Vulcan 36R-2B24GT Le manuel du propriétaire

ITW Food Equipment Group, LLC

3600 North Point Blvd

Baltimore, MD 21222

RETAIN THIS MANUAL FOR FUTURE USE

FORM F38201 Rev. D (11-15)

INSTALLATION &

OPERATION MANUAL

VULCAN ENDURANCE / WOLF CHALLENGER

Gas Restaurant Ranges

MODELS:

12(F) 24S(F)

36(S,C)(F)

48(S,C)(F) 48SS(F)

60(S,C)(S,C)(F) 72(S,C)(S,C)(F)

www.vulcanequipment.com

www.wolfequipment.com

36SF-6B shown

- 2 -

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED

FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

In the event a gas odor is detected, shut

down units at main shutoff valve and

contact the local gas supplier for service.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors or liquids in the vicinity of

this or any other appliance.

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, injury or death. Read the

installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

- 3 -

CONTENTS

OPTIONAL FIELD INSTALLABLE ACCESSORIES ............................................................................ 4

INSTALLATION ....................................................................................................................................... 5

UNPACKING ......................................................................................................................................... 5

DOOR REMOVAL ................................................................................................................................ 5

LOCATION ............................................................................................................................................ 6

INSTALLATION CODES AND STANDARDS ................................................................................... 6

LEG/CASTER ASSEMBLY .................................................................................................................. 7

FLUE RISER and SHELF INSTALLATION ........................................................................................ 8

LEVELING ............................................................................................................................................. 9

BULLNOSE INSTALLATION.............................................................................................................. 9

INSTALLATION OF GRIDDLE/BROILER BRICKS ....................................................................... 12

PLUMBING .......................................................................................................................................... 12

GAS CONNECTIONS ......................................................................................................................... 12

TESTING THE GAS SUPPLY SYSTEM ........................................................................................... 13

ELECTRICAL CONNECTIONS ......................................................................................................... 13

OPERATION ............................................................................................................................................ 13

CONTROLS ......................................................................................................................................... 13

BEFORE FIRST USE ........................................................................................................................... 14

LIGHTING PILOTS ............................................................................................................................. 14

SHUTTING DOWN ............................................................................................................................. 17

OPERATING SUGGESTIONS............................................................................................................ 17

LOADING AND UNLOADING THE OVEN ..................................................................................... 18

CLEANING .............................................................................................................................................. 18

DAILY CLEANING ............................................................................................................................. 18

EXTERIOR CLEANING ..................................................................................................................... 19

MAINTENANCE & ADJUSTMENTS .................................................................................................... 20

TROUBLESHOOTING ............................................................................................................................ 21

- 4 -

INSTALLATION, OPERATION AND CARE OF VULCAN

ENDURANCE / WOLF CHALLENGER GAS RESTAURANT

RANGES

PLEASE KEEP THIS MANUAL FOR FUTURE USE

GENERAL

Vulcan Endurance and Wolf Challenger ranges and ovens are produced with quality workmanship and

material. These ranges are designed with efficiency in cooking performance, sanitation and ease of

cleaning ability in mind. Proper installation, usage and maintenance of your range will result in many

years of satisfactory performance.

The manufacturer suggests that you thoroughly read this entire manual and carefully follow all of the

instructions provided.

OPTIONAL FIELD INSTALLABLE ACCESSORIES

ACCESSORY CODE DESCRIPTION

3/4QDH-4FT

1INFLEX-4FT

¾" (18.75 mm) flex hose / quick disconnect 4’ (1219 mm long).

1" (25 mm) flex hose / quick disconnect, 4' (1219 mm) long.

ALTIKIT-CARN

(01,03,05,07,09)

ALTIKIT-CARP

(02,04,06,08,10)

Altitude Kit - Available in Natural Gas or Propane (LP) for the following

altitudes:

0-1999 ft, 2000-3999 ft, 4000-5999, 6000-7999, 8000-9999.

CASTERS-RR4

CASTERS-RR8

CASTERS-ADJRR4

CASTERS-ADJRR8

Set of four (4) standard casters.

Set of eight (8) standard casters.

Set of four (4) adjustable casters.

Set of eight (8) adjustable casters.

CONNECT-CHALL Inter-Plumb kit for connecting for Salamander/Cheesemelter to range.

CONRACK-XL(20,26)

OVNRACK-XL(20,26)

RKGUIDE-XL

1 extra oven rack with convection ovens.

1 extra oven rack with standard ovens.

1 pair of rack guides (set of 2).

CURBMNT-XL4 Curb mounting kit. Two (2) sets required for 48", 60", and 72" ranges.

OTB-STEPUP Step up rear burner 4”. One kit needed per burner.

RCCONRL-

(24,36,48,60,72)

Condiment Rail Assembly - Replaces standard bullnose. Available for 24",

36", 48", 60", and 72" ranges. (Does not include condiment pans)

RCCUTBD-

(24,36,48,60,72)

Cutting Board Assembly - Replaces standard bullnose. Available for 24", 36",

48", 60", and 72" ranges. (Includes Sani-TUFF® all-rubber cutting board)

RCTWLBR-

(24,36,48,60,72)

Towel Bar Assembly - Replaces standard bullnose. Available for 24", 36", 48",

60", and 72" ranges.

RSHELF-XL

(24,36,48,60,72)

Reinforced High Shelf - 23" (584 mm) high stainless steel backsplash with

broiler mounting brackets for Salamander/Cheesemelter.

SHIELD-FRYRH

SHIELD-FRYLH

Fryer Splash Shield - Right hand or left hand side. Protects range top against

grease splatter from adjacent fryer.

- 5 -

STUB10-XL

(12,24,36,48,60,72)

10" Stainless steel stub riser. Available for 12", 24", 36", 48", 60", and 72"

ranges.

VFLANGED-FEET/4 Set of four (4) flanged feet. Two (2) sets required for 48", 60", and 72" ranges.

INSTALLATION

UNPACKING

This range was inspected before leaving the factory. The transportation company assumes full

responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for

possible shipping damage. If the range is found to be damaged, save the packaging material and

contact the carrier within 5 days of delivery.

Carefully unpack range(s) and place in the approximate installation position. Remove parts packed in a

small cardboard box from oven cavity or shipped separately in finishing kit.

If burner has been shipped using any package strapping devices, remove these before installing the

range.

Before installing, check the type of gas supply (natural or propane) to make sure they agree with the

specifications on the rating plate located on the inside of the kick panel. If the supply and equipment

requirements do not agree, do not proceed with the installation. Contact your dealer immediately.

If it is necessary to remove the door for access through a kitchen door, follow the instructions below for

removal of the door, and subsequent installation of the door.

DOOR REMOVAL

1. Open door.

2. Grasp door firmly at both sides.

3. Lift door upward and pull it out so bottom hinge tabs disengage.

* This may be easier to accomplish one side at a time.

4. Close door almost shut and lower slightly to disengage top hinge tab.

5. Pull door outward.

DOOR INSTALLATION

1. Grasp door firmly at both sides.

2. Starting with either LH or RH top hinge tab, angle door and slide top hinge tab into opening between

hinge stop roller and hinge stop pin.

3. Lift door up (compress door hinge as if opening the door) and position bottom tab downward about

30 degrees down from horizontal.

4. Push door inward, inserting downward angled bottom hinge tab into opening just above hinge stop

pin.

* Bottom hinge tab must enter chassis at downward angle to engage.

5. Bottom hinge tab should engage on hinge stop pin.

6. Open door and pull door outward until bottom hinge tab locks on hinge stop pin.

7. Repeat above steps for opposite side.

8. Open and close door to make sure door hinges are locked in place and operate smoothly.

- 6 -

LOCATION

The equipment area must be kept free and clear of combustible substances.

Installation clearances: COMBUSTIBLE NON-COMBUSTIBLE

CONSTRUCTION CONSTRUCTION

Back: 6" (152 mm) 0"

Right Side: 10" (254 mm) 0"

Left Side: 10" (254 mm) 0"

The installation location must allow adequate clearances for servicing and proper operation. A minimum

front clearance of 35" (889 mm) is required.

The ranges are suitable for installation on combustible floors when 6" (152 mm) adjustable legs or

casters are used. When legs or casters are removed, use only on noncombustible floors, curb, or

platform, with front appliance base projecting 3" (76 mm) beyond curb or platform.

The range(s) must be installed so that the flow of combustion and ventilation air will not be obstructed.

Adequate clearance for air openings into the combustion chamber(s) must be provided. Make sure

there is an adequate supply of air in the room to allow for combustion of the gas at the burners.

INSTALLATION CODES AND STANDARDS

Your Vulcan Endurance / Wolf Challenger Range must be installed in accordance with:

In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). This shall include but

not be limited to: NFPA #54 Section 10.3.5.2 for Venting. Copies may be obtained

from The American Gas Association Accredited Standards Committee Z223, @ 400 N.

HINGE ASSEMBLY

TOP HINGE TAB

BOTTOM

HINGE

TAB

- 7 -

Capital St. NW, Washington, DC 20001 or the Secretary Standards Council, NFPA, 1

Batterymarch Park Quincy, MA 02169-7471.

NOTE: In the Commonwealth of Massachusetts

All gas appliances vented through a ventilation hood or exhaust system equipped with

a damper or with a power means of exhaust shall comply with 248 CMR.

3. NFPA Standard # 96 Vapor Removal from Cooking Equipment, latest edition, available

from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

In Canada:

1. Local codes.

2. CAN/CSA-B149.1 Natural Gas Installation (latest edition)

3. CAN/CSA-B149.2 Propane Installation Code (latest edition), available from the

Canadian Gas Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3

The above are available from the Canadian Standard Association, 5060 Spectrum Way, Suite 100,

Mississauga, Ontario, Canada L4W 5N6.

LEG/CASTER ASSEMBLY

The range is provided with 6"(152 mm) adjustable stainless steel legs (hardware included), packaged in

a box located inside of the oven or in a finishing kit. A set of 6"(152 mm) casters (adjustable or non-

adjustable) are available as an optional field installable accessory.

RANGE SERIES (width) LEGS TO INSTALL CASTERS TO INSTALL

12" 4 4

24" 4 4

36" 4 4

48" 8 8

60" 8 8

72" 8 8

Installation of Legs/Casters:

1. Carefully tip range on its side or back. Rear flue assembly can be removed to avoid damage.

2. Align holes in leg/caster mounting plate with pre-drilled holes on the bottom of range located in

each of the four corners. Four additional legs/casters must be installed on the 48", 60", and 72"

ranges.

3. Attach mounting plate to bottom of range using four (4) ¼ - 20 x ¾“ thread cutting screws

(provided). If casters are being installed, the locking casters should be mounted on the front.

4. After all legs/casters have been installed, carefully return the range to its upright position.

(For additional leg information, see “LEVELING” section of this manual).

Ranges mounted on casters must use a flexible connector (not included) that complies with the

Standard for Connectors for Movable Gas Appliances, ANSI Z21.69•CSA 6.16 and a quick-disconnect

- 8 -

device that complies with the Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI

Z21.41•CSA 6.9. In addition, adequate means must be provided to limit movement of the appliance

without depending on the connector and the quick-disconnect device or its associated piping to limit

appliance movement. Attach the restraining device at the rear of the range.

If disconnection of the restraint is necessary, turn off the gas supply before disconnection. Reconnect

this restraint prior to turning the gas supply on and returning the range to its installation position.

If the range is installed on casters and is moved for any reason, it is recommended that the range be

re-leveled front to back and side to side for even baking.

FLUE RISER and SHELF INSTALLATION

1. Engage Tab on Channels into the slots in the back of the Chassis Top (shown).

2. Install Rear Channels and tighten mounting screws (QTY8 for 12", 24", 36", and 48" ranges,

QTY 12 for 60" ranges, and QTY 16 for 72" ranges). All mounting Screws are #10-24 x ½

unless noted otherwise.

(For units shipped with a pre-assembled backsplash assembly, skip to Step 5.)

3. Slide Back Splash down over the Rear Channels.

4. Install the Rear Heat Shield and tighten mounting screws to the Rear Channels (QTY 8 for 24,

36, 48 or QTY 12 for 60 or QTY 16 for 72) and to the Flue Exhaust (QTY 2 for a Single Oven or

QTY 4 for Double Oven).

5. Install Shelf over the top of the Back Splash; ensure the channel on the top of the Shelf

engages the top flange of the Back Splash.

6. Reinstall Rear Grates if they were removed to install Back Splash and Shelf.

DO NOT obstruct the flow of flue gases from the flue located on the rear of the range. Proper venting

of flue gas is vital to the safe and efficient operation of the range. Problems arising from the intentional

obstruction of the flue will result in voiding of warranty. It is recommended that the flue gases be

ventilated to the outside of the building through a ventilation system installed by qualified personnel.

Channel to Chassis

Interface Detail

- 9 -

From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18"

(457 mm) must be maintained. Information on the construction and installation of ventilating hoods

may be obtained from the standard for "Vapor Removal from Cooking Equipment," NFPA No. 96 (latest

edition), available from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

LEVELING

To level the range, place a carpenter's level on the range top and check leveling of the unit side to side

and front to rear. Achieve leveling by turning each foot section of the unit's leg as needed. Turning the

foot in a counter clockwise direction will increase height and clockwise will decrease.

BULLNOSE INSTALLATION

1.) Remove Grate Castings along the front of edge of the Range.

2.) Slide Bullnose over mounting bracket and align with Range so that it is not offset in either

direction.

3.) Start screw at one end of the Range, do not tighten completely.

4.) Going across the width of the Range install the next screw, as shown in Figure 2, set the

alignment and tighten screw completely.

5.) Install the remaining screws and tighten all screws completely.

Condiment Rail

(Accessory)

Cutting Board

(Accessory)

Towel Bar

(Accessory)

Standard

Bullnose

Remove Grates

on Gas Range

Figure 1

- 10 -

Re-install the Grate Castings along the front edge of the range.

MOTOR ASSEMBLY INSTALLATION INSTRUCTIONS

1. Remove the oven racks and the box containing legs, regulator and plumbing fittings. In some

instances, the legs, regulator and plumbing fittings will be shipped in separate finishing kit. Check

that all the listed components shown in figure are present.

2. Remove the packaging and motor grease guard from inside the oven and slide out the rack

guides. Tip the Motor Assembly to upright position.

3. Push the motor assembly to the rear in the oven cavity, taking care not to pinch the power cord or

the wiring conduit. Assemble the motor assembly from the inside of the oven and the blower

cover with #10-24 x ½ phillips truss head screws provided in the hardware bag.

Install Screws, #10-24 x

½ Phillips Head, in slots

on Bullnose as noted.

Note: Align the end of

the Bullnose with the

Range for fit.

Figure 2

LH Rack Guide

Motor Assembly

RH Rack

Guide

Motor Grease

- 11 -

4. Ensure that blower cover is assembled such that air deflector is to the bottom side of the oven.

(See picture below).

5. Remove protective plastic on the rack guides. Assemble rack guides by inserting the two tabs into

slots on the side wall. Insert oven racks.

6. Assemble the motor grease guard from the rear of the unit with QTY 4 #10-24 x ½ screws.

Air

Deflector

- 12 -

INSTALLATION OF GRIDDLE/BROILER BRICKS

1. Remove six 5 ¼” x 2 ¼” (133 x 57 mm) and six 5 ¼” x 5

1

⁄

16

” (133 x 129 mm) bricks from the

shipping box packaged in the oven cavity.

2. Install the 5 ¼” x 2 ¼” (133 x 57 mm) bricks to the left and right hand sides of the broiler by inserting

the bricks individually through the front opening in the broiler. Angle the brick sideways for easy fit

between the burner edges. Set the bricks flat in place, resting on the broiler side and burner edges.

Push each brick as far to the rear of the broiler as possible to ensure easy fit of the last brick.

3. Install the remaining six 5 ¼” x 5

1

⁄

16

” (133 x 129 mm) bricks to the center section as described in

step 2. Place the bricks on the center burner edges only.

PLUMBING

A preset gas pressure regulator and plumbing fittings are shipped uninstalled. This regulator must be

installed by an authorized service person before the unit is placed into operation. See full unit data plate

located on the rear of the range, or the secondary data plate, riveted to the kick panel, for pressure

regulator setting information. If a manometer is being used, utilizing one of the available pressure taps

in the manifold, the manifold pressure with one burner on should be ± 0.3" W.C. of the value indicated

on the rating plate.

1. Refer to the Modular Range Field Plumbing Reference Guide (p/n 921861 or 960167) shipped with

the regulator and fittings for 48", 60", and 72" ranges.

2. Cover the pipe threads with pipe joint compound resistant to propane gases.

3. For 12", 24", and 36" ranges, screw the reducer, pipe nipple, and regulator onto the pipe with the

regulator flow direction arrow pointing towards the back of the unit and the regulator adjustment in

the upright position.

For 48", 60", and 72" ranges, follow the assembly steps as detailed in the Modular Range Field

Plumbing Reference Guide.

4. The pressure regulator must be mounted horizontally to ensure the proper preset outlet pressure. If

mounted in any other direction, the outlet pressure must be rechecked and possibly reset. A leak

limiter is supplied with every regulator to allow excess gas pressure to escape. Do not obstruct the

limiter or the gas regulator, as obstruction may cause the regulator to malfunction.

GAS CONNECTIONS

All gas supply connections and any pipe joint compound used must be resistant to the action

of propane gases.

Prior to lighting, check all joints in the gas supply line for leaks. Use soap and

water solution. Do not use an open flame.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

- 13 -

TESTING THE GAS SUPPLY SYSTEM

When test pressures exceed ½ psig (3.45 kPa), the range and its individual shutoff valve must be

disconnected from the gas supply piping system.

When test pressures are ½ psig (3.45 kPa) or less, the range must be isolated from the gas supply

system by closing its individual manual shutoff valve.

ELECTRICAL CONNECTIONS

Electrical and grounding connections must comply with the applicable portions

of the National Electrical Code and/or other local electrical codes.

Disconnect the electrical power to the machine and follow Lockout / Tagout

procedures.

Appliances equipped with a flexible electrical supply cord are provided with a

three-prong grounding plug. It is imperative that this plug be connected into a properly

grounded three-prong receptacle. If the receptacle is not the proper grounding type, contact an

electrician. Do not remove the grounding prong from this plug.

The convection range is designed for 120 volt power supply and is provided with a flexible electric

supply cord and plug that must be plugged into the proper receptacle. Do not connect the convection

range to electrical supply until after gas connections have been made. The wiring diagram for the

convection range is located on the rear of the appliance.

OPERATION

QUALIFIED PERSONNEL SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

The appliance and its parts are hot. Use care when operating, cleaning, or

servicing the appliance.

CONTROLS

Open Top Burner Valve — Allows gas to flow to the top burners. To open valve, turn knob

counterclockwise. To close valve, turn knob clockwise.

Manual Griddle Valve — Allows gas to flow to the griddle burners. To open valve, turn knob

counterclockwise. To close valve, turn knob clockwise.

Griddle Thermostat — Regulates griddle temperature. The thermostat temperature range is from

LOW at approximately 200°F (93°C) to HI at approximately 550°F (288°C). Turn the thermostat

clockwise to increase temperature and counterclockwise to decrease temperature.

Oven Thermostat — Regulates oven temperature. The thermostat temperature range is from LOW at

approximately 250°F (121°C) to HI at approximately 500°F (260°C). Turn the thermostat

counterclockwise to increase temperature and clockwise to decrease temperature. Oven temperature

regulation is the most accurate between 300°F (149°C) and 500°F (260°C).

- 14 -

Safety Valve – Monitors standing pilot. All ovens, thermostatic griddles, and select open top burner

devices (Flame Safety models) feature a standing pilot that is monitored by a thermocouple and pilot

safety valve. If the pilot goes out, the safety valve will shut-off the gas supply to the pilot and main

burners.

Fan Switch – Turns fan on and off (Convection Ovens only). Fan turns on when door is closed. Fan

turns off when door is opened.

BEFORE FIRST USE

Open Top

Remove top grates from range top to carry out initial seasoning. Do not season the grates while

installed on the range top. Once grates are removed from range, apply a light coating of liquid

vegetable or spray-type cooking oil to each grate.

After seasoning, replace grates onto the range. Turn on all open top sections to LOW and allow to burn

for at least 15 minutes before using pots or pans on the range top. Failure to season grates will cause

grates to rust. Upon initial use, grates may show white coloring. This will go away over time with proper

seasoning care. Use of water and a wire or stiff brush on the grate, followed by immediate drying before

the next seasoning will help preserve the cast iron color.

Ovens

New ovens require a burn off period to break in the oven and eliminate unappetizing odors from

penetrating the food product.

Turn on gas to unit and set the thermostat to 475°F (246°C). Allow the oven to operate at this

temperature for 30 to 45 minutes.

Griddles

Before leaving the factory the griddle is coated with vegetable oil as a rust inhibitor. Remove this film

when the griddle plate is being cleaned prior to its first cooking use. Heat the griddle to 200-300°F to

loosen and melt the coating, then clean the surface with a non-corrosive, grease dissolving commercial

cleaner, following the manufacturer’s directions. Rinse thoroughly and wipe dry with a soft clean cloth.

Clean all accessories.

The griddle plate is steel, but the surface is soft and can be scored or dented by

careless use of spatulas or scrappers. Be careful not to dent, scratch or gouge the plate. Do

not try to knock off loose food that may be on the spatula by tapping the corner edge of the

spatula on the griddle surface.

Season the griddle to avoid possible surface corrosion before first use, and after every cleaning. Heat

griddle to a low temperature (300-350°F) and apply a small amount of cooking oil – about one ounce

per square foot of surface. Use a soft lint-free cloth to spread the oil over the entire griddle surface to

create a thin film. Wipe off any excess oil with a cloth. Repeat the procedure until the griddle has a

slick, mirror-like finish.

LIGHTING PILOTS

All burner configurations are equipped with standing pilots allowing for instant appliance use

and low maintenance. Lighting should be infrequent except during initial start-up or full

appliance shut-down.

- 15 -

Pilot safety monitoring is standard on all ovens and thermostatic griddles and is optional for

open top burner devices (Flame Safety models). Manual piezo ignition may be provided.

Open Top Burner, Manual Griddle

1. Remove front row of grates (Open Top Only).

2. Turn the main gas supply valve to the ON position.

3. Light all standing pilots.

Open Top - Pilot access can be reached under the grates.

Manual Griddle – Pilot access can be reached under the griddle plate through the slotted

opening in the manifold cover near the burner valve knob.

4. Turn the burner valve ON to ensure operation.

5. If burners fail to light, turn off all valves, and call an authorized installation or service person.

6. Turn the burner valve to the OFF position. Pilot remains lit.

Open Top Burner (Flame Safety models)

1. Remove front row of grates.

2. Turn the main gas supply valve to the ON position.

3. Depress and hold safety valve button and light pilot either conventionally or using rotary piezo

igniter. Repeat for each safety valve. Rotary piezo igniter operation is shown below.

4. Turn the burner valve ON to ensure operation.

5. If burners fail to light, turn off all valves, and call an authorized installation or service person.

6. Turn the burner valve to the OFF position. Pilot remains lit.

- 16 -

Griddle/Broiler

1. Turn the main gas supply valve to the ON position.

2. Light all standing pilots.

Pilot access can be reached under the griddle through the broiler opening. The pilot burner is

on the bottom left side of the griddle/broiler burner.

3. Turn the burner valve ON to ensure operation.

4. If burners fail to light, turn off all valves, and then call an authorized installation or service person.

5. Turn the burner valve to the OFF position. Pilot remains lit.

Thermostatic Griddle

1. Turn the thermostat to the OFF position.

2. Turn the main gas supply valve to the ON position.

3. Depress and hold the red button on the safety valve and light the pilot through the slotted opening

in the manifold cover near the burner valve knob.

4. Hold red button down for at least 30 seconds.

5. When button is released, pilot should remain lit.

6. Pilot flame must be high enough to heat thermocouple.

7. Turn thermostat ON to ensure operation.

8. If ignition fails, turn the control knob to OFF. Wait 5 minutes and repeat the above procedure.

DO NOT attempt to relight pilot without waiting 5 minutes.

9. Turn the burner valve to the OFF position. Pilot remains lit.

Oven (Standard & Convection)

1. Turn thermostat to OFF position.

2. Turn the main gas supply valve to the ON position.

3. Lift up on the kick panel and rotate down 90°.

4. Depress red button on safety valve and light pilot through opening in burner box area.

5. Hold red button down for at least 30 seconds.

6. When button is released, pilot should remain lit.

7. Pilot flame must be high enough to heat thermocouple.

- 17 -

8. Return the kick panel to original position.

9. Convection Oven – Turn on fan switch located between oven control knob and pilot safety valve.

10. Turn thermostat ON to ensure operation.

11. Standard Oven – If ignition fails, turn the oven control knob to OFF. Wait 5 minutes and repeat

the above procedure.

Convection Oven – If ignition fails, turn the fan switch and oven control knob to OFF. Wait 5

minutes and repeat the above procedure.

DO NOT attempt to relight pilot without waiting 5 minutes.

12. Standard Oven – Turn the burner valve to the OFF position. Pilot remains lit.

Convection Oven – Turn the burner valve and fan switch to the OFF position. Pilot remains lit.

SHUTTING DOWN

All burners are equipped with standing pilots that remain lit when control valves are turned OFF.

Convection ovens will additionally need the fan switch turned OFF.

For complete range shutdown, and to extinguish all pilots, turn off main gas supply.

OPERATING SUGGESTIONS

Open-Top Burners

Open-top burners are quickly lit and require no preheating time. Open top burners have a wide low to

high burner flame adjustment range. This allows for better simmering performance at the lowest

possible stabilized setting. When simmering, turn the burner valve knob down until you reach the

optimum lowest burner flame setting to maintain the desired simmer point.

Manual Griddle

Pre-heat the griddle top for approximately 15 - 20 minutes before cooking. The top can be kept hot with

burners turned partially down. During off periods, turn the burners down or heat only half of the top.

Thermostatic Griddle

Pre-heat the griddle top for approximately 15 - 20 minutes before cooking. The griddle thermostats

regulate temperatures for each 12" section of the griddle from a low setting at approximately 200°F

(93°C) to high setting at approximately 550°F (288°C).

Standard Oven Cooking

Allow time to preheat ovens before using (25 minutes to 400°F [204°C]). The oven thermostat regulates

temperature from a low setting at approximately 250°F (121°C) to high setting at approximately 500°F

(260°C). If properly used, the automatic temperature control is an efficient system. Turn thermostat

down to LOW when oven is idling, or turn the oven control to OFF when not in use.

Moderate oven temperatures will produce better food, reduce shrinkage and keep maintenance costs

down. Using a low temperature for roasting (recommended 325°F [162°C] or lower) will reduce meat

costs by reducing shrinkage.

A pan of water (approximately 12" x 20" x 1" [305 mm x 508 mm x 25.4 mm]) may be placed in the

oven bottom. This water supplies humidity to reduce shrinkage. If necessary, add water during roasting.

- 18 -

Convection Oven Cooking

Cooking time and temperature in convection oven may vary slightly from normal time and temperature.

LOADING AND UNLOADING THE OVEN

Open the door and load the oven as quickly as practical to conserve heat. Take care to avoid spilling

liquids while loading. Close the door and refer to recipe for cooking time.

Provide adequate space for product unloading. Rapid unloading will conserve heat and ensure proper

reheating conditions for the next load, if applicable.

CLEANING

Disconnect the electrical power to the machine and follow Lockout / Tagout

procedures.

Shut off the gas before cleaning the appliance.

The appliance and its parts are hot. Be very careful when operating, cleaning, or

servicing the appliance.

Exterior surfaces may be cleaned using soft cloth and mild detergent. Do not use Dawn

®

dish detergent

to clean the exterior or interior components of the range.

Do not use scouring powder. It is extremely difficult to remove completely. It can build up accumulations

that will damage the oven.

Vulcan / Wolf equipment is strongly constructed and is designed to give you long, satisfactory service at

low cost, provided you give it proper care. Frequent cleaning and occasional adjusting should reward

you with low operating and maintenance costs and faster, better service.

DAILY CLEANING

Open Top

Clean cast iron open top grates with a mild soap and water solution. Rinse thoroughly and dry with a

clean, water-absorbent towel. Immediately after drying (with grates still removed from the range top),

season grates lightly with liquid vegetable or spray-type cooking oil.

After seasoning, replace grates onto the range. Turn on all open top sections to LOW and allow them to

burn for at least 15 minutes before using pots or pans on the range top. Season the open top grates

after each cleaning. Failure to season grates will cause grates to rust.

Griddle Top with Tray

Empty the grease drawer as needed throughout the day and regularly clean at least once daily. The

Grease tray has a weep hole to indicate that grease tray is full. Service calls resulting from failure to

properly empty grease tray/drawer will not be covered under warranty.

Clean the griddle regularly. A clean griddle always looks better, lasts longer and performs better. To

produce evenly cooked griddle products, keep the griddle plate clean and free of carbonized grease.

Carbonized grease on the surface hinders the transfer of heat from the griddle surface to the food,

- 19 -

resulting in spotty browning and loss of cooking efficiency. Carbonized grease tends to cling to griddle

foods, giving them a highly unsatisfactory and unappetizing appearance.

After each use, clean the griddle with a scouring pad or flexible spatula.

Once a day, thoroughly clean the griddle back splash, sides and front. Remove, empty and wash the

grease drawer in the same manner as an ordinary cooking utensil.

Oven

Remove chrome-plated racks and clean in a sink.

While still warm, wipe top with a soft cloth or other grease absorbing material to remove spillovers,

grease, etc., before they burn in.

Clean oven and oven door daily, especially if fruit pies or tomato sauces were baked, meats roasted,

and if there have been spillovers.

After processing some foods at low temperatures, odors may linger in the oven. These odors may be

cleared by setting the thermostat at 500°F (260°C) and allowing the oven to operate unloaded for 30 to

45 minutes.

EXTERIOR CLEANING

Daily

Clean exterior finish with a mild solution of soap or grease-dissolving cleaner. To remove discoloration,

use a nonabrasive cleaner. Always rub with the grain of the metal. Stainless steel areas of the range

can be polished by using a soft dry cloth. If needed, add stainless steel polish to the soft cloth.

STAINLESS STEEL

Here are a few simple cleaning procedures that have been found effective for keeping stainless steel

equipment clean, sparkling and bright.

General Cleaning

Use ordinary soap or detergent and water for routine cleaning of stainless steel. To prevent water spots

and streaks, rinse thoroughly with warm water and wipe dry with a soft clean cloth. The addition of a

rinsing agent will also help prevent spotting. Do not pressure wash any portion of the range.

Fingerprints

Fingerprints are sometimes a problem on highly polished surfaces of stainless steel. They can be

minimized by applying a cleaner that will leave a thin oily or waxy film. To use these cleaners, simply

wipe on and remove excess with a soft dry cloth. After using, subsequent fingerprints will usually

disappear when wiped lightly with a soft cloth or with a cloth containing a little of the cleaner. If the

surface is especially dirty to start, wash first with soap or detergent and water.

Heat Tint

Straw-colored or slightly darkened areas may appear on stainless steel in and around ovens and

ranges where temperatures reach 500°F (260°C) or more. This "heat tint" is caused by a slight

oxidation of the stainless steel and is not harmful. To control or minimize this condition, never use

more heat than is absolutely necessary.

- 20 -

MAINTENANCE & ADJUSTMENTS

Disconnect the electrical power to the machine and follow Lockout / Tagout

procedures.

LUBRICATION

All moving parts must be checked for wear and lubricated. Contact your local authorized servicer.

Motors in Vulcan Endurance / Wolf Challenger convection ranges are permanently lubricated and

require no additional maintenance.

FLUE

Check the flue when it is cool to be sure it is free of obstructions.

SERVICE AND PARTS INFORMATION

To obtain service and parts information, contact an authorized service agency in your area (refer to our

website, www.vulcanequipment.com or www.wolfequipment.com for a complete listing of authorized

service and parts depots). When calling for service, the following information must be available: model

number, serial number, and gas type. This information can be found on the main data plate, located on

the rear of the unit, or on the secondary plate located inside the lower front kick panel. Lift up and lower

the front kick panel to view the secondary data plate.

PRECAUTIONS

When scraping off heavy deposits of grease or oil from stainless steel equipment, never use ordinary

steel scrapers. Particles of ordinary steel may become embedded in, or lodge on, the surface of the

stainless steel. These will rust, causing unsightly stains and possible contamination of food. If it is

necessary to scrape, use stainless steel, wood, plastic or rubber tools.

Convection

Oven W

iring

D

iagram

La page charge ...

Vulcan 36R-2B24GT Le manuel du propriétaire

Vulcan 36R-2B24GT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents