Maytag MHWZ400TQ - 3.7 cu. Ft. Epic Z Front Load Washer Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
PERFORMANCE SERIES
AUTOMATIC
USE & CARE
WASHER
GUIDE
LAVEUSE AUTOMATIQU E
GUIDE D'UTILISATION ET D'ENTRETIEN
FOR QUESTIONS ABOUT FE£1LJRES, OPER£1ION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE
CAll: 1.800.688.9900
IN CANADA, CAll: 1.800.807.6777
AU CANADA, POUR DES QUESTIONS A PROPOS DES CARACTERISTIQUES, DLJ FONCTIONNEMENT/
RENDEMEN I, DES PIECES, DES ACCESSOIRES OU DLJ SERVICE, COMPOSEZ IE : 1.800.807.6777
VISIT OUR WEBSITE £1 WWW.MAYTAG.COM
IN CANADA, WWW.MAYTAG.CA
OU VISITEZ NOTRE SITE INTERNET
WWW. MAYTAG. CA
PARA OBTENER ACCESO AI MANUAl DE USO Y CUIDADO EN ESPANOI, O PARA OBTENER INFORMACION ADICIONAI ACERCA DE SU PRODUCIO, VISITE: WWW.MAYTAG.COM.
TENGA IISTO SU NI,'JMERO DE MODEl O COMPI ETO. PODR/& ENCONTRAR El NL'JMERO DE MODEl O Y DE SERIE EN IA ETIQUETA UBICADA DEBAJO DE IA TAPA DE IA I AVADORA.
Certified to Sanitize
Certifid pour aseptiser
Designed to use only HE High Efficiency detergent
Con(_ue pour I'utilisation d'un d6tergent HE haute efficacitd seulement
W10285612A
,i_!_ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i_i_i_ii!i¸i!i!i!i!i!i!i!i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_iiiiYiiiiii//li¸il¸iiii_ii,i_ii,i_ii,i_ii,i_ii,i_i_iii_i_ii_il'ii_i_iil'ii_i_iil_i_ii_i_ii_i_ii_ii_i_ii_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_ii_i_i_:_¸ _iii!ii,l,ii_,,¸¸¸¸_;_!_iiiiiiiii_i_ ¸il¸ii_ii_ii¸I¸I¸il¸ii_ii¸ii_ii¸ii_ii¸ii_iil¸ii_i_iil¸I¸iiiii_iiiii_i_i_ii_i_iiiii_ii_iii_ii_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_!_!!
TABLE OF CONTENTS
WASHER SAFETY ...................................................................................................................... 3
INSTALLATION REQUIREMENTS ............................................................................................. 5
Tools and Parts ..................................................................................................................... 5
Options ................................................................................................................................ 5
I.ocation Requirements ......................................................................................................... 6
L-)rain System ........................................................................................................................ 8
Electrical Requirements ........................................................................................................ 9
INSTALLATION INSTRUCTIONS ........................................................................................... 10
Remove Transport System .................................................................................................. 10
Connect the Inlet Hoses ..................................................................................................... 10
Connect the L-)rain Hose ..................................................................................................... 11
Secure the L-)rain Hose ....................................................................................................... 12
I_eve[ the Washer ................................................................................................................ 12
Complete Installation ......................................................................................................... 13
FEATURES AND BENEFITS ...................................................................................................... 14
WASHER USE .......................................................................................................................... 15
Starting Your Washer .......................................................................................................... 15
Using the Proper L-)etergent ................................................................................................ 15
Using the L-)ispenser ........................................................................................................... 16
Pausing or Restarting .......................................................................................................... 17
Changing Cycles, Options, and Modifiers .......................................................................... 17
Status Iights ........................................................................................................................ 18
Cycles ................................................................................................................................. 18
Norman Sounds .................................................................................................................. 20
Options .............................................................................................................................. 20
Modifiers ............................................................................................................................ 20
Laundry Guide ................................................................................................................... 21
LAUNDRY TIPS ....................................................................................................................... 22
I.oading ...............................................................................................................................
Stain Removal Guide .......................................................................................................... 23
WASHER CARE ........................................................................................................................ 24
Cleaning Your Washer ....................................................................................................... 24
Water Inlet Hoses ............................................................................................................... 25
Vacation, Storage, and Moving Care .................................................................................. 25
TROUBLESHOOTING ............................................................................................................. 26
Clothes Care ....................................................................................................................... 29
ASSISTANCE OR SERVICE ....................................................................................................... 30
In the U.S.A ........................................................................................................................ 30
In Canada ........................................................................................................................... 30
Accessories ......................................................................................................................... 30
WARRANTY ............................................................................................................................ 2,1
ii!!i!ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!iiii!il¸!I¸_!_!_!_!_!_!iiiiii__ii_i__ii_i__ii_i__ii_i__ii_i__ii_i__ii_i__ii_iiiiiYiiiiiiI__¸i¸il¸iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiliiilii_ii¸ii_ii_i_iiiii_i_i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiill_iJiiiiiiiiiiiiiii_¸ _!!!i!iiii_!iii_!iii_!iii_!iii_!ii_i_!ii_i_!ii_i_!ii_i_!ii_i_!ii_i_!iii_!iiiiiiiiI_ii_iiii_ii_iii_i_ii_iii_iii_iii_iii_iiii_iiii_ii_ii_i_iii_ii_iiii_i_i_iii_i_ii_i_ii_ii_i_ii_ii_i_ii_ii_i_ii_ii_i_iiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
%
TABLE DES MATIERES
SI_CURITI_ DE LA LAVEUSE ..................................................................................................... 32
EXIGENCES DqNSTALLATION ............................................................................................... 34
Outillage et pi_ces .............................................................................................................. 34
Options .............................................................................................................................. 34
Exigences d'emplacement .................................................................................................. 35
Syst_'me de vidange ............................................................................................................ 37
Sp6cifications 6[ectriques ................................................................................................... 37
INSTRUCTIONS DqNSTALLATION ....................................................................................... 2,8
Elimination des accessoires de transport ............................................................................. 38
Raccordement des tuyaux d'a[imentation ........................................................................... 39
Raccordement du tuyau de vidange ................................................................................... 40
Immobilisation du tuyau de vidange .................................................................................. 41
R6g[age de ['aplomb de [a [aveuse ..................................................................................... 41
Achever ['installation .......................................................................................................... 42
CARACTI_RISTIQUES ET AVANTAGES ................................................................................... 43
UTILISATION DE LA LAVEUSE ............................................................................................... 44
Mise en marche de Ha[aveuse ............................................................................................ 44
Utilisation du d6tergent appropri6 ...................................................................................... 44
Uti[isation du distributeur ................................................................................................... 45
Pause et remise en marche ................................................................................................. 46
Changement des programmes, options et modificateurs ..................................................... 46
T6moins [umineux .............................................................................................................. 47
Programmes ....................................................................................................................... 48
Sons normaux ..................................................................................................................... 49
Options .............................................................................................................................. 49
Modificateurs ..................................................................................................................... 50
Guide de [essivage ............................................................................................................. 51
CONSEILS DE LESSIVAGE ....................................................................................................... 52
Chargement ....................................................................................................................... 52
Guide pour ['6[imination des taches ................................................................................... 53
ENTRETIEN DE LA LAVEUSE ................................................................................................... 54
Nettoyage de Ha[aveuse ..................................................................................................... 54
Tuyaux d'arriv6e d'eau ....................................................................................................... 55
Pr6cautions _ prendre avant [es vacances, un entreposage ou un d6m6nagement ............. 55
DI_PANNAGE .......................................................................................................................... 56
Soin des v6tements ............................................................................................................. 60
ASSISTANCE OU SERVICE ...................................................................................................... 61
Aux Etats-Unis .................................................................................................................... 61
Au Canada ......................................................................................................................... 61
Accessoires ......................................................................................................................... 61
GARANTIE ............................................................................................................................... 62
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
iMPORTANT SAFETY iNSTRUCTiONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry=cleaning solvents, other flammable, or explosive
substances as they give off vapors that could igniteor
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
[] Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
[] Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach into the washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where it will be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user=repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" for grounding instructions.
this time.
SAVE THESEINSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
4,
Gathertherequiredtoolsandpartsbeforestartinginstallation.Thepartssuppliedareinthe
washerdrum.
Tools needed for connecting the water inlet hoses
Pliers (that open to 1%_," [39.5 mm]) Flashlight (optional)
Tools needed for connecting the drain hose
I.ocking pliers (that open to 1%_>" [39.5 mm])
Tools needed for installation
Open end wrenches
14 mmand13 mm
I.eve[
Wood block
Ruler or measuring tape
Parts supplied
If You Have You Will Need to Buy
Drain hose too short 4 ft (1.2 m) drain hose extension kit, Part Number 285863
Water faucets beyond reach 2 longer water fill hoses:
of fill hoses 6 ft (1.8 m) Part Number 76314
10 ft (3.0 m) Part Number 350008
Pedestal
You have the option of purchasing pedestals of different heights separately for this washer. You
may select a 10" (254 mm) or a 15.5" (394 mm) pedestal. The pedestal will add to the total
height of the washer.
c
A. Drain hose form E.Beaded strap
B. Inlet hose (2) £ Drain hose
C. Inlet hose washer (4) C. Hose clamp
D. 7)ansport bolt hole plug (4)
Alternate Parts
Your installation may require additional parts. If you are interested in purchasing one of the
items listed here, call the toll-free number on the cover or in the "Assistance or Service"
section.
If You Have You Will Need to Buy
I_aundry tub or standpipe Sump pump system (if not aheady available)
taller than 96" (2.4 m)
Overhead sewer Standard 20 gal. (76 I.), 30" (762 mm) tall drain tub or
utility sink and sump pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285834; additional drain hose,
Part Number 8318155; and connector kit, Part
Number 285835
Optional pedestal
Pedestal Height Approximate height Color Model Number
with washer
10" (254 ram) 46" (1168 ram) White MHP1000SQ0
10" (254 mm) 46" (1168 mm) Black MHP1000SB0
10" (254 mm) 46" (1168 mm) Cranberry XH P1000WR
15.5" (394 mm) 51.5" (1308 mm) White MHP1500SQ0
15.5" (394 mm) 51.5" (1308 mm) Black MHP1500SB0
15.5" (394 mm) 51.5" (1308 mm) Blue MHP1500SK0
Stack Kit
Are you planning to stack your washer and dryer? To do so, you will need to purchase a
Stack Kit.
To order; call the dealer from whom you purchased your washer or refer to the "Assistance or
Service" section. Ask for Part Number 8572546.
Selectingtheproperlocationforyourwasherimprovesperformanceandminimizesnoiseand
possiblewasher"walk."
Yourwashercanbeinstalledunderacustomcounter,orinabasement,laundryroom,closet,
orrecessedarea.See"DrainSystem."
Companionappliancelocationrequirementsshouldalsobeconsidered.Properinstallationis
yourresponsibility.
You will need
A water heater set to deliver 120°F (49°C) water to the washer.
A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is
attached to the back of the washer. See "Electrical Requirements."
Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves,
and water pressure of 20-100 psi (137.9-689.6 kPa).
A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the
washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not
recommended.
A sturdy and solid floor to support the washer with a total weight (water and load) of
4OO Ibs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the
washer and can cause damage in low temperatures. See "Washer Care" for information on
winterizing.
Installation clearances
The location must be large enough to allow the washer door to be fully opened.
Additional spacing should be considered for ease of installation and servicing. The door
opens more than 90 °, and it is not reversible.
Additional clearances might be required for wall, doo_; and floor moldings.
Additional spacing of 1" (25 mm) on all sides of the washer is recommended to reduce
noise transfen
Companion appliance spacing should also be considered.
Washer Dimensions
501/4''
(I 276ram)
27"
(686 ram)
Door is not reversible.
Recommended installation spacing for custom undercounter installation
The dimensions shown are for the recommended spacing.
Custom undercounter installation - Washer only
37"rain.
(939 ram}
1" _1"_,, 27"--_1÷ 1"
(25 ram) (686 ram) (25 ram)
Recommended installation spacing for recessed or closet installation, with or without
a pedestal
The dimensions shown are for the recommended spacing.
6
Recessed area or closet installation
24 in.2.-
(155cm2)
----_11"_ 301/2,,÷1 4"I'_-"-
(25ram) (775mm) (102ram)
A B
A. Side view - closet or confined area
B. Closet door with vents
*Min. top and bottom air openings for closet door.
Recessed or closet installation - Washer on pedestal
1"_ _ 27"-_ _-- 1" ---_11"I_- 3o,/2"_1 4"I_--
(25ram) (686ram) (25ram) (25ram) (775ram) (102ram)
A B
A. Recessed area
B.Side view - closet or confined area
Recommended installation spacing for recessed or closet installation, with stacked
washer and dryer
The dimensions shown are for the recommended spacing.
48 in.2 *
(310 crn2)
o
24in.2"
(155cm2)
±
3"(76rnrn)
3"(76rnrn)
12"(i05mm)
72"
(1829mm)
(25ram)
_[- 1"(25mm)
*Min. top and bottom air openings for closet door.
** External exhaust elbow requires additional space.
tWa[[, door and floor molding may require additional spacing.
Recommended installation spacing for cabinet installation
The dimensions shown are for the recommended spacing.
For cabinet installation, with a door, the minimum ventilation openings in the top are
required.
7"(178ram)
4" 39/2"
Bn
1" 1" 27" 1"
(102mm)(800ram)(25ram) (25ram)(686ram)(25ram)
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 I.) capacity. The top of the laundry tub must be
at least 30" (762 mm) above the floor.
Floor drain system (view D)
The floor drain system requires a siphon break that may be purchased separately. See "Tools
and Parts."
The siphon break must be a minimum of 28" (710 mm) from the bottom of the washer.
Additional hoses might be needed.
f
{710ram)
D
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub
drain system, or the floor drain system. Select the drain hose installation method you need.
See "Tools and Parts."
Standpipe drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (50 ram). The minimum
carry-away capacity can be no less than 17 gal. (64 I_)per minute.
The top of the standpipe must be at least 30" (762 mm) high and no higher than 96" (2.4 m)
from the bottom of the washer.
30"rnin.
(762mm)
A B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15-or 20-amp, fused electrical supply is required. A time-
delay fuse or circuit breaker is recommended. It is recommended that a separate circuit
serving only this appliance be provided.
This washer is equipped with a power supply cord having a 3 prong grounding plug.
To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,
grounding-type outlet, grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility and obligation of the
customer to have the properly grounded outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the washer is properly grounded.
I)o not have a fuse in the neutral or ground circuit.
GROUNDING iNSTRUCTiONS
For a grounded, cord=connected washer:
This washer must be grounded, in the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING: Improper connection of the equipment=
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment=grounding terminal or lead on
the appliance.
iii!t lii!iiiiiiiiiiii!iiiiiiiiiiiiiiiiiiiiii[_i;!;iiiiiiiiiiiii:]iliiiiiiiiii;iii;iii;iii;iii;iii;iii;iii;iiiiiiiiil¸I¸IIIIIi:iI¸I¸I¸ilii_iii=_=_=_ii_=_=_i_;i;;i_i_;i;;i_i_;i;;i_i_;i;;i_i_;i;;_i_;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;¸ii..............................................................
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
IMPORTANT: Position the washer so that the rear of the washer is within approximately
3 ft (900 mm) of its final location.
There are 4 transport bolts in the rear pane[ of the washer that support the suspension system
during transportation. These bolts also retain the power cord inside the washer until the bolts
are removed.
1. On the back of the washeb loosen the 4 transport bolts using a 13 mm wrench.
2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt,
including the plastic spacer covering the bolt.
Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washer into
the hose couplings.
A B
A. Coupling
B. Washer
Connect the inlet hoses to the water faucets
Make sure washer drum is empty and flat washers have been placed into hose couplings.
1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the
washer.
2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the
washer.
3. Using pliers, tighten the couplings with an additional two-thirds turn.
NOTE: I)o not overtighten or use tape or sealants on the valve. Damage to the valves can
result.
Clear water lines
Run water through both faucets and inlet hoses, into a laundry tub, drainpipe, or bucket,
to get rid of particles in the water lines that might clog the inlet valve screens.
3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord
through the opening of the rear pane[ and dose the hole with the attached cap.
4. Cover the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, ca[[ your local service center. To avoid
suspension and structural damage, your washer must be properly set up for relocation by a
certified technician.
I 0
Checkthetemperatureofthewatertomakesurethatthehotwaterhoseisconnectedto
thehotwaterfaucetandthatthecoldwaterhoseisconnectedtothecoldwaterfaucet.
Remove drain hose from washer drum
1. Use locking pliers, squeeze hose clamp tabs together and insert over the end of drain
hose.
Connect the inlet hoses to the washer
IMPORTANT: Make sure that the flat washers have been placed into the hose couplings.
2. Slide drain hose onto washer connection.
S
C. Cok] water inlet
H. Hot water inlet
1. Attach the hot water hose to the washer's hot (H) water inlet valve. Screw on coupling by
hand until it is seated on the washer.
2. Attach the cold water hose to the washer's cold (C) water faucet. Screw on coupling by
hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.
4. Turn on the water faucets completely and check for leaks.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record
hose installation or replacement dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.
3. Once drain hose is in place, release _liers.
4. Washer drain system can be installed using a floor drain, wall standpipe, floor standpipe,
or laundry tub.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
A B
A. Snap either end of the drain hose form to the drain hose at the point
where the corrugation begins.
B. Bend drain hose over drain hose form and snap into place.
To keep drain water from going back into the washer:
Use the drain hose form, and do not force excess drain hose into standpipe. Hose should
be secure, but loose enough to provide a gap for air.
Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under "Tools and Parts."
Drain hose must be secured to stop the hose from moving when water is pumped out. If the
drain hose moves, water may end up on the floor.
1. Drape the power cord over the washer top.
2. Move the washer to its final location.
3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B.
A
|l
C
NOTES:
I)o not force excess drain hose back into the rear of the washer.
To avoid siphoning, do not sea[ or put more than 4V2' (114 mm) of the drain hose into
drainpipe or standpipe.
4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the
drain hose in the standpipe as shown. See illustration C.
Properly leveling your washer avoids excessive noise and vibration.
NOTE: Installing washer on soft floor surfaces, such as carpets or surfaces with foam backing,
is not recommended.
1. Slide the washer to its final location.
2. Check that all four feet are in firm contact with the floor.
3. Check the levelness of the washer by placing a level on the top edge of the washer, first
side to side then front to back.
4o
If the washer is against a wall, move the washer out slightly before tipping back. If the
washer is not [eve[, first prop the front with a wooden block and adjust the front feet
height moving the hexagonal plastic part as necessary. Repeat to adjust back feet.
Make sure all four feet are stable and resting on the floor. Then check that the washer is
perfectly [eve[ (use a [eve[). Repeat steps 1-3 until washer is [eve[.
12
5.
6.
7.
After the washer is level, and all four feet are in firm contact with the floo_; use a
_)/i_"(14 mm) open-end wrench to turn the Iocknuts on the feet, tightly against the
washer cabinet.
IMPORTANT: All four feet must be tightened. If the [ocknuts are not tight against the
washer cabinet, the washer may vibrate.
The washer should not move front to back, side to side, or diagonally when pushed on its
top edges.
Confirm the levelness of the washer.
1. Check the electrical requirements. Be sure that you have the correct electrical supply and
the recommended grounding method. See "Electrical Requirements."
2. Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water faucets are on.
6.
Check for leaks around faucets and inlet hoses.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7.
8.
9.
Plug into a grounded 3 prong outlet.
Read "Washer Use."
To test and to clean your washe_; measure _/_the detergent manufacturer's recommended
amount of HE High Efficiency detergent for a medium-size load. Pour the detergent into
the detergent dispenser. Select NORMAl., and then select START. Allow the washer to
complete one whole cycle.
Use only HE High Efficiency detergent.
Your new front-loading high efficiency washeb was help conserve to conserve resources and
lower your water and energy bills. The washer is designed to determine and then provide the
amount of water needed for the best performance. The time of operation may be greater for
this new system than for a conventional washer.
Electronic Controls
Flexible electronic controls are easy to use whether you are a beginner or an expert.
Auto Water Level
Adjusting to the size of the load, this feature allows the washer to use the minimal amount of
water needed to clean and rinse the clothes. With a low water level, you can obtain the same
results with smaller amounts of laundry products. Because only the required amount of water
is used, the washer saves energy, too. You can obtain the same washing results for small and
large loads size.
Larger Load Size
Since there is no agitatob you can wash largeb bulkier items such as an average size sleeping
bag. You are also able to wash more clothes at one time, which means fewer loads. You can
wash a pillow or a large stuffed teddy bear.
Spin Speeds
This washer automatically selects the spin speed based on the cycle selected. This factory
setting can be changed, however. This washer offers up to three different spin speed choices.
Thermal Optimizer
The heating system ensures that the wash water is heated to the preset temperature for Super
Wash, Whites, and Sanitary cycles. It also provides "Stepped Cleaning" when using the
Sanitary cycle. "Stepped Cleaning" starts the wash cycle with warm water to remove stains
(such as blood or grass). The Sanitary cycle also helps eliminate 99.9% of K. pneumonia, R
aureginosa and S. aureus, which are three common infectious bacteria. Only sanitary cycle
has been designed to meet the requirements of NSF protocol P1 72 for sanitizing efficiency.
Certified to Sanitize
Add A Garment
Suspension System
To reduce washer "walk" and "off-balance" conditions, your new washer combines:
2 Springs to isolate vibration
3 Shock absorbers at the washer base to minimize movement
Stainless Steel Drum
The stainless steel drum eliminates corrosion and enables higher spin speeds for more water
extraction, helping to reduce drying time.
Adaptive Variable Speed Motor
The motor adapts to the load size and to the cycle selected to give the optimum cleaning,
rinsing, and spinning conditions. The motor can handle slow speeds needed for delicate items
and is powerful enough to drive an average clothes load up to high-speed spin.
This option is available in all wash cycles except Rinse & Spin, Spin Only, and Clean Washer.
When this option is available at the beginning of the cycle, the Add A Garment status light
will illuminate for the first 7 minutes. This washer allows a 7-minute period in which other
garments may be added to a load.
Dynamic Balance
A precision balancing system that allows the washer to reach high-speed spins. The washer
spins faster so that clothes coming out of the washer will have less moisture than with
traditional top load machines. In addition, if the Dynamic Balance system detects off-balance
loads during spinning, it redistributes the clothes so that they are evenly balanced.
Detergent Advantage System Dispenser
The three compartments in the dispenser allow loading of all laundry products before the
washer is started. The products will be dispensed into the wash at the optimal time for high-
performance cleaning. The bleach release system is included in the detergent advantage
system. The detergent is added at the beginning of the cycle, and the bleach is added after the
enzymes have had a chance to do their cleaning. The fabric softener is dispensed in the rinse
cycle or in the EXTRA RINSE, if selected. The Detergent Advantage System Dispenser tray can
be easily removed for cleaning.
Use only HE High Efficiency detergent.
WASHER USE
POWER
ADD A GARMENTpREWASH
WASH
RINSE
SPIN
CLEAN
CONTROLS LOCKED _
DOOR LOCKED
NORMAL
RAPID
DELICATE
EST MATED T MEEMA N N G
START
CANCELQPAUSE/
© ©
SPIN WASH/RINSE
SPEED TEMP
ALL AUTOTEMPcoNTROL
PREWASH
MAX EXTRACT
STAIN CYCLE
EXTRA RINSE
NOTE: The panel shown above may be different from that of your model.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
The following is a guide to using your washer. Please refer to specific sections of this manual
for more detailed information.
Do not store laundry products on the top surface of this washen Vibration is normal during
operation.
Usng I:he
Use only High Efficiency detergents. The package for this type of detergent will be marked
"HE" or "High Efficiency." This wash system, along with less water, will create too much
sudsing with a regular non-HE detergenL Using regular detergent will likely result in washer
errors, longer cycle times, and reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made to produce the right amount
of suds for the best performance. Follow the manufacturePs instructions to determine the
amount of detergent to use. Remember, concentrated detergents such as 2x or higher will use
less detergent based on the load size.
Use only HE High Efficiency detergent.
First Wash Cycle Without Laundry
Before washing clothes for the first time, if not completed during the final installation step,
choose the Normal cycle and run it without clothes. Use only HE High Efficiency detergenL
Use _/_the manufacturer's recommended amount for a medium-size load. This initial cycle
serves to ensure the intedor is clean before washing clothes.
15
For All Wash Cycles
1.
To load washer
Open the washer door by pulling on the handle. Sort laundry according to color and type
of fabric. Place a load of sorted clothes in the washer. Do not overload washer.
Overloading can cause poor cleaning.
The washer can be fully loaded, but not tightly packed. Washer door should close
easily.
Mix large and small items. Avoid washing a single item. I.oad evenly.
Wash small items such as infant socks in mesh garment bags. It is recommended that
more than one garment bag be used and that each garment bag be filled with equal
amounts of material.
When unloading garments, occasionally check under the colored seal/bellow rim at
the front of the tub for small items.
2. Close the washer door by pushing it firmly until the lock clicks. The washer door will
remain locked during the wash cycle.
NOTE: The door can be opened only if PAUSE/CANCEl. is selected while the ADD A
GARMENT light is illuminating or if the cycle has been canceled. See "To cancel a cycle"
in the "Changing Cycles, Options, and Modifiers" section.
3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric
softener compartments. Close drawer slowly to avoid spills. See "Using the Dispenser."
NOTE: Use only HE High Efficiency detergent.
4. Turn on the washer by selecting POWER. Select one of the cycles by turning the cycle
selector. The indicator light for the selected cycle win illuminate. When selecting a Wash
Cycle, the preset Modifiers and Options, Water Temp, and Spin Speed for the selected
cycle win illuminate. The preset settings provide the recommended fabric care for the
selected cycle. See "Cycles."
5. Select the desired OPTIONS such as Prewash, MAX EXTRACT r_*,Stain Cycle, or Extra
Rinse. Not all Options are available with all cycles. See "Options."
6. Select the desired MODIFIERS, such as Spin Speed and Wash/Rinse Temp. Not all
Modifiers are available with all Cycles and Options. See "Modifiers."
7. If desired, select the CYCI.E SIGNAl_. The signal is helpful when you are washing items
that should be removed from the washer as soon as it stops. Press CYCI.E SIGNAl. once to
turn it on. The indicator light win illuminate. Press again to turn it off.
8. To begin the wash cycle immediately
Select and hold START (for approximately 1 second).
If you do not select START within 5 minutes of choosing a cycle, the washer
automatically shuts off.
When the wash cycle is complete, the CI_EAN status light illuminates, the door
unlocks, and the wash load can be removed from the washer. The washer powers
down automatically 5 minutes after the cycle is complete and the Clean light stays on
until the door is opened or PAUSE/CANCEl_ is selected. To power down the washer
manually after the wash cycle is complete, select PAUSE/CANCEl. once.
9.
To begin the wash cycle later
Select DEI.AY WASH until the desired delay time (in hours) shows in the Estimated Time
Remaining display. Select START. The countdown to the wash cycle win show in the
display window.
IMPORTANT: When delaying a cycle, use only powdered detergents in the main wash
compartment since liquid detergents may seep out of the compartment during Delay,
before the wash cycle begins.
Your new washer has a dispenser drawer with three separate compartments for your laundry
products--one is for detergent, one is for liquid chlorine bleach, and one is for liquid fabric
softener. I.aundry products are diluted and dispensed automatically at the proper time during
the wash cycle, making it unnecessary for you to return to the washer during the cycle to add
them.
It is normal for small amounts of water to remain in the dispensers when the wash cycle is
complete.
Do not put laundry products directly into the wash tub. Always use the proper dispensers
when adding laundry products.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type of detergent will be marked
"H E" or "High Efficiency." This wash system, along with less water, win create too much sudsing
with a regular non-HE detergent. Using regular detergent win likely result in washer errors, longer
cycle times, and reduced rinsing performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the
best performance. Follow the manufacturer's instructions to determine the amount of detergent
to use. Remember, concentrated detergents such as 2x or higher will use less detergent based
on the load size.
Use only HE High Efficiency detergent.
To fill dispenser compartments
1. PuN out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
16
3. Pushinthedispenserdrawerslowlyandcompletely(toavoidaspill).
A
_ L___
Dispenser
A. Dispenser release lever
LIQUID BLEAOH
B. Main Wash detergent compartment
C. Liquid chlorine bleach compartment
D. F_bHc softener compartment
C
D
Main Wash detergent compartment
(I.etter B in Dispenser Illustration)
Add liquid or powdered HE detergent to this compartment for your main wash cycle.
Powdered color-safe bleach may be added to the Main Wash compartment along with the
powdered detergent.
Use the measurement device which comes with the detergent. Add no more than the
manufacturer's recommended amount.
NOTE: Overfilling could cause an oversudsing condition.
Chlorine bleach compartment
(I.etter C in Dispenser Illustration)
Add NO MORE THAN 2/,,cup (160 ml_) liquid chlorine bleach to this compartment. The
bleach will be automatically diluted and dispensed at the best time during the first rinse after
the wash cycle. This compartment cannot dilute powdered bleach.
Use only liquid chlorine bleach in this dispensen Do not use this dispenser to add
powdered chlorine or any form of color-safe bleach to your load.
Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not
guess. Follow the manufacturer's directions for proper use.
Do not fill beyond the "MAX" level.
NOTE: Overfilling could cause garment damage.
Fabric softener compartment
(I.etter I)in Dispenser Illustration)
Add Y4cup (60 ml.) liquid fabric softener to this compartment. Fabric softener will be
automatically dispensed in the final rinse or in the EXTRA RINSE, if selected.
Do not fill beyond the "MAX" level.
1o
2.
To pause the washer at any time, select PAUSE/CANCEl .....
To continue the cycle, select and hold START (for approximately 1 second).
Not all Options and Modifiers are available with all Cycles.
Cycles, Options, and Modifiers can be changed anytime before START is selected.
To stop a cycle and select a new cycle
1. Select PAUSE/CANCEl twice.
2. Select POWER.
3. Select desired cycle.
4. Select the desired OPTIONS such as Prewash, MAX EXTRACT rM, Stain Cycle, or Extra
Rinse.
5. Select the desired MOI)IFIERS such as Spin Speed or Wash/Rinse Temp.
6. Select and hold START (for approximately 1 second) to restart the washer at the beginning
of the new cycle.
To cancel a cycle
1. Select PAUSE/CANCEl twice.
2. The washer powers down, the door unlocks, and clothes can be removed.
NOTE: If the water [eve[ or the temperature is too high, the washer will drain automatically
before the door unlocks.
To change Options or Modifiers after the cycle has started
1. Select PAUSE/CANCEl .....
2. Select the desired Spin Speed, Wash/Rinse Temp, or OPTION (such as Prewash, MAX
EXTRACT rM, Stain Cycle, or Extra Rinse). If the modifier or option are not available, the
machine will beep.
3. Select and hold START (for approximately 1 second) to continue the cycle.
1o drain the washer manually
1. Select PAUSE/CANCEl .....
2. Select SPIN Only.
3. Select and hold START (for approximately 1 second) to begin the drain.
4. When the spin is complete, the door unlocks. Items can be removed from the washer.
These lights show which portion of the cycle the washer is operating. They also indicate when
you can add an additional item to the wash cycle and when the controls are locked.
ADDAGARMEN']
PREWASH
WASH
RINSE
SPIN
CLEAN
CONTROLS LOCKED
D0 0 R L0 C KED
Adding items
You can add items to the washer after the wash cycle has started, if the ADD A GARMENT
status Light is iLLuminating. ALLcycles have this feature except Rinse & Spin, Spin OnLy, and
CLean Washer.
To add items
1. SeLect PAUSE/CANCEl.. The washer door unlocks, and items can be added.
2. To continue the cycle, close the door and select and hold START (for approximately
1 second).
NOTE: To add garments after the ADD A GARMENT period is over, the wash cycle needs to
be canceled, the items added, and a new wash cycle started.
Clean
The Clean light comes on when the cycle is complete. The light will stay on until the door is
opened or PAUSE/CANCEl_is selected.
Locking controls
The Control I_ock avoids unintended use of the washer. You can also use the control Lock
feature to avoid unintended cycle or option changes during a cycle. When CONTROI_S
I_OCKED status Light is [it, aLLbuttons are disabled except for PAUSE/CANCEl. and POWER.
You can Lock the controls while the washer is operating.
To lock the controls
SeLect and hold CYCI.E SIGNAl. for 3 seconds.
@ CYCLE SIGNAL
HOLD3SECONDSTO
LOCK/UNLOCKCONTROLS
The CONTROI_S I_OCKEI) status light illuminates.
To unlock the controls
SeLect and hold CYCI.E SIGNAl. for 3 seconds until the CONTROI.S I.OCKED status Light
turns off.
Estimated -time Remaining
The cycle times vary automatically based on your water pressure, water temperature,
detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the load
is unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your
garments. During the unbalance routine the time displayed may pause until this activity is
complete, then resume with the remainder of the cycle. The options you select will also affect
the cycle times that are shown in the Preset Cycle Settings table. The Estimated Time
Remaining can change up to 30 minutes under extreme conditions. If a small load of clothing
is run, the Estimated Time Remaining display will indicate 3 or more minutes, but the cycle
will finish immediately. If a large load of clothing is run, the Estimated Time Remaining
display may indicate 1 minute, but the cycle will take approximately 5 minutes to finish.
Door Locked
When the status light illuminates, the door is locked.
Wash Cycles
Choose Wash Cycle by rotating the Cycle selector knob to the desired cycle. The indicator
light for the cycle selected will illuminate. Each cycle is designed for different types of fabric
and soil levels.
NOTE: The cycle selector shown below may be different from that of your model.
NORMAL
RAPID
WASH
DELICATE
HAND
WASH
SUPER
SPIN
WASH ONLY
RINSE
WHITES-
SPIN
CLEAN
WASHER
Each cycle has a preset cycle time, WASH/RINSE TEMP, SPIN SPEED, and may have
preset Options. The preset settings provide the recommended fabric care for the selected
cycle.
The preset settings can be changed anytime before START is selected. Not all Options and
Modifiers are available with all Cycles. To change settings after the cycle has started,
select PAUSE/CANCEl., then select the desired settings. Select and hold START (for
approximately 1 second) to continue the cycle.
18
PresetCycle Settings
Each cycle has a preset Cycle Time, Water Temp, and Spin Speed. The preset settings provide
the recommended fabric care for the selected cycle. See chart.
Cycle Estimated Time* Wash/Rinse Temp Spin Speed
(hr:min)
Sanitary 3 H Extra Hot High
Whites 2 H Hot High
Super Wash 1:39 Hot High
Normal :56 Warm High
Rapid Wash :34 Warm High
(2-3 items)
Delicate :34 Cold I.ow
Handwash :35 Cold I.ow
Spin Only :14 N/A High
Rinse & Spin :26 Cold High
Clean Washer :56 N/A High
*The cycle times vary automatically based on your water pressure, water temperature,
detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the
load is unbalanced.
Sanitary
Use this cycle to clean heavily soiled, colorfast fabrics. This cycle combines an extra hot
water temperature and fast speed tumbling to help ensure the removal of heavy soils and
stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper
performance during this cycle. Only sanitary cycle has been designed to meet the
requirements of NSF protocol P172 for sanitizing efficiency.
Certified to Sanitize
Whites
This cycle is especially designed for cleaning loads of soiled white fabrics with the addition of
bleach. Hot washing temperatures assure optimal bleach activity. An additional rinse provides
optimal rinse performance to avoid chlorine residue on your laundry. This cycle combines
fast-speed tumbling, longer wash time, and high-speed spin to shorten drying time.
Super Wash
Use this cycle to wash loads of sturdy, colorfast fabrics, and heavily soiled garments. This
cycle combines fast-speed tumbling, longer wash time, and high speed spin to shorten drying
times.
Normal
Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business
clothes, permanent press blends, cottons and linens, and synthetic fabrics. This cycle
combines medium-speed tumbling, high-speed spin, and a load cooling process to reduce
wrinkling.
Rapid Wash
Use this cycle to wash small loads of lightly soiled garments that are needed in a hurry. This
cycle combines fast-speed tumbling, a shortened wash time, and high speed spin to shorten
drying time. I_arge wash loads will result in the machine increasing the wash time.
Delicate
Use this cycle to clean washable silk and ultra delicate garments. (Check label instructions to
make sure that garment is washable.) This cycle gently tumbles and drains without spinning to
gently clean garments and minimize wrinkling. Garments will contain a higher amount of
water at the end of this cycle, because there is a low spin-speed at the end of the cycle.
Use mesh garment bags to wash undergarments such as underwire bras, items with
strings, and small items such as socks.
Handwash
Use this cycle to clean washable woolen and special care garments. (Check label instructions
to make sure that the garment is washable.) Similar to the way garments are hand washed in a
sink, the wash action of this cycle combines periods of extra-low tumbling speeds and
soaking. I_ow spin speeds minimize wrinkling.
Use mesh garment bags as needed.
Spin Only
Use this cycle to drain your washer or to drain and spin your wash load. The spin speed is
preset to high. If desired, you can reduce the spin speed by selecting the speed you want from
the SPIN SPEED modifier.
NOTE: I_oads of synthetics, delicate fabrics, handwashables, and woolens should be drained
with no spin or low spin to avoid fabric stress.
To use Spin Only setting
Select SPIN Only cycle.
Press START.
Rinse & Spin Prewash
Use this cycle to rinse, drain, and spinyour wash load. This cycle combines fast-speed
tumbling and high-speed spin. If desired, you can reduce the spin speed by selecting the
speed you want from the SPIN SPEED modifier.
Rinse & Spin is useful for
I.oads that need rinsing only.
Adding fabric softener to a load using the fabric softener dispenser.
Clean Washer
Use the Clean Washer cycle once a month to keep the inside of your washer fresh and clean.
This cycle uses a higher water level. Use with AFFRESH "_washer cleaner tablet or liquid
chlorine bleach to thoroughly clean the inside of your washing machine. This cycle should
not be interrupted. See "Cleaning Your Washer" in the "Washer Care" section.
IMPORTANT: Do not place garments or other items in the washer during the Clean Washer
cycle. Use this cycle with an empty wash drum.
As with any new product, you will hear sounds that you are not accustomed to. You may hear
various sounds when the door is locked or unlocked, and during the washing, rinsing, or
spinning process. Between changes in wash actions, there will be momentary pauses. You
will hear water spraying and splashing during the wash and rinse cycles. These new sounds
and pauses are part of normal washer operation. See "Troubleshooting."
You can customize your wash by adding options to your cycle selections. You can add or
change an option after starting a cycle anytime before the selected option begins. Not all
options are available with all cycles.
j_ PREWASH
MAX EXTRACT
STAIN CYCLE
EXTRA RINSE
@ CYCLE SIGNAL
HOLD3SECONDSTO
|LOC_UNLOCKCONTROLS
See the "l.aundry Guide" section for an overview of possible options for each Wash Cycle
selection.
If an option is available with a selected cycle, the light for that option will illuminate
when selected.
If an option is unavailable with a selected cycle, there will be a short tone and the light for
that option will not illuminate when selected.
Use this option for loads of heavily soiled items that need pretreatment.
Add detergent to Main Wash compartment of the dispenser drawer.
This option adds tumbling time prior to the selected main cycle. The washer continues
automatically from prewash into the main wash cycle.
Stain Cycle
Use this option for heavily soiled loads that need improved stain treatment. When Stain Cycle
is selected, the water temperature of the selected wash cycle is automatically set to warm. The
water will then be heated to a hot water temperature to aid in stain removal. This option will
provide optimal removal of organic stains such as blood.
Extra Rinse
An extra rinse can be used to aid in the removal of detergent or bleach residue from garments.
This option provides an additional rinse with the same water temperature as the Normal rinse.
Cycle Signal
This signal is helpful when you are removing items from the washer assoon as it stops. Select
ON or OFF.
Preset cycle settings of Wash/Rinse Temperature and Spin Speed can be changed. You can
change a modifier after starting a cycle anytime before the selected Modifier begins. Not all
modifiers are available with all options and cycles.
EX, HOT/COLD
HIG H H0 T /C0 LD
L
_ M ED I DM ,_,_,_W ARM/ WA RM
_,_,_'_L0 W '_'_,_WARM /C 0 LD
i_'i_'N0 SPIN ii_COLD/CO LD
0 ©
SPIN WASH/RINSE
SPEED TEMP
ALL AUTO TEM?
CONTROL
To change the spin speed, select the SPIN SPEED button until the desired setting
illuminates.
To change the water temperature, select the WASH/RINSE TEMP button until the desired
setting illuminates.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Maytag MHWZ400TQ - 3.7 cu. Ft. Epic Z Front Load Washer Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi