ELICA ELG630S2 Guide d'installation

Marque: ELICA

Modèle: ELG630S2

Taper: Guide d'installation

Use, Care, and

Installation Guide

Guide

d’utilisation,

d’entretien et

d’installation

Guía de

instalación, uso y

mantenimiento

READ AND SAVE THESE

INSTRUCTIONS

LISEZ CES

INSTRUCTIONS ET

CONSERVEZ-LES

LEA Y CONSERVE

ESTAS INSTRUCCIONES

LI3B9D

Printed in Mexico

Models:

ELG630S2

ELG636S2

ENGLISH

Contents

Important safety notice................................................................................................................................................................................................. 3

Electrical & Installation requirements ................................................................................................................................................................ 4

Before installing the hood ...................................................................................................................................................................................... 4

Dimensions and Clearances......................................................................................................................................................................................... 4

List of Materials................................................................................................................................................................................................................. 5

Parts supplied .............................................................................................................................................................................................................. 5

Parts not supplied ...................................................................................................................................................................................................... 5

Ducting Options and Examples.................................................................................................................................................................................. 6

Installation (Ducted version)....................................................................................................................................................................................... 6

Installation (Recirculating version)........................................................................................................................................................................... 9

Description of the hood................................................................................................................................................................................................. 12

Control.................................................................................................................................................................................................................................. 12

Maintenance ...................................................................................................................................................................................................................... 13

Warranty ............................................................................................................................................................................................................................ 15

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Safety Warning: Turn o power circuit at service panel and lock out panel, before wiring this appliance.

Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit

IMPORTANT SAFETY NOTICE

I CAUTION

FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO

EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR

VAPOURS.

I WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

B. Before servicing or cleaning the unit, switch power o

at service panel and lock service panel disconnecting

means to prevent power from being switched on

accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

C. Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable

codes & standards, including ﬁre-rated construction.

D. Sucient air is needed for proper combustion and

exhausting of gases through the ﬂue (Chimney) of fuel

burning equipment to prevent back- drafting.

Follow the heating equipment manufacturers guideline

and safety standards such as those published by the

national Fire Protection Association (NFPA), the American

Society For Heating, Refrigeration And Air Conditioning

Engineers (ASHRAE), and the local code authorities.

E. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

F. Ducted systems must always be vented to the outdoors.

I CAUTION

To reduce risk of ﬁre and to properly exhaust air, be sure to

duct air outside - do not vent exhaust air into spaces within

walls, ceilings, attics, crawl spaces, or garages.

I WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT

WORK.

Install this hood in accordance with all requirements speciﬁed.

I WARNING

To reduce the risk of ﬁre or electric shock, do not use this

hood with any external solid state speed control device.

I WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

ﬂambeing food (I.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate

for the size of the surface element.

I WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet,

or other metal tray, then turn o the gas burner or the

electric element. BE CAREFUL TO PREVENT BURNS. If the

ﬂames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - you may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a class ABC extinguisher, and

you already know how to operate it.

2) The ﬁre is small and contained in the area where it

started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit.

Based on “Kitchen Fire Safety Tips” published by NFPA.

OPERATION

Always leave safety grills and ﬁlters in place. Without

these components, operating blowers could catch onto hair,

ﬁngers and loose clothing.

The manufacturer declines all responsibility in the event of

failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The

manufacturer further declines all responsibility for injury due

to negligence and the warranty of the unit automatically

expires due to improper maintenance.

I CAUTION

Automatically Operated Device - To Reduce The Risk Of

Injury Disconnect From Power Supply Before Servicing.

ELECTRICAL & INSTALLATION REQUIREMENTS

IMPORTANT

Observe all governing codes and ordinances.

It is the customer’s responsibility:

đƫ To contact a qualiﬁed electrical installer.

đƫ To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No.0-M91-latest edition**

and all local codes and ordinances.

đƫ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

đƫ Do not ground to a gas pipe.

đƫ Check with a qualiﬁed electrician if you are not sure range

hood is properly grounded.

đƫ Do not have a fuse in the neutral or ground circuit.

IMPORTANT

đƫ Save Installation Instructions for electrical inspector’s use.

đƫ The range hood must be connected with copper wire only.

đƫ The range hood should be connected directly to the fused

disconnect (Or circuit breaker) box through metal

electrical conduit.

đƫ Wire sizes must conform to the requirements of the

National Electrical Code ANSI/NFPA 70 — latest edition*,

or CSA Standards C22.1-94, Canadian Electrical Code Part

1 and C22.2 No. 0-M91 - latest edition** and all local codes

and ordinances.

đƫ A U.L.- or C.S.A.-listed conduit connector must be

provided at each end of the power supply conduit (at the

range hood and at the junction box).

Copies of the standards listed may be obtained from:

* National Fire Protection Association Batterymarch Park Quincy,

Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road Cleveland,

Ohio 44131-5575

BEFORE INSTALLING THE HOOD

1 For the most ecient air ﬂow exhaust, use a straight run

or as few elbows as possible.

CAUTION: Vent unit to outside of building, only.

2 At least two people are necessary for installation.

3 Fittings material is provided to secure the hood to most

types of walls/ceilings, consult a Qualiﬁed Installer,

check if they perfectly ﬁt with your cabinet/wall.

4 Do not use ﬂex ducting.

5 COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air

ﬂow and a nonmetallic thermal break to minimize

conduction of outside temperatures as part of the

ductwork. The damper should be on the cold air side of

the thermal break.

The break should be as close as possible to where the

ducting enters the heated portion of the house.

6 Make up air: Local building codes may require the use of

Make-Up Air Systems when using Ducted Ventilation

Systems greater than speciﬁed CFM of air movement.

The speciﬁed CFM varies from locale to locale. Consult

your HVAC professional for speciﬁc requirements in your

area.

DIMENSIONS AND CLEARANCES

**D

Models

ELG630S2 ELG636S2

A 30” (76 cm) 36” (91.2 cm)

B 19

⁄16” (50 cm)

Max: 42

⁄8” (108.2 cm)

Min: 28

⁄16” (71.9 cm)

D**

Max: 36

⁄16” (93.8 cm)

Min: 24

⁄8” (62.5 cm)

E 6” (15.24 cm)

F 10

⁄4” (27.3 cm)

G 13

⁄16” (33.5 cm)

H 28

⁄8” (73 cm)

I 20

⁄2” (52 cm)

J 5” (12.7 cm)

* Ductless (Recirculating) version

** Ducted version

LIST OF MATERIALS

Removing the packaging.

I CAUTION

Remove carton carefully, Wear gloves to protect against sharp edges.

I WARNING

Remove the protective ﬁlm covering the product before putting into operation.

Supplied Part Pieces Supplied Part Pieces

Hood assembly with blower

Mounting template

5x45 mm

6” round air transition

4.2x8 mm

Duct cover bracket

3.5x9.5 mm

Duct covers

8x40 mm

Parts no supplied

Tools/Materials required

đƫ%.!ƫ*10/

đƫ,!ƫ0+ƫ)+1*0ƫ0!),(0!

đƫćĘƫĨāĆċĂƫ)ĩƫ.+1* ! ƫ)!0(ƫ 10ƫ(!*#0$ƫ0+ƫ/1%0ƫ%*/0((0%+*

đƫ!/1.%*#ƫ0,!

đƫ(%!./

đƫ(+2!/

đƫ*%"!

đƫ"!05ƫ#(//!/

đƫ(!0.%ƫ .%((ƫ3%0$ƫ

⁄16” and

⁄8” Bits

đƫ0.%*ƫ.!(%!"

đƫ,%.%0ƫ(!2!(

đƫ10ƫ0,!

đƫ.!3 .%2!./č

- Phillips (Posidrive) # 2

- Torx # 2

đƫ%.!ƫ100!.ĥ/0.%,,!.

đƫ/'%*#ƫ0,!

đƫ))!.

đƫ3Čƫ&%#ƫ/3ƫ+.ƫ.!%,.+0%*#ƫ/3

Optional Accessories and Consumable Parts

Ductless Recirculating Kit

To be used only in the Ductless (Recirculating) version

includes: charcoal ﬁlter, charcoal ﬁlter support and ﬁxing

bracket, deﬂector.

Ducting options

Closely follow the instructions set out in this manual.

All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this

manual, is declined.

Ducting version Ductless (Recirculating)

The hood is equipped with a 6” (15.2 cm) round transition

for discharge of fumes to the outside.

Roof Venting Wall Venting

A. Roof cap

B. 6” (15.2 cm) round vent

A. Wall cap

B. 6” (15.2 cm) round vent

In cases where it should

not be possible to dis-

charge cooking fumes and

vapour to the outside.

Attach a charcoal filter and

the deflector on the duct

cover support bracket.

Fumes and vapours

are recycled through the

top grille by means of a

duct connected to the

transition and the transition

mounted on the deflector.

For this version only:

purchase the Ductless

Recirculating Kit.

Minimum Duct Size:

6” Round Pipe.

A. Deflector

B. 6” (15.2 cm) round vent

Preparation

Do not cut a joist or stud unless absolutely necessary. If a joist

or stud must be cut, then a supporting frame must be

constructed.

Fittings material is provided to secure the hood to most types

of walls/ceilings.

However, a qualified technician must verify suitability of the

materials in accordance with the type of wall/ceiling.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

Recommended installation height:

Hood installation height above cooktop is the users preference,

as long as the recommended measures has been respected.

The lower the hood is above the cooktop, the more ecient

the capturing of cooking odors, grease and smoke.

I CAUTION

FOR GAS RANGES INSTALLATION: MOUNT THIS HOOD SO

THAT THE BOTTOM EDGE IS AT 30” (76,2 CM) ABOVE THE

COOKING SURFACE.

FOR ELECTRIC RANGES INSTALLATION: MOUNT THIS HOOD

SO THAT THE BOTTOM IS NOT LESS THAN 24” (61 CM) AND

NOT MORE THAT 30” (76,2 CM) ABOVE THE COOKING

SURFACE.

HOUSEHOLD USE. PLEASE, READ INSTALLATION MANUAL

FOR SPECIFIC APPLICATION.

Check your ceiling height and the hood height maximum

before you select your hood.

Installation- Ducted version

đƫ If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall. Otherwise put a thick, protective covering over

countertop, cooktop or range to protect from damage and

debris. Select a ﬂat surface for assembling the unit. Cover

that surface with a protective covering and place all cano-

py hood parts and hardware in it.

đƫ Determine and mark the centerline on the wall where the

canopy hood will be installed.

đƫ Select a mounting height comfortable for the user and

mark on wall.

đƫ Tape template, matching center-line and hood bottom.

Mounting the duct cover bracket

The duct bracket should be installed against the back wall

and flush with the ceiling.

This bracket will hold the telescopic duct cover in place at

the top.

Secure the bracket to the wall:

đƫ Align the marked centerline on the bracket with the

centerline on the wall.

đƫ Mark 2 screw hole locations in the wall.

đƫ Drill

⁄16” pilot holes in the marked locations.

đƫ Install wall fastener anchors.

đƫ Drive wood screws, by hand, into the fastener to allow

anchors to expand. Remove the screws.

đƫ Secure the bracket to the wall with wood screws and/or

fasteners.

Ceiling

Wall

Vertical Centerline

Ceiling ducting

If the duct will vent straight up to the ceiling:

đƫ Use level to draw a line straight up, from the centerline on

the template to the ceiling.

đƫ Measure at least 4

⁄8 ” from the back wall to the circle cen-

ter of an 6½” hole on the ceiling.

Wall ducting

If ductwork will vent to rear:

NOTE: for minimum duct cover extension we suggest to use a

round to rectangle duct adapter.

đƫ Use a level to draw a line straight up from the centerline

on the template.

đƫ Measure at least 26

⁄2” (the measure might vary depending

on the elbow used) above the pencil line that indicates

the bottom installation height, to the circle center of an

6½” diameter duct hole (hole may be elongated for duct

elbow).

House wiring location

đƫ The junction box is located on the top left side of the

hood.

đƫ Wiring should enter the back wall at least 20

⁄4” above

the bottom of the installation height, and within 7

⁄8” and

⁄8”of the left side of the centerline.

FOR CEILING

VENT DUCTING

FOR

WALL

VENT

DUCT

Ceiling

⁄2”

dia. hole

Circle center at 26

⁄2”

above the marked

bottom line.

⁄8” circle

center to wall

Horizontal straight

pencil line

Install framing for hood support

đƫ If drywall is present, mark the screw hole locations.

Remove the template.

đƫ Cut away enough drywall to expose 2 vertical studs at the

holes location indicated by the template. Install two hori-

zontal supports at least 4” x 2” between two wall studs at

the bottom and upper mounting holes installation location.

đƫ The horizontal support must be ﬂush with the room side of

the studs. Use cleats behind both sides of the support to

secure to wall studs.

đƫ Reinstall drywall and reﬁnish.

IMPORTANT:

Framing must be capable of supporting 100 lbs.

⁄2” min. opening for ductwork

View from

rear cleats

1”x6” min.

mounting

support

Centerline of

installation

space

Mounting the hood

Install the 6” round transition as shows the image below.

The installation screws and the 6” round transition are included

on the hood package.

Ø 6”

I WARNING

2 PEOPLE ARE REQUIRED TO LIFT AND POSITION THE

HOOD ONTO THE MOUNTING SCREWS.

đƫ Place the template on the wall along the horizontal line,

make sure the template is leveled and centered with the

centerline.

đƫ Mark “upper” screw holes locations in the wall.

IMPORTANT. Check to be sure that hole locations are leve-

led and correctly centered by the vertical centerline.

đƫ Drive “upper” wood screws by hand. Leave ¼ “ of distance

between the screw head and the wall.

đƫ Remove the grease ﬁlter and mount the hood onto the

“upper” screws.

đƫ Mark “lower” wood screw holes

locations in the wall using a

pencil.

đƫ Remove the hood.

đƫ Drive “lower” wood screws, by

hand. Remove screws.

đƫ Mount the hood onto the “upper”

screws.

đƫ Drive and tighten the “upper” wood

screws, by hand.

đƫ Drive and tighten the “lower” wood

screws, by hand.

Connecting the ductwork

đƫ Install ductwork, making connections in the direction of

airow as illustrated.

đƫ Push duct over the exhaust outlet.

đƫ Wrap all duct joints and the ﬂange connections with duct

tape for an airtight seal.

đƫ Make the same connection in the wall or ceiling vent exit.

Airflow

Duct tape

over seam

Electrical Connection

I WARNING

ELECTRICAL SHOCK HAZARD.

I WARNING

TURN OFF POWER CIRCUIT AT THE SERVICE PANEL

BEFORE WIRING THIS UNIT.

120 VAC, 15 OR 20 AMP CIRCUIT REQUIRED.

ELECTRICAL GROUNDING INSTRUCTIONS

This appliance is ﬁtted with an electrical junction box with

3 wires, one of which (green/yellow) serves to ground the

appliance.

To protect you against electric shock, the green and yellow

wire must be connected to the grounding wire in your home

electrical system, and it must under no circumstances be cut

or removed.

Failure to do so can result in death or electrical shock.

Facing the front of the range hood, remove the left knockout

and the Junction box cover and install the conduit connector

(cULus listed) in junction box.

Knockout

Junction

box cover

đƫ If not already done, install

⁄2” conduit connector in j-box.

đƫ Use UL listed wire connectors and connect black wires

together.

đƫ Use UL listed wire connectors and connect white wires

together.

đƫ Connect green (or bare) ground wire from home power

supply to yellow-green ground wire in terminal box using

UL listed wire connectors.

đƫ Install terminal box cover.

Metal

electrical

conduit

House

wiring

UL listed

wire nut

Mounting the duct cover

Note: Upper Duct Cover may be placed upside down to hide

(or unhide) louver holes.

đƫ Position the duct cover over the mounted hood.

đƫ Slide the bottom of the duct into the canopy area.

đƫ Position the top of the duct over the duct mounting

bracket. If a telescopic duct cover is used, grab the upper

part of the telescopic duct cover, pull it and place it in the

duct cover mounting bracket.

đƫ Secure the top of the duct with 2 assembly screws

provided.

đƫ Secure the bottom of the duct with 2 assembly screws

provided.

đƫ Install the grease ﬁlter and turn power on at service panel.

Check operation of the hood.

If range hood does not operate:

đƫ Check that the circuit breaker is not tripped or the house

fuse blown.

đƫ Disconnect power supply. Check that wiring is correct.

To get the most ecient use from your new range hood, read

the “Description of the Hood” and “Control” sections.

Keep your Installation Instructions and Use and Care Guide

close to range hood for easy reference.

Installation- Ductless (Recirculating) version

I CAUTION

To install the hood in this version, ﬁrst purchase the

Ductless Recirculating Kit.

includes:

charcoal ﬁlter and deﬂector

đƫ If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall. Otherwise put a thick, protective covering over

countertop, cooktop or range to protect from damage and

debris. Select a ﬂat surface for assembling the unit.

Cover that surface with a protective covering and place all

canopy hood parts and hardware in it.

đƫ Determine and mark the centerline on the wall where the

canopy hood will be installed.

đƫ Select a mounting height comfortable for the user and

mark on wall.

đƫ Tape template, matching center-line and hood bottom.

Mounting the duct cover bracket

The duct bracket should be installed against the back wall

and flush with the ceiling.

This bracket will hold the telescopic duct cover in place at

the top.

Secure the bracket to the wall:

đƫ Align the marked centerline on the bracket with the

centerline on the wall.

đƫ Mark 2 screw hole locations in the wall.

đƫ Drill

⁄16” pilot holes in the marked locations.

đƫ Install wall fastener anchors.

đƫ Drive wood screws, by hand, into the fastener to allow

anchors to expand. Remove the screws.

đƫ Secure the bracket to the wall with wood screws and/or

fasteners.

Ceiling

Wall

Vertical Centerline

House wiring location

đƫ The junction box is located on the top left side of the

hood.

đƫ Wiring should enter the back wall at least 20

⁄4” above

the bottom of the installation height, and within 7

⁄8” and

⁄8”of the left side of the centerline.

Install framing for hood support

đƫ If drywall is present, mark the screw hole locations.

Remove the template.

đƫ Cut away enough drywall to expose 2 vertical studs at the

holes location indicated by the template.

Install two horizontal supports at least 4” x 2” between

two wall studs at the bottom and upper mounting holes

installation location.

đƫ The horizontal support must be ﬂush with the room side of

the studs. Use cleats behind both sides of the support to

secure to wall studs.

đƫ Reinstall drywall and reﬁnish.

IMPORTANT: Framing must be capable of supporting 100 lbs.

⁄2” min. opening for ductwork

View from

rear cleats

1”x6” min.

mounting

support

Centerline of

installation

space

Mounting the hood

Install the 6” round transition as shows the image below.

The installation screws and the 6” round transition are included

on the hood package.

Ø 6”

I WARNING

2 PEOPLE ARE REQUIRED TO LIFT AND POSITION THE

HOOD ONTO THE MOUNTING SCREWS.

đƫ Place the template on the wall along the horizontal line,

make sure the template is leveled and centered with the

centerline.

đƫ Mark “upper” screw holes locations in the wall.

đƫ IMPORTANT. Check to be sure that hole locations are leve-

led and correctly centered by the vertical centerline.

đƫ Drive “upper” wood screws by hand. Leave ¼ “ of distance

between the screw head and the wall.

đƫ Remove the grease ﬁlter and mount the hood onto the

“upper” screws.

đƫ Mark “lower” wood screw holes

locations in the wall using a

pencil.

đƫ Remove the hood.

đƫ Drive “lower” wood screws, by

hand. Remove screws.

đƫ Mount the hood onto the “upper”

screws.

đƫ Drive and tighten the “upper”

wood screws, by hand.

đƫ Drive and tighten the “lower”

wood screws, by hand.

Air deﬂector installation

đƫ Assemble the air deﬂector with the duct cover bracket

with 4 assembly screws provided as shown.

đƫ Measure from the bottom of the air deﬂector to the

bottom of the hood outlet, as shown.

Dimension to measure

đƫ Cut the duct at the measured size.

đƫ Uninstall the air deﬂector removing the 4 assembly screws.

đƫ Slip the duct onto the bottom of the deﬂector.

đƫ Place the assembled deﬂector and duct over the exhaust

outlet from the hood.

Electrical Connection

I WARNING

ELECTRICAL SHOCK HAZARD.

I WARNING

TURN OFF POWER CIRCUIT AT THE SERVICE PANEL

BEFORE WIRING THIS UNIT.

120 VAC, 15 OR 20 AMP CIRCUIT REQUIRED.

ELECTRICAL GROUNDING INSTRUCTIONS

This appliance is ﬁtted with an electrical junction box with 3

wires, one of which (green/yellow) serves to ground the ap-

pliance.

To protect you against electric shock, the green and yellow

wire must be connected to the grounding wire in your home

electrical system, and it must under no circumstances be cut

or removed.

Failure to do so can result in death or electrical shock.

Facing the front of the range hood, remove the left

knockout and the Junction box cover and install the

conduit connector (cULus listed) in junction box.

Knockout

Junction

box cover

đƫ If not already done, install a

⁄2” conduit connector in j-box.

Use UL listed wire connectors and connect black wires

together.

đƫ Use UL listed wire connectors and connect white wires

together.

đƫ Connect green (or bare) ground wire from home power

supply to yellow-green ground wire in terminal box using

UL listed wire connectors.

đƫ Install terminal box cover.

Metal

electrical

conduit

House

wiring

UL listed

wire nut

Mounting the duct cover

Note: Upper Duct Cover may be placed upside down to hide

(or unhide) louver holes.

đƫ Position the duct cover over the mounted hood.

đƫ Slide the bottom of the duct into the canopy area.

đƫ Position the top of the duct over the duct mounting

bracket. If a telescopic duct cover is used, grab the upper

part of the telescopic duct cover, pull it and place it in the

duct cover mounting bracket.

đƫ Secure the top of the duct with 2 assembly screws

provided.

đƫ Secure the bottom of the duct with 2 assembly screws

provided.

đƫ Install the charcoal ﬁlter on the back side of the grease

ﬁlter, install both on the range hood and turn power on at

service panel. Check operation of the hood.

If range hood does not operate:

đƫ Check that the circuit breaker is not tripped or the house

fuse blown.

đƫ Disconnect power supply. Check that wiring is correct.

To get the most ecient use from your new range hood, read

“Description of the Hood” and “Control” sections.

Keep your Installation Instructions and Use and Care Guide

close to range hood for easy reference.

Description of the hood

1. Blower and light controls

2. Halogen lamps

3. Grease filter Handle

4. Grease filter

5. Canopy

6. Duct covers

7. Recirculating grid (only for

recirculating version)

Control

CFM

REDUCTION

SYSTEM

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Note: Hood retains last speed setting when aspiration

switch is turned o.

Description of control panel

CHARCOAL FILTER GREASE FILTER

1. Light Button

đƫ Press lamp button to turn ON the light on High Intensity

(Lamp state previously OFF).

đƫ Press lamp button to turn ON the light on Low Intensity

(Lamp state previously ON).

đƫ Press lamp button to turn OFF the light (Lamp state

previously ON).

2. Timer Button

đƫ The default timer setting is 10 minutes, and it can be

adjusted between 60 minutes and 1 minute.

đƫ After pressing the timer button, the control enters to a

timer setup mode, and user can adjust the timer

countdown time with the “+” and “-” buttons within 5

seconds. The timer can be initiated immediately pressing

the timer button, after setting the timer duration or

pressing the timer button twice (default 10 minutes

setting).

đƫ If no action occurs within 5 seconds, the countdown

will start.

đƫ During the timer setup the “+” and “-” buttons are

dedicated to the timer and no motor action will occur.

đƫ Once the timer is initiated, it can be cancelled by

pressing the timer button again.

3. Display

đƫ Shows the hood settings.

đƫ The display will be lit at low intensity when the hood

is not operating.

đƫ Pressing any key the display will light up at high intensity.

đƫ The display will be lit at high intensity when the hood

is operating.

đƫ If no key is pressed within a minute the display will return

to being lit at low intensity.

4. “-” Button. Speed Decrease / OFF

đƫ This button is used to decrease the fan speed, or turn

OFF the fan.

đƫ The fan will turn OFF if the “-” button is pressed and

the hood was in the ﬁrst speed.

đƫ If the fan is at second speed and the “-” button is

pressed, the fan will be set to ﬁrst speed.

đƫ

If the fan is at third speed and the “-” key is pressed,

the fan will be set to second speed.

đƫ If the fan is at fourth speed and the “-” button is

pressed, the fan will be set to third speed.

đƫ If the fan is OFF and the “-” button is pressed, the

control backlight will light up.

5. “+” Button. Speed Increase / ON

đƫ This button is used to increase the fan speed, or turn

ON the fan.

đƫ The fan will turn ON if the “+” button is pressed and the

hood was OFF.

đƫ If the fan is at ﬁrst speed and the “+” button is pressed,

the fan will be set to second speed.

đƫ If the fan is at second speed and the “+” button is pressed,

the fan will be set to third speed.

đƫ If the fan is at third speed and the “+” button is pressed,

the fan will be set to fourth speed.

đƫ If the fan is at fourth speed and the “+” button is pressed,

a beep will sound.

Clock programming

đƫ The clock can be reprogrammed at any time except

during an active timed function.

đƫ The clock can be displayed in a twelve hour format and

valid clock times are from 1:00 to 12:59.

đƫ The clock can be reprogrammed pressing the “Timer”

button for 3 seconds, and after, the clock can be

adjusted with the “+” and “-” buttons.

đƫ The user can have minute increments / decrements of

1 minute, but if the user keep pressing the “+” / ”-”

buttons for more than 1 second, the increments /

decrements will be of 5 minutes.

đƫ During this option the control will round to the nearest

5 minutes.

đƫ The user can ﬁnish on reprogramming the clock

pressing the “Timer” button.

đƫ After 1 minute of no button pressed the control will

accept the programmed clock time and will add one

minute to the set clock.

Grease ﬁlter saturation alarm

đƫ After thirty fan functional hours, the display will show

“Grease Filter” if the fan is active.

When this icon is shown in the display, the grease

ﬁlters installed are required to be washed.

đƫ To reset the grease ﬁlter saturation alarm the user must

press the “+” button for 5 seconds, after this action the

icon “Grease ﬁlter” is not displayed, and the hood has the

normal display operation.

Charcoal ﬁlter saturation alarm

đƫ After one hundred and twenty functional hours of the

fan, the display will show “Charcoal Filter” if the fan is

active. When this icon ﬂashes on display, the charcoal

ﬁlters installed are required to be replaced or

reactivated.

đƫ To reset the charcoal ﬁlter saturation indication the

user must press the “-” button for 5 seconds, after this

time the icon “Charcoal ﬁlter” is not displayed and the

hood has the normal display operation.

Audible feature activation and deactivation

đƫ The audible features can be activated or deactivated

pressing the “Light” button for 5 seconds.

đƫ If the audible feature is activated, a tone must sound

and the “Snd” symbol must appear on the display for

3 seconds.

đƫ If the audible feature is deactivated, the “Snd” symbol

must appear on the display for 3 seconds and no tone

must sound.

Charcoal ﬁlter inclusion and exclusion (Recirculating

accessories)

đƫ The charcoal ﬁlter inclusion or exclusion can be set by

pressing the “+” and “-” buttons at the same time for 5

seconds.

đƫ The Inclusion or exclusion of charcoal ﬁlter must be

selected while the lamps and the motor are OFF.

đƫ When the charcoal ﬁlter has been excluded, the

charcoal ﬁlter alarm is disabled.

Heat sensor

đƫ The control is equipped with a heat sensor that will

turn on the blower at third speed if excessive heat

occurs (over 149° F or 65°C) surrounding the control

area.

đƫ If the blower is OFF or if it is operating at ﬁrst speed,

the blower will be set automatically to third speed, the

display shows the word “CArE” to indicate that heat

sensor has detected an excessive heat.

đƫ During this state, the user may raise the blower speed

to fourth speed but can not decrease the speed.

đƫ When the temperature level on the hood drops to

normal, the blower will operate in the setting deﬁned

by the user before the alarm occured.

BEFORE OPERATING YOUR HOOD

Some regions and provinces of the US and Canada restrict

the exhausting power of range hoods to performances below

certain values. These values are underlined in the local code

for your area.

Please check your local code to ﬁnd out if you will need to

restrict the power of your hood.

If your local code restricts the performance values of range

hoods, please execute the following button-pressing se-

quence:

Low performance

đƫ Press the TIMER (1), LIGHTS (2) and - (3) buttons together

for 5 seconds

đƫ Result:

The “LO” indicator will be displayed.

The 3rd and 4th speeds will be Disabled.

Mainteinance

I ATTENTION!

Before performing any maintenance operation, isolate the

hood from the electrical supply by switching o at the con-

nector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

Do not spray cleaners directly to the control while cleaning

the Hood.The cooker hood should be cleaned regularly (at

least with the same frequency with which you carry out main-

tenance of the fat ﬁlters) internally and externally. Clean using

the cloth dampened with neutral liquid detergent. Do not use

abrasive products. DO NOT USE ALCOHOL!

I WARNING

Failure to carry out the basic cleaning recommendations of

the cooker hood and replacement of the ﬁlters may cause ﬁre

risks. Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any ﬁre damage linked to inappropriate maintenan-

ce or failure to observe the above safety recommendations.

Grease Filter

Traps cooking grease particles. This must be cleaned once a

month using non aggressive detergents, either by hand or in

the dishwasher, which must be set to a low temperature and

a short cycle. When washed in a dishwasher, the grease ﬁlter

may discolour slightly, but this does not aect its ﬁltering

capacity. To remove the grease ﬁlter, pull the spring release

handle.

A. Spring release handle

Replacing lamps

CAUTION

Before replacing the lamps, switch power o at service panel

and lock service panel disconnecting means to prevent power

from being switched on accidentally.

NOTE: Turn o the lights and fan. Allow the lights to cool

before handling. If new lights do not operate be sure lights are

inserted correctly before calling service.

Replace Lights

đƫ Remove the inner lamp lens cover by inserting a small

ﬂat blade screwdriver into each of the three slots and

gently prying it free.

NOTE: Do not remove the outer trim ring (lamp assembly).

Grasp the bulb and pull it straight out.

đƫ Replace with 120 volt, 40 watt halogen bulbs with a G9

base SUITABLE FOR USE IN OPEN LUMINAIRES.

đƫ Follow package directions, wear gloves, do not touch bulb

with your bare ﬁngers.

đƫ Replace inner cover by inserting the three retaining tabs

into the three slots and pressing them ﬁrmly in place.

Light

bulb

Charcoal Filter

If the model is not vented to the outside, the air will be recir-

culated through disposable charcoal ﬁlters that help remove

smoke and odors.

The charcoal ﬁlters are clipped on the motor housing frame.

NOTE: Charcoal ﬁlters are not included with the hood. They

must be ordered from your supplier.

Order the needed kit specifying your hood model and width size.

Charcoal

ﬁlter handle

Charcoal

ﬁlter

Motor

housing

frame

Cleaning/replacing the charcoal ﬁlter

Unlike other charcoal ﬁlters, the LONGLIFE charcoal ﬁlter can

be cleaned and reactivated.

With normal use the ﬁlter should be cleaned every second

month (when using the hood 2.5 hours per day,on average).

The best way to clean the ﬁlter is in the dishwasher.

Use normal detergent and choose the highest temperature

(65º C or 149° F).

Wash the ﬁlter separately so that no food parts gets stuck on

the ﬁlter and later causes bad odours.

To reactivate the charcoal, the ﬁlter should be dried in an oven

for 10 minutes with a maximum temperature of

100º C or

212° F.

After approximately one year of use, the charcoal ﬁlter should

be replaced with a new one, as the odour reduction capacity

will be reduced.

ELICA North America

TWO-YEARS LIMITED WARRANTY

TO OBTAIN SERVICE UNDER WARRANTY

Owner must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in

order to obtain service under warranty.

PARTS AND SERVICE WARRANTY

For the period of two (2) years from the date of the original purchase, Elica will provide free of charge, non consumable

parts or components that failed due to manufacturing defects. During these two (2) years limited warranty, Elica will

also provide free of charge, all labor and in-home service to replace any defective parts.

WHAT IS NOT COVERED

đƫ Damage or failure to the product caused by accident or act of God, such as, ﬂood, ﬁre or earthquake.

đƫ Damage or failure caused by modiﬁcation of the product or use of non-genuine parts.

đƫ Damage or failure to the product caused during delivery, handling or installation.

đƫ Damage or failure to the product caused by operator abuse.

đƫ Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.

đƫ Damage or failure caused by use of product in a commercial application.

đƫ Service trips to dwelling to provide use or installation guidance.

đƫ Light bulbs, metal or carbon ﬁlters and any other consumable part.

đƫ Normal wear of ﬁnish.

đƫ Wear to ﬁnish due to operator abuse, improper maintenance, use of corrosive or abrasive cleaning products/pads and

oven cleaner products.

WHO IS COVERED

This warranty is extended to the original purchaser for products purchased for ordinary residential use in North America

(Including the United States, Guam, Puerto Rico, US Virgin Islands & Canada).

This warranty is non-transferable and applies only to the original purchaser and does not extend to subsequent owners of

the product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including, but not limited

to any implied warranty of merchantability or ﬁtness for a particular purpose and all other obligations on the part of Elica

North America, provided, however, that if the disclaimer of implied warranties is ineective under applicable law, the dura-

tion of any implied warranty arising by operation of law shall be limited to two (2) years from the date of original purchase

at retail or such longer period as may be required by applicable law.

This warranty does not cover any special, incidental and/or consequential damages, nor loss of proﬁts, suered by the

original purchaser, its customers and/or the users of the Products.

WHO TO CONTACT

To obtain service under warranty or for any service related question, please visit the support section on the website below:

www.elica.com

Have your product proof of purchase with date ready for warranty issues.

FRANÇAIS

Sommaire

Avis de sécurité important........................................................................................................................................................................................... 17

Exigences électriques et exigences d’installation.......................................................................................................................................... 18

Avant d’installer la hotte.......................................................................................................................................................................................... 18

Dimensions et Dégagement......................................................................................................................................................................................... 18

Liste des pièces.................................................................................................................................................................................................................19

Pièces fournies............................................................................................................................................................................................................. 19

Pièces non fournies.................................................................................................................................................................................................... 19

Exemples et possibilités de positionnement des conduits.............................................................................................................................. 20

Installation (Version à conduit) ................................................................................................................................................................................. 20

Installation (Version sans conduit [recyclage]) ................................................................................................................................................... 23

Description de la hotte.................................................................................................................................................................................................. 26

Commandes....................................................................................................................................................................................................................... 26

Entretien.............................................................................................................................................................................................................................. 28

Garantie................................................................................................................................................................................................................................ 29

APPROUVÉ POUR LES APPAREILS DE TYPE RÉSIDENTIEL

POUR UNE UTILISATION RÉSIDENTIELLE SEULEMENT

LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES

VEUILLEZ LIRE CES INSTRUCTIONS AU COMPLET AVANT DE COMMENCER.

L’INSTALLATION DE L’APPAREIL DOIT RESPECTER TOUS LES CODES EN VIGUEUR.

IMPORTANT : Conservez ces instructions aﬁn de pouvoir les remettre à l’inspecteur-électricien de votre région.

INSTALLATEUR : Veuillez laisser ces instructions avec l’appareil pour le propriétaire.

PROPRIÉTAIRE : Veuillez conserver ces instructions pour pouvoir vous y référer plus tard.

Avertissement de sécurité : Coupez l’alimentation du circuit dans le panneau électrique et verrouillez le

panneau avant de raccorder les ﬁls de cet appareil.

Exigence : 120 V c.a., 60 Hz circuit de dérivation de 15 V c.a., 20 Hz, de 15 ou 20 A.

AVIS DE SÉCURITÉ IMPORTANT

I ATTENTION

UTILISER CET APPAREIL À DES FINS DE VENTILATION

GÉNÉRALE SEULEMENT. NE PAS UTILISER CET APPAREIL

POUR ÉVACUER DES MATÉRIAUX OU DES VAPEURS DAN-

GEREUX OU EXPLOSIFS.

I AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLEC-

TRIQUE ET DE BLESSURE, RESPECTER LES DIRECTIVES

SUIVANTES :

A. Utiliser cet appareil uniquement aux ﬁns prévues par le

fabricant. Si vous avez des questions à propos de

l’appareil, communiquez avec le fabricant.

B. Avant de faire l’entretien de l’appareil ou de le nettoyer,

coupez l’alimentation dans le panneau électrique et

verrouillez le panneau en bloquant le dispositif

permettant d’empêcher d’activer l’alimentation

accidentellement. S’il n’est pas possible de verrouiller

l’accès au panneau, ﬁxez une étiquette très voyante au

panneau électrique.

C. Une personne qualiﬁée doit eectuer l’installation et le

câblage des ﬁls électriques en conformité avec tous les

codes et toutes les normes, y compris la cote de

résistance au feu.

D. Il est important de prévoir susamment d’air pour

assurer une bonne combustion de l’équipement de

chaue et l’évacuation adéquates des gaz par le conduit

de cheminé aﬁn de prévenir les refoulements d’air.

Respectez les directives et les normes de sécurité des

fabricants de l’équipement de chauage, comme celles

publiées par la National Fire Protection Association

(NFPA), la American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) et le code

des autorités de votre région.

E. Au moment de couper ou de percer un mur ou un

plafond, assurez-vous de ne pas endommager la ﬁlerie

électrique ou tout autre accès à un service publique.

F. Il faut toujours évacuer à l’extérieur les systèmes conduit.

I ATTENTION

Pour réduire les risques d’incendie et évacuer l’air correcte-

ment, assurez-vous que le conduit mène à l’extérieur; il ne

faut pas évacuer l’air dans l’espace entre les murs, dans les

plafonds, dans les greniers, les vides sanitaires ou les garages.

I AVERTISSEMENT

POUR RÉDUIRE DES RISQUES D’INCENDIE, UTILISEZ

UNIQUEMENT DES CONDUITS EN MÉTAL.

Installez cette hotte en respectant toutes les exigences

mentionnées.

I AVERTISSEMENT

Pour réduire les risques d’incendie et de choc électrique,

n’utilisez pas cette hotte avec un contrôleur de vitesse à semi-

conducteurs.

I AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE DE GRAISSE SUR

LES CUISINIÈRES.

a) Ne laissez jamais la cuisinière sans surveillance

lorsqu’elle est réglée à une haute température. Les

débordements par bouillonnement causent de la fumée

et des débordements de gras qui peuvent s’enﬂammer.

Faites chauer l’huile lentement, à une température

basse ou moyenne.

b) Faites toujours fonctionner la hotte lorsque vous

utilisez la cuisinière à une haute température ou que vous

faites ﬂamber des aliments (P. ex. : crêpes Suzette, cerises

jubilées, boeuf au poivre ﬂambé).

c) Nettoyez les hélices de ventilation fréquemment. Il ne faut

pas que la graisse s’accumule sur les ﬁlres ou les hélices.

d) Utilisez le bon format de casserole. Utilisez toujours un

chaudron de taille approprié à l’élément de la cuisinière.

I AVERTISSEMENT

POUR ÉVITER DE BLESSER QUELQU’UN LORS D’UN

INCENDIE DE GRAISSE SUR LA CUISINIÈRE, SUIVRE LES

CONSEILS SUIVANTS:

a) ÉTOUFFER LES FLAMMES avec un couvercle aux

dimensions de la taque de cuisson, une tôle à biscuit ou

tout autre plateau métallique, puis couper le gaz ou

l’alimentation électrique de la cuisinière. FAIRE

ATTENTION A NE PAS SE BRÛLER. Si les ﬂammes ne

s’éteignent pas immédiatement, QUITTER LA PIÈCE ET

APPELER LES POMPIERS.

b) NE JAMAIS PRENDRE EN MAIN UNE CASSEROLE

EN FEU, vous pourriez vous blesser.

c) NE PAS UTILISER D’EAU, y compris les essuies de

vaisselle ou les serviettes humides – une violente

explosion due à la vapeur formée pourrait survenir.

d) Utiliser un extincteur SEULEMENT si:

1) Vous êtes sûr d’avoir un extincteur de classe ABC que

vous savez utiliser.

2) Le feu est petit et conﬁné à la zone où il s’est formé.

3) Les pompiers ont été appelés.

4) Vous pouvez lutter contre le feu avec une sortie

derrière vous.

Recommandations tirées des conseils de sécurité en cas

d’incendie de cuisine publiés par la NFPA.

MODE OPÉRATOIRE

Toujours laisser les grilles de sécurité et les ﬁltres à leurv

place. Sans la présence de ces derniers, les parties aspirantes

pourraient attirer les cheveux, les doigts ou les vêtements.

Le fabricant décline toute responsabilité si les informations

détaillées dans ce manuel pour l’installation, l’entretien et

l’utilisation adéquate du produit ne sont pas observées. Le

fabriquant décline en outre toute responsabilité pour

d’éventuelles blessures dues à des négligences; en outre, la

garantie de l’appareil sera annulée suite à des conditions

d’entretien inappropriées. Cet appareil est fabriqué pour un

usage interne. Ne pas utiliser cet appareil à l’extérieur.

EXIGENCES ÉLECTRIQUES ET D’INSTALLATION

IMPORTANT

Respectez tous les codes et les ordonnances en vigueur.

Le client a la responsabilité de :

đƫ

Contacter un électricien-installateur.

đƫ Vériﬁer que l’installation électrique est adéquate et confor-

me avec le Code national de l’électricité, ANSI/ NFPA

70 (la plus récente édition*), ou les normes C22.1-94, Code

canadien de l’électricité, Partie 1 et C22.2 No.0-M91 (La

plus récente édition**) de la CSA, ainsi que tous les codes

et les ordonnances de votre région.

đƫ Si le code le permet et que vous utilisez un ﬁl de mise

à la terre distinct, il est recommandé de faire vériﬁer le

chemin du ﬁl par un électricien.

đƫ Ne pas mettre l’appareil à la terre sur une conduite de gaz.

đƫ Consultez un électricien qualiﬁé si vous n’êtes pas

certain que la hotte est mise à la terre correctement.

đƫ N’installez pas un fusible dans le circuit neutre ou le

circuit de mise à la terre.

IMPORTANT

đƫ Conservez ces instructions aﬁn de pouvoir les remettre à

l’inspecteur-électricien.

đƫ La hotte doit être câblée uniquement à l’aide de ﬁls de cuivre.

đƫ Il faut raccorder la hotte directement à une boîte à fusible

ou à un disjoncteur par l’entremise d’une canalisation

électrique en métal.

đƫ Le calibre de ﬁl doit être conforme aux exigences du Code

national de l’électricité, ANSI/NFPA 70 (La plus récente

édition*), ou les normes C22.1-94, Code canadien de

l’électricité, Partie 1 et C22.2 0-M91 (La plus récente édition**)

de la CSA, ainsi que tous les codes et les ordonnances de

votre région.

đƫ Il faut prévoir un connecteur de canalisation approuvé

par l’UL ou la CSA à chaque extrémité de la canalisation

d’alimentation (À la hotte et à la boîte de jonction).

Vous pouvez obtenir un exemplaire des normes indiquées en vous adressant à:

* La National Fire Protection Association, Batterymarch Park Quincy, Massachu-

setts, 02269

** La CSA International, 8501 East Pleasant Valley Road, Cleveland, Ohio, 44131-

5575

AVANT D’INSTALLER LA HOTTE

1 Pour assurer la ventilation la plus ecace possible,

installez la conduite en ligne droite ou avec le moins de

coudes possibles.

ATTENTION : La sortie de la conduite de ventilation

doit donner sur l’extérieur.

2 Deux personnes sont nécessaires pour eectuer

l’installation.

3 La quincaillerie fournie permet de ﬁxer la hotte à la

plupart des murs et des plafonds; consultez un

installateur qualiﬁé pour vous assurer que la

quincaillerie fournie est adaptée à votre type de mur

ou d’armoire.

4 N’utilisez pas de conduit ﬂexible.

5 Dans le cas des endroits sujets aux TEMPÉRATURES

FROIDES, il faut installer un clapet de contre-tirage

supplémentaire aﬁn de minimiser le retour d’air froid et

un isolant thermique non métallique aﬁn de minimiser

la conduction de la température extérieur dans le

conduit. Il faut placer le clapet du côté de l’air froid de

l’isolant thermique.

L’isolant doit être placé le plus près possible de

l’endroit où le conduit entre dans la partie chauée de

la maison.

6 Air d’appoint : Le code du bâtiment de votre région

peut exiger l’utilisation d’un système d’air d’appoint si

vous utilisez un système de ventilation à conduit dont

le mouvement d’air dépasse un certain nombre de

CFM. Le nombre de pi3/min varie d’une région à

l’autre. Consultez un professionnel de CVC pour

connaître les exigences précises de votre région.

DIMENSIONS ET DÉGAGEMENT

**D

Modèles

ELG630S2 ELG636S2

A 30” (76 cm) 36” (91.2 cm)

B 19

⁄16” (50 cm)

Max: 42

⁄8” (108.2 cm)

Min: 28

⁄16” (71.9 cm)

D**

Max: 36

⁄16” (93.8 cm)

Min: 24

⁄8” (62.5 cm)

E 6” (15.24 cm)

F 10

⁄4” (27.3 cm)

G 13

⁄16” (33.5 cm)

H 28

⁄8” (73 cm)

I 20

⁄2” (52 cm)

J 5” (12.7 cm)

* Seulement avec la version sans conduit (à recyclage)

** Seulement avec la version version à conduit

LISTE DES PIÈCES

Enlever l’emballage.

I ATTENTION

Enlever délicatement le carton, Porter des gants pour se protéger des bords coupants.

I AVERTISSEMENT

Enlever le ﬁlm de protection recouvrant le produit avant de commencer l’opération.

Pièces Fournies Pièces Pièces Fournies Pièces

Assemblage hotte

Mounting template

5x45 mm

Transition ronde de 6”

4.2x8 mm

Bride de support du

cache-conduit

3.5x9.5 mm

Conduits de cheminée

8x40 mm

Pièces Non Fournies

Outils nécessaires

đƫ Ecrous métalliques

đƫ Ruban pour le gabarit de montage

đƫ Conduit métallique circulaire de 8” pour parfaire

l’installation

đƫ Mètre ruban

đƫ Tenailles

đƫ Gants

đƫ Couteau

đƫ Lunettes de sécurité

đƫ Foreuse électrique 5/16” et 3/8”

đƫ Réducteur de tension

đƫ Niveau

đƫ Toile isolante

đƫ Tournevis:

- Phillips (Pozidrive) # 2

- Torx # 2

đƫ Dénudeur

đƫ Ruban de masquage

đƫ Marteau

đƫ Scie, scie circulaire

Accessoires Optionnel

Trousse de conversion en hotte à recyclage

à utiliser seulement avec la version sans conduit

(À recyclage)

comprend : ﬁltre au charbon, soutien de ﬁltre au charbon et

support de ﬁxation, déﬂecteur.

Exemples et possibilités de positionnement des conduits

Suivez à la lettre les directives présentées dans ce manuel.

Le fabricant refuse toute responsabilité en ce qui a trait à tout préjudice, dommage ou incendie causé par la non observation

des directives contenues dans le présent manuel.

Version à conduit Version sans conduit (Recyclage)

La hotte est dotée d’une transition 6” (15.2 cm) afin

d’évacuer les vapeurs à l’extérieur.

Décharge à travers le toit Décharge à travers le mur

A. Bouche de décharge sur toit

B. Conduit rond de 6”(15,2 cm)

A. Bouche de décharge murale

B. Conduit rond de 6”(15,2 cm)

S’il s’avère impossible

d’évacuer la fumée et

les vapeurs de cuisson à

l’extérieur, il est possible

de transformer la hotte

en version sans conduit

(Recyclage). Fixer un ﬁltre

au charbon et le déﬂceteur

sur le support de couvercle

de conduit. La fumée et la

vapeur sont recyclées.

Dans le cas de la version

sans conduit (À recyclage)

seulement : procurez-vous

la trousse de conversion en

hotte à recyclage.

Diamètre minimum des

conduit: tuyau rond de 6po.

A. Deflécteur

B. Conduit rond de 6”(15,2 cm)

Préparation

Ne coupez pas une solive ou un montant à moins qu’il soit

absolument nécessaire de le faire. Si vous devez couper une

solive ou un montant, vous devez construire un cadre de

soutien.

La quincaillerie fournie permet de fixer la hotte à la plupart

des murs et des plafonds.

Vous devez cependant demander à un technicien qualifié de

vérifier la solidité des matériaux selon le type de mur ou de

plafond.

Avant de couper, assurez-vous qu’il y a un dégagement

suffisant dans le plafond ou le mur pour passer la conduite de

sortie.

Hauteur de montage recommandée:

Vous pouvez déterminer vous-même la hauteur à laquelle

vous installez la hotte au dessus de la cuisinière. Plus la hotte

est près de la cuisinière, plus elle est ecace à capter les

odeurs de cuisson, la graisse et la fumée.

I ATTENTION

POUR L INSTALLATION DES CUISINIERES A GAZ: METTEZ

LA HOTTE AFIN D’AVOIR ENTRE LE BORD INFERIEUR DE

LA HOTTE ET LE PLAN DE CUISSON UNE DISTANCE DE 30”

(76,2 CM).

POUR DES CUISINIERES ELECTRIQUES: LA DISTANCE

ENTRE LE BORD INFERIEUR DE LA HOTTE ET LE PLAN DE

CUISSON NE DÔIT PAS ÊTRE INFERIEURE DE 24” (61 CM) ET

SUPERIEURE DE 30” (76,2 CM).

EMPLOI DOMESTIQUE. LIRE ATTENTIVEMENT LE LIVRET

INSTRUCTIONS POUR DES APPLICATIONS SPECIFIQUES.

Vériﬁez donc la hauteur de votre plafond et la hauteur maxi-

mum de la hotte avant de choisir votre modèle de hotte.

Installation - Version à conduit

đƫ Si possible, débranchez la cuisinière et déplacez-la aﬁn

d’avoir un meilleur accès au mur arrière. Sinon, placez une

couverture épaisse sur le comptoir et la surface de cuisson

aﬁn de les protéger des dommages et des saletés. Sélec-

tionnez une surface plane pour assembler l’appareil. Placez

une couverture protectrice sur cette surface, puis disposez

les pièces de l’auvent de la hotte et la quincaillerie.

đƫ Déterminez et marquez la ligne centrale sur le mur où sera

installé l’auvent de la hotte.

đƫ Déterminez une hauteur confortable pour l’utilisateur et

marquez-la sur le mur derrière la surface de cuisson.

đƫ Posez le modèle sur la ligne centrale et le bas de la hotte à

l’aide de ruban adhésif.

Placer les équerres du conduit de cheminée

Le conduit de cheminée doit être installé contre le mur de

fond et au niveau du plafond.

Cette équerre va maintenir le conduit de cheminée en place

au sommet.

Attacher les équerres au mur:

đƫ Aligner les lignes médianes tracées sur les équerres avec

les lignes médianes sur le mur.

đƫ Indiquer les 2 trous pour les vis sur le mur.

đƫ Forer des trous pilotes de

⁄16” sur les emplacements

indiqués.

đƫ Placer les attaches d’accrochage au mur.

đƫ Visser les vis à bois, à la main, dans les attaches pour

permettre aux crochets de se dilater. Enlever les vis.

đƫ Attacher l’équerre dans le mur à l’aide des vis à bois et/ou

des attaches.

La page charge ...

ELICA ELG630S2 Guide d'installation

Marque: ELICA

Modèle: ELG630S2

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: ELICA ELG630S2 Installation guide
español: ELICA ELG630S2 Guía de instalación

ELICA ELG630S2 Guide d'installation

ELICA ELG630S2 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents