Owner’s Manual — Phoenix CAM
Installation, Operation & Service Instructions
1
www.usephoenix.com • sales@thermastor.comToll-Free 1-800-533-7533
Read and Save These Instructions
Low amp draw, balanced airflow characteristics and maximum velocity of 2700 FPM are what propel the
Phoenix to rise above the competition.
The unique 1/3 horsepower design of the Phoenix Centrifugal Air Mover, coupled with a two-speed switch,
allows the restoration technician to deliver the most airflow using the fewest amps.
Maximum amp draw on high speed is 2.8 amps. This drops to a mere 2.4 amps on low speed. It is now
possible to fit as many as four Phoenix Centrifugal Air Movers onto a typical 15 amp household circuit.
The Phoenix CAM is lightweight, stackable, has a power indicator lamp, large three-position switch, and
superior cord management.
The Phoenix housing is durable, washable, and chemical resistant. It features multiple operating positions
allowing it to be angled up from horizontal to 45° and 90°.
The Phoenix Centrifugal Air Mover
• 2-Speed 1/3 Horsepower Motor with automatic-
reset thermal protection.
2.8 Amps on High Speed
2.4 Amps on Low Speed
• Maximum Velocities 2700 FPM
• Balanced Exhaust Airflow
• Directional Airflow
Horizontal, 45° Angle, 90° Angle
• Durable, rugged, chemical resistant housing, fan
wheel, and controls design.
• Operator interface conveniently located for easy
access, featuring: power indicator lamp and large
three-position switch.
• Phoenix exclusive Pilot Light and Sealed Switch are
recessed to prevent damage.
• Ergonomic carry handle and power cord storage.
• Non-marking, anti-skid, rubber feet.
Specifications subject to change without notice.
TS-479 Rev. A 7/08
Phoenix Centrifugal Air Mover
PN 4027508
PO Box 8680 • Madison, WI 53708
2
www.usephoenix.com • sales@thermastor.comToll-Free 1-800-533-7533
Table of Contents
Introduction ...............................................................1
Centrifugal Air Mover Features and Benefits ...................1
1. Safety Information .................................................2
2. Specifications ........................................................3
3. Operating Instructions ...........................................3
4. Operator Panel Features .........................................4
4.1 Power Indication Lamp .....................................4
4.2 3-Position Drying Selector Switch ......................4
5. Maintenance .........................................................4
5.1 Servicing ........................................................4
5.2 Cleaning .........................................................4
6. Replacement Parts and Optional Accessories ...........4
7. Warranty ...............................................................5
Serial No.__________________________________
Purchase Date_____________________________
Dealer’s Name_____________________________
Read the operation and maintenance instructions
carefully before using this unit. Proper adherence to these
instructions is essential to obtain maximum benefit from
your Phoenix 4027508.
1 Safety Information
When using any rotational electrical device basic
precautions should always be followed, including the
following:
CAUTION! For general ventilating use only. Do not use in
environments containing hazardous or explosive materials
and vapors.
• Do not operate the unit without the safety guards
properly installed and secured. Do not operate the unit
if the guards become damaged. Contact Therma-Stor for
replacement parts.
• Always replace the guards as originally installed after
servicing or cleaning the product.
• Never place your face, hands, or other susceptible body
parts in the air stream, inlets, or outlet of this device.
• This fan is not a toy! Ensure children do not play with
and do not have access to the equipment. Do not allow
children to play with or near the unit or in its air flow.
• Do not use this fan with any solid-state speed control
device.
• Do not operate unit with a cut or frayed power cord.
Replace cord if it becomes damaged.
• Handle with care. Do not drop or throw the unit. The
unit can be damaged under harsh treatment.
• Do not unplug the unit by pulling on the cord. Grasp the
plug firmly and pull it out of the wall socket or power
receptacle.
• Always use a grounded outlet.
• Never operate electrical equipment in standing water.
• Never operate with the safety grills removed. Personal
injury may result.
• Do not stick your fingers or other objects through the
safety grills.
• Do not restrict airflow to the unit. This may cause the
unit to overheat.
• Unit should never be serviced or cleaned while it is
plugged in.
• Make sure the unit is secure, stable and safe from
falling over or falling down before operating.
• Do not sit or stand on the unit or use as a shelf.
• Do not leave device plugged in when not in use.
• Indoor use only. Do not expose to water or rain–store
indoors.
• Use only as described in this manual.
• Use only Manufacturer’s recommended attachments.
Contact Therma-Stor for proper repair instructions.
• Do not pull or carry it by the power cord, use cord as a
handle, close doors on cord or pull cord around sharp
edges.
3
www.usephoenix.com • sales@thermastor.comToll-Free 1-800-533-7533
2 Specifications
Part No.
4027508
Power 115 VAC, 60 hz.
Operating 3 – 0°, 45°, 90°
Positions
Drive Motor 1 /3 Horsepower, 2-Speed
Motor Thermal cut-off
Protection
Cord Length 25 Feet
Airflow 2700 ft/min outlet velocity
Current Draw 2.8 Amps High speed, 2.4 Amps Low speed
Warranty One Year - 100% parts and labor
(all components)
Three Years - Only materials and workmanship
of the housing are covered.
3 Operation Instructions
The Phoenix Centrifugal Air Mover is intended for use by
water damage restoration, carpet cleaning, construction,
and janitorial/sanitation professionals in general
ventilating and structural surface drying applications. The
Phoenix Centrifugal Air Mover as packaged is ready to
be put into service. Inspect the unit completely for any
shipping damage. Place the unit on the ground. Plug the
unit into a grounded outlet and select the drying mode.
CAUTION: The Phoenix Centrifugal Air Mover consumes 2.8
Amps on high speed. Do not plug devices requiring more
than 9.3 Amps of current into the duplex outlet.
• Do not run over cord.
• Keep cord away from heated surfaces.
• Do not handle power cord plug with wet hands.
• Turn off all controls before unplugging.
• Do not use when you are tired, distracted or under the
influence of drugs, alcohol or medication.
LIRE ET CONSERVER CES INSTRUCTIONS
• Risque de choc électrique Peut causer des blessures ou
la mort. Débrancher toutes les alimentations en courant
électrique à distance avant l’entretien ou le nettoyage.
• Ne pas utiliser l’appareil avec un cordon d’alimentation
coupé ou effiloché.
• Ne pas débrancher l’appareil en tirant sur le cordon.
Tenir la fiche fermement et la tirer hors de la prise
murale ou la prise d’alimentation électrique.
• Toujours utiliser une prise mise à la terre.
• Ne jamais utiliser l’équipement électrique dans de l’eau
stagnante.
• Ne jamais utiliser sans les grilles de protection. Des
blessures risquent d’en résulter.
• Ne pas brancher plus de 8 ampères au total au
différentiel.
• Vérifier la protection du différentiel avant chaque
utilisation en appuyant sur le bouton “ test “. Si
l’appareil fonctionne correctement, le bouton “ reset “
ressort.
• Ne pas passer les doigts ou d’autres objets dans les
grilles de protection.
• Ne pas diminuer le débit d’air arrivant jusqu’à l’appareil.
L’appareil risque de trop chauffer.
• Ne pas s’asseoir ou se tenir debout sur l’appareil; ne
pas l’utiliser comme étagère ou table.
• Avant de laisser un appareil aéraulique axial sans
surveillance, s’assurer que les enfants n’ont pas accès
à l’équipement. Ne pas laisser les enfants jouer avec
l’appareil ou à proximité de l’appareil ou dans l’air qu’il
projette.
• Pour réduire le risque d’incendie ou de choc électrique,
ne pas utiliser ce ventilateur avec un dispositif de
commande de vitesse à semi-conducteurs.
Dimensions Machine Shipping
Width 17” 17.3”
Height 20” 20”
Depth 19.4” 20”
Weight 26.5 lb 28 lb
4
www.usephoenix.com • sales@thermastor.comToll-Free 1-800-533-7533
4 Operator Panel Features
4.1 Power Indication Lamp
The red, sealed, high intensity AC voltage power indication
lamp allows operators to visually identify the operation
status of several Phoenix Centrifugal Air Movers at a
distance, with a single glance. The power indication lamp
will remain lit when the AC power cord is plugged into a
standard “powered” AC power outlet and the
3-Position drying selector switch is in either the HIGH or
LOW operation position. The power indication lamp will
remain unlit when the AC power cord is unplugged, the
3-Position drying selector switch in the OFF position, or the
connected, standard AC wall outlet power has been turned
off.
4.2 3-Position Drying Selector Switch
The Phoenix Centrifugal Air Mover features a three-position
switch - LOW–OFF–HIGH.
1. Inspect the machine for damage and airflow
obstructions prior to plugging it in or operating it.
2. Ensure the power switch is in the OFF (middle)
position.
3. Place the machine into the desired position for
operation. Ensure that the machine rests stable and
secure and will not overturn.
4. Turn the unit on to the desired speed, high or low.
5 Maintenance
WARNING: Disconnect the unit from power before servicing
or cleaning. Replace the safety grill after
servicing, lubrication or cleaning.
5.1 Servicing
Before each use, inspect for damage, blocked inlet or
outlet, or any excess buildup of foreign material.
When the Phoenix Centrifugal Air Mover is first turned
on, check for excessive vibration. If the unit vibrates
excessively or if blower wheel rubs on housing, turn off the
unit immediately. Have a service technician inspect the
unit to locate the problem.
5.2 Cleaning
The housing is made of a durable and washable
polyethylene. When cleaning, the use of solvents is NOT
recommended.
6 Replacement Parts and
Optional Accessories
Contact the factory at 1-800-533-7533 to order
replacement parts, or optional accessories
5
www.usephoenix.com • sales@thermastor.comToll-Free 1-800-533-7533
Phoenix Centrifugal Air Mover Limited Warranty
Warrantor:
Therma-Stor LLC
PO Box 8680
Madison, WI 53708
Telephone: 1-800-533-7533
Warranty: This warranty covers Phoenix Centrifugal Air Movers, Part Number 4027508
One Year Warranty: - 100% parts and labor (all components)
Three Year Warranty: - Materails and workmanship of the housing only are covered.
If a defect in materials or workmanship occurs within the warranty period, Therma-Stor LLC will repair
or replace the defect.
End-User Responsibilities: Warranty service must be performed by a servicer authorized by Therma-
Stor LLC. To obtain warranty service you must obtain a return material authorization (RMA). To obtain
an RMA you must present proof of purchase or (lease), by use of a warranty card, original sales
receipt or other reasonable and reliable means. To obtain an RMA call Therma-Stor LLC at the above
number and ask for the Therma-Stor LLC Service Department, which will then issue an RMA# and
arrange for, at our option, either repair or replacement.
Freight: Freight to and from the servicer is the responsibility of the end-user. The end-user is
responsible for normal care and proper return packaging.
Limitations and Exclusions: This warranty does not cover any defect, malfunction, etc. resulting from
misuse, abuse, lack of normal care, corrosion, freezing, tampering, modification, unauthorized or
improper repair or installation, accident, acts of nature or any other cause beyond Therma-Stor LLC’s
reasonable control.
If any Phoenix Centrifugal Air Mover part is repaired or replaced, the new part shall be warranted for
the balance of original warranty (but all warranty periods will be extended by the period of time, if any,
that the Phoenix Centrifugal Air Mover is out of service while awaiting covered warranty service).
Warranty service will be performed during normal working hours.
UPON THE EXPIRATION OF THE WRITTEN WARRANTY APPLICABLE TO THE PHOENIX CENTRIFUGAL
AIR MOVER OR ANY PART THEREOF, ALL OTHER WARRANTIES IMPLIED BY LAW, INCLUDING
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL ALSO EXPIRE. ALL
WARRANTIES MADE BY THERMA-STOR LLC ARE SET FORTH HEREIN, AND NO CLAIM MAY BE MADE
AGAINST THERMA-STOR BASED ON ANY ORAL WARRANTY. IN NO EVENT SHALL THERMA-STOR
LLC, IN CONNECTION WITH THE SALE, INSTALLATION, USE, REPAIR OR REPLACEMENT OF ANY
PHOENIX CENTRIFUGAL AIR MOVER OR PART THEREOF BE LIABLE UNDER ANY LEGAL THEORY FOR
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION WATER
DAMAGE (THE END USER SHOULD TAKE PRECAUTIONS AGAINST SAME), LOST PROFITS, DELAY, OR
LOSS OF USE OR DAMAGE TO ANY REAL OR PERSONAL PROPERTY.
Some states do not allow limitations on how long an implied warranty lasts, and some do not
allow the exclusion or limitation of incidental or consequential damages, so one or both of these
limitations may not apply to you.
Legal Rights: This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
-
1
-
2
-
3
-
4
-
5
dans d''autres langues
- English: Phoenix CAM Owner's manual
Documents connexes
-
Phoenix 4030940 Installation, Operation & Service Instructions
-
-
Phoenix FireBIRD Compact 20 Manuel utilisateur
-
-
-
-
Autres documents
-
Therma-Stor Phoenix CAM Pro Le manuel du propriétaire
-
Therma-Stor Products Group TS-285 Manuel utilisateur
-
Ultra-Aire MD33 Installation Instructions Manual
-
Powersoft K6 DSP+AESOP Manuel utilisateur
-
Miller PHOENIX 456 CC/CV Le manuel du propriétaire
-
Hobart Welding Products PHOENIX 456 CC/CV Le manuel du propriétaire
-
-
