Taco Comfort Solutions VR1816HY2FC2A00 Mode d'emploi

Marque: Taco Comfort Solutions

Modèle: VR1816HY2FC2A00

Taper: Mode d'emploi

00e

series VR1816

Instruction Sheet

102-499

SUPERSEDES: February 11, 2016 EFFECTIVE: April 26, 2017

Plant ID No. 001-4230

Infinitely Variable Speed, ECM High-Efficiency Circulator

DESCRIPTION:

The 00e

series VR1816 circulator is an infinitely variable speed wet rotor circulator with an ECM,

permanent magnet motor. Operating modes include infinitely adjustable fixed speed or self-adjust-

ing proportional or constant pressure variable speed. Its high efficiency motor reduces power con-

sumption by up to 85% compared to equivalent AC permanent split capacitor circulators.

APPLICATION:

• Maximum operating pressure: 125 psi (8.6 bar)

• Maximum water temperature: 230°F (110ºC)

• Electrical specifications:

Voltage: 110-120V, 50/60 Hz, single phase

Maximum operating power: 44W

Maximum amp rating: 0.54

• Equipped with a cast iron casing and should be used for closed loop systems only

• Not suitable for open loop potable water or chilled water systems

• Taco circulator pumps are for indoor use only – employer uniquement a l’interieur

• Acceptable for use with water or maximum of 50% water/glycol solution

FEATURES:

• 3 operating modes:

- Fixed speed ( ) - infinitely adjustable MIN/MAX settings

- Constant pressure ( ), variable speed - 3 constant pressure differential curves

(5, 10, or 15 maximum feet of head)

- Proportional pressure ( ), variable speed - 3 variable pressure differential curves

(High, Med, or Low)

• Multi-color LED display showing operating mode and error code diagnostics

• Use with a Taco ZVC Zone Valve Control or SR Switching Relay for ON/OFF operation

• Nut capture feature on flanges for easier fit up

• Dual electrical knockouts and 6” stranded wire leads for easy wiring

• Double insulated - no ground-wire required

• Whisper quiet operation

• BIO Barrier

protects the pump from system contaminants

• SureStart

- automatic unblocking and air purging mode

• Optional 2-way flange model for easy fit-up to any flange orientation

• Integral Flow Check (IFC

) included - Field installed

INSTALLATION:

WARNING: Do not use in swimming pool or spa areas. Pump has not been investigated for these applications.

AVERTISSEMENT: Ne pas utiliser dans une piscine ou un spa. La pompe n'a pas été étudiée pour ces applications.

CAUTION: The addition of petroleum based fluids or certain chemical additives to systems using TACO equipment voids the warranty.

Consult factory for fluid compatibility.

ATTENTION: L'ajout de liquides à base de pétrole ou de certains additifs chimiques à des systèmes utilisant un équipement TACO annule

la garantie. Consultez le fabricant pour connaître la compatibilité de liquides.

CAUTION: Installations at elevations over 5000 feet must have higher fill pressure of 20 psi minimum to prevent pump cavitation and flash-

ing. Premature failure may result. Adjust expansion tank pressure to equal fill pressure. A larger size expansion tank may be required.

ATTENTION: Des installations à des altitudes de plus de 1600 mètres doivent présenter une pression de remplissage plus élevée de 20

psi au minimum afin d'éviter toute cavitation ou flashing de la pompe. Une défaillance prématurée peut en résulter. Réglez la pression du

réservoir d'expansion de façon qu'elle soit égale à la pression de remplissage. Un réservoir d'expansion d'une taille supérieure peut être

nécessaire.

Figure 1:

Standard flange model:

VR1816-HY2-FC2A00

Optional 2-way flange model:

VR1816-HY2-4C2A00

KEY:

VI, V2, V3 = SHUT-OFF ISOLATION VALVE

P = TACO CIRCULATOR WITH IFC

FF = FAST FILL BOILER FEED VALVE

PV4 = PURGE VALVE

RECOMMENDED PURGING STEPS:

1. CLOSE V1, PV4, V2

2. OPEN V3

3. OPEN FF VALVE

4. OPEN V2, PV4, TO PURGE LAST ZONE

FIRST (ZONE 3)

5. CLOSE FF VALVE

6. CLOSE V2, PV4

7. REPEAT STEPS 1 TO 6 FOR EACH

ADDITIONAL ZONE, PURGE ZONE 1 LAST

8. OPEN V1 WHEN ALL ZONES ARE

PURGED

9. ADJUST SYSTEM TO DESIRED OPERATING

FILL PRESSURE IF REQUIRED

BOILER

EXPANSION

TANK

ZONE 1ZONE 2

PV4

MULTI-SPEED MODE

PREFERRED PIPING

FOR CIRCULATORS

ON BOILER SUPPLY

ZONE 1

ZONE 3

ZONE 2

ZONE 3

• AIR PURGING SEQUENCE

BY ZONE

LAST FIRST

BOILER

EXPANSION

TANK

ZONE

PV4

ALTERNATE PIPING

FOR CIRCULATORS

ON BOILER RETURN

ZONE 1ZONE 2

V2V2

V3V3

ZONE

ZONE 3

• AIR PURGING

SEQUENCE

BY ZONE

LAST FIRST

Figure 2:

BOILER

EXPANSION

TANK

ZONE 1ZONE 2

PV4

MULTI-SPEED OR VARIABLE SPEED MODES

PREFERRED PIPING

FOR ZONE VALVES

ON BOILER SUPPLY

ZONE 1

ZONE 3

ZONE 2

ZONE 3

• AIR PURGING SEQUENCE

BY ZONE

LAST FIRST

BOILER

EXPANSION

TANK

ZONE

PV4

ALTERNATE PIPING

FOR ZONE VALVES

ON BOILER RETURN

ZONE 1ZONE 2

V2V2

V3V3

ZONE

ZONE 3

• AIR PURGING

SEQUENCE

BY ZONE

LAST FIRST

ZV3 ZV2 ZV1

ZV1 ZV2 ZV3

KEY:

VI, V2, V3 = SHUT-OFF ISOLATION VALVE

P = TACO CIRCULATOR WITHOUT IFC INSTALLED

FF = FAST FILL BOILER FEED VALVE

PV4 = PURGE VALVE

ZV = ZONE VALVE

RECOMMENDED PURGING STEPS:

1. CLOSE V1, PV4, V2

2. OPEN V3 AND ZV3

3. OPEN FF VALVE

4. OPEN V2, PV4, TO PURGE LAST ZONE

FIRST (ZONE 3)

5. CLOSE FF VALVE

6. CLOSE V2, PV4

7. REPEAT STEPS 1 TO 6 FOR EACH

ADDITIONAL ZONE, PURGE ZONE 1 LAST

8. OPEN V1 WHEN ALL ZONES ARE

PURGED

9. ADJUST SYSTEM TO DESIRED OPERATING

FILL PRESSURE IF REQUIRED

10. MOVE ALL ZV TO CLOSED/AUTOMATIC

POSITION

Figure 3:

ACCEPTABLE MOTOR MOUNTING POSITIONS

WARNING: Use supply wires suitable for 90°C. AVERTISSEMENT: Employer des fils d’alimentation adeqauts pour 90°C.

1. Location: The circulator can be installed on the supply or return side of the boiler but for best system performance, it should always

pump away from the expansion tank. See piping diagrams in Figure 2 and Figure 3.

2. Mounting position: Circulator must be mounted with the motor in the horizontal position. See diagrams below for acceptable motor

mounting orientations.

3. Filling the system: Fill the system with tap water or a maximum of 50% propylene-glycol and water solution. The system must be

filled before operating the circulator. The bearings are water lubricated and should not be allowed to operate dry. Filling the system

will result in immediate lubrication of the bearings. It is always good practice to flush a new system of foreign matter before starting

the circulator.

Always install with motor in horizontal orientation.

Position electrical junction box at 9 o’clock for best

viewing orientation. Pump casing may be rotated to

change flow direction. Locate the arrow on the cas-

ing body to determine flow direction.

CAUTION: To reduce the possibility of noise transmission, be sure to add vibration dampeners to piping when mounting circulator to wall

or floor joists.

ATTENTION: Pour réduire la possibilité de transmission de bruit, veillez à ajouter des amortisseurs de vibration à la tuyauterie lors du

montage du circulateur sur des chevêtres de mur ou de plancher.

WARNING: Risk of electric shock. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, ground-

ing-type receptacle. Follow all local electrical and plumbing codes.

AVERTISSEMENT: Risque de choc électrique. Pour réduire le risque de choc électrique, veillez à ce qu'elle soit raccordée uniquement à

un réceptacle de type mise à la terre proprement mis à la terre. Respectez tous les codes de plomberie et électriques locaux.

Across a Series

Loop System Using

Zone Valves

Across Multi-Zone

Radiant Manifolds

with Loop Actuators

iSeries-R

MM MM MM MM

Outdoor

Sensor

Boiler

Sensor

Typical Variable Speed Applications:

• Zone Valves

• Panel Radiation with

Thermostatic Valves

• Radiant Loops with

Actuators

- Varies speed to

maintain proportional

or constant pressure

differential (∆P)

WARNING: Disconnect power when servicing. CAUTION: Use flexible conduit only. Not for use with rigid conduit.

CAUTION: Do not use flat rubber gaskets. Only use O-ring gaskets provided or leaks may result. Warranty will be void.

WARNING: SERVICING OF DOUBLE-INSULATED APPLIANCES. A double-insulated appliance is marked with one or more of the following:

The words “DOUBLE INSULATION” or “DOUBLE INSULATED” or the double insulation symbol (square within a square). In a double-insu-

lated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added. Servicing a double-insulated appliance requires extreme care and knowledge of

the system, and should be done by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to

the parts they replace.

Integral Flow Check (IFC

) option - An IFC

is included in the carton. If required, press IFC into machined discharge port with plunger

and o-ring facing in, until it snaps into place. Before installing, press IFC plunger to be sure it moves freely. See diagram above.

Figure 4:

Figure 5:

CASING ROTATION

To rotate the pump casing, remove the 4 motor screws. When rotating pump casing position, DO NOT detach

motor housing from the casing. Damage to the casing O-ring and leakage may result. Simply spin casing to the

proper flow direction desired as shown in Figure 4 and Figure 5. Reattach the 4 screws (

⁄

" allens wrench

required). Be sure motor is positioned correctly and is seated evenly to prevent leakage or damage to O-ring.

Tighten motor screws evenly to 25-38 in-lbs torque.

Spin

casing

change

flow

direction.

Spin casing

to change

flow direction.

Figure 6: Do not detach motor frame from pump

casing. Simply spin casing to the

proper flow direction.

5. Start the circulator: When purging the system, it is recommended to run the circulator at full speed long enough to remove remaining

air from the bearing chamber. This is especially important when installing the circulator in the off-season.

Full Speed Operation:

To run the pump at full speed during the fast fill, start-up and purge process, rotate dial to MAX speed setting. To return to the normal

operating mode, turn dial to desired fixed speed, constant pressure, or proportional pressure setting.

6. Programming your VR1816 circulator:

Note: The VR1816 is factory-programmed for maximum speed operating mode. If this is your desired operating mode, no pro-

gramming changes are required.

To change operating mode and settings:

Modify the performance of the circulator as needed by rotating the dial using a flat screwdriver. A blue, orange or green LED will

illuminate when the circulator is powered on. The LED will flash each time mode is changed. See diagrams below to determine best

mode of operation for the system.The selection of the right functioning curve depends on the characteristics of the heating sys-

tem and the actual heat demand.

CAUTION: Never run the circulator dry or permanent damage may result.

ATTENTION: Ne laissez jamais le circulateur tourner à sec, des dommages permanents peuvent en résulter.

The VR1816 has 3 Operating Modes:

• Fixed Speed ( ) - Infinitely adjustable settings (MIN-MAX).

• Constant Pressure ( ) - Varies speed to maintain a constant pressure differential.

• Proportional Pressure ( ) - Varies speed to maintain a proportional/variable pressure differential.

Min

Max

Q(gpm)

012 3 4567 8 910111213141516

H (ft)

Q (l/s)

0.0 0.2 0.4 0.6 0.8 1.0 1.2

H (m)

Q (m

/h)

43210

0015 – Hi

008

0015 – Med

007

0015 – Low

006

003

Flow

Head in Feet

Fixed speed mode ( ) allows the installer to fine tune the circulator flow rate to precisely match design load conditions.

It is infinitely variable between MIN/MAX settings. See chart above for equivalent 00 model at each variable speed setting.

Shaded area represents full

operating range.

Blue

LED

min -

max

4. Wiring the circulator: Disconnect AC power supply. Remove terminal

box cover. Attach a wiring connector into knockout hole. Use flexible con-

duit only. Connect Line/Hot power to the black lead, Neutral to the white

lead. See wiring diagram.

Note: If pigtail leads provided are not used, be sure to trim field wire to a strip

length of .25" (+/- .025") to prevent exposed wire causing a short at the ter-

minal plug. Connect line and neutral to green terminal plug as shown in dia-

gram. Depress the spring tab with a small screwdriver to insert wire into plug.

Release tabs to complete connection. The VR1816 is a double insulated cir-

culator, no grounding wire is necessary. Replace terminal box cover.

NEUTRAL

WIRING DIAGRAM

No ground wire is required.

Green Terminal Plug

Spring Tabs

WIRE NUT

WHITE

BLACK

LINE

FIXED SPEED MODE ( )

Infinitely Adjustable (MIN-MAX)

VR1816 PERFORMANCE CURVES

CAUTION: Do not attempt to remove LED panel from circulator. Serious damage to circulator electronics may result.

ATTENTION: N'essayez pas de retirer le panneau de LED du circulateur. Des dommages sérieux à l'électronique du circulateur peuvent

en résulter.

Q(gpm)

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

H (ft)

Q (l/s)

0.0 0.2 0.4 0.6 0.8 1.0 1.2

H (m)

Q (m

/h)

43210

008

0015 – Med

007

0015 – Low

006

Flow

Head in Feet

In Constant pressure mode ( ), the circulator maintains a constant pressure differential (∆p-c) in the system as heating load

increases or decreases. Selection options are 5, 10, or 15 feet of head maximum constant pressure. See chart above for equiv-

alent 00 model at each setting.

Low

Med

High

Q(gpm)

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

H (ft)

Q (l/s)

0.0 0.2 0.4 0.6 0.8 1.0 1.2

H (m)

Q (m

/h)

43210

Flow

Head in Feet

In Proportional pressure mode ( ), the circulator maintains a proportional pressure differential (∆p-v) as heating load increases

or decreases. Flow will change in relationship to the change in pressure differential. Selection options are Low, Medium, or High.

If unsure on proper setting, select Medium

and adjust as needed.

Orange

LED

Green

LED

VR1816 PERFORMANCE CURVES

PROPORTIONAL PRESSURE MODE ( )

Variable Speed

CONSTANT PRESSURE MODE ( )

Variable Speed

7. Troubleshooting the error codes: Listed below are potential diagnostic error codes which will appear on the LED display in case

of a malfunction.

FAULTS

CONTROL

PANEL

CAUSESREMEDIES

The circulator is

noisy

LED on

Suction pressure is

insufficient - cavitation

Increase the system suction

pressure within the

permissible range.

LED on

Presence of foreign bodies

in the impeller

Disassemble the motor and

clean the impeller.

Loud noises of

water circulation

Flashing white

LED

Air in the system

Vent the system. Repeat

fill and purge steps.

LED on The flow is too high Reduce the pump speed.

Circulator is not

running although

the electrical

power supply is

switched on

LED off

Lack of power supply

Verify voltage value of the

electric plant.

Verify the connection of the

motor.

One fuse in the installation

is blown

Verify the fuses of the plant.

The circulator is defective Replace the pump.

Overheating

Let the pump cool down for

some minutes. Then try to re-

start it. Verify that the water

and ambient temperature are

within the indicated

temperature ranges.

LED red The rotor is blocked

Disassemble the motor and

clean the impeller. See

unblocking procedure below.

Insufficient supply voltage

Verify that the power supply

matches the data on the name

plate.

Building does not

get warm.

LED on

The circulator

performance is too low

Increase the suction head.

Increase speed or ∆P setting.

Unblocking Procedure:

A red light in the LED indicates the circulator rotor is blocked or sticking. Turn the selector to the position MAX, disconnect and

connect power supply to start the automatic release process. The circulator makes 100 attempts to restart (process lasts approx-

imately 15 minutes). Every restart is signalled by a short flash of white LED light. If the blocking is not removed through the auto-

matic release process after 100 attempts to restart, the circulator goes into standby and the LED remains solid red. Perform the

manual unblocking steps described below.

1. Disconnect power supply - the warning light switches off.

2. Close both isolating valves and allow cooling. If there are no shut-off devices, drain the system so that the fluid level is

beneath that of the circulator.

3. Loosen 4 motor bolts. Remove motor from casing. Carefully pull the rotor/impeller from the motor.

4. Remove impurities and deposits from the impeller and casing.

5. Reinsert the rotor/impeller into the motor.

6. Set the dial to the MAX position.

7. Connect power supply. Check for impeller rotation.

8. If the circulator still doesn’t run it will need to be replaced.

LIMITED WARRANTY STATEMENT

Taco, Inc. will repair or replace without charge (at

the company’s option) any Taco High Efficiency

circulator or circulator part which is proven defec-

tive under normal use within three (3) years from

the date of manufacture.

In order to obtain service under this warranty, it

is the responsibility of the purchaser to promptly

notify the local Taco stocking distributor or Taco

in writing and promptly deliver the subject product

or part, delivery prepaid, to the stocking distribu-

tor. For assistance on warranty returns, the pur-

chaser may either contact the local Taco stock-

ing distributor or Taco. If the subject product or

part contains no defect as covered in this war-

ranty, the purchaser will be billed for parts and

labor charges in effect at time of factory exami-

nation and repair.

Any Taco product or part not installed or operated

in conformity with Taco instructions or which has

been subject to misuse, misapplication, the addi-

tion of petroleum-based fluids or certain chemi-

cal additives to the systems, or other abuse, will

not be covered by this warranty.

If in doubt as to whether a particular substance

is suitable for use with a Taco product or part, or

for any application restrictions, consult the

applicable Taco instruction sheets or contact

Taco at (401-942-8000).

Taco reserves the right to provide replacement

products and parts which are substantially similar

in design and functionally equivalent to the

defective product or part. Taco reserves the right

to make changes in details of design, construc-

tion, or arrangement of materials of its products

without notification.

TACO OFFERS THIS WARRANTY IN LIEU OF

ALL OTHER EXPRESS WARRANTIES. ANY

WARRANTY IMPLIED BY LAW INCLUDING

WARRANTIES OF MERCHANTABILITY OR

FITNESS IS IN EFFECT ONLY FOR THE DURA-

TION OF THE EXPRESS WARRANTY SET

FORTH IN THE FIRST PARAGRAPH ABOVE.

THE ABOVE WARRANTIES ARE IN LIEU OF

ALL OTHER WARRANTIES, EXPRESS OR

STATUTORY, OR ANY OTHER WARRANTY

OBLIGATION ON THE PART OF TACO.

TACO WILL NOT BE LIABLE FOR ANY SPE-

CIAL, INCIDENTAL, INDIRECT OR CONSE-

QUENTIAL DAMAGES RESULTING FROM THE

USE OF ITS PRODUCTS OR ANY INCIDENTAL

COSTS OF REMOVING OR REPLACING

DEFECTIVE PRODUCTS.

This warranty gives the purchaser specific rights,

and the purchaser may have other rights which

vary from state to state. Some states do not

allow limitations on how long an implied warranty

lasts or on the exclusion of incidental or conse-

quential damages, so these limitations or exclu-

sions may not apply to you.

SPEED TACO GRUNDFOS WILO B & G/XYLEM ARMSTRONG

Minimum

003

006

Alpha 15-55 (Low)

Eco-Vario (Low)

Compass (1)

Medium

007

008

0015 (Low)

0015 (Med)

UP-15-42

UPS-15-58 (Low)

UPS-15-58 (Med)

Alpha 15-55 (Med)

Star S-21 (1)

Star S-21 (2)

NRF-25 (1)

NRF-25 (2)

Eco-Vario (Med)

Astro 230 (1)

Astro 230 (2)

Compass (2)

Maximum 0015 (Hi)

UPS-15-58 (Hi)

Alpha 15-55 (Hi)

Star S-21 (3)

NRF-25 (3)

Eco-Vario (Hi)

Astro 230 (3)

Compass (3)

VR1816 Pump Cross Reference (Fixed Speed Mode):

TACO GRUNDFOS WILO B & G/XYLEM ARMSTRONG

VR1816 Alpha 15-55 Stratos Eco Eco-Auto Compass 20-20

VR1816 Pump Cross Reference (Variable Speed Mode):

A Taco Family Company

2017

198-213 RP Casing O-ring

198-214 RP Wiring plug connector (green)

198-215 RP Terminal box cover (black)

198-217 RP Terminal box cover screws (5 per bag)

0010-025 RP Integral Flow Check (IFC

)

007-007 RP Flange gasket set

Replacement Parts List

Taco Comfort Solutions VR1816HY2FC2A00 Mode d'emploi

Marque: Taco Comfort Solutions

Modèle: VR1816HY2FC2A00

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Taco Comfort Solutions VR1816HY2FC2A00 Operating instructions

Taco Comfort Solutions VR1816HY2FC2A00 Mode d'emploi

Taco Comfort Solutions VR1816HY2FC2A00 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents