Bounty Hunter Titan 3000XD Le manuel du propriétaire

Marque: Bounty Hunter

Modèle: Titan 3000XD

Catégorie: Mesure, test

Taper: Le manuel du propriétaire

Owner’s

Manual

Published by First Texas Products, L.P.

Titan is made exclusively for Kellyco Metal Detector by First Texas Products, L.P.

www.kellycodetectors.com

1085 Belle Avenue, Winter Springs, FL 32708

(407) 699-8700 MTITAN3-03/08

METAL DETECTOR SUPERSTORE

TREASURE HUNTER’S CODE OF ETHICS:

1. Respect the rights and property of others.

2. Observe all laws, whether national, state or local.

3. Never destroy historical or archaeological treasures.

4. Leave the land and vegetation as it was. Fill in the holes.

5. All treasure hunters may be judged by the example you set. Always

obtain permission before searching any site. Be extremely careful

while probing, picking up, or discarding trash items.

…And ALWAYS COVER YOUR HOLES!

First Texas Products, L.P.

Five Year Limited Warranty

Titan Metal Detectors are warranted against defects in workman-

ship or materials under normal use for five years from date of

purchase to the original user. Liability in all events is limited to

the purchase price paid.

Liability under this WARRANTY is

LIMITED to replacing or repairing, at our option, any Titan Detec-

tor returned, shipping cost prepaid, to

First Texas Products, L.P.

1465-H Henry Brennan

El Paso, Texas 79936

Damage due to neglect, accidental damage or misuse of this

product is not covered by this warranty.

2 23

The following terms are used throughout the manual, and are standard terminology

among detectorists.

Reference to a metal being "eliminated" means that the detector will not emit

a tone, nor light up an indicator, when a specified object passes through the

coil’s detection field.

When the detector emits different tones for different types of metals, and

when the detector "eliminates" certain metals, we refer to this as the detector

"discriminating" among different types of metals.

Discrimination is an important feature of professional metal detectors.

Discrimination allows the user to ignore trash and otherwise undesirable

objects.

A relic is an object of interest by reason of its age or its association with

the past. Many relics are made of iron, but can also be made of bronze or

precious metals.

Iron is a common, low-grade metal that is an undesirable target in certain

metal detecting applications. Examples of undesirable iron objects are

old cans, pipes, bolts, and nails. Sometimes, the desired target is made

of iron. Property markers, for instance, contain iron. Valuable relics can

also be composed of iron; cannon balls, old armaments, and parts of old

structures and vehicles can also be composed of iron.

Metals which are made of, or contain, iron.

Pinpointing is the process of finding the exact location of a buried object.

Long-buried metals can appear exactly like the surrounding soil, and can

therefore be very hard to isolate from the soil.

Discarded pull-tabs from beverage containers are the most bothersome

trash items for treasure hunters. They come in many different shapes and

sizes. Most pull-tabs can be eliminated with the Mode Control, but some

other valuable objects can have a magnetic signature similar to pull-tabs,

and will also be eliminated when discriminating out pull-tabs.

Ground Balancing is the ability of the detector to ignore, or "see through," the

earth’s naturally occurring minerals, and only sound a tone when a metal

object is detected.

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Quick-Start Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7

Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 11

All Metal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Discrimination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Notch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ITD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11

Pinpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Audio Target Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Target and Depth Display . . . . . . . . . . . . . . . . . . . . . . . . . .13-14

Sensitivity Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

In The Field Techniques . . . . . . . . . . . . . . . . . . . . . . . . . 16 - 21

Ground Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Treasure Hunter’s Code of Ethics . . . . . . . . . . . . . . . Back Cover

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

22 3

Assembly is easy and requires no tools.

Position the lower stem (the straight tube)

with the silver button toward the back.

Using the bolt and knurled knob,

attach the search coil to the plastic

extension protruding from the

lower stem.

Press the button

on the upper end

of the lower stem,

and slide the lower

stem into the upper

stem.

Adjust the stem to a length

that lets you maintain a

comfortable upright posture,

with your arm relaxed at

your side. Tighten the stem

locking nut.

Wind the cable securely around the stem.

Insert the plug into the matching connector on the right underside of the

detector body. Be sure

that the key-way and pins

line up correctly.

Do not force the plug

in. Excess force will cause

damage.

To disconnect the cable,

pull on the plug. Do not

pull on the cable.

SYMPTOM CAUSE SOLUTION

Detector chatters • Using detector • Use detector

or beeps erratically indoors outdoors only

• Using detector near • Move away

power lines

from power lines

• Using 2 detectors in • Keep 2 detectors

close proximity at least 20’ apart

• Highly oxidized • Only dig up

buried object repeatable

signals

• Environmental •

Reduce sensitivity

electromagnetic until erratic

interference signals cease

False high-tone •

Over-adjusted

• Move GB knob

signals ground balance

counter clockwise

knob

LCD does not lock • Multiple targets •

Move coil slowly

on to one target ID present at different angles

or detector emits • Highly oxidized

multiple tones target

• Sensitivity set • Reduce sensitivity

too high

No power, no • Dead batteries • Replace batteries

sounds • Poor

battery • Push batteries in

contact

tighter

• Cord not connected •

Insert paper spacers

securely (see page 5)

•

Check connections

How To Pinpoint Targets Using The

PINPOINT Mode

When you’ve discovered a target you wish to dig,

do the following:

1. Hold the searchcoil about half an inch above the ground,

off to the side of where you think the target probably is.

2. Tap the PINPOINT touchpad button. This will put you into the All Metal Pinpoint

mode. NOTE: unlike the other modes, this mode does not require the searchcoil to

be in motion to detect a target.

3. Lift the searchcoil slightly, and pass it over the target. The sound will be loudest over

the center of the target.

To Narrow It Down Further:

4.Now that you know about where the target is, again lower the searchcoil to about half

an inch above the ground, near the center of the target but not right over the top. Tap

the button again. The sound will instantly go away.

5.Lift the searchcoil slightly and move it horizontally

over the target. The audible response zone will be

much narrower. If you move the searchcoil around

right and left and also forward and back, making an

“X” pattern over the target, you can determine the

location of the target usually within an inch or two.

NOTE: if at any time it seems like the signal may be

drifting, just tap the Pinpoint button. This restores

the signal to its zero level.

Ê vÊ ÌiÊ `iÌiVÌÀÊ

Ài>ÃÊ

ÃiÌÊ ÜÌÊ ÌiÊ

Ãi>ÀVVÊ £ÉÓÊ

VÊ ÛiÀÊ ÌiÊ

}ÀÕ`]ÊÊvÕÀÌiÀÊ

clockwiseÊ

adjustmentÊ

is necessary.

È°Ê vÊÌiÊ `iÌiVÌÀÊ iÌÃÊ ÃÕ`Ê ÜÌÊ ÌiÊ VÊ ÛiÀÊ ÌiÊ }ÀÕ`Ê Ê -/*Ê x]Ê

vÕÀÌiÀÊ>`ÕÃÌiÌÊvÊÌiÊ}ÀÕ`ÊL>>ViÊ "ÊÃÊÀiµÕÀi`Ê>ÃÊvÜÃ\

ÊU Ê Ê vÌÊÌiÊÃi>ÀVÊVÊÜ>ÃÌÊ}

ÊU Ê Ê ,Ì>ÌiÊÌiÊ}ÀÕ`ÊL>>ViÊ "ÊVVÜÃiÊ£É£ÈÊinch

ÊUÊÊ*ÀiÃÃÊ* *" /

ÊU Ê ÊÜiÀÊÌiÊÃi>ÀVÊVÊÌÊÌiÊ}ÀÕ`Ê>}>

Ê vÊÌiÊ`iÌiVÌÀÊÃÌÊiÌÃÊ>ÊÌi]ÊÀi«i>ÌÊÌÃÊ«ÀVi`ÕÀi°Ê9ÕÊ>ÀiÊÃi>ÀV}Ê

vÀÊÌiÊ}ÀÕ`ÊL>>ViÊLÊ«ÃÌÊÜiÀiÊÌiÊ`iÌiVÌÀÊÃÊÕÃÌÊÃiÌ°Ê

ÌÊ ÃÊ «ÀÌ>ÌÊ ÌÊ ÛiÊ ÌiÊ LÊ Ê Ã>Ê VÀiiÌÃÊ Ê À`iÀÊ ÌÊ v`Ê

ÌiÊvÀÃÌÊÃiÌÌ}ÊÛ}ÊVVÜÃi®Ê>ÌÊÜVÊÌiÊ`iÌiVÌÀÊÀi>ÃÊÃiÌ°Ê

/Ê ÃÕÀiÊ ÞÕÀÃivÊ vÊ ÌiÊ «Ì>Ê >`ÕÃÌiÌ]Ê ÛiÊ ÌiÊ  "Ê Ã}ÌÞÊ

VÕÌiÀVVÜÃiÊvÀÊ >ÊÃiÌ>`ÕÃÌi`Ê «ÃÌÊ ÌÊViVÊ vÀÊ ÌiÊ ÃÌÊ

VÕÌiÀVVÜÃiÊÃiÌÊ«ÃÌÊ«ÃÃLi°

vÊÌiÊ "ÊÃÊÛiÀ>`ÕÃÌi`ÊinÊÌiÊVVÜÃiÊ`ÀiVÌ]ÊÌiÊ`iÌiVÌÀÊV> loseÊ

ÃiÃÌÛÌÞ or produce false high-tone signals°ÊÊÛiÀ>`ÕÃÌi`ÊV`ÌÊV>Ê>ÃÊ

cause the detector to ÃÕ`ÊvvÊÜiÊÌiÊVÊÃÊvÌi`Ê>Ü>ÞÊvÀÊÌiÊ}ÀÕ`°

ÃÊ ÞÕÀÊ Ãi>ÀVÊ Ì>iÃÊ ÞÕÊ ÌÊ `vviÀiÌÊ >Ài>Ã]Ê ÛiÀvÞÊ ÌiÊ }ÀÕ`Ê L>>ViÊ

ÃiÌÌ}Ê«iÀ`V>ÞÊÕÃ}ÊÌiÊ>LÛiÊ«ÀVi`ÕÀi°ÊÊ7ÌÊ>Ê}i}À>«V>Ê>Ài>]Ê

}ÀÕ`ÊV`ÌÃÊV>ÊV>}i°Ê6>ÀÞ}ÊiiÛ>ÌÃ]Ê«ÀÝÌÞÊÌÊÜ>ÌiÀ]Ê>`Ê

VViÌÀ>ÌÃÊvÊÀV]Ê Ã>`ÊÀÊV>ÞÊV>Ê >Ê>vviVÌÊ}ÀÕ`ÊV`ÌÊ >`Ê

ÃiÌiÃÊÀiµÕÀiÊÀiV>LÀ>ÌÊÜÌÊÌiÊ}ÀÕ`ÊL>>ViÊL°

 

1ÃiÊ Ê

L>ÌÌiÀiÃÊÞ°

/ÊÃÌ>ÊÌiÊ

L>ÌÌiÀiÃ\

Ê ,iÛiÊ ÌiÊ

L>ÌÌiÀÞÊ VÛiÀÊ LÞÊ

`Ãi}>}}Ê ÌiÊ

V«Ê>ÌÊÌiÊL>V°

Ê }ÊÌiÊ«>ÀÌÞÊ

vÊ ÌiÊ L>ÌÌiÀiÃÊ

VÀÀiVÌÞ]Ê ÜÌÊ

ÌiÊ «ÃÌÛiÊ ¸³¸Ê

ÌÜ>À`Ê ÌiÊ VÊ

«Õ}Ê ViVÌ]Ê

>ÃÊ `V>Ìi`Ê LÞÊ

ÌiÊÊ³ÊÊ>`ÊÊqÊÊ

`V>ÌÀÃÊ Ê ÌiÊ

ÕÃ}°

Ê ÃiÀÌÊ Ó®Ê 6ÌÊ Ê L>ÌÌiÀiÃ]Ê ÜÌÊ ÌiÊ VÌ>VÌÃÊ «Ìi`Ê Ü>À`]Ê

>`Ê«ÀiÃÃÊ`ÜÊÊÌiÊL>VÊvÊÌiÊL>ÌÌiÀiÃÊÌÊÃ>«ÊÌiÊÌÊ«>Vi°

-iÊ LÀ>`ÃÊ vÊ L>ÌÌiÀiÃ]Ê `ÕiÊ ÌÊ `vviÀiÌÊ ÕÌÃ`iÊ `iÃÃ]Ê ÜÊ

ÀiµÕÀiÊ`iÀ>ÌiÊvÀViÊÌÊVi>ÀÊÌiÊÀiÌ>}ÊÌ>LÃ°

vÊÌiÊL>ÌÌiÀiÃÊvÌÊÃiÞ]Ê>`ÊÞÕÊÜ>ÌÊÌÊ

}Õ>À>ÌiiÊ>Ê ÛiÀÞÊ ÃiVÕÀiÊ iiVÌÀV>Ê VÌ>VÌ]Ê

ÃiÀÌÊ >Ê «iViÊ vÊ «>«iÀÊ ÀÊ ÌÊ V>À`L>À`Ê

LiÌÜiiÊ ÌiÊ L>VÊ vÊ ÌiÊ L>ÌÌiÀÞÊ >`Ê ÌiÊ

ÃÕ««ÀÌ}Ê«ÃÌ°

Ê ,i«>ViÊÌiÊL>ÌÌiÀÞÊ`À°

/iÊÜÊ>ÌÌiÀÞÊ`V>ÌÀÊÜÊViÊÊ>`ÊÃÌ>ÞÊ

ÊvÊÌiÊL>ÌÌiÀiÃÊii`ÊÌÊLiÊÀi«>Vi`°

ÃÌÊiÌ>Ê`iÌiVÌÀÊ«ÀLiÃÊ>ÀiÊ`ÕiÊÌÊ«À«iÀÞÊÃÌ>i`ÊL>ÌÌiÀiÃ]ÊÀÊ

ÌiÊ ÕÃiÊ vÊ >>iÊ ÀÊ `ÃV>À}i`Ê L>ÌÌiÀiÃ°Ê Ê vÊ ÌiÊ `iÌiVÌÀÊ `iÃÊ ÌÊ

ÌÕÀÊ]Ê«i>ÃiÊViVÊÌiÊL>ÌÌiÀiÃ°ÊvÊÌiÊL>ÌÌiÀiÃÊ>ÀiÊÃi]Ê«ÀiÃÃÊÌiÊ

vÀÜ>À`ÊÜiÊ«ÀiÃÃ}ÊÌiÊ" ÊÌÕVÊ«>`°

 Ê-Ê"Ê""-Ê//,-

6 19

I. Supplies Needed

• A Nail • A Quarter

• A Pull-Tab from a beverage can • A Zinc Penny (dated after 1982)

II. Position the Detector

a. Place the detector on a

table, with the search coil

hanging over the edge.

(or better, have a friend

hold the detector, with

the coil off the ground)

b. Keep the search coil away

from walls, floors, and

metal objects.

c. Remove watches, rings and other jewelry or metal objects

from hands and wrists.

d. Turn off appliances or lights that cause electromagnetic interference.

e. Pivot search coil back toward the detector body.

III. Power Up

Press the ON touch pad.

IV. Wave each Object over the Search Coil

a. Notice a different tone for each object.

Base Tone: Nail

Low Tone: Pull-Tab

Medium Tone: Zinc Penny

High Tone: Quarter

b. Motion is required. Objects must be

in motion over the search coil to be

detected.

V. Press the MODE touch pad

The detector will beep twice and an “R”

will appear under the iron indicator.

Quick-Start Demo continued on next page

Before using the PINPOINT mode, it is necessary to “Ground Balance” your

detector, this ground balancing adjustment offsets the effects of minerals

and salts in the ground.

To GROUND BALANCE your detector:

1. Using the ALL-METAL mode, find a patch of ground which is free of

metal objects. You will use this section of ground to test the detector.

The presence of any metal objects in this area will interfere with this

procedure.

2. Begin with the ground balance

KNOB in the PRESET position.

3. Lift the search coil waist high in the air.

4. Press the PINPOINT touch pad.

5. Lower the search coil to the ground,

maintaining it elevated about 1/2 inch above

the surface (be sure that this ground does

not contain metal).

• If the detector emits sound with the search coil 1/2 inch over the

ground, further ADJUSTMENT IS NECESSARY.

18 7

VI. Wave the Nail over the Search Coil

a. The Nail will not be detected. b. The Nail has been "Discriminated Out."

VII. Press the “DISCRIMINATION-▲”

touchpad twice.

Three

“R”s are now displayed.

VIII. Wave all objects over the

Search Coil

The Nail and Pull-Tab will not be detected. The other objects will be

detected with their own distinctive tones.

IX. Press the NOTCH touchpad.

A flashing

“R” will appear

under the 5¢/PT segment.

X. Press the DISCRIMINATION ▲

touchpad three times.

The flashing “R” will move to the

ZINC segment.

XI. Press the NOTCH touchpad again.

The “R” will appear under zinc.

XII. Wave the zinc penny over the search coil.

The penny is discriminated out.

XIII. Press the DISC A-M touchpad

The detector returns to ALL-METAL mode. No “R”s are displayed.

All types of metals will be detected.

XIV. Wave the pull-tab over the coil.

XV. Press the ITD touchpad.

An “R” will appear.

XVI. Wave the pull-tab over the search coil

again.

The pull-tab (most recently detected item)

is eliminated from detector.

XVII. Press the PINPOINT touch pad.

Hold one of the metal objects motionless over the search coil.

• All Metal objects are now detected.

• Depth and Target indicator do not lluminate in this mode.

•

One monotone sound indicates the presencce of any type of metal.

objects. If you are new to the hobby,

you may want to dig all targets at

first. With practice in the field, you

will learn to better discern the nature

of buried objects by the nature of the

detector’s response.

You may encounter some false

signals as you proceed. False

signals occur when the detector

beeps, but no metal target is present.

False signals can be induced by

electromagnetic interference,

oxidation, or highly mineralized

ground soils. If the detector beeps

once, but does not repeat the signal

with several additional sweeps over

the same spot, there is probably no

target present.

When searching very trashy ground,

it is best to scan small areas with

slow, short sweeps. You will be

surprised just how much trash

metal and foil you will find in some

areas. The trashiest areas have been

frequented by the most people, and

frequently hold the most promise for

finding the most lost valuables.

Also maintain the search coil

positioned just above the surface of

the ground, without making contact

with the ground. Making contact

with the ground can cause false

signals.

8 17

Press the POWER touch pad.

• The detector will beep

4 times.

• All display segments will

illuminate momentarily.

• The SENSITIVITY and

BATTERY indicators will

stay illuminated.

Depending on the operation mode selected, the Titan 3000 XD detects metal

both with the coil in motion, or with the coil motionless. In the PINPOINT

mode of operation, metal is detected with the coil motionless over the

ground. This no-motion operation helps to locate the exact location of buried

objects, and is very useful in understanding the size and shape of buried

metal objects. The PINPOINT mode offers deeper ground penetration, but

cannot classify targets, nor indicate their depth.

The other operating modes require the coil to be in motion to detect a target.

When in the DISCRIMINATION, ALL-METAL or NOTCH modes, the coil

must be in continuous motion. It is often useful to search for targets in a

motion mode, and when identified, pinpoint their location with the PINPOINT

control.

At its default sensitivity setting, the detector will detect a coin-sized object,

such as a quarter, buried approximately seven inches deep. To change the

sensitivity level, and thus the detection depth, press the SENSITIVITY ▲ or

▼ keys. The 6-segment scale at the left of the display, above “coin depth”,

indicates the sensitivity level when these touch pads are depressed.

At higher sensitivity levels, the detector is susceptible to electromagnetic

interference from electronic devices. Reduce sensitivity if demonstrating

indoors or if using near power lines or electrical equipment. Reduce

sensitivity if detector emits false signals.

WHAT

READS

LIKE THIS

…MAY

ACTUALLY

BE THIS

Swing the search coil slowly,

overlapping each sweep as you move

forward. It is important to sweep the

coil at a consistent speed over the

ground as you search. After identifying

a target, your sweep technique can

help in identifying both the location

and the nature of the target. If you

encounter a weak signal, try moving

the coil in short, rapid sweeps over the

target zone; such a short rapid sweep

may provide a more consistent target

identification.

Most worthwhile objects will respond

with a repeatable tone. If the signal

does not repeat after sweeping the

coil directly over the suspected target

a few times, it is more than likely trash

metal.

Crossing the target zone with multiple

intersecting sweeps at multiple

angles is another way to verify the

repeatability of the signal, and the

potential of the buried target. To use

this method, walk around the target

area in a circle, sweeping the coil

across the target repeatedly, every 30

to 40 degrees of the circle, about ten

different angles as you walk completely

around the target. If a high-tone target

completely disappears from detection

at a given angle, chances are that you

are detecting oxidized ferrous metals,

rather than a silver or copper object.

If the tone changes at different angles,

you may have encountered multiple

16 9

The detector defaults to ALL METAL mode after powering on. In this mode,

all types of metals will be detected. An object’s PROBABLE identification is

indicated by the arrows at the top of the display. In addition, the

PROBABLE

depth of coin-sized objects is indicated by the rectangular segment indicators

on the left side of the display. All detected objects will cause the depth indicator

to illuminate. The depth indication is not accurate for larger objects; however,

it will provide accurate relative depth indications. The greater the distance an

object is from the search coil, the greater

its depth value.

Pressing this touch pad will cause

the detector to toggle between two

operating modes, DISCRIMINATION and

ALL-METAL. If the detector is in the

ALL-METAL mode (the default mode),

pressing the touch pad will change the detector into DISCRIMINATION mode.

If the detector is in the DISCRIMINATION mode, pressing the touch pad will

change the detector into ALL-METAL mode

Discrimination is used to eliminate unwanted objects from detection.

To enter this mode, from ALL-METAL mode, press the DISC/A-M touch pad.

After pressing

DISC/A-M, the detector will:

• Beep twice

• Display 3

"R"s under the left-most segments, Iron 1, 2 & 3

Ferrous objects will not be detected in DISCRIMINATION mode.

Heavily oxidized ferrous objects and very large iron objects will sometimes,

however, be detected, usually with a high tone and an indication to the right

of the target indentification scale.

To increase the level of discrimination, press the DISCRIMINATION

touch

pad. Each time the pad is depressed, an additional "R" will appear, thus

eliminating from detection the objects which fall into the corresponding

categories.

To decrease the level of discrimination, press the DISCRIMINATION

▼ touch pad. Each time the ▼ pad is depressed, an illuminated "R"

will disappear, thus returning to detection the objects which fall into the

corresponding categories.

Discrimination Mode is a fixed-start-point elimination system. Objects are

cumulatively eliminated as the level of discrimination increases.

Accurate pinpointing takes practice

and is best accomplished by “X-ing”

the target area.

1. Once a buried target is indicated by

a good tone response, continue

sweeping the coil over the target

in a narrowing side-to-side pat-

tern.

2. Take visual note of the place on the

ground where the “beep” sounds.

3. Stop the coil directly over this spot

on the ground.

4. Now move the coil straight for-

ward and straight back towards

you a couple of times.

5. Again make visual note of the spot

on the ground at which the “beep”

sounds.

6. If needed, “X” the target at

different angles to “zero in” on the

exact spot on the ground at which

the “beep” sounds.

When swinging the coil, be careful

to keep it level with the ground about

one inch from the surface. Never

swing the coil like a pendulum.

WRONG

CORRECT

NOTE: This modern Metal Detector is referred to as a Motion Detector since it can

respond to a target only while the searchcoil is being moved over the Target.

10 15

ELECTROMAGNETIC

INTERFERENCE

The principle use for the Sensitivity

Control is to eliminate Electromagnetic

Interference (EMI).

A hobby metal detector is an extremely

sensitive device; the search coil

creates its own magnetic field and

acts like an antenna. If your detector

beeps erratically when the search coil

is motionless, the unit is probably

detecting another electromagnetic

field.

Common sources of EMI are electric power lines, both suspended and buried,

motors, and household appliances like computers and microwave ovens. Some

indoor electronic devices, such as dimmer switches used on household lighting,

produce severe EMI and can cause the detector to beep erratically. Other metal

detectors also produce their own electromagnetic fields; so if detecting with a

friend, keep two metal detectors at least 20 feet apart.

If the detector beeps erratically, REDUCE THE SENSITIVITY by pressing the

Sensitivity ▼ Pad on the left of the control panel.

SEVERE GROUND CONDITIONS

A secondary use for the Sensitivity Control is to reduce false detection signals

caused by severe ground conditions. While your Titan 3000 XD contains

circuitry to eliminate the signals caused by most naturally occurring ground

minerals, 100% of all ground conditions cannot be anticipated. Highly magnetic

soils found in mountainous and gold-prospecting locations can cause the

detector to emit tones when metal objects are not present. High saline content

soils and sands can sometimes cause the detector to false.

If the detector emits false, non-repeatable, signals, REDUCE THE SENSITIVITY.

MULTIPLE TARGETS

If you suspect the presence of deeper targets beneath a shallower target, reduce

the sensitivity to eliminate the detection of the deeper targets, in order to properly

locate and identify the shallower target.

To selectively eliminate a category from detection within the metallic

spectrum, use the NOTCH Mode

Technical Note:

The NOTCH touch pad causes the status of an "R" segment to

toggle between

ON and OFF.

To use the NOTCH Mode

The NOTCH touch pad can be depressed at any time. But for

first-time use, place the detector in ALL-METAL mode

A first demonstration is best accomplished as follows:

1) Turn the power OFF.

2) Turn the power ON.

3) Press NOTCH.

A flashing

"R" will appear under the IRON-1 segment.

4) Press the DISCRIMINATION touch pad several times.

Notice that the

"R" moves upon each press of the

DISCRIMINATION touch pad.

5) Press NOTCH again.

The flashing "R" will become permanently illuminated.

If an object has been

“notched-out”, you can return it to detection

status. To

“un-notch” a category:

1) Press NOTCH.

2) Move the flashing “R” over the permanently illuminated

“R”, using the DISCRIMINATION or ▼ touch pads.

3) Press NOTCH again.

The ITD (Instant Target Discrimination) control is a convenient way to

eliminate a known undesirable metal object from detection.

To demonstrate the ITD control

1) Set the detector in All-Metal Mode

Note: ITD functions in all motion modes, but is best demonstrated

first from the All-Metal Mode.

2) Pass the search coil over an undesirable object.

3) Notice the Target Indication

Note: You can only ITD objects that register under the

seven left-most segments (from Iron to Zinc).

The table below list some common approximate target value

equivalents. With experience in the filed, you will recognize

many types of metals by their numeric value.

VALUE RANGE POSSIBLE OBJECTS

0-10 Iron

30-39 Nickel - Small/Med. gold rings

43-48 Pull-Tab - Some large gold rings

53-60 Screw Cap

62-74 Zinc, Penny

83-88 Wheat Cent

86-100 Dime

107-127 Quarter

105-120 Liberty Dollar

120-126 Franklin Half Dollar

134-150 Silver Dollar

150-199 Large Metal Object

THREE DIGIT TARGET

INDICATOR

The three digit target indicator, in the middle of the LCD display,

provides a specific target value to help identify buried targets more

accurately. With practice in the field, you will learn to associate target

values with the probable identification of buried objects. The target

value can vary each time the coil passes over the target, depending

upon the angle of the object and the distance from the coil. As a

starting point, refer to the table below.

4) Press ITD. An "R" appears under the segment to be eliminated.

5) Pass the search coil over the same object again.

The undesirable object is eliminated from detection

The ITD control is easy to use in the field. As you are detecting, and encounter

an object which you wish to eliminate from detection, simply press the ITD

touch pad after detecting the object.

The ITD control eliminates the most-recently detected object category from

detection. The category eliminated is indicated with an "R".

Since long-buried objects can appear exactly like the surrounding soil, the

process of finding the exact location of a small object, such as a coin, can be

time-consuming and frustrating. Objects buried many inches deep present

an especially daunting challenge. In addition, during the unearthing process,

care must be taken not to damage valuable relics. The best solution to these

problems is the no-motion PINPOINT mode.

At any time during operation, press the PINPOINT touch pad, and the detector

enters the no-motion mode. In the PINPOINT mode, any object in the coil’s

detection field will induce a monotone hum. The location of a coin-sized object

can be discerned with pinpoint accuracy by narrowing the detection field as

described on page 21.

Be sure that the detector is properly GROUND BALANCED before using the

PINPOINT MODE. See page 19 for manual ground balancing instructions. Also,

consult page 21 for proper no-motion field techniques.

The Target Identification and Target Depth

indicators are disabled in this mode. To

discern the identification and depth of an

object, you must use one of the motion

modes of operation.

Using headphones (not supplied) with your

metal detector makes it easier to identify

subtle changes in the threshold levels for

better detection results, and also reduces

drain on the batteries. The Titan 3000 XD

Metal Detector has a stereo headphone

jack located at the rear of the case.

This device is to be used with interconnecting

cables/headphone cables shorter than three meters.

12 13

While the LCD (Liquid Crystal Display) is very accurate in identifying buried

objects, the user in the field does not always maintain the display screen in his

field of vision. Therefore, we have incorporated an audio feedback mechanism

to alert the user to the nature of buried objects. This audio feedback system first

alerts the user to the presence and classification of objects, whose nature and

location can be confirmed using the LCD display.

The detector can sound four different tones, depending on the object detected.

Audio Target Identification (ATI) classifies metals into four categories.

BASS TONE

Nails, Iron Objects,

& Smallest Gold Objects

LOW TONE

Pull Tabs, Nickels,

& Smaller Gold

MEDIUM TONE

Zinc Pennies (Post 1982),

Larger Gold Objects, Many

screw caps

HIGH TONE

Copper, Silver & Brass

Copper Pennies (Pre 1982)

BASS TONE

Ferrous objects, such as iron and steel, will

induce a bass tone.

The smallest gold objects can also induce a

bass tone.

LOW TONE

Pull-Tabs, nickels & smaller gold

MEDIUM TONE

Newer pennies (post-1982), larger gold

objects, zinc, small brass objects, and most

bottle screw caps will induce medium tones.

Many recent vintage foreign currencies will

induce medium tones.

HIGH TONE

Silver and copper coins, larger brass objects,

older pennies (pre-1982), and highly oxidized

metals will induce high tones. Quarters,

dimes and other precious coins fall into this

category.

The Liquid Crystal Display (LCD) shows the

PROBABLE identification of the targeted

metal, as well as the PROBABLE depth of

the target, in inches.

The detector will register a repeating,

unchanging target identification when

a buried target has been located and

identified. If, upon repeated passes over

the same spot, the target identification

reads inconsistently, the target is probably

a trash item, or oxidized metal. With

practice, you will learn to unearth only the

repeatable signals.

The segment identifications are highly

accurate, when detecting the objects

described on the label. However, if you

buried object, you could be detecting

a metallic object other than the object

described on the label, but with the same

metallic signature. Also, the greater the

distance between the target and the coil, the

less accurate the target identification.

GOLD TARGETS: Gold objects will

Gold will register depending upon its

size. The smaller the gold object, the

further to the left it will register.

Gold flakes will register under Iron-1

Small gold items will register under Iron

or 5¢/PT.

Medium-sized gold items will register

under PT or S-cap.

Large gold items will register under S-

cap or Zinc.

SILVER TARGETS: Silver objects will

25¢, 50¢, or $1, depending on the size

of the object. The larger the object, the

farther to the right it will register.

IRON: Ferrous objects will register on

the far-left side of the target identification

scale. 1, 2, or 3 indicates the relative

size of iron objects. Small nails, for

instance, will usually illuminate the

Iron-1 arrow whereas large structural

ferrous objects will usually illuminate

the Iron-3 arrow.

Objects in this category could be worthless

scrap, or a more valuable iron relic.

5c/PT: Nickels and most newer pull-

tabs(those that stay attached to the

can) will register here.

PT(pull-tabs): Pull-tabs from older

beverage cans will register here. Few

newer pull-tabs will also register here.

Many gold rings will also register here.

S-CAP: Older screw caps from glass

bottles will register here. Large gold rings,

like a class ring, could also register here.

Some non-U.S. coins of recent vintage

will also register here.

ZINC: Newer pennies (post-1982) will

recent vintage will also register here.

Cu10¢: Dimes and pre-1982 pennies will

composed of copper, which has a metallic

signature similar to a dime. Most copper

coins will register here.

Caution: The target indications are

visual references. Many other types of

metal can fall under any one of these

categories. While the Titan 3000 XD will

eliminate or indicate the presence of most

common trash items, it is impossible to

accurately classify ALL buried objects.

The Depth Indicator is accurate for

coin-sized objects. It indicates the

depth of the target, in inches. Large

and irregularly-shaped objects will yield

less reliable depth readings

When passing over an object, the

depth indicator will light up and stay

illuminated until another object is

scanned. Repeated indication at the

same depth level indicates an accurate

target detector. If the depth indication

varies with each sweep, try sweeping

at different angles; there may be more

than one target present. With practice,

you will learn the difference between

accurate readings, multiple targets, and

highly erratic readings which evidence

trash or irregularly shaped objects.

12 13

While the LCD (Liquid Crystal Display) is very accurate in identifying buried

objects, the user in the field does not always maintain the display screen in his

field of vision. Therefore, we have incorporated an audio feedback mechanism

to alert the user to the nature of buried objects. This audio feedback system first

alerts the user to the presence and classification of objects, whose nature and

location can be confirmed using the LCD display.

The detector can sound four different tones, depending on the object detected.

Audio Target Identification (ATI) classifies metals into four categories.

BASS TONE

Nails, Iron Objects,

& Smallest Gold Objects

LOW TONE

Pull Tabs, Nickels,

& Smaller Gold

MEDIUM TONE

Zinc Pennies (Post 1982),

Larger Gold Objects, Many

screw caps

HIGH TONE

Copper, Silver & Brass

Copper Pennies (Pre 1982)

BASS TONE

Ferrous objects, such as iron and steel, will

induce a bass tone.

The smallest gold objects can also induce a

bass tone.

LOW TONE

Pull-Tabs, nickels & smaller gold

MEDIUM TONE

Newer pennies (post-1982), larger gold

objects, zinc, small brass objects, and most

bottle screw caps will induce medium tones.

Many recent vintage foreign currencies will

induce medium tones.

HIGH TONE

Silver and copper coins, larger brass objects,

older pennies (pre-1982), and highly oxidized

metals will induce high tones. Quarters,

dimes and other precious coins fall into this

category.

The Liquid Crystal Display (LCD) shows the

PROBABLE identification of the targeted

metal, as well as the PROBABLE depth of

the target, in inches.

The detector will register a repeating,

unchanging target identification when

a buried target has been located and

identified. If, upon repeated passes over

the same spot, the target identification

reads inconsistently, the target is probably

a trash item, or oxidized metal. With

practice, you will learn to unearth only the

repeatable signals.

The segment identifications are highly

accurate, when detecting the objects

described on the label. However, if you

buried object, you could be detecting

a metallic object other than the object

described on the label, but with the same

metallic signature. Also, the greater the

distance between the target and the coil, the

less accurate the target identification.

GOLD TARGETS: Gold objects will

Gold will register depending upon its

size. The smaller the gold object, the

further to the left it will register.

Gold flakes will register under Iron-1

Small gold items will register under Iron

or 5¢/PT.

Medium-sized gold items will register

under PT or S-cap.

Large gold items will register under S-

cap or Zinc.

SILVER TARGETS: Silver objects will

25¢, 50¢, or $1, depending on the size

of the object. The larger the object, the

farther to the right it will register.

IRON: Ferrous objects will register on

the far-left side of the target identification

scale. 1, 2, or 3 indicates the relative

size of iron objects. Small nails, for

instance, will usually illuminate the

Iron-1 arrow whereas large structural

ferrous objects will usually illuminate

the Iron-3 arrow.

Objects in this category could be worthless

scrap, or a more valuable iron relic.

5c/PT: Nickels and most newer pull-

tabs(those that stay attached to the

can) will register here.

PT(pull-tabs): Pull-tabs from older

beverage cans will register here. Few

newer pull-tabs will also register here.

Many gold rings will also register here.

S-CAP: Older screw caps from glass

bottles will register here. Large gold rings,

like a class ring, could also register here.

Some non-U.S. coins of recent vintage

will also register here.

ZINC: Newer pennies (post-1982) will

recent vintage will also register here.

Cu10¢: Dimes and pre-1982 pennies will

composed of copper, which has a metallic

signature similar to a dime. Most copper

coins will register here.

Caution: The target indications are

visual references. Many other types of

metal can fall under any one of these

categories. While the Titan 3000 XD will

eliminate or indicate the presence of most

common trash items, it is impossible to

accurately classify ALL buried objects.

The Depth Indicator is accurate for

coin-sized objects. It indicates the

depth of the target, in inches. Large

and irregularly-shaped objects will yield

less reliable depth readings

When passing over an object, the

depth indicator will light up and stay

illuminated until another object is

scanned. Repeated indication at the

same depth level indicates an accurate

target detector. If the depth indication

varies with each sweep, try sweeping

at different angles; there may be more

than one target present. With practice,

you will learn the difference between

accurate readings, multiple targets, and

highly erratic readings which evidence

trash or irregularly shaped objects.

14 11

4) Press ITD. An "R" appears under the segment to be eliminated.

5) Pass the search coil over the same object again.

The undesirable object is eliminated from detection

The ITD control is easy to use in the field. As you are detecting, and encounter

an object which you wish to eliminate from detection, simply press the ITD

touch pad after detecting the object.

The ITD control eliminates the most-recently detected object category from

detection. The category eliminated is indicated with an "R".

Since long-buried objects can appear exactly like the surrounding soil, the

process of finding the exact location of a small object, such as a coin, can be

time-consuming and frustrating. Objects buried many inches deep present

an especially daunting challenge. In addition, during the unearthing process,

care must be taken not to damage valuable relics. The best solution to these

problems is the no-motion PINPOINT mode.

At any time during operation, press the PINPOINT touch pad, and the detector

enters the no-motion mode. In the PINPOINT mode, any object in the coil’s

detection field will induce a monotone hum. The location of a coin-sized object

can be discerned with pinpoint accuracy by narrowing the detection field as

described on page 21.

Be sure that the detector is properly GROUND BALANCED before using the

PINPOINT MODE. See page 19 for manual ground balancing instructions. Also,

consult page 21 for proper no-motion field techniques.

The Target Identification and Target Depth

indicators are disabled in this mode. To

discern the identification and depth of an

object, you must use one of the motion

modes of operation.

Using headphones (not supplied) with your

metal detector makes it easier to identify

subtle changes in the threshold levels for

better detection results, and also reduces

drain on the batteries. The Titan 3000 XD

Metal Detector has a stereo headphone

jack located at the rear of the case.

The table below list some common approximate target value

equivalents. With experience in the filed, you will recognize

many types of metals by their numeric value.

VALUE RANGE POSSIBLE OBJECTS

0-10 Iron

30-39 Nickel - Small/Med. gold rings

43-48 Pull-Tab - Some large gold rings

53-60 Screw Cap

62-74 Zinc, Penny

83-88 Wheat Cent

86-100 Dime

107-127 Quarter

105-120 Liberty Dollar

120-126 Franklin Half Dollar

134-150 Silver Dollar

150-199 Large Metal Object

THREE DIGIT TARGET

INDICATOR

The three digit target indicator, in the middle of the LCD display,

provides a specific target value to help identify buried targets more

accurately. With practice in the field, you will learn to associate target

values with the probable identification of buried objects. The target

value can vary each time the coil passes over the target, depending

upon the angle of the object and the distance from the coil. As a

starting point, refer to the table below.

10 15

ELECTROMAGNETIC

INTERFERENCE

The principle use for the Sensitivity

Control is to eliminate Electromagnetic

Interference (EMI).

A hobby metal detector is an extremely

sensitive device; the search coil

creates its own magnetic field and

acts like an antenna. If your detector

beeps erratically when the search coil

is motionless, the unit is probably

detecting another electromagnetic

field.

Common sources of EMI are electric power lines, both suspended and buried,

motors, and household appliances like computers and microwave ovens. Some

indoor electronic devices, such as dimmer switches used on household lighting,

produce severe EMI and can cause the detector to beep erratically. Other metal

detectors also produce their own electromagnetic fields; so if detecting with a

friend, keep two metal detectors at least 20 feet apart.

If the detector beeps erratically, REDUCE THE SENSITIVITY by pressing the

Sensitivity ▼ Pad on the left of the control panel.

SEVERE GROUND CONDITIONS

A secondary use for the Sensitivity Control is to reduce false detection signals

caused by severe ground conditions. While your Titan 3000 XD contains

circuitry to eliminate the signals caused by most naturally occurring ground

minerals, 100% of all ground conditions cannot be anticipated. Highly magnetic

soils found in mountainous and gold-prospecting locations can cause the

detector to emit tones when metal objects are not present. High saline content

soils and sands can sometimes cause the detector to false.

If the detector emits false, non-repeatable, signals, REDUCE THE SENSITIVITY.

MULTIPLE TARGETS

If you suspect the presence of deeper targets beneath a shallower target, reduce

the sensitivity to eliminate the detection of the deeper targets, in order to properly

locate and identify the shallower target.

To selectively eliminate a category from detection within the metallic

spectrum, use the NOTCH Mode

Technical Note:

The NOTCH touch pad causes the status of an "R" segment to

toggle between

ON and OFF.

To use the NOTCH Mode

The NOTCH touch pad can be depressed at any time. But for

first-time use, place the detector in ALL-METAL mode

A first demonstration is best accomplished as follows:

1) Turn the power OFF.

2) Turn the power ON.

3) Press NOTCH.

A flashing

"R" will appear under the IRON-1 segment.

4) Press the DISCRIMINATION touch pad several times.

Notice that the

"R" moves upon each press of the

DISCRIMINATION touch pad.

5) Press NOTCH again.

The flashing "R" will become permanently illuminated.

If an object has been

“notched-out”, you can return it to detection

status. To

“un-notch” a category:

1) Press NOTCH.

2) Move the flashing “R” over the permanently illuminated

“R”, using the DISCRIMINATION or ▼ touch pads.

3) Press NOTCH again.

The ITD (Instant Target Discrimination) control is a convenient way to

eliminate a known undesirable metal object from detection.

To demonstrate the ITD control

1) Set the detector in All-Metal Mode

Note: ITD functions in all motion modes, but is best demonstrated

first from the All-Metal Mode.

2) Pass the search coil over an undesirable object.

3) Notice the Target Indication

Note: You can only ITD objects that register under the

seven left-most segments (from Iron to Zinc).

16 9

The detector defaults to ALL METAL mode after powering on. In this mode,

all types of metals will be detected. An object’s PROBABLE identification is

indicated by the arrows at the top of the display. In addition, the

PROBABLE

depth of coin-sized objects is indicated by the rectangular segment indicators

on the left side of the display. All detected objects will cause the depth indicator

to illuminate. The depth indication is not accurate for larger objects; however,

it will provide accurate relative depth indications. The greater the distance an

object is from the search coil, the greater

its depth value.

Pressing this touch pad will cause

the detector to toggle between two

operating modes, DISCRIMINATION and

ALL-METAL. If the detector is in the

ALL-METAL mode (the default mode),

pressing the touch pad will change the detector into DISCRIMINATION mode.

If the detector is in the DISCRIMINATION mode, pressing the touch pad will

change the detector into ALL-METAL mode

Discrimination is used to eliminate unwanted objects from detection.

To enter this mode, from ALL-METAL mode, press the DISC/A-M touch pad.

After pressing

DISC/A-M, the detector will:

• Beep twice

• Display 3

"R"s under the left-most segments, Iron 1, 2 & 3

Ferrous objects will not be detected in DISCRIMINATION mode.

Heavily oxidized ferrous objects and very large iron objects will sometimes,

however, be detected, usually with a high tone and an indication to the right

of the target indentification scale.

To increase the level of discrimination, press the DISCRIMINATION

touch

pad. Each time the pad is depressed, an additional "R" will appear, thus

eliminating from detection the objects which fall into the corresponding

categories.

To decrease the level of discrimination, press the DISCRIMINATION

▼ touch pad. Each time the ▼ pad is depressed, an illuminated "R"

will disappear, thus returning to detection the objects which fall into the

corresponding categories.

Discrimination Mode is a fixed-start-point elimination system. Objects are

cumulatively eliminated as the level of discrimination increases.

Accurate pinpointing takes practice

and is best accomplished by “X-ing”

the target area.

1. Once a buried target is indicated by

a good tone response, continue

sweeping the coil over the target

in a narrowing side-to-side pat-

tern.

2. Take visual note of the place on the

ground where the “beep” sounds.

3. Stop the coil directly over this spot

on the ground.

4. Now move the coil straight for-

ward and straight back towards

you a couple of times.

5. Again make visual note of the spot

on the ground at which the “beep”

sounds.

6. If needed, “X” the target at

different angles to “zero in” on the

exact spot on the ground at which

the “beep” sounds.

When swinging the coil, be careful

to keep it level with the ground about

one inch from the surface. Never

swing the coil like a pendulum.

WRONG

CORRECT

NOTE: This modern Metal Detector is referred to as a Motion Detector since it can

respond to a target only while the searchcoil is being moved over the Target.