.
NOTE: Do not over-tighten the knobs.
4. Reconnect the spark plug wire to the spark plug.
ADJUSTING TINE DEPTH
To adjust the wheel support bracket proceed as follows:
1. Stop engine and disconnect spark plug to avoid
accidental starting.
2. Remove cotter pin from the clevis pin and slide clevis
pin out of tailpiece bracket (Fig. 3).
3. Slide the wheel support bracket up or down in the
tailpiece, aligning the holes to the desire height.
4. Place the clevis pin through the hole and secure with
cotter pin.
ATTACHING THE EDGER WHEEL AND
BLADE
To convert the cultivator to an edger proceed as follows:
1. Push the On/Off switch to Off (O) position to stop
engine and tines and disconnect spark plug to avoid
accidental starting.
NOTE: It may be necessary to lay the cultivator / edger
back in a horizontal position on a flat level surface
with the upper handle touching the ground.
2. Remove the click pin from each end of the tine shaft
and slide the tines off the shaft.
3. Slide the edger wheel, with the hub facing inward,
onto the right side of the tine shaft and secure with
the click pin in the inside hole (Fig. 4).
4. Slide the edger blade with the hub facing out onto
the left side of tine shaft and secure with the click pin
in the inside hole (Fig. 4).
5. The edger guide line indicates where cutting will
occur. Guide the unit along a flowerbed, sidewalk, or
driveway so the edger guide line is above the desired
line of cut.
Clevis Pin
Cotter Pin
Wheel
Support
Bracket
Tailpiece Bracket
Fig. 3
Fig. 4
Edger Guide
Line
Click Pin
Hub
Edger Blade
Edger Wheel
Fig. 1
Handlebar
Knob
Handlebars
Washer
Hole
Bolt
Fig. 2
Tine Shaft
8
OIL AND FUEL INFORMATION
RECOMMENDED OIL TYPE
Using the proper type and weight of oil in
the crankcase is extremely important.
Check the oil before each use and change
the oil regularly. Using incorrect or dirty oil can cause
premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American
Petroleum Institute) service class SF, SG, SH.
ADDING OIL TO CRANKCASE: INITIAL USE
NOTE: This unit is shipped without oil in the crankcase.
In order to avoid damage to the unit, put oil in
the crankcase before attempting to start unit.
Your unit is supplied with one 3.04 fluid oz. (90 ml.)
bottle of SAE 30 SF, SG, SH oil (Fig. 5).
NOTE: Save the bottle to measure the correct amount
for future oil changes. See Changing the Oil.
NOTE:
Your new 4-Cycle cultivator is shipped for
operation in conditions above 40°F (4°C). For
cold weather operation, where temperatures
fall below 40°F (4°C), use a high-quality SAE
10W30 weight oil of API (American Petroleum
Institute) service class SF, SG, SH.
1. Unscrew the oil bottle top and remove the paper seal
covering the opening. Replace the top and cut the
tip off the funnel spout (Fig. 5).
2. Place the unit on a flat level surface with the
cultivator in a horizontal position (Fig. 6).
3. Remove the oil plug / dipstick from the crankcase
(Fig. 7).
4. Pour the entire bottle of oil into the oil fill hole
(Fig. 8).
NOTE: Never add oil to the fuel or fuel tank.
5. Wipe up any oil that may have spilled and reinstall
the oil fill plug / dipstick.
The importance of checking and maintaining the proper
oil level in the crankcase cannot be overemphasized.
Check oil before each use and change as specified in
the Maintenance Schedule.
Fig. 5
Fig. 7
Funnel Spout
Fig. 8
Oil Fill
Fig. 6
Oil Fill Plug/Dipstick
Oil Fill
Plug/Dipstick
Oil Fill Hole
O-Ring
OVERFILLING OIL
CRANKCASE MAY
CAUSE PRODUCT DAMAGE. Check and
maintain the proper oil level in the crank
case; it is important and cannot be
overemphasized. Check the oil before each
use and change it as needed. See Changing
the Oil.
CAUTION:
9
Add fuel in a clean,
well ventilated
outdoor area. Wipe up any spilled fuel
immediately. Avoid creating a source of
ignition for spilt fuel. Do not start the engine
until fuel vapors dissipate.
WARNING:
Gasoline is
extremely
flammable. Ignited Vapors may explode.
Always stop the engine and allow it to cool
before filling the fuel tank. Do not smoke
while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING:
Remove fuel cap
slowly to avoid injury
from fuel spray. Never operate the unit
without the fuel cap securely in place
.
WARNING:
RECOMMENDED FUEL TYPE
Old fuel is the primary reason for improper
unit performance. Be sure to use fresh,
clean, unleaded gasoline.
NOTE: This is a four cycle engine. In order to avoid
damage to the unit, do not mix oil with gasoline.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and
oxygenates such as ethanol, methanol or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel form acids when stored.
When using alcohol-blended fuel, use fresh fuel that is
less than 60 days old.
Using Blended Fuels
If you choose to use a blended fuel, or if its use is
unavoidable, follow recommended precautions:
Always use fresh unleaded gasoline
Use Sta-Bil
®
or an equivalent
Drain tank and run the engine dry before storing unit
Using Fuel Additives
The use of fuel additives, such as Sta-Bil
®
or an
equivalent, will inhibit corrosion and minimize the
formation of gum deposits. Using a fuel additive can
keep fuel from forming harmful deposits in the
carburetor for up to six (6) months. Add 0.8 oz. (23 ml.)
of fuel additive per gallon of fuel to an approved gas
container according to the instructions on the container.
NEVER add fuel additives directly to the unit's gas tank.
OIL AND FUEL INFORMATION
FUELING THE UNIT
NOTE: Fill or add fuel to the tank only when the
cultivator is in a horizontal position (Fig. 9).
1. Remove fuel cap. Remove the tag from the fuel tank
neck.
2. Place spout of gas container into the fill hole on the
fuel tank and fill tank.
NOTE: Do not overfill tank.
3. Wipe up any gasoline that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least 30 ft. (9.1 m) from the fueling
source and site before starting the engine.
NOTE: Dispose of the old gasoline in accordance to
Federal, State and Local regulations.
Fig. 9
Fuel Cap
10
STARTING/STOPPING INSTRUCTIONS
1. Check the oil level in the crankcase. Refer to
Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline.
Refer to Fueling the Unit.
3. Put the On/Off Stop Control in the ON [
I
] position
(Fig. 10).
4. Place the choke lever in Position 1 (Fig. 11).
5. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in the
primer bulb and fuel lines (Fig. 11). If you can’t see
fuel in the bulb, press and release the bulb as many
times as it takes before you can see fuel in it.
6. Hold the throttle and handlebar with one hand and
grab the starter rope with your other hand. Use your
foot to hold down the cultivator (Fig. 12).
NOTE: Tilt the unit back slightly to bring the tines off the
ground when starting.
7. While squeezing the throttle control, pull the starter
rope with a smooth and steady pull. Repeat this 5
times.
8. Move the choke lever to Position 2.
9. While squeezing the throttle control, pull the starter
rope in the same manner as explained in Step 7. Pull
1 to 3 times to start the engine.
10. Keep the throttle squeezed and allow the engine to
warm up for 15 to 30 seconds.
11. Place the choke lever in Position 3. Release the
throttle control to the idle position and begin
operation.
IF... The engine does not start, repeat Steps 4 - 11.
IF... The engine fails to start after a few attempts, place
the choke lever in Position 3 and squeeze the
throttle control. Pull the starter rope 3 to 8 times.
The engine should start. If not, continue pulling
starter rope until the engine starts.
IF WARM... If the engine is already warm, make sure
the On/Off Stop control is in the ON position and
start the unit with the choke lever in Position 2. After
the unit starts, move the choke lever to Position 3.
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control. Allow the
engine to cool down by idling.
2. Put the On/Off Stop Control in the OFF (O) position.
STARTING INSTRUCTIONS
Primer Bulb
Choke Lever
Fig. 12
Fig. 10
Throttle
Control
ON (I)
Fig. 11
Operate this unit only
in a well- ventilated
outdoor area. Carbon monoxide exhaust fumes
can be lethal in a confined area.
WARNING:
Avoid accidental
starting. Make sure
you are in the starting position when pulling
the starter rope (Fig. 12).
To avoid serious
injury, the operator and unit must be in a stable
position while starting.
WARNING:
OFF (O)
Position 3
Position 1
Position 2
11
OPERATING INSTRUCTIONS
TRANSPORTING THE UNIT
1. Stop the engine.
2. Tilt the unit back until the tines clear the ground.
3. Push or pull the unit to the next location to be
cultivated.
Fig. 13
OPERATING TIPS
1. Move the cultivator to the work area prior to starting
the engine. Transport the cultivator by pushing or
pulling it along on its wheels.
2. Start the unit by following the Starting Instructions.
3. With the engine running and the tines off the ground,
depress the throttle control to increase the engine
speed.
4. While holding the upper handle with both hands,
slowly lower the cultivator until the tines make
contact with the ground (Fig. 13).
5. As cultivating action begins, tilt the cultivator up
slightly using the handle so that the tines can
penetrate the ground.
6. Once the ground has been broken, continue at a
moderate pace until you are familiar with the controls
and the handling of the cultivator.
7. If the tines are digging too deep or not deep enough,
adjust the wheel bracket as described in Adjusting
Tine Depth.
To prevent serious
personal injury, use
extreme caution when reversing
or pulling the unit towards you.
WARNING:
To prevent serious
personal injury,
never pick-up or carry the unit while the
engine is running.
WARNING:
To prevent serious
personal injury,
always stop the engine when operation is
delayed or when transporting the unit from
one location to another
WARNING:
Dress properly to
reduce the risk of
injury when operating this unit. Do not
wear loose clothing or jewelry. Wear eye
and ear/hearing protection. Wear heavy
long pants, boots and gloves. Do not wear
short pants, sandals or operate barefoot.
WARNING:
12
MAINTENANCE AND REPAIR INSTRUCTIONS
Click Pin
“A” Tine
Fig. 14
TINE REMOVAL AND REPLACEMENT
All 4 tines should be replaced at the same time because
they will wear evenly through normal use. Work on one
side at a time.
1. Put the On/Off Stop Control in the STOP (O) position
and disconnect the spark plug wire.
NOTE: It may be necessary to lay the cultivator back in a
horizontal position on a flat level surface with the
upper handle touching the ground.
2. Remove the click pin from each end of the tine shaft.
Slide the tines off of the shaft (Fig. 14).
3. Clean and oil the shaft.
4. Slide on the new tines with the hubs facing out. The
four tines are marked with the letters “A” or “B.”
“B” Tine
Hubs
To prevent serious
personal injury,
always wear heavy gloves when handling
the tines.
WARNING:
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should
also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures, take your unit to a Troy-Bilt or
other qualified service dealer. Call 1-800-520-
5520 for more information.
NOTE: Maintenance, replacement, or repair of the
emission control devices and system may be
performed by a Troy-Bilt or other qualified service
dealer. Call 1-800-520-5520 for more information.
FREQUENCY MAINTENANCE REQUIRED REFER TO
Before starting engine
Fill fuel tank with fresh fuel
Check oil
Page 9
Page 13
Every 10 hours Clean and re-oil air filter Page 14
First change at 10 hours
Every 25 hours thereafter
Every 25 hours
Change oil
Change oil
Clean spark arrestor
Page 13
Page 13
Page 17
Every 25 hours Check spark plug condition and gap Page 17
To prevent serious
injury, never perform
maintenance or repairs with unit running.
Always service and repair a cool unit.
Disconnect the spark plug wire to ensure that
the unit cannot start.
WARNING:
5. Place one “A” tine and one “B” tine onto the shaft.
6. Secure the new tines to the shaft with click pins. It
may be necessary to wash the dirt off the tines and
shaft for ease of removal.
13
MAINTENANCE AND REPAIR INSTRUCTIONS
CHECKING THE OIL LEVEL
The importance of checking and maintaining the proper
oil level in the crankcase cannot be overemphasized.
Check oil before each use:
1. Stop the engine and allow oil to drain into the crankcase.
2. Place the unit on a flat, level surface to get a proper
oil level reading (Fig. 9).
3. Keep dirt, grass clippings and other debris out of the
engine. Clean the area around the oil fill plug/dipstick
before removing it.
4. Remove the oil fill plug/dipstick and wipe off oil.
Reinsert it all the way back in.
5. Remove the oil fill plug/dipstick and check the oil level.
Oil should be up to the top of the dipstick (Fig. 15).
6. If the level is low, add a small amount of oil to the oil
fill hole and recheck (Fig. 16). Repeat this procedure
until the oil level reaches the top of the dipstick.
NOTE: Do not overfill the unit.
Top of Dipstick
O-Ring
Oil Fill Plug/Dipstick
CHANGING THE OIL
For a new engine, change the oil after the first 10 hours of
operation. Change the oil while the engine is still warm. The
oil will flow freely and carry away more impurities.
1. Unplug spark plug wire to prevent accidental starting.
2. Remove the oil fill plug/dipstick.
3. Pour the oil out of the oil fill hole and into a container
by tipping the unit to a vertical position (Fig. 17).
Allow ample time for complete drainage.
Fig. 17
Fig. 15
Fig. 16
NOTE: Make sure the O-ring is in place on the oil fill
plug/dipstick when checking and changing the
oil (Fig. 16).
Full
Add 1.4-1.5 Oz.
(41-44 ml)
6. Replace the oil fill plug/dipstick.
7. Reconnect the spark plug wire.
4. Wipe up any oil residue on the unit and clean up any
oil that may have spilled. Dispose of the oil
according to Federal, State and local regulations.
5. Refill the crankcase with 3.04 fluid ounce (90 ml) of
SAE 30 SF, SG, SH oil.
NOTE: Use the bottle and spout saved from initial use to
measure the correct amount of oil. Pour fresh
fuel into the bottle and fill it to the top of the
label. The top of the label on the bottle measures
approximately 3.04 ounces (90 ml). Check the level
with the dipstick. If the level is low, add a small
amount of oil and recheck. Do not overfill (Fig. 18).
Fill Level
Fig. 18
Wear gloves to
prevent injury when
handling the unit.
CAUTION:
To prevent extensive
engine wear and
damage to the unit, always maintain the
proper oil level in the crankcase. Never
operate the unit with the oil level below the
bottom of the dipstick.
CAUTION:
Oil Fill Plug/Dipstick
Oil Fill Hole
O-Ring
14
MAINTENANCE AND REPAIR INSTRUCTIONS
AIR FILTER MAINTENANCE
Cleaning the Air Filter
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Failure to maintain
your air filter properly can result in poor performance or
can cause permanent damage to your engine.
1. Open the air filter cover. Push the tab on the left side
of the cover in, swing the air filter cover out and off
the air filter housing (Fig. 19).
2. Remove the air filter and the screen that sits
behind it (Fig. 19).
3. Wash the filter in detergent and water (Fig. 20). Rinse
the filter thoroughly and allow it to dry.
4. Apply enough clean SAE 30 motor oil to lightly coat
the filter (Fig. 21).
Fig. 20
5. Squeeze the filter to spread and remove excess oil
(Fig. 21).
6. Replace the filter (Fig. 19).
NOTE: If the unit is operated without the air filter, you
will VOID the warranty.
7. Reinstall the air filter cover. Position the hooks on
the right side of the air filter cover into the slots at
the right side of the air filter housing.
8. Swing the cover to the left until the tab on the air
filter cover snaps into place in the slot on the left
side of the air filter housing (Fig. 18).
CARBURETOR ADJUSTMENT
The idle speed of the engine is adjustable. An idle
adjustment screw is reached though a hole in the top of
the engine cover (Fig. 22).
NOTE: Careless adjustments can seriously damage your
unit. For carburetor adjustments, take your unit
to a Sears or other qualified service dealer.
Check Fuel
Old fuel is usually the reason for improper unit
performance. Drain and refill the tank with fresh fuel prior
to making any adjustments. Refer to Oil and Fuel
Information.
Clean Air Filter
The condition of the air filter is important to the operation
of the unit. A dirty air filter will restrict air flow. This is
often mistaken for an out of adjustment carburetor.
Check the condition of the air filter before adjusting the
idle speed screw. Refer to Air Filter Maintenance.
Air Filter
Air Filter
Screen
Hooks
Slot
Choke Lever
Air Filter Cover
Air Filter Housing
Tab
Tab
Fig. 19
Adjust Idle Speed Screw
If, after checking the fuel and cleaning the air filter, the
engine still will not idle, adjust the idle speed screw as
follows:
1. Start the engine and let it run at a high idle for a minute
to warm up. Refer to Starting/Stopping Instructions.
This unit needs to
run during idle
speed adjustment. Wear protective clothing
and observe all safety instructions to
prevent serious personal injury.
WARNING:
To avoid serious
personal injury,
always turn the unit off and allow it to cool
before you clean or service it.
WARNING:
Fig. 21
15
MAINTENANCE AND REPAIR INSTRUCTIONS
3. Disconnect the spark plug wire.
4. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning it
counterclockwise with a 5/8” socket.
5. Remove the engine cover.
NOTE: To ease engine cover removal, pull the starter
rope out a little to give some slack.
6. Clean dirt from around the rocker arm cover.
Remove the screw holding the rocker arm cover with
a large flat blade screwdriver or Torx T-25 bit
(Fig. 27). Remove the rocker arm cover and gasket.
Rocker Arm Cover
Fig. 27
Spark Plug Hole
Gasket
Remove
Screws
Engine Cover
Fig. 25
Muffler
ROCKER ARM CLEARANCE
The rocker arm clearance may need adjustment if your
unit suffers a loss of performance power or has trouble
starting. Adjusting the rocker arm clearance requires
disassembly of the engine. If you feel unsure or
unqualified to perform this, take the unit to a Sears or
other qualified service dealer.
NOTE: Inspect the valve to rocker arm clearance with a
feeler gauge after the first 10 hours of operation
and then every 25 hours of operation thereafter.
The engine must be cold when checking or adjusting
the valve clearance.
This task should be performed inside, in a clean,
dust free area.
To adjust the rocker arm clearance:
1. Remove the two (2) screws on top of the engine cover
with a Flat-head or T-25 Torx screwdriver (Fig. 25).
2. Remove the screw behind the engine cover (Fig. 26).
Top View Of The Engine
Screw
Fig. 26
1
23
Idle Adjustment Screw
Checking the fuel, cleaning the air filter, and adjusting
the idle speed should solve most engine problems. If not
and all of the following are true:
the engine will not idle
the engine hesitates or stalls on acceleration
there is a loss of engine power
Have the carburetor adjusted by a Troy-Bilt or other
qualified service dealer.
Fig. 22
NOTE: Ensure the tines are not in contact with the
ground when adjusting the idle.
2. Release the throttle trigger and let the engine idle. If the
engine stops, insert a small phillips or flat blade
screwdriver into the hole in the air filter/muffler cover
(Fig. 22). Turn the idle speed screw in, clockwise, 1/8 of
a turn at a time (as needed) until the engine idles
smoothly.
NOTE: The tines should not rotate when the engine idles.
3. If the tines rotate when the engine idles, turn the idle
speed screw counterclockwise 1/8 of a turn at a time
(as needed), to reduce idle speed.
16
7. Pull the starter rope slowly to bring the piston to the top
of its travel, (known as top dead center). Check that:
The piston is at the top of its travel while looking in
the spark plug hole (Fig. 27)
Both rocker arms move freely, and both valves are
closed
If these statements are not true, repeat this step.
8. Slide the feeler gauge between the rocker arm and
the valve return spring. Measure the clearance
between the valve stem and rocker arm (Fig. 29).
Measure both the intake and exhaust valves.
Adjusting Nuts
Feeler Gauge
Rocker Arms
Fig. 28
Fig. 29
The recommended clearance for both intake and
exhaust is 0.003 – 0.006 in. (0.076 – 0.152 mm). Use a
standard automotive 0.005 in. (0.127 mm) feeler gauge.
The feeler gauge should slide between the rocker arm
and valve stem with a slight amount of resistance,
without binding. See Figure 28 and 29.
9. If the clearance is not within specification:
a. Turn the adjusting nut using a 5/16 inch (8 mm)
wrench or nut driver (Fig. 29).
To increase clearance, turn the adjusting nut
counterclockwise.
To decrease clearance, turn the adjusting nut
clockwise.
b. Recheck both clearances, and adjust as necessary.
10. Reinstall the rocker arm cover using a new gasket.
Torque the screw to 20–30 in
lb (2.2–3.4 Nm).
11. Reinstall the engine cover. Check alignment of the
cover before tightening the screws. Tighten screws.
12. Check the spark plug and reinstall. See Replacing
the Spark Plug.
13. Replace the spark plug wire.
INTAKE
EXHAUST
Feeler Gauge
Adjusting Nut
Rocker Arm
0.003–0.006 in.
(0.076–0.152 mm)
Valve Stem
MAINTENANCE AND REPAIR INSTRUCTIONS
17
0.025 in.
(0.655 mm.)
REPLACING THE SPARK PLUG
Use a replacement Champion RDZ19H spark plug. The
correct air gap is 0.025 in. (0.655 mm.). Remove the plug
after every 25 hours of operation and check its
condition.
1. Stop the engine and allow it to cool. Grasp the plug
wire firmly and pull the cap from the spark plug.
2. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning it
counterclockwise with a 5/8” socket.
3. Replace cracked, fouled or dirty spark plug. Set the air
gap at 0.025 in. (0.655 mm.) using a feeler gauge (Fig. 23).
Fig. 23
4. Install a correctly-gapped spark plug in the cylinder
head. Turn the 5/8 in. socket clockwise until snug.
If using a torque wrench torque to:
110-120 in.•lb. (12.3-13.5 N•m)
Do not over tighten.
Fig. 24
Muffler
Spark Arrestor Screen
Spark Arrestor Cover
Screw
Tab
Slot
SPARK ARRESTOR MAINTENANCE
1. Remove the muffler cover. See Rocker Arm Clearance.
2. With a flat blade screwdriver or Torx T-20 bit,
remove the screw attaching the spark arrestor cover
to the muffler (Fig. 24).
3. Pull the tab on the spark arrestor cover out of the
muffler. Remove the spark arrestor cover.
4. Remove the spark arrestor screen from the spark
arrestor cover.
5. Clean the spark arrestor screen with a wire brush or
replace it.
6. Reinstall the spark arrestor screen, spark arrestor
cover and screw.
Do not sand blast,
scrape or clean
electrodes. Grit in the engine could damage
the cylinder.
WARNING:
MAINTENANCE AND REPAIR INSTRUCTIONS
18
MAINTENANCE AND REPAIR INSTRUCTIONS
Cleaning the Unit
Use a small brush to clean off the outside of the unit
and to keep the air vents free of obstructions.
Do not use strong detergents or petroleum based
cleaners, such as kerosene. Some household
cleaners contain aromatic oils such as pine and
lemon that can damage the plastic housings or
handles. Wipe off any moisture with a soft cloth.
Storage
Never store the unit with fuel in the tank where
fumes may reach an open flame or spark.
Allow the engine to cool before storing.
Store the unit in a locked up area to prevent
unauthorized use or damage.
Store the unit in a dry, well-ventilated area. Do not
store next to corrosive material like fertilizer.
Store the unit out of the reach of children.
Long Term Storage
If the unit will be stored for an extended time:
1. Carefully drain all gasoline from the fuel tank by
removing the fuel cap and tipping the motor housing
over to allow the fuel to drain into an approved gas
container. Do not use gas that has been stored for
more than 60 days. Dispose of the old gasoline in
accordance with Federal, State and Local
regulations.
2. Start the engine and allow it to run until it stalls. This
ensures that all gasoline has been drained from the
carburetor.
3. Allow the engine to cool. Remove the spark plug and
put 1 oz. (30 ml) of high quality motor oil into the
cylinder. Pull the starter rope slowly to distribute the
oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil
from the cylinder before attempting to start the
unit after storage.
4. Change the oil, referring to the Changing the Oil
section. Dispose of the old oil in accordance with
Federal, State and Local regulations.
5. Thoroughly clean the unit and inspect for any loose
or damaged parts. Repair or replace damaged parts
and tighten loose screws, nuts or bolts.
6. To take up less storage area, loosen the handlebar
knobs and fold the handlebar down. The unit is
ready for storage.
Transporting
Allow the engine to cool before transporting.
Secure the unit while transporting.
Drain the fuel tank before transporting.
Tighten fuel cap before transporting.
To avoid serious
personal injury,
always turn the unit off and allow it to cool
before you clean or perform any
maintenance on it.
WARNING:
19
TROUBLESHOOTING
NOTE: For repairs beyond the minor adjustments listed above, contact your nearest Troy-Bilt Parts &
Repair center (1-800-520-5520) or other qualified service dealer for an adjustment.
CAUSE ACTION
Oil fill plug/dipstick loose or missing o-ring Tighten oil fill plug/dipstick, replace o-ring
CAUSE ACTION
Old fuel Drain gas tank and add fresh fuel
Improper carburetor adjustment Take unit to a Troy-Bilt or other qualified service dealer for
an adjustment
Fouled spark plug Replace or clean the spark plug
Plugged spark arrestor Clean or replace spark arrestor
Low power Rocker arm clearance adjustment (see page 18)
Cultivator tines bound with dirt or grass Stop the unit, switch the On/Off Stop Control to
STOP, clean and remove any debris binding the tines
CAUSE ACTION
Empty fuel tank Fill fuel tank with new fuel
Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times
Engine is flooded Pull starter rope repeatedly with throttle control fully
engaged and with the choke lever in Position 3
Old fuel Drain gas tank and add fresh fuel
Fouled spark plug Replace or clean the spark plug
Plugged spark arrestor Clean or replace spark arrestor
On/Off Control is in the OFF (O) position Move switch to ON (I)
ENGINE WILL NOT START
ENGINE WILL NOT IDLE
ENGINE WILL NOT ACCELERATE
ENGINE LACKS POWER OR STALLS WHEN UNDER LOAD
CAUSE ACTION
Air filter is plugged Replace or clean the air filter
Old fuel Drain gas tank and add fresh fuel
Improper carburetor adjustment Adjust according to the Carburetor Adjustments section
CAUSE ACTION
Old fuel Drain gas tank and add fresh fuel
Improper carburetor adjustment Take unit to a Troy-Bilt or other qualified service dealer
for
an adjustment
Dirty air filter Clean or replace the air filter
Plugged spark arrestor Clean or replace spark arrestor
CAUSE ACTION
Spark plug gap is too small/close Adjust gap to 0.025”
UNIT OCCASIONALLY HESITATES AT HIGH SPEEDS
SIGNS OF OIL AROUND OIL FILL PLUG/DIPSTICK
20
SPECIFICATIONS
ENGINE*
*All specifications are based on the latest product information available at the time of printing. We reserve the right to
make changes at any time without notice.
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 4-Cycle
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 cu. in. (26.2 cc)
Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,000-3,600 rpm
Operating RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,200-8,800 rpm
Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centrifugal
Ignition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic
On/Off Stop Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positive On/Off Switch
Valve clearance (intake and exhaust) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.003–0.006 in. (0.076–0.0152 mm)
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 inch (0.655 mm)
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAE 30 Oil
Crankcase Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.04 oz (90 ml)
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded
Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diaphragm, All-Position
Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Rewind
Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baffled with Guard
Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring Return
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 oz (444 ml)
CULTIVATOR*
Cultivating Path Width (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 inches (22.86 cm)
Cultivating Depth (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 inches (15.24 cm)
Approximate Weight (no fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 lb. (11.5 kg)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

MTD TB144 Manuel utilisateur

Catégorie
Outils de jardin
Taper
Manuel utilisateur

dans d''autres langues