Scholtes CL 1 Instructions For Use Manual

NA

Instructions for use

English,1 Espanol, 53Français, 27

FR

NA

SP

Coffee center

Index

Installation 4

Positioning

Built-in installation

Ventilation

Centring and fixing

Electrical connection

Installing the power cable

Rating plate

Description of the appliance 6

Overall view

Control panel

Starting and using 7

The first time you switch on

Priming the water circuit

Regulating water hardness

Water filter

Installing the Water filter

Additional information for correct use of the Water filter

Grinding regulation

Brewing 10

Crema control

Regulating the quantity of coffee per cup

Brewing coffee (1 cup)

Brewing coffee (2 cups)

Dispensing hot water

Brewing steaming/cappuccino

Maintenance and care 12

General cleaning

Descaling

Interrupting the descaling cycle

Programming 15

MENU command

Changing individual functions

Programmable functions

Factory settings

Display messages 23

Problems - causes - solutions 24

Precautions and recommendations 25

Statements of warranties 26

CL 1

2

NA

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce

the risk of fire, electric shock, and/or injury to persons, including the following:

1 Read all instructions and information in this instruction book and any other literature included

in this carton referring to this product before operating or using this appliance.

2 Do not touch hot surfaces. Use handles or knobs.

3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or

appliance in water or other liquid.

4 Close supervision is necessary when any appliance is used by or near children.

5 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or

taking off parts, and before cleaning the appliance.

6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions

or has been damaged in any way. Return appliance to the nearest authorized service centre

for examination, repair or adjustment.

7 The use of accessory attachments not recommended by the appliance manufacturer may

result in fire, electric shock or personal injury.

8 Do not use outdoors.

9 Do not let cord hang over edge of table or counter, or touch hot surfaces.

10 Do not place on or near a hot gas or electric burner, or in a heated oven.

11 Always turn appliance “OFF”, then plug cord into the wall outlet. To disconnect, turn switch to

“OFF”, then remove plug from wall outlet.

12 Do not use appliance for other then intended household use.

13 Use extreme caution when using hot steam.

SAVE THESE INSTRUCTIONS

NA

3

CAUTION

This appliance is for household use. Any servicing, other than cleaning and user maintenance,

should be performed by an authorized service centre. Do not immerse base in water. To reduce

the risk of fire or electric shock, do not disassemble the base. There are no user serviceable parts

inside. Repair should be done by authorized service personnel only.

1 Check voltage to be sure that the voltage indicated on the nameplate agrees with your

voltage.

2 Never use warm or hot water to fill the water tank. Use cold water only.

3 Keep your hands and the cord away from hot parts of the appliance during operation.

4 Never clean with scouring powders or hard implements. Simply use a soft cloth dampened

with water.

5 To avoid your coffee maker scaling up, use purified or bottled water.

INSTRUCTIONS FOR THE POWER SUPPLY

CORD

A A short power-supply cord is provided to reduce risks of getting tangled up or tripping over

a longer cord.

B Longer extension cords are available and may be used if care is exercised in their use.

C If a long extension cord is used:

1 the marked electrical rating of the extension cord should be at least as great as the electrical

rating of the appliance.

2 if the appliance is of the grounded type, the extension cord should be a grounding type

3 the cable does not hang from the table to avoid the risk of getting caught up in it.

4

NA

Installation

! Keep this booklet for consultation at any time. In the

event of sale, transfer of the machine or of the owner

ensure that the booklet is kept with the machine so that

the new owner is informed of the operating instructions

and warnings.

! Read all instructions carefully. They contain important

information regarding installation, operation and safety.

Positioning

! Packaging is not a toy for children and should

be disposed of in accordance with regulations for

separated waste collection (see Precautions and

recommendations).

! Installation must be carried out in compliance with

these instructions by professionally qualified personnel.

Incorrect installation may cause damage to persons,

animals and/or objects.

Built-in installation

To ensure the correct functioning of the appliance, the

cabinet must have the right characteristics:

• the panels next to the coffee machine must be in

heat-resistant material;

• veneered wood cabinets should be joined using

glues resistant to 100°C/212°F and must be steam-

resistant;

• for all installations of built-in coffee machines

cabinets should have the following dimensions:

! Once the appliance has been encased, there must

be no contact possible with electrical parts. Declared

consumption values shown on the rating plate are

measured on the basis of this type of installation.

Ventilation

To ensure good ventilation, remove the rear panel of the

cabinet.

It is recommended to install the coffee machine so that

it is resting on a continuous surface with an opening of

at least 1¾” x 21¼” (45 x 540 mm) in the base.

Centring and fixing

To centre the coffee machine, position the shims

beneath the holes in the outer structure of the machine.

! All shims must be attached so that they ensure perfect

stability of the machine.

To attach the shims to the cabinet proceed as follows:

• remove the drip tray

from the machine;

• fasten the 2 wood

screws in the 2 holes

located to the rear of the

base.

• remove the lower

plastic protection;

NA

5

Rating plate

• Nominal voltage

See plate on the appliance

• Power rating

See plate on the appliance

• Power supply

See plate on the appliance

• Shell material

Metal

• Dimensions (w x h x d)

595 x 460 x 320(mm)

Faceplate - 23.43” x 18.11” x 0.79”

Body - 21.26” x 18.11” x 11.89”

• Weight

23 kg / 51 lbs

• Cable length

1200 mm / 47¼”

• Control panel

Piezoelectric

• Water tank

Removable

• Water tank

1.75 liters / 59.17 fluid onces

• Coffee bean hopper capacity

300 g / 10 onces coffee beans

• Pump pressure

15 bars / 1500 KPa

• Boiler

2 - Stainless Steel - Aluminium

• Safety devices

Boiler pressure safety valve

Safety thermostat

Subject to engineering and manufacturing changes

due to technological developments.

The machine conforms to the European Directive

89/336/EEC (Italian Legislative Decree 476 dated

04/12/92) concerning electromagnetic compatibility.

! All protective parts must be attached so that they

cannot be removed without the aid of a tool.

Next replace the protection and the drip tray.

Electrical connection

! Coffee machines with three-pole power cable are

regulated for alternating current, with voltage and

frequency shown on the rating plate attached to the

appliance.

! The installer is responsible for checking the correct

connection of components and observing safety

regulations.

Before connecting make sure that:

• the socket is earthed and is compliant with statutory

regulations:

• the socket is able to withstand the maximum power

load of the machine, shown on the rating plate;

• the supply voltage is within the values shown on the

rating plate;

• the socket is compatible with the appliance’s plug.

Otherwise replace the plug or the socket; do not use

extension leads or adaptors.

! Once the appliance is installed, the electric cable and

socket must be easy to reach.

! The power cable must not be subject to coiling or

compression.

! The cable must be checked regularly and replaced

only by authorised technicians.

! The company accepts no responsibility for non-

compliance with these regulations.

Installing the power cable

• Put the plug in the

tray socket on the rear

of the machine

• Connect the power

cable to the mains

• Put the plug in the

power socket.

The position of the

power cable must be

such that no section of it is above room temperature

by more than 50°C/122°F.

6

NA

Description of the

appliance



Overall view

Control panel

Water tank

Main switch

Coffee bean container

Front control panel

Crema control

Hot water/steam spout

Drip tray

Adjustable-height brew unit

Tray

Grill

Brewing group

Grind regulator

Select DOUBLE COFFEE key

Select LONG COFFEE key

Select REGULAR COFFEE key

Select ESPRESSO key

Select HOT WATER key

Select STEAM key

SELECT/CONFIRM

Key

PAGE SCROLL

key

PROGRAMMING/EXIT

selection key

DESCALING

key

Display

NA

7

Rinse and fill the

tank with fresh drinking

water, always up to the

max level.

Close the lid and

replace the tank in

position.

! Attention you will be

notified on the display

to fill the water tank.

This will happen already

when the tank is only half empty caused by the use of

the water filter which soften your water.

! Always use fresh, non-sparkling water to fill the tank.

Hot water or any other liquid may damage the tank

and/or the machine. Do not switch the machine on

without water: make sure that the tank is fully filled

with water.

The main switch is in

the “O” position. To

switch on, press the key

in the “I” position.

Close the front panel

by pressing firmly in the

centre. The machine

begins to heat up and the display shows:

RINSING

WARMING UP...

When the right temperature is reached, the machine

goes through a rinsing cycle.

RINSING

The machine dispenses water from the brew unit as it

rinses the internal circuits.

After rinsing, the machine returns to normal operating

conditions. The display shows:

SELECT PRODUCT

READY FOR USE

! To disable the rinse cycle, see the paragraph on

programming the machine.

Starting and using

! Before starting the machine make sure the containers

are filled with the amount described in the manual.

Prime the circuit immediately to prevent damage to the

machine.

! After starting the machine, regulate water hardness.

That will allow you to keep your machine in perfect

order (see Programming).

The first time you switch on

1. Open the front panel

by pressing firmly in the

center.

2. Remove the bean

container.

(to your convenience,

you can take out

complete container and

fill whenever you want

or even changhe the

container with another

one which is filled, for

example, with decaf

coffee).

3. Pour coffee beans

into the container being

careful not to add too

many.

Close the lid and repla-

ce the container inside

the machine.

4. Remove the water

tank fully from the

machine.

8

NA

Priming the water circuit

! Before starting the machine after long periods of

inactivity, it is essential to prime the machine circuit.

Moreover the circuit must be primed every time the

following is displayed:

VENTILATE

1. To prime the circuit,

direct the steam spout

over the drip tray.

Place a cup or suitable

container below the

steam spout and press

the

key.

2. Wait until the water runs smoothly out of the steam

spout.

To interrupt, press the

key.

After the above operations have been completed the

machine is ready for use.

To dispense coffee, hot water or steam and for proper

use of the machine, carefully follow the instructions that

are provided.

Water filter

All Scholtes non-plumbed coffee centers are equipped

with the water filter.

The water filter purifies the water used in the

preparation of coffee.

Its properties reduce the hardness of water and remove

the unpleasant taste of chlorine.

The water filter may be installed at any time.

Installing the water filter

1. Open the front panel

and remove the water

tank.

Empty the tank of any

water.

2. Remove the filter

packaging and set the

calendar to the current

month.

! Refer to the notes for

using the filter below.

3. Insert the filter into the

tank. The reference mark

and the groove should

coincide. Press down

completely.

Fill up the tank with fresh

drinking water.

After 30 minutes, di-

spense all the water in

the tank into a container.

Afterwards fill the tank

again with water and

replace the tank in the

machine. Close the front

panel.

! The machine is already

programmed for use with the filter (see programming).

The machine informs the user when it is time to replace

the filter.

! The water filter must always be removed before

running the descaling cycle.

Regulating water hardness

Regulate the machine to the right degree of water hard-

ness that you will use.

According to this setting, the machine advises when it is

necessary to run a descaling cycle.

Read the sections on “Water hardness” in “Program-

ming” to regulate hardness.

NA

9

Grinding regulation

! Take care when rotating the knob that regulates

grinding, which is located above the brewing group. Do

not put ground and/or freeze-dried coffee in the bean

container.

! Do not put any material other than coffee beans in

the container.

Switch off at the mains before carrying out any type of

operation inside the machine.

The quality and flavour of coffee depend on the

grinding level, as well as the blend used.

The machine has a knob to regulate the coffee

grinding.

To regulate the grinding,

turn the knob one

setting at a time. The

figures indicate the

fineness of the grind.

The manufacturer

configures each

appliance on an

intermediate grinding

setting. If the grind is

too fine, rotate the knob to a higher setting; if the grind

is too coarse, turn the knob to a lower setting.

The variation in grind will only be seen after one or two

coffees have been brewed.

Use coffee bean blends for espresso machines. Try

not to use high grinding settings (e.g. 1/10). Use

different coffee blends for these settings. Keep the

coffee in a fresh place in a sealed, airtight container.

Grinding must only be regulated if coffee is not brewed

properly:

• if it is brewed too fast, this means that the grind is

too coarse; turn the knob to a lower setting;

• if it is brewed in drips and/or intermittently, this

means that the grind is too fine; turn the knob to a

higher setting.

We reccomend to replace the old filter with a new one

after every descaling cycle.

Additional information for correct use of

the water filter.

For correct use of the water filter (where installed),

here are a number of recommendations:

1. Store the water filter in a cool place away from the

sun, at a temperature of between +5°C/41°F and

+40°C/104°F;

2. Use in areas with temperature no higher than

60°C/140°F;

3. It is advisable to wash the water filter if the machine

has been inactive for 3 days or more;

4. Replace filter if the machine has been inactive for

20 days or more;

5. To preserve a filter that has already been opened,

place in a plastic airtight bag and store in the

refrigerator; do not store in freezer, as this will alter

the properties of the filter;

6. Before using the filter, place in water in the tank for

30 minutes;

7. Once removed from its package, do not store filter

in the open air;

8. The filter must be replaced 90 days after it has been

removed from its package.

9. To ensure proper functioning of the product, we

raccomend to replace the old filter witha new one

after every a descaling cycle.

10

NA

Crema control

With this knob, you can regulate the amount of water

pressure so that each cup is brewed to the right

strenght and consistency, from a mild, American style

coffee, to a robust Italian

espresso

! Regulation can even be

done while the coffee is

brewing.

Turn the knob to regulate.

Rotate knob:

• left for crème café;

• to the center for espresso;

• right for a strong coffee.

Regulating the quantity of coffee per cup

The machine is programmed to brew 3 kinds of coffee:

espresso coffee with the

key,

regular coffee with the

key;

long coffee with the

key.

To adjust the

programmed values to

the size of the cup, place

the cup beneath the

brew unit.

Press the

key

and using the

key scroll through the

functions until you get to:

PROGR. COFFEE LENG.*

PROGR. WATER AMOUNT

Press the key; the display shows:

SELECT PRODUCT

PROGRAMM. COFFEE

press the key to brew the required type of coffee

(

, or ); this is shown on the display (e.g.):

1 SMALL COFFEE

PROGRAMM. COFFEE

Wait for the cup to fill with the required amount. Press

the same key again.

In this way the machine is programmed to brew the

quantity of coffee you require.

Brewing coffee (1 cup)

! Before brewing coffee, make sure the water tank and

the coffee tank are full and that the display shows:

SELECT PRODUCT

READY FOR USE

Place 1 cup beneath the

brew unit spouts.

You can adjust the height

of the brew unit to your

cups by shifting it up or

down manually.

To brew the coffee press the coffee brewing key (

,

or ). This is shown on the display (e.g.):

1 SMALL COFFEE

DISPENSING

In this operating mode the machine automatically grinds

and measures out the right amount of coffee.

Next the brew cycle is started.

1 SMALL COFFEE

PREBREWING...

After the prebrewing cycle, the coffee begins to come

out of the brew unit spout.

The display will show:

1 SMALL COFFEE

DISPENSING

Dispensing stops automatically when the set level is

reached.

! It is possible to interrupt dispensing coffee by pressing

the key (

, or ).

Brewing

NA

11

Brewing coffee (2 cups)

! Before brewing coffee, make sure the water tank and

the coffee tank are full and that the display shows:

SELECT PRODUCT

READY FOR USE

Place 2 cups beneath

the brew unit spouts.

You can adjust the

height of the brew unit

to your cups by shifting

it up or down manually.

To brew the coffee, press first the

key, and then

the coffee brewing key (

, or ). This is shown

on the display, e.g.:

2 SMALL COFFEES

DISPENSING

In this operating mode the machine automatically

grinds and measures out the right amount of coffee.

! The preparation of two coffees requires two grinding

cycles and two separate brew cycles. These are

handled automatically by the machine.

Next the brew cycle is started.

2 SMALL COFFEES

PREBREWING...

After the prebrewing cycle, the coffee begins to come

out of the brew unit spout.

The display will show:

2 SMALL COFFEES

DISPENSING

Dispensing stops automatically when the set level is

reached.

! It is possible to interrupt dispensing coffee by

pressing (

, or ) key; If the first coffee is

interrupted, the second will not be dispensed.

Dispensing hot water

! At the start, short spurts of hot water may be

dispensed. Danger of scalding. The hot water spout

can reach high temperatures. Do not touch it with

bare hands.

Before dispensing water, make sure the following is

shown on the display:

SELECT PRODUCT

READY FOR USE

When the machine is

ready to brew coffee,

proceed as follows:

1. Place a cup and/or a

container below the hot

water/steam spout.

2.Press the

key; the display shows:

HOT WATER

! A preset amount of water is dispensed. This may be

modified in the “PROGR. WATER AMOUNT” menu

described in the chapter on “Programming”.

To stop dispensing hot water, press the

key again.

The machine returns to normal operating mode.

Brewing steaming/cappuccino

Steam can be used to froth milk for cappuccino and

also to heat beverages.

! Danger of scalding! At the start, short spurts of hot

water may be dispensed. The brewing spout can reach

high temperatures: Do not touch it with bare hands.

12

NA

1. With the machine

ready to brew coffee,

place a cup and/or a

container below the hot

water/steam spout.

2. Press the

key to

discharge any water left

in the steam spout; in a

short time, only steam

will come out of the

spout.

The display shows:

STEAM

3. Press the key to stop dispensing steam.

4. Fill 1/3 of the container you wish to use to prepare

the cappuccino with cold milk.

! Use cold milk and a cold cup for better results

when preparing cappuccino.

5. Immerse the steam

spout in the milk to be

heated and press the

key. Move the container

gently up and down for

uniform foam formation.

! Steam is dispensed for

a preset amount of time.

This may be modified

in the “PROGRAM

STEAM TIME” menu described in the chapter on

“Programming”.

6. Press the

again to stop dispensing steam.

! The same system can be used to heat other

beverages.

! After this operation,

clean the steam spout

with a wet cloth.

Maintenance and care

General cleaning

! Maintenance and cleaning operations can only be

carried out when the machine is cold and disconnected

from the power supply.

• Do not immerse the machine in water or place any of

its parts in a dishwasher.

• Do not use sharp objects or harsh chemical products

(solvents) for cleaning.

• Do not dry the machine and/or its components in a

microwave and/or conventional oven.

• Clean the water tank

on a daily basis and

change the water.

• Remove and clean

the filter in the tank.

• Use a soft cloth

moistened with water to

clean the appliance.

• Clean the dispensing

outlet and the brew

group.

• We recommend

emptying and cleaning

the drip tray and the

dregs drawer on a daily

basis. To do this, extract

the drip tray then empty

and clean all parts.

• The brew unit may be

removed for cleaning:

1. Lower the brew unit

spouts

2. Grasp the brew unit as

shown and extract it from

its seat.

3. Wash the whole unit in

hot water.

NA

13

! Use the appropriate protection to open the service

door when the brew unit is assembled.

1. Remove the

protection located in

the lower part of the

machine.

• Wash the two steel

filters of all coffee

residues.

• The brew group

must be cleaned only

with warm water and

no detergents. Wash

all parts and dry

thoroughly.

• Thoroughly clean

the inside compartment of the machine.

• Before inserting the

brew group, make sure

that all components are

correctly positioned;

hook in top position and

lever in bottom position.

2. Install the protection

in the brew unit pushing

it inward.

3. Open the service

door leaving the

protection in the brew

unit.

! In the protection there

is a sponge which

collects the coffee

residues. When the

operations have been

completed, wash the sponge under running water.

! Once finished, remove the protection and restore the

brew unit correctly to its position.

The brew group must be cleaned every time the coffee

bean container is filled and at least once a week.

• Switch off the machine by pressing the main switch

to “O”.

• Remove the drip

tray and the dregs

drawer. Open the

service door.

• Remove the brew

group by the handle

and press the key

marked “PUSH”.

• Press the “PUSH”

button firmly to move

the lever back to its

initial position.

• Press the group in

the indicated point to

move the lever back to

its correct position.

• Take the handle and

return the brew group

to the compartment

clicking it into place.

Close the door.

• Place the dregs drawer and the grill in the drip tray

before inserting into the machine.

! For perfect efficiency of the brew group, a

maintenance kit is available.

We recommend to use the maintenance kit every 12

months of use.

! For perfect efficiency of the brew group, a

maintenance kit is available from Scholtes outlets.

14

NA

Descaling

Scale normally forms with use of the appliance.

Descaling is necessary every 3 - 4 months (depending

on the water hardness and the use of the water filter)

when there is a reduction in water flow or when the

machine displays the following message:

READY FOR USE

DECALCIFY

! If you want to descale the machine yourself, you can

use a non-toxic and/or non-harmful descaling product

for coffee machines, commonly available in the shops.

Scholtes descaling product is highly recommended.

! Never use vinegar as a descaler.

! Remove the water filter before descaling (where

installed).

Follow the instructions for descaling:

1. Mix the descaling

product with water

following the instructions

on the product package,

and fill the tank with water.

2. Turn on the machine

at the main switch.

3. Press the

key to select the function. The display

shows:

DESCALING

NO

4. Using the keys, select:

DESCALING

YES

5. Direct the steam spout

towards the drip tray.

6. Place a suitably sized

container below the

steam spout and press

the

key.

The machine will start an automatic descaling cycle

with pauses programmed by the manufacturer and

automatically managed by the machine.

The display will show:

MACHINE IS DESCALING

7. At the end of the cycle, dispensing of the descaling

solution will stop and the display will show:

RINSE MACHINE

FILL WATERTANK

8. Rinse the water tank

thoroughly and fill it with

fresh drinking water.

Replace the tank and

close the front panel.

The display will show:

RINSE MACHINE

PRESS WATER KEY

9. Place a suitably sized

container below the

steam spout and press

the

key.

Rinsing of the machine

circuits begins and the

display will show:

MACHINE IS RINSING

10. When the rinse cycle is complete, the display will

show:

RINSING FINISHED

PRESS WATER KEY

11. Fill the water tank, press the key, reprime the

circuits and leave the machine to heat up.

! If you are using a product other than the

recommended one it is important to follow the

manufacturer’s instructions shown on the pack of the

descaling product.

Maintenance and care

NA

15

Interrupting the descaling cycle

If the descaling cycle is interrupted by the machine

switching off, it is resumed when the machine is

switched on again.

The descaling cycle may be interrupted by pressing

the

key; the display shows:

MACHINE IS DESCALING

INTERRUPTED

press the key and the descaling cycle resumes. If

the

key and the key are pressed, the display

shows:

DESCAL. INTERRUPTED

EMPTY WATERTANK

Warning! After the operation, empty the water tank of

the descaling solution and wash it with fresh drinking

water. The machine’s circuit must be washed with a

rinse cycle.

Proceed as for a normal rinse cycle as described at

point 8 of the previous chapter.

Setting machine functions

The user can change a number of the machine’s

operating parameters according to personal

preference.

These functions are:

Standby, Rinsing, Language, Contrast, Water

hardness, Water filter, Temperature, Coffee Size,

Quantity of Water, Steam time, Espresso flavour,

Coffee flavour, Long coffee flavour, Pre-brewing,

Counter, Timer, Clock and Washing cycle.

Programming

MENU command

To change operating parameters, enter programming

mode with the

key, when the machine is at rest.

In programming, select the required function and press

the

key. This scrolls you through the functions

available on the machine.

To exit the programming, press the

key.

Changing individual functions

Select the required function by pressing the

key.

Enable the required function with the

key. Scroll

through the variables using the

key. To save

the required variable, press

key.

Note: the

key interrupts programming at any time

without saving changes. This operation is only possible

before pressing the

key.

16

NA

Programmable functions

STANDBY

When the appliance is used very little, it is possible

to select the STANDBY mode. This function reduces

energy costs. Nevertheless, it is recommended to

switch off the appliance at the mains if it is to be out of

service for long periods. The machine reheats in just a

few minutes when reactivated.

Select the function by pressing the

key

STANDBY *

RINSING

and enable with the key. The display shows:

STANDBY

The machine is on but none of its components is active.

To activate the machine press

.

RINSING

Immediately after heating, the appliance automatically

eliminates any water left in the internal ducts to ensure

that only fresh water is used to make coffee.

The function has been enabled by the manufacturer.

To disable the function, press the

key, select this

function:

RINSING *

LANGUAGE

and enable it with the key. The display shows:

RINSING

ON

Now, with the key select

RINSING

OFF

and save the choice using the key.

LANGUAGE

This setting allows you to choose the machine

operating language. Moreover, it allows you to

adjust the parameters of the beverages to the typical

parameters of the country where the machine is used.

This is why some languages are differentiated also by

country. The machine is generally programmed with the

language of the country where it will be sold.

To change the language, use the

key to choose

this function:

LANGUAGE *

CONTRAST

and enable it with the key.

The display shows:

LANGUAGE

ENGLISH

Select the required language by pressing the

key and use the

key to save your choice.

CONTRAST

Regulates display contrast for better viewing.

Use the

key to select this function:

CONTRAST *

WATER HARDNESS

Enable it with the key.

The display shows:

CONTRAST

>¢¢¢¢¢ < 50

Now select the required contrast by pressing the

key and use the

key to save your choice.

Programming

NA

17

WATER HARDNESS

Water hardness varies according to geographical

region. Hence, the machine must be regulated for

the hardness of the water used. This is expressed on

a scale of 1 to 4. The

appliance is already

programmed for

average hardness (3).

To regulate hardness,

briefly dip (1 second)

the strip provided in

water.

Next, shake the strip

gently to eliminate

excess water. After one

minute the test results are visible. Check the number

of squares that have changed colour.

Use the

key to select this function:

WATER HARDNESS *

WATERFILTER

Enable it with the key.

The display shows:

WATER HARDNESS

HARDNESS 3

Select the right hardness using the key (e.g. 2

squares = Hardness 2) and save using the

key.

! Warning: this setting allows the machine to notify

when it is time for descaling treatment.

The display shows:

READY FOR USE

DECALCIFY

WATER FILTER (where installed)

This function provides better management of the

“water filter (where installed), notifying the user when

the filter is to be replaced.

! The function must be enabled when installing the

water filter for the first time.

Use the

key to select this function:

WATERFILTER *

TEMPERATURE

Enable it with the key.

The display shows:

WATERFILTER

OFF

Use the key to select

WATERFILTER

ON

and press the key to confirm.

! The “RESET” must be given whenever a new

cartridge filter is installed.

For this command, use the

key to select the

function:

WATERFILTER

RESET

Enable it with the key.

TEMPERATURE

This function regulates the temperature of the water

for coffee (high, medium and low).

Use the

key to select the function:

TEMPERATURE *

PROGR. COFFEE LENG.

Enable it with the key.

The display shows (e.g.):

TEMPERATURE

MEDIUM

Select the required temperature by pressing the

key and use the key to save your choice.

18

NA

Enable it with the key.

The display shows:

SELECT PRODUCT

PROGRAMM. WATER

Position the container that you want to fill and press .

Water is dispensed from the steam spout and the

display shows:

HOT WATER

PROGRAMM. WATER

When the required amount is reached, press the

key again.

The machine is now programmed.

PROGRAMMING STEAM TIME

This function enables you to regulate how long steam is

dispensed whenever

is pressed.

Use the

key to select the function:

PROGRAM STEAM TIME *

AROMA SMALL COFFEE

Enable it with the key.

The display shows:

SELECT PRODUCT

PROGRAMM. STEAM

Position the container with the drink that you want to

heat and press the

key.

Steam is dispensed from the spout and the display

shows:

STEAM

PROGRAMM. STEAM

When the required amount is reached, press the

key again.

The machine is now programmed.

Programming

PROGRAMMING COFFEE SIZE

This function enables you to regulate the amount of

coffee brewed when the (

, or ) keys are

pressed.

You can program the amount dispensed one key at a

time Continue repeating the procedure described below

to program several keys.

Use the

key to select the function:

PROGR. COFFEE LENG.*

PROGR. WATER AMOUNT

Enable it with the key.

The display shows:

SELECT PRODUCT

PROGRAMM. COFFEE

! In this phase, if the display remains idle for a certain

amount of time, the machine exits the function.

Position the cup that you want to fill.

Press the key to brew the required type of coffee (

,

or ); this is shown on the display (e.g.):

1 SMALL COFFEE

DISPENSING

and then:

1 SMALL COFFEE

PROGRAMM. COFFEE

Wait for the cup to fill with the required amount. Press

the key again.

PROGRAMMING THE QUANTITY OF WATER

This function enables you to regulate the amount of

water that is dispensed whenever

is pressed. You

need just one key to fill your container with the right

amount of water

Use the

key to select the function:

PROGR. WATER AMOUNT*

PROGRAM STEAM TIME

NA

19

AROMA ESPRESSO

This function allows you to program a dosage

(quantity) setting for coffee beans to be ground for

espresso (strong, normal, mild).

Use the

key to select the function:

AROMA SMALL COFFEE *

AROMA COFFEE

Enable it with the key.

The display shows (e.g.):

AROMA SMALL COFFEE

STRONG

Select the required dose by pressing the key

and use the

key to save your choice.

AROMA COFFEE

This function allows you to program a dosage

(quantity) setting for coffee beans to be ground for

coffee (strong, normal, mild).

Use the

key to select the function:

AROMA COFFEE *

AROMA LARGE COFFEE

Enable it with the key.

The display shows (e.g.):

AROMA COFFEE

NORMAL

Select the required dose by pressing the key

and use the

key to save your choice.

AROMA LONG COFFEE

This function allows you to program a dosage

(quantity) setting for coffee beans to be ground for

long coffee (strong, normal, mild).

Use the

key to select the function:

AROMA LARGE COFFEE *

PREBREWING

Enable it with the key.

The display shows (e.g.):

AROMA LARGE COFFEE

STRONG

Select the required dose by pressing the key

and use the

key to save your choice.

PRE-BREWING

The pre-brewing process enhances the aroma of

coffee to give it an excellent taste. This function

moistens the coffee before it is actually brewed.

Use the

key to select the function:

PREBREWING *

TOTAL COFFEES

Enable it with the key.

The display shows (e.g.):

PREBREWING

ON

Use the key to choose whether to disable the

function:

PREBREWING

OFF

or to extend the phase

PREBREWING

LONG

to enhance the flavour of your coffee.

Save your choice using the

key.

20

NA

TOTAL COFFEES

This function displays the number of coffees already

dispensed by the appliance.

Use the

key to select the function:

TOTAL COFFEES *

TIMER

Enable it with the key.

The display shows (e.g.):

TOTAL COFFEES

81

Press key to exit.

TIMER

This function enables you to save energy when the

machine is not used for long periods.

This function is preset by the manufacturer and is

automatically enabled.

STANDBY

after 3 hours from the use.

! Switch-off time can be regulated at 15-minute intervals

with a minimum of 15 minutes. The function cannot be

disabled.

Use the

key to select the function:

TIMER *

CLOCK

Enable it with the key.

The display shows:

ENERGY SAVING

AFTER 3:00

Select the automatic switch-off interval by pressing the

key and use the key to save.

! Note: if automatic switch-on/off times are enabled in

“CLOCK” mode, this function will be ignored.

CLOCK

This function is enabled and/or disabled by the user

and:

- displays the exact time when the machine is in

“STANDBY” or “SELECT FUNCTION” mode.

- selects the on/off time.

To correctly program this function, the exact time must

be set

Use the

key to select this function:

CLOCK *

RINSING CYCLE

Enable it with the key.

Use the

key to select this function:

CLOCK TIME *

ON/OFF TIME

Enable it with the key.

CLOCK TIME

0:00

Set the current time by pressing the key and

save using

key;

Next, press the

key to set the minutes and save

using

key.

The time is set and the machine returns to the previous

menu.

! Note: the time is memorised when the machine is

switched off.

To display the time

Use the

key to select this function:

SHOW CLOCK TIME *

AUTOMATIC ON/OFF

Enable it with the key.

Programming

La page charge ...

Scholtes CL 1 Instructions For Use Manual

Scholtes CL 1 Instructions For Use Manual

dans d''autres langues

Autres documents