Mellanox Technologies SFP+ Manuel utilisateur

Marque: Mellanox Technologies

Modèle: SFP+

Taper: Manuel utilisateur

Ce manuel convient également à

www.mellanox.com

ConnectX

-2 VPI Dual Port QSFP and SFP+

Card User’s Manual

P/N: MHZH29-XTR, MHZH29-XSR

Rev 1.0

Mellanox Technologies

350 Oakmead Parkway

Sunnyvale, CA 94085

U.S.A.

www.mellanox.com

Tel: (408) 970-3400

Fax: (408) 970-3403

Mellanox Technologies, Ltd.

PO Box 586 Hermon Building

Yokneam 20692

Israel

Tel: +972-4-909-7200

Fax: +972-4-959-3245

Mellanox®, ConnectX®, InfiniBlast®, InfiniBridge®, InfiniHost®, InfiniRISC®, InfiniScale®, and InfiniPCI® are registered

trademarks of Mellanox Technologies, Ltd.

BridgeX and Virtual Protocol Interconnect are trademarks of Mellanox Technologies, Ltd.

All other marks and names mentioned herein may be trademarks of their respective companies.

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual

Document Number: 3157

Rev 1.0

Mellanox Technologies

NOTE:

THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED DOCUMENTA-

TION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY KIND AND

SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PROD

UCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT HAS NOT

MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE PRODUCTO(S) AND/OR

THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT AND DOES NOT GUARANTEE

OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST QUALITY. ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT

ABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED. IN NO EVENT

SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT, INDIRECT, SPE

CIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING, BUT NOT LIMITED TO, PAY-

MENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR

BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CON

TRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY

FROM THE USE OF THE PRODUCT(S) AND RELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBIL

ITY OF SUCH DAMAGE.

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

Table of Contents

Table of Contents 3

List of Figures 4

List of Tables 5

Revision History 6

About this Manual 7

Chapter 1 Overview 8

1.1 Adapter Cards 8

1.2 Mellanox Part Numbering Legend 9

1.3 Finding the GUID/MAC and Serial Number on the Adapter Cards 10

Chapter 2 VPI Adapter Card Installation 12

2.1 Hardware and Software Requirements 12

2.2 Installation Instructions 12

2.3 Safety Warnings 12

2.4 Cables and Modules 13

2.5 Cable Lengths 16

Chapter 3 Driver Software and Firmware 17

3.1 Driver Software 17

3.2 Updating Adapter Card Firmware 17

3.3 Single Adapter Card Firmware Update 17

Chapter 4 Adapter Card Interfaces 18

4.1 I/O Interfaces 18

4.2 Power 20

4.3 Memory 20

4.4 VPD Layout for these Adapter Cards 21

Chapter 5 Replacing a Tall Bracket With a Short Bracket 23

5.1 Remove the Existing Bracket from the Adapter Card 23

5.2 Installing the New Bracket 23

Appendix A Specifications 25

A.1 Board Mechanical Drawing and Dimensions 25

A.2 EMC Certification Statements 26

A.3 MHZH29-X[ST]R Specifications 28

Appendix B Interface Connectors Pinout 29

B.1 I2C-Compatible Connector Pinout 29

B.2 PCI Express x8 Connector Pinout 29

B.3 QSFP Connector Pinout 30

B.4 SFP+ Connector Pinout 32

Appendix C Avertissements de sécurité d’installation (Warnings in French) 34

Appendix D Sicherheitshinweise (Warnings in German) 36

Rev 1.0

Mellanox Technologies

List of Figures

Figure 1: Component Side 9

Figure 2: Card Product Label 11

Figure 3: SFP+ Transceiver Module 14

Figure 4: Module With Locking Mechanism Closed 14

Figure 5: Module With Locking Mechanism Open 14

Figure 6: Connector Orientation 15

Figure 7: Port Numbering 18

Figure 8: Physical and Logical Link Indications 19

Figure 9: I2C Connector 20

Figure 10: Flash Jumper 20

Figure 11: Adapter Card 23

Figure 12: Placing the Bracket on the Card 24

Figure 13: Schematic of the ConnectX-2 MHZH Adapter Card 25

Figure 14: Compatible Connector Plug and Pinout 29

Figure 15: Connector and Cage Views 31

Figure 16: Rear View of Module With Pin Placement 32

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

List of Tables

Table 1: Revision History Table 6

Table 2: Documents List 7

Table 3: Mellanox Cards Part Numbering Key 9

Table 4: Hardware and Software Requirements 12

Table 5: Jumper Configuration 20

Table 6: Specifications for MHZH29-XTR 28

Table 7: I2C-compatible Connector Pinout 29

Table 8: SFP+ Connector Pinout 33

Rev 1.0

Mellanox Technologies

Revision History

This document was printed on 11/3/09.

Table 1 - Revision History Table

Date Rev Comments/Changes

October

2009

1.0 Initial Release

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

About this Manual

This User’s Manual describes Mellanox Technologies ConnectX

-2 VPI IB and Ethernet PCI

Express x8 adapter cards. It provides details as to the interfaces of the board, specifications,

required software and firmware for operating the board, and relevant documentation.

Intended Audience

This manual is intended for the installer and user of these cards.

The manual assumes basic familiarity with InfiniBand® and Ethernet networks and architecture

specifications.

Related Documentation

Table 2 - Documents List

Online Resources

• Mellanox Technologies Web pages: http://www.mellanox.com

• Mellanox Technologies Firmware download Web page:

http://www.mellanox.com

=> Downloads => Firmware

Document Conventions

When discussing memory sizes, MB and MBytes are used in this document to mean size in mega

bytes. The use of Mb or Mbits (small b) indicates size in mega bits.

Mellanox Firmware Tools (MFT) User’s

Manual

Document no. 2204UG

User’s Manual describing the set of MFT firmware management

tools for a single InfiniBand node.

See http://www.mellanox.com > Downloads > Firmware Tools

IBTA Specification Release 1.2.1 InfiniBand Architecture Specification

IEEE Std 802.3 Specification This is the IEEE Ethernet specification

http://standards.ieee.org/getieee802

PCI Express 2.0 Specifications Industry Standard PCI Express 2.0 Card Electromechanical Speci-

fication, Rev 1.3.

OverviewRev 1.0

Mellanox Technologies

1 Overview

This document is a User’s Manual for Mellanox Technologies network VPI adapter cards based on

the MT25408 ConnectX

-2 VPI integrated circuit device. The cards described in this manual have

the following main features:

• IBTA v1.2.1 compliant

• IEEE Std 802.3 compliant

• QSFP port for connecting InfiniBand traffic at 10Gb/s (SDR), 20Gb/s (DDR), or 40Gb/s (QDR)

• SFP+ port for connecting Ethernet traffic at 10 Gb/s

• Compliant with QSFP MSA spec Rev. 1.0

• Compatible with copper cables and optical cables with the use of QSFP and SFP+ connectors

• PCI Express 2.0 (1.1 compatible) through an x8 edge connector up to 5GT/s

• ‘Media detect circuit’ with powered connector support for the use of active cables and external

PHY fiber solutions

• EU Restriction of Hazardous Substances (RoHS) compliant

• 10 Gb/s Ethernet

1.1 Adapter Cards

The MHZH29 card is a VPI adapter card with a 40Gb/s InfiniBand QSFP connector and a 10GigE

SFP+ connector.

The QSFP connector is compatible with:

• Gigabit Ethernet

• InfiniBand Architecture Specifications

•Fibre Channel

The SFP+ connector is compatible with 10GigE.

Table 3 lists the VPI adapter cards described in this manual.

Table 3 - Adapter Cards List

Ordering Part

Number (OPN)

IB QSFP

Port Speed

ETH SFP+

Port Speed

Short /

Tall

Bracket

RoHS

Adapter IC

Part Number

MHZH29-XTR 40Gb/s (QDR) 10Gb/s Tall RoHS-R6 MT25408B0-FCCR-QI

MHZH29-XSR 40Gb/s (QDR) 10Gb/s Short RoHS-R6 MT25408B0-FCCR-QI

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

Figure 1: Component Side

1.2 Mellanox Part Numbering Legend

Table 4 describes the Mellanox Technologies adapter cards part numbering legend.

Table 4 - Mellanox Cards Part Numbering Key

Adapter Card

OPN

MHTS#I-XBR

Field Decoder

M Mellanox

Technolo-

gies

H Adapter

Type

H = InfiniBand Host Channel Adapter, N = Ethernet Network Interface Card,

T Media E = CX4 SDR, G = CX4 DDR, J = CX4 QDR,

Q = QSFP QDR, R = QSFP DDR, T = UTP,

Z = one SFP+ connector and one QSFP connector

S Silicon

H = ConnectX

, S = InfiniHost III Lx

, T= InfiniHost

,A = InfiniHost III Ex,

S = InfiniHost III Lx, T = InfiniHost

# # ports 1 = 1, 2 = 2,

OverviewRev 1.0

Mellanox Technologies

For example, the part number MHZH29-XTR describes Mellanox Technologies’ ConnectX-2 card

with dual ports one SFP+ and one QSFP, a PCIe2.0 x8 5.0GT/s interface, no on-board memory

(mem-free), a short PCI bracket, and RoHS R5 compliance. Using the legend,

• field M = M to indicate a Mellanox Technologies product,

• field H = H to indicate an InfiniBand Adapter Card,

• field T = Z to indicate QSFP (IB QDR) and SFP+ (10GigE),

• field S = H to indicate the ConnectX family,

• field # = 2 to indicate two ports,

• field I = 9 to indicate PCI Express 2.0 x8 running at 5.0GT/s,

• field X = X to indicate no on-board memory,

• field B = T to indicate a tall bracket, and

• field R = R to indicate RoHS R6 (lead free) compliance

1.3 Finding the GUID/MAC and Serial Number on the Adapter Cards

All Mellanox adapter cards have a label on the printed side of the adapter card that has the card

serial number, the card MAC for Ethernet protocol and the card GUID for InfiniBand protocol.

VPI Cards have both a MAC and a GUID.

IHost Inter-

face

X = PCI-X, 4 = PCIe x4, 8 = PCIe x8, 9 = PCIe (SerDes @ 5.0 GT/s)

G Generation <blank> = Initial product generation

- Separator

XMemory

Size

X = MemFree, 1=128MB, 2=256MB, 3=512MB

B Bracket S = Short, T = Tall, N = None

R RoHS <blank> = non RoHS, C = RoHS R-5 w/ Exemption, R = RoHS R-6 Lead-Free

Table 4 - Mellanox Cards Part Numbering Key

Adapter Card

OPN

MHTS#I-XBR

Field Decoder

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

Figure 2: Card Product Label

S/N:MT0744X00012

P/N:MHZH29-XTR

GUID: 0002C9030005646 C

Made in IL

REV: X1

MAC: 0002C901122642 FC

VPI Adapter Card InstallationRev 1.0

Mellanox Technologies

2 VPI Adapter Card Installation

2.1 Hardware and Software Requirements

Before installing the adapter card, please make sure that the system meets the hardware and soft-

ware requirements listed in Table 5, “Hardware and Software Requirements”. Refer to Chapter

3,“Driver Software and Firmware” on page 17 for download and installation instructions.

2.2 Installation Instructions

Read all installation instructions before connecting the equipment to the power source.

2.2.1 Installation Instructions as per Host Machine

The adapter cards listed in Table 3 on page 8 are standard PCI Express cards, each with a standard

x8 edge connector. Please consult the host machine documentation for instructions on how to

install a PCI Express card.

2.3 Safety Warnings

1. Installation Instructions

2. Over-temperature

Table 5 - Hardware and Software Requirements

Requirement Description

Hardware PCI Express x8 or x16 slots

Software

Operating

Systems/Distributions

• For Windows

• IB see http://www.mellanox.com => Downloads => InfiniBand

SW/ Windows Drivers

• Ethernet see http://www.mellanox.com => Downloads => Ethernet

SW/ Windows Drivers

• For Linux, both the InfiniBand and Ethernet drivers are in the Mellanox OpenFab-

rics Enterprise Distribution (OFED) software package available via the Mellanox

OpenFabrics Web site

http://www.mellanox.com => Downloads => InfiniBand/VPI SW/ Linux Drivers

Read all installation instructions before connecting the equipment to the power

source.

This equipment should not be operated in an area with an ambient temperature

exceeding the maximum recommended: 55°C (131°F).

To guarantee proper air flow, allow at least 8cm (3 inches) of clearance around

the ventilation openings.

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

3. During Lightning - Electrical Hazard

4. Copper InfiniBand Cable Connecting/Disconnecting

5. Equipment Installation

6. Equipment Disposal

7. Local and National Electrical Codes

8. Exposure to Radiation

2.4 Cables and Modules

This card can be connected using direct copper cables or optical cables using an SFP+ transceiver

module. Copper cables can be both active and passive.

During periods of lightning activity, do not work on the equipment or connect

or disconnect cables.

Copper InfiniBand cables are heavy and not flexible, as such they should be

carefully attached to or detached from the connectors. Refer to the cable manu-

facturer for special warnings and instructions.

This equipment should be installed, replaced, or serviced only by trained and

qualified personnel.

Disposal of this equipment should be in accordance to all national laws and

regulations.

This equipment should be installed in compliance with local and national elec-

trical codes.

Caution – Use of controls or adjustment or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

CLASS 1 LASER PRODUCT and reference to the most recent laser standards

IEC 60 825-1:1993 + A1:1997 + A2:2001 and EN 60825-1:1994+A1:1996+

A2:2001

VPI Adapter Card InstallationRev 1.0

Mellanox Technologies

The adapter cards are shipped without optical modules. Approved modules must be purchased

from Mellanox. The OPNs for the approved Mellanox modules are MFM1T02A-SR and

MFM1T02A-LR. The figure below shows the Mellanox approved SFP+ module.

Note: SR and LR modules not recommended by Mellanox may not work with the adapter.

Figure 3: SFP+ Transceiver Module

2.4.1 Inserting the Optical Transceiver Module

To insert the module into the cage:

1. Open the module’s locking mechanism – see Figure 4 and Figure 5.

2. Make sure that the male connectors on the module will align with the female connectors inside

of the cage. Also check that there is no dirt or foreign matter in the module or in the cage.

Figure 4: Module With Locking Mechanism Closed

Figure 5: Module With Locking Mechanism Open

3. Insert the module into the adapter card module cage.

4. Close the locking Mechanism.

To remove the module from the cage:

1. Unlock the locking mechanism by opening the handle.

2. Pull the module out of the cage.

2.4.2 Cable Installation

All cables can be inserted or removed with the unit powered on. To insert a cable, press the con-

nector into the port receptacle until the connector is firmly seated. The GREEN LED indicator will

light when the physical connection is established (that is, when the unit is powered on and a cable

is plugged into the port with the other end of the connector plugged into a functioning port). After

plugging in a cable, lock the connector using the latching mechanism particular to the cable ven-

dor. When a logical connection is made the YELLOW LED will come on. When data is being

transferred the YELLOW LED will blink.

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

Note: When installing cables make sure that the latches engage.

Note: Always install and remove cables by pushing or pulling the cable and connector in a

straight line with the card.

To remove a cable, disengage the locks and slowly pull the connector away from the port recepta-

cle. Both LED indicators will turn off when the cable is unseated.

2.4.2.1 Inserting a Cable into the Adapter Card

1. Support the weight of the cable before connecting the cable to the adapter card. Do this by using

a cable holder or tying the cable to the rack.

2. Determine the correct orientation of the connector to the card before inserting the connector. Do

not try and insert the connector up side down. This may damage the adapter card.

3. Insert the connector into the adapter card. Be careful to insert the connector straight into the

cage. Do not apply any torque, up or down, to the connector cage in the adapter.

4. Make sure that the connector locks in place.

Figure 6: Connector Orientation

2.4.2.2 Removing a Cable from the Adapter Card

1. Pull on the latch release mechanism thereby unlatching the connector and pull the connector out

of the cage.

2. Do not apply torque to the connector when removing it from the adapter card.

Cables, especially long copper cables, can weigh a substantial amount. Make

sure that the weight of the cable is supported on its own and is not hanging

from the adapter card.

180

Tie the

Cable to the

Rack

VPI Adapter Card InstallationRev 1.0

Mellanox Technologies

3. Remove any cable supports that were used to support the cable’s weight.

2.5 Cable Lengths

Mellanox Cards support up to 40 Gb/s IB and Ethernet over the QSFP port, and up to 10Gb/s on

the SFP+ connector.

2.5.1 InfiniBand Connectivity

These Mellanox Cards support QSFP passive copper connectivity up to 7 meters, and active cable

support up to 50 meters.

2.5.2 Ethernet Connectivity

These Mellanox Cards support ethernet connectivity as defined in IEEE Std 802.3. ae standard.

The described adapter cards can be connected to switches and routers using cable lengths as speci-

fied in the tables below.

These cards are able to support direct attached copper cables. Check www.mellanox.com => Prod-

ucts => Cables for cable recommendations regarding direct attached copper cables.

Table 6 - Max SR Cable Lengths

Cable Max Length of Approved Cable

OM-2 82m

OM-3 330m

Table 7 - Max LR Cable Lengths

Cable Max Length of Approved Cable

SMF 10 Km

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

3 Driver Software and Firmware

3.1 Driver Software

For Linux, download and install the latest OpenFabrics Enterprise Distribution (OFED) software

package available via the Mellanox OpenFabrics Web site at:

http://www.mellanox.com => Downloads => InfiniBand/VPI SW/Drivers. Follow the installation

instructions included in the download package.

3.2 Updating Adapter Card Firmware

Each card is shipped with the latest version of qualified firmware at the time of manufacturing.

Firmware is updated occasionally, and the most recent firmware can be obtained from

http://www.mellanox.com => Downloads => Firmware.

3.3 Single Adapter Card Firmware Update

Firmware can be updated on the stand alone single card using the flint tool of the Mellanox Firm-

ware Tools (MFT) package. This package is available for download, along with its user’s manual,

from the Mellanox Firmware Tools page. See http://www.mellanox.com => Downloads => Firm-

ware Tools.

A firmware binaries table lists a binary file per adapter card. The file name of each such binary is

composed by combining the firmware name, the firmware release version, and the card part num-

ber. Please contact Mellanox or your assigned Field Application Engineer if you cannot find the

firmware binary for your adapter card. This may happen if the product is not yet available for gen-

eral distribution.

Adapter Card InterfacesRev 1.0

Mellanox Technologies

4 Adapter Card Interfaces

4.1 I/O Interfaces

Each adapter card includes the following interfaces:

• QSFP Optical Connector

• SFP+ Ethernet Connector

• PCI Express x8 edge connector

• I/O panel LEDs

•I

C compatible connector (for debug)

Port 1 connects to the IB port of the device, while port 2 connects to the Ethernet port of the

device. See Figure 7,“Port Numbering”

Figure 7: Port Numbering

4.1.1 InfiniBand Interface

The ConnectX-2 VPI device (MT25408B0) is compliant with the InfiniBand Architecture Specifi-

cation, Release 1.2.1. It has a compliant 4X InfiniBand port, with four Tx/Rx pairs of SerDes.

Each of the VPI adapter cards (listed in Table 3 on page 8) based on this device provides access to

its port by means of a QSFP connector.

This port utilizes a ‘media detect circuit’ that supports active copper cables and fiber solutions to

be connected to the InfiniBand port connectors.

4.1.2 Ethernet SFP+ Interface

The ConnectX

-2 device is compliant with the IEEE Std 802.3ae 10 Gigabit Ethernet and the

IEEE Std 802.3aq 10GBASE LRM. The SFP+ port has one Tx/Rx pair of SerDes. Each of the cards

(listed in Table 3 on page 8) based on this device provides access to their Ethernet port by means

of copper or optical cables.

Port 2

Ethernet

Port 1

IB port

ConnectX-2 VPI InfiniBand and Ethernet Adapter Card User’s Manual Rev 1.0

Mellanox Technologies

4.1.3 PCI Express Interface

The ConnectX-2 adapter cards support PCI Express 2.0 (1.1 compatible) through an x8 edge con-

nector.

4.1.4 LED Assignment

The board has I/O LEDs located on the I/O panel. The green LED, when lit, indicates that the

driver is running and a valid physical connection between nodes exists. If the green LED is blink-

ing, it indicates a problem with the physical link. The yellow LED when lit, indicates a valid data

activity link, this is the logical link. The yellow LED illuminates when the network is discovered

over the physical link. A valid data activity link without data transfer is designated by a constant

yellow LED indication. A valid data activity link with data transfer is designated by a blinking yel-

low LED indication. If the LEDs are not active, either the physical link or the logical link (or both)

connections have not been established.

Figure 8: Physical and Logical Link Indications

Note: The short bracket has the same port and LED footprint as the tall bracket.

4.1.5 I

C Compatible Interface

A three-pin header on the adapter card is provided as the I

C compatible interface. See

Figure 13,“Schematic of the ConnectX-2 MHZH Adapter Card” for the location on the board.

Table 8 - LEDs

Port Number LED Name

Port 1 Physical Link - Green

Constant on indicates a good physical link

Blinking indicates a problem with the

Physical link

Data Activity - Yellow

Blinking indicates Data Transfer

Constant on indicates no Data Transfer

Port 2 Physical Link - Green

Constant on indicates a good physical link

Blinking indicates a problem with the

Physical link

Data Activity - Yellow

Blinking indicates Data Transfer

Constant on indicates no Data Transfer

Port 1

Port 2

Adapter Card InterfacesRev 1.0

Mellanox Technologies

Figure 9: I

C Connector

4.2 Power

All adapter cards receive 12V and 3.3V power from the PCI Express Edge connector. All other

required power voltages are generated by on-board switch mode regulators. See “Specifications”

on page 25.

4.3 Memory

The adapter cards support multiple memory devices through the PCI Flash, and I2C-compatible

interfaces. The adapter card utilizes the PCI Express interface to store and access IB fabric and/or

EN fabric connection information and packet data on the system memory.

4.3.1 Flash

Each of the adapter cards include one 16MB SPI Flash device M25P16-VME6G device by ST

Microelectronics) accessible via the Flash interface of the MT25408B0 ConnectX-2 VPI device.

There is a jumper on each adapter card that indicates to the device whether an on-board Flash

device is to be used. Table 9 provides information on this jumper. See Figure 13,“Schematic of the

ConnectX-2 MHZH Adapter Card” for the jumper location.

4.3.2 EEPROM

Each board incorporates an EEPROM that is accessible through the I2C-compatible interface. The

EEPROM is used for storing the Vital Product Data (VPD). The VPD format adheres to the PCI

Local Bus Specification Rev 2.3 VPD definition. The EEPROM capacity is 4Kb.

Table 9 - Jumper Configuration

Description Option

Card Default

Configuration

Comments

Flash present/

not present

connection open – Flash present

connection shorted – Flash not present

Figure 10:

Flash Jumper

connection

open – Flash

present

Header 1x2

La page charge ...

Mellanox Technologies SFP+ Manuel utilisateur

Marque: Mellanox Technologies

Modèle: SFP+

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Mellanox Technologies SFP+ User manual

Mellanox Technologies SFP+ Manuel utilisateur

Ce manuel convient également à

Mellanox Technologies SFP+ Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents