DeWalt D55270 Manuel utilisateur

D55270, D55270T, D55271, D55271T, D55275, D55276

Contractor’s Gas Wheeled Portable Air Compressor

Compresseur d’air portatif à essence, sur roues, de classe entrepreneur

Compresor de aire portátil a gasolina con ruedas para contratistas

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

2

English

Air Compressor

A. Pump Air Intake Filter

B. Engine Air Filter

C. Engine On/Off Switch

D. Air Tank Pressure Gauge

E. Regulated Pressure Gauge

F. Pressure Regulator

G. Air Outlet

H. Unloader Valve

I. Safety Valve

J. Air Tank Drain Valve(s)

K. Pump Oil Dipstick/Oil Fill Plug

L. Pump Oil Drain Plug

Pump Speciﬁ cations

K PUMP

Inline, vertical twin cylinder

Single Stage

Oil Lubricated

Cast Iron crankcase cylinder, and head

Bore: 2-1/2" (63.5 mm)

Stroke: 2" (50.8 mm)

Weight: 47 lbs. ( 21.32 kg.)

Oil Capacity: 14 oz. (414 mL)

Pump Speciﬁ cations

G PUMP

V - twin 4 cylinder

Single Stage

Oil Lubricated

Cast Iron crankcase cylinder, and head

Bore: 2-1/2" (63.5 mm)

Stroke: 2-3/8" (60.33 mm)

Weight: 69 lbs. (31.3 kg.)

Oil Capacity: 30 oz. (887 mL)

Engine Speciﬁ cations

5.5 HP HONDA GX160

Internal Combustion

4-stroke

3450 RPM

9 HP HONDA HONDA GX270

Internal Combustion

4-stroke

3450 RPM

K

L

K

3

English

A

B

K

F

H

I

J

A

B

D

F

J

A

B

E

F

H

J

D55270, D55270T*

*Denotes 2-wheeled version

L

K

L

H

C

D

I

E

F

H

J

D

H

B

A

C

K

G

D55271, D55271T*

D55276

D55275

K

L

G

F

E

D

4

English

Hot Surfaces

Speciﬁ cations

MODEL D55270 D55271 D55275 D55276

WEIGHT

160 lbs. (72.57 kg) 213 lbs. (96.62 kg) 238 lbs. (107.96 kg) 185 lbs. (83.91 kg)

HEIGHT

25" (635 mm) 27.75" (704.85 mm) 33.75" (857.25 mm) 31" (787.4 mm)

WIDTH

18.25" (463.55 mm) 18.25" (463.55 mm) 20.25" (514.35 mm) 20.25" (514.35 mm)

LENGTH

43" (1092.2 mm) 43" (1092.2 mm) 43" (1092.2 mm) 43" (1092.2 mm)

AIR TANK CAPACITY (GALLONS)

8 (30.3 liters) 8 (30.3 liters) 17 (64.4 liters) 17 (64.4 liters)

APPROX. BLOW OFF PRESSURE

125 PSI (1034.2 kPa) 125 PSI (1034.2 kPa) 125 PSI (1034.2 kPa) 125 PSI (1034.2 kPa)

SCFM @ 100 PSI (275.8 kPa)

8.9 16.2 16.2 8.9

PUMP

K Pump G Pump G Pump K Pump

ENGINE

5.5 HP

HONDA GX160

9 HP

HONDA GX270

9 HP

HONDA GX270

5.5 HP

HONDA GX160

COMPRESSOR

CYLINDER &

HEAD

OUTLET TUBE

PUMP

CRANKCASE

ENGINE

MUFFLER

COMPRESSOR

CYLINDER & HEAD

PUMP

CRANKCASE

GASOLINE

ENGINE

MUFFLER

OUTLET TUBE

GASOLINE

ENGINE

5

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

E

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

EWALT (1-800-433-9258)

Important Safety Instructions

WARNING: Do not operate this unit until you read and understand

this instruction manual and the engine instruction manual for safety,

operation and maintenance instructions.

WARNING: This product may not be equipped with a spark-

arresting muffler. If the product is not equipped and will be used

around flam ma ble ma teri als or on land covered with materials such

as agricultural crops, forest, brush, grass or other similar items, then

an ap proved spark arrester must be installed and is legally required

in the state of California. It is a violation of California statutes

section 130050 and/or sec tions 4442 and 4443 of the California

Public Re sourc es Code, unless the engine is equipped with a spark

arrester, as defined in section 4442, and maintained in ef fec tive

work ing order. Spark arresters are also required on some U.S.

For est Service land and may also be legally required under other

statutes and or di nanc es.

WARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTION

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spilled gas o line and it’s

vapors can be come ignited

from cigarette sparks, electri-

cal arcing, exhaust gas es

and hot engine components

such as the muffler.

• Shut off en gine and allow it to

cool before adding fuel to the

tank.

• Use care in fill ing tank to avoid

spill ing fuel. Move unit away

from fueling area before start-

ing en gine.

• Heat will ex pand fuel in the

tank which could result in

spillage and pos si ble fire

explosion.

• Keep maximum fuel level

1/2" (12.7 mm) be low

bottom of filler neck

to allow for expansion.

6

English

• Combustible materials

which come into contact

with hot engine parts can

become ignited.

• Add fuel outdoors in a well

ventilated area. Make sure

there are no sources of igni-

tion, such as cigarettes near

refueling location.

• Operate compressor in

a clean, dry, well venti-

lated area a minimum of 48"

(1.22 meters) from any build-

ing, object or wall. Do not

operate unit indoors or in any

confined area.

• Operate compressor in an

open area away from dry

brush, weeds or other com-

bustible materials.

• Improperly stored fuel could

lead to acciden tal ignition.

Fuel im prop er ly secured

could get into the hands of

children or oth er un qual i fied

persons.

• Store fuel in an OSHA-

ap proved con tain er, in a

se cure location away from

work area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce the

risk of fire, do not allow

the compressor to operate

unattended.

• Always remain in attendance

with the product when it is

operating.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Breathing ex haust fumes

will cause se ri ous injury

or death! En gine exhaust con-

tains carbon mon ox ide, an

odorless and deadly gas.

• Always operate air compressor

outside in a clean, well

ventilated area. Avoid enclosed

areas such as garages,

basements, storage sheds,

which lack a steady exchange

or air. Keep children, pets

and others away from area of

operation.

• The compressed air directly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminant's can cause

serious injury or death.

• Air obtained directly from the

compressor should never be

used to supply air for human

consumption. In order to use air

produced by this compressor

for breathing, suitable filters and

in-line safety equipment must

be properly installed. In-line

filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior to

human consumption.

7

English

• Sprayed materials such as

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or safety

data sheets for the materials

you are spraying. Always use

certified safety equipment:

NIOSH/OSHA respiratory

protection designed for use with

your specific application.

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Oil can leak or spill and could

result in fire or breathing

hazard; serious injury or

death can result. Oil leaks will

damage carpet, paint or other

surfaces in vehicles or trailers.

• Always place compressor

on a protective mat when

transporting to protect against

damage to vehicle from leaks.

Remove compressor from

vehicle immediately upon arrival

at your destination. Always keep

compressor level and never lie

on its side.

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed and may be

UM coded (for units with air tanks greater than 6 inch diameter) accord-

ing to ASME Section VIII, Div. 1 rules. All pressure vessels should be

inspected once every two years. To find your state pressure vessels

inspector, look under the Division of Labor and Industries in the govern-

ment section of a phone book or call 1-800-4-D

EWALT for assistance.

The following conditions could lead to a weakening of the air tank, and

result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drain air tank daily or after each

use. If air tank develops a leak,

replace it immediately with a

new air tank or replace the

entire compressor.

• Modifications or attempted

repairs to the air tank.

• Never drill into, weld, or make

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorized modifications

to the unloader valve,

safety valve, or any other

components which control air

tank pressure.

• The air tank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

8

English

• FOR K PUMP UNITS

Excessive vibration can

weaken the air tank and

cause rupture or explosion.

Excessive vibration will

occur if the compressor is

not properly mounted or

if engine operates above

recommended RPM.

• Do not remove the stiffener bar

connecting the compressor

pump to the engine, except

to adjust belt tension, Then

securely tighten the stiffener

bar bolts. This bar controls unit

vibration.

Attachments & accessories:

• Exceeding the pressure rating

of air tools, spray guns, air

operated accessories, tires,

and other inflatables can

cause them to explode or

fly apart, and could result in

serious injury.

• Follow the equipment

manufacturers recommendation

and never exceed the maximum

allowable pressure rating

of attachments. Never use

compressor to inflate small

low pressure objects such

as children’s toys, footballs,

basketballs, etc.

Tires:

• Over inflation of tires could

result in serious injury and

property damage.

• Use a tire pressure gauge to

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE: Air tanks, compressors and

similar equipment used to inflate

tires can fill small tires similar to

these very rapidly. Adjust pressure

regulator on air supply to no more

than the rating of the tire pressure.

Add air in small increments and

frequently use the tire gauge to

prevent over inflation.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream

can cause soft tissue damage

to exposed skin and can

propel dirt, chips, loose

particles, and small objects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

• Always turn the compressor off

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

9

English

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal such

as the compressor head,

engine head, engine exhaust

or outlet tubes, can result in

serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The engine can start

accidentally if the flywheel is

turned by hand or moved by

pulling on the starter rope.

• Always disconnect the spark

plug and bleed pressure from

the air tank before performing

maintenance.

• Moving parts such as the

pulley, flywheel, and belt can

cause serious injury if they

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which are

damaged or removed.

• Keep your hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long

hair can be caught in moving

parts.

• Air vents may cover moving

parts and should be avoided as

well.

• Attempting to operate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in serious

injury.

• Any repairs required on this

product should be performed

by a D

EWALT factory service

center or a D

EWALT authorized

service center.

10

English

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your air

compressor could lead to se ri-

ous in ju ry or death to you or

others.

• Review and understand all

instructions and warnings in this

manual.

• Be come fa mil iar with the op er-

a tion and con trols of the air

compressor.

• Keep operating area clear of all

persons, pets, and obstacles.

• Keep chil dren away from the air

compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea tures

of this prod uct.

• Equip area of operation with a

fire extinguisher.

• Do not op er ate machine with

missing, broken, or un au tho-

rized parts.

• Never stand on the compressor.

WARNING: RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Serious injury can result from

attempting to lift too heavy

an object.

• The compressor is too heavy

to be lifted by one person.

Obtain assistance from others

before lifting.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute to

hearing loss.

• Always wear certified safety

equipment: ANSI S12.6

(S3.19) hearing protection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FEATURES

UNLOADER VALVE

When the maximum air tank pressure is obtained, the unloader

valve (H) will blow-off. This will cause the compressor to exhaust

the air to the atmosphere and not the tank.

Manual Lock: The manual lock allows you to manually unload the

compressor with air pressure in the air tank. To operate the manual

lock:

11

English

Rotate the manual lock unloaderlever to the

OPEN

H

CLOSED

H

open position to prevent air tank pressure

buildup. Rotate manual lock unloader lever to

the closed position after starting the engine

to allow air tank pressure to build. NOTE: Air

will not build in tank when manual lock

unloader lever in the open position.

SAFETY VALVE

This valve (I) is designed to prevent system failures

I

by relieving pressure from the system when the

compressed air reaches a predeter mined level. The

valve is preset by the manu facturer and must not be

removed or modified in any way.

AIR INTAKE FILTER

The filter (A) is designed to clean air entering the pump.

A

To ensure the pump continually receives a clean, cool,

and dry air supply the filter must always be clean and

the filter intake must be free from obstructions.

AIR TANK DRAIN VALVE

The drain valve (J) is used to remove

J

moisture from the air tank after the air

compressor is shut off.

AIR TANK PRESSURE GAUGE

The air tank pressure gauge (D) indicates air

F

E

D

pressure in the air tank.

REGULATED PRESSURE GAUGE

The regulated pressure gauge (E) indicates

the air pressure available at the outlet side of

the regulator. This pressure is controlled by the

regulator and is always less or equal to the air

tank pressure.

REGULATOR

The regulator knob (F) controls the air pressure coming from the air

tank.

To Adjust Regulator:

1. Pull regulator knob (F) out.

2. Turn knob clockwise to increase regulated pressure and

counterclockwise to decrease regulated pressure.

3. When desired pressure is shown on the regulated pressure

gauge push knob in to lock.

THROTTLE CONTROL

When maxi mum air tank pres sure is reached and the unloader

valve vents air, it activates the throttle control on the engine. This

gas saving feature holds the engine at a factory-set idling speed

until air pressure in the air tank drops to reset pressure. The

unloader valve then reactivates the throttle control and accelerates

the engine to full throttle.

LOW OIL SHUT DOWN SENSORS

The air compressor engine is equipped with a low oil shutdown

sensor. This is a safety device designed to protect your engine

from damage in the event the oil level in the crankcase is below

minimum.

If the oil in the engine gets low while the air compressor is running

it will automatically shut down the engine and will not restart until oil

is added to the engine or pump. If the oil is low before start-up, the

engine will not start until oil is added.

NOTE: The low oil shutdown sensor is very sensitive. You must fill

the engine and pump to the full mark on the dipstick to inactivate

this safety device.

12

English

INSTALLATION

Assembly (Fig. 1)

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Apply sealant tape to hose threads.

3. Assemble hose to air outlet (G). IMPORTANT: Do not assemble

splitters directly to the air outlet (G).

NOTE: Assembling quick connect bodies to air outlet (G) and quick

connect plugs to hose ends make connecting and disconnecting

hoses simple and easy. Quick connect bodies and plugs are

available for purchase from your local dealer or authorized service

center.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Remove hose(s) from air outlet(s) (G).

Lubrication and Oil

ENGINE

1. The engine was filled WITH oil at the manufacturer. Check engine

oil level before operating unit. If necessary, fill engine to the

appropriate level with recommended oil, see engine's instruction

manual supplied by engine manufacturer for correct procedure.

2. Add fuel to engine. See engine's instruction manual supplied by

engine manufacturer for correct procedure.

WARNING: Risk of explosion or fire. Gasoline vapor is highly

flammable. Refuel outdoors preferably, or only in well-ventilated

areas. Do not refuel or check gasoline level while the engine is

running. Do not store, spill, or use gasoline near an open flame,

a source of sparks (such as welding), or near operating electrical

equipment.

AIR COMPRESSOR

The air compressor pump was filled WITH oil at the manufacturer.

Check air compressor pump oil level before operating unit. See

Compressor Pump Oil under Maintenance.

Compatibility

Air tools and accessories that are run off the compressor must be

compatible with petroleum based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.

Location

WARNING: Risk of breathing. Exhaust from the gasoline engine

contains deadly carbon monoxide, which is odorless and toxic.

Operate engine only in well ventilated areas.

CAUTION: Risk of property damage. In order to avoid damaging

the air compressor, do not allow the unit to be tilted more than 10º

when operating.

Place air compressor at least 4 feet (1.2 m) away from obstacles that

may prevent proper ventilation. Keep unit away from areas that have

dirt, vapor and volatile fumes in the atmosphere which may clog and

gum up the intake filter and valves, causing inefficient operation.

13

English

HUMID AREAS

In frequently humid areas, moisture may form in the pump and

produce sludge in the oil, causing running parts to wear out

prematurely. Excessive moisture is especially likely to occur if the unit

is located in an unheated area that is subject to large temperature

changes. Two signs of excessive humidity are external condensation

on the pump when it cools down and a “milky” appearance in

compressor oil. You may be able to prevent moisture from forming in

the pump by increasing ventilation or operating for longer intervals.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable noise

levels in your area. To reduce excessive noise, use vibration mounts

or silencers, relocate the unit or construct total enclosures or baffle

walls. Contact a D

E

WALT service center or call 1-800-4-D

E

WALT for

assistance.

TRANSPORTING

WARNING: Risk injury from lifting. Unit weighs more than 160 lbs.

(72.6 kg) Do not move or lift without assistance.

CAUTION: Risk of property damage. The wheels and handle do

not provide adequate clearance, stability or support for pulling the

unit up and down stairs or steps. The unit must be lifted, or pushed

up a ramp.

When transporting the com-

M, N

O

M, N

M

pressor in a vehicle, trailer,

etc. ensure that the air tank is

drained and the unit is secured

and placed on a flat horizontal

surface. NOTE: Use

recommended tie down points

(M) when transporting. Use

care when driving so to avoid tipping the unit over in the vehicle.

Damage can occur to the unit

M, N

O

M

or surrounding items if unit is

tipped. Use a ramp if loading

or unloading the unit from a

height of more than 12"

(304.8 mm).

LIFTING

Always use two people when

lifting and lift from the recommended lift points (N).

WARNING: Risk injury from lifting. Unit weighs more than 160 lbs.

(72.6 kg) Do not move or lift without assistance.

MOVING

1. Grasp handle (O) of compressor, and lift compressor high

enough so unit can be rolled on the front tire(s).

WARNING: Risk of unsafe operation. Ensure proper footing and

use caution when rolling compressor so that unit does not tip or

cause loss of balance.

2. When location is reached slowly lower rear of compressor to

ground. Always store compressor in a horizontal position.

NOTE: Should the unit tip over, hard starting and smoking will occur

due to oil spillage.

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

3. Ensure the drain valve (J) is closed.

4. Ensure safety valve (I) is functioning properly, see Checking

Safety Valve under Maintenance.

14

English

5. Check pump oil level, see Compressor Pump Oil under

Maintenance.

CAUTION:

Do not operate without oil or with inadequate oil.

D

EWALT is not responsible for compressor failure caused by

inadequate oil.

6. Check engine's oil and fuel level, see engine's instruction manual

for correct procedures.

7. Visually inspect drive belt. Replace belt if frayed, cracked, or worn.

NOTE: Outer belt cover must be removed to inspect drive belt.

8. Ensure all guards, covers, and labels are in place, legible (for

labels) and securely mounted. Do not use compressor until all

items have been verified.

Initial Set-up

(Fig. 1)

WARNING: Do not operate this unit until you read and understand

this instruction manual and the engine instruction manual for safety,

operation and maintenance instructions.

BREAK-IN PROCEDURE

WARNING: Risk of property damage. Serious damage may result

if the following break-in instructions are not closely followed.

This procedure is required:

• Before the air compressor is used for the first time.

• When the unloader valve has been replaced.

• When the compressor pump has been replaced.

The procedure:

1. Follow Pre-Start Checklist under Preparation for Use.

2. Rotate the unloader's manual lock to the open position to

prevent air tank pressure buildup.

3. Open the pressure regulator. Pull regulator knob (F) out and

rotate clockwise until it stops.

WARNING: Do not operate this unit until you read and understand

the engine instruction's manual for safety, operation and maintenance

instructions.

4. Prepare engine for first time use, see engine's instruction manual

for correct procedure.

5. Turn the engine ON/OFF switch (C) to the ON position.

6. Start engine, see engine's instruction manual for correct

procedure.

7. Run the air compressor for 30 minutes to seat the rings and

lubricate all the internal surfaces. Ensure there is no pressure

build up in the air tank by observing the reading on the air tank

pressure gauge.

8. Rotate the manual lock on the unloader valve into the closed

position so the air tank pressure can build.

9. Close the pressure regulator. Rotate the regulator knob (F)

counterclockwise to its built-in stop and push knob in to lock in

place. This will allow air to build pressure in the air tank.

10. Compressed air will be available from the hose air outlet until it is

used up or bled off.

OPERATING PROCEDURES

Start-up (Fig. 1)

1. Follow Pre-Start Checklist under Preparation for Use.

2. Pull out and turn regulator knob (F) counterclockwise until fully

closed. Push in to lock. Regulated pressure gauge should read

0 PSI (0 kPa).

3. Rotate the manual lock unloader lever to the open position to

assist with start up.

4. Turn the engine ON/OFF switch (C) to the ON position.

5. Start engine, see engine's instruction manual for correct

procedure.

15

English

6. Rotate manual lock unloader lever to the closed position to allow

air tank pressure to build. NOTE: Pump will not operate with the

manual lock unloader lever in the open position.

7. Allow compressor to pump up to blow off pressure.

NOTE: If any unusual noise or vibration is noticed, stop the compressor

and refer to the troubleshooting section.

NOTE: The air compressor pump is capable of running continuously.

To prolong the air compressor's life, it is recommended to run at high

throttle 50-75% of the run time and idle for 25% of the run time

8. Attach hose and accessory.

CAUTION: Risk of unsafe operation. Compressed air from the unit

may contain wa ter condensation and oil mist. Do not spray un fil tered

air at an item that could be damaged by moisture. Some air op er ated

tools or de vic es may require filtered air. Read the in struc tions for the

air tool or device.

9. Adjust regulator (F) to desired setting. See Regulator under

Features.

Shut-down

1. Stop engine, see engine's instruction manual for correct

procedure.

NOTE: If finished using compressor, follow Steps 2–6.

2. Turn regulator knob (F) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 PSI (0 kPa).

3. Remove hose and accessory.

4. Drain the air tank.

See Draining Air Tank under Maintenance

.

WARNING: Risk of bursting. Drain air tank daily. Water will condense

in air tank. If not drained, water will corrode and weaken the air tank

causing a risk of air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non freezing area.

MAINTENANCE

The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Disconnect spark plug wire.

3. Drain air tank.

4. Allow air compressor to cool down before starting service

NOTE: All compressed air systems contain maintenance parts (e.g.

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should

be performed by a D

EWALT factory service center or a DEWALT

authorized service center.

Maintenance Chart

Procedure Daily Weekly Monthly 1 year or

200 Hours

Check safety valve

X

Inspect air filter

+

X

Drain air tank

X

Check pump oil level

X

Change pump oil**

+

X

Oil leak inspection

X

Inspect drive belt

X

Check drive belt tension

X

16

English

Procedure Daily Weekly Monthly 1 year or

200 Hours

Check pulley/flywheel

alignment

X

Check for unusual noise/

vibration

X

Check for air leaks*

X

Clean compressor exterior

X

Engine See engine instruction manual.

* To check for air leaks apply a solution of soapy water around joints.

While compressor is pumping to pressure and after pressure cuts out,

look for air bubbles to form.

** The pump oil must be changed after the first 20 hours or operation.

Thereafter, when using

DEWALT

synthetic compressor oil, change oil

every 200 hours of operation or once a year, whichever comes first.

+ Perform more frequent in dusty or humid conditions.

Checking Safety Valve (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is stuck

or does not operate smoothly, it must be replaced with the same

type of valve.

Checking Air Filter Element (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Allow unit to cool.

3. Remove filter (A) top from filter base by turning filter counter-

clockwise about 5 degrees.

4. Separate filter top from base.

5. Remove element from filter base.

6. If element needs cleaning, blow out with air. Replace if needed.

Purchase replacement parts from your local dealer or authorized

service center. Always use identical replacement parts.

7. Place element back in filter base.

8. Reconnect filter top to filter base. While pushing in, rotate clock-

wise 5 degrees.

CAUTION: Risk of unsafe operation. Do not operate without air

inlet filter.

Draining Air Tank (Fig. 1)

WARNING: Risk of unsafe operation. Risk from noise. Air tanks

contain high pressure air. Keep face and other body parts away from

outlet of drain. Use safety glasses when draining as debris can be

kicked up into face. Use ear protection (

ANSI S12.6 (S3.19) hearing

protection)

as air flow noise is loud when draining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g., tanks, filter, aftercoolers,

dryers). This condensate contains lubricating oil and/or substances

which may be regulated and must be disposed of in accordance with

local, state, and federal laws and regulations.

17

English

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Place a suitable container under the drain valve to catch

discharge.

3. Grasp black lever on drain valve.

4. Slowly rotate lever to gradually bleed air from air tank.

5. When air tank pressure gauge reads 10 PSI (68.9 kPa), rotate

valve to the fully open position.

6. Close drain valve when finished.

Compressor Pump Oil (Fig. 1)

CHECKING OIL

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

CAUTION: Risk of Unsafe Operation. Overfilling with oil will cause

premature compressor failure. Do not overfill.

NOTE: When filling the crankcase, the oil flows very slowly into the

pump. If the oil is added too quickly, it will overflow and appear to

be full.

1. Ensure engine ON/OFF switch (C) is in the OFF Position.

2. Place unit on a flat level surface.

3. FOR K PUMP UNITS

• Remove dipstick (K) and wipe clean.

• Insert and remove dipstick without

MAX.

OIL

MIN.

threading dipstick into crankcase as

shown in figure.

• Check the oil level on dipstick.

If oil level is at or below “Add”,

oil needs to be added. Add D

EWALT

synthetic oil to the proper maximum

level as shown in figure.

FOR G PUMP UNITS

• Remove oil fill plug (K).

• Check the oil level. Oil should not

MAX.

OIL

MIN.

exceed top raised line on side of

crackcase. (Oil will be even with

bottom of threads in crankcase fill

port), if needed add D

EWALT

synthetic oil to the proper level.

4. Replace dipstick/oil fill plug and tighten

securely.

CHANGING OIL

NOTE: Pump oil contains substances that are regulated and must

be disposed of in accordance with local, state and federal laws and

regulations.

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Allow the unit to cool.

3. Disconnect spark plug wire.

4. Drain air tank.

5. Locate a suitable container under pump drain plug (J).

6. Remove the dipstick/oil fill plug (K) from crank case.

7. Remove the oil drain plug (L).

8. Allow ample time for all oil to drain out. (Tilting the compressor

towards the drain plug will assist in draining.)

9. Install the oil drain plug.

10. Fill pump with D

EWALT synthetic compressor oil.

18

English

FOR K PUMP UNITS

The oil level should be at “Add” on the dipstick.

FOR G PUMP UNITS

Oil should not exceed top raised line on side of crackcase. (Oil

will be even with bottom of threads in crankcase fill port.)

11. Replace dipstick/oil fill plug and tighten securely.

12. Reconnect spark plug wire.

Checking Belt Tension (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Allow the unit to cool.

3. Disconnect spark plug wire.

4. Drain air tank.

5. FOR K PUMP UNITS

Remove six belt guard mounting screws (two on the pump head

and four on the deck)

FOR G PUMP UNITS

Remove seven belt guard mounting screws and J-hook (two on

the pump head and four on the deck).

6. Remove outer belt cover.

7. Measure belt tension. Proper tension is achieved when a three

(3) pound weight or equivalent finger pressure applied midway

between the motor pulley and compressor flywheel causes a

1/4" (6.35 mm) deflection of the belt. If adjustment is needed see

Adjusting Belt Tension under Maintenance.

8. Replace belt guard.

9. Reconnect spark plug wire.

Adjusting Belt Tension

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

1. Follow procedures 1-6 in Checking Belt Tension under

Maintenance.

NOTE: The engine or pump will be mounted in the slotted holes on

the deck, determine this before continuing.

2. Scribe a mark at the base of the pump or engine (whichever

is mounted in the slotted holes) on the deck to be used as a

reference.

3. Loosen four pump or engine (whichever is mounted in the slot-

ted holes) mounting nuts .

4. FOR K PUMP UNITS ONLY

Loosen but do not remove pump stiffener bracket bolt.

5. Remove the belt.

6. Scribe a mark approximately 1/8" (3.2 mm) from the original

mark.

7. Slide the pump or engine to the new mark and retighten the

pump or engine mounting nuts.

WARNING: Risk of moving parts. Use caution when rolling

belt onto flywheel, fingers can get caught between the belt and

flywheel.

8. With the pump or engine secure, roll the belt over the flywheel

and the pulley.

9. Check the belt tension again. See Step 7 in Checking Belt

Tension under Maintenance.

10. When tension is correct, torque four pump or engine mounting

nuts (pump torque to 6–8 ft.- lbs./8.1–10.8 Nm, engine torque

to 8– 10 ft.-lbs. (10.8–13.6 Nm), stiffener bracket bolt (Torque to

10–12 ft.- lbs./13.5–16.3 Nm), and replace belt cover.

19

English

11. Reconnect spark plug wire.

Pulley and Fly wheel Alignment

The air compressor flywheel and engine pulley must be in-line (in

the same plane) within 1/16" (1.6 mm) to ensure belt retention within

flywheel belt grooves. To check alignment:

1. Ensure engine ON/OFF switch (C) is in the OFF Position.

2. Allow the unit to cool.

3. Disconnect spark plug wire.

4. Drain air tank.

5. Remove outer belt cover.

6. Place a straightedge

S

Q

R

A1

A2

A2 B1 B2

B1 B2

T

(Q) against the outside

of the flywheel (R) and

the engine drive pulley

(S).

7. Measure the distance

between the edge of the

belt (T) and the straightedge at points A1 and A2 in Figure. The

difference between mea sure ments should be no more than

1/16" (1.6 mm).

8. If the difference is greater than 1/16" (1.6 mm), loosen the

setscrew holding the engine drive pulley to the shaft and adjust

the pulley's position on the shaft until the A1 and A2 mea sure-

ments are within 1/16" (1.6 mm) of each other.

9. Tighten the engine drive pulley setscrew. Torque to 145–165 in.-lbs.

(16.4– 18.6 Nm).

10. Visually inspect the engine drive pulley to verify that it is

perpendicular to the drive motor shaft. Points B1 and B2 of Figure

should appear to be equal. If they are not, loos en the setscrew of

the engine drive pulley and equal ize B1 and B2, using care not to

disturb the belt align ment per formed in Step 8.

11. Retighten the engine drive pulley set screw. Torque to

145– 165 in.-lbs. (16.4–18.6 Nm).

12. Reinstall belt guard.

13. Reconnect spark plug wire.

ACCESSORIES

Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center.

If you need assistance in locating any accessory for your tool,

please contact D

E

WALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

EWALT (1-800-433-9258) or

visit our website www.dewalt.com.

CAUTION: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number ___________

Date and Place of Purchase ____________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

E

WALT factory service

center, a D

E

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

20

English

Full One Year Warranty

DEWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

E

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

E

WALT for a free

replacement.

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

kPa (kilopascal): Metric pressure measurement. 1 kilopascal

equal 1000 pascals.

Code Certification: Products that bear one or more of the

following marks: UL, CUL, ETL, CETL, have been evaluated

by OSHA certified independent safety laboratories and

meet the applicable Underwriters Laboratories Standards

for Safety.

California Code: Unit may comply with California Code 462 (l)

(2)/(M) (2). Specification/model label is on the side of the

air tank on units that comply with California Code.

Unloader Blow-Off Pressure: All models are continuous

running units controlled by air tank pressure. When the

maximum air tank pressure is obtained, the unloader

valve will blow-off. This will cause the compressor to

exhaust the air to the atmosphere and not the tank. This

decreases the load on the engine and allows it to run at

a near no-load condition.

Unloader Reset Pressure: When the air tank pressure drops

to a predetermined point, the unloader valve closes. The

air tank pressure will now increase until it reaches the

unloader blow-off pressure.

La page charge ...

DeWalt D55270 Manuel utilisateur

Ce manuel convient également à

DeWalt D55270 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents