Allen Bradley Allen-Bradley 1794-IB10XOB6 FLEX I/O Digital Input/Output Module Manuel utilisateur

Marque: Allen Bradley

Modèle: Allen-Bradley 1794-IB10XOB6 FLEX I/O Digital Input/Output Module

Taper: Manuel utilisateur

Installation Instructions

Original Instructions

FLEX I/O Digital Input and Output Modules

Catalog Numbers 1794-IB10XOB6, 1794-IB16XOB16P

Summary of Changes

This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.

Topic Page

Summary of Changes 1

Overview 5

Install Your Digital Input/Output Module 5

Configure Your Module 8

Specifications 9

Topic Page

Updated template throughout

Updated UK and European Hazardous Location Approval 4

Updated Special Conditions for Safe Use 4

Updated IEC Hazardous Location Approval 4

Updated General Specifications 10

Updated Environmental Specifications 10

Updated Certifications 11

2Rockwell Automation Publication 1794-IN083E-EN-P - July 2022

FLEX I/O Digital Input and Output Modules Installation Instructions

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain

this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of

practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

󴎥󲼒󽴼󱲉󲔞󷠴󸞂󶔩󳕽󰽳󱠥󶑷󳇢󳦦󰹢󱡸󱑹󼵼󷸽󸾔󷹁󳦦󳛓󳮔󰻅󱛻 󽶴 󱌧󰺮󸀵󴙃 󽶵 󸛉󱐕󱐪󱐁󵒹󳥤󱌣󷸄󱾋󲔞󷠴󸞂󶔩󱠥󳕽󰽳󵒹󵕲󲪿󳛓󳮔󹀒󰸬󳄿󳥤󸓔󵈾󷨟󶲵󴎂󲲓󱠥󳫼󱎦󵒹

󵕲󱌣󷦴󴊡󰷔󱾫󼵼󵈾󳄫󸑯󲳴󹏣󴰀󲸫󲔞󷠴󱠥󳍺󶑂󷸺󳟉

󲔞󷠴󷹉󳚯󳇐󸑙󰾫󵈾󶑇󷠴󳈓󱙹󱠥󶑷󳇢󵴞󱝑󹏡󳕽󰽳󲳴󹏣󵉌󶑒󸑃󸓔󲰳󷷳󶑆󵒹󰶂󰶍󰺄󱟘󳉾󴮒󸓔󵈾󵒹󳕽󰽳󷨟󶲵󲕋󳜷

󲁶󳩔󳦣󳉾󴮒󱑗󸔤󱥂󳉸󲕂󵒹󳜱󲮮󰾫󵈾󷸫󷸄󱾋󼵼󱐮󱜴󶡋󰼕󳌁󲕳󷸄󱾋󳏀󰿙󵒹󱁃󳇢

ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos adicionales acerca de la

instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos los códigos, leyes y estándares vigentes.

El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el código de

práctica aplicable. Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.

ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou manter este produto. Os

usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.

É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e especializado, de acordo com o

código de prática aplicável.

Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.

ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и документы,

перечисленные в разделе «Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации данного оборудования.

Пользователи обязаны ознакомиться с инструкциями по установке и прокладке соединений, а также с требованиями всех применимых норм, законов и

стандартов.

Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться

обученным персоналом в соответствии с применимыми нормами и правилами.

Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.

󴎤󲼑 : 󳦥󷢢󱡸󷫤󶔨󳸔󳃮󵫪󱕜󱁃󲔛󱑹󳦥󳥆󳦥󳼤󱬼󷫤󶔨󷫤󲕁󳕽󰽳󱛬󶙌󷽺󳛲󷭪󲰳󵶙󳄾󷪹󸋺󳛒󳥆󵕢󸔑

󷭪󲰳󳧵󰾾󴎁󲲓󷧊󳭔󷦳󰻞󱔈󷫤󶔨󸞂󶊁󳅜󹌬󶗠󴯿󲳴󷦳

󷫤󶔨󷰄󳚮󸖋󸋅󸻛󲄤󰾫󵈾󶅉󵰨󷩒󰽥󱁃󲔛󱞎󷲀󰽳󳵠󷭪󲰳󲕌󳜶󷧊󱑲󲲟󷪯󶊻󱜍󸗞󱐗󰽳󳵠󱢟󲕌󷝥󲳴󷦳

󳦥󳼤󱬼󷢢󸔢󳉸󲕁󳜰󴎁󰾫󵈾󱸦󱝖󳼤󱬼󳏀󰿙󱁃󷶋󳐧󲷋

ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten, bevor Sie

dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zusätzlich mit den Installations- und

Verdrahtungsanweisungen vertraut machen.

Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in Übereinstimmung mit den

anwendbaren Ausführungsvorschriften vorgenommen werden.

Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.

ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant d’installer, configurer,

utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois et normes en vigueur.

Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de pratique en vigueur.

Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.

󻷋󻰧 : 󻇇󽴔󻳫󼥗󽴔󻗳󼌧 , 󻗳󻳤 , 󻱠󺢨󽴔󺫟󺝣󽴔󻯯󻺏󽴔󻇃󻛧󼨧󺋿󽴔󻳓󻪟󽴔󻇇󽴔󻀇󻗫󺹋󽴔󼢻󼨷󼨧󻪻󽴔󻗳󼌧 , 󻗳󻳤󽴔󻃞󽴔󻱠󺢨󻪟󽴔󺇏󼨫󽴔󼄇󺆯󽴔󻱟󺶛󽴔󻘈󻘧󻰧󽴔󻀇󻗫󺦳󻰓󽴔󻃧󺦫󻞫󽴔󻱌󺆯󽴔󻛨󻺏󼨧󻞼󻞫󻫳 . 󻕻󻭸󻱟󺝣󽴔󺽷󺦯󽴔󺇏󺳷󽴔󺊫󻳤 ,

󻅤󺊫󽴔󻃞󽴔󼤫󻷏󻪟󻗫󽴔󻭣󺈻󼨧󺝣󽴔󻕻󼨼󻪟󽴔󺟏󼩃󽴔󻃧󺦫󻞫󽴔󻗳󼌧󽴔󻃞󽴔󻃿󻗯󽴔󻺏󼌷󻰓󽴔󻛨󻺏󼩃󻩋󽴔󼨸󺞗󺞳 .

󻗳󼌧 , 󻴿󻳤 , 󺃏󺢨 , 󻕻󻭸 , 󻴿󺺌 , 󻉓󼩃 , 󻯯󻺏󻇃󻛧󽴔󺧀󽴔󺽷󺦯󽴔󻱠󻪔󻰏󽴔󺇏󺳷󽴔󺊫󻳤󻪟󽴔󺧿󺱋󽴔󻳐󻳗󼨫󽴔󺈟󻯰󻰓󽴔󻃪󻰏󽴔󻕻󻭸󻱟󺹋󽴔󼚄󼩃󻗫󺺛󽴔󻛧󼩘󼩃󻩋󽴔󼨸󺞗󺞳 .

󻇇󽴔󻱴󻌓󺹋󽴔󻳫󻴿󻕻󺃏󽴔󺽔󻞫󼨧󻺏󽴔󻨙󻰏󽴔󻃸󻅤󻰋󺴫󽴔󻕻󻭸󼨧󺽃󽴔󻱴󻌓󻰧󽴔󻇃󼬇󽴔󺋿󺝴󻱃󽴔󻙟󻖐󺣯󽴔󻛧󽴔󻱗󻞄󺞗󺞳 .

ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione “Altre risorse”,

riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti dalle leggi, codici e

standard applicabili.

Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.

Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.

DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer listelenmiş

dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.

Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçaları sökme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama yönetmeliklerine uygun şekilde

yapılabilir.

Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.

岤䠑✲갪㖈㸞酤鏤㹁乽⡲䧴笞隌劥欴ㅷ⵹锞⯓ꠗ隡姽俒⟝⟃⿻⴪倴 չⰦ➮须彂պ畎眏⚥剤ꡠ㸞酤鏤㹁莅乽⡲姽鏤⪔涸俒⟝⢪欽罏䗳갭擿䜫㸞酤ㄤꂂ箁䭸

爚⚛痘ざ䨾剤岁鋊岁䖒ㄤ垦彋銴宠

⺫䭍㸞酤锅侮❜➰⢪欽⢪欽穉酤䬓⽹ㄤ笞隌瘞⹛⡲鿪䗳갭❜歋䊺竤麕黠殹鎯箻涸➃㆞鹎遤⟃痘ざ黠欽涸㻜⡲岁鋊

㥶卓㼟鏤⪔欽倴ꬌ醢鸤㉂䭸㹁涸欽鸁儘〳腋剚鸤䧭鏤⪔䨾䲿⣘涸⥃隌⸆腋「䴦

POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně instalace, konfigurace

a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů anorem nutně seznámit také s pokyny pro instalaci a elektrické zapojení.

Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.

Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.

UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe źródła omawiające

instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania, jak również z obowiązującymi kodeksami,

prawem i normami.

Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel zgodnie z

obowiązującym kodeksem postępowania.

Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.

OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller börjar använda eller utföra

underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och standarder.

Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.

Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.

LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product installeert,

configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en normen.

Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en in

overeenstemming met de geldende praktijkregels.

Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.

Rockwell Automation Publication 1794-IN083E-EN-P - July 2022 3

FLEX I/O Digital Input and Output Modules Installation Instructions

Environment and Enclosure

Prevent Electrostatic Discharge

Special Conditions for Safe Use

Electrical Safety Considerations

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in EN/IEC

60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such

environments.

This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The enclosure

must have suitable flame-retardant properties to prevent or minimize the spread of flame, complying with a flame spread rating of 5V A or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only by the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures.

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration, and operation of this

equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions

in addition to requirements of all applicable codes, laws, and standards.

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in

accordance with applicable code of practice. In case of malfunction or damage, no attempts at repair should be made. The module should be returned to the

manufacturer for repair. Do not dismantle the module.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION:

• This product is grounded through the DIN rail to chassis ground. Use zinc plated chromate-passivated steel DIN rail to assure proper grounding. The use of

other DIN rail materials (for example, aluminum or plastic) that can corrode, oxidize, or are poor conductors, can result in improper or intermittent grounding.

Secure DIN rail to mounting surface approximately every 200 mm (7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail properly. Refer to

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more information.

• Do not remove or replace a terminal base unit while power is applied. Interruption of the backplane can result in unintentional operation or machine motion.

• Do not remove or replace an Adapter Module while power is applied. Interruption of the backplane can result in unintentional operation or machine motion.

• If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

WARNING:

• When you insert or remove the module while backplane power is on, an electric arc can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding. Repeated electric arcing causes excessive wear to contacts on both the module

and its mating connector. Worn contacts may create electrical resistance that can affect module operation.

• If you insert or remove the module while backplane power is on, an electric arc can occur. This could cause an explosion in hazardous location installations. Be

sure that power is removed or the area is nonhazardous before proceeding.

• When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method that complies with the

governing electrical codes.

WARNING: If you connect or disconnect wiring while the field-side power is on, an electrical arc can occur. This could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is nonhazardous before proceeding.

ATTENTION:

• This equipment is certified for use only within the surrounding air temperature range of -20…55 °C (-4…131 °F). The equipment must not be used outside of this

range.

• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.

4Rockwell Automation Publication 1794-IN083E-EN-P - July 2022

FLEX I/O Digital Input and Output Modules Installation Instructions

UK and European Hazardous Location Approval

The following module is European Zone 2 approved: 1794-IB10XOB6.

IEC Hazardous Location Approval

North American Hazardous Location Approval

The 1794-IB10XOB6 and 1794-IB16XOB16P modules are Hazardous Location approved:

The following applies to products marked II 3 G:

• Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such equipment

given in Schedule 1 of UKEX and Annex II of EU Directive 2014/34/EU. See the UKEx and EU Declaration of Conformity at rok.auto/certifications for details.

• The type of protection is Ex ec IIC T3 Gc according to EN IEC 60079-0:2018, EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS, Issue Date 07/2018 and

EN IEC 60079-7:2015+A1:2018, Explosive atmospheres. Equipment protection by increased safety "e".

• Comply to Standard EN IEC 60079-0:2018, EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS, Issue Date 07/2018, EN IEC 60079-7:2015+A1:2018

Explosive atmospheres. Equipment protection by increased safety "e", reference certificate number DEMKO 14 ATEX 1342501X and UL22UKEX2378X.

• Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and for short

periods. Such locations correspond to Zone 2 classification according to UKEX regulation 2016 No. 1107 and ATEX directive 2014/34/EU.

WARNING: Special Conditions for Safe Use

• This equipment is not resistant to sunlight or other sources of UV radiation.

• This equipment shall be mounted in an UKEX/ATEX/IECEx Zone 2 certified enclosure with a minimum ingress protection rating of at least IP54 (in accordance

with EN/IEC 60079-0) and used in an environment of not more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when applied in Zone 2 environments.

The enclosure must be accessible only by the use of a tool.

• This equipment shall be used within its specified ratings defined by Rockwell Automation.

• Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the equipment.

• This equipment must be used only with UKEX/ATEX/IECEx certified Rockwell Automation backplanes.

• Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this

product.

• Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.

• Earthing is accomplished through mounting of modules on rail.

The following applies to products marked with IECEx certification:

• Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and for short

periods. Such locations correspond to Zone 2 classification to IEC 60079-0.

• The type of protection is Ex ec IIC T3 Gc according to IEC 60079-0 and IEC 60079-7.

• Comply to Standards IEC 60079-0, Explosive atmospheres Part 0: Equipment - General requirements, Edition 7, Revision Date 2017, IEC 60079-7, 5.1 Edition revision date 2017,

Explosive atmospheres - Part 7: Equipment protection by increased safety "e", reference IECEx certificate number IECEx UL 14.0066X.

The following information applies when operating this equipment in

hazardous locations: Informations sur l'utilisation de cet équipement en environnements dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2

Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each

product is supplied with markings on the rating nameplate indicating the hazardous

location temperature code. When combining products within a system, the most

adverse temperature code (lowest "T" number) may be used to help determine the

overall temperature code of the system. Combinations of equipment in your system

are subject to investigation by the local Authority Having Jurisdiction at the time

of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à une utilisation en

environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque d'identification qui indiquent le

code de température pour les environnements dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de température le plus défavorable (code de

température le plus faible) peut être utilisé pour déterminer le code de température global

du système. Les combinaisons d'équipements dans le système sont sujettes à inspection

par les autorités locales qualifiées au moment de l'installation.

WARNING:

Explosion Hazard –

• Do not disconnect equipment unless power has been

removed or the area is known to be nonhazardous.

• Do not disconnect connections to this equipment unless

power has been removed or the area is known to be

nonhazardous. Secure any external connections that

mate to this equipment by using screws, sliding latches,

threaded connectors, or other means provided with this

product.

• Substitution of components may impair suitability for

Class I, Division 2.

AVERTISSEMENT:

Risque d’Explosion –

• Couper le courant ou s'assurer que l'environnement est classé

non dangereux avant de débrancher l'équipement.

• Couper le courant ou s'assurer que l'environnement est classé

non dangereux avant de débrancher les connecteurs. Fixer

tous les connecteurs externes reliés à cet équipement à l'aide

de vis, loquets coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

• La substitution de composants peut rendre cet équipement

inadapté à une utilisation en environnement de Classe I,

Division 2.

Rockwell Automation Publication 1794-IN083E-EN-P - July 2022 5

FLEX I/O Digital Input and Output Modules Installation Instructions

Overview

Install Your Digital Input/Output Module

The FLEX™ I/O 1794-IB10XOB6 module mounts on a 1794-TB3 or 1794-TB3S terminal base. The 1794-IB16XOB16P module mounts on a 1794-TB32 or 1794-TB32S terminal base.

1. Rotate the keyswitch (1) on the terminal base (2) clockwise to position 2 as required for this type of module.

2. Ensure that the Flexbus connector (3) is pushed all the way to the left to connect with the neighboring terminal base/adapter. You cannot install the module unless the

connector is fully extended.

3. Make sure the pins on the bottom of the module are straight so they will align properly with the connector in the terminal base.

4. Position the module (4) with its alignment bar (5) aligned with the groove (6) on the terminal base.

5. Press firmly and evenly to seat the module in the terminal base unit. The module is seated when the latching mechanism (7) is locked into the module.

Connect Wiring for the 1794-IB10XOB6

1. Connect individual input and output wiring to numbered terminals on the 0...15 row (A) as indicated in Table 1.

2. Connect the associated +V DC power lead of the input device to the corresponding terminal on the 34…51 row (C) for each input as indicated in Table 1. (The +V power

terminals of row (C) are internally connected together.)

3. Connect the associated input device common (3-wire devices only) and output device common to the corresponding terminals on the 16…33 row. (B) for each input and

output as indicated in Table 1. (Commons are internally connected together.)

4. Connect +V DC power to terminal 34 on the 34...51 row (C).

5. Connect V DC common to terminal 16 on the 16...33 row (B).

6. If daisychaining power to the next terminal base, connect a jumper from terminal 51 (+V DC) on this base unit to terminal 34 on the next base unit.

7. If continuing DC common to the next base unit, connect a jumper from terminal 33 (common) on this base unit to terminal 16 on the next base unit.

Description Description

1 Keyswitch 5 Alignment bar

2Terminal base 6Groove

3 Flexbus connector 7 Latching mechanism

4Module

ATTENTION: During mounting of all devices, be sure that all debris (metal chips, wire strands, etc.) is kept from falling into the module. Debris that falls into the

module could cause damage on power up.

Table 1 - Wiring Connections for 1794-IB10XOB6

Input(1) Signal Return Supply

Sink input

Input 0 A-0 B-17 C-35

Input 1 A-1 B-18 C-36

Input 2 A-2 B-19 C-37

Input 3 A-3 B-20 C-38

Input 4 A-4 B-21 C-39

Input 5 A-5 B-22 C-40

Input 6 A-6 B-23 C-41

Input 7 A-7 B-24 C-42

Input 8 A-8 B-25 C-43

6Rockwell Automation Publication 1794-IN083E-EN-P - July 2022

FLEX I/O Digital Input and Output Modules Installation Instructions

1794-TB3 and 1794-TB3S Terminal Base Wiring for 1794-IB10XOB6

2 and 3-Wire Input Wiring for 1794-IB10XOB6

Connect Wiring for the 1794-IB16XOB16P

1. Connect individual input wiring (IN0 to IN15) to numbered terminals on the 0...15 row (A) as indicated in Table 2 on page 7.

2. Connect the associated power to the +V1 terminal (35, 37, 39 or 41) on the 34...51 row (C) as indicated in Table 2 on page 7.

3. Connect the associated common (-V1) for IN0 to IN15 to COM1 (terminal 36, 38, 40 or 42) on the 34...51 row (C).

4. Connect individual output wiring (OUT0 to OUT15) to terminals 17 to 32 on the 16...33 row (B) as indicated in Table 2 on page 7. (Note: Do not connect to terminals 16 or 33.)

5. Connect the associated power to the +V2 terminal (43, 45, 47 or 49) on the 34...51 row (C) as indicated in Table 2 on page 7.

6. Connect the associated common (-V2) for OUT0 to OUT15 to COM2 (terminal 44, 46, 48 or 50) on the 34...51 row (C).

7. If continuing input wiring to the next terminal base unit, connect a jumper from terminal 41(+V1) to the power terminal on the next base unit; connect a jumper from terminal

42 (COM1) to the common terminal on the next base unit.

8. If continuing output wiring to the next terminal base unit, connect a jumper from terminal 49 (+V2) to the power terminal on the next base unit; connect a jumper from

terminal 50 (COM2) to the common terminal on the next base unit.

Input 9 A-9 B-26 C-44

Source output

Output 0 A-10 B-27 –

Output 1 A-11 B-28 –

Output 2 A-12 B-29 –

Output 3 A-13 B-30 –

Output 4 A-14 B-31 –

Output 5 A-15 B-32 –

+V DC C-34 to C-51 (internally connected together)

Common B-16 to B-33 (internally connected together)

(1) 2-wire input devices use signal and supply terminals; 3-wire devices use signal, return, and supply terminal

Table 1 - Wiring Connections for 1794-IB10XOB6 (Continued)

Input(1) Signal Return Supply

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

Inputs

Commons

(1794-TB3 shown)

-V (Supply Common) = Terminals B-16 and B-33

+V (Supply +Voltage In) = Terminals C-34 and C-51

-V

Voltage

In +V

Voltage

Out +V

Voltage

(Use B-33 and C-51 for daisy-chaining to next terminal base unit)

Common -V

Common

Outputs

0-15

16-33

34-51

= Sink Input

= Common

= +V DC

2-Wire Device

(Sourcing Output) 3-Wire Device

(Sourcing Output)

Rockwell Automation Publication 1794-IN083E-EN-P - July 2022 7

FLEX I/O Digital Input and Output Modules Installation Instructions

1794-TB32 Terminal Base Wiring for 1794-IB16XOB16P

Table 2 - Wiring Connections for 1794-IB16XOB16P

Input Signal Return Supply(1)

(1) 2-wire input devices use signal and supply terminals; 3-wire devices use signal, return, and supply terminal

Input 0 A-0

V1 Return connected to terminals 36, 38, 40,

and 42 +V1 connected to terminals 35, 37, 39,

and 41

Input 1 A-1

Input 2 A-2

Input 3 A-3

Input 4 A-4

Input 5 A-5

Input 6 A-6

Input 7 A-7

Input 8 A-8

Input 9 A-9

Input 10 A-10

Input 11 A-11

Input 12 A-12

Input 13 A-13

Input 14 A-14

Input 15 A-15

Output 0 B-17

V2 Return connected to terminals 44, 46, 48,

and 50 +V2 connected to terminals 43, 45, 47,

and 49

Output 1 B-18

Output 2 B-19

Output 3 B-20

Output 4 B-21

Output 5 B-22

Output 6 B-23

Output 7 B-24

Output 8 B-25

Output 9 B-26

Output 10 B-27

Output 11 B-28

Output 12 B-29

Output 13 B-30

Output 14 B-31

Output 15 B-32

+V1 DC power Power terminals 35, 37, 39, and 41

Com1 DC return Common terminals 36, 38, 40, and 42

+V2 DC power Power terminals 43, 45, 47, and 49

Com2 DC return Common terminals 44, 46, 48, and 50

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

IN0 IN 1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12 IN13 IN14 IN15

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

+V2 = Terminals 43, 45, 47 and 49

Inputs

+V1 COM1 +V1 COM1 +V1 COM1 +V1 COM1 +V2 COM2 +V2 COM2 +V2 COM2 +V2 COM2 NC

+V1 = Terminals 35, 37, 39 and 41

COM1 = Terminals 36, 38, 40 and 42

NC = No connections (terminals 16, 33, 34 and 51)

COM2 = Terminals 44, 46, 48 and 50

NC NC

(1794-TB32 shown)

Outputs

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 OUT15

8Rockwell Automation Publication 1794-IN083E-EN-P - July 2022

FLEX I/O Digital Input and Output Modules Installation Instructions

Configure Your Module

You configure your module by setting bits in the configuration word (word 3).

Set the Input Filter Time

To set the input filter time, set the associated bits in the output image (complementary word) for the module.

For example, to increase the Off to On filter time to 8 ms for all inputs at address rack 1, module group 0, in configuration word 3, set bits as shown.

Filter times are shown in Table 3.

Image Table Memory Map for the 1794-IB10XOB6 Module

Dec 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Oct 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0

Read 1 Not used I9 I8 I7 I6 I5 I4 I3 I2 I1 I0

Write 2 Not used O5 O4 O3 O2 O1 O0

Write 3 Not used FT Not used

WhereI = Input

O = Output

FT = Input filter time for input channels

Image Table Memory Map for the 1794-IB16XOB16P Module

Dec 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Oct 17 16 15 14 13 12 11 10 7 6 5 4 3 2 1 0

Read 1 I15 I14 I13 I12 I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0

Write 2 O15 O14 O13 O12 O11 O10 O9 O8 O7 O6 O5 O4 O3 O2 O1 O0

Write 3 Not used Input filter FT 0...15

WhereI = Input

O = Output

FT = Input filter time for all 16 inputs (0…15)

Table 3 - Input Filter Time

Bits(1)

(1) Use bits 00, 01, and 02 for 1794-IB16XOB16P; use bits 08, 09, and 10 for 1794-IB10XOB6.

Description

02 01 00 Filter Time for Inputs Off to On/On to Off

10 09 03

000Filter time 0 0.25 ms

0 0 1 Filter time 1 0.5 ms

01 0Filter time 2 1.0 ms

0 1 1 Filter time 3 2.0 ms

1 0 0 Filter time 4 4.0 ms

101Filter time 5 8.0 ms

1 1 0 Filter time 6 16.0 ms

111Filter time 7 32.0 ms

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

FT = 0-15

1794-IB10XOB6 only

FT = 0-9 1794-IB16XOB16P

O:010

Dec.

FLL

I:000

Fill File

Source

Destination

Length

#O:010

Write FT to complement

of input module.

Write lter time on system startup.

765432 1 0

110

12 11 10 9 8 7 6 5

= 5 Octal or 5 Decimal

1794-IB16XOB16P

1794-IB10XOB6

= 5 Octal or 5 Decimal

Rockwell Automation Publication 1794-IN083E-EN-P - July 2022 9

FLEX I/O Digital Input and Output Modules Installation Instructions

Specifications

Attribute 1794-IB10XOB6 1794-IB16XOB16P

Number of inputs, current, sinking 10 16

Number of outputs, current, sourcing 6 16

Recommended terminal base unit 1794-TB2, 1794-TB3,1794-TB3S, 1794-TB3K, 1794-TB3SK, 1794-TBKD, 1794-TB37DS 1794-TB32, 1794-TB32S, 1794-TB62DS, 1794-TB62EXD4X15

On-state voltage, input

Min

Nom

Max

10V DC

24V DC

31.2V DC

On-state current, input

Min

Nom

Max

2.0 mA

8.0 mA @ 24V DC

11.0 mA

2.0 mA

8.8 mA @ 24V DC

12.1 mA

Off-state voltage, input, max 5V DC

Off-state current, input, max 1.5 mA

Nominal input impedance 4.8 kΩ2.5 kΩ

Input filter time(1)

Off to On

On to Off

(1) Input Off to On filter time is the time from a valid input signal to recognition by the module. Input On to Off filter time is time from the input signal dropping below the valid level to recognition by the module.

See Table 3 on page 8

On-state voltage range, output

Min

Nom

Max

10V DC

24V DC

31.2V DC (see Figure 1 on page 11)

On-state current, output

Min, per channel

Nom, per channel

Max, per module

1.0 mA

2.0 A

10 A

1.0 mA

0.5 A

8 A

Off-state voltage, output, max 31.2V DC

Output current rating

per output

per module, max 2 A

10 A 0.5 A

8 A

Surge current 4 A for 50 ms, repeatable every 2 s 1.5 A for 50 ms, repeatable every 2 s

Off-state leakage current, max 0.5 mA

On-state voltage drop, max 1V DC @ 2A

0.5V DC @ 1 A 0.5V DC @ 1 A

Output signal delay, max(2)

Off to On

On to Off

(2) Output Off to On or On to Off delay is the time from the module issuing an output on or off until the output actually turns on or off.

0.5 ms

1.0 ms

Isolation voltage 50V (continuous), Basic Insulation Type

Type tested @ 1250V AC for 60 s, between field side and system

No isolation between individual channels

50V (continuous), Basic Insulation Type

Tested @ 2121V DC for 1 s, system to I/O and inputs to outputs

No isolation between individual channels

Flexbus current 50 mA 80 mA

Power dissipation, max 6.0 W @ 31.2V DC 7.0 W @ 31.2V DC

Thermal dissipation, max 20.3 BTU/hr @ 31.2V DC 23.9 BTU/hr @ 31.2V DC

Fusing Module outputs are not fused. Fusing is recommended. If fusing is desired, you

must supply external fusing. Use SAN-O MQ4-3A or Littelfuse 235-003 fuses. Outputs are electronically protected

10 Rockwell Automation Publication 1794-IN083E-EN-P - July 2022

FLEX I/O Digital Input and Output Modules Installation Instructions

General Specifications

Attribute 1794-IB10XOB6 1794-IB16XOB16P

Terminal base screw torque Determined by installed terminal base

Dimensions, approx. (H x W x D) 94 x 94 x 69 mm (3.7 x 3.7 x 2.7 in.)

Input indicators (field side indication) 10 yellow status indicators 16 yellow status indicators

Output Indicators (field side indication) 6 yellow status indicators

External DC power voltage range 10…31.2V DC (includes 5% AC ripple)

External DC power supply current range

8 m A @ 10V DC

15 mA @ 19.2V DC

19 mA @ 24V DC

25 mA @ 31.2V DC

78 mA @ 10V DC

North American temp code T3C

IECEx temp code T3 –

UKEX/ATEX temp code T3

Keyswitch position 2

Enclosure type rating None (open-style)

Weight, approx. 85 g (3.00 oz) 98 g (3.46 oz)

Wire size Determined by installed terminal base

Wiring category(1) 2 – on signal ports

(1) Use this Conductor Category information for planning conductor routing as described in the appropriate System Level Installation Manual. Also see Industrial Automation Wiring and Grounding Guidelines, publication

1770-4.1, for more information.

Environmental Specifications

Attribute 1794-IB10XOB6 1794-IB16XOB16P

Operating temperature

IEC 60068-2-1 (Test Ad, operating cold),

IEC 60068-2-2 (Test Bd, operating dry heat),

IEC 60068-2-14 (Test Nb, operating thermal shock):

-20…+55 °C (-4…+131 °F) 0…55 °C (32…131 °F)

Storage temperature

IEC 60068-2-1 (Test Ab, unpackaged nonoperating cold),

IEC 60068-2-2 (Test Bb, unpackaged nonoperating dry heat),

IEC 60068-2-14 (Test Na, unpackaged nonoperating thermal shock):

-40…+85 °C (-40…+185 °F)

Temperature, surrounding air, max 55 °C (131 °F)

Relative humidity IEC 60068-2-30 (Test Db, unpackaged damp heat): 5…95% noncondensing

Vibration IEC60068-2-6 (Test Fc, operating): 5 g @ 10…500 Hz

Shock IEC60068-2-27 (Test Ea, unpackaged shock):

Operating 30 g

Nonoperating 50 g

Emissions IEC 61000-6-4

ESD immunity IEC 61000-4-2:

6 kV contact discharges

8 kV air discharges

Radiated RF immunity IEC 61000-4-3:

10V/m with 1 kHz sine-wave 80% AM from 80…6000 MHz

EFT/B immunity IEC 61000-4-4:

±3 kV @ 5 kHz on power ports

±2 kV @ 5 kHz on signal ports

IEC 61000-4-4:

±2 kV @ 5 kHz on power ports

±2 kV @ 5 kHz on signal ports

Surge transient immunity IEC 61000-4-5:

±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports

Conducted RF immunity IEC 61000-4-6:

10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz

Rockwell Automation Publication 1794-IN083E-EN-P - July 2022 11

FLEX I/O Digital Input and Output Modules Installation Instructions

Figure 1 - Derating Curve for 1794-IB16XOB16P

Certifications

(When Product Is Marked)(1)

(1) See the Product Certification link at rok.auto/certifications for Declaration of Conformity, Certificates, and other certification details.

Value

c-UL-us

(1794-IB10XOB6 only)

UL Listed Industrial Control Equipment, certified for US and Canada.

See UL File E65584.

UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada.

See UL File E194810.

(1794-IB16XOB16P only)

UL Listed Industrial Control Equipment, certified for US and Canada.

See UL File E322657.

UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada.

See UL File E334470.

UK and CE

UK Statutory Instrument 2016 No. 1091 and European Union 2014/30/EU EMC Directive, compliant with:

EN 61326-1; Meas./Control/Lab., Industrial Requirements

EN 61000-6-2; Industrial Immunity

EN 61131-2; Programmable Controllers

EN 61000-6-4; Industrial Emissions

UK Statutory Instrument 2012 No. 3032 and European Union 2011/65/EU RoHS, compliant with:

EN 63000; Technical documentation

UK Statutory Instrument 2016 No. 1107 and European Union 2014/34/EU ATEX Directive, compliant with:

EN IEC 60079-0; General Requirements

EN IEC 60079-7; Explosive Atmospheres, Protection "e"

II 3 G Ex ec IIC T3 Gc

DEMKO 14 ATEX 1342501X

UL22UKEX2378X

TÜV (1794-IB10XOB6 only)

TÜV Certified for Functional Safety: up to and including SIL 2

KC Korean Registration of Broadcasting and Communications Equipment, compliant with:

Article 58-2 of Radio Waves Act, Clause 3

EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation

IECEx

IECEx System, compliant with:

IEC 60079-0; General Requirements

IEC 60079-7; Explosive Atmospheres, Protection "e"

Ex ec IIC T3 Gc

IECEx UL 14.0066X

CCC CNCA-C23-01 󲰃󱑗󲶎󰹢󱡸󷷪󷸇󲕋󳜷󷨟󱐮 󸿉󴳙󵉐󴉟

CNCA-C23-01 CCC Implementation Rule Explosion-Proof Electrical Products

Morocco Arrêté ministériel n° 6404-15 du 29 ramadan 1436

RCM Australian Radiocommunications Act, compliant with:

EN 61000-6-4; Industrial Emissions

10 20 30 40 50 55 60

Vin

O n–state

Voltage

(V DC)

and

Output

Voltage

(V DC)

Ambient Temperature oC

The area within the curve represents the safe operating range for the module under

various conditions of user supplied DC supply voltages and ambient temperatures.

= All mounting positions (including normal horizontal, vertical,

inverted horizontal) safe operating range

26.4

31.2

Publication 1794-IN083E-EN-P - July 2022 | Supersedes Publication 1794-IN083D-EN-P - July 2018

Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur

Allen-Bradley, expanding human possibility, FactoryTalk, FLEX, Rockwell Automation, and TechConnect are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Connect with us.

Waste Electrical and Electronic Equipment (WEEE)

Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.

At the end of life, this equipment should be collected separately from any unsorted municipal waste.

Rockwell Automation Support

Use these resources to access support information.

Documentation Feedback

Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.

Technical Support Center Find help with how-to videos, FAQs, chat, user forums, and product notification updates. rok.auto/support

Knowledgebase Access Knowledgebase articles. rok.auto/knowledgebase

Local Technical Support Phone Numbers Locate the telephone number for your country. rok.auto/phonesupport

Literature Library Find installation instructions, manuals, brochures, and technical data publications. rok.auto/literature

Product Compatibility and Download Center (PCDC) Download firmware, associated files (such as AOP, EDS, and DTM), and access product release notes. rok.auto/pcdc