Mellanox Technologies SwitchX MSX1016X-2BFR Hardware User Manual

www.mellanox.com

SwitchX® 64 Port SFP+ Ethernet Switch

Hardware User Manual

P/N: MSX1016X-2BFR, MSX1016X-2BRR

Rev 1.2

Document Number: 3727

Rev 1.2

Mellanox Technologies

2

Mellanox Technologies

350 Oakmead Parkway Suite 100

Sunnyvale, CA 94085

U.S.A.

www.mellanox.com

Tel: (408) 970-3400

Fax: (408) 970-3403

Mellanox Technologies, Ltd.

Beit Mellanox

PO Box 586 Yokneam 20692

Israel

www.mellanox.com

Tel: +972 (0)74 723 7200

Fax: +972 (0)4 959 3245

Mellanox®, Mellanox logo, BridgeX®, ConnectX®, CORE-Direct®, InfiniBridge®, InfiniHost®, InfiniScale®, PhyX®,

SwitchX®, Virtual Protocol Interconnect® and Voltaire® are registered trademarks of Mellanox Technologies, Ltd.

Connect-IB™, FabricIT™, MLNX-OS™, ScalableHPC™, Unbreakable-Link™, UFM™ and Unified Fabric Manager™ are

trademarks of Mellanox Technologies, Ltd. All other trademarks are property of their respective owners.

NOTE:

THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED

DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY

KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE

THE PRODUCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT

HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE

PRODUCTO(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT AND

DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST

QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT

ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES

FOR ANY DIRECT, INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND

(INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND RELATED

DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

3

Contents

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

About this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Mellanox Part Numbering Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

1.2 Serial Number and Product Version Information . . . . . . . . . . . . . . . . . . .11

Chapter 2 Installation Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3 Hardware Basic Operation and Installation. . . . . . . . . . . . . . . . . . . 15

3.1 Switch Platform Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3.1.1 LED Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1.2 Port Connector LED Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.2 Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

3.3 SFP+ Cable Power Budget Classification . . . . . . . . . . . . . . . . . . . . . . . .18

3.4 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

3.4.1 Port Connector Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.5 Management and Firmware Updating Interfaces . . . . . . . . . . . . . . . . . . .19

3.5.1 RJ-45 Console Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.5.2 Mini USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.5.3 RJ-45 Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.5.4 I2C Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Chapter 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1 Package Contents and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4.1.1 Installing the Switch in the Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1.2 Power Connections and Initial Power On. . . . . . . . . . . . . . . . . . . . . . . . . 26

4.1.3 Grounding the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.1.4 Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.1.5 Cable Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.1.6 Supported Approved Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.2 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Chapter 5 Management and Tools Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.1 Chassis Management Using the MLNX-OS Software . . . . . . . . . . . . . . .29

5.2 Configuring the Switch for the First Time . . . . . . . . . . . . . . . . . . . . . . . .29

5.2.1 Starting a Remote Connection to the Switch . . . . . . . . . . . . . . . . . . . . . . 29

5.2.2 Upgrading Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Rev 1.2

Mellanox Technologies

4

Chapter 6 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Appendix A Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

A.1 Approved Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

A.2 EMC Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

A.3 China CCC Warning Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Appendix B Thermal Threshold Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Appendix C Transferring the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Appendix D SFP+ Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Appendix E Replacement Parts Ordering Numbers . . . . . . . . . . . . . . . . . . . . . 43

Appendix F Avertissements de sécurité d’installation (French) . . . . . . . . . . . 44

Appendix G Installation - Sicherheitshinweise (German) . . . . . . . . . . . . . . . . 47

Appendix H Advertencias de seguridad para la instalación (Spanish). . . . . . 51

Appendix I Special Regulations Regarding Finland, Sweden, Denmark, and Norway 54

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

5

List of Figures

Figure 1: SX1016 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Figure 2: Generic Product label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Figure 3: Management MAC Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Figure 4: Switch System Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Figure 5: Status LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Figure 6: LED to Port Assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Figure 7: Port Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Figure 8: Management Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Figure 9: Rack Rail Kit Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Figure 10: Placement of Switch in Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Figure 11: Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Figure 12: Screwing on the Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Figure 13: Inserting the Caged Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Figure 14: Slide the Rail into the Rail Slide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Figure 15: Cable Orientation for Insertion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Figure 16: Host Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Figure 17: Transfer Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Figure 18: Put the Cord Through the Switch Slide Before Screwing it to the Switch . . . . . .38

Figure 19: Screw the Switch Slide to the Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Figure 20: Transfer Power Cord Finished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Rev 1.2

Mellanox Technologies

6

List of Tables

Table 1: Revision History Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 2: Reference Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 3: Switch Status LED Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 4: Fan LED Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 5: Bad Port LED Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 6: Port Connector Physical and Logical Link Indications . . . . . . . . . . . . . . . . . . . 18

Table 7: Installation Kit According to Rack Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 8: SX1016 Specification Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 9: SFP+ Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 10: Replacement Parts Ordering Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

7

Revision History

Table 1 - Revision History Table

Date Revision Description

November 2012 Rev 1.2 Removed Updating FW section; not needed for Ethernet switches

October 2012 Rev 1.1 • Added China CCC Warning Statement

• Fixes to port to LED assignment

February 2012 Rev 1.0 Initial release

Rev 1.2

Mellanox Technologies

8

About this Manual

This manual describes the installation and basic use of the Mellanox SX1016 switch, which is

based on the SwitchX® switch device.

Intended Audience

This manual is intended for users and system administrators responsible for installing and setting

up the switch platforms listed above.

The manual assumes familiarity with Ethernet Networks and Architecture.

Related Documentation

Additional Documentation available from Mellanox:

Conventions

Throughout this manual, the name SX1016 and the term switch are used to describe the 64-port

SFP+ 10Gb/s switch unless explicitly indicated otherwise.

The following icons are used throughout this document to indicate information that is important

to the user.

Table 2 - Reference Documents

Switch Firmware and

Firmware Update

Tools

See 

http://www.mellanox.com > Support > Download Firmware Tools

This symbol signals recommendations to the user.

This symbol indicates information that is helpful to the user.

This symbol indicates a situation that can potentially cause damage to hardware or

software.

BEWARE! This symbol indicates a situation that can potentially cause personal injury

or damage to hardware or software.

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

9

Mellanox Part Numbering Legend

Place Field Decoder

M Mellanox Technologies

SX System Type SwitchX® silicon

B Protocol (1, 2, 3, 4) = Ethernet

C Height of Unit 0 = 1U

1 = 1.5U

2 = 2U

FF # of 40Gb/s Ports equivalent 16

G Line rate of the fastest port X = 10GbE

- Separator

# Power supplies

number of power supplies

shipped with the basic sys-

tem

2 = 2 power supplies

M Depth of the Unit B = short depth

Y Air Flow direction R= Connector side to PSU side airflow 

F= PSU side to connector side airflow

R Chip Generation R – SwitchX

S – SwitchX-2

Overview

Rev 1.2

Mellanox Technologies

10

1 Overview

The SX1016 is an economical, high-performance 64-port 10GbE switch providing 1.28Tb/s of

line rate performance. Based on Mellanox’s SwitchX® silicon and innovative hardware design,

the switch packs 64 SFP+ interfaces in an ultra-dense 1U form factor. The SX1016 features

industry leading latency of 250ns and power of less than 1.0W per port, providing optimal per-

formance and efficiency for enterprise data center, financial services, Web 2.0, High Performance

Computing and cloud computing applications.

Basic installation and hardware maintenance is covered in “Hardware Basic Operation and

Installation” on page 15.

Figure 1: SX1016 Switch

1.1 Features

The SX1016 supports the following features:

• 64 SFP+ ports of 10 Gb/s

• up to 24 native Fiber Channel ports

• Two management options:

• Supports Mellanox PPC460 Mezzanine CPU

• Supports Mellanox X86 Mezzanine CPU

• 2 250W AC/DC fixed Power supplies

• 6 Fixed Fans with 5+1 redundancy

• On board temperature monitoring

• Reset Push button on front panel

• Front Panel indication LEDs:

• Status LED (Red / Yellow / Green)

• Fans Status LED (Red / Green)

• UID LED (Blue)

• Bad port LED (Yellow / Green)

RST

UID

S

X

1

0

1

6

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

11

1.2 Serial Number and Product Version Information

The serial number and MAC for the switch are found on the back panel. The serial number and

product version information are found on the label seen in the figure below. Near this label is

another label with the management MAC.

Figure 2: Generic Product label

Figure 3: Management MAC Label

P/N:MSX1016X‐2BFR

Rev:X1

MadeinIsrael

MAC:0002C902004C

S/N:MT0924X00266

ManagementMAC:

0002C902004C

Installation Safety Warnings

Rev 1.2

Mellanox Technologies

12

2 Installation Safety Warnings

Warnings in French can be found on page 43. Warnings in German can be found on page 46.

Warnings in Spanish can be found on page 50.

1. Installation Instructions

2. Over-temperature

3. Stacking the Chassis

4. Double pole / Neutral Fusing

5. During Lightning - Electrical Hazard

6. Copper Cable Connecting/Disconnecting

Read all installation instructions before connecting the equipment to the power source.

This equipment should not be operated in an area with an ambient temperature exceed-

ing the maximum recommended: 45°C (113°F). Moreover, to guarantee proper air

flow, allow at least 8cm (3 inches) of clearance around the ventilation openings.

The chassis should not be stacked on any other equipment. If the chassis falls, it can

cause bodily injury and equipment damage.

This system has double pole/neutral fusing. Remove all power cords before opening

the cover of this product or touching any internal parts.

During periods of lightning activity, do not work on the equipment or connect or dis-

connect cables.

Copper cables are heavy and not flexible, as such they should be carefully attached to

or detached from the connectors. Refer to the cable manufacturer for special warnings/

instructions.

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

13

7. Rack Mounting and Servicing

8. High Leakage Current

9. Connect a Valid Ground to this Device

10. Equipment Installation

11. Equipment Disposal

12. Local and National Electrical Codes

13. Installation Codes

When this product is mounted or serviced in a rack, special precautions must be taken

to ensure that the system remains stable. In general you should fill the rack with equip-

ment starting from the bottom to the top.

WARNING: High leakage current; Earth connection essential before connecting sup-

ply.

Before connecting this device to the power line, the protective earth terminal

screws of this device must be connected to the protective earth in the building

installation.

This equipment should be installed, replaced, and/or serviced only by trained and qual-

ified personnel.

Disposal of this equipment should be in accordance to all national laws and regula-

tions.

This equipment should be installed in compliance with local and national electrical

codes.

This device must be installed according to the latest version of the country

national electrical codes. For North America, equipment must be installed in

accordance to the applicable requirements in the US National Electrical Code

and the Canadian Electrical Code.

Installation Safety Warnings

Rev 1.2

Mellanox Technologies

14

14. Interconnection Of Units

15. Suitable Enclosure

16. UL Listed and CSA Certified Power Supply Cord

17. Do Not Use the Switch as a Shelf or Work Space.

18. WEEE Directive

Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL

certified type DP-1 or DP-2. (Note- when residing in non LPS circuit)

Overcurrent Protection: A readily accessible Listed branch circuit overcurrent

protective device rated 20 A must be incorporated in the building wiring.

Suitable electrical, mechanical and fire enclosure shall be provided by the 

end product manufacturer and or the end user.

For North American power connection, select a power supply cord that is UL Listed

and CSA Certified, 3 - conductor, [16 AWG], terminated with a molded plug rated at

125 V, [13 A], with a minimum length of 1.5m [six feet] but no longer than 4.5m.

For European connection, select a power supply cord that is internationally 

harmonized and marked “<HAR>”, 3 - conductor, minimum 1.0 mm 2 wire,

rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug

rated at 250 V, 10 A.

Caution: Slide/rail mounted equipment is not to be used as a shelf or a work space. The

rails are not intended for sliding the unit away from the rack. It is for permanent instal-

lation at final resting place only, not used for service and maintenance.

According to the WEEE Directive 2002/96/EC, all waste electrical and electronic

equipment (EEE) should be collected separately and not disposed of with regular

household waste.

Dispose of this product and all of its parts in a responsible and environmentally

friendly way.

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

15

3 Hardware Basic Operation and Installation

3.1 Switch Platform Hardware Overview

Figure 4 shows the front view of the switch. The figure shows port configurations for the switch

systems, interface connectors, and various status LEDs.

Figure 4: Switch System Front Panel

All connectivity is via the connector side panel. All connectors can support active cables.

3.1.1 LED Assignments

3.1.1.1 System Status Indicators

The System Status Indicators are located on the left side of the front (connector side) panel. The

system status indicators should display as follows:

When the switch is plugged in, within four minutes the following LEDs should be evident.

•The Status LED should light up green.

• The Fan LED should light up green.

• The Bad Port LED should be off.

• The Unit ID LED should be off.

Figure 5: Status LEDs

SX1016

UID

Mellanox

RST

UID

RST

Hardware Basic Operation and Installation

Rev 1.2

Mellanox Technologies

16

3.1.1.2 Status LED

The status indicator is located on the left side of the front panel (connector side) of the unit. The

following status conditions are possible:

Table 3 - Switch Status LED Configurations

3.1.1.3 Fan Indicators

The fan indicator is located on the left side of the front panel (connector side) of the unit. The fol-

lowing fan status conditions are possible:

Table 4 - Fan LED Configurations

If the status LED shows red after four minutes unplug the switch and call your Mella-

nox representative for assistance.

If the fan LED shows red unplug the switch and call your Mellanox representative for

assistance.

If the switch shuts down due to over-temperature, unplug the switch, wait 5 minutes

and replug in the switch. For more information See “Troubleshooting” on page 31.

LED Configuration LED Description

Off No power to the switch.

Solid Green OK – the switch is running.

All OK.

Blinking Green Switch is booting up.

Red Error – there is a problem with power output from the power supply, or there is a

thermal shut down.

LED Configuration FAN LED

Off There is no power to the fans.

Green OK – the fans are running.

Red Error – the fans are not operating properly. Replace the switch.

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

17

3.1.1.4 Bad Port LED

The bad port indicator is located on the left side of the front panel (connector side) of the unit.

The following bad port conditions are possible:

Table 5 - Bad Port LED Configurations

This LED shows symbol errors. Possible causes for this are:

•bad cable

• bad connection

• bad connector

This LED lights up when one or more ports is receiving a symbol error. The LED immediately

goes off until the next symbol error is received.

3.1.1.5 UID LED Switch Identifier

The UID LED is a debug feature that will become available to customers in the near future. For

details please contact Mellanox Technologies support.

3.1.1.6 Port Connector LED

The port LEDs are assigned to the ports as in figure:

Fans must be operating while the power supply is plugged in.

If the switch shuts down due to over-temperature, unplug the switch, wait 5 minutes

and replug in the switch. For more information See “Troubleshooting” on page 31.

LED Configuration Description

Off OK – all ports are up and running.

Flashing Orange Error – one or possibly more ports has just received a symbol error.

Hardware Basic Operation and Installation

Rev 1.2

Mellanox Technologies

18

3.1.2 Port Connector LED Assignment

Figure 6: LED to Port Assignment

Between the top two ports is a row of LEDs. The left LED is for the top port in the column, the

middle LED is for the center port in the column and the right LED is for the bottom port in the

column. Some versions of this switch have a fourth LED. When there are four LEDs, the second

from the left will be disabled.

Table 6 - Port Connector Physical and Logical Link Indications

This LED when flashing orange shows port physical errors. Possible causes for this are:

•bad cable

• bad connection

• bad connector

•bad cage

3.2 Air Flow

These switches can come with two air flow patterns. The two patterns are:

• power supply side inlet to connector side outlet

• connector side inlet to power supply side outlet

The air flow is specified in the product model number. See “Mellanox Part Numbering Legend”

on page 9.

3.3 SFP+ Cable Power Budget Classification

This switch is designed for active cables with a max power per module of 1.0W.

LED Configuration LED Description

Off Physical link down / Default

Solid Green Physical link up no traffic

Flashing Green Physical link up with traffic

Flashing Orange Physical errors

RST

UID

SwitchX® 64 Port SFP+ Ethernet Switch Hardware User Manual Rev 1.2

Mellanox Technologies

19

3.4 Interfaces

3.4.1 Port Connector Interfaces

The Connector side of the switch has 64 SFP+ 10

Figure 7: Port Numbering

3.5 Management and Firmware Updating Interfaces

There are two interfaces to connect to the SX1016:

• 1 X 100M/1Gb Ethernet connectors labelled

• 1 connector that is labelled Use this RJ-45 connector to connect to the host PC

Figure 8: Management Interfaces

3.5.1 RJ-45 Console Connector

The port labelled is for a local host connection to the management module. This is used

the first time the switch is connected. A harness is included in the package to connect to a DB9

connection on a host PC. Before any remote management is available you must connect to a local

host PC and follow the instructions in the Installation Guide, “Configuring the Switch for the

First Time”. For the Socket pinout see “RJ45 CONSOLE and Ethernet Interfaces” on page 51.

3.5.2 Mini USB

This interface can be used to update SW.

3.5.3 RJ-45 Ethernet Connector

The Ethernet connection labelled provides access for remote management. The switch

can be connected to any Ethernet port.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

SX1016

Mellanox

Hardware Basic Operation and Installation

Rev 1.2

Mellanox Technologies

20

3.5.4 I2C Connector

There is an “I2C”interface on the side panel. This interface is only for FAEs and advanced users.

Warning: Any red status LED is cause for concern and must be dealt with immediately.

It can take up to 4 minutes to boot up, during which time the status LED may indicate

red.

La page charge ...

Mellanox Technologies SwitchX MSX1016X-2BFR Hardware User Manual

Ce manuel convient également à

Mellanox Technologies SwitchX MSX1016X-2BFR Hardware User Manual

dans d''autres langues

Documents connexes

Autres documents