Oracle Sun StorageTek SG-PCIEFCGBE-E8-N Guide d'installation

Marque: Oracle

Modèle: Sun StorageTek SG-PCIEFCGBE-E8-N

Taper: Guide d'installation

Ce manuel convient également à

StorageTek Dual 8Gb FC Dual GbE HBA,

ExpressModule, Emulex Installation

Guide For HBA Models SG-XPCIEFCGBE-

E8-Z, SG-PCIEFCGBE-E8-Z, SG-

XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-

N and 7105393

Part No: E20756-06

August 2018

StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-

N, SG-PCIEFCGBE-E8-N and 7105393

Part No: E20756-06

This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except

as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform,

publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is

prohibited.

The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.

If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable:

U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,

delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental

regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the

hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous

applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all

appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this

software or hardware in dangerous applications.

Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of

SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered

trademark of The Open Group.

This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are

not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement

between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content,

products, or services, except as set forth in an applicable agreement between you and Oracle.

Access to Oracle Support

Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit http://www.oracle.com/pls/topic/lookup?

ctx=acc&id=info or visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.

Référence: E20756-06

Ce logiciel et la documentation qui l'accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d'utilisation et

de divulgation. Sauf stipulation expresse de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, accorder de licence, transmettre,

distribuer, exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute

ingénierie inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d'interopérabilité avec des logiciels tiers ou tel que prescrit par la loi.

Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu'elles soient exemptes d'erreurs et vous

invite, le cas échéant, à lui en faire part par écrit.

Si ce logiciel, ou la documentation qui l'accompagne, est livré sous licence au Gouvernement des Etats-Unis, ou à quiconque qui aurait souscrit la licence de ce logiciel pour le

compte du Gouvernement des Etats-Unis, la notice suivante s'applique :

U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,

delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental

regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the

hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

Ce logiciel ou matériel a été développé pour un usage général dans le cadre d'applications de gestion des informations. Ce logiciel ou matériel n'est pas conçu ni n'est destiné à être

utilisé dans des applications à risque, notamment dans des applications pouvant causer un risque de dommages corporels. Si vous utilisez ce logiciel ou ce matériel dans le cadre

d'applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans

des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l'utilisation de ce logiciel ou matériel pour des

applications dangereuses.

Oracle et Java sont des marques déposées d'Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d'autres propriétaires

qu'Oracle.

Intel et Intel Xeon sont des marques ou des marques déposées d'Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques

déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d'Advanced Micro Devices. UNIX est une

marque déposée de The Open Group.

Ce logiciel ou matériel et la documentation qui l'accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de

tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers, sauf mention contraire stipulée

dans un contrat entre vous et Oracle. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des

dommages causés par l'accès à des contenus, produits ou services tiers, ou à leur utilisation, sauf mention contraire stipulée dans un contrat entre vous et Oracle.

Accès aux services de support Oracle

Les clients Oracle qui ont souscrit un contrat de support ont accès au support électronique via My Oracle Support. Pour plus d'informations, visitez le site http://www.oracle.com/

pls/topic/lookup?ctx=acc&id=info ou le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs si vous êtes malentendant.

Contents

Using This Documentation ................................................................................. 7

1 HBA Overview ................................................................................................. 9

Kit Contents ................................................................................................... 9

HBA Features and Specifications ....................................................................... 9

Operating System and Technology Requirements ................................................ 11

System Interoperability ................................................................................... 12

Host Platform Support ............................................................................ 12

Storage Support .................................................................................... 13

Switch Support ..................................................................................... 14

Software Support ................................................................................... 14

Boot Support ................................................................................................ 15

Environmental Requirements ........................................................................... 15

2 Hardware Installation and Removal .............................................................. 17

Observing ESD and Handling Precautions ......................................................... 17

Best Practices for Installing the HBA ................................................................ 18

General Best Practices ............................................................................ 18

Best Practices For Switches and Zoning .................................................... 19

Best Practices For Booting From SAN (BFS) Configurations ......................... 19

Best Practices For Testing the Environment ................................................ 20

Installing the Hardware .................................................................................. 20

▼ To Install the HBA ........................................................................... 21

▼ To Connect the Optical Cables ........................................................... 23

▼ To Install the Ethernet Cables ............................................................. 25

▼ To Apply Power .............................................................................. 25

Testing the Installation ................................................................................... 28

▼ To Verify Proper Installation (Oracle Solaris) ........................................ 28

Contents

▼ To Verify Attached Storage (Oracle Solaris) .......................................... 28

Configuring the HBA for Hot-Plug Operation .................................................... 29

▼ To Configure the HBA for Hot-Plug Operation ...................................... 29

Removing the Hardware ................................................................................. 29

▼ To Prepare the HBA for Removal Using the HBA Attention Button ........... 30

▼ To Prepare the HBA for Hot-Plug Removal (Oracle Solaris) ..................... 30

▼ To Remove the HBA Hardware .......................................................... 31

3 HBA Software Installation ............................................................................. 33

Installing Utilities for Updating the BIOS and Firmware ....................................... 33

▼ To Install Utilities for Updating the BIOS or Firmware: ........................... 34

Installing Diagnostic Software ......................................................................... 34

Diagnostic Support for the Oracle Solaris OS ............................................. 34

Diagnostic Support for All Other Supported Operating Systems ..................... 35

Using the OneCommand Manager CLI for Troubleshooting a Fatal Error ......... 36

Installing Drivers ........................................................................................... 36

Installing Drivers for the Oracle Solaris OS ............................................... 37

▼ Installing Drivers for All Other Supported Operating Systems ................... 37

4 Known Issues ................................................................................................ 39

Server Compatibility Issues ............................................................................. 39

Cannot Detect the HBA on the Sun Blade T6300 System .............................. 39

Cannot Verify the FCode Version of the HBA on the Sun Blade T6300 and

T6320 Systems ..................................................................................... 40

Cannot Boot-From-SAN on the Sun Blade X6250 System ............................ 40

HBA Fails to Properly Disconnect During a Hot-Plug Operation on a Sun

Blade T6320 System .............................................................................. 41

HBA Does Not Correctly Map Ethernet Settings on a Sun Blade X6250

System ................................................................................................. 41

On the Sun Blade X6275 System, Default HBA Settings Do Not Allow Boot-

From-SAN Through FC Ports .................................................................. 42

6 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

Using This Documentation

■

Overview – Describes how to install and remove the StorageTek Dual 8Gb FC Dual GbE

HBA, ExpressModule, Emulex

■

Audience – Technicians, system administrators, and authorized service providers

■

Required knowledge – Advanced experience troubleshooting and replacing hardware

Product Documentation Library

Documentation and resources for this product and related products are available at http://

docs.oracle.com/cd/E19353-01/index.html.

Feedback

Provide feedback about this documentation at http://www.oracle.com/goto/docfeedback.

Using This Documentation 7

8 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

♦ ♦ ♦ C H A P T E R 1

HBA Overview

This chapter provides a basic overview of Oracle's StorageTek Dual 8Gb FC Dual GbE

ExpressModule HBA, which uses Emulex (now Broadcom) technology. This chapter

also describes the various operating systems, host platforms, storage, and infrastructure

configurations that support the HBA.

This chapter contains the following topics:

■

“Kit Contents” on page 9

■

“HBA Features and Specifications” on page 9

■

“Operating System and Technology Requirements” on page 11

■

“System Interoperability” on page 12“System Interoperability” on page 12

■

“Boot Support” on page 15

■

“Environmental Requirements” on page 15

Kit Contents

■

StorageTek Dual 8 Gb FC Dual GbE ExpressModule HBA, Emulex

■

Accessing Documentation document

HBA Features and Specifications

The StorageTek Dual 8 Gb FC Dual GbE HBA (SG-XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-

E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N, and 7105393) consists of a single-

wide, ExpressModule bus expansion board. The board interfaces an eight-lane PCI-Express

bus, with four lanes supporting two Fibre Channel (FC) optical media ports and four lanes

supporting two UTP (copper) Gigabit Ethernet (GbE) ports. The two independent FC ports

operate at 8 Gbit/second and feature 8/4/2 Gbit/second autonegotiation.

Chapter 1 • HBA Overview 9

HBA Features and Specifications

The HBA is also backward compatible with FC ports that operate at 4 and 2 Gbit/second. The

Gigabit Ethernet ports can be configured to operate in 10-, 100-, or 1000-Mbit/second Ethernet

networks.

See Table 1, “HBA Features and Specifications,” on page 10 for a list of the HBA features.

TABLE 1

HBA Features and Specifications

Feature Description

PCI connector x8

PCI signaling environment PCI-Express x8 (8 active lanes)

PCI lane usage FC x4 lanes

GbE x4 lanes

PCI transfer rate (maximum) PCI-Express Generation Two (5 Gbit/second) x8

Number of FC ports Two

Number of devices supported 126 devices per FC loop; 510 devices in Fabric mode

FC bus type (external) Fiber-optic media, short-wave laser, multimode fiber (400‐M5- SN-S)

FC data rates 2.125, 4.25, 8.5 Gbit/second (auto-detected)

FC topologies Switched fabric (N_Port), arbitrated loop (NL_Port) and point-to-point (N_Port)

Number of GbE ports Two

GbE interface type (external) IEEE 802.3 compliant, copper, UTP RJ-45

GbE transfer rate 10/100/1000-Mbit/second per port, autosensing, full-duplex

RAM 1.5 MB, parity protected, per port

BIOS ROM (FC) One 4-MB flash ROM, field-programmable

BIOS ROM (GbE) One 1-MB flash ROM

NVRAM (FC) One 2-KB EEPROM

NVRAM (GbE) One 128-KB EEPROM

External connectors Two Small Form-factor Pluggable (SFP) optics with LC-style connectors and two RJ-45 GbE

connectors

Maximum FC cable length 2 Gbit/second:

500 meters using 50/125 mm core OM3 fiber

300 meters using 50/125 mm core OM2 fiber

150 meters using 50/125 mm core OM1 fiber

150 meters using 62.5/125 mm core fiber

4 Gbit/second:

380 meters using 50/125 mm core OM3 fiber

150 meters using 50/125 mm core OM2 fiber

70 meters using 50/125 mm core OM1 fiber

10 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

Operating System and Technology Requirements

Feature Description

70 meters using 62.5/125 mm core fiber

8 Gbit/second:

150 meters using 50/125 mm core OM3 fiber

50 meters using 50/125 mm core OM2 fiber

21 meters using 62.5/125 mm core OM1 fiber

LED indicators and button Two LEDs per channel (yellow and green) on the front panel as status indicators

(Power LED, Attention LED) and a button on the front panel to support hot-swap functionality

Power dissipation 18.2 watts maximum

Form Factor PCI-Express ExpressModule, single-wide (198 mm x 112 mm x 21 mm)

Operating System and Technology Requirements

The HBA requires the operating system (OS) and technology levels listed in Table 2,

“Supported Operating System/Technology Versions (Minimum) ,” on page 11.

Note - If you need to contact Oracle Support, first verify that you have a supported OS installed

on the host system, and install the latest HBA driver, utility, and firmware versions. Updating

the system and HBA to the latest OS, driver, utility, and firmware versions might address the

issue, preventing the need to contact Oracle Support about an issue that has already been fixed.

TABLE 2

Supported Operating System/Technology Versions (Minimum)

Operating System/Technology Supported Versions (minimum)

Oracle Solaris OS for the x86 (64-bit) platform ■ Oracle Solaris 10 1/13 with patches 149176-02 and 145649-04, at minimum

■ Oracle Solaris 11.1 with SRU 7

To obtain the latest patches and SRUs, go to http://support.oracle.com

Oracle Solaris OS for the SPARC (64-bit) platform ■ Oracle Solaris 10 1/13 with patches 149175-02 and 145648-04, at minimum

■ Oracle Solaris 11.1 with SRU 7

To obtain the latest patches and SRUs, go to http://support.oracle.com

Linux OS ■ Oracle Enterprise Linux 5.9 (Red Hat Compatible Kernel (RHCK) and

Unbreakable Enterprise Kernel (UEK) 2, at minimum)

■ Oracle Linux 6.4 (RHCK and UEK2, at minimum)

■ Red Hat Enterprise Linux 5.9 (64-bit)

■ Red Hat Enterprise Linux 6.4 (64-bit)

■ SUSE Linux Enterprise Server 11 SP2 (32-bit and 64-bit)

Microsoft Windows

OS Standard, Enterprise, and

Datacenter Editions

■ Window Server 2008 R2 including SP1 (64-bit)

Chapter 1 • HBA Overview 11

System Interoperability

Operating System/Technology Supported Versions (minimum)

■ Windows Server 2012

VMware Technology ■ VMware ESX/ESXi 5.0

■ VMware ESX/ESXi 5.1

System Interoperability

This section provides information about selected platforms and storage that are compatible with

the heterogeneous FC network design of the HBA. This section contains the following topics:

■

“Host Platform Support” on page 12

■

“Storage Support” on page 13

■

“Switch Support ” on page 14

■

“Software Support” on page 14

Host Platform Support

The HBA is supported by the platforms and operating systems listed in Table 3, “Platform and

Operating System Support,” on page 12.For up-to-date information, see your server Product

Notes and web pages.

For supported operating system and technology versions, see Table 2, “Supported Operating

System/Technology Versions (Minimum) ,” on page 11.

TABLE 3

Platform and Operating System Support

Platform Supported OS/Technology

Oracle Chassis

Sun Blade 6000 Oracle Solaris

Sun Blade 6048 Oracle Solaris

Oracle SPARC Servers

SPARC T4-1B Oracle Solaris

SPARC T4-4 Oracle Solaris

SPARC T5-1B Oracle Solaris

Sun Blade T6300 Oracle Solaris

Sun Blade T6320 Oracle Solaris

Sun Blade T6340 Oracle Solaris

Oracle x86 Servers

Sun Blade X3-2B Oracle Solaris, Linux, VMware, and Windows

12 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

System Interoperability

Platform Supported OS/Technology

Sun Blade X4-2B Oracle Solaris, Linux, VMware, and Windows

Sun Blade X6220 Oracle Solaris, Linux, VMware, and Windows

Sun Blade X6240 Oracle Solaris, Linux, VMware, and Windows

Sun Blade X6250 Oracle Solaris, Linux, VMware, and Windows

Sun Blade X6270 Oracle Solaris, Linux, VMware, and Windows

Sun Blade X6275 Oracle Solaris, Linux, VMware, and Windows

Sun Blade X6440

†

Oracle Solaris, Linux, VMware, and Windows

Sun Server X2-8 Oracle Solaris, Linux, VMware, and Windows

†

In order for the HBA to support this server, the BIOS version on the server must be later than version 1.17. For information about the

BIOS version installed on the server, go to the server web page.

The system must have an available ExpressModule slot in which you can install the HBA.

Storage Support

This section lists the arrays and tape storage supported by the HBA. This section contains the

following topics:

■

“Array Support” on page 13

■

“Tape Storage Support” on page 13

Array Support

The HBA supports connecting to, using a supported switch, the following arrays:

■

StorageTek 2540

■

StorageTek 6140

■

StorageTek 6540

■

StorageTek 6780

■

StorageTek 9970

■

StorageTek 9980/9985

■

StorageTek 9990

Tape Storage Support

The HBA supports connecting to, using a supported switch, the following tape storage:

■

StorageTek 9970 system

■

StorageTek 9980/9985/9985V system

Chapter 1 • HBA Overview 13

System Interoperability

■

StorageTek 9990/9900V system

■

StorageTek SL24 tape autoloader

■

StorageTek SL48 tape library

■

StorageTek L1400 tape library

■

StorageTek virtual tape library (VTL): VTL Value and VTL Plus

■

StorageTek SL500 modular library

■

StorageTek SL8500 modular library

■

StorageTek SL3000 modular library

■

IBM and HP LTO3 tape drives

■

IBM and HP LTO4 tape drives

■

StorageTek T10000A and T10000Btape drive

■

StorageTek T9840C tape drive

■

StorageTek T9840D tape drive

Switch Support

Note - For technical support issues with any switches, refer to the product documentation or

contact the switch manufacturer.

The HBA supports connecting to any 8 Gb/s Fibre Channel (FC) switch from any vendor that

follows standard FC specifications, with the following considerations:

■

Direct Access Storage for FC is supported with COMSTAR.

Note - This documentation lists switches that are specifically not supported by the HBA, when

applicable.

The NIC portion of this adapter is supported by all 1-Gb Ethernet switches.

Software Support

The HBA is supported by the software applications listed in Table 4, “Software Support ,” on

page 14.

TABLE 4

Software Support

Software (minimum version) Supported OS

Sun Cluster 3.x Oracle Solaris

14 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

Boot Support

Software (minimum version) Supported OS

Sun StorEdge Enterprise Backup Storage 7.2/7.3/7.4 Oracle Solaris

VERITAS NetBackup 5.1/6.x Oracle Solaris

VERITAS Software Foundation (VxSF) 4.1/5.0 Oracle Solaris

VERITAS Cluster 5.0 Oracle Solaris

VERITAS File System 5.0 Oracle Solaris

VERITAS Volume Manager VxVM 5.0 Oracle Solaris

Validation Test Suite (SunVTS) Oracle Solaris

FMA Oracle Solaris

HBAnyware management utility Oracle Solaris, Linux, VMware, and Windows

OneCommand Manager application Oracle Solaris, Linux, and Windows

AutoPilot Installer Windows

Boot Support

The HBA supports booting through the HBA in the following environments:

■

Oracle Solaris 10 01/13 for the x86 and SPARC environments

■

Oracle Solaris 11.1 for the x86 and SPARC environments

■

Preboot Execution Environment (PXE) boot capable (for x86 systems)

■

RHEL 5.9 and 6.4

■

SLES 11 SP2

■

Oracle Enterprise Linux 5.9 and 6.4

■

VMware ESX/ESXi 5.0 and 5.1

■

Windows Server 2008 R2 including SP1

■

Windows Server 2012

Environmental Requirements

The HBA environmental requirements are listed in Table 5, “HBA Environmental

Requirements ,” on page 15.

TABLE 5

HBA Environmental Requirements

Specification Operating Non-Operating

Temperature 0˚C to 40˚C, noncondensing -40˚C to 70˚C, noncondensing

Chapter 1 • HBA Overview 15

Environmental Requirements

Specification Operating Non-Operating

Humidity 10% to 90% relative humidity (RH),

noncondensing

93% RH, noncondensing, 38˚C max wet bulb

Altitude up to 3000 meters 12,000 meters

Vibration 0.20G in all axes, 5-500 Hz sine 1.0G in all axes, 5-500 Hz sine

Shock 5G, 11 ms half-sine 30G 11 ms half-sine

16 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

♦ ♦ ♦ C H A P T E R 2

Hardware Installation and Removal

This chapter describes the tasks required to install and remove the HBA. Refer to your system

installation or service manual for detailed instructions.

This chapter contains the following topics:

■

“Observing ESD and Handling Precautions” on page 17

■

“Best Practices for Installing the HBA” on page 18

■

“Installing the Hardware” on page 20

■

“Configuring the HBA for Hot-Plug Operation” on page 29“Configuring the HBA for

Hot-Plug Operation” on page 29

■

“Removing the Hardware” on page 29

Observing ESD and Handling Precautions

Caution - Damage to the HBA can occur as the result of careless handling or electrostatic

discharge (ESD). Always handle the HBA with care to avoid damage to electrostatic sensitive

components.

To minimize the possibility of ESD-related damage, use both a workstation antistatic mat and

an ESD wrist strap. You can get an ESD wrist strap from any reputable electronics store or

from Sun as part number 250-1007. Observe the following precautions to avoid ESD-related

problems:

■

Leave the HBA in its antistatic bag until you are ready to install it in the system.

■

Always use a properly fitted and grounded wrist strap or other suitable ESD protection

when handling the HBA, and observe proper ESD grounding techniques.

■

Hold the HBA by the edge of the metal canister, not by the connectors.

■

Place the HBA on a properly grounded antistatic work surface pad when it is out of its

protective antistatic bag.

Chapter 2 • Hardware Installation and Removal 17

Best Practices for Installing the HBA

Before installing the HBA into the system, review the best practices in this section to avoid

potential issues:

■

“General Best Practices” on page 18

■

“Best Practices For Switches and Zoning” on page 19

■

“Best Practices For Booting From SAN (BFS) Configurations” on page 19

■

“Best Practices For Testing the Environment” on page 20

General Best Practices

Follow these general best practices for installing and configuring the HBA:

■

Spread the I/O load amongst multiple HBAs and multiple ports to avoid bottlenecks and

promote higher availability.

■

Use fixed link speeds instead of auto-negotiation wherever possible. While the HBA

supports auto-negotiation, auto-negotiation slows things down in the event of a fabric

rebuild.

■

Do not configure both tape devices and disks on the same HBA port, even if using a switch

and zoning.

■

If more than one of a given HBA model is present in the configuration, enable only the

OpROM for the first HBA seen in the boot sequence. There is a limited amount of space for

OpROMs, so do not unnecessarily enable all OpROMs, as space usage issues might occur.

■

When installing the HBA, be sure to also install the latest version (version 11.1.218.x

or newer) of the command-line utility available from the manufacturer's website (See

“Installing Utilities for Updating the BIOS and Firmware” on page 33). Keep the HBA

utilities, firmware, and drivers up-to-date, and update them in that order.

■

After installing the OneCommand Manager CLI utility, ensure that the elxhbamgrd daemon

process is running (The OneCommand Manager utility starts this daemon process, by

default, upon installation.). In the event of a failure, the elxhbamgrd daemon produces a

usable firmware dump for troubleshooting. The location of dump files varies, based on your

operating system:

■

Windows: OneCommandManager-installation-directory\Util\Dump

■

Oracle Solaris: /opt/ELXocm/Dump

■

Linux: /var/log/emulex/ocmanager/Dump

Keep in mind that manual firmware dumps do not collect fatal firmware errors. If the

OneCommand Manager utility is installed and running, the HBA firmware detects a

18 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

Best Practices for Installing the HBA

fatal error, and then notifies the HBA driver of the error. The driver then notifies the

OneCommand Manager utility (via the elxhbamgrd daemon process) to start the firmware

dump. This firmware dump starts automatically, and the dump file is stored in the default

dump location, based on your operating system.

Best Practices For Switches and Zoning

Follow these best practices for switches and zoning in your environment:

■

FC-SW configurations: check with the switch manufacturer for optimal configuration

recommendations, including zoning.

■

Note that FC-AL is not supported at 16Gb/s or faster. Use FC-P2P instead.

■

Use single initiator hard zoning to do the following:

■

Avoid Registered State Change Notification (RSCN) storms.

■

Shield devices from indiscriminate SCSI inquiries.

■

Provide security by avoiding inappropriate access.

■

Use meaningful names for zones, and document the entire configuration.

■

Use only FCP-2 (also called FC-TAPE or FCP Error Recovery) with tape and/or sequential

devices. While FCP-2 might not cause problems for hard disk drives (HDDs), FCP-2 is a

sequence-level error recovery mechanism that is irrelevant to HDDs.

■

If using FC tape backups, place tape ports and backup servers on the same FC switch to

avoid tying up inter-switch links (ISLs).

■

SAN switches can be a major source of disruption if you do not take extreme care with

respect to configuration. Do not perform updates to switch OSes and/or firmware, or enable

new features on SAN switches, until you have first tried the updated switches in a test

configuration. The HBA might not support newer switch features, and switch OS and/or

firmware updates might require changes to, and/or restoration of, switch configuration

settings.

Best Practices For Booting From SAN (BFS)

Configurations

If you plan to install a Boot From SAN (BFS) HBA, follow these best practices:

■

Some devices and operating systems do not yet support UEFI-based BIOS and can boot

only from the Legacy BIOS boot mode. However, many servers with UEFI firmware allow

you to enable a legacy BIOS compatibility mode.

Chapter 2 • Hardware Installation and Removal 19

Installing the Hardware

■

Legacy BIOS issues - many tweaks and patches have been added over the years to resolve

various issues, and not all were done with the larger ecosystem (many different types of

servers, HBAs, OSes, and so on) in mind.

■

Secure Boot (a UEFI-specific feature) can help you control the boot process, preventing

unauthorized code from running.

■

Larger devices (>2TB) require the use of a GUID Partition Table (GPT) instead of a Master

Boot Record (MBR). GPT is the standard for EFI; it can be implemented in legacy BIOSes,

but it is more difficult to set up. So, while you might be able to boot from a >2TB device

in the legacy BIOS, it might not be seamless. If you are dual-booting with an OS that is

already installed in one mode or the other, however, it is good practice to boot in the same

boot mode as the one that is already in use.

■

Disable OpROM and BIOS for all HBA cards except the one connected to the boot device.

■

When installing a Boot From SAN (BFS) HBA, configure a single connection to a single

SAN target/LUN, install the boot OS, and get that working before installing other HBAs

and storage. If the configuration is complex, finding the root cause for any BFS issues

becomes far more complicated.

■

Once BFS is installed and working, make sure the HBA driver and firmware are at the latest

revision levels. If required, configure a multipath connection, and perhaps one or more

alternate boot LUNs.

Best Practices For Testing the Environment

Test the storage environment by doing the following:

■

Boot the OS on the host server, and then disable the primary path to the SAN boot device to

validate the multipath connection.

■

Physically pull the cable from the system.

■

Intentionally disrupt zoning at the FC switch that you plan to attach to the HBA.

■

If you have installed any alternate boot LUNs, try to boot from those (after disrupting the

primary connection(s)).

■

Make sure the boot LUN is set as the first boot device in the system BIOS/UEFI settings.

Installing the Hardware

The hardware installation process involves the following general steps, described in this

section:

■

“To Install the HBA” on page 21

20 StorageTek Dual 8Gb FC Dual GbE HBA, ExpressModule, Emulex Installation Guide For HBA Models SG-

XPCIEFCGBE-E8-Z, SG-PCIEFCGBE-E8-Z, SG-XPCIEFCGBE-E8-N, SG-PCIEFCGBE-E8-N and 7105393 • August

2018

La page est en cours de chargement...

Oracle Sun StorageTek SG-PCIEFCGBE-E8-N Guide d'installation

Marque: Oracle

Modèle: Sun StorageTek SG-PCIEFCGBE-E8-N

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Oracle Sun StorageTek SG-PCIEFCGBE-E8-N Installation guide

Oracle Sun StorageTek SG-PCIEFCGBE-E8-N Guide d'installation

Ce manuel convient également à

Oracle Sun StorageTek SG-PCIEFCGBE-E8-N Guide d'installation

dans d''autres langues

Documents connexes

Autres documents