Dustbane Hurricane 700 XTT Operations Manual

Operations Manual

Manuel d’opérations

Hurricane 700/850 XTT

Autoscrubbers

Code: 19323 (700 XTT) / 19324 (850 XTT)

Serial Number:

Numéro de série : _____________________

Date of Purchase:

Date d’achat : ________________________

More info / Plus d’info : www.dustbane.ca

2015-04

07779

Fig./Abb./ Рис 1

Fig./Abb./ Рис 2 Fig./Abb./ Рис 3

Fig./Abb./ Рис 4

Fig./Abb./ Рис 5

Fig./Abb./ Рис 6 Fig./Abb./ Рис 7

Fig./Abb./ Рис 8 Fig./Abb./ Рис 9

Fig./Abb./ Рис 10





Fig./Abb./ Рис 11 Fig./Abb./ Рис 12

Fig./Abb./ Рис 13

Fig./Abb./ Рис 14

Fig./Abb./ Рис 16

Fig./Abb./ Рис 15

Fig./Abb./ Рис 17

Fig./Abb./ Рис 18

Fig./Abb./ Рис 19

Fig./Abb./ Рис 20 Fig./Abb./ Рис 21

2

ENGLISH

2

1. TABLE OF CONTENTS

1. TABLE OF CONTENTS ....................................................................................................... 2

2. GENERAL INFORMATION .................................................................................................. 4

2.1 S

COPE OF THE MANUAL

.......................................................................................................4

2.2 I

DENTIFICATION OF THE MACHINE

......................................................................................... 5

2.3 D

OCUMENTATION ANNEXED TO THE MACHINE

....................................................................... 5

3. TECHNICAL INFORMATION............................................................................................... 5

3.1 G

ENERAL DESCRIPTION

...................................................................................................... 5

3.2 L

EGEND

............................................................................................................................. 5

3.3 D

ANGER AREAS

.................................................................................................................. 6

3.4 S

AFETY DEVICES

................................................................................................................ 6

3.5 O

PTIONAL UNITS

................................................................................................................. 6

3.6 A

CCESSORIES

.................................................................................................................... 6

4. INFORMATION ON SAFETY............................................................................................... 7

4.1 S

AFETY STANDARDS

........................................................................................................... 7

5. HANDLING AND INSTALLATION ....................................................................................... 9

5.1 L

IFTING AND CARRYING THE PACKED MACHINE

..................................................................... 9

5.2 C

HECKING THE MACHINE ON DELIVERY

................................................................................ 9

5.3 U

NPACKING

........................................................................................................................ 9

5.4 F

EEDING BATTERIES

......................................................................................................... 10

5.4.1 Batteries: preparation................................................................................................. 10

5.4.2 Batteries: installation and connection......................................................................... 11

5.4.3 Batteries: removal ...................................................................................................... 11

5.5 T

HE BATTERY

-

CHARGER

................................................................................................... 12

5.5.1 Choosing the battery-charger..................................................................................... 12

5.5.2 Preparing the battery-charger .................................................................................... 12

5.6 L

IFTING AND HANDLING THE MACHINE

................................................................................ 12

6. PRACTICAL GUIDE FOR THE USER ............................................................................... 12

6.1 C

ONTROL DEVICES

- D

ESCRIPTION

.................................................................................... 12

6.2 I

NSTALLING AND ADJUSTING THE SQUEEGEE

...................................................................... 13

6.3 M

OVING THE MACHINE

...................................................................................................... 14

6.4 I

NSTALLING AND REPLACING THE BRUSHES

/

DRIVE DISCS

/

ROLLERS

................................... 14

6.4.1 Brush head (models 60-70-80) .................................................................................. 14

6.4.2 Roller head (roller models R) ..................................................................................... 14

6.4.3 Flap adjustment.......................................................................................................... 15

6.5 D

ETERGENTS

- U

SE

.......................................................................................................... 15

6.6 S

ETTING UP THE MACHINE

................................................................................................. 15

6.7 W

ORK

.............................................................................................................................. 16

6.7.1. Additional functions................................................................................................ 17

6.8 S

OME USEFUL SUGGESTIONS FOR THE OPTIMAL USE OF THE MACHINE

................................ 17

6.8.1 Pre-washing ............................................................................................................... 17

6.8.2 Drying......................................................................................................................... 18

6.9 D

RAINING OFF DIRTY WATER

............................................................................................. 18

6.10 D

RAINING OFF CLEAN WATER

............................................................................................ 18

7. PERIODS OF INACTIVITY................................................................................................. 19

8. MAINTENANCE AND BATTERY RECHARGING ............................................................. 19

8.1 R

ECHARGING PROCEDURES

.............................................................................................. 19

9. INSTRUCTIONS FOR MAINTENANCE............................................................................. 20

9.1 M

AINTENANCE

– G

ENERAL RULES

..................................................................................... 20

9.2 R

OUTINE MAINTENANCE

.................................................................................................... 20

9.2.1 Precautions ................................................................................................................ 20

9.2.2 Suction air filter and floating rod: cleaning ................................................................. 20

9.2.3 Squeegee blades: check and replacement ................................................................ 20

3

ENGLISH

3

9.2.4 Fuses: replacement.................................................................................................... 21

9.3 P

ERIODIC MAINTENANCE

................................................................................................... 22

9.3.1 Daily maintenance...................................................................................................... 22

9.3.2 Weekly maintenance.................................................................................................. 22

9.3.3 Basket filter: cleaning ................................................................................................. 22

9.3.4 Six-monthly maintenance........................................................................................... 22

10. HOW TO ORDER SPARE PARTS ................................................................................ 22

11. TROUBLESHOOTING................................................................................................... 24

11.1. H

OW TO OVERCOME POSSIBLE FAILURES

........................................................................... 24

4

ENGLISH

4

2.

GENERAL INFORMATION

Read this manual carefully before starting any operations on this machine

1

.

2.1 Scope of the manual

This manual has been drawn up by the Manufacturer and is considered as an integral part

of the machine.

It defines the purpose for which the machine has been manufactured and contains all

information the operators

2

require.

Besides this manual, which contains the necessary information for the users, other

publications have been issued, which contain the specific information for the technicians

in charge of maintenance

3

.

The constant observance of the instructions guarantee the safety of man and machine,

low running costs, quality results and a longer work life of the machine itself. The non-

observance of the prescribed rules could injure men, damage the machine, spoil the

washed floor and even the environment.

To find the single topics in a fast way, see the descriptive table of contents at the

beginning of this manual.

The paragraphs that are not to be neglected are printed in bold letters and preceded by

symbols illustrated and defined below.

! DANGER

Indicates that attention must be paid to avoid serious consequences that could

cause the death of the personnel or possible damages to health.

 WARNING

Indicates that attention must be paid to avoid serious consequences that could

damage the machine, spoil the environment where the machine is used or cause

economic losses.

i INFORMATION

Particularly important instructions.

In following a policy of constant development and update of the product, the Manufacturer

could implement modifications without any previous notice.

Even though the machine you own is greatly different from the one(s) illustrated in this

manual, safety and information thereof are guaranteed anyway.

1

The definition "machine" substitutes the commercial name to which this manual refers

.

2

People authorised to use the machine without carrying out maintenance operations that require precise technical

knowledge.

3

People having the experience, technical preparation and knowledge of the regulations and laws necessary to carry out

the activity and capable to recognize and avoid possible dangers when handling, installing, using the machine and

carrying out maintenance operations

.

5

ENGLISH

5

2.2 Identification of the machine

The number plate (fig. 1), which is attached at the rear of the machine, shows the

following information:

• model code;

• machine model;

• power supply voltage;

• total rated power;

• serial number (registration number);

• year of manufacture;

• dry weight;

• maximum full load weight;

• steepest slope that can be overcome;

• bar code with serial number;

• Manufacturer’s identification.

2.3 Documentation annexed to the machine

• User's Manual;

• warranty certificate;

• adhesive slips for spare part orders;

• test sheet;

• CE Certificate of conformity.

3. TECHNICAL INFORMATION

3.1 General description

The machine is a sweeping scrubber, which can be used in civil and industrial

environments for sweeping, washing and drying flat, horizontal, smooth or moderately

rough floors, with even surfaces and free from obstacles.

The scrubber distributes on the floor an adequately dosed solution of water and

detergent, and brushes it to remove dirt. Choosing with care the right cleaning detergent

and brushes (or abrasive discs or roller) in the wide range of accessories available, the

machine can adapt itself to all kinds of combinations of floors and dirt.

A liquid suction system, which is embedded in the machine, allows a perfect drying of the

just-washed floor: actually thanks to a suction unit which sucks up the air from the

recovery tank thus creating a vacuum, the squeegee scrapes the dirty water from the

floor, collects it and sends it to the recovery tank.

The storage battery feeding and the high capacity of usable batteries allow the maximum

freedom of movement and endurance at any work conditions.

In addition, thanks to the electronic control drive motor provided with forward and reverse

gear, the floor can easily be cleaned in any direction.

3.2 Legend

The main components of the machine are the following (fig. 2):

• the detergent solution tank (fig. 2, ref. 3): used to contain and carry the mixture of clean

water and detergent;

• the recovery tank (fig. 2, ref. 2): used to collect dirty water sucked up from the floor

during washing;

• control panel (fig. 2, ref. 1);

• head unit (fig. 2, ref. 5): the main element is represented by the brushes/rollers, which

distribute the detergent solution on the floor, removing dirt;

• drive unit (fig. 2, ref. 7): the main element consists of the electronically controlled

gearmotor which is operated via a lever below the machine handgrip and enables the

machine to move forward and back;

6

ENGLISH

6

• squeegee unit (or floor wiper, fig. 2, ref. 8): used to wipe and dry the floor, sucking up

the water spread on the floor;

• battery unit (fig. 2, ref. 6): supplies energy for the machine feeding;

• bonnet (fig. 2, ref. 4).

3.3 Danger areas

A -Tank unit: in presence of certain detergents, danger of irritation for the eyes, skin,

mucous diaphragms, respiratory apparatus and asphyxia. Danger caused by dirt

recovered from the environment (germs and chemical subtances). Danger of crushing

between the recovery tank and solution tank, when the recovery tank is replaced on

the solution tank.

B -Control panel: danger of shortcircuits.

C -Lower part of washing head: danger due to lowering of head and rotation of

brushes/rollers.

D -Top of washing head: danger of crushing between the top of the brush head and the

chassis.

E -Rear wheels: danger of crushing between wheel, chassis and tank.

F - Electrical components box: danger of short circuits.

G -Battery compartment (located within the solution tank): danger of short circuits

between the battery poles and presence of hydrogen during battery charging.

3.4 Safety devices

DEVICE (fig. 3) ACTIVATION FUCTION

A

Emergency button Made active when

pressed.

Interrupts the power

supply.

B

Safety in reverse Safety device to prevent

crushing in reverse.

Cuts in when pressed.

Interrupts reverse

movement of machine.

-

Service brake Comes on automatically

when the drive lever is

released.

The machine gradually

decelerates.

C

Parking and emergency

brake

Press pedal C to

engage. Must be

operated only with the

machine at a standstill

or in case of

emergency: if operated

with the machine

moving, it can cause

damage.

Prevents the machine

moving.

3.5 Optional units

Hour counter: the hour counter accessory is fixed to the control panel (fig. 4, ref. 1). It

displays the number of brush operating hours.

3.6 Accessories

• Bristle brushes/rollers: used for washing delicate floors and for polishing;

• Polipropilene brushes/rollers: used for normal floor washing;

• Tynex brushes/rollers: used to remove accumulated stubborn dirt on resistant floors;

• Drive discs: allow the use of the following discs:

∗ yellow discs: used for washing and polishing marble and similar

surfaces;

∗ green discs: used for washing of resistant floors;

∗ black discs: used for thorough washing of resistant floors with

stubborn dirt.

7

ENGLISH

7

4. INFORMATION ON SAFETY

4.1 Safety standards

Read the User's manual carefully before proceeding with start-up, use,

maintenance, routine maintenance or any other operations on the machine.





 WARNING

Stick to all the instructions contained in this Manual (especially those regarding

danger and warning) and observe the safety plates attached on the machine.

The Manufacturer declines all responsibility for injures to persons or damage to

things deriving from the non-observance of these instructions.

The machine must be used by trained personnel only, who have shown their skill and

have been expressly authorized to use it.

Persons under eighteen cannot use the machine.

This machine must not be used for any other purpose than that for which it has been

expressly manufactured. Assess the type of building in which it will be used (e.g.

pharmaceutical and chemical companies, hospitals, etc.) and scrupulously respect the

regulations and conditions in force.

Do not use the machine in places that are not adequately lighted, in environments with

danger of explosions, on public roads, in the presence of dirt harmful to health or

improper environments.

The suitable temperature for the use of the machine ranges between +4°C and +35°C;

when the machine is not used, the temperature range is between +0°C e +50°C.

The humidity range for the machine under any conditions varies between 30% and 95%.

Never use or suck up inflammable or explosive liquids (e.g. petrol, fuel oil, etc.),

inflammable gases, dry dust, acids and solvents (e.g. solvents for paints, acetone, etc.)

even if diluted. Never suck up any burning or white-hot objects.

Do not use the machine on slopes or ramps higher than 2%; in the event of light slopes

do not use it transversally, handle it with extreme care and do not reverse. When driving

along ramps or heavier slopes take great care to avoid overturning or uncontrolled

acceleration. Overcome ramps and/or steps exclusively with the brush head and

squeegee lifted.

Never

park the machine on slopes.

The machine must never be left unmanned with the motors running; before abandoning

the machine, switch the motors off, ensure that it cannot move accidentally, engage the

parking brake and remove the key from the ignition.

When using the machine mind the presence of people particularly children in the

environment where you are working.

Do not use the machine to carry persons/things or to tow things. Do not drag the

machine.

Never lay things on the machine for any reason.

Do not obstruct the air vents and heat dispersion openings.

Do not remove, modify or elude the safety devices.

Various and unpleasant experiences have shown that people wear or carry various

objects capable of causing serious accidents: before starting to work, remove trinkets,

watches, neckties or other such things.

Always use individual safety protections: apron or protective suit/overalls, non-slip water-

proof shoes, rubber gloves, protective goggles and caps, face mask to protect the

respiratory system.

8

ENGLISH

8

Do not put the hands in between moving organs.

Do not use detergents different from those provided for, and stick to the instructions

indicated on the respective safety sheets. Keep detergents in a safe place, inaccessible

to children, and in case they come in contact with the eyes, wash them immediately with

plenty of water or, if swallowed, call for a doctor immediately.

Make sure that the plugs for the power supply of the models with cable or of the battery-

chargers are properly grounded and protected by magnetothermal switches and

differentials.

Make sure that the electric characteristics of the machine (voltage, frequency, absorbed

power) indicated on the identification plate (fig. 1), are compliant with those of the power

distribution plant. The machine with cable is equipped with three lead wires and a three-

contact ground plug for the use of a proper grounding plug. The yellow and green wire of

the cable is the earth wire: never connect this wire to other wires that are not the plug

ground tap.

It is fundamental to observe the battery Manufacturer’s instructions and stick to the

Legislator’s provisions. Keep batteries always dry and clean to avoid surface leakage

currents. Keep batteries safe from impurities, for instance metal dust.

Do not lay tools on batteries: danger of short circuits and explosions.

Mind the use of battery acid: stick to the relative safety instructions.

When using the machine model with cable mind that you do not crush or tear the power

supply cable. Check this cable periodically to control if it is damaged; if this is so, the

machine cannot be used.

In presence of particularly high magnetic fields assess the possible effects on the control

electronics.

Never wash the machine with jets of water.

The recycled fluids contain detergents, disinfectants, water, organic and inorganic stuff

recycled during the work stages: they must be disposed of in compliance with the laws in

force.

In case of breakdown and/or bad operation of the machine, switch it off immediately

(unplugging it from the mains) and do not tamper with it. Contact a technical assistance

centre of the Manufacturer’s.

All maintenance operations must be performed in adequately lighted environments and

only after having disconnected the machine from the power supply (in models with cable

by unplugging the machine from the socket, while in models with battery by detaching the

battery connector).

Have any electrical work and all maintenance and repair operations (particularly those not

explicitely described in this manual) carried out a specialised and trained technical staff

only.

In case of replacement of the power supply cable, plug or terminals, perform the repair by

properly fixing the electric connections and the cable blocking strap that is located in the

control panel, to guarantee the resistance of the cable. Then reassemble the panel with

care to ensure the protection of the machine user.

Only the use of original accessories and spare parts supplied by the Manufacturer is

permitted, as only these offer the certainty that the machine will operate safely and

without any inconveniences. Do not use parts removed from other machines or other kits

as spares.

This product is classified as RAEE type special waste and is covered by the requisites of

the new environmental protection regulations (2002/96/CE RAEE). It must be disposed of

separately from ordinary waste in compliance with current legislation and standards.

Special waste. Do not dispose of with ordinary waste.

9

ENGLISH

9

Alternatively, the machine can be sent to the Manufacturer for a thorough overhaul.

If the machine is not used anymore, it is recommended that batteries are removed and

deposited at an authorized collecting centre.

Moreover, it is recommended that you make harmless those parts of the machine that

could be dangerous especially to children, who could use the machine for their games.

5. HANDLING AND INSTALLATION

5.1 Lifting and carrying the packed machine





 WARNING

In all lifting operations make sure that the packed machine has been tightly

anchored to the pallet, in order to avoid any overturning or accidental falls.

Loading and/or unloading from the motor vehicles must be performed in an

adequately lighted environment.

The machine, which is packed on a wooden pallet by the Manufacturer, must be loaded

by means of proper handling machines (refer to the EEC provision 89/392/CEE and

following amendments), onto the carrier and, once it has arrived at the appointed

destination, unloaded by similar means.

The brushes and the squeegees are packed in cardboard boxes without pallet.

The packed machine body must be lifted only with a fork lift truck. Handle with care to

avoid bumps or overturnings.

5.2 Checking the machine on delivery

On delivery check with attention that the package and the machine are not damaged. In

the event that the machine has suffered any damages, report so to the carrier; before

accepting the goods, reserve by written the right to present a claim for the refund of the

damages.

5.3 Unpacking





 WARNING

On unpacking the machine, the operator must be provided with the necessary

accessories (e.g. gloves, protective goggles etc.) to limit possible hazards of

accidents.

Unpack the machine in the following way:

• cut and remove the plastic straps with scissors or nippers;

• remove the cardbox;

• remove the envelopes inside the battery compartment (within the solution tank) and

check its contents:

envelope 1: - test sheet;

- warranty coupon;

- user’s and maintenance manual;

envelope 2: - 3 battery bridge with clips;

- 1 pair of tweezers for fuses;

- 1 connector for the battery-charger;

- 2 switch keys;

i INFORMATION

Keep one of the 2 keys safe so that it can be located in case the other one is lost;

the other key is to be inserted in the lock on the mushroom switch.

• depending on the model, remove the metal brackets or cut the plastic straps, which fix

the machine chassis to the pallet;

10

ENGLISH

10

• disengage the parking brake via the pedal ref. C fig. 3;

• let the machine slide down the pallet on an inclined plane, by pushing it into reverse;

• unwrap the brushes/rollers (fig. 5, ref. 1) and the squeegee (fig. 5, ref. 2) from their

packing;

• clean the outside of the machine observing the safety rules;

• after unpacking the machine, you can install the batteries: see respective paragraphs.

If necessary, preserve the wrapping material as it could be used again to protect the

machine in the event of a move or if the machine should be sent to a service centre for

repair.

Otherwise, the material must be disposed of in compliance with the laws in force.

5.4 Feeding batteries

Two different batteries can be fitted on this machine:

• Tubular leak-proof batteries: these batteries require the periodical check of the

electrolyte level. When it is necessary, top up with distilled water alone until the plates

are covered; do not overfill (max. 5 mm. above the plates).

• Gel batteries: this kind of batteries requires no maintenance.

When using this type of battery the fuse FU7 (fig. 6, ref. 2) inside the machine control

panel must be removed using the pliers. This operation serves to inform the electronic

control of the type of battery used.





 WARNING

Do not fit the fuse FU7 if using gel batteries.

The technical specifications must correspond to those indicated in the paragraph

concerning the machine technical data: actually, the use of heavier storage batteries can

cause serious problems to the machine controllability and overheat the drive motor,

whereas storage batteries with a lower capacity require recharges more frequently.

They must be kept charged, dry and clean, with their connections tight.

5.4.1 Batteries: preparation

! DANGER

On installing or performing any kind of maintenance on the batteries wear the

necessary accessories (e.g. protective gloves, goggles, overalls, etc.) to limit the

hazards of accidents, keep away from possible free flames, do not short-circuit the

battery poles, cause sparks or smoke.

The batteries are normally supplied filled with acid and ready-for-use.

If batteries without acid are to be used, before mounting them on the machine, it is

necessary to make them active as follows:

• after taking off the battery plugs, fill up all elements with a solution of specific sulphuric

acid, until the cells are thoroughly covered (fill each element at least twice);

• let them rest for about 4-5 hours, to give time to air bubbles to come up to the surface

and the plates to absorb the electrolyte;

• check that the electrolyte level is still above the plates, otherwise top up with the

solution of sulphuric acid;

• reclose the plugs;

• install the storage batteries on the machine (following the procedure described below).

It is now necessary to perform a first recharging before having the machine start; to do so

stick to the instructions written in the respective paragraph.

11

ENGLISH

11

5.4.2 Batteries: installation and connection

! DANGER

Check that the emergency button on the control panel is at the position “0” (off).

Mind you connect only the clips marked with the symbol “+” to the positive poles.

Do not check the battery charge by creating sparkles.

Stick scrupulously to the instructions described below, as any short circuits of the

batteries may cause them to explode.

1) Stop the machine and press the emergency button (fig. 8, ref. 2); engage the parking

brake by means of the pedal (fig. 8, ref. 12);

2) make sure that the two tanks are empty (empty them, if necessary: see respective

paragraph);

3) unhook the recovery tank (fig. 2, ref. 2) from the solution tank (fig. 2, ref. 3) acting on

the blocking hook (fig. 7, ref. 1), placed on front of the machine;

4) lift the recovery tank, by making it turn backwards around about 90°: in this way you

have access to the battery compartment (embedded in the solution tank) from the

upper side;





 WARNING

Before opening the upper tank:

ensure that the recovery tank is empty (an acoustic warning device will sound if

you try to open the recovery tank without emptying it first);

ensure that the emergency button is pressed.

5) insert the batteries in the compartment, orienting them as shown in the drawing printed

on the solution tank in the compartment.





 WARNING

Install the storage batteries on the machine using suitable means according to

their weight.

Positive and negative poles have different diameters.

6) Referring to the arrangement of cables in the aforesaid drawing, connect the clips of

the battery wiring and the bridge to the poles of the storage batteries. After orienting

the cables as shown in the drawing, tighten the clips at the poles and cover them with

vaseline;

7) insert back the tank unit in its work position and hook it to the solution tank by means

of the fixing hook (fig. 7, ref. 1);

8) use the machine in compliance with the instructions written below.

5.4.3 Batteries: removal

! DANGER

When removing the batteries, the operator must be equipped with suitable personal

protection devices (gloves, goggles, overalls, safety shoes, etc) to reduce the risk

of accidents. Make sure the switches on the control panel are in the "0" position

(off) and the machine is turned off. Keep away from naked flames, do not short

circuit the battery poles, do not cause sparks and do not smoke. Proceed as

follows:

• disconnect the battery wiring and bridge terminals from the battery poles.

• if necessary, remove the devices fixing the battery to the base of the machine.

• lift the batteries from the compartment using suitable lifting equipment.

12

ENGLISH

12

5.5 The battery-charger





 WARNING

Never let the batteries run down excessively, as they could become damaged

irreparably.





 WARNING

Before recharging the batteries, ensure that you have pressed the emergency

button.

5.5.1 Choosing the battery-charger

Check that the battery-charger is compatible with the batteries to be charged:

− tubular lead batteries: an automatic battery-charger 24V - 20A is suggested. Anyway,

refer to the Manufacturer and read the relative manual to confirm your choice;

− gel batteries: use a battery-charger specifically intended for this type of storage

batteries.

5.5.2 Preparing the battery-charger

If you wish to use a battery-charger not supplied with the machine, it is necessary to

mount on it the connector delivered with the machine (see paragraph “Unpacking” of this

manual).

To install the connector proceed as follows:

• remove about 13 mm of sheath from the black and red cables of the battery-charger;

• insert the cables in the connector pins and push strongly with suitable pliers;

• insert the cables in the connector respecting the polarity (red cable +, black cable –).

5.6 Lifting and handling the machine





 WARNING

All stages must be performed in an adequately lighted environment adopting all

necessary safety measures.

Always wear individual protections for the user’s safety.

The loading of the machine onto a vehicle must be done as follows:

• empty the recovery tank and the solution tank;

• remove the squeegee and the brushes (or drive discs);

• remove the batteries;

• place the machine on the pallet, engage the parking brake and secure it with plastic

straps or metal brackets;

• lift the pallet by means of a fork lift truck and load it on the vehicle;

• anchor the machine to the vehicle with ropes connected to the pallet and to the

chassis of the machine.

6. PRACTICAL GUIDE FOR THE USER

6.1 Control devices - Description

With reference to fig. 8 the machine has the following controls and leds:

• Battery charge level indicator (ref. 9): signals both “Power on” and the battery

charge level. Note: the following percentages are based on the usable capacity and

not the total capacity of the batteries (therefore 100% flat = 80% of total battery

capacity). Possible situations are:

a) off: the main switch is set to “0” (off) or the batteries are disconnected;

b) green light: batteries charged from 100% to 50%;

c)

yellow light:

batteries charged from 50% to 15%;

d) red light (also simultaneously with yellow or green light): batteries flat and

13

ENGLISH

13

must be recharged.

• Main switch - emergency button with key (ref. 2): enables or disables the power

supply to all the machine functions. It acts as a safety device.

To start the machine

turn the proper key clockwise. To stop the machine press the button.

• Brush/roller up-down button (ref. 5): when the arrow down is pressed, the head

moves down to the working position, the brush motor comes on automatically and the

solenoid valve is activated. Via this button, a variable pressure can be exerted on the

head during the work phase (according to how long the button is kept pressed), thus

adapting the cleaning power of the brushes to a wide range of different operating

conditions.

When the arrow up is pressed, the head moves up to the rest position, the brush

motors are switched off and the solenoid valve is de-activated.

• Brush pressure indicator (ref. 8): indicates connections of brushes and pressure

exerted by the head (1 led on indicates beginning of brush connection; 2 leds on

indicate minimum pressure; 3 leds on indicate maximum pressure).

• Brush release button (ref. 4): permits release of the brushes; press the button for a

couple of seconds: when the button is released, the brushes will be released.

• Cock control lever (ref. 3): allows to adjust continuously the flow of solution sent to

the brushes. On turning it forward, the liquid outlet flow is increased.

• Drive command lever (ref. 6): placed under the handgrip, when it is slightly pressed

upwards (the emergency button must be active), it starts the drive motor thus making

the machine move forward. When the lever is pressed down, the drive motor moves

the machine in reverse gear.

• Squeegee lifting lever (ref. 11): it allows to raise (when lifted) or lower (when pushed

down) the squeegee. When it is pressed down, the suction motor is also switched on

for drying the floor.

• Hour meter (ref. 7 - optional): displays the hours of work of the brush.

• Parking brake pedal (ref. 12): engages (when pressed and moved to the right) and

disengages (when pressed and moved to the left) the parking brake.

• Potentiometer (ref. 1): permits adjustment of the machine forward and reverse

speed; when the knob is turned clockwise the speed is increased.

6.2 Installing and adjusting the squeegee

The floor wiper, also called squeegee (fig. 2, ref. 8), is the first responsible for drying.

To install the squeegee on the machine proceed as follows:

1) Stop the machine and press the emergency button (fig. 8, ref. 2); engage the parking

brake by means of the pedal (fig. 9, ref. 5);

2) check that the squeegee supporting plate (fig. 9, ref. 2) is raised, otherwise lift it by

acting on the proper lever (fig. 9, ref. 6);

3) firmly push down the sleeve of the suction tube (fig. 9, ref. 4) into the squeegee;

4) slacken the two knobs (fig. 9, ref. 3) placed in the centre of the squeegee;

5) insert the two threaded dowels in the slots of the support (fig. 9, ref. 2);

6) fix the squeegee by tightening the knobs (fig. 9, ref. 3).

The blades of the squeegee are used to scrub from the floor the film of water and

detergent thus allowing a perfect drying. As long as time goes by the continuous scraping

rounds off and splits the sharp edge in contact with the floor, thus reducing the drying

efficacy and therefore requiring the replacement of the blades. Therefore, often check

their state of wear and tear.

To obtain a perfect drying action it is necessary to adjust the squeegee in such a way that

when it is in operation, the rear blade lip is bent about 45 degrees with respect to the floor

at all points. It is possible to adjust the inclination of the blades by screwing down the nuts

(fig. 9, ref. 1): by unscrewing the nuts the blade inclination is reduced, while by screwing

the nuts the blade inclination is increased.

Moreover, check that the suction hole of the squeegee is not clogged, to let dirty water to

14

ENGLISH

14

be perfectly drained from the floor.

6.3 Moving the machine

To displace the machine do as follows:

• lift the squeegee;

• raise the head by pressing the brush up-down button (fig. 8, ref. 5) on the arrow up;

• disengage the parking brake via the pedal (fig. 8, ref. 12);

• insert the key to release the emergency button (fig. 8, ref. 2);

• below the handgrip is a lever (fig. 8, ref. 6): by pulling the lever up (fig. 10, ref. 2) or

pressing it down (fig. 10, ref. 1), according to whether you wish to move forward or

back, the drive motor is switched on and the machine will begin to move;

• adjust the running speed via the potentiometer (fig. 8, ref. 1);

• once you have reached your destination, engage the parking brake via the pedal (fig.

8, ref. 12).





 WARNING

Never leave the machine unmanned or parked with the parking brake disengaged

or the key inserted in the emergency button. Do not engage the parking brake when

the machine is moving.

6.4 Installing and replacing the brushes / drive discs / rollers





 WARNING

Do not work if the brushes or drive discs are not perfectly installed.

6.4.1 Brush head (models 60-70-80)

Removing:

• raise the head by pressing the brush up-down button (fig. 8, ref. 5) on the arrow up;

• press the brush release button (fig. 8, ref. 4) for a couple of seconds: when the button

is released, the brushes will be released.

Fitting:

• position the brushes side by side at the front of the machine;

• move forward with the machine until the head is positioned above the brushes and

they are centred;

• press the brush up-down button (fig. 8, ref. 5) on the arrow down and keep it pressed

until the second led of the brush pressure indicator comes on (fig. 8, ref. 8); in this

phase the brush motor may come on and then switch off for a few moments: this is a

normal part of the brush engagement procedure.





 WARNING

In particular conditions, the brushes may not engage correctly. In this case the

head will vibrate. The brushes must be disassembled and refitted.

If you wish to use the ABRASIVE DISCS instead of the brushes, they must firstly be fitted

on the drive discs: rest the pad on the drive disc, placing it exactly in the centre, and fix it

with the center lock ring nut. The drive discs must then be fitted on the machine following

exactly the same procedure as for the brushes.





 WARNING

Fully tighten the drive disc flange via the handle provided in order to prevent the

flange dragging on the ground and damaging the floor.

6.4.2 Roller head (roller models R)

Disassembly:

• press the roller extraction buttons (fig. 11, ref. 4);

La page charge ...

Dustbane Hurricane 700 XTT Operations Manual

Ce manuel convient également à

Dustbane Hurricane 700 XTT Operations Manual

dans d''autres langues

Documents connexes

Autres documents