Wacker Neuson PSW31500 Manuel utilisateur

Pump

PS2 800

PSA2 800

PSW3 1500

OPERATOR’S MANUAL

0176745en 001

0209

0176745EN

Foreword

wc_tx001080gb.fm 3

Foreword

Machines covered in this manual

This manual provides information and procedures to safely operate

and maintain this Wacker Neuson model. For your own safety and

protection from injury, carefully read, understand and observe the

safety instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker Neuson

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Neuson

Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Neuson Corporation

reserves the right to change any portion of this information without

notice.

All rights, especially copying and distribution rights, are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker

Neuson Corporation represents an infringement of valid copyrights

and will be prosecuted. We expressly reserve the right to make

technical modifications, even without due notice, which aim at

improving our machines or their safety standards.

Machine Item Number

PS2 800 0620436

0620442

PSA2 800 0620443

PSW3 1500 0620339

0620444

Foreword

wc_tx001080gb.fm 4

PS / PSA / PSW... Table of Contents

wc_bo0176745en_001TOC.fm 5

1. Foreword 3

2. Safety Information 6

2.1 Operating and Electrical Safety ............................................................ 7

2.2 Informational Labels ............................................................................. 7

3. Operation 8

3.1 Names of Parts ..................................................................................... 8

3.2 Prior to Operation ................................................................................. 9

3.3 Installation ............................................................................................ 9

3.4 Electrical Wiring .................................................................................. 14

3.5 Electrical Circuit Diagrams ................................................................. 16

3.6 Operation ............................................................................................ 18

4. Maintenance 23

4.1 Periodic Maintenance Table ............................................................... 23

4.2 Maintenance and Inspection .............................................................. 24

4.3 Disassembly/Reassembly .................................................................. 27

4.4 Disassembly (PS / PSA) ..................................................................... 28

4.5 Reassembly (PS / PSA) ..................................................................... 29

4.6 Disassembly (PSW) ........................................................................... 30

4.7 Reassembly (PSW) ............................................................................ 31

4.8 Troubleshooting .................................................................................. 32

5. Technical Data 34

5.1 Standard Specifications ...................................................................... 34

5.2 Operating Specifications .................................................................... 35

5.3 Dimensions ........................................................................................ 36

Safety Information PS / PSA / PSW...

wc_si000289gb.fm 6

1. Safety Information

This manual contains DANGER, WARNING, CAUTION, NOTICE and

NOTE callouts which must be followed to reduce the possibility of

personal injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: Contains additional information important to a procedure.

DANGER

WARNING

CAUTION

PS / PSA / PSW... Safety Information

wc_si000289gb.fm 7

1.1 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded,

grounding-type receptacle.

Risk of electric shock—this pump has not been investigated for use in

swimming pool areas.

An acceptable motor-control switch shall be provided at the time of

installation according to local codes and regulations.

To reduce risk of electric shock, follow instructions in this manual for

proper installation.

CAUTION: This pump may automatically restart. Prior to working on

the pump or control panel, all supply circuits must be disconnected.

CAUTION: Risk of shock—do not remove cord and strain relief.

1.2 Informational Labels

Label Meaning

A nameplate listing the model number, item num-

ber, revision number, and serial number is

attached to each unit. Please record the informa-

tion found on this plate so it will be available

should the nameplate become lost or damaged.

When ordering parts or requesting service infor-

mation, you will always be asked to specify the

model number, item number, revision number,

and serial number of the unit.

WARNING

Wacker Neuson Corporation

Menomonee Falls, WI 53051 USA

Model Item No. Rev.

Serial No.

VHz

kWkgMax. L/minMax. m

MADE IN

TAIWAN

HPlbsMax. GPMMax. ft

CUS

L

I

S

T

E

D

R

Phase

C22.2 No. 108-M89

2001993

Conforms to UL Std. 778

Cert. to CAN/CSA St d.

Amp.

Man. Y/M

THERMALLY PROTECTED

INDOORS OR OUTDOORS

CSA ENCLOSURE 3

Operation PS / PSA / PSW...

wc_tx000989gb.fm 8

2. Operation

2.1 Names of Parts

See Graphic: wc_gr005716

Ref Description Ref Description

1 Lifting handle 8 Seal-mechanical

2 Coupling 9 Lubricant

3 Oil lifter 10 Seal-dust

4 Oil plug 11 Sleeve

5 Cover-suction 12 Housing-oil

6 Strainer 13 Wear ring

7 Cable assembly 14 Impeller

1

2

7

8

9

10

11

12

13

14

3

4

5

6

wc_gr005716

2

PS / PSA / PSW... Operation

wc_tx000989gb.fm 9

2.2 Prior to Operation

When the pump is delivered, first perform the following checks:

• Inspection

While unpacking, inspect the product for damage during shipment, and

make sure all bolts and nuts are tightened properly.

• Specification check

Check the model number to make sure it is the product that was

ordered. Be certain it is the correct voltage and frequency.

Note: If there is any problem with the product as shipped, contact your

nearest dealer or Wacker Neuson representative at once.

• Product specifications

Do not operate this product under any conditions other than those for

which it is specified. Failure to observe this precaution can lead to

electrical shock, current leakage, fire, water leakage or other

problems.

2.3 Installation

If the pump is used for outdoor fountains, garden ponds and similar

places, or to drain a swimming pool, the pump must be supplied by an

isolating transformer or connected to a Residual Current Device (RCD)

with a residual operating current not exceeding 30 mA.

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards.

Refer to wiring diagram.

Do not use this pump in liquids other than water, such as oil, salt water,

or organic solvents.

Use with a power supply voltage within ±5% of the rated voltage.

Do not use in water temperatures outside the range of 0–40°C

(32–104°F) which can lead to failure, electrical leakage or shock.

Do not use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note: Consult your local dealer or Wacker Neuson representative

before using with any liquids other than those indicated in this manual.

CAUTION

WARNING

Operation PS / PSA / PSW...

wc_tx000989gb.fm 10

Preparing for installation

Before installing the pump at a work site, you will need to have the

following tools and instruments ready:

• Insulation resistance tester (megohmmeter)

• AC voltmeter

• AC ammeter (clamp-on type)

• Bolt and nut tighteners

• Power supply connection tools (screwdriver or box wrench)

Note: Please also read the instructions that come with each of the test

instruments.

Checks to make before installation

• When a grounded plug is used:

Use the megohmmeter to measure the insulation resistance between

the cable assembly prongs and ground.

• When connection leads are used:

With the megohmmeter, measure the insulation resistance between

each core lead and the ground lead.

Reference insulation resistance: 20MW or greater

Note: The reference insulation resistance (20MW or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation, see “Periodic Maintenance Table.”

Improper ways to measure insulation resistance

See Graphic: wc_gr000258

1. Between the plug prongs.

2. Between the electrodes on the level relay unit.

3. Between the electrodes on the level relay unit and the plug prongs.

1

2

wc

_

gr000258

3

PS / PSA / PSW... Operation

wc_tx000989gb.fm 11

Precautions during installation

Do not under any circumstances install or move the pump by

suspending it from the cable assembly. The cable may be damaged,

causing electrical leakage, shock, or fire.

When installing the pump, pay close attention to its center of gravity

and weight. If it is not lowered into place correctly, it may fall and be

damaged or cause injury.

When transporting the pump by hand, be sure to employ manpower

commensurate with the weight of the pump. To avoid back injury when

lifting the pump, bend the knees to pick it up rather than bending your

back only.

2.3.1 This pump series is offered with a variety of discharge fittings. Follow

procedures noted below to assure a proper discharge connection.

Threaded Discharge Fitting (BSP) –

Tighten hose coupling or discharge pipe securely and with proper

gaskets.

Quick Disconnect Coupling (QD) –

Assure coupling is tightened securely to pump discharge fitting and

companion coupling is securely fastened with proper gaskets.

Barbed Discharge Fitting (Barb) –

Place hose clamp over hose and push hose to the base of the

discharge fitting. Tighten the hose clamp to secure the hose in place.

2.3.2 Avoid dropping the pump or other strong impact. Lift the pump by

holding it firmly with the hands or by attaching a rope or chain to the

handle.

Note: On cable assembly handling, see “Electrical Wiring.”

2.3.3 Install the pump in a location with sufficient water level, where water

collects readily.

Note: See “Operating Water Level” for the water level necessary for

operation. The discharge end of the hose should be located higher

than the water surface. If the end of the hose is submerged, water may

flow back to the pump when the pump is stopped; and if the hose end

is lower than the water surface, water may overflow when the pump is

turned off.

2.3.4 The hose should be run as straight as possible, since excessive

bending will hinder the water flow, preventing sufficient lift, and can

even cause the hose to become clogged with earth. If the hose is

crimped near the pump, air can become trapped in the pump and

cause idle running.

WARNING

CAUTION

Operation PS / PSA / PSW...

wc_tx000989gb.fm 12

If large quantities of earth are sucked up, damage resulting from

friction in the pump can lead to electrical leakage and shock.

2.3.5 Use the pump in the upright position. To prevent the pump from

becoming submerged in mud, mount it on a block or other firm base if

necessary.

2.3.6 If used in a permanent installation, where the pump is not readily

accessible after installation, please contact Wacker Neuson for a

duplicate nameplate to be installed at the wellhead or on the control

box so that it will be readily visible.

CAUTION

PS / PSA / PSW... Operation

wc_tx000989gb.fm 13

Notes:

Operation PS / PSA / PSW...

wc_tx000989gb.fm 14

2.4 Electrical Wiring

Performing electrical wiring

Electrical wiring should be performed by a qualified person in accord

with all applicable regulations. Failure to observe this precaution not

only risks breaking the law but is extremely dangerous.

Incorrect wiring can lead to current leakage, electrical shock or fire.

Always make sure the pump is equipped with the specified overload

protectors and fuses or breakers, so as to prevent electrical shock from

a current leak or pump malfunction.

Operate within the capacity of the power supply and wiring.

Grounding

Do not use the pump without first grounding it properly. Failure to

ground it can lead to electrical shock from a current leak or pump

malfunction.

Do not attach the grounding wire to a gas pipe, water pipe, lightning

arrester or telephone grounding wire. Improper grounding can result in

electrical shock.

Connecting the power supply

Before connecting leads to the terminal strip, make certain the power

supply is turned off (circuit breaker, etc.), to avoid electrical shock,

shorting, or unexpected starting of the pump, leading to injury.

Before inserting the power supply plug, make certain the power supply

is turned off (circuit breaker, etc.), to avoid electrical shock, shorting,

or unexpected starting of the pump, leading to injury.

Do not use the pump with the cable assembly or plug connected

loosely, which can result in electric shock, shorting, or fire.

Draw power from a dedicated power outlet rated at 15 A or above.

Sharing the outlet with other equipment may cause overheating at the

branch outlet and could result in fire.

NOTICE: Be sure to use a dedicated power supply with a ground

leakage circuit breaker.

Grounded plug

Connect only to receptacle of proper voltage and current rating

matching that of the plug provided with the cable assembly.

WARNING

CAUTION

WARNING

CAUTION

PS / PSA / PSW... Operation

wc_tx000989gb.fm 15

Without Plug

Tighten the ends of the cable assembly securely against the terminal

board. If installation of a grounded plug is required, use only a properly

rated and approved CEE plug and secure the ends of the cable

assembly securely to power and ground terminals in accordance with

the plug manufacturer’s instructions.

See Graphic: wc_gr000309

Cable Assembly

If it is necessary to extend the cable assembly, use a core size equal

to or larger than the original. This is necessary not only to avoid a

performance drop, but to prevent cable overheating which can result in

fire, electrical leakage or electrical shock.

If a cable with cut insulation or other damage is submerged in the

water, there is a danger of damage to the pump, electrical leakage,

electrical shock, or fire.

Be careful not to let the cable assembly be cut or become twisted. This

may result in damage to the pump, electrical leakage, electrical shock,

or fire.

If it is necessary to submerge the connection wires of the cable

assembly in water, first seal the wires completely in a molded

protective sleeve, to prevent electrical leakage, electrical shock, or fire.

Do not allow the cable assembly wires or power supply plug to become

wet.

Make sure the cable does not become excessively bent or twisted, and

does not rub against a structure in a way that might damage it.

If used in a deep-well installation, the cable assembly should be

secured every twenty feet.

Br

L

L1

L2

G/Y

wc

_

gr000309

G

CAUTION

Operation PS / PSA / PSW...

wc_tx000989gb.fm 16

2.5 Electrical Circuit Diagrams

See Graphic: wc_gr005717

Ref. Description Ref. Description

1 Capacitor 7 Heater

2 Main coil 8 Level relay unit

3 Auxiliary coil 9 Transformer

4 Protector 10 Electrode

5 Frame grounding 11 Switch

6 Ground — —

R (Br)

W (L)

G (G/Y)

R (Br)

W (L)

G (G/Y)

R (Br)

W (L)

G (G/Y)

R

W

R

W

G

6

5

B

W

G

5

7

11

7

4

9

8

10

1

2

3

R (Br)

W (L)

G (G/Y)

G/Y

B

5

11

4

1

2

3

1

2

3

PS2 800 PSW3 1500

PSA2 800

wc_gr005717

PS / PSA / PSW... Operation

wc_tx000989gb.fm 17

If connected to a circuit protected by a fuse, use a time-delay fuse with

this pump.

Wire Colors

B Black V Violet Or Orange

G Green W White Pr Purple

L Blue Y Yellow Sh Shield

P Pink Br Brown LL Light Blue

R Red Cl Clear G/Y Green/Yellow

T Tan Gr Gray

CAUTION

Operation PS / PSA / PSW...

wc_tx000989gb.fm 18

2.6 Operation

Before starting

2.6.1 Make sure once again that the product is of the correct voltage and

frequency rating.

NOTICE: Using the product at other than rated voltage and frequency

will not only lower its performance but may damage the product.

Note: Confirm the rated voltage and frequency on the model

nameplate.

2.6.2 Confirm the wiring, supply voltage, circuit breaker capacity, and motor

insulation resistance.

Reference insulation resistance = 20 MW or greater.

Note: The reference insulation resistance (20 MW or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation see “Periodic Maintenance Table.”

2.6.3 The setting on the circuit breaker or other overload protector should be

made in accord with the rated current of the pump.

Note: See “Operating Specifications” for the rated current of the pump.

2.6.4 When powering the pump with a generator, be certain the generator is

sized to supply the required power for the pump and any other

equipment powered by the generator.

Non-Automatic Models (PS2 800, PSW3 1500 )

Test Operation

Do not operate the pump while it is suspended in the air. The recoil

may result in injury or other major accident.

Do not start the pump when people are standing next to it. A current

leak can result in electrical shock.

Run the pump for a short time (3–10 minutes) and confirm the

following:

• Using an ammeter (clamp-on type), measure the operating

current at the L1 and L2 phase wires on the terminal.

COUNTERMEASURE: If the operating current exceeds the rated

value, pump motor overload may be a cause. Make sure the pump has

been installed under proper conditions as described in Installation.

• Using an AC voltmeter (tester), measure voltage at the terminals.

Supply voltage tolerance: within ±5% of rated voltage.

WARNING

PS / PSA / PSW... Operation

wc_tx000989gb.fm 19

COUNTERMEASURE: If the supply voltage is outside the tolerance,

possible causes are the power supply capacity or an inadequate

extension cable. Look again at the wiring diagram and make sure the

conditions are proper.

In case of very excessive vibration, unusual noise or odor, turn off the

power immediately and consult your nearest dealer or Wacker

representative. Continuing to operate the pump under abnormal

conditions may result in electrical shock, fire, or current leakage.

Operation

Make sure no extraneous objects such as pins, nails or other metal

objects are sucked into the pump. These can damage the pump or

cause it to malfunction, and can result in electrical shock or electrical

leakage.

When the pump is not used for an extended period, be sure to turn off

the power (circuit breaker, etc.). Deterioration of the insulation may

lead to electrical leakage, electrical shock, or fire.

In case of a power outage, turn off the power to the pump to avoid

having it start unexpectedly when the power is restored, presenting

serious danger to people in the vicinity.

The pump may become hot during operation. Do not touch an

operating pump. Allow the pump to cool before handling.

Pay careful attention to the water level while the pump is operating. Dry

operation may cause the pump to malfunction.

Note: See section “Operating Water Level” for the water level

necessary for operation.

If the protection system operates due to an overload or malfunction,

causing the pump to stop, first investigate and remove the cause

before restarting.

CAUTION

WARNING

CAUTION

Operation PS / PSA / PSW...

wc_tx000989gb.fm 20

Operating water level

Do not operate the pump below the C.W.L. (Continuous running Water

Level) indicated below. Failure to observe this condition may result in

damage to the pump, current leakage or electrical shock.

See Graphic: wc_gr005720

Operating Water Level.

Pump Model C.W.L.

PS2 800 50 mm (2 in.)

PSA2 800 80 mm (3.15 in.)

PSW3 1500

CAUTION

PS2 800, PSA2 800

PSW3 1500

wc_gr005720

La page charge ...

Wacker Neuson PSW31500 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PSW31500 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents