Bolens 13AN76TS565 Le manuel du propriétaire

Marque: Bolens

Modèle: 13AN76TS565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

13AM76TF565

o p e r a t o r ’s m a n u a l

Printed In USA

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

Model Series 760-770 Lawn Tractor

P. O. Box 1386, 97 Kent Avenue, KITCHENER, ONTARIO, CANADA N2G 4J1

769-06893

01.19.11

Customer Support

Please do

NOT

return the unit to the retailer from which it was purchased, without first contacting Customer Support.

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of

this machine, you can seek help from the experts. Choose from the options below:

Visit our web at www.bolens.ca◊

Locate your nearest dealer from Customer Support: 1-800-668-1238◊

Contact MTD CANADA • P.O. Box 1386 • 97 Kent Avenue • Kitchener, Ontario, Canada • N2G 4J1◊

To The Owner

Safe Operation Practices ........................................ 3

Assembly & Set-Up .................................................. 9

Controls & Features ................................................12

Operation ................................................................15

Maintenance & Adjustment..................................19

Service .................................................................... 24

Troubleshooting .................................................... 28

Attachments & Accessories .................................. 29

Replacement Parts ................................................ 30

Warranty .................................................................31

Emission control warranty statement ................. 32

Table of Contents

Thank you for purchasing your new equipment. It was carefully

engineered to provide excellent performance when properly

operated and maintained.

Please read this entire manual prior to operating the equipment.

It instructs you how to safely and easily set up, operate and

maintain your machine. Please be sure that you, and any other

persons who will operate the machine, carefully follow the

recommended safety practices at all times. Failure to do so could

result in personal injury or property damage.

All information in this manual is relative to the most recent

product information available at the time of printing. Review

this manual frequently to familiarize yourself with the machine,

its features and operation. Please be aware that this Operator’s

Manual may cover a range of product specifications for

various models. Characteristics and features discussed and/or

illustrated in this manual may not be applicable to all models.

The manufacturer reserves the right to change product

specifications, designs and equipment without notice and

without incurring obligation.

If you have any problems or questions concerning the machine,

phone your local service dealer or contact us directly. Customer

Support telephone numbers, website address and mailing

address can be found on this page. We want to ensure your

complete satisfaction at all times.

Throughout this manual, all references to right and left side of the

machine are observed from the operating position.

The engine manufacturer is responsible for all engine-related

issues with regards to performance, power-rating, specifications,

warranty and service. Please refer to the engine manufacturer’s

Owner’s/Operator’s Manual, packed separately with your

machine, for more information.

Thank You

Record Product Information

Before setting up and operating your new equipment, please

locate the model plate on the equipment and record the

information in the provided area to the right. You can locate the

model plate under the operator’s seat. Flip the seat forward to

view the model plate. This information will be necessary, should

you seek technical support via our web site or with your local

dealer.

mo d e l nu m b e r

se r i a l nu m b e r

Important Safe Operation Practices

General Operation

Read, understand, and follow all instructions on the 1.

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place for

future and regular reference and for ordering replacement

parts.

Be familiar with all controls and their proper operation. 2.

Know how to stop the machine and disengage them

quickly.

Never allow children under 14 years of age to operate this 3.

machine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the machine and should be trained and supervised

by an adult.

Never allow adults to operate this machine without proper 4.

instruction.

To help avoid blade contact or a thrown object injury, 5.

keep bystanders, helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop machine if

anyone enters the area.

Thoroughly inspect the area where the equipment is to be 6.

used. Remove all stones, sticks, wire, bones, toys, and other

foreign objects which could be picked up and thrown by

the blade(s). Thrown objects can cause serious personal

injury.

Plan your mowing pattern to avoid discharge of material 7.

toward roads, sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or obstruction

which may cause discharged material to ricochet back

toward the operator.

Always wear safety glasses or safety goggles during 8.

operation and while performing an adjustment or repair

to protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate this machine. Failure to comply

with these instructions may result in personal injury.

When you see this symbol. HEED ITS WARNING!

DANGER! This machine was built to be operated according to the safe operation practices in

this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating hands and feet

and throwing objects. Failure to observe the following safety instructions could result in

serious injury or death.

Wear sturdy, rough-soled work shoes and close-fitting 9.

slacks and shirts. Loose fitting clothes and jewelry can be

caught in movable parts. Never operate this machine in

bare feet or sandals.

Be aware of the mower and attachment discharge direction 10.

and do not point it at anyone. Do not operate the mower

without the discharge cover or entire grass catcher in its

proper place.

Do not put hands or feet near rotating parts or under the 11.

cutting deck. Contact with the blade(s) can amputate

hands and feet.

A missing or damaged discharge cover can cause blade 12.

contact or thrown object injuries.

Stop the blade(s) when crossing gravel drives, walks, or 13.

roads and while not cutting grass.

Watch for traffic when operating near or crossing 14.

roadways. This machine is not intended for use on any

public roadway.

Do not operate the machine while under the influence of 15.

alcohol or drugs.

Mow only in daylight or good artificial light.16.

Never carry passengers.17.

Disengage blade(s) before shifting into reverse. Back up 18.

slowly. Always look down and behind before and while

backing to avoid a back-over accident.

Slow down before turning. Operate the machine smoothly. 19.

Avoid erratic operation and excessive speed.

Disengage blade(s), set parking brake, stop engine and 20.

wait until the blade(s) come to a complete stop before

removing grass catcher, emptying grass, unclogging chute,

removing any grass or debris, or making any adjustments.

Never leave a running machine unattended. Always turn 21.

off blade(s), place transmission in neutral, set parking

brake, stop engine and remove key before dismounting.

4 se c t i o n 2 — im p o r t a n t sa f e op e r a t i o n pr a c t i c e s

Use extra care when loading or unloading the machine into 22.

a trailer or truck. This machine should not be driven up or

down ramp(s), because the machine could tip over, causing

serious personal injury. The machine must be pushed

manually on ramp(s) to load or unload properly.

Muffler and engine become hot and can cause a burn. Do 23.

not touch.

Check overhead clearances carefully before driving under 24.

low hanging tree branches, wires, door openings etc.,

where the operator may be struck or pulled from the

machine, which could result in serious injury.

Disengage all attachment clutches, depress the brake 25.

pedal completely and shift into neutral before attempting

to start engine.

Your machine is designed to cut normal residential grass of 26.

a height no more than 10”. Do not attempt to mow through

unusually tall, dry grass (e.g., pasture) or piles of dry leaves.

Dry grass or leaves may contact the engine exhaust and/or

build up on the mower deck presenting a potential fire

hazard.

Use only accessories and attachments approved for this 27.

machine by the machine manufacturer. Read, understand

and follow all instructions provided with the approved

accessory or attachment.

Data indicates that operators, age 60 years and above, are 28.

involved in a large percentage of riding mower-related

injuries. These operators should evaluate their ability

to operate the riding mower safely enough to protect

themselves and others from serious injury.

If situations occur which are not covered in this manual, use 29.

care and good judgment. Contact your customer service

representative for assistance.

Slope Operation

Slopes are a major factor related to loss of control and tip-over

accidents which can result in severe injury or death. All slopes

require extra caution. If you cannot back up the slope or if you

feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of this

manual to measure slopes before operating this machine on

a sloped or hilly area. If the slope is greater than 15 degrees as

shown on the slope gauge, do not operate this machine on that

area or serious injury could result.

Do:

Mow up and down slopes, not across. Exercise extreme 1.

caution when changing direction on slopes.

Watch for holes, ruts, bumps, rocks, or other hidden 2.

objects. Uneven terrain could overturn the machine. Tall

grass can hide obstacles.

Use slow speed. Choose a low enough speed setting so 3.

that you will not have to stop or shift while on the slope.

Tires may lose traction on slopes even though the brakes

are functioning properly. Always keep machine in gear

when going down slopes to take advantage of engine

braking action.

Follow the manufacturer’s recommendations for wheel 4.

weights or counterweights to improve stability.

Use extra care with grass catchers or other attachments. 5.

These can change the stability of the machine.

Keep all movement on the slopes slow and gradual. Do 6.

not make sudden changes in speed or direction. Rapid

engagement or braking could cause the front of the

machine to lift and rapidly flip over backwards which could

cause serious injury.

Do Not:

Do not turn on slopes unless necessary; then, turn slowly 1.

and gradually downhill, if possible.

Do not mow near drop-offs, ditches or embankments. The 2.

mower could suddenly turn over if a wheel is over the edge

of a cliff, ditch, or if an edge caves in.

Do not try to stabilize the machine by putting your foot on 3.

the ground.

Do not use a grass catcher on steep slopes. 4.

Do not mow on wet grass. Reduced traction could cause 5.

sliding.

Do not tow heavy pull behind attachments (e.g. loaded 6.

dump cart, lawn roller, etc.) on slopes greater than 5

degrees. When going down hill, the extra weight tends

to push the tractor and may cause you to loose control

(e.g. tractor may speed up, braking and steering ability are

reduced, attachment may jack-knife and cause tractor to

overturn).

5se c t i o n 2 — im p o r t a n t sa f e op e r a t i o n pr a c t i c e s

Children

Tragic accidents can occur if the operator is not alert to the 1.

presence of children. Children are often attracted to the

machine and the mowing activity. They do not understand

the dangers. Never assume that children will remain where

you last saw them.

Keep children out of the mowing area and in a.

watchful care of a responsible adult other than the

operator.

Be alert and turn machine off if a child enters the b.

area.

To avoid back-over accidents, look behind and down c.

for small children.

Never carry children, even with the blade(s) shut off. d.

They may fall off and be seriously injured or interfere

with safe machine operation.

Use extreme care when approaching blind corners, e.

doorways, shrubs, trees or other objects that may

block your vision of a child who may run into the

path of the machine.

Keep children away from hot or running engines. f.

They can suffer burns from a hot muffler.

Remove key when machine is unattended to g.

prevent unauthorized operation.

Never allow children under 14 years of age to operate this 2.

machine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the machine and should be trained and supervised

by an adult.

Towing

Tow only with a machine that has a hitch designed for 1.

towing. Do not attach towed equipment except at the

hitch point.

Follow the manufacturers recommendation for weight 2.

limits for towed equipment and towing on slopes.

Never allow children or others in or on towed equipment.3.

On slopes, the weight of the towed equipment may cause 4.

loss of traction and loss of control.

Travel slowly and allow extra distance to stop.5.

Do not shift to neutral and coast downhill. 6.

Service

Safe Handling of Gasoline:

To avoid personal injury or property damage use extreme 1.

care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious

personal injury can occur when gasoline is spilled on

yourself or your clothes which can ignite. Wash your skin

and change clothes immediately.

Use only an approved gasoline container.a.

Never fill containers inside a vehicle or on a truck b.

or trailer bed with a plastic liner. Always place

containers on the ground away from your vehicle

before filling.

When practical, remove gas-powered equipment c.

from the truck or trailer and refuel it on the ground.

If this is not possible, then refuel such equipment on

a trailer with a portable container, rather than from a

gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel d.

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

Extinguish all cigarettes, cigars, pipes and other e.

sources of ignition.

Never fuel machine indoors.f.

Never remove gas cap or add fuel while the engine g.

is hot or running. Allow engine to cool at least two

minutes before refueling.

Never over fill fuel tank. Fill tank to no more than ½ h.

inch below bottom of filler neck to allow space for

fuel expansion.

Replace gasoline cap and tighten securely.i.

If gasoline is spilled, wipe it off the engine and j.

equipment. Move machine to another area. Wait 5

minutes before starting the engine.

To reduce fire hazards, keep machine free of grass, k.

leaves, or other debris build-up. Clean up oil or fuel

spillage and remove any fuel soaked debris.

Never store the machine or fuel container inside l.

where there is an open flame, spark or pilot light

as on a water heater, space heater, furnace, clothes

dryer or other gas appliances.

Allow a machine to cool at least five minutes before m.

storing.

General Service

Never run an engine indoors or in a poorly ventilated area. 1.

Engine exhaust contains carbon monoxide, an odorless,

and deadly gas.

Before cleaning, repairing, or inspecting, make certain the 2.

blade(s) and all moving parts have stopped. Disconnect the

spark plug wire and ground against the engine to prevent

unintended starting.

6 se c t i o n 2 — im p o r t a n t sa f e op e r a t i o n pr a c t i c e s

Periodically check to make sure the blades come to 3.

complete stop within approximately (5) five seconds after

operating the blade disengagement control. If the blades

do not stop within the this time frame, your machine

should be serviced professionally by an authorized Service

Dealer.

Check brake operation frequently as it is subjected to wear 4.

during normal operation. Adjust and service as required.

Check the blade(s) and engine mounting bolts at frequent 5.

intervals for proper tightness. Also, visually inspect blade(s)

for damage (e.g., excessive wear, bent, cracked). Replace

the blade(s) with the original equipment manufacturer’s

(O.E.M.) blade(s) only, listed in this manual. “Use of parts

which do not meet the original equipment specifications

may lead to improper performance and compromise

safety!”

Mower blades are sharp. Wrap the blade or wear gloves, 6.

and use extra caution when servicing them.

Keep all nuts, bolts, and screws tight to be sure the 7.

equipment is in safe working condition.

Never tamper with the safety interlock system or other 8.

safety devices. Check their proper operation regularly.

After striking a foreign object, stop the engine, disconnect 9.

the spark plug wire(s) and ground against the engine.

Thoroughly inspect the machine for any damage. Repair

the damage before starting and operating.

Never attempt to make adjustments or repairs to the 10.

machine while the engine is running.

Grass catcher components and the discharge cover are 11.

subject to wear and damage which could expose moving

parts or allow objects to be thrown. For safety protection,

frequently check components and replace immediately

with original equipment manufacturer’s (O.E.M.) parts only,

listed in this manual. “Use of parts which do not meet the

original equipment specifications may lead to improper

performance and compromise safety!”

Do not change the engine governor settings or over-speed 12.

the engine. The governor controls the maximum safe

operating speed of the engine.

Maintain or replace safety and instruction labels, as 13.

necessary.

Observe proper disposal laws and regulations for gas, oil, 14.

etc. to protect the environment.

According to the Consumer Products Safety Commission 15.

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an Average Useful Life of seven (7) years,

or 270 hours of operation. At the end of the Average Useful

Life have the machine inspected annually by an authorized

service dealer to ensure that all mechanical and safety

systems are working properly and not worn excessively.

Failure to do so can result in accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and

may include the following emission control systems: Engine

Modification (EM), Oxidizing Catalyst (OC), Secondary Air

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! This machine is equipped with an

internal combustion engine and should not be used

on or near any unimproved forest-covered,

brushcovered or grass-covered land unless the

engine’s exhaust system is equipped with a spark

arrester meeting applicable local or state laws (if

any).

If a spark arrester is used, it should be maintained in effective

working order by the operator.

A spark arrester for the muffler is available through your nearest

engine authorized service dealer.

WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

7se c t i o n 2 — im p o r t a n t sa f e op e r a t i o n pr a c t i c e s

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the

machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate

WARNING— ROTATING BLADES

Do not put hands or feet near rotating parts or under the cutting deck. Contact with the

blade(s) can amputate hands and feet.

WARNING—THROWN OBJECTS

This machine may pick up and throw and objects which can cause serious personal injury.

WARNING—THROWN OBJECTS

This machine may pick up and throw and objects which can cause serious personal injury.

BYSTANDERS

Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in

operation.

WARNING— SLOPE OPERATION

Do not operate this machine on a slope greater than 15 degrees.

DANGER — ROTATING BLADES

To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover

or grass catcher is in its proper place. If damaged, replace immediately.

8 Se c t i o n 2 — im p o r t a n t Sa f e op e r a t i o n pr a c t i c e S

15°

Sight and hold this level with a vertical tree...

or a corner of a building...

or a fence post

Fold along dotted line (representing a 15° slope)

Use this page as a guide to determine slopes where you may not operate safely.

WARNING! Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees

(a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding

mowers up and down slopes, never across the face of slopes.

Assembly & Set-Up

Tractor Set-Up

NOTE: This Operators Manual covers a range of product

specifications for various models. Characteristics and features

discussed and/or illustrated in this manual may not be applicable

to all models. The manufacturer reserves the right to change

product specifications, designs and equipment without notice

and without incurring obligation.

Connecting the Battery Cables

CALIFORNIA PROPOSITION 65 WARNING:

Battery posts, terminals, and related accessories

contain lead and lead compounds, chemicals known

to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

CAUTION: When attaching battery cables, always

connect the POSITIVE (Red) wire to its terminal first,

followed by the NEGATIVE (Black) wire.

For shipping reasons, both battery cables on your equipment

may have been left disconnected from the terminals at the

factory. To connect the battery cables, proceed as follows:

NOTE: The positive battery terminal is marked Pos. (+). The

negative battery terminal is marked Neg. (–).

Remove the plastic cover, if present, from the positive 1.

battery terminal and attach the red cable to the positive

battery terminal (+) with the bolt and hex nut. See Fig. 3-1.

Remove the plastic cover, if present, from the negative 2.

battery terminal and attach the black cable to the negative

battery terminal (–) with the bolt and hex nut. See Fig. 3-1.

Position the red rubber boot over the positive battery 3.

terminal to help protect it from corrosion.

NOTE: If the battery is put into service after the date shown

on top/side of battery, charge the battery as instructed in the

Maintenance section your Operator’s Manual prior to operating

the tractor.

Shipping Brace Removal

WARNING! Make sure the riding mower’s engine is

off, remove the ignition key, and set the parking

brake before removing the shipping brace. Refer to

the Controls and Features section for instructions on

how to set the parking brake.

Locate the shipping brace, if present, and accompanying •

warning tag found on the right side of the mower, between

the discharge chute and the cutting deck. See Fig. 3-2.

Place the deck lift lever in the highest cutting position. •

Refer to Setting the Cutting Height in the Operation

section of this manual.

While pushing the discharge chute towards the machine •

with your left hand, remove the shipping brace with your

right hand by grasping it between your thumb and index

finger and rotating it clockwise.

WARNING! The shipping brace, used for packaging

purposes only, must be removed and discarded

before operating your riding mower.

WARNING! The mowing deck is capable of

throwing objects. Failure to operate the riding

mower with the discharge cover in the proper

operating position could result in serious personal

injury and/or property damage.

Figure 3-1

Figure 3-2

Assembly & Set-Up

10 se c t i o n 3— as s e m b l y & se t -up

Attaching The Seat

If the seat for your tractor was not attached at the factory, follow

the applicable instructions below to attach it.

NOTE: For shipping reasons, some seats are not attached at

the factory. In this is the case, free the seat from its shipping

position and remove the hex screw (or knob screw if applicable)

from the bottom of seat before proceeding with the following

instructions.

Position the seat facing forward over the seat pivot bracket, 1.

with the two forward seat mount tabs fitting into the

provided grooves in the seat pivot bracket.

Slide the seat rearward and align the center mounting 2.

hole in the seat with the slot in the seat pan. Insert the hex

screw (or knob screw if applicable) previously removed. Do

not tighten at this point.

Adjust the seat to the optimal operator preferred location, 3.

this may mean actually sitting in the seat to decide what

feels best to the operator. Keep in mind the operator needs

to be able to fully operate all pedals comfortably while

sitting back in the seat.

Tighten the hex screw (or knob screw if applicable) at this 4.

time.

To adjust the position of the seat, loosen the hex screw (or 5.

knob screw if applicable) on the bottom of the seat. Slide

the seat forward or backward as desired. Retighten the hex

screw (or knob screw if applicable). See Fig. 3-5.

Knob Screw

Adjust

Hex Screw

Adjust

Attaching The Steering Wheel

If the steering wheel for your tractor did not come attached, the

hardware for attaching it has been packed within the steering

wheel, beneath the steering wheel cap. Carefully pry off the

steering wheel cap and remove the hardware.

NOTE: There are two different syles of steering wheel caps.

Styles vary by model.

With the wheels of the tractor pointing straight forward, 1.

place the steering wheel over the steering shaft.

Place the washer (with the cupped side down) over the 2.

steering wheel and secure with the hex bolt. See Fig. 3-3.

Place the steering wheel cap over the center of the steering 3.

wheel and push downward until it “clicks” into place.

Attaching The Dash Collar

If the tractor’s dash collar did not come attached from the

factory, the screws for attaching it can be found in either side of

the dash console. Remove the two screws from the console and

secure the dash collar as illustrated in Fig 3-4.

Figure 3-3

Figure 3-4

Figure 3-5

11se c t i o n 3 — as s e m b l y & se t -up

Mulch Plug (optional)

Note: See the Attachments & Accessories section if you would

like information regarding adding a mulching system for your

model of tractor.

Tire Pressure

WARNING! Maximum tire pressure under any

circumstances is 30 psi. Equal tire pressure should be

maintained at all times. Never exceed the maximum

inflation pressure shown on the sidewall of the tire.

The recommended operating tire pressure is:

Approximately 10 psi for the rear tires •

Approximately 14 psi for the front tires•

IMPORTANT: Refer to the tire sidewall for exact tire

manufacturer’s recommended or maximum psi. Do not

overinflate. Uneven tire pressure could cause the cutting deck to

mow unevenly.

Gas and Oil Fill-up

The gasoline tank is located under the hood. Do not overfill.

WARNING! Use extreme care when handling

gasoline. Gasoline is extremely flammable and the

vapors are explosive. Never fuel machine indoors or

while the engine is hot or running. Extinguish

cigarettes, cigars, pipes, and other sources of ignition.

Service the engine with gasoline and oil as instructed in the

separate Engine Operator/Owner Manual packed with your

tractor. Read the instructions carefully.

IMPORTANT: Your tractor is shipped with motor oil in the

engine. However, you MUST check the oil level before

operating. Be careful not to overfill.

IMPORTANT: It is important to NOT top off your fuel tank

when filling with fuel. Leave an expansion area available inside

the fuel tank to allow for the fuel to expand and for proper

ventilation. Otherwise the unit may not run properly. Fill the tank

in accordance with Figure 3-6.

Setting the Deck Gauge Wheels (if so equipped)

Move the tractor on a firm and level surface, preferably

pavement, and proceed as follows

Select the height position of the cutting deck by placing 1.

the deck lift lever in the normally desired mowing height

setting (any of the six different cutting height notches on the

right fender).

Check the gauge wheels for contact or excessive clearance 2.

with the surface below. The deck gauge wheels should

have between ¼-inch and ½-inch clearance above the

ground as follows:

If the gauge wheels have excessive clearance or contact with the

surface, adjust as follows:

Raise the deck lift handle to its highest setting.a.

Remove the gauge wheels by removing the lock b.

nuts and shoulder screws which secure them to the

deck. See Fig. 3-7.

Place the deck lift lever in the desired mowing c.

height setting.

Reinsert the shoulder screw (with each gauge d.

wheel) into the index hole that leaves approximately

½-inch between the bottom of the wheel and the

pavement.

Refer to Leveling the Deck in the Maintenance section of this

manual for more detailed instructions regarding various deck

adjustments.

Figure 3-7

Figure 3-6

Figure 4-1

Speed Control &

Parking Brake Lever

Clutch/Brake Pedal

Shift Lever

Throttle/Choke Lever

Deck Lift Lever

PTO (Blade Engage) Lever

Ignition Switch

Module

Choke Knob

(optional)

Ammeter (optional)

Controls and Features

Lawn Tractor controls and features are illustrated in Fig 4-1 and described on the following pages.

WARNING! Read and follow all safety rules and instructions in this manual, including the entire Operation section,

before attempting to operate this machine. Failure to comply with all safety rules and instructions may result in personal

injury.

Throttle Control Lever

The throttle control lever is located on the right side of the

tractor’s dash panel. This lever controls the speed of the engine

and, on some models, when pushed all the way forward, the

choke control also. When set in a given position, the throttle will

maintain a uniform engine speed. See Fig. 4-2.

IMPORTANT: When operating the tractor with the cutting deck

engaged, be certain that the throttle lever is always in the FAST

(rabbit) position.

Choke Control

On some models, moving the throttle

lever all the way forward activates the

engine’s choke control. On all other

models, the choke control can be found

on the left side of the dash panel and is

activated by pulling the knob outward.

Activating the choke control closes the

choke plate on the carburetor and aids in

starting the engine. Refer to Starting The

Engine in the Operation section of this

manual for detailed starting instructions.

Ignition Switch

Your new lawn tractor will have one of the following ignition

switches. Use Fig. 4-3 to identify which switch your machine

utilizes and follow these instructions for proper operation.

3-Position Ignition Switch

The ignition switch is activated to start the engine. Insert key

into the ignition switch and turn clockwise to the START position.

Release the key into the ON position once engine has fired. See

Fig. 4-3A. The engine will run with the headlights on.

To stop the engine, turn the ignition key counterclockwise to the

OFF position. See Fig. 4-3A.

4-Position Ignition Switch

The ignition switch is activated to start the engine. Insert key

into the ignition switch and turn clockwise to the START position.

Release the key into the ON position once engine has fired.

See Fig. 4-3B. The engine will run with the headlights off in

this position. To activate the headlights, turn the key one more

position to the left. The engine will continue to run with the

headlights on.

FAST

SLOW

CHOKE

FAST

SLOW

Figure 4-2

Figure 4-3

Off

On/Lights

Start

Off

On/Lights

Start

Stop

Position

Normal

Mowing

Start

Position

Reverse

Caution Mode

13se c t i o n 4 — co n t r o l s a n d fe a t u r e s

To stop the engine, turn the ignition key counterclockwise to the

OFF position. See Fig. 4-3B.

Ignition Switch Module

To start the engine, insert the key into the ignition switch and

turn clockwise to the START position. Release the key into the

NORMAL MOWING MODE position once the engine has fired. The

headlights will be activated in the Normal (and Reverse Caution

Modes).

To stop the engine, turn the ignition key counterclockwise to the

OFF position. See Fig. 4-3C.

WARNING! Never leave a running machine

unattended. Always disengage PTO, move shift lever

into neutral position, set parking brake, stop engine

and remove key to prevent unintended starting.

IMPORTANT: Prior to operating the tractor, refer to both Safety

Interlock Switches and Starting The Engine in the Operation

section of this manual for detailed instructions regarding the

Ignition Switch Module and operating the tractor in REVERSE

CAUTION MODE.

Clutch-Brake Pedal

The clutch-brake pedal is located on the left side of the lawn

tractor, along the running board. Depress the clutch-brake pedal

part way down when slowing the tractor by changing speeds

(Refer to Speed Control Lever). Depress the pedal all the way down

to engage the disc brake and bring the tractor to a complete

stop.

NOTE: The pedal must be depressed to start the engine. Refer to

Safety Interlock Switches in the Operation section of this manual.

Parking Brake

To set the parking brake, fully depress the clutch-brake pedal.

Move the speed control lever all the way down and into the

parking brake position. Release the clutch-brake pedal to allow

the parking brake to engage.

To release the parking brake, depress the clutch-brake pedal and

move the speed control lever out of the notches to the desired

position. Release the speed control lever and the clutch-brake

pedal.

NOTE: The parking brake must be set if the operator leaves the

seat with the engine running or the engine will automatically

shut off.

Shift Lever

The shift lever is located on the left side of the fender and has

three positions, FORWARD, NEUTRAL and REVERSE. The brake

pedal must be depressed and the tractor must not be in motion

when the moving shift lever. See Fig. 4-4.

IMPORTANT: Never force the shift lever. Doing so may result in

serious damage to the tractor’s transmission.

Speed Control Lever

The speed control lever, located on the left side of

the tractor’s dash console, allows you to regulate

the ground speed of the lawn tractor. To use,

depress the clutch-brake pedal and move the lever

out of the parking brake notch and forward to

increase the tractor’s ground speed. When a desired

speed has been reached, release the lever into an

appropriate notch to maintain that speed.

To slow the tractor’s ground speed, depress the

clutch-brake pedal and move the speed control

lever rearward and release it into a notch.

NOTE: Lawn tractors vary by model and are

available with either a 6- or 7-speed control lever.

PTO (Blade Engage) Lever

Found on the tractor’s right fender, the PTO (blade

engage) lever is used to engage power to the cutting

deck or other (separately available) attachments.

To operate, move the lever all the way forward.

Moving the lever all the way rearward into the PTO

OFF position disengages power to the cutting deck/

attachment.

NOTE: The PTO (blade engage) lever must be in the

disengaged (PTO OFF) position when starting the

engine.

Deck Lift Lever

Found on your tractor’s right fender, the deck lift lever

is used to change the height of the cutting deck. To

use, move the lever to the left, then place in the notch

best suited for your application.

Figure 4-4

14 se c t i o n 4 — co n t r o l s a n d fe a t u r e s

Operation

Safety Interlock Switches

This tractor is equipped with a safety interlock system for the

protection of the operator. If the interlock system should ever

malfunction, do not operate the tractor. Contact an authorized

MTD service dealer.

The safety interlock system prevents the engine from •

cranking or starting unless the parking brake is engaged,

and the PTO (Blade Engage) lever is in the disengaged (OFF)

position.

The engine will automatically shut off if the operator leaves •

the seat before engaging the parking brake.

The engine will automatically shut off if the operator leaves •

the tractor’s seat with the PTO (Blade Engage) lever in the

engaged (ON) position, regardless of whether the parking

brake is engaged.

Models without Reverse Caution Mode

The engine will automatically shut off if the PTO • (Blade

Engage) lever is moved into the engaged (ON) position with

the shift lever in Reverse.

Models with Reverse Caution Mode

With the ignition key in the NORMAL MOWING position, the •

engine will automatically shut off if the PTO (Blade Engage)

lever is moved into the engaged (ON) position with the shift

lever in Reverse.

WARNING! Do not operate the tractor if the

interlock system is malfunctioning. This system was

designed for your safety and protection.

Reverse Caution Mode

(Models equipped with ignition switch module)

WARNING! Use extreme caution while operating

the tractor in the REVERSE CAUTION MODE. Always

look down and behind before and while backing. Do

not operate the tractor when children or others are

around. Stop the tractor immediately if someone

enters the area.

The REVERSE CAUTION MODE position of the key switch

module allows the tractor to be operated in reverse with the

blades (PTO) engaged.

IMPORTANT: Mowing in reverse is not recommended.

To use the REVERSE CAUTION MODE:

IMPORTANT: The operator MUST be seated in the tractor seat.

Start the engine as instructed in the Operation section of 1.

this manual.

Turn the key from the NORMAL MOWING 2. (Green) position

to the REVERSE CAUTION MODE (Yellow) position of the key

switch module. See Fig. 5-1.

Depress the REVERSE PUSH BUTTON 3. (Orange, Triangular

Button) at the top, right corner of the key switch module. The

red indicator light at the top, left corner of the key switch

module will be ON while activated. See Fig. 5-1.

Stop

position

Start

position

Indicator

Light

Reverse

Push

Button

Normal

Driving

Mode

Reverse

Caution

Mode

Position

Figure 5-1

Operation

16 se c t i o n 5— op e r a t i o n

Once activated 4. (indicator light ON), the tractor can be driven

in reverse with the cutting blades (PTO) engaged.

Always look down and behind before and while backing to 5.

make sure no children are around.

After resuming forward motion, return the key to the 6.

NORMAL MOWING position.

IMPORTANT: The REVERSE CAUTION MODE will remain

activated until:

The key is placed in either the NORMAL MOWING a.

position or STOP position.

The operator engages the parking brake by fully b.

depressing the clutch-brake pedal and holding it down

while moving the speed control lever into the PARK

BRAKE position.

Engaging the Parking Brake

To engage the parking brake:

Fully depress the clutch-brake pedal and hold it down with 1.

your foot.

Move the speed control lever all the way down and into the 2.

parking brake position.

Release the clutch-brake pedal to allow the parking brake to 3.

engage.

To release the parking brake:

Depress the clutch-brake pedal and move the speed control 1.

lever out of the parking brake position and into a desired

speed.

Setting the Cutting Height

Select the height position of the cutting deck by placing 1.

the deck lift lever in any of the six different cutting height

notches on the right side of the fender.

Adjust the deck wheels as instructed in the Assembly & Set-2.

Up section earlier in this manual, if equipped, so that they

are between ¼-inch and ½-inch above the ground when the

tractor is on a smooth, flat surface such as a driveway.

WARNING! Keep hands and feet away from the

discharge opening of the cutting deck.

NOTE: On models so equipped, the deck wheels are an anti-scalp

feature of the deck and are not designed to support the weight

of the cutting deck. Refer to Leveling in the Maintenance section

of this manual for more detailed instructions regarding various

deck adjustments.

Starting the Engine

WARNING! Do not operate the tractor if the

interlock system is malfunctioning. This system was

designed for your safety and protection.

NOTE: Refer to the Gasoline and Oil fill-up instructions in the

Assembly & Set-up section of this manual.

Insert the tractor key into the ignition switch.1.

Place the PTO 2. (Blade Engage) lever in the disengaged (OFF)

position.

Engage the tractor’s parking brake.3.

Activate the choke control.4.

Turn the ignition key clockwise to the START position. After 5.

the engine starts, release the key. It will return to the ON (or

Normal Mowing) position.

CAUTION: Do NOT hold the key in the START

position for longer than ten seconds at a time. Doing

so may cause damage to your engine’s electric

starter.

After the engine starts, deactivate the choke control and 6.

place the throttle control in the FAST position.

NOTE: Do NOT leave the choke control on while operating the

tractor. Doing so will result in a “rich” fuel mixture and cause the

engine to run poorly.

Stopping the Engine

WARNING! If you strike a foreign object, stop the

engine, disconnect the spark plug wire(s) and

ground against the engine. Thoroughly inspect the

machine for any damage. Repair the damage before

restarting and operating

If the blades are engaged, place the PTO 1. (Blade Engage) lever

in the disengaged (OFF) position.

Turn the ignition key counterclockwise to the STOP position. 2.

Remove the key from the ignition switch to prevent 3.

unintended starting.

17se c t i o n 5 — op e r a t i o n

Driving The Tractor

WARNING! Avoid sudden starts, excessive speed

and sudden stops.

WARNING! Do not leave the seat of the tractor

without first placing the PTO (Blade Engage) lever in

the disengaged (OFF) position, depressing the brake

pedal and engaging the parking brake. If leaving

the tractor unattended, also turn the ignition key off

and remove the key.

WARNING! Always look down and behind before

and while backing up to avoid a back-over accident.

Depress the brake pedal to release the parking brake and let 1.

the pedal up.

Move the throttle lever into the FAST (rabbit) position.2.

Place the shift lever in either the FORWARD or REVERSE 3.

position.

IMPORTANT: Do NOT use the shift lever to change the

direction of travel when the tractor is in motion. Always use

the brake pedal to bring the tractor to a complete stop before

shifting.

Release the parking brake by depressing the clutch-brake 4.

pedal and positioning the speed control lever in desired

position.

IMPORTANT: First-time operators should use speed positions 1

or 2. Become completely familiar with the tractor’s operation and

controls before operating the tractor in higher speed positions.

Release clutch-brake pedal slowly to put unit into motion.5.

The lawn tractor is brought to a stop by depressing the 6.

clutch-brake pedal.

NOTE: When operating the unit initially, there will be little

difference between the highest two speeds until after the belts

have seated themselves into the pulleys during the break-in

period.

WARNING! Before leaving the operator’s position

for any reason, disengage the blades, place the shift

lever in neutral, engage the parking brake, shut

engine off and remove the key.

IMPORTANT: When stopping the tractor for any reason while

on a grass surface, always:

Place the shift lever in neutral, 1.

Engage the parking brake, 2.

Shut engine off and remove the key. Doing so will minimize 3.

the possibility of having your lawn ‘‘browned’’ by hot

exhaust from your tractor’s running engine.

If unit stalls with speed control in high speed, or if unit will

not operate with speed control lever in a low speed position,

proceed as follows:

Place shift lever in NEUTRAL.1.

Restart engine.2.

Place speed control lever in highest speed position.3.

Release clutch-brake pedal fully.4.

Depress clutch-brake pedal.5.

Place speed control lever in desired position.6.

Place shift lever in either FORWARD or REVERSE, and follow 7.

normal operating procedures.

Driving On Slopes

Refer to the SLOPE GAUGE in the Important Safe Operation

Practices section of the manual to help determine slopes where

you may operate the tractor safely.

WARNING! Do not mow on inclines with a slope in

excess of 15 degrees (a rise of approximately 2-1/2 feet

every 10 feet). The tractor could overturn and cause

serious injury.

Mow up and down slopes, NEVER across.•

Exercise extreme caution when changing direction on •

slopes.

Watch for holes, ruts, bumps, rocks, or other hidden objects. •

Uneven terrain could overturn the machine. Tall grass can

hide obstacles.

Avoid turns when driving on a slope. If a turn must be made, •

turn down the slope. Turning up a slope greatly increases

the chance of a roll over.

Avoid stopping when driving up a slope. If it is necessary •

to stop while driving up a slope, start up smoothly and

carefully to reduce the possibility of flipping the tractor over

backward.

Engaging the Blades

Engaging the PTO (Blade Engage) transfers power to the cutting

deck or other (separately available) attachments. To engage the

blades, proceed as follows:

Move the throttle control lever to the FAST (rabbit) position.1.

Grasp the PTO 2. (Blade Engage) lever and pivot it all the way

forward into the engaged (ON) position.

Keep the throttle lever in the FAST (rabbit) position for the 3.

most efficient use of the cutting deck or other (separately

available) attachments.

Models with Reverse Caution Mode:

The engine will automatically shut off if the PTO is engaged with

the shift lever in position for reverse travel with the ignition key

in the NORMAL MOWING position.

Models without Reverse Caution Mode:

The PTO (Blade Engage) lever must be in the disengaged (OFF)

position when starting the engine, when traveling in reverse, and

if the operator leaves the seat. Refer to Safety Interlock Switches

in the Operation section of this manual.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to the left, then

place it in the notch best suited for your application. Refer to

Setting The Cutting Height earlier in this section.

18 se c t i o n 5— op e r a t i o n

Mowing

WARNING! To help avoid blade contact or a

thrown object injury, keep bystanders, helpers,

children and pets at least 75 feet from the machine

while it is in operation. Stop machine if anyone

enters the area.

The following information will be helpful when using the cutting

deck with your tractor:

WARNING! Plan your mowing pattern to avoid

discharge of materials toward roads, sidewalks,

bystanders and the like. Also, avoid discharging

material against a wall or obstruction which may

cause discharged material to ricochet back toward

the operator.

Do not mow at high ground speed, especially if a mulch kit •

or grass collector is installed.

For best results it is recommended that the first two laps be •

cut with the discharge thrown towards the center. After the

first two laps, reverse the direction to throw the discharge to

the outside for the balance of cutting. This will give a better

appearance to the lawn.

Do not cut the grass too short. Short grass invites weed •

growth and yellows quickly in dry weather.

Mowing should always be done with the engine at full throttle. •

Under heavier conditions it may be necessary to go back •

over the cut area a second time to get a clean cut.

Do NOT attempt to mow heavy brush and weeds and •

extremely tall grass. Your tractor is designed to mow lawns,

NOT clear brush.

Keep the blades sharp and replace the blades when worn. •

Refer to Cutting Blades in the Service section of this manual

for proper blade sharpening instructions.

Mulching

Select models come equipped with a mulch kit which

incorporates special blades, already standard on the tractor, in a

process of recirculating grass clippings repeatedly beneath the

cutting deck. The ultra-fine clippings are then forced back into

the lawn where they act as a natural fertilizer.

Observe the following points for the best results when mulching:

Never attempt to mulch if the lawn is damp. Wet grass tends •

to stick to the underside of the cutting deck preventing

proper mulching of the clippings.

Do NOT attempt to mulch more than 1/3 the total height of •

the grass or approximately 1-1/2 inches. Doing so will cause

the clippings to clump up beneath the deck and not be

mulched effectively.

Maintain a slow ground speed to allow the grass clippings •

more time to effectively be mulched.

Always position the throttle control lever in the FAST (rabbit) •

position and allow it to remain there while mowing. Failing

to keep the engine at full throttle places strain on the

tractor’s engine and does not allow the blades to properly

mulch grass. Ground speed should be controlled using the

speed control lever.

NOTE: It is not necessary to remove the discharge chute to

operate the mower with the mulch kit installed.

WARNING! Never operate the mower without the

discharge chute properly attached.

To operate the cutting deck without mulching, simply remove

the mulch plug by unthreading the plastic wing nut which

fastens it to the cutting deck. This will allow the clippings to

discharge out the side. See Fig. 5-2.

Headlights

On some models, the lamps are ON whenever the tractor’s •

engine is running. On other models, the lamps are ON

whenever the ignition key is moved into the lights position,

with the engine running.

On all models, the lamps turn OFF when the ignition key is •

moved to the STOP position.

Figure 5-2

Maintenance

WARNING! Before performing any maintenance or

repairs, disengage PTO, move shift lever into neutral

position, set parking brake, stop engine and remove

key to prevent unintended starting.

Engine

Refer to the Engine Operator/Owner Manual for engine

maintenance instructions.

Check engine oil level before each use as instructed in the Engine

Operator/Owner Manual packed with your unit. Follow the

instructions carefully.

Changing Engine Oil and Filter

For draining oil from the engine’s crankcase of select model

tractors, a plastic oil drain sleeve or hose is packed with this

Operator’s Manual. See Figure 6-1.

Change the oil as instructed in the separate Engine 1.

Operator/Owner Manual packed with your unit.

Service the oil filter (if so equipped) as instructed in the 2.

separate Engine Operator/Owner Manual packed with your

unit.

Refill the engine with the proper quantity and weight of 3.

new motor oil as instructed in the Engine Operator/Owner

Manual packed with your unit.

Air Cleaner

Service the pre-cleaner, if so equipped, and cartridge/air cleaner

element as instructed in the Engine Operator/Owner Manual

packed with your unit.

Figure 6-1

Spark Plug

The spark plug should be cleaned and the gap reset once a

season. Spark plug replacement is recommended at the start

of each mowing season. Refer to the Engine Operator/Owner

Manual for correct plug type and gap specifications.

Lubrication

WARNING! Before lubricating, repairing, or

inspecting, always disengage PTO, move shift lever

into neutral position, set parking brake, stop engine

and remove key to prevent unintended starting.

Engine

Lubricate the engine with motor oil as instructed in the Engine

Owner Manual packed with your unit.

Pivot Points & Linkage

Lubricate all the pivot points on the drive system, parking brake

and lift linkage at least once a season with light oil.

Rear Wheels

The rear wheels should be removed from the axles once a

season. Lubricate the axles and the rims well with an all-purpose

grease before re-installing them.

Front Axles

Each end of the tractor’s front pivot bar may be equipped with a

grease fitting. Lubricate with a grease gun after every 25 hours of

tractor operation.

Battery

The battery is sealed and is maintenance-free. Acid levels cannot

be checked.

Always keep the battery cables and terminals clean and free •

of corrosive build-up.

After cleaning the battery and terminals, apply a light coat •

of petroleum jelly or grease to both terminals.

Always keep the rubber boot positioned over the positive •

terminal to prevent shorting.

IMPORTANT: If removing the battery for any reason,

disconnect the NEGATIVE (Black) wire from it’s terminal first,

followed by the POSITIVE (Red) wire. When re-installing the

battery, always connect the POSITIVE (Red) wire its terminal

first, followed by the NEGATIVE (Black) wire. Be certain that the

wires are connected to the correct terminals; reversing them

could change the polarity and result in damage to your engine’s

alternator system.

Cleaning Battery

Clean the battery by removing it from the tractor and washing

with a baking soda and water solution. If necessary, scrape the

battery terminals with a wire brush to remove deposits. Coat

terminals and exposed wiring with grease or petroleum jelly to

prevent corrosion.

Maintenance & Adjustments

Battery Failures

Some common causes for battery failure are:

Incorrect initial activation•

Overcharging•

Freezing•

Undercharging•

Corroded connections•

These failures are NOT covered by your tractor’s warranty.

Cleaning the Engine And Deck

Any fuel or oil spilled on the machine should be wiped off

promptly. Do NOT allow debris to accumulate around the cooling

fins of the engine or on any other part of the machine.

IMPORTANT: The use of a pressure washer to clean your

tractor is NOT recommended. It may cause damage to electrical

components, spindles, pulleys, bearings or the engine.

A hex plug can be found on your tractor’s deck surface. See Fig. 6-2.

This plug can be replaced with a water port to be used as part of

a separately-available deck wash system.

The Deck Wash System™ is used to rinse grass clippings from the

deck’s underside and prevent the buildup of corrosive chemicals.

NOTE: Refer to the Attachments & Accessories section of this

manual for information regarding this and other separately-

available attachments & accessories for your tractor.

Deck Wash System™

If your tractor’s deck is equipped with a water port on its surface

as part of its Deck Wash System™, follow these instructions to

utilize this feature.

Use the Deck Wash System™ to rinse grass clippings from the

deck’s underside and prevent the buildup of corrosive chemicals.

Complete the following steps AFTER EACH MOWING:

Drive the tractor to a level, clear spot on your lawn, near 1.

enough for your garden hose to reach.

CAUTION: Make certain the tractor’s discharge

chute is directed AWAY from your house, garage,

parked cars, etc.

Disengage the PTO 2. (Blade Engage), set the parking brake and

stop the engine.

Thread the hose coupler 3. (packaged with your tractor’s

Operator’s Manual) onto the end of your garden hose.

Attach the hose coupler to the water port on the deck’s 4.

surface. See Fig. 6-3.

Turn the water on.5.

While sitting in the operator’s position on the tractor, start 6.

the engine and place the throttle lever in the FAST (rabbit)

position.

Move the tractor’s PTO 7. (Blade Engage) into the ON position.

Remain in the operator’s position with the cutting deck 8.

engaged for a minimum of two minutes, allowing the

underside of the cutting deck to thoroughly rinse.

Move the tractor’s PTO 9. (Blade Engage) into the OFF position.

Turn the ignition key to the STOP position to turn the 10.

tractor’s engine off.

Turn the water off and detach the hose coupler from the 11.

water port on your deck’s surface.

On 46” decks, repeat steps 4 through 11 on the opposite 12.

side of the cutting deck.

Figure 6-3

Hex Plug

Figure 6-2

20 se c t i o n 6— ma i n t e n a n c e & ad j u s t m e n t s

La page est en cours de chargement...

Bolens 13AN76TS565 Le manuel du propriétaire

Marque: Bolens

Modèle: 13AN76TS565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

13AM76TF565

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 13AN76TS565 Owner's manual

Bolens 13AN76TS565 Le manuel du propriétaire

Ce manuel convient également à

Bolens 13AN76TS565 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents