Panasonic SLG700E Mode d'emploi

Catégorie
Lecteur CD
Taper
Mode d'emploi
SL-G700
Network/Super Audio CD Player Basic Operating Instructions
Netzwerk/Super Audio CD Player Kurz-Bedienungsanleitung
Lecteur réseau/Super Audio CD Manuel d’utilisation Fonctions de base
Lettore Super Audio CD e Network Istruzioni per l’uso di base
Netwerk/Super Audio CD-speler Beknopte gebruiksaanwijzing
Reproductor en Red/Super Audio CD Instrucciones básicas
Nätverk/Super Audio CD-spelare Grundläggande bruksanvisning
Netværk/Super Audio CD-afspiller Vejledning i den grundlæggende betjening
Verkko/Super Audio CD-soitin Perusasetukset Käyttöohjeet
Odtwarzacz sieciowy/Super Audio CD Skrócona instrukcja obsługi
02
Music is borderless and timeless, touching people’s
hearts across cultures and generations.
Each day the discovery of a truly emotive experience
from an unencountered sound awaits.
Let us take you on your journey to rediscover music.
(02)
03
Delivering the Ultimate Emotive Musical
Experience to All
At Technics we understand that the listening experience is not
purely about technology but the magical and emotional relationship
between people and music.
We want people to experience music as it was originally intended
and enable them to feel the emotional impact that enthuses and
delights them.
Through delivering this experience we want to support the
development and enjoyment of the worlds many musical cultures.
This is our philosophy.
With a combination of our love of music and the vast high-
end audio experience of the Technics team, we stand committed
to building a brand that provides the ultimate emotive musical
experience by music lovers, for music lovers.
Director
Michiko Ogawa
(03)
04
(04)
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this manual for future use.
About descriptions in these operating instructions
- Pages to be referred to are indicated as “ ○○”.
- The illustrations shown may differ from your unit.
Illustrations and figures in this manual are of the silver main body.
Panasonic Corporation, a company having its registered office of 1006, Oaza Kadoma, Kadoma City,
Osaka 571-8501, Japan, automatically collects personal data such as IP address and/or Device ID from
your device as soon as you connect it to the Internet. We do this to protect our customers and the
integrity of our Service as well as to protect the rights or property of Panasonic.
You have a right of access, rectification and objection to in certain circumstances, a right of erasure,
restriction of processing, data portability and a right to object to other forms of processing. If you wish
to exercise any of the above rights and/or wish to know more about the processing of your personal data
in this context, please refer to the full text of our privacy policy displayed at the support page of your
device, http://panasonic.jp/support/global/cs/audio/, http://www.technics.com/support/ or contact our
customer communications/support number or address described in the Pan European Guarantee included
in your device box to send you the full text of our privacy policy.
Declaration of Conformity (DoC)
Hereby, “Panasonic Corporation” declares that this product is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
Customers can download a copy of the original DoC to our RE products from our DoC server:
http://www.ptc.panasonic.eu
Contact to Authorised Representative:
Panasonic Marketing Europe GmbH, Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,
Germany
Type of wireless Frequency band Maximum Power (EIRP)
WLAN 2412 - 2472 MHz
5180 - 5320 MHz
5500 - 5700 MHz
20 dBm
20 dBm
20 dBm
Bluetooth
®
2402 - 2480 MHz 10 dBm
5.15 - 5.35 GHz band is restricted to indoor operations only in the following countries.
A more detailed operating instruction is available in “Operating Instructions” (PDF format).
To read it, download it from the website.
www.technics.com/support/
You will need Adobe Reader to browse or print “Operating Instructions” (PDF format). You
can download and install a version of Adobe Reader that you can use with your OS from
the following website.
http://www.adobe.com/products/acrobat/readstep2.html
English
05
(05)
Table of contents
Safety precautions 06
Installation 08
Control reference guide 09
Basic
Connections 12
Network settings 13
Playback 17
Licenses 19
Specifications 20
Accessories
AC mains lead (2)
K2CM3YY00041
Except for Switzerland
K2CS3YY00033
For Switzerland
System connection cable (1)
K2KYYYY00233
Analogue audio cable (1)
K2KYYYY00257
Remote control (1)
N2QAYA000143
Batteries for remote control (2)
Product numbers provided in these operating instructions are correct as of April 2019.
These may be subject to change.
Do not use AC mains lead with other equipment.
Using the remote control
2
1
Note
Insert the battery so the terminals (
and ) match those in
the remote control.
Point it at the remote control signal sensor on this unit. ( 09)
Keep the batteries out of reach of children to prevent
swallowing.
R03/LR03, AAA
(Alkaline or manganese batteries)
For the United Kingdom
and Ireland customer
Sales and Support
Information
Customer Communications
Centre
For customers within the UK:
0333 222 8777
For customers within Ireland:
01 447 5229
Monday–Friday 9:00 am –
5:00 pm, (Excluding public
holidays).
For further support on your
product, please visit our
website:
www.technics.com/uk/
06
Safety precautions
(06)
Warning
Unit
To reduce the risk of fire, electric shock or
product damage,
- Do not expose this unit to rain, moisture,
dripping or splashing.
- Do not place objects filled with liquids, such
as vases, on this unit.
- Use the recommended accessories.
- Do not remove covers.
- Do not repair this unit by yourself. Refer
servicing to qualified service personnel.
- Do not let metal objects fall inside this unit.
- Do not place heavy items on this unit.
AC mains lead
To reduce the risk of fire, electric shock or
product damage,
- Ensure that the power supply voltage
corresponds to the voltage printed on this
unit.
- Insert the mains plug fully into the socket
outlet.
- Do not pull, bend, or place heavy items on the
lead.
- Do not handle the plug with wet hands.
- Hold onto the mains plug body when
disconnecting the plug.
- Do not use a damaged mains plug or socket
outlet.
The mains plug is the disconnecting device.
Install this unit so that the mains plug can be
unplugged from the socket outlet immediately.
Ensure the earth pin on the mains plug is
securely connected to prevent electrical shock.
- An apparatus with CLASS I construction shall
be connected to a mains socket outlet with a
protective earth connection.
Caution
Unit
Do not place sources of naked flames, such as
lighted candles, on this unit.
This unit may receive radio interference caused
by mobile telephones during use. If such
interference occurs, please increase separation
between this unit and the mobile telephone.
This unit is intended for use in moderate and
tropical climates.
Do not put any objects on this unit. This unit
becomes hot while it is on.
This unit utilizes a laser. Use of controls or
adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
Placement
Place this unit on an even surface.
To reduce the risk of fire, electric shock or
product damage,
- Do not install or place this unit in a bookcase,
built-in cabinet or in another confined space.
Ensure this unit is well ventilated.
- Do not expose this unit to direct sunlight, high
temperatures, high humidity, and excessive
vibration.
Do not lift or carry this unit by holding the
knobs or antenna. Doing so may cause this
unit to fall, resulting in personal injury or
malfunction of this unit.
Battery
Danger of explosion if battery is incorrectly
replaced. Replace only with the type
recommended by the manufacturer.
Mishandling of batteries can cause electrolyte
leakage and may cause a fire.
- Remove the battery if you do not intend to
use the remote control for a long period of
time. Store in a cool, dark place.
- Do not heat or expose to flame.
- Do not leave the battery(ies) in a car exposed
to direct sunlight for a long period of time
with doors and windows closed.
- Do not take apart or short circuit.
- Do not recharge alkaline or manganese
batteries.
- Do not use batteries if the covering has been
peeled off.
- Do not mix old and new batteries or different
types at the same time.
When disposing of the batteries, please contact
your local authorities or dealer and ask for the
correct method of disposal.
(Back of product)
(Inside of product)
(Produktets innside)
English
07
(07)
For the United Kingdom and Ireland
customer
Caution for AC Mains Lead
(For the AC mains plug of three pins)
For your safety, please read the following text
carefully.
This appliance is supplied with a moulded three
pin mains plug for your safety and convenience.
A 10-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please
ensure that the replacement fuse has a rating of
10-ampere and that it is approved by ASTA or
BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover you
must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be
used until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local dealer.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to
the type of AC mains plug (figures A and B).
Confirm the AC mains plug fitted and follow the
instructions below. Illustrations may differ from
actual AC mains plug.
1. Open the fuse cover with a screwdriver.
Figure A Figure B
Fuse cover
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household
waste.
For proper treatment, recovery and recycling of old products and used batteries, please take
them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol):
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
2.
Replace the fuse and close or attach the fuse cover.
Figure A Figure B
Fuse
(10 ampere)
Fuse
(10 ampere)
NORSK
ADVARSEL
Produkt
For å redusere faren for brann, elektrisk støt eller
skade på apparatet :
- Utsett ikke produktet for regn, fukt, drypping
eller sprut.
- Ikke plasser objekter som er fylt med væske,
som vaser, på apparatet.
- Bruk anbefalt tilbehør.
- Fjern ikke deksler.
- Reparer ikke denne enheten selv, overlat service
til kvalifisert servicepersonell.
Vekselstrømnett
Nettspselet er trukket ut fra denne enheten.
Installer denne enheten slik at nettstøpselet
umiddelbart kan trekkes fra stikkontakten.
FORSIKTIG
Produkt
Dette produktet anvender en laser. Betjening av
kontroller eller justering eller andre inngrep enn de
beskrevet i denne bruksanvisning kan føre til farlig
bestråling.
Plasser ikke åpen ild, slik som levende lys, oppå
apparatet.
Denne enheten er beregnet for bruk i moderate
og tropiske klimaer.
Plassering
For å redusere faren for brann, elektrisk støt eller
skade på apparatet :
- Ikke plasser apparatet i en bokhylle, et
innebygget kabinett eller et annet lukket sted.
Pass på at produktet er godt ventilert.
08
Installation
(08)
Installation
Turn off all the equipment before connection and
read the appropriate operating instructions. Be
sure to raise this unit when moving, and do not
drag this unit.
Unit care
Pull out the AC mains lead from the socket
before maintenance. Clean this unit with a soft
cloth.
When dirt is heavy, wring a wet cloth tightly to
wipe the dirt, and then wipe it with a soft cloth.
Do not use solvents including benzine, thinner,
alcohol, kitchen detergent, chemical wiper, etc.
Doing so may cause the exterior case to be
deformed or the coating to come off.
Using “Technics Audio Center”
If you install the dedicated app “Technics
Audio Center” (free of charge) on your tablet/
smartphone, you can stream music files from the
device on your network to this unit and configure
the settings of sound quality, etc.
For details, visit:
www.technics.com/support/
Firmware updates
Occasionally, Panasonic may release updated
firmware for this unit that may add or improve
the way a feature operates. These updates are
available free of charge.
For the update information, refer to the
following website.
www.technics.com/support/firmware/
To dispose of or transfer this unit
Before disposing of or transferring this unit, be
sure to erase all the recorded information by
restoring the settings to factory default.
Press [NWP] or [CD] while this unit is turned
on.
Press [SETUP].
Press [ ], [ ] repeatedly to select
“Initialization” and then press [OK].
Press [ ], [ ] to select “Yes” and then press
[OK].
A confirmation screen appears. Select “Yes”
in the following steps to restore all the
settings to defaults.
Press [ ], [ ] to select “Yes” and then press
[OK] again.
Before you dispose of or transfer this unit
to a third party, be sure to log out of your
music streaming services accounts to prevent
unauthorised use of your accounts.
English
09
(09)
Control reference guide


 
    
01 [ ] Standby/on button
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the
unit is still consuming a small amount of
power.
02 Power indicator
Blue: The unit is on.
Red: The unit is in standby mode.
Off: The unit is off.
03 Headphones jack
Excessive sound pressure from earphones
and headphones can cause hearing loss.
Listening at full volume for long periods
may damage the user’s ears.
04 USB-A terminal (USB Front)
(DC 5 V
500 mA)
You can connect a USB device to the unit
and play back music stored on the USB
device. ( 18)
You can connect the USB flash memory
with new firmware and update the
firmware for this unit.
For details, refer to the following website.
www.technics.com/support/firmware/
05 Remote control signal sensor
Reception distance:
Within approx. 7 m directly in front
Reception angle:
Approx. 30° left and right
06 Disc tray
( 17)
07 Display
Input source, playback status, etc. are
displayed.
08 [
] Open or close the disc tray
09 Playback operation buttons
(e.g. “CD”)
Stop [ ]
Play/Pause
[
]
Press again to resume.
Skip [
] [ ]
Search
Press and hold [
] or
[
].
10 Multi-control knob
Turn this knob clockwise or anticlockwise
to switch the input source and scroll
through items.
To set an item, press the knob; to enter the
setup screen, press and hold it.
11 Input selector button
Switch the input source.
12 Headphone volume button
Headphone volume is displayed. (Volume
can be adjusted with the multi-control
knob while displaying.)
-- dB (min), -99.0 dB to 0 dB (max)
This unit (front)
10
Control reference guide (Continued)
(10)



  
  
01 Analogue audio output terminals
(ANALOG OUT)
You can connect the pre-amplifier which
has the unbalanced input terminals, etc.
with analogue audio cable (supplied) to
output the analogue audio signals.
You can connect the pre-amplifier which
has the balanced input terminals, etc. with
XLR cable (not supplied).
02 Wireless LAN antenna
( 14)
03 Optical digital output terminal (OPT)
You can connect a digital audio output
device such as D/A converter, etc. with
optical digital audio cable (not supplied) and
play back music.
04 Coaxial digital output terminal (COAX)
You can connect a digital audio output
device such as D/A converter, etc. with
coaxial digital cable (not supplied) and play
back music.
05 Optical digital input terminal (OPT)
You can connect a digital audio output
device with optical digital audio cable (not
supplied) and play back music.
The digital audio input terminals of this unit
can only detect the following linear PCM
signals. For details, refer to the operating
instructions of the connected device.
- Sampling frequency:
32/44.1/48/88.2/96 kHz
- Number of quantisation bits:
16/24 bit
This unit (rear)
06 Coaxial digital input terminal (COAX)
You can connect a digital audio output
device with coaxial digital cable (not
supplied) to this unit and play back music.
The digital audio input terminals of this unit
can only detect the following linear PCM
signals. For details, refer to the operating
instructions of the connected device.
- Sampling frequency:
32/44.1/48/88.2/96/176.4/192 kHz
- Number of quantisation bits:
16/24 bit
07 Product identification marking
The model number is indicated.
08 LAN terminal
( 13)
09 USB-A terminal (USB Rear)
(DC 5 V
1 A)
You can connect a USB HDD to the unit and
play back music stored on the USB HDD.
( 18)
10 System terminal (CONTROL)
11 AC IN terminal ( )
( 12)
11
English
(11)
01 [NWP ]/[CD ]: Standby/on button
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the
unit is still consuming a small amount of
power.
The input source also switches for each
(switches to the last selected input source
when [NWP
]).
02 [NWP]/[CD]: Select the device to be
operated
The playing layer switches by pressing [CD]
while the playback stops for Hybrid Super
Audio CD (SACD).
Press and hold [CD] to switch to “Pure Disc
Playback” mode. ( 18)
03 [>INPUT<]: Switch the input source
04 [DIMMER]: Adjust the brightness of the
power indicator, display, etc.
*
2
Press repeatedly to switch the brightness.
Remote control



















05 [INFO]: View content information
*
1
06 [ ], [ ], [ ], [ ]/[OK]: Selection/OK
*
1
07 [RETURN]: Return to the previous
display
*
1
08 [DIRECT]: Turn on/off Direct mode
09 [RE-MASTER]: Turn on/off Re-master
Press and hold [RE-MASTER] for approx.
2 seconds so that “MQA Decoding : On” is
displayed and the MQA decoding function
will be set to “On”. (Press and hold for
approx. 2 seconds again to set the function
to “Off”.)
10 [MENU]: Enter menu
*
1
11 [SETUP]: Enter setup menu
*
1
12 Adjust the volume
*
2
13 Mute the sound
*
2
14 Playback control buttons ( 17)
15 Numeric buttons, etc.
To enter 2 digits or more
Example:
16: [
10] > [1] > [6]
124: [
10] > [ 10] > [1] > [2] > [4]
[CLEAR]: Clear the entered value.
*
1: Press [NWP]/[CD] first to operate this unit.
(The remote control works only for the
devices supporting system control function
when pressing [AMP].)
*
2: Also works for the devices supporting system
control function.
Buttons that work for Technics devices
supporting system control function
The remote control of this unit also works for
Technics devices supporting system control
function (Stereo Integrated Amplifier, etc.). For
information on the operations of the devices,
please also refer to their operating instructions.
01
[ ] Standby/on button
02
Select the device to be operated
03
Select the input source
04
Measure the output signal when speakers
are connected, and correct its output
12
Connections
(12)
Basic
Connecting to an amplifier
XLR cable
*
(not supplied)
Analogue audio
cable (supplied)
Amplifier
(AV receiver, control amplifier, etc.)
Pre-amplifier with
unbalanced input
terminals
Pre-amplifier with
balanced input
terminals
*
: We recommend using cables with a length of
3 m or less.
For details, refer to the operating instructions of
the connected device.
Do not use any other analogue audio cables
except the supplied one.
Connecting to a digital audio output
device
Digital audio output device
Optical digital
audio cable
(not supplied)
Coaxial digital
cable
(not supplied)
Audio signal of Super Audio CD and Super
Audio CD layer of Hybrid Super Audio CD
cannot be output from the digital audio output
terminal of this unit. Connect the device to the
analogue audio output terminal.
When enjoying video contents with this
function, the video and audio output may not
be synchronised.
For details, refer to the operating instructions of
the connected device.
AC mains lead connection
Connect only after all other connections are
completed.
AC mains lead
(supplied)
To a household
mains socket
Use only the supplied AC mains lead.
Insert the plugs of the cables to be connected
all the way in.
Do not bend cables at sharp angles.
“Wi-Fi” function switching screen is displayed
following “Wi-Fi Setup” when this unit is turned
on. If you stop the Wi-Fi setting, set to “Off
and press [OK]. To keep the Wi-Fi setting, start
the “Google Home” app and follow the on-
screen instructions. ( 13, 14)
Note
This unit consumes a small amount of AC power
( 20) even when the unit is in standby mode.
Remove the plug from the main electrical outlet
if you will not be using the unit for an extended
period of time. Place the unit so the plug can be
easily removed.
13
English
(13)
Network settings
Basic
You can stream online music services or music files from your smartphone/tablet to
this unit. To use these features, this system must join the same internet-connected
network as the compatible device.
This unit can be connected to a router using a LAN cable or built-in Wi-Fi
®
.
For a stable connection to the network, a wired LAN connection is recommended.
Preparation
If you install the “Google Home” app on your
smartphone/tablet, you can set up a connection
using the application.
When using the Chromecast-enabled apps to
play music on this unit, set up a connection
using the “Google Home” app.
Make sure that the Wi-Fi function and
Bluetooth
®
feature are activated on your
smartphones/tablet.
1 Install the “Google Home” app on
your smartphone/tablet.
To download the “Google Home” app, visit:
https://www.google.com/cast/setup/
2 Connect your smartphone/tablet to
the same network as this unit before
setting.
Make sure that the network is connected to
the Internet.
Note
If this unit is used exclusively for the playback
of CDs by disabling the network functions, etc.,
the network setting is not necessary. ( 18)
Wired LAN connection
Broadband router, etc.
LAN cable
(not supplied)
1 Disconnect the AC mains lead.
2 Connect this unit to a broadband
router, etc. using a LAN cable.
3 Connect the AC mains lead to this unit.
( 12)
4 Press [NWP ]/[CD ] to turn this
unit on.
5 Make sure to set up a connection
using “Google Home” app on your
smartphone/tablet.
When the connection is established, “ ” is
displayed.
14
Network settings (Continued)
(14)
Basic
Note
While the AC mains lead is disconnected, the
LAN cable must be connected or disconnected.
Use category 7 or above straight LAN cables
(STP) when connecting to peripheral devices.
Inserting any cable other than a LAN cable in
the LAN port can damage the unit.
After turning on this unit, it may take some time
until this unit is activated.
After the network connection is set up,
“Updating” may be displayed and the firmware
for this unit may be updated.
- After the update has finished successfully and
“Success” is displayed, turn this unit off and
then on.
Even when the Wi-Fi function is set to “On, the
wired LAN function is activated while a LAN
cable being connected. (“
” is displayed.)
Wireless LAN connection
Preparation
Disconnect the AC mains lead.
Disconnect the LAN cable.
Place this unit as close to the wireless router as
possible.
Point up the antenna on the rear of this unit as
shown in the figure.
Connect the AC mains lead to this unit. ( 12)
Note
Do not perform the following:
- Applying too much force to the antenna
- Carrying this unit by holding the antenna
After turning on this unit, it may take some time
until this unit is activated.
After the network connection is set up,
“Updating” may be displayed and the firmware
for this unit may be updated.
- After the update has finished successfully and
“Success” is displayed, turn this unit off and
then on.
The setting will be cancelled after the set time
limit. In that case, try the setting again.
” blinks while the network setting is not
complete, and blinking stops after the Wi-Fi
setting is complete.
While “
” is blinking, the network setting
from “Google Home” may be available. Start
the “Google Home” app and follow the on-
screen instructions.
To cancel this setting in the middle, press [
] or
turn the unit to standby mode.
Network setting for the first time using
the “Google Home” app
1 Press [NWP
]/[CD ] to turn this
unit on.
“Wi-Fi Setup” is displayed.
2 Press [ ], [ ] to select “On” and press
[OK] on the “Wi-Fi” screen.
(It enables the Wi-Fi function)
3 Start the “Google Home” app and
follow the on-screen instructions.
Note
This unit will be displayed as “Technics-
SL-G700-
****
” if the device name is not set.
(“
****
” stands for characters unique to each
set.)
You can check your network information (SSID,
MAC address and IP address) from the “Google
Home” app or “Technics Audio Center” app.
Some items on the “Google Home” app are
irrelevant to this unit.
To cancel this setting in the middle, press [
] or
turn the unit to standby mode.
When this unit is switched to standby mode and
turned on before the Wi-Fi setting is complete,
“Wi-Fi Setup” is displayed. Perform the Wi-Fi
setting or select “Off.
For other connection methods (15)
15
English
(15)
Basic
Setting the network from the setup menu
(When not using the Chromecast-enabled
apps with this unit)
Using the WPS button
“WPS
If your wireless router supports WPS, you can set
up a connection by pressing the WPS button.
A compatible wireless router may have the WPS
identifier mark.
Complete the settings within 2 minutes while
“WPS” is displayed.
When “Wi-Fi Setup” is displayed when turning
on this unit, press [
] to cancel the network
setting and start the setting again.
1 Press [NWP] or [CD].
2 Press [SETUP].
3 Press [ ], [ ] repeatedly to select
“Network” and then press [OK].
When “Wi-Fi” screen is displayed, press [OK].
4 Press [ ], [ ] to select “On” and then
press [OK]. (The wireless LAN function
is enabled.)
5 Press [ ], [ ] to select “WPS Push
and then press [OK].
“WPS” blinks. Complete step 6 within
2 minutes.
6 After “WPS” is displayed, press the
WPS button on the wireless router.
Example:
“Linking” blinks.
When the connection is established,
“Success” is displayed.
- “Fail” may be displayed if the connection
was not complete. Try this method again
from the setup menu. If “Fail” is still
displayed, try other methods.
7 Press [OK] to exit the setting.
Using the WPS PIN code
“WPS PIN”
If your wireless router supports WPS, you can set
up a connection by entering the WPS PIN code.
For details on how to enter the PIN code, refer
to the operating instructions of the wireless
router.
Complete the settings within 2 minutes while
“WPS PIN” and the PIN code are displayed.
When “Wi-Fi Setup” is displayed when turning
on this unit, press [
] to cancel the network
setting and start the setting again.
1 Press [NWP] or [CD].
2 Press [SETUP].
3 Press [
], [ ] repeatedly to select
“Network” and then press [OK].
When “Wi-Fi” screen is displayed, press [OK].
4 Press [ ], [ ] to select “On” and then
press [OK]. (The wireless LAN function
is enabled.)
5 Press [
], [ ] to select “WPS PIN” and
then press [OK].
The PIN code is displayed. Complete step 6
within 2 minutes.
6 Enter the PIN code into the wireless
router from PC, etc.
“Linking” blinks.
When the connection is established,
“Success” is displayed.
- “Fail” may be displayed if the connection
was not complete. Try this method again
from the setup menu. If “Fail” is still
displayed, try other methods.
7 Press [OK] to exit the setting.
Note
Depending on a router, other connected
devices may temporarily lose their connection.
For details, refer to the operating instructions of
the wireless router.
16
Network settings (Continued)
(16)
Basic
Setting the network from the setup menu
(When using the Chromecast-enabled
apps with this unit)
Using the “Google Home” app
“Wi-Fi Setup
When using the Chromecast-enabled apps to
play music on this unit, you need to set up a
network connection using “Google Home” app.
When the network has been set up with another
method, try the setting again with the following
procedure.
When “Wi-Fi Setup” is displayed when turning
on this unit, press [
] to cancel the network
setting and start the setting again.
1 Press [NWP] or [CD].
2 Press [SETUP].
3 Press [
], [ ] repeatedly to select
“Network” and then press [OK].
When “Wi-Fi” screen is displayed, press [OK].
4 Press [ ], [ ] to select “On” and then
press [OK]. (The wireless LAN function
is enabled.)
5 Press [ ], [ ] to select “Wi-Fi Setup
and then press [OK].
“Setting” is displayed.
6 Start the app and follow the on-screen
instructions.
When the connection is established,
“Success” is displayed.
- “Fail” may be displayed if the connection
was not complete. Try this method again
from the setup menu. If “Fail” is still
displayed, try other methods.
7 Press [OK] to exit the setting.
This unit will be displayed as “Technics-
SL-G700-
****
” if the device name is not set.
(“
****
” stands for characters unique to each
set.)
You can check your network information
(SSID, MAC address and IP address) from
the “Google Home” app or “Technics Audio
Center” app.
Some items on the “Google Home” app are
irrelevant to this unit.
Streaming music over the network
This unit is compatible with Chromecast-enabled
apps. For detailed information of Chromecast-
enabled apps, visit:
g.co/cast/apps
You can also stream music files from the device
on your network to this unit by using the free
app “Technics Audio Center”. Download and
install the app from the website below.
www.technics.com/support/
Preparation
Complete the network settings. ( 13)
(Make sure that the network is connected to
the Internet.)
Install the supported application on your device.
Connect the device to the network currently
used at home.
1 Start the Chromecast-enabled app or
“Technics Audio Center” app on your
device (smartphone, tablet, etc.), and
select this unit as the output speaker.
2 Play back the music.
Not all music streaming services are available
in all countries/regions. Registration/
subscription may be required, or fees may
be charged to use music streaming services.
Services are subject to change or be
discontinued. For details, visit an individual
music streaming service’s website.
Important notice:
Before you dispose of or transfer this unit
to a third party, be sure to log out of your
music streaming services accounts to prevent
unauthorised use of your accounts.
17
English
Playback
(17)
Basic
Playing back CD/SACD
1 Press [NWP ]/[CD ] to turn this
unit on.
2 Press [ ] on the unit to open the disc
tray and insert a CD.
Place label up in the proper position in the
middle of the disc tray.
DO DO NOT
12 cm CD
DO
DO
NOT
DO DO NOT
8 cm CD
DO
DO
NOT
Press [ ] again to close the disc tray.
3 Press [ ].
Note
Be careful not to get your finger caught in the
disc tray when opening/closing it.
Repeat Playback
Press [CD].
Press [ ].
“1
”:
Only plays the selected track.
”:
All tracks are repeated.
Random playback
Press [CD].
Press [RND].
Press again to cancel.
Programme playback
Press [CD].
Press [PGM] in the stop mode.
“Program Mode” screen is displayed.
Press the numeric buttons to select tracks.
Repeat this step to make further selections.
Press [ ] to start playback.
Press [
] or [ ] in the stop mode to check the
programmed order.
Press [CLEAR] in the stop mode to clear the
last track.
Press [PGM] in the stop mode to cancel the
programme mode, and the programme
memory will be stored.
Press [
] in the stop mode and select “Yes”
to cancel the programme mode. (The
programme memory will be cleared.)
Note
The programme memory will be cleared in the
following conditions.
- When turning on/off this unit
- when replacing the CD
- when switching the layer
The programme mode is cancelled when the
random playback is set.
Playing back Hybrid Super Audio CDs
Hybrid Super Audio CD discs include a
conventional CD layer along with the Super
Audio CD layer. Although Super Audio CD layer
is preferentially played back, you can select the
CD layer or Super Audio CD layer for playback by
pressing [CD] while the playback stops.
Note
The layer cannot be selected on the disc except
Hybrid Super Audio CD discs.
Decoding MQA-CD
This unit includes the MQA (Master Quality
Authenticated) technology, which enables
playback of MQA audio files and streams,
delivering the sound of the original master
recording.
To deliver the master quality audio of an MQA-
CD, MQA decoding function needs to be set
to “On”. Switch the MQA decoding function to
“On” or “Off” in the following steps.
The default setting is “Off.
Press and hold [RE-MASTER] for approx.
2 seconds or longer.
“MQA Decoding : On” is displayed and the
MQA decoding function is set to “On”. (Press
and hold for approx. 2 seconds again to set
the function to “Off”.)
Play back the MQA-CD.
Compatible CD
A disc with the CD Logo.
This unit can play back discs that conform to
the CD-DA format.
The unit may not be able to play some discs due
to the condition of the recording.
Before playback, finalise the disc on the device
it was recorded on.
CDs that cannot be used
CDs with irregular shapes, such as heart shapes
(Use of such CDs may cause malfunction.)
18
(18)
Playback (Continued)
Basic
CDs that are not guaranteed to operate
with this unit
Discs with illegally copied data and those that
do not conform to industry standards
DualDiscs (Discs that record data such as music
and images on both sides)
Disc formats supported by this unit
Super Audio CD (SACD)
Support
(2-channel only)
Commercially available CDs
(CD-DA)
Support
CD-R/CD-RW (CD-DA) Support
This units lens
Use the lens cleaner (not supplied) to clean the
units lens.
Clean discs
DO
DO NOT
Wipe with a damp cloth and then wipe dry with
a dry cloth.
Disc handling precautions
Handle discs by the edges to avoid inadvertent
scratches or fingerprints on the disc.
Do not attach labels or stickers to discs.
Do not use disc cleaning sprays, benzine,
thinner, static electricity prevention liquids or
any other solvent.
Do not use the following discs:
- Discs with exposed adhesive from removed
stickers or labels (rented discs, etc.).
- Discs that are badly warped or cracked.
- Irregularly shaped discs, such as heart shapes.
Incorrect display or play does not start.
Make sure that the disc is compatible with this
unit.
There is moisture on the lens. Wait for about an
hour and then try again.
Unfinalised CD-R and CD-RW cannot be played
back.
Playback takes time to start.
It may take some time for the disc to load if
there are a lot of tracks on it.
Pure Disc Playback
By disabling the network functions, etc. and this
unit operates exclusively for the playback of CD/
SACD for the higher quality sound.
Press [CD] for 5 seconds or longer.
A confirmation screen appears.
Press [OK].
Press [ ], [ ] to select “Yes” and then
press [OK].
Playback of the online music streaming services,
music files from network devices, etc. cannot be
available while “Pure Disc Playback” is enabled.
Note
Operating from “Technics Audio Center” app,
etc. are not available after setting.
The programme playback cannot be set.
Press again for 5 seconds or longer to cancel
and return to the normal mode.
Playing back music stored on the
USB device
Connect a USB device to the USB-A terminal
(USB Front) on the front of this unit. ( 09)
Press [NWP] or [CD].
Press [>INPUT<] repeatedly to select “USB
Front”.
Press [ ], [ ] to select an item and then press
[OK].
Repeat this step to make further selections.
Press [RETURN] to return to the previous
folder.
Random/repeat playback can be set. ( 17)
When using a USB HDD with this unit,
connect a USB HDD to the USB-A terminal
(USB Rear) on the rear of this unit.
Using Bluetooth
®
You can listen to the sound from the Bluetooth
®
audio device from this unit wirelessly.
Pairing a Bluetooth
®
device
Turn on the Bluetooth
®
feature of the device and
place the device near this unit. (If a Bluetooth
®
device is already connected, disconnect it.)
Press [NWP] or [CD].
Press [>INPUT<] repeatedly to select
“Bluetooth”.
Press [MENU].
Press [ ], [ ] repeatedly to select “Pairing
and then press [OK].
Press [ ], [ ] to select “Yes” and then press
[OK].
“Pairing” is displayed, and this unit waits for
registering.
Select “Technics-SL-G700-
****
” from the
Bluetooth
®
device’s menu.
If the device name is set on the “Google
Home” app, the set name is displayed.
19
English
Licenses
(19)
The Wi-Fi CERTIFIED Logo is a certification
mark of Wi-Fi Alliance
®
.
The Wi-Fi Protected Setup Logo is a
certification mark of Wi-Fi Alliance
®
.
Use of the Works with Apple badge means
that an accessory has been designed to work
specifically with the technology identified
in the badge and has been certified by
the developer to meet Apple performance
standards.
Apple, and AirPlay are trademarks of Apple
Inc., registered in the U.S. and other countries.
This product is compatible with AirPlay 2. iOS
11.4 or later is required.
Google, Google Home, Google Play, Android,
Chromecast built-in and other related marks
and logos are trademarks of Google Inc.
Windows is a trademark or a registered
trademark of Microsoft Corporation in the
United States and other countries.
Windows Media and the Windows logo
are trademarks or registered trademarks
of Microsoft Corporation in the United
States and/or other countries. This product
is protected by certain intellectual property
rights of Microsoft Corporation and third
parties. Use or distribution of such technology
outside of this product is prohibited without
a license from Microsoft or an authorized
Microsoft subsidiary and third parties.
Mac and OS X are trademarks of Apple Inc.,
registered in the U.S. and other countries.
The Bluetooth
®
word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
Panasonic Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
Super Audio CD is a registered trademark.
SBM Direct is a registered trademark.
DSD is a trademark of Sony Corporation.
FLAC Decoder
Copyright (C) 2000, 2001, 2002, 2003, 2004,
2005, 2006, 2007, 2008, 2009 Josh Coalson
Redistribution and use in source and binary
forms, with or without modification, are
permitted provided that the following
conditions are met:
- Redistributions of source code must retain
the above copyright notice, this list of
conditions and the following disclaimer.
- Redistributions in binary form must
reproduce the above copyright notice, this
list of conditions and the following disclaimer
in the documentation and/or other materials
provided with the distribution.
- Neither the name of the Xiph.org Foundation
nor the names of its contributors may be
used to endorse or promote products derived
from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS
AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE FOUNDATION
OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The Spotify Software is subject to third party
licenses found here: https://www.spotify.com/
connect/third-party-licenses.
The MQA logo is a trademark of MQA Limited.
© MQA Limited 2017
20
Specifications
(20)
GENERAL
Power supply
AC 220 V to 240 V,
50/60 Hz
Power
consumption
38 W
Power
consumption in
standby mode
(Network Standby
Off)
Approx. 0.3 W
Power
consumption in
standby mode
(Network Standby
On with Wired
LAN)
Approx. 1.9 W
Power
consumption in
standby mode
(Network Standby
On with Wireless
LAN)
Approx. 1.7 W
Dimensions
(W×H×D)
430 mm × 98 mm ×
407 mm
Mass Approx. 12.2 kg
Operating
temperature range
5 °C to 35 °C
Operating humidity
range
35% to 80% RH
(no condensation)
ANALOG OUTPUT SECTION
Channel 2 ch
Output level
BALANCED
2.0 Vrms (Super Audio CD) /
2.3 Vrms (CD)
UNBALANCED
2.0 Vrms (Super Audio CD) /
2.3 Vrms (CD)
Frequency
response
Super Audio CD 2 Hz to 50 kHz (-3 dB)
CD 2 Hz to 20 kHz (-3 dB)
THD+N
Super Audio CD 0.0006% (1 kHz, 0 dB)
CD 0.0015% (1 kHz, 0 dB)
S/N (IHF-A)
Super Audio CD
BALANCED: 121 dB
UNBALANCED: 118 dB
CD
BALANCED: 121 dB
UNBALANCED: 118 dB
Dynamic range
(IHF-A)
Super Audio CD
BALANCED: 118 dB
UNBALANCED: 115 dB
CD
BALANCED: 98 dB
UNBALANCED: 98 dB
DISC SECTION
Disc played
(8 cm or 12 cm)
Super Audio CD (2ch area
only), CD, CD-R, CD-RW
Pick up
Wavelength
650 nm (Super Audio CD),
790 nm (CD)
Laser power CLASS 1
Audio Output
(Disc)
2ch (FLFR)
Format Super Audio CD, CD-DA
NORSK
Bølgelengde
650 nm (Super Audio CD),
790 nm (CD)
Laserstyrke
Ingen farlig stråling sendes ut
Bluetooth
®
SECTION
Bluetooth
®
system
specification
Bluetooth
®
Ver.4.2
Wireless
equipment
classification
Class 2 (2.5 mW)
Supported profiles A2DP, AVRCP
Supported codec AAC, SBC
Frequency band 2.4 GHz band FH-SS
Operating distance Approx. 10 m Line of sight
*
1
*
1: Prospective communication distance
Measurement environment:
Temperature 25 °C/Height 1.0 m
Measure in “Mode 1
TERMINALS SECTION
Headphones Jack
Stereo, 6.3 mm
110 mW, 32 (VOL MAX)
USB (Front/Rear)
Type A Connecter
USB 2.0 High Speed
DC 5 V 500 mA (Front)
DC 5 V 1 A (Rear)
USB Mass Storage Class
File system FAT16, FAT32, NTFS
Ethernet interface
LAN
(100BASE-TX/10BASE-T)
Digital Input
Optical digital
input
Optical terminal
Coaxial digital
input
Pin jack
Format support LPCM
Analog output
BALANCED 3 pin XLR
UNBALANCED Pin jack
Digital output
Optical digital
output
Optical terminal
Coaxial digital
output
Pin jack
Format support LPCM
System port
System control  3.5 mm, Jack
FORMAT SECTION
USB-A
USB Standard
USB 2.0 high-speed
USB Mass Storage class
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188

Panasonic SLG700E Mode d'emploi

Catégorie
Lecteur CD
Taper
Mode d'emploi