Denon DP29FE2GB TURNTABLE SILVER Manuel utilisateur
- Catégorie
- Platines audio
- Taper
- Manuel utilisateur
1
FULLY AUTOMATIC TURNTABLE SYSTEM
DP-29F
OPERATING INSTRUCTIONS
MODE D’EMPLOI
INSTRUCCIONES DE OPERACION
FOR ENGLISH READERS PAGE 05 ~ PAGE 10
POUR LES LECTEURS FRANCAIS PAGE 11 ~ PAGE 16
PARA LECTORES DE ESPAÑOL PAGINA 17 ~ PAGINA 22
45
SPEED
30
17
SIZE
33
45
SPEED
30
17
SIZE
33
2
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is damaged
or deformed, it may cause electric shock or malfunction when
used. When removing from wall outlet, be sure to remove by
holding the plug attachment and not by pulling the cord.
2. Do not open the bottom cover
In order to prevent electric shock, do not open the bottom cover.
If problems occur, contact your DENON dealer.
3. Do not place anything inside
Do not place metal objects or spill liquid inside the turntable
system.
Electric shock or malfunction may result.
Please, record and retain the Model name and serial number of your
set shown on the rating label.
Model No. DP-29F Serial No.
NOTE:
This unit may cause interference to radio and television
reception if you do not operate it in strict accordance with this
OPERATING INSTRUCTIONS.
This unit complies with Class B computing device rules in
accordance with the specifications in Sub-part J or Part 15 of
the FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation.
If the unit does cause interference to any radio or television
reception, try to reduce it by one or more of the following
means:
a) Turn the other unit to improve reception
b) Move this unit
c) Move this unit away from others
d) Plug this unit respectively into a different AC outlet
✽ This is note in accordance with Section 15.838 of the FCC
Rules.
• FOR U.S.A. & CANADA MODEL ONLY
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
• POUR LES MODELES AMERICAINS ET
CANADIENS UNIQUEMENT
ATTENTION
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU
FOND.
IMPORTANT TO SAFETY
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
• CAUTION:
Whenever the turntable is in the “STOP” position, the unit is still
connected on AC line voltage.
Please be sure to unplug the cord when you leave home for, say, a
vacation.
• PRECAUTION:
Quand le tourne-disque est en mode “STOP”, l’appareil est encore
connecté à la tension de ligne secteur.
Prière de s’assurer de débrancher le cordon en quittant la maison
par exemple lors d’un départ en vacances.
• PRECAUZIONI:
Anche quando il giradischi é nella posizione “STOP”, é sempre
collegato al voltaggio AC.
Asegúrese de desconectar el cable de alimentación cuando vaya a
ausentarse de casa (por ejemplo, durante las vacaciones).
FOR EUROPEAN MODELS ONLY
• DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product, to which this
declaration relates, is in conformity with the following standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.
Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC
Directive.
• DECLARATION DE CONFORMITE
Nous déclarons sous notre seule responsabilité que l’appareil, auquel se
réfère cette déclaration, est conforme aux standards suivants:
EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.
D’après les dispositions de la Directive 73/23/EEC, 89/336/EEC et
93/68/EEC.
• DECLARACIÓN DE CONFORMIDAD
Declaramos bajo nuestra exclusiva responsabilidad que este producto al
que hace referencia esta declaración, está conforme con los siguientes
estándares:
EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.
Siguiendo las provisiones de las Directivas 73/23/EEC, 89/336/EEC y
93/68/EEC.
3
SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should
be followed.
5. Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
6. Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water – for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions, and should use a
mounting accessory
recommended by the
manufacturer.
9. A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and
to protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have
been adhered to.
11. Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12. Grounding or Polarization – This product may be equipped with
a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
13. Power-Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the product.
15. Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure A.
16. Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
17. Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of
fire or electric shock.
19. Object and Liquid Entry – Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
20.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
21.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service
personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way,
and
f) When the product exhibits a distinct change in performance
– this indicates a need for service.
22. Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
24. Wall or Ceiling Mounting – The product should be mounted to
a wall or ceiling only as recommended by the manufacturer.
25. Heat – The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
4
ENGLISH FRANCAIS ESPAÑOL
NOTE ON USE /OBSERVATIONS RELATIVES A L’UTILISATION /
NOTAS SOBRE EL USO
• Avoid high temperatures.
Allow for sufficient heat dispersion when installed
on a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
• Evite altas temperaturas.
Permite la suficiente dispersión del calor cuando
está instalado en la consola.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du cordon.
• Maneje el cordón de energía con cuidado.
Sostenga el enchufe cuando desconecte el cordón
d energía.
• Keep the set free from moisture, water, and dust.
• Protéger l’appareil contre l’humidité, l’eau et la
poussière.
• Mantenga el equipo libre de humedad, agua y
polvo.
•
Unplug the power cord when not using the set for
long periods of time.
•
Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
•
Desconecte el cordón de energía cuando no utilice
el equipo por mucho tiempo.
✽ (For sets with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• No obstruya los orificios de ventilación.
• Do not let foreign objects in the set.
• Ne pas laisser des objets étrangers dans l’appareil.
• No deje objetos extraños dentro del equipo.
• Do not let insecticides, benzene, and thinner come
in contact with the set.
• Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
• No permita el contacto de insecticidas, gasolina y
diluyentes con el equipo.
• Never disassemble or modify the set in any way.
• Ne jamais démonter ou modifier l’appareil d’une
manière ou d’une autre.
• Nunca desarme o modifique el equipo de ninguna
manera.
CAUTION
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• Please be care the environmental aspects of battery disposal.
• The apparatus shall not be exposed to dripping or splashing for use.
• No objects filled with liquids, such as vases, shall be placed on the apparatus.
ENGLISH
5
Thank you very much for purchasing the DENON fully automatic turn-
table system.
Please read the operating instructions thoroughly in order to acquaint
yourself with the turntable system and achieve maximum satis-
faction from it.
Please check to make sure the following items are included with
the main unit in the carton:
(1) Operating instructions (these instructions) …………………1
(2) Service station list ………………………………………………1
(3) Platter ……………………………………………………………1
(4) Rubber mat ………………………………………………………1
(5) 45 rpm adaptor …………………………………………………1
z
Precautions …………………………………………………………5
x
Before using the turntable …………………………………………6
c
Connections …………………………………………………………7
v
Controls ………………………………………………………………8
b
Record playback……………………………………………………8, 9
n
Operation details ……………………………………………………9
m
Troubleshooting ……………………………………………………10
,
Specifications ………………………………………………………10
– TABLE OF CONTENTS –
1
PRECAUTIONS
Power requirements
Power requirements for electrical equipment differ from area
to area. Please ensure that your machine meets the power
requirements in your area.
If it doubt, consult a qualified electrician.
About the power switch
This turntable is not equipped with a primary power switch.
The power switch is incorporated in the tone arm of the
turntable. The power to the turntable is cut when the tone arm
returns to the tone arm rest. Note however, that the power is
not completely turned off in this case. If you wish to
completely turn the power off, disconnect the power cord
from the household AC outlet.
What you should know to protect yourself
• Never touch the plug with wet hands.
• Always pull out by the plug and never the cord.
• Only let a qualified professional repair or reassemble the turntable.
An unauthorized person might touch the internal parts and receive
a serious electric shock.
• Never allow a child to put anything, especially metal, into the
turntable.
Protect the turntable too
• Use only a household AC power source. Never use a DC power
source.
• If water is spilled on the turntable, disconnect it and call your
dealer.
• Make sure that the turntable is well ventilated and away from
direct sunlight.
• To avoid damage to the internal circuits and the external surface,
keep it away from heat (stoves, etc.).
• Avoid using spray type insecticide near the turntable it can damage
the finish and might ignite suddenly.
• To avoid damaging the finish, never use paint thinner or other
similar chemicals to clean the turntable.
• Place the turntable on a flat and solid surface.
• If you don’t plan to use the turntable for a long period of time,
disconnect the power cord.
• To protect the insulators, always lift the turntable when you move
it. And before moving the turntable, disconnect all the connecting
cables.
• When transporting the turntable over a long distance, place it in its
original box wrapped in protective wrappers.
ENGLISH
6
2
BEFORE USING THE TURNTABLE
Rubber mat
Spindle
Ribbon tape
Driving roller
Drive belt
Equalizer Amplifier switch
This unit has built-in RIAA equalizer amplifier, so it can be
connected to an amplifier without PHONO (turntable) input
jack. According to the amplifier, set the EQUALIZER
AMPLIFIER SWITCH.
When the unit is connected
to the PHONO (MM) jacks:
Rear panel of the
amplifier
L
R
PHONO
ON
OFF
White
Red
When the unit is connected
to the AUX jacks, etc:
Rear panel of the
amplifier
L
R
AUX
ON
OFF
White
Red
• The drive belt is fitted under the platter. When assembling the
player, please handle the drive belt with care.
• Remove all packing materials attached to the tone arm, except
that on the stylus, and then open the dust cover and assemble.
Remove the stylus cover after assembling.
1
Hold the platter by the holes at its outer surface, and
then carefully lower the platter so that the center
spindle enters the center hole.
Rotate the platter until one of its outer openings is
aligned with the driving roller. (Refer to illustration.)
2
3
Gently grasp and pull at the ribbon tape of the drive
belt that is would under the turntable, and then
extend the belt around the driving roller. (After
attaching, remove the ribbon tape.)
In order to make sure that the drive belt has been
correctly fitted, slowly rotate the platter 3 or 4 turns.
Place the rubber mat on the platter.
IMPORTANT! Please Check.
Check that the drive belt and ribbon tape have been attached
under the platter. Grasp the ribbon tape as shown in the
illustration to the left, and extend it onto the driving roller.
L
R
L
R
L
R
SIGNAL
GND
12
SYSTEM
CONNECTOR
L
R
SPEAKER SYSTEM
SPEAKER IMPEDANCE
4 16
CD
DVD/AUX
TUNER PHONO TAPE MD
AUX-2 TAPE MD
PB
REC
INPUTS
L
R
L
R
1
ENGLISH
7
3
CONNECTIONS
Before beginning
• Turn off components.
• Connect the power cord last.
• Connect everything securely. Loose connections can lead to
distortion.
• To prevent damage to cords, connect and disconnect by holding
the plug, not the cord.
• Make sure that you connect the white PIN-plug to the left (L-
white) jack and the red PIN-plug to the right (R-red) jack.
Power cord and plug
Left (White) and Right (Red)
out PIN-plugs
Ground wire
DP-29F Amplifier
Connections
1
Connect the Left and Right PIN-plugs of the
turntable’s output cord to your amplifier’s PHONO
jacks etc.
2
3
Connect the ground wire of the turntable to your
amplifier’s SIGNAL GND (Ground) terminal securely.
After all connections have been made.
• Connect the turntable’s power cord to the AC OUTLET
of your stereo amplifier, optional audio timer or directly
to a household AC outlet.
NOTE:
• If the platter starts rotating when the power cord is
connected, press the STOP button once.
3
2
ENGLISH
8
4
CONTROLS
q
Dust cover
w
Dust cover hinge
e
45 rpm adaptor and holder
r
Equalizer amplifier switch
t
Finger lever
y
Size select lever
u
STOP button
• To stop playback.
i
START button
• To start playback.
o
Cartridge
!0
Tone arm rest
• Holds the tone arm.
!1
Platter
!2
Spindle
!3
Rubber mat
!4
SPEED button (33 £ / 45 ¢ )
• To select the playback speed.
5
RECORD PLAYBACK
Before beginning
• Turn on all the components.
• Set your amplifier’s input selector to PHONO or AUX.
• Remove the stylus cover before playback.
• Use the provided 45 rpm adaptor when playing back 17 cm
records (provided the center hole is a large one).
1 243
q we r
tyuio
!0!1!2!3!4
ENGLISH
9
1
Open the dust cover and place the record you wish
to playback on the platter.
2
Set the SPEED button according to the record
playback speed.
• 33-1/3 rpm record.......................................Set to 33 £
• 45 rpm record.............................................Set to 45 ¢
3
Set the selector lever according to the record size.
4
Press the START button firmly for at least 1 second.
• The platter will start rotating, and playback will start
automatically.
After the full record has been played, the tone arm will return
to the tone arm rest and the platter stops rotating
automatically.
To stop playback
Press the STOP button.
Playback will stop and the tone arm will return to the tone arm
rest.
On the automatic playback system
• Do not touch the tone arm and platter or turn off the power during
playback.
• The auto return system is set to return the tone arm at a specific
point on the record. There should be no problem with regular sized
records, but with some record types which contain music grooves
past this set point, playback will be interrupted.
• 25 cm records cannot be used with the automatic playback
system. Playback these records manually. If the auto return
system does not engage after playback is finished, press the
STOP button.
6
OPERATION DETAILS
Manual playback
1
Place the record you with to play back on the platter.
2
Set the SPEED button according to the record.
3
Take hold of the finger lever, and move the tone arm
to a point just above the beginning of the track you
wish to play.
• The platter will start to rotate.
Stylus replacement
To provided stylus should be changed after approximately 400
hours of record playback. Grasp the cartridge firmly with one
hand, and gently pull the stylus free from the cartridge with
the other hand. Replace the stylus with the DSN-82.
Before replacing the stylus
Turn off the turntable and your amplifier.
Stylus
Stylus
q
w
w
q
123
10
ENGLISH
7
TROUBLESHOOTING
No power.
Platter is not turning.
• Power cord is not connected properly. Check the power cord
connection.
• The drive belt is not fitted to pulley. Check the drive belt.
No sound.
• The output cords are not connected properly. Connect them
securely to your amplifier’s PHONO or AUX jacks.
• The input selector on your amplifier is not set to PHONO or AUX.
Set to PHONO or AUX.
Scratching noise.
Stylus jumps.
Distorted sound.
• Dirty stylus or record. Clean both the stylus and record before
playback.
• Worn out stylus or record. Replace stylus or record.
Howling.
• The turntable is too close to the speaker system. Move it away
from the speaker system.
• The turntable is placed in an unstable location. Place it on a flat and
solid surface.
• The playback volume is too high. Turn down the volume control of
your amplifier.
Humming noise.
• The ground wire is not connected to the SIGNAL GND (Ground)
terminal of your amplifier. Connect it to the SIGNAL GND (Ground)
terminal securely.
The tone arm will not move when pressing the START button.
• The tone arm is locked to the tone arm rest. Remove the tone arm
lock before playback.
Should a problem persist, write down the model and serial number
and all pertinent data regarding warranty coverage as well as clear
description of the existing trouble. Then contact your nearest
authorized DENON service station.
8
SPECIFICATIONS
Drive system: Belt drive
Motor: DC servo motor
Speed: 33-1/3 and 45 rpm
Wow & flutter: 0.15% WRMS
Tone arm: Dynamic balanced type
Effective arm length: 195 mm
Stylus pressure
adjustment range: 3.5 g (fixed)
Cartridge: DSN-82
Output voltage: 2.5 mV
Optimal stylus pressure: 3.5 g
Power supply: AC 120 V, 60 Hz (U.S.A. & Canada)
AC 230 V, 50 Hz (Europe)
Power consumption: 2 W
Dimensions: 360 (W) x 97 (H) x 357 (D) mm
14-3/16(W) x 3-13/16(H) x 14-1/16(D) in
Mass: 2.8 kg (6.2 lbs)
For improvement purposes, specifications and design are subject to change without notice.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Denon DP29FE2GB TURNTABLE SILVER Manuel utilisateur
- Catégorie
- Platines audio
- Taper
- Manuel utilisateur