Weber E310LP-2011 Le manuel du propriétaire

Marque: Weber

Modèle: E310LP-2011

Catégorie: Barbecues

Taper: Le manuel du propriétaire

310

YOU MUST READ THiS OWNER'S GUIDE

BEFORE OPERATING YOUR GAS GRILL.

/k DANGER

if you smeJl gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. if odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

Leaking gas may cause a fire or explosion

which can cause serious bodily injury,

death, or damage to property.

ik WARNING:

1. Do not store or use gasoJine or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

[/k WARNING: Follow all leak-check

procedures carefully in this manual prior

to barbecue operation. Do this even if the

barbecue was dealer-assembled.

r--

NOTICE TO iNSTALLER: These instructions

must be left with the owner and the owner

should keep them for future use.

THIS GAS APPLIANCE iS DESIGNED FOR 1OUTDOOR USE ONLY.

z_ WARNING: Do not ignite this appliance

without first reading the BURNER

iGNiTiON sections of this manual.

A_'_ MEMBER

Nati0nsiPROPANEGAS A_ciati0_

5651/, 02/28/11 LP

US ENGLISH

DANGER

Failure to follow the Dangers, Warnings and Cautions contained in this Owner's Manual may result in serious bodily injury or

death, or in a fire or an explosion causing damage to property.

WARNINGS

z_ Do not store a spare or disconnected liquid propane

cylinder under or near this barbecue.

z_ improper assembly may be dangerous. Please follow the

assembly instructions carefully.

z_ After a period of storage, and/or nonuse, the Webe_ gas

barbecue should be checked for gas leaks and burner

obstructions before use. See instructions in this manual for

correct procedures.

z_ Do not operate the Weber _ gas barbecue if there is a gas

leak present.

z_ Do not use a flame to check for gas leaks.

z_ Combustible materials should never be within 24 inches (61

cm) of the back or sides of your Weber ®gas barbecue.

z_ Do not put a barbecue cover or anything flammable on, or in

the storage area under the barbecue.

z_ Your Weber ®gas barbecue should never be used by

children. Accessible parts of the barbecue may be very hot.

Keep young children away while it is in use.

z_ You should exercise reasonable care when operating your

Weber ®gas barbecue, it will be hot during cooking or

cleaning and should never be left unattended, or moved

while in operation.

Z_ Should the burners go out while in operation, turn all

gas valves off. Open the lid and wait five minutes before

attempting to relight, using the igniting instructions.

z_ Do not use charcoal or lava rock in your Weber ®gas

barbecue.

Z_ Never lean over open grill or place hands or fingers on the

front edge of the cookbox.

Z_ Should a grease fire occur, turn off all burners and leave lid

closed until fire is out.

Z_ Do not enlarge valve orifices or burner ports when cleaning

the valves or burners.

Z_ The Weber ®gas barbecue should be thoroughly cleaned on

a regular basis.

Z_ Liquid propane gas is not natural gas. The conversion or

attempted use of natural gas in a liquid propane unit or

liquid propane gas in a natural gas unit is dangerous and

will void your warranty.

Z_ Do not attempt to disconnect any gas fitting while your

barbecue is in operation.

Z_ Use heat-resistant barbecue mitts or gloves when operating

barbecue.

Z_ Keep any electrical supply cord and the fuel supply hose

away from any heated surfaces.

Z_ Combustion byproducts produced when using this product

contain chemicals known to the state of California to cause

cancer, birth defects, or other reproductive harm.

Z_ Do not use this barbecue unless all parts are in place. The

unit must be properly assembled according to the assembly

instructions.

Z_ Do not build this model of grill in any built-in or slide-in

construction, ignoring this Warning could cause a fire or

an explosion that can damage property and cause serious

bodily injury or death.

Z_ Proposition 65 Warning: Handling the brass material on

this product exposes you to lead, a chemical known to the

state of California to cause cancer, birth defects or other

reproductive harm.

(Wash hands after handling this product.)

LIQUID PROPANE GAS UNITS ONLY:

z_ Use the pressure regulator and hose assembly that is

supplied with your Weber ®gas barbecue.

Z_ Do not attempt to disconnect the gas regulator and hose

assembly or any gas fitting while your barbecue is in

operation.

Z_ A dented or rusty liquid propane cylinder may be hazardous

and should be checked by your liquid propane supplier. Do

not use a liquid propane cylinder with a damaged valve.

Z_ Although your liquid propane cylinder may appear to be

empty, gas may still be present, and the cylinder should be

transported and stored accordingly.

z_ if you see, smell or hear the hiss of escaping gas from the

liquid propane cylinder:

1. Move away from liquid propane cylinder.

2. Do not attempt to correct the problem yourself.

3. Call your fire department.

WARNINGS .......................................... 2

TABLE OF CONTENTS................................. 3

EXPLODED VIEW 310 ................................. 4

EXPLODED VIEW LIST 310 ............................. 5

WARRANTY ......................................... 6

GENERAL INSTRUCTIONS ............................. '7

CANADIAN INSTALLATION .......................................... 7

OPERATING ...................................................... 7

STORAGE AND/OR NONUSE ........................................ 7

GASINSTRUCTIONS .................................. 8

SAFE HANDLING TIPS FOR LIQUID PROPANE GAS CYLINDERS .......... 8

IMPORTANT LP CYLINDER INFORMATION ............................ 9

LEAK CHECK PREPARATION ........................................ 9

CHECK FOR GAS LEAKS .......................................... 11

REFILLING THE LIQUID PROPANE CYLINDER ......................... 12

BEFORE USING THE GRILL ........................... 13

FUEL LEVEL .................................................... 13

SLIDE OUT GREASE TRAY AND DISPOSABLE DRIP PAN ................ 13

ELECTRONIC IGNITER INSPECTION ................................ 13

HOSE INSPECTION .............................................. 13

MAIN BURNER IGNITION & USAGE..................... 14

MAIN BURNER IGNITION .......................................... 14

TO EXTINGUISH ................................................. 14

MAIN BURNER MANUAL IGNITION ................................. 15

TO EXTINGUISH ................................................. 15

GRILLING TIPS & HELPFUL HINTS ..................... 16

PREHEATING ................................................... 16

COVERED COOKING ............................................. 16

DRIPPINGS AND GREASE ........................................ 16

FLAVORIZER ® SYSTEM ........................................... 16

TROUBLESHOOTING................................. I'7

MAINTENANCE ..................................... 18

CLEANING ...................................................... 18

WEBER ®SPIDER/INSECT SCREENS ................................ 18

BURNER TUBES CLEANING OR REPLACEMENT ...................... 19

ELECTRONIC IGNITION SYSTEM OPERATIONS ....................... 21

ANNUAL MAINTENANCE .......................................... 22

Genesis_310 LP US 061110

12--

1. Thermometer 16. Catch Pan 31. Wind Deflector

Term6metro Plato recolector Deflector de viento

Thermometre Egouttoir Deflecteur de vent

2. Thermometer Bezel 17. Catch Pan Holder 32. Control Knob

Moldura decorativa del term6metro Soporte del plato recolector Perilla de control

Collerette du thermometre Support de I'egouttoir Bouton de commande

3. Shroud 18. Left Frame Panel 33. Manifold Hose

Cubierta Panel izquierdo del bastidor Manguera del multiple

Etui Panneau du ch&ssis gauche Tuyau du collecteur

4. Handle 19. Front FrameSupport 34. Bulkhead

Asa Soporte delantero del bastidor Tabique divisorio

Poignee Support du ch&ssis avant T_te du br_leur

5. Warming Rack 20. Left Door 35. Hose/Regulator

Rejilla de calentamiento Puerta izquierda Manguera / Regulador

Grille de maintien au chaud Porte gauche Tuyau / Regulateur

6. Left SideTable 21. Right Door 36. Right Frame Panel

Mesa lateral izquierda Puerta derecha Panel derecho del bastidor

Tablette lat@ale gauche Porte droite Panneau du ch&ssis droit

7. Cooking Grate 22. Door Handle 37. Back Panel

Parrilla de coccJ6n Asa de la puerta Panel trasero

Grille de cuisson Poignee de la porte Panneau arriere

8. Burner Tube 23. Shroud Hardware 38. Tank Scale

Tubo quemador Accesorios de la cubierta B#,scula del tanque

Tube du brQleur Quincaillerie de I'etui Graduation de la bouteille de gaz

9. FJavorizer ®Bar 24. Right SideTable 39. Bottom Panel

Barra Flavorizer _ Mesa lateral derecha Panel inferior

Barre FlavorizeF _ Tablette laterale droite Panneau inferieur

10. Igniter 25. Manifold 40. Tank Glides

Encendedor Multiple Deslizaderas del tanque

Allumeur Collecteur Glissieres de la bouteille de gaz

11. Cookbox 26. Heat Shield 41. Caster

Caja de cocci6n Pantalla contra el calor Rueda giratoria

Boitier de cuisson Protection anti-chaleur Roulette

12. Heat Deflector 27. Wire Clips 42. Matchstick Holder

Deflector de calor Grapas de alambre Portacerillos

Deflecteur de chaleur Pinces de retenue des c&bles Porte-allumettes

13. Slide Out GreaseTray

Bandeja deslizante de grasa

Plateau d'evacuation des graisses amovible

28. Control Panel

Tablero de control

Panneau de commande

43. Locking Caster

Rueda giratoria con bloqueo

Roulette & verrouillage

14. Rear Frame Support

Soporte posterior del bastidor

Support de ch&ssis arriere

29. Igniter Button

Bot6n de encendido

Bouton de I'allumeur

15. Disposable Drip Pan

Bandeja de gored desechable

Egouttoir jetable

30. Igniter Module

M6dulo de encendido

Module de I'allumeur

Weber-Stephen Products LLC (Weber) hereby warrants to the ORIGINAL PURCHASER of this

WebeP gas grill that it will be free of defects in material and workmanship from the date of purchase

as follows:

Aluminum castings: 25-years (2 years on paint: excludes fading)

Stainless steel shroud: 25-years

Porcelain-enameled shroud: 25-years

Stainless steel burner tubes: t0-years

Stainless steel cooking grates: 5-years no rust through or burn through

Stainless steel Flavorizer ® bars: 5-years no rust through or burn through

Porcelain-enameled cast-iron cooking grates: 5-year no rust through or burn through

Porcelain-enameled cooking grates: 3-years no rust through or burn through

Porcelain-enameled Flavorizer ® bars: 2-years no rust through or burn through

Infrared rotisserie burner: 2-years

All remaining parts: 2-years

when assembled and operated in accordance with the printed instructions accompanying it. Weber

may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR

SALES SLIP OR INVOICE.

This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under

normal use and service and which on examination shall indicate, to Weber's satisfaction, they are

defective. Before returning any parts, contact the Customer Service Representative in your area

using the contact information on our website. If Weber confirms the defect and approves the claim,

Weber will elect to replace such parts without charge. If you are required to return defective parts,

transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage

prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse,

misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or

service, or failure to perform normal and routine maintenance, including but not limited to damage

caused by insects within the burner tubes, as set out in this owner's manual.

Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes

or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not

covered by this Limited Warranty.

There are no other express warrants except as set forth herein and any applicable implied warranties

of merchantability and fitness are limited in duration to the period of coverage of this express written

Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this

limitation may not apply to you.

Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the

exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not

apply to you.

Weber does not authorize any person or company to assume for it any other obligation or liability in

connection with the sale, installation, use, removal, return, or replacement of its equipment; and no

such representations are binding on Weber.

This Warranty applies only to products sold at retail.

WEBER-STEPHEN PRODUCTS LLC

Customer Service Center

1890 Roaelle Road, Suite 308

Schaumburg, IL 60195

USA

For replacement parts calh

1-800-446-1071

Visit www.weber.com ®, select your country of origin, and regiater your grill today. ®

Your Webeff _gas barbecue is a portable outdoor cooking appliance. With the Weber ¢

gas barbecue you can grill, barbecue, roast and bake with results that are difficult to

duplicate with indoor kitchen appliances.The closed lid and Flavorizer _ bars produce

that "outdoor" flavor in the food.

The Weber ¢ gas barbecue is portable so you can easily change its location in your yard

or on your patio. Portability means you can take your Weber ¢ gas barbecue with, if you

meve.

Liquid Propane (LP) gas supply is easy to use and gives you more cooking control than

charcoal fuel.

o These instructions will give you the minimum requirements for assembling your

Webei _ gas barbecue. Please read the instructions carefully before using your

Weber ¢ gas barbecue. Improper assembly can be dangerous.

Not for use by children.

If there are local codes that apply to portable gas grills, you will have to conform to

them. Installation must conform with local codes or, in the absence of local codes,

with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and

Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code,

B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and

CSA Z240 RV Series, Recreational Vehicle Code, as applicable.

The pressure regulator supplied with the Webeff _gas barbecue must be used.This

regulator is set for 11 inches of water column (pressure).

This Webeff _gas barbecue is designed for use with liquid propane (LP) gas only. Do

not use with natural (piped in city) gas. The valves, orifices, hose and regulator are for

LP gas only.

Do not use with charcoal fuel.

Check that the area under the control panel and the slide out grease tray are free

from debris that might obstruct the flow of combustion or ventilation air.

The areas around the LP cylinder must be free and clear from debris.

Replacement pressure regulators and hose assemblies must be those specified by

Weber-Stephen Products LLC. ®

CANADIAN INSTALLATION

These instructions, while generally acceptable, do not necessarily comply with the

Canadian Installation codes, particularly with piping above and below ground. In

Canada the installation of this appliance must comply with local codes and/or Standard

CSA-B149.2 (Propane Storage and Handling Code).

OPERATING

z_ WARNING: Only use this barbecue outdoors in a well-

ventilated area. Do not use in a garage, building, breezeway

or any other enclosed area.

z_ WARNING: Keep ventilation openings for cylinder enclosure

free and clear from debris.

z_ WARNING: Your Weber ®gas barbecue shall not be used

under overhead combustible construction.

z_ WARNING: Your Weber ®gas barbecue is not intended to be

installed in or on recreational vehicles and/or boats.

z_ WARNING: Do not use the barbecue within 24 inches of

combustible materials.

z_ WARNING: The entire cookbox gets hot when in use. Do not

leave unattended.

z_ WARNING: Keep electrical supply cord and the fuel supply

hose away from heated surfaces.

z_ WARNING: Keep the cooking area clear of flammable vapors

and liquids such as gasoline, alcohol, etc., and combustible

materials.

z_ WARNING: Never store an extra (spare) LP cylinder under or

near the Weber _ gas barbecue.

z_ WARNING: The LP cylinder used with your barbecue must

be with a listed OPD (Overfilling Prevention Device) and

a QCCl or Type 1 (CGA810) cylinder connection. The

cylinder connection must be compatible with the barbecue

connection.

STORAGE AND/OR NONUSE

The gas must be turned off at the liquid propane cylinder when the WebeP _gas

barbecue is not in use.

When the Weber ¢ gas barbecue is stored indoors, the gas supply must be

DISCONNECTED and the LP cylinder stored outdoors in a well-ventilated space.

LP cylinder must be stored outdoors in a well -ventilated area out of reach of children.

Disconnected LP cylinder must not be stored in a building, garage or any other

enclosed area.

When the LP cylinder is not disconnected from the Weber _ gas barbecue, the

appliance and LP tank must be kept outdoors in a well-ventilated space.

The Weber ¢ gas barbecue should be checked for gas leaks and any obstructions

in the burner tubes before using. (Refer to "MAINTENANCE/ANNUAL

MAINTENANCE").

Check that the areas under the control panel and the drip tray are free from debris

that might obstruct the flow of combustion or ventilation air.

The Spider/Insect screens should also be checked for any obstructions. (Refer to

"MAINTENANCE/ANNUAL MAINTENANCE"). ®

SAFE HANDLING TIPS FOR LIQUID PROPANE GAS CYLINDERS

, Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas. LP

gas is a gas at regular temperatures and pressures. Under moderate pressure, inside

a cylinder, LP gas is a liquid. As the pressure is released, the liquid readily vaporizes

and becomes gas.

, LP gas has an odor similar to natural gas.You should be aware of this odor.

LP gas is heavier than air. Leaking LP gas may collect in low areas and prevent

dispersion.

To fill, take the LP cylinder to a gas propane dealer, or look up "gas-propane" in the

phone book for other sources of LP gas.

WARNING: We recommend that your LP cylinder be filled

at an authorized LP gas dealer, by a qualified attendant,

who fills the tank by weight. IMPROPER FILLING IS

DANGEROUS.

, Air must be removed from a new LP cylinder before the initial filling.Your LP dealer is

equipped to do this.

, The LP cylinder must be installed, transported, and stored in an upright position. LP

cylinders should not be dropped or handled roughly.

, Never store or transport the LP cylinder where temperatures can reach 125° F (too hot

to hold by hand -- for example: do not leave the LP cylinder in a car on a hot day).

Note: A refill will last about 18-20 hours of cooldng time at normal use. The fuel scale, a

feature on some of our grills, will indicate the propane supply so you can refill before

running out. You do not have to run out before you refill.

, Treat "empty" LP cylinders with the same care as when full. Even when the LP tank

is empty of liquid there still may be gas pressure in the cylinder. Always close the

cylinder valve before disconnecting.

z_ CAUTION: Place dust cap on cylinder valve outlet whenever

the cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage of

propane.

= Do not use a damaged LP cylinder. Dented or rusty LP cylinders or LP cylinders

with a damaged valve may be hazardous and should be replaced with a new one

immediately.

= The joint where the hose connects to the LP cylinder must be leak tested each time

the LP cylinder is reconnected. For example, test each time the LP cylinder is refilled.

= Be sure the regulator is mounted with the small vent hole pointed downward so that it

will not collect water. This vent should be free of dirt, grease, bugs etc.

= The gas connections supplied with your Weber ¢ gas appliance have been designed

and tested to meet 100% CSA and ANSI requirements.

WARNING: Replacement LP tanks must match the regulator

connection supplied with this Weber _ gas appliance.

Liquid Propane Cylinder Requirements

, Check to be sure cylinders have a D.O.T. certification (1), and date tested (2) is within

five years of use.Your LP gas supplier can do this for you.

= All LP tank supply systems must include a collar to protect the cylinder valve.

= The LP cylinder must be a 20-lb. size approximately 18_Ainches high, 12_Ainches in

diameter.

= The cylinder must be constructed and marked in accordance with the Specifications

for LP - Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the

National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes or

Transportation of Dangerous Goods; and Commission, as applicable.

Canadian Liquid Propane Cylinder Requirements

Note: Your retailer can help you match a replacement tank to your barbecue.

, The LP cylinder must be constructed and marked in accordance with the

specifications for LP gas cylinders, T.C. ®

IMPORTANT LP CYLINDER INFORIVIATION

z_ DANGER

NEVER store a spare LP cylinder under or near Weber + gas

appliances. NEVER fill the tank beyond 80% full. Failure to

follow these statements exactly may result in a fire causing

death or serious injury.

Weber ¢ gas appliances are equipped for a cylinder supply system designed for vapor

withdrawal.

z_ WARNING: Only use Weber ®gas appliances outdoors in

a well=ventilated area. Do not use in a garage, building,

breezeway or any other enclosed area.

The proper filling methods for the filling of your cylinder are by weight or volume, as

described in NFPA 58. Please make sure your filling station fills your LP cylinder by

weight or volume. Ask your filling station to read purging and filling instructions on the LP

cylinder before attempting to fill. ®

LEAK CHECK PREPARATION

Check That All Burner Valves Are Off

Valves are shipped in the OFF position, but you should check to be sure that they are

turned off. Check by pushing down and turning clockwise. If they do not turn, they are off.

If they do turn, continue turning them clockwise until they stop, then they are off.

The Liquid Propane Cylinder

All Weber ¢ liquid propane gas grill regulators are equipped with a UL-Listed tank

connection as per the latest edition of ANSI Z21.58. This will require a liquid propane

tank that is similarly equipped with a Type 1 connection in the tank valve. This Type 1

coupling allows you to make a fast and totally safe hookup between your gas grill and

your liquid propane tank. It eliminates the chance of leaks due to a POL fitting that is

not properly tightened. Gas will not flow from the tank unless the Type 1 coupling is fully

engaged into the coupling.

z_ WARNING: Make sure that the LP cylinder valve is closed.

Close by turning valve clockwise.

1 Type 1 Valve

2 Hand Wheel

3 External Thread

4 Thermally Sensitive Nut

5 Propane Regulator

z_ DANGER

Do not use an open flame to check for gas leaks. Be sure

there are no sparks or open flames in the area while you

check for leaks. Sparks or flames will result in a fire or

explosion which can cause serious bodily injury or death,

and damage to property.

A) Open base cabinet doors. Bring regulator and hose forward out of cabinet (1).

B) Locate hose retention clip (2) on regulator hose. Secure into slot (3) on underside of

tank scale.

z_ WARNING: The hose must be secured to the tank scale

with the Hose Retention Clip. Failure to do so could cause

damage to the hose resulting in a fire or explosion which

can cause serious bodily injury or death, and damage to

property.

Some LP tanks have differing top collar assembles. (The top collar is the metal

protective ring around the valve.) One series of tanks mount with the valve facing front

(4). The other tanks mount with the valve facing away from the fuel scale (5). Weber

recommends the use of cylinder manufacturer's Manchester and Worthington, with a

47.6 Ib water capacity. Other cylinders may be acceptable for use with the appliance

provided they are compatible with the appliance retention means (see illustrations).

The LP cylinder is installed inside the base cabinet, on the tank scale (right side).

C) Loosen cylinder lock wing nut. Swing cylinder lock up (6).

D) Turn the LP cylinder so the opening of the valve is either to the front or side of the

Weber ¢ gas barbecue.

E) Lift tank up into position on the tank scale (7).

F) Swing the cylinder lock down. Tighten the wing nut.

Connect The Hose To The Cylinder

A) Remove the plastic dust cover from the valve.

B) Screw the regulator coupling onto the tank valve, clockwise, or to the right (8).

Hand-tighten only.

Note: This connection tightens clockwise and will not allow gas to flow unless the

connection is tight. The connection requires tightening by hand onljz

Z_ WARNING: Do not use a wrench to tighten the connection.

Using a wrench could damage the regulator coupling and

could cause a leak. ÷

_/_l!;i!iiiiiiiiiiiii!i

_iiiiiiii;i!i!ilill

Remove Control Knobs & Control Panel For Leak Testing

You will need: Phillips screwdriver.

A) Remove control knobs, igniter button, retention nut, and battery (1).

B) Remove screws from wind deflector with a Phillips screwdriver (2).

C) Tilt end of wind deflector down and slide wind deflector away to remove (3).

D) Let igniter module dangle from wires. Do not disconnect (4).

E) Remove screws from underside of control panel with Phillips screwdriver (5).

F) Lift control panel up slightly, tilt up front edge and gently lift up (6).

G) Replace control panel and wind deflector when leak check is completed. ¢

CHECK FOR GAS LEAKS

DANGER

Do not use an open flame to check for gas leaks. Be sure

there are no sparks or open flames in the area while you

check for leaks. Sparks or open flames will result in a fire or

explosion, which can cause serious bodily injury or death

and damage to property.

Note: All factory-made connections have been thoroughly checked for gas leaks. The

burners have been flame-tested. As a safety precaution however, you should recheck all

fittings for leaks before using your Weber- gas barbecue. Shipping and handling may

loosen or damage a gas fitting.

Z_ WARNING: The gas connections of your gas grill have been

factory tested. We do however recommend that you leak

check all gas connections before operating your gas grill.

z_ WARNING: Perform these leak checks even if your barbecue

was dealer or store assembled.

If your grill has a side burner make sure the side burner is turned off.

Turn on gas supply at source.

WARNING: Do not ignite burners when leak checking.

You will need: A soap and water solution and a rag or brush to apply it.

A) Mix soap and water.

B) Turn on gas supply (1).

C) Check for leaks by wetting the fitting with the soap and water solution and watching

for bubbles. If bubbles form, or if a bubble grows, there is a leak.

If there is a leak, turn off the gas and tighten the fitting. Turn the gas back on and

recheck with the soap and water solution. If leak does not stop do not use the

barbecue. Contact the customer service representative in your area using the

contact information on our web site. Log onto www.weber.com ®.

D) When leak checking is complete, turn gas supply off at the source and rinse

connections with water.

Note: Since some leak test solutions, including soap and water, may be slightly

corrosive, a!l connections should be rinsed with water after checking for leaks.

z_ WARNING: You should check for gas leaks every time you

disconnect and reconnect a gas fitting.

_iii iiii_:

Check

A) Regulator hose to bulkhead connection (1).

B) Main gas line to bulkhead connection (2).

C) Main gas line to manifold connections (3).

z_ WARNING: If there is a leak at connections (1,2, or 3),

retighten the fitting with a wrench and recheck for leaks with

soap and water solution. If a leak persists after retightening

the fitting, turn OFF the gas. DO NOT OPERATE THE GRILL.

Contact the Customer Service Representative in your area

using the contact information on our web site.

Log onto www.weber.com ®.

D) Regulator hose to cylinder connection (4).

E) Regulator hose to regulator connection (5).

F) Valves to manifold connections (6).

WARNING: If there is a leak at connections (4, 5, or 6), turn

OFF the gas. DO NOT OPERATE THE GRILL. Contact the

Customer Service Representative in your area using the

contact information on our web site.

Log onto www.weber.com ®.

When leak checks are complete, turn gas supply OFF at the source and rinse

connections with water.

Reinstall Control Panel

You will need: Phillips screwdriver.

A) Position top edge of control panel on tabs of frame. Push down into position.

B) Reinstall igniter module.

C) Slide both shorter wind deflector tabs toward inside edge of control panel while you

slide longer tab over outside edge. Seek previous illustrations for reference.

D) Line up screws with screw holes on both control panel bracket and frame.

E) Tighten screws.

F) Place corresponding control knobs onto valve stems. ®

The grimmimmustratedmay

have smight differences

than the model purchased.

REFILLING THE LIQUID PROPANE CYLINDER

We recommend that you refill the LP cylinder before it is completely empty.

Removal of the LP cylinder:

A) Close cylinder valve (turn clockwise) (1).

B) Unscrew regulator coupling by turning counterclockwise, by hand only (2).

C) Loosen cylinder lock wing nut and turn cylinder lock up out of the way (3).

D) Lift cylinder off.

To fill, take the LP cylinder to a gas propane dealer, or look up "gas-propane" in the

phone book for other sources of LP gas.

WARNING: We recommend that your LP cylinder be filled

at an authorized LP gas dealer, by a qualified attendant,

who fills the cylinder by weight. IMPROPER FILLING IS

DANGEROUS.

z_ CAUTION: Place dust cap on cylinder valve outlet whenever

the cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage of

propane. ÷

FUEL LEVEL

Check the fuel level by viewing the color indicator level line, located on the side of the

tank scale.

A) Empty (1)

B) Medium (2)

C) Full (3) ®

[] [] []

IIII

SLIDE-OUT GREASE TRAY AND DISPOSABLE DRIP PAN

Your grill was built with a grease collection system. Check the slide-out grease tray and

disposable drip pan for grease build-up each time you use your grill.

Remove excess grease with a plastic spatula; see illustration. When necessary, wash

the grease tray and drip pan with a soap and water solution, then rinse with clean water.

Replace the disposable drip pan as needed.

z_ WARNING: Check the slide=out grease tray and disposable

drip pan for grease build=up before each use. Remove

excess grease to avoid a grease fire. A grease fire can cause

serious bodily injury or damage to property.

z_ CAUTION: Do not line the slide=out grease tray with

aluminum foil.

ELECTRONIC IGNITER INSPECTION

Verify that your AA battery (alkaline only) is in good condition and that it is installed

correctly (1). Some batteries have a plastic protective wrap around them. This plastic

must be removed. Do not confuse this plastic with the battery label. ®

HOSEINSPECTION

The hose should be inspected for any signs of cracking.

WARNING: Check hose before each use of barbecue for

nicks, cracking, abrasions or cuts. If the hose is found to

be damaged in any way, do not use the barbecue. Replace

using only Weber ®authorized replacement hose. Contact

the Customer Service Representative in your area using the

contact information on our web site.

Log onto www.weber.com ®.

MAIN BURNER IGNITION

Summary lighting instructions are inside the left hand cabinet door.

_ DANGER

Failure to open the lid while igniting the barbecue's burners,

or not waiting five minutes to allow the gas to clear if the

barbecue does not light, may result in an explosive flare-up

wh!ch can cause serious bodi!Y !nJu_ ?r de,!h:

Electronic ignition System

Note:Each control knob operates anindividual bume_ TheElectronic Ignition System

ignites a burner with a spark from the igniter electrode inside the Gas CatcherTM

ignition chambe_Yougeneratethe energy forthe spark by pushing the electronic

ignition button.Youwi// hear it clicking.

WARNING: Check hose before each use of barbecue for

nicks, cracking, abrasions or cuts. If the hose is found to

be damaged in any way, do not use the barbecue. Replace

using only Weber ® authorized replacement hose. Contact

the Customer Service Representative in your area using the

contact information on our web site.

Log onto www.weber.com ®.

A) Open the lid (1).

B) Makesure all burner control knobsare turned off (2). (Pushcontrol knob inand turn

clockwise to ensure that it is in the OFF position.)

WARNING: The burner control knobs must be in the OFF

position before turning on the LP cylinder valve. If they are

not in the OFF position, when you turn on the LP cylinder

valve, the "excess gas flow control" feature will activate,

limiting the flow of gas from the LP cylinder. If this should

occur, turn OFF the LP cylinder valve and burner control

knobs. Start over.

DANGER

When the "excess gas flow control" feature is activated,

a small amount of gas is still flowing to the burners. After

turning off the LP cylinder valve and burner control knobs,

wait at least five minutes for the gas to clear before attempting

to ight the gril. Failure to do so may result in an explosive

flare-up, which can cause serious bodly injury or death.

C) Turn the cylinder on by slowly turning the cylinder valve counterclockwise (3).

z_ WARNING: Do not lean over the open barbecue.

D) Push control knob in and turn to START/HI (4).

E) Push and hold the electronic ignition button.You will hear it clicking (5).

F) Check that the burner is lit by looking through the cooking grates. You should see a

flame (6).

WARNING: If the burner does not light in five seconds, stop,

turn the control knob to OFF and wait five minutes to let the

gas clear before you try again or try to light with a match.

G) To light remaining burners follow steps D through R ®

TO EXTINGUISH

Push in and turn each burner control knob clockwise to the OFF position.Turn gas

supply off at the source. ®

ARRETE

÷ + + +

OFF START/HI MEDIUM LOW

ELECTRONIC

iGNiTER

The grill illustrated may

have slight differences

than the model purchased.

[] %

MAIN BURNER MANUAL IGNITION

_ DANGER

Failure to open the lid while igniting the barbecue's burners,

or not waiting five minutes to allow the gas to clear if the

barbecue does not light, may result in an explosive flare-up

which can cause serious bodily injury or death.

A) Open the lid (1).

B) Make sure all burner control knobs are turned off (2). (Push control knob in and turn

clockwise to ensure that it is in the OFF position.)

WARNING: The burner control knobs must be in the OFF

position before turning on the LP cylinder valve. If they are

not in the OFF position, when you turn on the LP cylinder

valve, the "excess gas flow control" feature will activate,

limiting the flow of gas from the LP cylinder. If this should

occur, turn off the LP cylinder valve and burner control

knobs. Start over.

DANGER

When the "excess gas flow control" feature is activated,

a small amount of gas is still flowing to the burners. After

turning off the cylinder and burner control knobs, wait at least

five minutes for the gas to clear before attempting to light the

barbecue. Failure to do so may result in an explosive flare-up,

which can cause serious bodily injury or death.

C) Turn the cylinder on by slowly turning the cylinder valve counterclockwise (3).

D) Put match in the match holder and strike match.

E) Insert match holder with lit match down through cooking grates and Flavorizer _ bars

to ignite the selected burner (4).

z_ WARNING: Do not lean over open barbecue.

F) Push control knob in and turn to START/HI (5).

G) Check that the burner is lit by looking through the cooking grates. You should see a

flame (6).

WARNING: If the burner does not light in five seconds, stop,

turn the control knob to OFF and wait five minutes to let the

gas clear before you try again or try to light with a match.

H) To light remaining burners follow steps D through G.

TO EXTINGUISH

Push in and turn each burner control knob clockwise to the OFF position.Turn gas

supply off at the source. ®

The grill illustrated may

have slight differences

than the model purchased.

o Always preheat the grill before cooking. Set all burners on HI heat and close lid; heat

for 10 minutes, or until thermometer registers 5000-550 ° F (260°-288°C).

Sear meats and cook with the lid down for perfectly grilled food every time.

Grilling times in recipes are based on 70°F (20°C) weather and little or no wind. Allow

more cooking time on cold or windy days, or at higher altitudes. Allow less cooking

time in extremely hot weather.

Grilling times can vary because of the weather, orthe amount, size and shape of the

food being grilled.

The temperature of your gas grill may run hotter than normal for the first few uses.

Grilling conditions may require the adjustment of the burner controls to attain the

correct cooking temperatures.

In general, large pieces of meat will require more cooking time per pound than small

pieces of meat. Foods on a crowded cooking grate will require more cooking time

than just a few foods. Foods grilled in containers, such as baked beans, will require

more time if grilled in a deep casserole rather than a shallow baking pan.

Trim excess fat from steaks, chops and roasts, leaving no more than a scant _Ainch

(6.4mm) of fat. Less fat makes cleanup easier, and is a virtual guarantee against

unwanted flare-ups.

Foods placed on the cooking grate directly above burners may require turning or

moving to a less hot area.

Use tongs rather than a fork for turning and handling meats to avoid losing natural

juices. Use two spatulas for handling large whole fish.

If an unwanted flare-up should occur, turn all burners off and move food to another

area of the cooking grate. Any flames will quickly subside. After flames subside, relight

the grill. NEVER USE WATER TO EXTINGUISH FLAMES ON A GAS GRILL.

Some foods, such as a casserole or thin fish fillets, will require a container for grilling.

Disposable foil pans are very convenient, but any metal pan with ovenproof handles

can also be used.

Always be sure the slide out grease tray and catch pan are clean and free from debris.

Do not line the slide out grease tray with foil. This could prevent the grease from

flowing into the catch pan.

Using a timer will help to alert you when "well-done" is about to become "over-

done."

Note: If grill looses heat while cooking refer to the troubleshooting section of this

manual.

z:_ WARNING: Do not move the Weber _ gas barbecue when

operating or while barbecue is hot.

You can adjust the individual burners as desired.The control settings are OFF,

START/HI, MEDIUM, or LOW.

FLAVORIZER®SYSTEM

When meat juices drip from the food onto the specially angled Flavorizer ¢ bars,

they create smoke that gives foods an irresistible barbecued flavor. Thanks to the

unique design of the burners, Flavorizer ¢ bars and the flexible temperature controls,

uncontrolled flare-ups are virtually eliminated, because YOU control the flames. Because

of the special design of the Flavorizer ¢ bars and burners, excess fats are directed

through the slide out grease tray into the grease catch pan.

ARR_TI_

APAGADO

+ ÷ ÷ ÷

OFF START/Hi MEDIUM LOW

Note: The temperature inside your cookbox for the first few uses, while surfaces are still

very reflective, may be hotter than those shown in your cookbook. Cooking conditions,

such as wind and weather, may require the adjustment of the burner controls to obtain

the correct cooking temperatures.

if burners go out during cooking, turn off all burners and wait five minutes before

relighting. ®

PREHEATING

Your Weber ¢ gas barbecue is an energy-efficient appliance. It operates at an economical

low BTU rate. Preheating the grill before grilling is important. Light your grill according

to the instructions in this Owner's Manual. To preheat: after lighting turn all burners to

START/HI, close the lid, and heat until the temperature reaches between 500° and 550°

F (260 ° and 290 ° C), the recommended broiling temperature. This will take 10 to 15

minutes depending on conditions such as air temperature and wind.

COVERED COOKING

All grilling is done with the lid down to provide uniform, evenly circulated heat. With the

lid closed, the gas grill cooks much like a convection oven.The thermometer in the lid

indicates the cooking temperature inside the grill. All preheating and grilling is done with

the lid down. No peeking -- heat is lost every time you lift the lid.

DRIPPINGS AND GREASE

The Flavorizer _ bars are designed to "smoke" the correct amount of drippings for

flavorful cooking. Excess drippings and grease will accumulate in the catch pan under

the slide out grease tray. Disposable foil drip pans are available that fit the catch pan.

z:_ WARNING: Check the slide out grease tray and catch pan

for grease build=up before each use. Remove excess grease

to avoid a grease fire in the slide out grease tray.

PROBLEM SOLUTION

Burners burn with a yellow or orange flame, in Clean Spider/insect screens. Refer to 'ANNUAL

conjunction with the smelm of gas. MAINTENANCE'.'

Symptoms:

Burners do not ignite. -or- Burners have a small

flickering flame in the HI position. -or-

Barbecue temperature only reaches 250 ° to 300 ° in

the HI position.

Burner does not light, or flame is low in HI position.

Burner does not ignite when you push the igniter

button.

Experiencing flare-ups:

CAUTION: Do not line the slide out

grease tray with aluminum foil.

CHECK

Inspect Spider/Insect screens for possible obstructions.

(Blockage of holes.)

The excess flow safety device, which is part of the

barbecue to cylinder connection, may have activated.

Is LP fuel low or empty?

is fuel hose bent or kinked?

Be sure that there is gas flow to the burners by

attempting to match light your burners. Refer to "MAIN

BURNER MANUAL IGNITION'.'

Is there a fresh battery installed?

To reset the excess flow safety device turn all burner

control knobs and the cylinder valve off. Disconnect

the regulator from the cylinder. Turn burner control

knobs to Hi. Wait at least 1 minute.Turn burner control

knobs to OFF. Reconnect the regulator to the cylinder.

Turn cylinder valve on slowly. Refer to "MAIN BURNER

IGNITION':

Refill LP cylinder.

Straighten fuel hose.

if match lighting is successful, the problem lies in the

ignition system. Refer to "ELECTRONIC IGNITION

SYSTEM OPERATIONS'.'

Verify that the battery is in good condition and installed

correctly. Refer to "ELECTRONIC IGNITER INSPECTION".

Are the wires connected properly to the ignitior module? Be sure that wires are correctly inserted into terminals on

ignition box. Refer to "ELECTRONIC IGNITION SYSTEM

OPERATIONS'.'

Remove plastic wrapping.is there plastic wrapping around the new battery?

Are you preheating barbecue in the prescribed manner?

Are the cooking grates, heat deflectors, and Flavorize¢ _

bars heavily coated with burned-on grease?

is the slide out grease tray dirty and not allowing grease

to flow into catch pan?

Are burners clean?

All burners on HI for 10 to 15 minutes for preheating.

Clean thoroughly. Refer to "CLEANING':

Clean slide out grease tray.

Burner flame pattern is erratic. Flame is low when Clean burners. Refer to "MAINTENANCE'.'

burner is on HI. Flames do not run the whole length

of the burner tube.

Inside of lid appears to be "peeling." (Resembmes The inside of the lid is porcelain enamel or stainless Clean thoroughly. Refer to "CLEANING'.'

paint peeling.) steel, and is not painted. It cannot "peel': What you are

seeing is baked on grease that has turned to carbon and

is flaking off.

THIS IS NOT A DEFECT.

Cabinet doors are not aligned. Check the adjustment pin on the bottom of each door. Loosen adjustment nut/s. Slide dooris until aligned.

Tighten nut.

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our

web site. Log onto www.weber.com _.

CLEANING

z_ WARNING: Turn your Weber _ gas barbecue off and wait for

it to cool before cleaning.

Z_ CAUTION: Do not clean your Flavorizer _ bars or cooking

grates in a self-cleaning oven.

Outside surfaces - Use a warm soapy water solution to clean, then rinse with water.

z_ CAUTION: Do not use oven cleaner, abrasive cleansers

(kitchen cleansers), cleaners that contain citrus products, or

abrasive cleaning pads on barbecue or cart surfaces.

Smide-out grease tray - Remove excess grease, wash with warm soapy water, then

rinse.

z_ CAUTION: Do not line the slide=out grease tray with

aluminum foil.

Fmavorizer ¢ bars and cooking grates - Clean with a suitable stainless steel bristle

brush. As needed, remove from grill and wash with warm soapy water, then rinse with

water.

For availabimity of replacement cooking grates and Flavorizer ¢ bars, contact the

Customer Service Representative in your area using the contact information on

our website. Log onto www.weber.com ®.

Catch pan - Disposable foil trays are available, or you can line the catch pan with

aluminum foil. To clean the catch pan, wash with warm soapy water, then rinse.

Thermometer - Wipe with warm soapy water; clean with plastic scrub ball.

Cookbox - Brush any debris off of burner tubes. DO NOT ENLARGE BURNER PORTS

(OPENINGS). Wash inside of cookbox with warm soapy water and a water rinse.

mnside mid- While lid is warm, wipe inside with paper towel to prevent grease build-up.

Flaking built-up grease resembles paint flakes.

Stainmess steem surfaces - Wash with a soft cloth and a soap and water solution. Be

careful to scrub with the grain direction of the stainless steel.

Do not use cmeaners that contain acid, mineram spirits or xymene. Rinse well after

cleaning.

Preserve your stainless steem- Your grill or its cabinet, lid, and control panel may be

made from stainless steel.To keep the stainless steel looking its best is a simple matter.

Clean it with soap and water, rinse with clear water, and wipe dry. For stubborn particles,

a non-metallic brush can be used.

z_ IMPORTANT: Do not use a wire brush or abrasive cleaners

on the stainless steel surfaces of your grill as this will cause

scratches.

z_ IMPORTANT: When cleaning surfaces be sure to rub/wipe

in the direction of the grain to preserve the look of your

stainless steel.

WEBER ®SPIDER/INSECT SCREENS

Your Weber _ gas barbecue, as well as any outdoor gas appliance, is a target for spiders

and other insects. They can nest in the venturi section (1) of the burner tubes. This

blocks the normal gas flow, and can cause the gas to flow back out of the combustion air

opening. This could result in a fire in and around the combustion air openings, under the

control panel, causing serious damage to your barbecue.

The burner tube combustion air opening is fitted with a stainless steel screen (2) to

prevent spiders and other insects access to the burner tubes through the combustion air

openings.

We recommend that you inspect the Spider/mnsect screens at meast once a year.

(Refer to "ANNUAL MAmNTENANCE') Also inspect and clean the the Spider/mnsect

screens if any of the fommowing symptoms shoumd ever occur:

A) The smell of gas in conjunction with the burner flames appearing yellow and lazy.

B) Barbecue does not reach temperature.

C) Barbecue heats unevenly.

D) One or more of the burners do not ignite.

DANGER

Failure to correct the above mentioned symptoms may result

in a fire, which can cause serious bodily injury or death, and

cause damage to property. _,

BURNER TUBES CLEANING OR REPLACEMENT

You will need: Phillips screwdriver and flathead screwdriver.

A) Your Weber ¢ gas barbecue must be OFF and cool.

B) Turn gas OFF at source.

C) Remove cookbox components - warming rack, grates and Flavorizer ¢ bars. (Heat

deflectors do not need to be removed.)

Control Panel Removal

To remove control panel:

A) Remove control knobs, igniter button, igniter retention nut, and battery (1).

B) Remove screws from wind deflector (2) located underneath the control panel with a

Phillips screwdriver.

C) Tilt end of wind deflector down and slide away to remove (3).

D) Remove igniter module from control panel (4) and remove all four wires from

module.

E) Remove screws from underside of control panel with Phillips screwdriver (5).

F) Lift control panel up slightly, tilt up front edge and gently lift up and away (6).

Burner Tube Removal

To remove burner tube(s):

A) Remove igniter wire(s) from igniter clip(s) (7).

B) Remove screw that holds burner tube to the cookbox using a flathead screwdriver (8).

C) Pull burner tube assembly (this includes igniter) up and out of cookbox (9).

Note. 310/320 units will have an additional grounding wire attached to the center

burner tube (10).

Burner Tube Cleaning

To clean the burner tube(s):

A) Look inside each burner with a flashlight (11).

B) Clean the inside of the burners with a wire (12) (a straightened-out coat hanger will

work).

C) Check and clean the air shutter opening at the ends of the burners. Check and

clean the valve orifices at the base of the valves. Use a steel bristle brush to clean

outside of burners (13).This is to make sure all the burner ports are fully open.

z_ CAUTION: Do not enlarge the burner ports when cleaning.

Burner Tube Reinstallation

To reinstall burner tubes:

A) Slide burner tube and igniter wire through hole in cookbox (14). Refer to

"ELECTRONIC IGNITION SYSTEM OPERATIONS" for proper burner position.

B) Align burner tube with valve.

z_ CAUTION: The burner openings (15) must be positioned

properly over the valve orifices (16).

C) Re-install screw that holds the burner tube to the cookbox using a flathead

screwdriver. Burner tube may seem loose (17), when screw is snug. This is normal.

D) Route wires back through igniter clips. Refer back to figure (7).

CAUTION: All wires must be properly routed through wire

clips.

E) Attach wires to module, following the numerical/color coding (18). Refer to

"ELECTRONIC IGNITION SYSTEM OPERATIONS" for proper attachment of wires.

z_ WARNING: After reinstalling the gas lines, they should be

leak checked with a soap and water solution before using

the barbecue. (Refer to "CHECK FOR GAS LEAKS".)

z_ WARNING: Make sure that all parts are assembled and

hardware is fully tightened before operating the grill. Your

actions, if you fail to follow this Product Warning, may

cause a fire, an explosion, or structural failure resulting

in serious personal injury or death as well as damage to

property.

La page charge ...

Weber E310LP-2011 Le manuel du propriétaire

Marque: Weber

Modèle: E310LP-2011

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Weber E310LP-2011 Owner's manual
español: Weber E310LP-2011 El manual del propietario

Weber E310LP-2011 Le manuel du propriétaire

Weber E310LP-2011 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents