Genesis EP -310/320 Le manuel du propriétaire

Catégorie
Barbecues
Taper
Le manuel du propriétaire

Ce manuel convient également à

E/S-310/320, EP -310/320
#89478
YOU MUST READ THiS OWNER'S GUIDE
BEFORE OPERATING YOUR GAS GRILL
Z_ DANGER
if you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid.
4. if odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
z_ WARNING:
1. Do not store or use gasoline or other
flammable liquids or vapors in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
Z_ WARNING: Follow all leak-check
procedures carefully in this manual prior
to barbecue operation. Do this even if the
barbecue was dealer-assembled.
NOTICE TO iNSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
THIS GAS APPLIANCE iS DESIGNED FOR
OUTDOOR USE ONLY.
z_ WARNING: Do not try to light this
appliance without reading the "Lighting
instructions" section of this manual.
MEMBER
89478 08/22/08 LP
US ENGLISH
DANGER
Failure to follow the Dangers, Warnings and Cautions contained in this Owner's Manual may result in serious bodily injury or
death, or in a fire or an explosion causing damage to property.
WARNINGS
z_ Do not store a spare or disconnected liquid propane cylinder under or near this barbecue.
z_ Improper assembly may be dangerous. Please follow the assembly instructions carefully.
z_ After a period of storage, and/or nonuse, the Weber ®gas barbecue should be checked for gas leaks and burner obstructions
before use. See instructions in this manual for correct procedures.
z_ Do not operate the Weber _ gas barbecue if there is a gas leak present.
z_ Do not use a flame to check for gas leaks.
z_ Combustible materials should never be within 24 inches (61 cm) of the back or sides of your Weber _ gas barbecue.
z_ Do not put a barbecue cover or anything flammable on, or in the storage area under the barbecue.
z_ Your Weber _ gas barbecue should never be used by children. Accessible parts of the barbecue may be very hot. Keep young
children away while it is in use.
z_ You should exercise reasonable care when operating your Weber ®gas barbecue. It will be hot during cooking or cleaning and
should never be left unattended, or moved while in operation.
z_ Should the burners go out while in operation, turn all gas valves off. Open the lid and wait five minutes before attempting to
relight, using the lighting instructions.
z_ Do not use charcoal or lava rock in your Weber ®gas barbecue.
z_ Never lean over open grill or place hands or fingers on the front edge of the cooking box.
z_ Should a grease fire occur, turn off all burners and leave lid closed until fire is out.
z_ Do not enlarge valve orifices or burner ports when cleaning the valves or burners.
z_ The Weber ®gas barbecue should be thoroughly cleaned on a regular basis.
Z_ Liquid propane gas is not natural gas. The conversion or attempted use of natural gas in a liquid propane unit or liquid propane
gas in a natural gas unit is dangerous and will void your warranty.
Z_ Do not attempt to disconnect any gas fitting while your barbecue is in operation.
Z_ Use heat-resistant barbecue mitts or gloves when operating barbecue.
Z_ Keep any electrical supply cord and the fuel supply hose away from any heated surfaces.
Z_ Combustion byproducts produced when using this product contain chemicals known to the state of California to cause cancer,
birth defects, or other reproductive harm.
Z_ Do not use this barbecue unless all parts are in place. The unit must be properly assembled according to the assembly
instructions.
Z_ Do not build this model of grill in any built-in or slide in construction, ignoring this Warning could cause a fire or an explosion
that can damage property and cause serious bodily injury or death.
z_ Proposition 65 Warning: Handling the brass material on this product exposes you to lead, a chemical known to the state of
California to cause cancer, birth defects or other reproductive harm.
(Wash hands after handfing this product.)
LIQUID PROPANE GAS UNITS ONLY:
z_ Use the pressure regulator and hose assembly that is supplied with your Weber _ gas barbecue.
z_ Do not attempt to disconnect the gas regulator and hose assembly or any gas fitting while your barbecue is in operation.
Z_ A dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid propane supplier. Do not
use a liquid propane cylinder with a damaged valve.
Z_ Although your liquid propane cylinder may appear to be empty, gas may still be present, and the cylinder should be
transported and stored accordingly.
z_ If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder:
1. Move away from liquid propane cylinder.
2. Do not attempt to correct the problem yourself.
3. Call your fire department.
Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber _
gas grill that it will be free of defects in material and workmanship from the date of purchase as follows:
Aluminum castings 25-years (2 years on paint: excludes fading)
Stainless sleel Shroud, 25-years:
Porcelain-enameled shroud, 25-years
Cookbox Assembly 10-years (2 year on paint excludes fading)
Stainless sleel burners tubes, f0-years
Stainless steel cooking grates, 5-years no rusl through or burn through
Stainless steel F]avorizer bars, 5-years no rust through or burn through
Porcelain-enameled cast-iron
cooking grates, 5-year no rust through or burn through
Porcelain-enameled
cooking grates, 3-years no rust through or burn through
Porcelain-enameled
Flavodzer bars, 2-years no rust through or burn through
Infrared Rotisserie Burner, 2-years
AH remaining parts, 2-years
When assembled and operated in accordance with the printed instructions accompanying it.
Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN
YOUR SALES SLIP OR INVOICE.
This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under
normal use and service and which on examination shall indicate, to Weber's satisfaction, they are
defective. Before returning any parts, contact the Customer Service Representative in your area
using the contact information on our website. If Weber confirms the defect and approves the claim,
Weber will elect to replace such parts without charge. If you are required to return defective parts,
transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage
prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse,
misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or
service, or failure to perform normal and routine maintenance, including but not limited to damage
caused by insects within the burner tubes, as set out in this owner's manual.
Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes
or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not
covered by this Limited Warranty.
There are no other express warrants except as set forth herein and any applicable implied warranties
of merchantability and fitness are limited in duration to the period of coverage of this express written
Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this
limitation may not apply to you.
Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the
exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not
apply to you.
Weber does not authorize any person or company to assume for it any other obligation or liability in
connection with the sale, installation, use, removal, return, or replacement of its equipment; and no
such representations are binding on Weber.
This Warranty applies only to products sold at retail.
WEBER-STEPHEN PRODUCTS CO.
Customer Service Center
1890 RoseHe Road, Suite 308
Schaumburg, IL 60195
USA
For replacement parts call:
1-800-446-1071
www.weber.com ®
Weber-Stephen Products Co., (Weber) mediante la presente le garantiza al COMPRADOR ORIGINAL
de esta barbacoa de gas Weber e que la misma estara libra de defectos en cuanto a materiales y
fabricacion a partir de la fecha de compra segun Io siguiente:
Piezas coladas de aluminio
Cubierta de acero inoxidable,
Cubierta porcelanizada,
Camara para asar
Tubes de acero inoxidable
de los quemadores.
Parrilas de cocci6n de
acero inoxidable.
Barras Flavorizer de
acero inoxidable,
Parrillas de cocci6n de hierro
colado porcelanizado,
Parrillas de cocci6n porcenlanizadas.
Barras Flavorizer porcelanizadas.
Qumeador infrarrojo del
asador giratorio.
Todas la demas partes.
25-a1_os (2 ai_os para la pintura excluyendo la decoloraci6n)
25-a1_os
25-aiios
10-ai_os (2 ai_os para la pintura excluyendo la decoloraci6n)
10-ai_os
5-ai_os sin pertoraciSn per fuego u oxidaciSn
5-ai_os sin pertoraciSn per fuego u oxidaciSn
5-abos sin pertoraciSn per fuego u oxidaciSn
3-abos sin pertoraciSn per fuego u oxidaciSn
2-ai_os sin pertoraciSn per fuego u oxidaciSn
2-abos
2-ai_os
cuando se ensambla y opera de acuerdo alas instrucciones impresas que la acompa_an.
Weber pudiese requerir prueba razonable de la fecha de compra. PeR LO TANTO, DEBER#,
GUARDAR SU RECIBO O FACTURA DE VENTA.
Esta garantia limitada ester limitada a la reparacion o reemplazo de plazas que resultasen defectuosas
bale use y servicio normal y las cuales al examinarse indiquen, a plena satisfaccion de Weber, que
efectivamente son piezas defectuosas. Antes de devolver cualquier parte, contacte al Representante
de Atencion al Cliente en su _trea, cuya informacion de contacto la encontrar4, en nuestro sitio web. Si
Weber confirma el defecto y aprueba el reclamo, esta elegir4, reparar o reemplazar tal pieza sin cargo
alguno. Si usted tiene que retornarnos las partes defectuosas, los gastos de transporte deben ser
prepagados. Weber retornara las partes al comprador con transporte o franqueo prepagado.
Esta Garantia Limitada no cubre ninguna falla o problema de operacion a causa de accidentes,
abuse, mal use, alteracion, use en aplicaciones indebidas, vandalismo, instalacion inapropiada o
mantenimiento o servicio inapropiados, o per no Ilevar a cabo el mantenimiento normal y rutinario,
entre los que se incluyen, pete sin limitacion, los dafios causados per insectos dentro de los tubes
quemadores, segLin se detalla en este manual del propietario.
Esta Garantia Limitada no cubre el deterioro o da_os a causa de condiciones de tiempo inclemente
tales come granizo, huracanes, terremotos o tornados ni tampoco la decoloracion per exposicion a
sustancias quimicas bien sea per contacto directo o per que las mismas contenidas en la atmosfera.
No existe ninguna otra garantia expresa que no sean las las ac_t indicadas y cualesquier garantias
implicitas de comerciabilidad y aptitud de use est_tn limitadas en duracion al tiempo de cobertura de
esta expresa Garantia Limitada per escrito. Algunas regiones no permiten limitacion alguna en el
tiempo que una garantia implicita pueda durar, per Io que esta limitacion pudiera no aplicarle a usted.
Weber no se hace responsable de cualesquier da_os especiales, indirectos o emergentes. Algunas
regiones no permiten la exclusion o limitacion de dafios incidentales o emergentes, per Io que esta
limitacion o exclusion pudieran no aplicarle a usted.
Weber no autoriza a persona o empresa alguna a asumir en su nombre ninguna obligacion o
responsabilidad en relacion con la venta, instalacion, use, retire, devolucion o reemplazo de sus
equipos, y ninguna tal representacion set4. vinculante para Weber.
Esta Garantia aplica solo a aquellos productos vendidos al per menor.
WEBER-STEPHEN PRODUCTS CO.
CustomerService Center
1890 RoseHe Road, Suite308
Schaumburg, lL 60195
USA
Para partes de repuesto Ilame a:
1-800-446-1071
www.weber.com ®
Para compras hechas en MExico
WEBER-STEPHEN PRODUCTS S.A. de C.V.
MatceJJa No. 338,
Colonia Americana
44160 M_×ico, C.P.
MExico
Para partes de repuesto Ilame a:
(52} (33) 3615-0736
www.weber.com ®
Weber-Stephen Products Co. (Weber) garantit par le present document t_I'ACHETEUR D'ORIGINE de
ce grill a gaz Weber _ que celui-ci ne comportera aucun defaut de piece ni de main d'oeuvre a compter
de la date d'achat comme suit :
Fonte d'aluminium
Structure en acier inoxydable.
Structure emaillee,
Cuve,
Tubes du brQ]eur en acier inoxydab]e,
Grilles de cuisson en acier inoxydab]e,
Barres F]avodzer en acier inoxydab]e,
Grilles de cuisson en fonte far email]Oe,
Gdl]es de cuisson 6rnai]lees,
Barres Flavorizer 6rnaH]ees,
BrOleur de la rOtissoire & infrarouge,
Toutes les autres pieces,
25 ans (2 ans pour lapeinture & rexception de route d@coloration)
25 ans
25 ans
10 ans (2 ans pour la peinture a I'exception de route d@coloration)
10 ans
5 ans sans trou provoque par la rouille ou par une brQlure
5 ans sans trou provoque par la rouille ou par une brQlure
5 ans sans trou provoque par la rouille ou par une brQlure
3 ans sans trou provoque par la rouille ou par une brQlure
2 ans sans trou provoque par la rouille ou par une brt31ure
2 ans
2 ans
_tcondition qu'il ait ete assemble et utilise conformement aux instructions imprimees qui
I'accompagnent.
Weber peut exiger une preuve raisennable de vetre date d'achat. VOUS DEVRIEZ DONC
CONSERVER VOTRE TICKET DE CAISSE OU VOTRE FACTURE.
La presente Garantie limitee est limitee a la reparation ou au remplacement des pieces qui s'averent
defectueuses dans le cadre d'une utilisation normale et d'un entretien normal et dent I'examen indique,
_tla satisfaction de Weber, qu'elles sent defectueuses. Avant de retourner toute piece, veuillez
entrer en contact avec le Representant du Service clientele le plus proche gr&ce aux coordonnees
_tvetre disposition sur notre site Internet. Si Weber confirme le defaut et approuve la demande,
Weber choisira de remplacer ces pieces sans frais. S'il vous est demande de retourner les pieces
defectueuses, les frais de transport devrent ¢tre prepayes. Weber retournera les pieces _tI'acheteur,
france de port.
La presente Garantie limitee ne couvre pas toute defaillance ou difficulte d'utilisation provequee par un
accident, une utilisation abusive, une mauvaise utilisatien, une alteration, une mauvaise application, un
acte de vandalisme, une installation incorrecte eu une maintenance ou un entretien incorrects, ou le
defaut d'entretien normal et regulier, y compris mais pas seulement les demmages prevoques par des
insectes _t I'interieur des tubes du brQleur, tel que decrit dans le present mode d'emploi.
Toute deterioration eu tout dommage resultant de conditions meteerelogiques graves comme de la
gr¢le, des ouragans, des seismes ou des tornades, teute deceleration resultant d'une exposition a des
agents chimiques directement eu dans I'atmosphere, n'est pas couverte dans le cadre de la presente
Garantie limitee.
II n'existe aucune autre garantie expresse hormis celles expesees dans le present document et teute
garantie de commercialisation et de ben etat induite est limitee en duree a la periode de couverture de
la presente Garantie limitee ecrite expresse. Certaines regions n'auterisent pas de limitation de duree
de la garantie induite ; il est denc posible que cette limitation ne s'applique pas _tveus.
Weber ne peut ¢tre tenu pour responsable de tout demmage particulier, induit eu se produisant par
vole de consequence. Certaines regions n'auterisent pas I'exclusien ou la limitation des dommages
indirects ou se produisant par vole de consequence ; il est denc possible que cette limitation ou
exclusion ne s'applique pas _tveus.
Weber n'autorise aucune personne eu societe a presumer en son nem de toute autre obligation
eu responsabilite en relation avec la vente, I'installation, I'utilisation, le retrait, le reteur eu le
remplacement de ses equipements ; et aucune de ces representations ne lie Weber.
La presente Garantie s'applique uniquement aux produits vendus au detail.
WEBER-STEPHEN PRODUCTS CO.
Product Registration
P.O. Box 40530
Burlington, ON L7P 4Wl
Pour des pieces de rechange, appelez le :
1-800-265-2150
www.weber.com ®
VISION I_CLATI_E, DIAGRAHA DE DESPIECE
1
2
3
4
5
6
7
G
Genesis_310 LP US 09
©
©
23
24
25
26
_27
_28
29
10
11
30
31
32
33
34
35
12
13
14
15
16
17
18
19
20
21
22
36
37
38
39
40
41
45
46
47
LISTA DEL DIAGRAMA DE DESPIECE, LISTE DE LA ViSiON I_CLATI_E
1, Shroud Hardware 18, Catch Pan 35, Back Panel
Accesorios de la cubierta Plato recolector Panel trasero
Structure de protection Egouttoir Panneau arriere
2, Thermometer 19, Front Panel 36, Tank Scale
Term6metro Panel frontal Bb,scula del tanque
Thermometre Panneau avant Plateau de la bouteille
3, Thermometer Bezel 20, Left Door 37. Manifold
Moldura decorativa del term6metro Puerta izquierda Multiple
Plaque indicatrice du thermometre Porte gauche Collecteur
4. Shroud 21. Right Door 38. Hose/Regulator
Cubierta Puerta derecha Manguera / Regulador
T61ede protection Porte droite Tuyau/Regulateur
5, Handle 22. Door Handle 39. Right Frame Panel
Asa Asa de la puerta Panel derecho del basfidor
Poignee Poignee de porte Panneau du cadre droit
6, Warming Rack 23, Control Knob 40, Tank Glides
Rejilla de calentamiento Perilla de control DeslJzaderas del tanque
Grille de rechauffage Bouton de commando Glissieres de la bouteille
7. Left SideTable 24, Bezel #3 41. DripTray
Mesa lateral Jzquierda Moldura decorativa #3 Bandeja de goteo
Tablette lat@ale gauche Plaque indicatrice N° 3 Egouttoir
8, Cooking Grates 25, Bezel #2
Parrillas de coccJ6n Moldura decorativa #2
Grilles de cuisson Plaque indicatrice N° 2
42, RightTrim Piece
Pieza de guarnici6n derecha
Piece de garniture droite
9, Crossover®Tube 26, Bezel #1 43, Matchstick Holder
Tubo Crossover _ Moldura decorativa #1 Portacerillos
Tuyau Crossover _ Plaque indicatrice N° 1 Porte-allumette
10, Cookbox 27. Igniter Button
Caja de coccidn Bot6n de encendido
Boitier de cuisson Bouton d'allumage
44. Right Front Trim Piece
Pieza de guarnici6n frontal derecha
Piece de garniture avant droite
11. Left Frame Panel 28, Igniter Module 45, Caster
Panel Jzquierdo del bastidor M6dulo de encendJdo Rueda giratoria
Panneau du cadre gauche Module d'allumage Roulette
12, Rear Frame Support 29, Right SideTable 46. Bottom Panel
Soporte posterior del bastidor Mesa lateral derecha Panel inferior
Support arriere du cadre Tablette laterale droite Panneau inferieur
13, Front Frame Support 30, Flavorizer _ Bar 47. Locking Caster
Soporte delantero del bastidor Barra Flavorizer _ Rueda giratoria con bloqueo
Support avant du cadre Barre Flavorizer :e Roulette autobloquante
14. LeftTrim Piece 31, Rear BurnerTube
PJeza de guarnici6n izquierda Tubo quemador posterior
Piece de garniture gauche Tube du brQleur arriere
15, Left Front Trim Piece
PJeza de guarnici6n frontal izquierda
Piece de garniture avant gauche
32, Middle BurnerTube
Tubo quemador del medio
Tube du brQleur du milieu
16. Catch Pan Holder 33. Front BurnerTube
Soporte del plato recolector Tubo quemador frontal
Support d'egouttoir Tube du brQleur avant
17. Disposable Drip Pan
Bandeja de goteo desechable
Egouttoi r jetable
34, Igniter Electrode
Electrodo del encendedor
Igniter Electrode
ViSiON ECLATEE, DIAGRAiVlA DE DESPIECE
1
2
3
4
5
6
7
Genesis_320 LP US 09
©
©
25
26
27
28
29
30
31
10
11
12
13
32
33
34
35
36
37
14
15
16
17
18
19
20
21
22
23
24
,Q
38
39
40
41
42
43
44
45
46
47
48
49
5O
LISTA DEL DIAGRAIVlA DE DESPIECE, LISTE DE LA ViSiON leCLATleE
1, Shroud Hardware
Accesorios de la cubierta
Structure de protection
18, Catch Pan Holder
Soporte del plato recolector
Support d'egouttoir
35, Front BurnerTube
Tubo quemador frontal
Tube du brQleur avant
2, Thermometer 19, Disposable Drip Pan 36, igniter Electrode
Term6metro Bandeja de goteo desechable Electrodo del encendedor
Thermometre Egouttoir jetable Igniter Eectrode
3, Thermometer Bezel 20, Catch Pan 37, Back Panel
Moldura decorativa del term6metro Plato recolector Panel trasero
Plaque indicatrice du thermometre Egouttoir Panneau arriere
4, Shroud 21, Front Panel 38, Tank Scale
Cubierta Panel frontal Bb,scula del tanque
T61ede protection Panneau avant Plateau de la bouteille
5, Handle 22. Left Door 39. Manifold
Asa Puerta izquierda Multiple
Poignee Porte gauche Collecteur
6, Warming Rack 23. Right Door 40, Hose/Regulator
Rejilla de calentamiento Puerta derecha Manguera / Regulador
Grille de rechauffage Porte droite Tuyau/Regulateur
7. Side Burner Table
Mesa del quemador lateral
Tablette du brQleur lat@al
24, Door Handle 41. Right Frame Panel
Asa de la puerta Panel derecho del bastidor
Poignee de porte Panneau du cadre droit
8, Side Burner Lid 25, Control Knob 42, Manifold Hose
Tapa del quemador lateral Perilla de control Manguera del multiple
Couvercle du brQleur lat@al Bouton de commando Tuyau du collecteur
9, Cooking Grates 26, Bezel #3 43, Tank Glides
Parrillas de cocci6n Moldura decorativa #3 Deslizaderas del tanque
Grilles de cuisson Plaque indicatrice N° 3 Glissieres de la bouteille
10, Side Burner 27. Bezel #2 44. DripTray
Quemador lateral Moldura decorativa #2 Bandeja de goteo
BrQleur lat@al Plaque indicatrice N° 2 Egouttoir
11. CrossoverTube 28, Bezel #1
Tubo Crossover Moldura decorativa #1
Tuyau Crossover Plaque indicatrice N° 1
45, RightTrim Piece
Pieza de guarnici6n derecha
Piece de garniture droite
12, Cookbox 29, Igniter Button 46. MatehstickHolder
Caja de cocci6n Bot6n de encendido Portacerillos
Boitier de cuisson Bouton d'allumage Porte-allumette
13, Left Frame Panel
Panel izquierdo del bastidor
Panneau du cadre gauche
30, igniter Module
M6dulo de encendido
Module d'allumage
47. Right Front Trim Piece
PJeza de guarnici6n frontal derecha
Piece de garniture avant droite
14. Rear Frame Support 31, Right SideTable 48, Caster
Soporte posterior del bastidor Mesa lateral derecha Rueda giratoria
Support arriere du cadre Tablette laterale droite Roulette
15, Front Frame Support 32, FJavorizer ®Bar 49, Bottom Panel
Soporte delantero del bastidor Barra Flavorizer _ Panel inferior
Support avant du cadre Barre Flavorizer :e Panneau inferieur
16. LeftTrim Piece
Pieza de guarnicidn izquierda
Piece de garniture gauche
33. Rear BurnerTube
Tubo quemador posterior
Tube du brQleur arriere
50, Locking Caster
Rueda giratoria con bloqueo
Roulette autobloquante
17. Left FrontTrim Piece
PJeza de guarnici6n frontal izquierda
Piece de garniture avant gauche
34. Middle Burner Tube
Tubo quemador del medio
Tube du brQleur du milieu
Your Webei _ gas barbecue is a portable outdoor cooking appliance. With the Weber ¢
gas barbecue you can grill, barbecue, roast and bake with results that are difficult to
duplicate with indoor kitchen appliances. The closed lid and Flavorizer ¢ Bars produce
that "outdoor" flavor in the food.
The Weber ¢ gas barbecue is portable so you can easily change its location in your yard
or on your patio. Portability means you can take your Weber _ gas barbecue with, if you
move.
Liquid Propane (LP) gas supply is easy to use and gives you more cooking control than
charcoal fuel.
o These instructions will give you the minimum requirements for assembling your
Weber _ gas barbecue. Please read the instructions carefully before using your
Weber ¢ gas barbecue. Improper assembly can be dangerous.
Not for use by children.
If there are local codes that apply to portable gas grills, you will have to conform to
them. Installation must conform with local codes or, in the absence of local codes,
with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and
Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code,
B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and
CSA Z240 RV Series, Recreational Vehicle Code, as applicable.
The pressure regulator supplied with the Weber _ gas barbecue must be used.
This regulator is set for 11 inches of water column (pressure).
This Weber s gas barbecue is designed for use with liquid propane (LP) gas only.
Do not use with natural (piped in city) gas. The valves, orifices, hose and regulator
are for LP gas only.
Do not use with charcoal fuel.
Check that the area under the control panel and the bottom tray are free from
debris that might obstruct the flow of combustion or ventilation air.
The areas around the LP cylinder must be free and clear from debris.
Replacement pressure regulators and hose assemblies must be those specified
by Weber-Stephen Products Co.
FOR INSTALLATION IN CANADA
These instructions, while generally acceptable, do not necessarily comply with the
Canadian Installation codes, particularly with piping above and below ground. In
Canada the installation of this appliance must comply with local codes and/or Standard
CSA-B149.2 (Propane Storage and Handling Code).
OPERATING
WARNING: Only use this barbecue outdoors in a well-
ventilated area. Do not use in a garage, building, breezeway
or any other enclosed area.
WARNING: Keep ventilation openings for cylinder enclosure
free and clear from debris.
z_ WARNING: Your Weber _ gas barbecue shall not be used
under overhead combustible construction.
z_ WARNING: Your Weber _ gas barbecue is not intended to be
installed in or on recreational vehicles and/or boats.
WARNING: Do not use the barbecue within 24 inches of
combustible materiaJs to the back or sides of the grill.
WARNING: The entire cooking box gets hot when in use. Do
not leave unattended.
WARNING: Keep any electrical supply cord and the fuel
suppJy hose away from any heated surface.
WARNING: Keep the cooking area clear of flammable vapors
and liquids such as gasoline, alcohol, etc., and combustible
materials.
z_ WARNING: Never store an extra (spare) LP cylinder under or
near the Weber _ gas barbecue.
WARNING: The LP cylinder used with your barbecue must
be with a listed OPD (Overfilling Prevention Device) and
a QCCl or Type 1 (CGA810) cylinder connection. The
cylinder connection must be compatible with the barbecue
connection.
STORAGE AND/OR NONUSE
o The gas must be turned off at the liquid propane cylinder when the Weber _ gas
barbecue is not in use.
o When the WebeP gas barbecue is stored indoors, the gas supply must be
DISCONNECTED and the LP cylinder stored outdoors in a well-ventilated space.
o LP cylinder must be stored outdoors in a well -ventilated area out of reach of
children. Disconnected LP cylinder must not be stored in a building, garage or any
other enclosed area.
o When the LP cylinder is not disconnected from the Weber _ gas barbecue, the
appliance and LP tank must be kept outdoors in a well-ventilated space.
o The Weber _ gas barbecue should be checked for gas leaks and any obstructions
in the burner tubes before using. (See Section: "Maintenance/Annual
Maintenance).
o Check that the areas under the control panel and the slide out bottom tray are free
from debris that might obstruct the flow of combustion or ventilation air.
o The Spider/Insect Screens should also be checked for any obstructions.
(See Section: "Maintenance/Annual Maintenance").
COOKING
z_ WARNING: Do not move the Weber _ gas barbecue when
operating or while barbecue is hot.
You can adjust BURNER 1,2, and 3 as desired.The control settings: High (H), Medium
(M), Low (L), or Off (O) are described in your Weber e cookbook.The cookbook uses
these notations to describe the settings of BURNER 1,2, and 3. For example, to sear
steaks, you would set all burners at H (high).Then to complete cooking, you would set
BURNER 1 and BURNER 3 at M (medium). Refer to your Weber _ cookbook for detailed
cooking instructions.
Note: The temperature inside your cooking box for the first few uses, while surfaces are
still very reflective, may be hotter than those shown in your cookbook. Cooking condi-
tions such as wind and weather, may require the adjustment of the burner controls to
obtain the correct cooking temperatures.
Preheating - Your Weber ¢ gas barbecue is an energy-efficient appliance. It operates at
an economical low BTU rate.To preheat: after lighting, close lid and turn all burners to
high (H). Preheating to between 500 ° and 550 ° F (260 ° and 290 ° C) will take 10 to 15
minutes depending on conditions such as air temperature and wind.
Drippings and grease - The Flavorizer ¢ bars are designed to "smoke" the correct
amount of drippings for flavorful cooking. Excess drippings and grease will accumulate in
the catch pan under the slide out bottom tray. Disposable foil drip pans are available that
fit the catch pan.
WARNING: Check the bottom tray for grease build-up before
each use. Remove excess grease to avoid a grease fire in the
slide out bottom tray.
CLEANING
WARNING: Turn your Weber ®gas barbecue off and wait for it
to cool before cleaning.
CAUTION: Do not clean your Flavorizer _ bars or cooking
grates in a self-cleaning oven.
For availability of replacement cooking grates and Fmavorizer ° bars contact the
Customer Service Representative in your area using the contact information on
our website. Log onto www.weber.com ®
Outside surfaces - Use a warm soapy water solution to clean, then rinse with water.
z_ CAUTION: Do not use oven cleaner, abrasive cleansers
(kitchen cleansers), cleaners that contain citrus products, or
abrasive cleaning pads on barbecue or cart surfaces.
Slide out Bottom tray - Remove excess grease, then wash with warm soapy water,
then rinse.
Flavorizer e bars and Cooking grates - Clean with a suitable brass bristle brush. As
needed, remove from grill and wash with warm soapy water, then rinse with water.
Catch pan - Disposable foil trays are available, or you can line the catch pan with
aluminum foil. To clean the catch pan, wash with warm soapy water, then rinse.
Thermometer - Wipe with warm soapy water; clean with plastic scrub ball.
Inside cooking module - Brush any debris off of burner tubes. DO NOT ENLARGE
BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water
and a water rinse.
Inside Lid - While lid is warm, wipe inside with paper towel to prevent grease build-up.
Flaking built-up grease resembles paint flakes.
Stainless steel surfaces - Wash with a soft cloth and a soap and water solution. Be
careful to scrub with the grain direction of the stainless steel.
Do not use cleaners that contain acid, mineral spirits or xylene. Rinse well after
cleaning.
Preserve Your Stainless Steel - Your grill or its cabinet, lid, control panel and shelves
may be made from stainless steel. To keep the stainless steel looking its best is a
simple matter. Clean it with soap and water, rinse with clear water and wipe dry. For
stubborn particles, the use of a non-metallic brush can be used.
Z_ IMPORTANT: Do not use a wire brush or abrasive cleaners
on the stainless steel surfaces of your grill as this will cause
scratches.
z_ IMPORTANT: When cleaning surfaces be sure to rub/wipe
in the direction of the grain to preserve the look of your
stainless steel.
IMPORTANT LP CYLINDER INFORMATION
Failure to fellow these DANGER statements exactly may result in a fire causing death or
serious injury.
AkDANGER
z_ NEVER store a spare LP Cylinder under or near this
barbecue.
z_ NEVER fill the tank beyond 80% full.
Your Weber ° gas grill is equipped for a cylinder supply system designed for
vapor withdrawal.
z_ WARNING: Only use this grill outdoors in a well=ventilated
area. Do not use in a garage, building, breezeway or any
other enclosed area.
The proper filling methods for the filling of your cylinder are by weight or volume, as
described in NFPA 58. Please make sure your filling station fills your LP cylinder by
weight or volume. Ask your filling station to read purging and filling instructions on the
LP cylinder before attempting to fill.
LEAK CHECK PREPARATION
CHECK THAT ALL BURNER VALVES ARE OFF
Valves are shipped in the "OFF" position, but you should check to be sure that they are
turned off. Check by pushing down and turning clockwise. If they do not turn, they are
off. Proceed to the next step. If they do turn continue turning them clockwise until they
stop, then they are off. Proceed to the next step.
CONNECTING THE LIQUID PROPANE CYLINDER
All Weber ¢ liquid propane gas grill regulators are equipped with a UL-listed tank
connection as per the latest edition of ANSI Z21.58. This will require a liquid propane
tank that is similarly equipped with a Type 1 connection in the tank valve. This Type 1
coupling allows you to make a fast and totally safe hookup between your gas grill and
your liquid propane tank. It eliminates the chance of leaks due to a POL fitting that is
not properly tightened. Gas will not flow from the tank unless the Type 1 coupling is fully
engaged into the coupling.
z_ WARNING: Make sure that the LP cylinder valve is closed.
Close by turning valve clockwise.
Ak DANGER
Do not use an open flame to check for gas leaks. Be sure
there are no sparks or open flames in the area while you
check for leaks. Sparks or flames will result in a fire or
explosion which can cause serious bodily injury or death,
and damage to property.
2
5
,/
1 Type 1 Valve
2 Hand Wheel
3 External Thread
4 Thermally Sensitive Nut
5 Propane Regulator
To connect the hose to the cylinder:
1) Pass the regulator hose through the side panel opening to the inside of the base
cabinet.
2) Locate hose retention clip (a) on regulator hose. Secure into slot (b) on underside
of tank scale.
z_ WARNING: The hose must be secured to the tank scale
with the Hose Retention Clip. Failure to do so could cause
damage to the hose resulting in a fire or explosion which
can cause serious bodily injury or death, and damage to
property.
The LP cylinder is installed inside the base cabinet, on the tank scale (right side).
3) Open base cabinet doors.
4) Turn the LP cylinder so the opening of the valve is either to the front, side or rear
of the Weber _ gas barbecue. Lift and hook the cylinder onto the fuel gauge.
5) Lift tank up into position on the tank scale.
6) Loosen the cylinder lock wing nut. Swing the cylinder lock down. Tighten the wing
nut.
Some LP tanks have differing top collar assembles. (The top collar is the metal
protective ring around the valve.) One series of tanks mount with the valve facing front
(a). The other tanks mount with the valve facing away from the fuel scale (b). Weber
recommends the use of cylinder manufacturer's Manchester and Worthington, with a
47.6 Ib water capacity. Other cylinders may be acceptable for use with the appliance
provided they are compatible with the appliance retention means (see illustrations).
7) Remove the plastic dust cover from the valve.
8) Screw the regulator coupling onto the tank valve, clockwise, or to the right. Hand-
tighten only.
Note: This is a new type of connection. It tightens clockwise and will not allow gas to
flow unless the connection is tighL The connection requires tightening by hand only.
z_ WARNING: Do not use a wrench to tighten the connection.
Using a wrench could damage the regulator coupling and
could cause a leak.
You will need: LP cylinder, a soap and water solution and a rag or brush to apply it.
9) Mix soap and water.
10) Turn on the cylinder valve.
11) Check for leaks by wetting the fitting with the soap and water solution and
watching for bubbles. If bubbles form, or if a bubble grows, there is a leak.
If there is a leak, turn off the gas and tighten the fitting.Turn the gas back on and
recheck with the soap and water solution.
If leak does not stop, contact the Customer Service Representative in your area using
the contact information on our web site. Log onto www.weber.com®. Do not use the
barbecue.
12) When leak checking is complete, turn gas supply OFF at the source and rinse
connections with water.
REMOVE CONTROL KNOBS & CONTROL PANEL FOR LEAK
TESTING
You will need: Phillips screwdrive_
1) Remove control knobs.
2) Remove screw and washer from back of control panel with a Phillips screwdriver.
3) Tilt the back edge of the control panel up. Push in on the front edge to release
locking tabs. Carefully pull control panel away from frame.
4) Disconnect the igniter wires from the ignition module.
5) Replace control panel when Leak Check is completed.
CHECK FOR GAS LEAKS
DANGER
Do not use an open flame to check for gas leaks. Be sure
there are no sparks or open flames in the area while you
check for leaks. Sparks or open flames will result in a fire or
explosion, which can cause serious bodily injury or death
and damage to property.
z_ WARNING: You should check for gas leaks every time you
disconnect and reconnect a gas fitting.
Note: Aft factory-made connections have been thoroughly checked for gas leaks. The
burners have been flame-tested. As a safety precaution however, you should recheck
aft fittings for leaks before using your WebeK Gas Barbecue. Shipping and handting
may loosen or damage a gas fitting.
z_ WARNING: Perform these leak checks even if your barbecue
was dealer or store assembled.
You will need: a soap and water solution, and a rag or brush to apply it.
Note. Since some leak test solutions, including soap and water, may be slightly
corrosive, all connections should be rinsed with water after checking for leaks.
If your grill has a side burner make sure the side burner is off.
To perform leak checks: open cylinder valve by turning the cylinder valve hand-wheel
counterclockwise.
z_ WARNING: Do not ignite burners when leak checking.
Check for leaks by wetting the connections with the soap and water solution and
watching for bubbles. If bubbles form or if a bubble grows, there is a leak.
Check:
1) Hose-to-manifold connection.
z_ WARNING: if there is a leak at connection (1), retighten the
fitting with a wrench and recheck for leaks with soap and
water solution, if a leak persists after retightening the fitting,
turn OFF the gas. DO NOT OPERATETHE GRILL. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com ®.
2) Regulator-to-cylinder connection.
3) The hose-to-regulator connection.
4) Valves-to-manifold connections.
z_ WARNING: If there is a leak at connections (2), (3) or (4),
turn OFF the gas. DO NOT OPERATE THE GRILL. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com ®.
When leak checks are complete, turn gas supply OFF at the source and rinse
connections with water.
*The grill illustrated may have
slight differences than the
model purchased.
(4)
Check:
1) Hose to manifold connection.
2) Side burner hose to manifold connection and side burner hose to side burner gas
line connection.
3) Side burner hose to side burner connection, side burner valve and orifice
connections.
z_ WARNING: If there is a leak at connection (1,2, or 3),
retighten the fitting with a wrench and recheck for leaks with
soap and water solution. If a leak persists after re-tightening
the fitting, turn OFF the gas. DO NOT OPERATE THE GRILL.
Contact the Customer Service Representative in your area
using the contact information on our web site.
Log onto www.weber.com ®.
4) Regulator to cylinder connection.
5) Hose to regulator connection.
6) Valves to manifold connections.
z_ WARNING: If there is a leak at connections (4, 5 or 6), turn
OFF the gas. DO NOT OPERATE THE GRILL. Contact the
Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com ®.
When leak checks are complete, turn gas supply OFF at the source and rinse
connections with water.
REFILLING THE LIQUID PROPANE CYLINDER
We recommend that you refill the LP cylinder before it is completely empty.
Removal of the LP cylinder
1) Close cylinder valve (turn clockwise).
2) Unscrew regulator coupling by turning counterclockwise, by hand only.
3) Loosen cylinder lock wing nut and turn cylinder lock up out of the way.
4) Lift cylinder off.
To fill, take the LP cylinder to a gas propane dealer, or look up "gas-propane" in the
phone book for other sources of LP gas.
Z_ WARNING: We recommend that your LP cylinder be filled
at an authorized LP gas dealer, by a qualified attendant,
who fills the cylinder by weight. IMPROPER FILLING IS
DANGEROUS.
z_ CAUTION: Place dust cap on cylinder valve outlet whenever
the cylinder is not in use. Only install the type of dust cap
on the cylinder valve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result in leakage of
propane.
(1)
*The grill illustrated may have
slight differences than the
model purchased.
(2)
(5)
CHECKING THE FUEL LEVEL IN YOUR TANK
Check the fuel level by viewing the color indicator level line on the side of the tank scale.
1) Empty
2) Medium
3) Full
(1)
0_
(2) (3)
SAFE HANDLING TIPS FOR LIQUID PROPANE GAS
CYLINDERS
o Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas.
LP gas is a gas at regular temperatures and pressures. Under moderate pressure,
inside a cylinder, LP gas is a liquid. As the pressure is released, the liquid readily
vaporizes and becomes gas.
LP gas has an odor similar to natural gas. You should be aware of this odor.
LP gas is heavier than air. Leaking LP gas may collect in low areas and prevent
dispersion.
To fill, take the LP cylinder to a gas propane dealer, or look up "gas-propane" in
the phone book for other sources of LP gas.
WARNING: We recommend that your LP cylinder be filled
at an authorized LP gas dealer, by a qualified attendant,
who fills the tank by weight. IMPROPER FILLING IS
DANGEROUS.
Air must be removed from a new LP cylinder before the initial filling. Your LP
dealer is equipped to do this.
The LP cylinder must be installed, transported and stored in an upright position.
LP cylinders should not be dropped or handled roughly.
Never store or transport the LP cylinder where temperatures can reach 125 ° F
(too hot to hold by hand - for example: do not leave the LP cylinder in a car on a
hot day).
Note: A refill will last about 18-20 hours of cooking time at norma! use. The fuel scale
will indicate the propane supply so you can refill before running ouL You do not have
to run out before you refill.
Treat "empty" LP cylinders with the same care as when full. Even when the LP
tank is empty of liquid there still may be gas pressure in the cylinder. Always
close the cylinder valve before disconnecting.
z_ CAUTION: Place dust cap on cylinder valve outlet whenever
the cylinder is not in use. Only install the type of dust cap
on the cylinder valve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result in leakage of
propane.
= Do not use a damaged LP cylinder. Dented or rusty LP cylinders or LP cylinders
with a damaged valve may be hazardous and should be replaced with a new one
immediately.
Liquid Propane (LP) Cylinder(a)
= The joint where the hose connects to the LP cylinder must be leak tested each
time the LP cylinder is reconnected. For example, test each time the LP cylinder is
refilled.
Be sure the regulator is mounted with the small vent hole pointed downward so
that it will not collect water. This vent should be free of dirt, grease, bugs etc.
The gas connections supplied with your Weber ¢ gas barbecue have been
designed and tested to meet 100% CSA and ANSI requirements.
WARNING: Replacement LP tanks must match the
regulator connection supplied with this barbecue.
LIQUID PROPANE CYLINDER REQUIREMENTS
Check to be sure cylinders have a D.O.T. certification (1), and date tested (2)
is within five years. Your LP gas supplier can do this for you.
All LP tank supply systems must include a collar to protect the cylinder valve.
The LP cylinder must be a 20-lb. size approximately (18_A inches high, 12_A
inches in diameter).
The cylinder must be constructed and marked in accordance with
the Specifications for LP - Gas Cylinders of the U.S. Department of
Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339,
Cylinders, Spheres and Tubes or Transportation of Dangerous Goods; and
Commission, as applicable.
IN CANADA
LIQUID PROPANE CYLINDER REQUIREMENTS
Note: Your retailer can help you match a replacement tank to your barbecue.
The LP cylinder must be constructed and marked in accordance with the
specifications for LP gas cylinders, T.C.
00/0_
LIGHTING
Summary lighting instructions are inside the left hand cabinet doo_
DANGER
Failure to open the lid while igniting the barbecue's burners,
or not waiting 5 minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flame=up
which can cause serious bodily injury or death.
CROSSOVER ®IGNITION SYSTEM
Note: The CrossoveF Ignition System ignites BURNER 1 with a spark from the igniter
electrode inside the Gas Catcher T"ignition chambe_ You generate the energy for the
spark by pushing the electronic ignition button. You will hear it sparking.
& WARNING: Check hose before each use of barbecue for nicks,
cracking, abrasions or cuts. If the hose is found to be damaged
in any way, do not use the barbecue. Replace using onlyWeber e
authorized replacement hose. Contact the Customer Service
Representative in your area using the contact information on
our web site. Log onto www.weber.com ®.
MAIN BURNER LIGHTING
1) Open the lid.
2) Make sure all burner control knobs are turned OFR (Push control knob down and
turn clockwise to ensure that it is in the OFF position.)
Z_ WARNING: The burner control knobs must be in the OFF
position before turning on the liquid propane cylinder tank
valve. If they are not in the OFF position, when you turn on
the LP cylinder valve, the "excess gas flow control" feature
will activate, limiting the flow of gas from the LP cylinder. If
this should occur, turn OFF the LP cylinder valve and burner
control knobs. Start over.
z_ DANGER
When the "excess gas flow control" feature is activated,
a small amount of gas is still flowing to the burners. After
turning OFF the cylinder vMve, wait at least 5 minutes for the
gas to clear before attempting to light the barbecue. Failure to
do so may result in an explosive flame=up, which can cause
serious bodily injury or death.
3) Turn the cylinder on by slowly turning the cylinder valve counterclockwise.
z_ WARNING: Do not lean over the open barbecue. Keep your
face and body at least one foot away from the matchlight
hole when lighting the barbecue.
4) Push BURNER 1 control knob down and turn to START/HI.
5) Push and hold the electronic ignition button. You will hear it sparking.
6) Check that the burner is lit by looking through the matchlight hole on the front of
the cooking box.You should see a flame.
z_ WARNING: If the burner does not light in five (5) seconds,
turn the Burner 1 control knob to OFF and wait 5 minutes
to let the gas clear before you try again or try to light with a
match.
7) After BURNER 1 is lit you can turn on BURNER 2 (and BURNER 3).
Note - Always light BURNER I first. The other burners ignite from BURNER 1.
TO EXTINGUISH
Push down and turn each burner control knob clockwise to the OFF position. Turn gas
supply OFF at the source.
MAIN BURNER LIGHTING
ELECTRONIC
IGNITER
*The grill illustrated may have
slight differences than the
model purchased.
MAIN BURNER MANUAL LIGHTING
z_ DANGER
Failure to open the lid while igniting the barbecue's burners, or
not waiting 5 minutes to allow the gas to clear if the barbecue
does not light, may result in an explosive flame-up which can
cause serious bodily injury or death.
1) Open the lid.
2) Make sure all burner control knobs are turned OFR (Push each knob down and
turn clockwise to ensure they are in the "OFF" position.)
Z_ WARNING:The burner control knobs must be in the OFF
position before turning on the liquid propane cylinder valve.
If they are not in the OFF position, when you turn on the
LP cylinder valve, the "excess gas flow control" feature will
activate, limiting the flow of gas from the LP cylinder. If this
should occur, turn OFF the LP tank valve and burner control
knobs. Start over.
MAIN BURNER MANUAL LIGHTING
*The grill illustrated may have
slight differences than the
model purchased.
DANGER
When the "excess gas flow control" feature is activated,
a small amount of gas is still flowing to the burners. After
turning OFF the cylinder and burner control knobs, wait at
least 5 minutes for the gas to clear before attempting to light
the barbecue. Failure to do so may result in an explosive
flame=up, which can cause serious bodily injury or death.
3) Turn the cylinder on by turning the cylinder valve counterclockwise.
4) Insert match holder with lit match into the matchlight hole in the front of the
cooking box.
z_ WARNING: Do not lean over open barbecue. Keep your face
and body at least one foot away from the matchlight hole
when lighting the barbecue.
5) Push BURNER 1 control knob down and turn to START/HI.
6) Check that the burner is lit by looking through the matchlight hole on the front of
the cooking box.You should see a flame.
WARNING: If the burner does not light in five seconds, turn
the Burner 1 control knob to OFF and wait 5 minutes to let
the gas clear before you try again.
7) After BURNER 1 is lit you can turn on BURNER 2 (and BURNER 3).
Note -A/ways fight BURNER 1 first.The other bumers ignite from BURNER 1.
TO EXTiNGUiSH
Push down and turn each burner control knob clockwise to the OFF position. Turn gas
supply OFF at the source.
MAIN BURNER MANUAL LIGHTING
*The grill illustrated may have
slight differences than the
model purchased.
LIGHTING THE SIDE BURNER
DANGER
Failure to open the lid while igniting the side burner, or not
waiting 5 minutes to allow the gas to clear if the side burner
does not light, may result in an explosive flame=up which can
cause serious bodily injury or death.
WARNING: Check hose before each use of barbecue for
nicks, cracking, abrasions or cuts. If the hose is found to
be damaged in any way, do not use the barbecue. Replace
using only Weber ® authorized replacement hose. Contact
the Customer Service Representative in your area using the
contact information on our web site. Log onto www.weber.
com e.
1) Open the side burner lid.
2) Check that the side burner valve is turned off (Push control knob in and turn
clockwise to ensure that it is in the "OFF" position), turn all burners not being
used to the "OFF" position (push in and turn clockwise).
WARNING:The burner control knobs must be in the OFF
position before turning on the liquid propane cylinder
valve. If they are not in the OFF position, when you turn on
the LP cylinder valve, the "excess gas flow control" feature
will activate, limiting the flow of gas from the LP cylinder.
If this should occur, turn OFF the LP tank valve and burner
control knobs. Start over.
DANGER
When the "excess gas flow control" feature is activated,
a small amount of gas is still flowing to the burners. After
turning OFF the cylinder and burner control knobs, wait at
least 5 minutes for the gas to clear before attempting to light
the barbecue. Failure to do so may result in an explosive
flame-up, which can cause serious bodily injury or death.
3) Turn the gas supply valve on.
4) Pushdownandturnthesideburnercontrolvalveto"HI".
5) Presstheigniterbuttonseveraltimessoitclickseachtime.
z_ CAUTION: Side burner flame may be difficult to see on a
bright sunny day.
WARNING: If the side burner does not light in five (5)
seconds:
a) Turn off the side burner control valve, main burners
and gas supply at source.
b) Wait 5 minutes to let the gas clear before you try
again, or try lighting with a match (see "Manually
Lighting the Side Burner").
i \.!
MANUALLY LIGHTING THE SIDE BURNER
DANGER
Failure to open the lid while igniting the side burner, or not
waiting 5 minutes to allow the gas to clear if the side burner
does not light, may result in an explosive flare=up that can
cause serious bodily injury or death.
1) Open the side burner lid.
2) Check that the side burner valve is turned off (Push control knob in and turn
clockwise to ensure that it is in the "OFF" position), turn all burners not being used
to the "OFF" position (push in and turn clockwise).
WARNING: The burner control knobs must be in the OFF
position before turning on the liquid propane cylinder valve.
If they are not in the OFF position, when you turn on the
LP cylinder valve, the "excess gas flow control" feature will
activate, limiting the flow of gas from the LP cylinder. If this
should occur, turn OFF the LP tank valve and burner control
knobs. Start over.
DANGER
When the "excess gas flow control" feature is activated,
a small amount of gas is still flowing to the burners. After
turning OFF the cylinder and burner control knobs, wait at
least 5 minutes for the gas to clear before attempting to light
the barbecue. Failure to do so may result in an explosive
flame=up, which can cause serious bodily injury or death.
3) Turn the gas supply valve on.
4) Put match in a match holder and strike match.
5) Hold match holder and lit match by either side of the side burner.
6) Push down and turn the side burner control valve to "HI".
z_ CAUTION: Side burner flame may be difficult to see on a
bright sunny day.
z_ WARNING: If the side burner does not light in five (5)
seconds:
a) Turn off the side burner control valve, main burners
and gas supply at source.
b) Wait 5 minutes to let the gas clear before you try
again.
PROBLEM CHECK
Burners burn with a yellow or orange flame, in Inspect Spider/Insect Screens for possible obstructions. Clean Spider/Insect Screens. (See Section 'Annual
conjunction with the smell of gas. (Blockage of holes.) Maintenance")
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated.
Symptoms:
Burners do not light. -or- Burners have a small
flickering flame in the "HF position. -or-
Barbecue temperature onmy reaches 250 ° to 300 °
in the "HF position.
Burner does not might, or flame is mow in "HI"
position.
Experiencing flare-ups:
CAUTION: Do not line the bottom tray
with aluminum foil.
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does Burner 1 light with a match?
Are you preheating barbecue in the prescribed manner?
Are the cooking grates and Flavorize¢ _bars heavily
coated with burned-on grease?
Is the bottom tray "dirty" and not allowing grease to flow
into catch pan?
CURE
To reset the excess flow safety device turn all burner control
knobs and the cylinder valve off. Disconnect the regulator
from the cylinder. Turn burner control knobs to "HI'.' Wait at
least 1 minute. Turn burner control knobs to "OFF Reconnect
the regulator to the cylinder. Turn cylinder valve on slowly.
Refer to "Lighting Instructions'.'
Refill LP cylinder.
Straighten fuel hose.
If you can light Burner 1 with a match, then check the
Crossover _ ignition system.
All burners on HI for 10 to 15 minutes for preheating.
Clean thoroughly. (See Section "Cleaning")
Clean bottom tray.
Burner flame pattern is erratic. Fmame is low when Are burners clean? Clean burners. (See Section "Maintenance'.')
burner is on "Hi'; Flames do not run the whole
length of the burner tube.
inside of midappears to be "peeling." (Resembmes The lid is porcelain enamel or stainless steel, not paint. Clean thoroughly. (See Section "Cleaning'.')
paint peeling.) It cannot "peeE What you are seeing is baked on grease
that has turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
Cabinet doors are not aligned. Check the adjustment pin on the bottom of each door. Loosen adjustment nut/s. Slide dooris until aligned. Tighten
nut.
if problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web
site. Log onto www.weber.com ®.
PROBLEM
Side Burner does not light.
CHECK
Is gas supply off?
The excess flow safety device, which is part
of the barbecue to cylinder connection, may
have activated.
CURE
Turn supply on.
To reset the excess flow safety device turn all burner control knobs and the cylinder
valve off. Disconnect the regulator from the cylinder. Turn burner control knobs to
START/HI. Wait at least 1 minute. Turn burner control knobs to "OFF". Reconnect
the regulator to the cylinder. Turn cylinder valve on slowly. Refer to "Lighting
Instructions".
Flame is low in "HI" position. Is the fuel hose bent or kinked? Straighten hose.
Push button ignition does not work. Does burner light with a match? If match lights burner, check igniter (see Sideburner Maintenance).
if problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com ®.
SIDE BURNER MAHNTENANCE
WARNING: All gas controls and supply valves should be in
the "OFF" position.
Make sure black wire is connected between the igniter and electrode.
Make sure white wire is connected between the igniter and grounding clip.
Spark should be a white/blue color, not yellow.
1) Igniter Wire
2) Ground wire
3) Burner
Side Burner Grate
Side Burner cap
Side Burner Ring & Head
igniter Electrode
Control Knob
igniter
(3)
WEBER ®SPIDER/INSECT SCREENS
Your Weber _ gas barbecue, as well as any outdoor gas appliance, is a target for spiders
and other insects. They can nest in the venturi section (1) of the burner tubes. This
blocks the normal gas flow, and can cause the gas to flow back out of the combustion
air opening. This could result in a fire in and around the combustion air openings, under
the control panel, causing serious damage to your barbecue.
The burner tube combustion air opening is fitted with a stainless steel screen (2) to
prevent spiders and other insects access to the burner tubes through the combustion air
openings.
We recommend that you inspect the Spider/mnsect screens at meastonce a year.
(See Section "Annual Maintenance".) Also inspect and clean the the Spider/Insect
screens if any of the following symptoms should ever occur:
1) The smell of gas in conjunction with the burner flames appearing yellow and lazy.
2) Barbecue does not reach temperature.
3) Barbecue heats unevenly.
4) One or more of the burners do not ignite.
DANGER
Failure to correct the above mentioned symptoms may result
in a fire, which can cause serious bodily injury or death, and
cause damage to property.
ANNUALMAINTENANCE
iNSPECTiON AND CLEANING OF THE SPIDER/INSECT SCREENS
To inspect the Spider/Insect screens, remove the control panel. If there is dust or dirt on
the screens, remove the burners for cleaning the screens.
Brush the Spider/Insect screens lightly with a soft bristle brush (i.e. an old toothbrush).
z_ CAUTION: Do not clean the Spider/Insect screens with hard
or sharp tools. Do not disJodge the Spider/Insect screens or
enJarge the screen openings.
Lightly tap the burner to get debris and dirt out of the burner tube. Once the Spider/
Insect screens and burners are clean replace the burners.
If the Spider/Insect screen becomes damaged or cannot be cleaned, please contact the
Customer Service Representative in your area using the contact information on our web
site. Log onto www.weber.com ®.
BURNER FLAME PATTERN
The WebeP gas barbecue burners have been factory set for the correct air and gas
mixture. The correct flame pattern is shown.
1) Burner tube
2) Tips occasionally flicker yellow
3) Light blue
4) Dark blue
If the flames do not appear to be uniform throughout the burner tube, follow the burner
cleaning procedures.
MAIN BURNER CLEANING PROCEDURE
Turn off the gas supply.
Remove the manifold (See "Replacing Main Burners").
Look inside each burner with a flashlight.
Clean the inside of the burners with a wire (a straightened-out coat hanger will work).
Check and clean the air shutter opening at the ends of the burners. Check and clean
the valve orifices at the base of the valves. Use a Steel bristle brush to clean outside of
burners. This is to make sure all the burner ports are fully open.
z_ CAUTION: Do not enlarge the burner ports when cleaning.
REPLACING MAIN BURNERS
1) Your Webei 4egas barbecue must be OFF and cool.
2) Turn gas OFF at source.
3) To remove control panel:
(a) Take off the burner control knobs.
(b) Remove screw and washer from back of control panel with a Phillips screwdriver.
(c) Tilt the back edge of the control panel up. Push in on the front edge to release
locking tabs.
(d) Disconnect the igniter wires from the ignition module.
(e) Carefully pull control panel away from frame.
4) Remove the two threaded 7/16" hex screws (a) that hold the manifold support
bracket to the cooking box. Pull the manifold and valve assembly towards you, at
the same time lift the manifold assembly up to release the manifold brackets from
the frame assembly. (b).
5) Slide the burner assembly out from under the guide screw and washer (a) in the
corners of the cooking box.
6) Lift and twist the burner assembly slightly, to separate the crossover tube (b) from
the burners. Remove the burners from the cooking box.
7) To reinstall the burners, reverse 3) through 7).
z_ CAUTION: The burner openings (c) must be positioned
properly over the valve orifices (d).
Check proper assembly before fastening manifold in place.
z_ WARNING: After reinstalling the gas lines, they should be
leak checked with a soap and water solution before using the
barbecue. (See Step: "Check for gas leaks.")
CROSSOVER ® IGNITION SYSTEM OPERATIONS
If The Crossover ¢ Ignition System fails to ignite the BURNER 1, light BURNER 1 with a
match. If BURNER 1 lights with a match, then check the Electronic Ignition System.
o Check that both of the ignition wires are attached at the igniter module properly.
Check that the ignition wire is attached at the ceramic igniter properly.
Check that the ceramic igniter assembly (A) is fully positioned into burner tube 1
igniter channel (B).
Check that the ceramic igniter is properly positioned over the burner holes on
BURNER 1.
Check that the Electronic Ignition Button is working by listening and looking for
sparks at BURNER 1.
REPLACE BATTERY iF NECESSARY
AAA alkaline battery only. See illustration:
If the Electronic Ignition System still fails to light, contact the Customer Service
Representative in your area using the contact information on our web site. Log
onto www.weber.com ®.
\
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Genesis EP -310/320 Le manuel du propriétaire

Catégorie
Barbecues
Taper
Le manuel du propriétaire
Ce manuel convient également à