dB Tech­no­lo­gies SUB 618 Guide de démarrage rapide

Catégorie
Matériel musical
Taper
Guide de démarrage rapide

Ce manuel convient également à

www.dbtechnologies.com info@dbtechnologies-aeb.com
SUB 618 Rev 1.1 cod. 420120252Q
Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO” -
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOGNA (ITALIA)
Tel +39 051 969870 Fax +39 051 969725 www.dbtechnologies.com info@dbtechnologies-aeb.com
www.dbtechnologies.com info@dbtechnologies-aeb.com
SUB 618 Rev 1.1 cod. 420120252Q
Thank you for choosing a dBTechnologies Product!
The new SUB 618 is an active subwoofer. It is equipped with one 18” transducer (2.5” voice coil).
It is portable, thanks to the compact size, low weight and the convenient handles.
It allows a mono or stereo input and output connection, and a complete configuration with different parameters
controls. Thanks to the settings of polarity, low-frequencies enhancement, and of possible crossover filtering in
output, it is possible to use it in different scenarios. A typical configuration is the matching with B-Hype and Opera
series speakers, thanks to the M20 pole mount on the top. The subwoofer is also stackable.
Check the site www.dbtechnologies.com for the complete user manual!
1) Unpacking
The box contains:
N°1 SUB 618
N°1 Mains cable (VDE)
This quick start and warranty documentation
2) Easy installation
SUB 618 is equipped with:
A – Houses for stack mounting
B – M20 pole mount
C – Handles (1 x side)
Those mechanical particulars were thought for an easy
use and for different configuration needs.
In the pictures above are shown two examples of
configuration for the use of SUB 618.
The matching with a speaker (like one of the OPERA or
B-HYPE series) allows a perfect performance in an
extended frequency range. SUB 618 is perfect for
gigging bands, like for small-medium venue
installations. The mechanical houses on the top of the
subwoofer cabinet allow the stacked use.
IT IS MANDATORY TO READ AND FULLY
UNDERSTAND THE COMPLETE USER
MANUAL FOR THE ADMITTED CONFIGURATIONS
OF THE PRODUCT, SAFETY INFORMATION, AND
THE PROPER USE OF ACCESSORIES (IF ANY).
NEVER USE THE HANDLES TO SUSPEND
THE SPEAKER!
www.dbtechnologies.com info@dbtechnologies-aeb.com
SUB 618 Rev 1.1 cod. 420120252Q
3) Connections and controls
All the connections and controls are in the amplifier
panel side:
1 – Balanced XLR inputs
2 – Balanced XLR outputs
3 – Subwoofer level rotary
4 – Outputs Mode (Link or Xover mode)
5 – Subwoofer Setup (Polarity switch) and
Subwoofer Mode button (Flat/Boosted)
6 – LEDs (Limiter, Signal / ON)
7 – Mains input connector
8–Power switch (ON, OFF)
a) Once you have properly set up the desired
configuration (see also the complete user manual and
accessories instructions for further information),
connect the audio input (mono) or inputs (stereo) (1).
Connect the output (mono) or outputs (stereo) (2) and
consequently set the Subwoofer level to 0 dB in the
right position (3).
b) Set properly the Outputs Mode (4), (“Link” in case of
direct link connection, “Xover” in case of 120 Hz
crossover, for example when in use with a OPERA or B-
HYPE series model).
c) Choose the Subwoofer Polarity (Normal or Reverse)
(5) to obtain the proper behavior. It is possible to add
a low-frequencies boost (5) with the related Subwoofer
Mode switch.
d) Connect the VDE cable to the related connector (7).
Then turn ON the power switch (8). The, the
“Signal/ON” LED (6) turns on, signaling the proper
power connection, and starts blinking at the presence
of audio signal (greater than -20 dBu).
Check the site www.dbtechnologies.com for further
information, for added accessories and for the
complete user manual!
www.dbtechnologies.com info@dbtechnologies-aeb.com
SUB 618 Rev 1.1 cod. 420120252Q
Technical Data
Speaker Type: Active subwoofer
Usable Bandwidth [-10 dB]: 35 – 130 Hz
Max SPL (1 m): 133 dB
LF: 18”
LF Voice Coil: 2.5”
Amplifier
Amp Technology: SMPS digital amplifier
Amp Class: Class-D – Passive cooling (convection)
RMS Power: 600 W
Peak Power: 1200 W
Operating voltage
(factory set)
:
220-240V~ (50-60Hz) or
110-120V~ (50-60 Hz)
Processor and user interface
Controller: 28/56 bit DSP
Limiter: Peak, Thermal, RMS
Controls: Subwoofer level, Outputs mode, Polarity,
Subwoofer mode
Inputs / Outputs
Signal Input: 2 x XLR (balanced)
Signal Out: 2 x XLR (balanced)
Mains connections: VDE
Mechanics
Housing: Plywood
Grille: Full metal grille
Pole Mount: Yes, M20
Width: 500 mm (19.69 in)
Height: 625 mm (24.60 in)
Depth: 690 mm (27.17 in)
Weight: 31.1 kg (68.57 lbs.)
Download the complete user manual on: www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
Scan with your QR Reader
App to download the
complete User Manual
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

dB Tech­no­lo­gies SUB 618 Guide de démarrage rapide

Catégorie
Matériel musical
Taper
Guide de démarrage rapide
Ce manuel convient également à