Haier ESA410R Manuel utilisateur

Design may vary by model number.

numéro de modèle.

El diseño puede variar conforme al

número de modelo

This user manual is to be only used for

electronic control 5,400 BTU, 6,000

BTU, 8,000 BTU 10,000 BTU and 12,000

BTU Models. - Some models may have

an additional letter after the model

number.

Ce guide d'utilisation doit être utilisé

strictement avec les modèles à

commande électronique de 5,400 BTU,

6,000 BTU, 8,000 BTU, 10,000 BTU et

12,000 BTU. - Sur certains modèles, le

numéro de modèle peut être suivi d'une

lettre.

Este manual del usuario es únicamente

para utilizar los controles electrónicos

modelos 5,400 BTU, 6,000BTU,

8,000 BTU, 10,000 BTU y12,000 BTU.

Algunos de los modelos pueden tener

una letra adicional después del número

de modelo.

ESA410R

ESA412R

User & Care Guide

Guide d'utilisation et d'entretien

Guía de uso y cuidado

Room Air Conditioner

Climatiseur individuel

Aire acondicionado

de uso doméstico

0010586165

ESA405R

ESA406R

ESA408R

ENGLISH

TABLE OF CONTENTS

PRODUCT REGISTRATION

Thank you for purchasing our Haier

product. This easy-to-use manual will guide

you in getting the best use of your product.

Remember to record the model and serial

numbers. They are on a label on the side of

your unit.

Model number

Serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

SAFETY INFORMATION.............................................................................................................2

Important Safety Precautions ................................................................................................ 2-3

Operational Safety & Warnings ..................................................................................................4

INSTALLATION REQUIREMENTS .............................................................................................5

Tools and Parts ............................................................................................................................5

Location Requirements ..............................................................................................................6

Electrical Requirements ......................................................................................................... 7-9

HOW TO INSTALL ....................................................................................................................10

Unpacking the Air Conditioner .................................................................................................10

Preparing the Air Conditioner ............................................................................................10-11

Preparing the Window ..............................................................................................................12

Completing the Installation ......................................................................................................13

USING YOUR AIR CONDITIONER ...........................................................................................14

Starting the Air Conditioner ...............................................................................................14-18

Using the Remote Control ..................................................................................................18-19

Changing the Air Direction .......................................................................................................20

CARING FOR YOUR AIR CONDITIONER ................................................................................21

Cleaning the Air Filter ...............................................................................................................21

Cleaning the Front Panel ..........................................................................................................22

Customer Service .....................................................................................................................22

Normal Sounds of an Air Conditioner ......................................................................................23

TROUBLESHOOTING ..............................................................................................................24

LIMITED WARRANTY ...............................................................................................................25

1. Use this air conditioner only for its intended application as described in this

Use & Care Guide.

2. This air conditioner must be properly installed and use the correct wall

outlet that matches with the air conditioner’s power supply cord in

accordance with the Installation Section of this Use & Care Guide before

it is operated.

3. Never unplug the air conditioner by pulling on the power supply cord.

Always grip the plug firmly and pull straight out from the wall outlet.

4. Replace the power supply cord immediately if it becomes damaged in any

way. A new power supply cord must be purchased from the air conditioner

manufacturer and installed by a qualified technician. DO NOT use a power

supply cord that is cracked, split, cut, or damaged anywhere along its

length or either at the plug end or connector end.

5. Turn off the air conditioner and unplug it from the wall outlet before

performing any cleaning or maintenance.

6. Do not store or use combustible or flammable materials or liquids on

or near the air conditioner.

7. If the wall outlet configuration does not match the plug configuration

on the air conditioner, the wall outlet must be changed by a qualified

electrician.

PAGE 2 SAFETY INFORMATION

ENGLISH

THE INFORMATION IN THIS USE & CARE GUIDE MUST BE

FOLLOWED TO MINIMIZE THE RISK OF PERSONAL INJURY, FIRE,

ELECTRIC SHOCK OR OTHER UNSAFE CONDITIONS.

THE INSTRUCTIONS IN THIS USE & CARE GUIDE ARE NOT MEANT

TO INCLUDE EVERY POSSIBLE CONDITION OR SITUATION THAT

MAY OCCUR. USE CAUTION AND CARE WHEN INSTALLING, OPERATING

AND CLEANING THE AIR CONDITIONER.

WARNING

IMPORTANT SAFETY PRECAUTIONS

SAFETY INFORMATION PAGE 3

ENGLISH

8. This air conditioner contains R410a refrigerant and requires certiﬁed

technicians to use the proper equipment, tools and safety standards that

are approved for this refrigerant. Use only equipment certiﬁed for R410a

refrigerant. In addition, under federal law, all refrigerant must be properly

removed from the air conditioner prior to its disposal.

For responsible disposal of the product, please contact your local

municipality for additional recycling options in your area.

READ AND FOLLOW THE

SAFETY INSTRUCTIONS CAREFULLY.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY PRECAUTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the

State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the

State of California to cause birth defects or other reproductive harm.

ENGLISH

OPERATIONAL SAFETY & WARNINGS

1. This air conditioner contains no consumer serviceable parts. If you have

problems or questions regarding the operation of your air conditioner

always call Haier Customer Service: 1-877-337-3639.

2. Be sure that the air conditioner is properly and securely installed in

the window according to the installation instructions included in this

Use & Care Guide.

3. DO NOT drill any holes in the base or sides of the air conditioner.

4. DO NOT place fingers or objects in the air discharge or air intake in the

front of the air conditioner.

5. DO NOT operate the air conditioner with a protective cover on the

outside section.

6. DO NOT block the air discharge or air intake areas on the front panel.

7. DO NOT block the side louvers on the outside of the air conditioner.

8. DO NOT place any objects either on the indoor or outdoor sections of

the air conditioner

9. Operate the air conditioner with the air filter installed.

10. Keep this Use & Care Guide, carton and packing material for future use

in removing, storing and reinstalling the air conditioner.

PAGE 4 SAFETY INFORMATION

ENGLISH

TOOLS AND PARTS

Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED

PARTS SUPPLIED:

Check that all parts for your speciﬁc air conditioner are included in the parts package.

NOTE: If parts are missing, call Haier Customer Service: 1-877-337-3639.

Phillips head screwdriver

Scissors

Level

Tape measure

Drill and 1/8” bit

Pencil

Remo

Weather seals

te

Side curtain

foam

control 1

3

2 2

1

3

INSTALLATION REQUIREMENTS PAGE 5

ON/OFF

MODE

SPEED

TIMER

TEMP/TIME

IMAGE PART MATERIAL

Top channel Steel

PU

Steel

PS

/

PE

1 1

Foam seal

1

Side bracket

2

Window lock

bracket

1 1

3/8" self-

tapping screws

3 4

1" wood screws

9

Side curtains

2

Side curtain

frames

2 2

8,000BTU

10,000BTU

12,000BTU

5,400BTU

6,000BTU

ENGLISH

PAGE 6 INSTALLATION REQUIREMENTS

IMPORTANT: evresbO all governing codes and ordinances. Check the location where the air

conditioner will be installed. Make sure you have everything necessary for correct

installation.

THE LOCATION SHOULD PROVIDE:

• A grounded electrical outlet within 6 ft. (183 cm) of where the power supply cord exits the air

conditioner, for models: ESA405R, ESA406R, ESA408R , ESA410R, ESA412R

NOTE: oD not use an extension cord, plug adapter, surge protector or multi-outlet adapter.

•

Free movement of air in the room to be cooled.

•

A large enough window opening for the air conditioner. (See Fig.2)

•

Theair conditioner must not be installed in a through-the-wall sleeve or in a wall. It can only be

installed in a double-hung wind

ow.

NOTE: The outside cabinet louvers and air discharge must not be obstructed by bushes, trees,

etc. Air must be able to pass freely through the cabinet louvers. (See Fig.1)

WINDOW INSTALLATION

Window opening measurements:

LOCATION REQUIREMENTS

WIDTH

LENGTH

WIDTH

A-WIDTH

B-HEIGHT

Fig. 2

CABINET LOUVERS

Fig. 1

AIR DISCHARGE

ESA405R

ESA406R

ESA408R

ESA410R

ESA412R

A. Width

24-1/2" - 36" 25" - 36-5/8" 26-1/8" - 37-3/4"

B. Height 13-3/8" 14-9/16" 15-1/8"

ENGLISH

1. DO NOT cut or remove the grounding prong on the attached power supply cord. Doing so may

cause sparks or fire, and voids all warranties. For safety purposes the air conditioner must be

properly grounded.

2. To avoid a fire hazard or possible electric shock, DO NOT use an adapter plug, extension cord,

surge protectors, or multi-outlet adapters with the air conditioner.

3. The power supply cord is equipped with a 3-prong plug which mates with a standard 115 volt

wall outlet to minimize the possibility of electrical shock from this air conditioner.

4. The power supply cord includes a leakage current detection interrupter device (LCDI). A

RESET and TEST button are on the plug case. The device should be tested on a periodic

basis by pressing the TEST button and then the RESET button while it is plugged into the wall

outlet. If the TEST button does not trip or the RESET will not stay engaged, do not use the air

conditioner and contact a qualified service technician.

5. Have the wall outlet and circuit inspected by a qualified electrician to ensure that the wall outlet

is properly grounded.

6. If there is a 2-prong wall outlet present and not a 3-prong wall outlet, it is the responsibility of

the user to have it replaced with a properly grounded 3-prong outlet.

7. The air conditioner should always be plugged into a dedicated electrical outlet which has a

voltage rating that matches the serial label on the side of the air conditioner.

8. The electrical ratings for your air conditioner are listed on the Model/Serial Number label. The

Model/Serial Number label is located on the side of the air conditioner cabinet.

9. Specific electrical requirements are listed in the chart below. Follow the requirements for the

type of plug on the power supply cord.

POWER SUPPLY CORD

Wiring Requirements

•

115-Volt (103.5 min. to 126.5 max.)

•

15-Amp time-delay grounded fuse or circuit breaker

•

Use on single outlet circuit only.

ELECTRICAL SAFETY and WARNINGS

WARNING

INSTALLATION REQUIREMENTS PAGE 7

ELECTRICAL REQUIREMENTS

ENGLISH

PAGE 8 INSTALLATION REQUIREMENTS

REQUIRED GROUNDING METHOD (See Fig.3)

This air conditioner must be grounded. This air conditioner is equipped with

a power supply cord that has a 3 prong grounding plug. The power supply

cord must be plugged into a mating, grounded 3 prong outlet, and grounded

in accordance with all local codes and ordinances. If a mating outlet is not

available, it is the customer’s responsibility to contact a qualified electrician

and ensure that a properly grounded 3 prong outlet is installed.

POWER SUPPLY CORD (See Fig.4)

NOTE: Your air conditioner's plug may differ slightly in appearance from the one shown.

A. Reset button

B. Test button

This room air conditioner is equipped with an a leakage current detection interrupter (LCDI)

power supply cord required by UL. This power supply cord contains a current detection device.

If the power supply cord is crushed, this device will detect current leakage and power will be

disconnected from the air conditioner. If this power supply cord is damaged, it cannot be

repaired and must be replaced with a cord from the product manufacturer. If the power supply

cord is damaged call Haier Customer Service: 1-877-337-3639.

ELECTRICAL REQUIREMENTS cont.

RESET

TEST

A

B

Fig. 4

Fig. 3

ENGLISH

TO TEST YOUR POWER SUPPLY CORD:

1. Plug power supply cord into a mating, grounded 3 prong outlet.

(See Fig.5)

2. Press RESET (on some devices, a green light will turn on).

3. Press TEST (listen for click; Reset button will trip, and on some devices,

a green light will turn off).

4. Press and release RESET (listen for click; Reset button will latch, and on

some devices, a green light will turn on). The power supply cord is ready

for operation.

NOTE:

•

The RESET button must be pushed in completely for proper operation.

(See Fig.6)

•

The power supply cord must be replaced if it fails to trip when the test

button is pressed or fails to reset.

•

DO NOT turn the air conditioner on or off by unplugging the power

supply cord from the outlet. Always turn the air conditioner on or off at

the control panel or by using the remote control.

•

A damaged power supply cord must be replaced with a new power

supply cord obtained from the product manufacturer and installed my

a qualified service professional. It cannot be purchased at a retail store

and must not be repaired by the user.

If the power supply cord is damaged please call Haier Customer Service:

1-877-337-3639.

•

The power supply cord contains no user-serviceable parts.

• Opening the tamper-resistant case voids all manufacturer warranties.

• Electrical shock hazard

• Plug into a mating, grounded 3 prong

outlet.

• Do not remove the ground prong from the

power supply cord.

• Do not use a plug adapter, extension cord,

surge protector, or multi-outlet adapter

• Failure to follow these instructions can

result in injury, fire, or electrical shock.

WARNING

INSTALLATION REQUIREMENTS PAGE 9

ELECTRICAL REQUIREMENTS cont.

RESET

TEST

Fig. 5

RESET

TEST

Fig. 6

REMOVE PACKAGING MATERIALS

•

Remove packaging materials. Save the carton and the foam packaging for storing the unit when

not in use.

NOTE: There are NO internal packing materials inside the air conditioner to remove―Do Not

open the cabinet.

•

Handle the air conditioner gently.

•

Keep the air conditioner upright and level. Do not set the air conditioner on its side, front, back

or upside down.

•

The air conditioner must be standing upright for 2 hours prior to installation and operation.

INSTALL TOP CHANNEL

1. Place the top channel on the top of the air conditioner, lining up

the holes in the top channel with the holes in the top of the unit.

Make sure the channel is facing forward as indicated by the

illustrations. (See Fig.7 & 8)

2. Using 3/8" self-tapping screws, attach the top channel to the top

of the air conditioner. (See Fig.8)

Use three (3) 3/8" self-tapping screws for models:

ESA405R,ESA406R

Use four (4) 3/8" self-tapping screws for models:

ESA408R,ESA410R,ESA412R

UNPACKING THE AIR CONDITIONER

PREPARING THE AIR CONDITIONER

ENGLISH

EXCESSIVE WEIGHT HAZARD

When moving or lifting the air conditioner, use two or more people.

Wear gloves when handling the air conditioner to protect against

possible sharp edges and metal ﬁns.

WARNING

PAGE 10 HOW TO INSTALL

Fig. 7

Fig. 8

Top Channel

3/8" Screw

(Actual Size)

Front

ENGLISH

INSTALL SIDE CURTAINS

NOTE: Attach side curtains to the air conditioner before placing the unit in the window.

1. ecalP the tabbed side of the side curtain in

the track on the right-hand side of the air conditioner cabinet. (See Fig.9)

2. edilS the tabbed side of the side curtain down over

all 3 tracks until the curtain is aligned with the top and bottom

of the air conditioner cabinet. (See Fig.11)

3. edilS the side curtain frame over the top of the side curtain, then

into the channel on the top of the air conditioner and

into the track on the bottom of the air conditioner. (See Fig.12)

4. edilS the side curtain frame as close to the air

conditioner cabinet as necessary to lock the side

curtain to the frame. Gently press the frame until

it clicks. (See Fig.10 & Fig.12)

6. Apply the weather seals provided to the bottom, top & sides

of the window to seal around the perimeter of the air

conditioner. (Fig 13 & 14)

HOW TO INSTALL PAGE 11

5. Repeat above steps for the left-hand side curtain

and frame. Make sure no gaps are left to ensu

re that

air does not escape into or out of the room.

PREPARING THE AIR CONDITIONER cont.

TABBED SIDE OF

SIDE CURTAIN

LOCK EDGE SIDE

OF SIDE CUR

Cut and apply a weather

strip to side of the

curtain frame.(One each

side)

Cut and apply weather

strip to back edge of

the window sill.

TAIN

Fig. 9 Fig. 10

Fig. 11

CLICK

Fig. 12

Fig. 13

Fig. 14

Cut and apply weather strip

to front and bottom edge

of window frame.

PREPARING THE WINDOW

ENGLISH

1. Measure the width of the window opening. (See Fig.15)

2. Mark the center line on the inside of the windowsill

with a pencil.

(See Fig.16)

•

Do not block the air discharge or air intake areas on the front panel.

•

Do not block the louvers on the outside of the air conditioner.

3. Center the air conditioner in the window sill.

Make sure to place the unit so that it is resting on the windowsill

with a ¼" to ½" downward tilt towards the outside. Lower the

window sash behind the top channel to hold the unit in place.

(See Fig.17)

NOTE: The appearance of your model may diﬀer from the one

shown.

4. Loosen the screw located on the lower-right hand corner of the

air conditioner.

5. Slide the side bracket over the screw. The side bracket should be

resting on the window sill.

(See Fig.18)

6. Partially tighten the screw. Secure the unit before tightening completely.

7. Use 1/8" drill bit to drill a starter hole through the holes in the side

bracket.

8. Using two (2) 1" wood screws, attach the side bracket to the

window sill.

9. Repeat for side bracket installation on the left-hand side of the air

conditioner.

NOTES AND WARNINGS:

•

Be sure your air conditioner does not fall out of the window opening during installation

or removal.

PAGE 12 HOW TO INSTALL

Fig. 15

Fig. 16

Fig. 18

WIDTH

LENGTH

HEIGHT

WIDTH

CENTER

WIDTH OF

WINDOW OPENING

CENTER LINE

Top Channel

Lower Window Sash

Fig. 17

ENGLISH

COMPLETING THE INSTALLATION

ATTACH SIDE CURTAINS TO WINDOW

1. lluP the right-hand curtain and frame out until it ﬁts ﬂush to the side

of the window frame.

(See Fig.19)

2. Use a 1/8” drill bit to drill a starter hole through the top hole in the

side curtain and into the window sash.

3. Insert one (1) 1" wood screws through the top hole of the right-

hand curtain and into the window sash.

(See Fig.20)

4. Repeat for the left-hand curtain.

5. Use a 1/8" drill bit to drill a starter hole into the window sill using the

bottom hole in the side curtain as a guide.

6. Insert one (1) 1" wood screws through the bottom hole of

the right-hand curtain and into the window sill.

(See Fig.21)

7. Repeat for the left-hand curtain.

FINAL INSTALLATION

1. Uncoil the included foam seal. (See Fig.22)

2. Insert the foam seal behind the top of the lower window sash

and against the glass of the upper window.

3. ecalP the window lock bracket as shown in the diagram using

a screwdriver. Use a 1/8" drill bit to drill a starter hole through the

hole in the window lock bracket and into the upper window.

(See

Fig.23)

4. Attach the window lock bracket to the upper window with one (1)

1" wood screw to secure the unit in place.

5. gulP unit into a grounded 3 prong outlet.

6. rP

ess RESET on the power supply cord on some devices.

A green light will come on. See “Electrical Requirements"

for

For additional energy savings, measure and cut the adhesive

backed foam sheets, and apply over the side curtains and

frames to seal air leakage.(Fig. 24)

full detail.

HOW TO INSTALL PAGE 13

Fig. 19

Fig. 20

Fig. 22

Fig. 23

Fig. 24

Fig. 21

7.

Side curtain foam

Weather seals

POWER

AUTO RESTART

CLEAN FILTER

TEMP/TIME

FAN

MODE SPEED TIMER

˚F/˚C

hr

HIGH

COOL

ENERGY

SAVE

MED

LOW SLEEP

OFF

ON

AUTO COOLDEHUM

FILTER

RESET

Operating your air conditioner properly helps you to obtain the best possible results.

This section explains how to operate this air conditioner.

STARTING THE AIR CONDITIONER

ENGLISH

IMPORTANT:

• When you turn oﬀ the air conditioner , either at the control panel or with the remote control,

wait at least 3 minutes before turning it back on. This prevents the compressor from

overloading. This 3 minute delay also applies when switching from cool mode to fan and

back.

Note: There is a built in 3 minute delay. You may notice the compressor might not start right

away. This was designed to protect the unit.

• Do not operate your air conditioner in the Cool mode when the outside temperature is below

61°F (16° C). The inside evaporator coil will freeze up, and the air conditioner will not operate

properly.

PAGE 14 USING YOUR AIR CONDITIONER

POWER

FILTER RESET

CLEAN FILTER

INDICATOR

MODE SPEED

TEMPERATURE / TIME

TIMER

MODE SPEED TIMER

TEMP/TIME

CLEAN

FILTER

POWER

AUTO RESTART

FILTER

RESET

FAN

COOL

DEHUM

SLEEP

OFF

ON

AUTO COOL

LOW

MED

HIGH

ENERGY

SAVE

°F/°C

Hr

MODE

SPEED

TIMER

POWER

CLEAN FILTER INDICATOR

TEMPERATURE / TIME

FILTER RESET

1. Carefully remove the clear plastic ﬁlm from the control panel.

2. Press POWER once to turn on the air conditioner.

NOTE: When the air conditioner is ﬁrst plugged in, the LED display will show “88” for 3 seconds.

After the air conditioner is turned on for the ﬁrst time, the display will show the

temperature 72 °F and the fan is automatically set to Low speed and the Mode indicator will

show ENERGY SAVE.

NOTE: To switch the temperature display between Fahrenheit (F) and Celsius(C), the air

conditioner must be plugged in and turned on. On the control panel on the front of the

AC, press the UP and DOWN button at the same time and hold for 3 seconds. The change

cannot be done using the remote control.

3. Select Mode. Refer to “Mode.”

4. Select Speed. Refer to “Speed.”

5. Set Timer. Refer to “T

emp/Time”

6. Reset the ﬁlter. Refer to “Filter Reset”

MODE

1. Press mode until you see the indicator light come on next to the desired setting.

2. Choose Fan, Cool, Energy Save, or Dehum.

FAN― Only the fan runs. Press SPEED to select High, Med or Low fan speed. The display shows

the current room temperature.

NOTE: In fan mode, the temperature cannot be set.

ENERGY SAVE― In this mode the fan runs only when cooling is needed. The fan will run for 3

minute after the compressor shuts oﬀ. The fan then cycles on for 2 minutes

at 10 minute intervals until the temperature in the room is above the set

temperature. The compressor then turns back on.

COOL― Cools the room. Press SPEED to select High,Med , Low or Auto Cool fan speed. Press

the TEMP/TIME up or down arrow button to adjust the

temperature. The fan will run

continuously in cool mode.

DEHUM― Aids in removing humidity from the room. Dehum mode cannot be used to cool room.

NOTE: In Dehum mode, when the set temperature is close to ambient temperature, the

compressor may stop and the fan will run in low speed only.

ENGLISH

STARTING THE AIR CONDITIONER cont.

USING YOUR AIR CONDITIONER PAGE 15

STARTING THE AIR CONDITIONER cont.

SPEED

1. Press FAN SPEED until; you see the indicator light come on next to the desired setting.

2. Choose High, Med, Low or Auto Cool

HIGH―For maximum cooling

MED―For normal cooling

LOW―For minimum cooling

AUTO COOL – Adjusts the fan speed automatically to provide ideal cooling based on the room

temperature.

TIMER OFF

To set the air conditioner to turn oﬀ between 1 hour and 24 hours (The air conditioner must be

ON to set):

1. Press TIMER button until Timer Oﬀ indicator light illuminates. The display will show the

remaining hours before the air conditioner will turn oﬀ.

2. Press the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24

hours.

3. Timer Oﬀ indicator light will remain on. The display will show the left time to Timer Oﬀ.

TIMER ON

To set the air conditioner to turn on bwtween 1 and 24 hours:

1. Press TIMER until Timer On indicator light illuminates. The display will show the remaining

hours before the air conditioner will turn on.

2. Press the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24

hours.

3. Timer On indicator light will remain on. Unit will shut oﬀ and restart.

ENGLISH

PAGE 16 USING YOUR AIR CONDITIONER

ENGLISH

STARTING THE AIR CONDITIONER cont.

TO CLEAR TIMER PROGRAM:

NOTE: Air conditioner can be either on or off.

Press TIMER until Timer indicator light turns off.

TO VIEW OR CHANGE THE REMAINING TIME (IN HOURS):

TIMER OFF

1. Press the TEMP/TIME up or down arrow button to increase or decrease the time.

2. After 5 seconds, the display will show the remaining time to Timer OFF.

TIMER ON

1. Press the TEMP/TIME up or down arrow button to increase or decrease the time.

2. The display will show the remaining time to Timer ON.

NOTE: In TIMER and SLEEP mode, temperature cannot be adjusted.

SLEEP

1. Press the TIMER button to choose Sleep mode. The indicator light will turn on.

2. The temperature will increase by 2˚F 1 hour after the mode is chosen. The temperature then

increases another 2˚F after 1 hour. The unit will hold this temperature for 6 hours then stops.

3. To turn off Sleep mode, press the TIMER button until the indicator light is off.

TEMP/TIME

1. Press the TEMP/TIME up arrow button to raise the temperature. Each time you press the

TEMP/TIME up arrow button, the temperature will go up 1°F until it reaches 86°F (30°C).

2. Press the TEMP/TIME down arrow button to lower the temperature. Each time you press the

TEMP/TIME down arrow button, the temperature will go down 1°F until it reaches 61°F (16°C).

NOTE: After 5 seconds, under Fan mode, the display will show the current temperature. Under

Energy Save,Cool or Dehum mode, the display will show the set temperature.

USING YOUR AIR CONDITIONER PAGE 17

ENGLISH

FILTER RESET

This feature automatically notiﬁes you that the air ﬁlter must be cleaned. The indicator light will

come on after 240 hours of operation. Clean the air ﬁlter (refer to Care and Cleaning), place it back

in the front panel, and press the Filter Reset button. The light will turn oﬀ.

NOTE: The raised dots are Braille for the visually impaired. (See Fig.25)

Remote control may diﬀer in appearance from the image shown.

NOTE: Remove and discard protective ﬁlm prior to use. The remote control runs

on one CR2025 battery (included). Replace battery after 6 months of use,

or when the remote control starts to lose power. To change battery, ﬁrst

Press ON/OFF to turn on the air conditioner.When you ﬁrst press the ON/OFF

button, the air conditioner will operate in Energy Save mode, low fan speed and

temperature of 72°F. You can select any other mode to satisfy your needs.

Fig. 25

ON/OFF

MODE

SPEED

TIMER

TEMP/TIME

remove screw on back panel of remote.

POWER

Mode

Press MODE to choose Fan, Energy Save, Cool or Dehum.

Speed

Press SPEED to choose High, Med, Low or Auto Cool.

TIMER

To set the air conditioner to turn oﬀ after a set amount between 1 hour and 24 hours (unit must

be ON):

1. Press TIMER. Timer OFF indicator light on the air conditioner control panel will illuminate.

2. Press the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24

hours.

3. Timer OFF indicator light on the air conditioner control panel will remain on.

To set the air conditioner to turn on between 1 hour and 24 hours:

1. Press TIMER. Timer On indicator light on the air conditioner control panel will illuminate.

2. Press the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24

hours.

3. Timer On indica

tor light on the air conditioner control panel will remain on.

PAGE 18 USING YOUR AIR CONDITIONER

STARTING THE AIR CONDITIONER cont.

USING THE REMOTE CONTROL

La page charge ...

Haier ESA410R Manuel utilisateur

Ce manuel convient également à

Haier ESA410R Manuel utilisateur

dans d''autres langues

Documents connexes