DeWalt D28402B Manuel utilisateur

Marque: DeWalt

Modèle: D28402B

Catégorie: Meuleuses d'angle

Taper: Manuel utilisateur

D28110, D28112, D28402, D28402N

Heavy-Duty Small Angle Grinder

Petites meuleuses angulaires de service intensif

Esmeriladoras angulares pequeñas para trabajo pesado

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

OR ANY D

EWALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

EWALT (1-800-433-9258)

General Safety Rules – For All Tools

WARNING! Read and understand all instructions.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches

and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operat-

ing a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly

installed and grounded in accordance with all codes and

ordinances. Never remove the grounding prong or modify

the plug in any way. Do not use any adaptor plugs. Check

with a qualified electrician if you are in doubt as to whether

the outlet is properly grounded. If the tools should electrical-

ly malfunction or break down, grounding provides a low resist-

ance path to carry electricity away from the user. Applicable

only to Class I (grounded) tools.

• Double insulated tools are equipped with a polarized plug

(one blade is wider than the other.) This plug will fit in a

polarized outlet only one way. If the plug does not fit fully in

the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install a polarized outlet. Do not

change the plug in any way. Double insulation eliminates

the need for the three wire grounded power cord and grounded

power supply system.

Applicable only to Class II (double

insulated) tools.

• Avoid body contact with grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk

of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools

or pull the plug from an outlet. Keep cord away from heat,

oil, sharp edges or moving parts. Replace damaged cords

immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor

extension cord marked “W-A” or “W.” These cords are rated

for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized cord will

cause a drop in line voltage resulting in loss of power and over-

heating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gage. The smaller the gage number,

the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

English

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use tool while

tired or under the influence of drugs, alcohol, or medica-

tion. A moment of inattention while operating power tools may

result in serious personal injury.

• Dress properly. Do not wear loose clothing or jewelry.

Contain long hair. Keep your hair, clothing, and gloves away

from moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and

should also be avoided.

• Avoid accidental starting. Be sure switch is off before plug-

ging in. Carrying tools with your finger on the switch or plugging

in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool

on. A wrench or a key that is left attached to a rotating part of

the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all

times. Proper footing and balance enables better control of the

tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust

mask, non-skid safety shoes, hard hat, or hearing protection

must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body is unstable and may lead to loss of control.

• Do not force tool. Use the correct tool for your application.

The correct tool will do the job better and safer at the rate for

which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool

that cannot be controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source before making

any adjustments, changing accessories, or storing the tool.

Such preventative safety measures reduce the risk of starting

the tool accidentally.

• Store idle tools out of reach of children and other untrained

persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and

clean. Properly maintained tools, with sharp cutting edges are

less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, break-

age of parts, and any other condition that may affect the

tool’s operation. If damaged, have the tool serviced before

using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manu-

facturer for your model. Accessories that may be suitable for

one tool, may become hazardous when used on another tool.

SERVICE

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by unqualified

personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts.

Follow instructions in the Maintenance section of this man-

ual. Use of unauthorized parts or failure to follow maintenance

instructions may create a risk of electric shock or injury.

Additional Specific Safety Instructions

for Grinders

• Check that the grinding wheel backing flange has a yellow

rubber ring (S) installed, see Figure 1. Replace rubber ring if

missing, damaged or worn. See page 9 for details regarding

proper accessory installation.

WARNING: The grinding wheel or accessory may loosen

during coast-down of the tool when shut off if rubber ring is

English

missing or damaged. If grinding wheel or accessory loosens, it

may dismount from the machine and may cause serious personal

injury.

• Always use proper guard with grinding wheel. A guard pro-

tects operator from broken wheel fragments and wheel contact.

• Accessories must be rated for at least the speed recom-

mended on the tool warning label. Wheels and other acces-

sories running over rated speed can fly apart and cause injury.

Accessory ratings must be above listed minimum wheel speed

as shown on tool nameplate.

• Hold tool by insulated gripping surfaces when performing

an operation where the cutting tool may contact hidden

wiring or its own cord. Contact with a “live” wire will make

exposed metal parts of the tool “live” and shock the operator.

• Do not use Type 11 (flaring cup) wheels on this tool. Using

inappropriate accessories can result in injury.

• ALWAYS WEAR EYE PROTECTION WHEN USING THIS

TOOL.

• Use of accessories not specified in this manual is not rec-

ommended and may be hazardous. Use of power boosters

that would cause the tool to be driven at speeds greater than its

rated speed constitutes misuse.

• Do not use circular saw blades or any other toothed blades

with this tool. Serious injury may result.

• When starting the tool with a new or replacement wheel, or

a new or replacement wire brush installed, hold the tool in

a well protected area and let it run for one minute. If the

wheel has an undetected crack or flaw, it should burst in less

than one minute. If the wire brush has loose wires, they will be

detected. Never start the tool with a person in line with the

wheel. This includes the operator.

• Avoid bouncing the wheel or giving it rough treatment. If this

occurs, stop the tool and inspect the wheel for cracks or flaws.

• Direct sparks away from operator, bystanders or flammable

materials. Sparks may be produced while cutting and/or

grinding. Sparks may cause burns or start fires.

• Always use side handle. Tighten the handle securely. The

side handle should always be used to maintain control of the tool

at all times.

• Never cut into area that may contain electrical wiring or

piping. Serious injury may result.

• Clean out your tool often, especially after heavy use. Dust

and grit containing metal particles often accumulate on interior

surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time. Vibration

caused by the operating action of this tool may cause permanent

injury to fingers, hands, and arms. Use gloves to provide extra

cushion, take frequent rest periods, and limit daily time of use.

• Direct the Dust Ejection System (DES) away from operator

and coworkers. Serious injury may result (Fig. 1, K).

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V..........volts A..............amperes

Hz........hertz W ............watts

min ......minutes ..........alternating current

....direct current

o............no load speed

........Class II Construction ..........safety alert symbol

........earthing terminal …/min ....revolutions per minute

Causes and Operator Prevention

of Kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned

wheel, wire brush or flap disc causing an uncontrolled cut-off

tool to lift up and out of the workpiece toward the operator.

English

• When the wheel is pinched or bound tightly by the workpiece,

the wheel stalls and the motor reaction drives the unit rapidly

back toward or away from the operator.

• Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

• Maintain a firm grip with both hands on the unit and posi-

tion your body and arm to allow you to resist kickback

forces. Kickback forces can be controlled by the operator, if

proper precautions are taken.

• When wheel is binding, or when interrupting a cut for any

reason, release the trigger and hold the unit motionless

in the material until the wheel comes to a complete stop.

Never attempt to remove the unit from the work or pull

the unit backward while the wheel is in motion or kick-

back may occur. Investigate and take corrective actions to

eliminate the cause of wheel binding.

• When restarting a cut-off tool in the workpiece, check

that the wheel is not engaged into the material. If wheel is

binding, it may walk up or kickback from the workpiece as the

tool is restarted.

• Support large panels to minimize the risk of wheel pinch-

ing and kickback. Large panels tend to sag under their own

weight. Support must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chem-

icals known to cause cancer, birth defects, or other reproductive

harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these chem-

icals: work in a well ventilated area, a nd work with approved safe-

ty equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust,

which may cause serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appro-

priate for the dust exposure. Direct particles away from face and

body.

CAUTION: Use extra care when working into a corner because

a sudden, sharp movement of the grinder may be experienced

when the wheel or other accessory contacts a secondary surface

or a surface edge.

CAUTION: Wear appropriate personal hearing protection

during use. Under some conditions and duration of use, noise

from this product may contribute to hearing loss.

COMPONENTS (Fig. 1)

A. Paddle Switch H. Threaded Clamp Nut

(D28402, D28402N) I. Guard

B. Lock-Off Lever J. Lock On Button (D28402)

C. Spindle Lock Button K. Dust Ejection System

D. Spindle (not shown) (DES)

E. Side Handle L. Slider Switch (D28110,

F. 4-1/2" Grinding Wheel D28112)

G. Anti-Lockup Backing Flange

English

FIG. 1

D28110

D28402

D28402N

D28112

ASSEMBLY AND ADJUSTMENTS

ATTACHING SIDE HANDLE

The side handle (E) can be fitted to either

side of the gear case in the threaded holes,

as shown. Before using the tool, check that

the handle is tightened securely. Use a

wrench to firmly tighten the side handle.

Rotating the Gear Case

Turn off and unplug tool before making

any adjustments or removing or installing

accessories. Before reconnecting the tool,

depress and release the trigger switch

to ensure that the tool is off.

1. Remove guard and flanges from tool.

2. Remove the four corner screws

attaching the gear case to motor

housing.

3. Separating the gear case from motor

housing not more than 1/4", rotate the

gear case head to desired position.

NOTE: If the gear case and motor housing become separated by

more than 1/4", the tool must be serviced and re-assembled by a

EWALT service center. Failure to have the tool serviced may

cause brush, motor and bearing failure.

3.Re-install screws to attach the gear case to the motor housing.

Tighten screws to 18 in./lbs. torque. Overtightening could cause

screws to strip.

Accessories

It is important to choose the correct guards, backing pads and

flanges to use with grinder accessories. See pages 6–7 for infor-

mation on choosing the correct accessories.

90˚

(D28402)

English

WARNING: Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels and other acces-

sories running over rated accessory speed may burst and cause

injury. Threaded accessories must have a 5/8"-11 hub. Every

unthreaded accessory must have a 7/8" arbor hole. If it does not,

it may have been designed for a circular saw and should not be

used. Use only the accessories shown on pages 6–7 of this man-

ual. Accessory ratings must be above listed minimum wheel

speed as shown on tool nameplate.

Mounting Guard

MOUNTING AND REMOVING GUARD

(D28112, D28402, D28402N)

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, depress and release the

paddle switch to ensure that the tool is off.

CAUTION: Guards must be used with all grinding wheels,

sanding flap discs, wire brushes, and wire wheels. The tool

may be used without a guard only when sanding with conventional

sanding discs. Some D

WALT models are provided with a guard

intended for use with depressed center wheels (Type 27) and

hubbed grinding wheels (Type 27). The same guard is designed for

use with sanding flap discs (Type 27 and 29) and wire brushes.

Grinding and cutting with wheels other than Type 27 and 29 require

different accessory guards not included with tool. Mounting

instructions for these accessory guards are included in the acces-

sory package.

Type 27 guard

4-1/2" Grinding Wheels

backing flange

threaded clamp nut

Type 27 hubbed wheel

Type 27 guard

Type 27 depressed

center wheel

Wire Wheels

3" wire cup

brush

4" wire wheel

Type 27 guard

English

1. Open the guard latch (M). Align

the lugs (N) on the guard with the

slots (O) on the gear case.

2. Push the guard down until the

guard lugs engage and rotate

freely in the groove on the gear

case hub.

3. With the guard latch open, rotate

the guard (I) into the desired working po

sition. The guard body should be posi-

tioned between the spindle and the

operator to provide maximum operator

protection.

4. Close the guard latch to secure the guard on the gear case.

You should not be able to rotate the guard by hand when the

latch is closed. Do not operate the grinder with a loose guard or

the clamp lever in open position.

5. To remove the guard, open the guard latch, rotate the guard so

that the arrows are aligned and pull up on the guard.

NOTE: The guard is pre-adjusted to the

diameter of the gear case hub at the factory.

If, after a period of time, the guard becomes

loose, tighten the adjusting screw (P) with

clamp lever in the closed position.

4-1/2" Sanding Flap Discs

hubbed sanding

flap disc

backing flange

non-hubbed sanding

flap disc

threaded clamp nut

rubber backing pad

sanding disc

threaded clamp nut

Sanding Discs

4-1/2" Cutting Wheels

Type 1 guard

backing flange

abrasive cutting wheel

clamp nut

Type 1 guard

backing flange

diamond cutting wheel

clamp nut

Type 27 guard

English

CAUTION: Do not tighten the adjusting screw with the clamp

lever in open position. Undetectable damage to the guard or the

mounting hub may result.

CAUTION: If guard cannot be tightened by adjusting clamp, do

not use tool and take the tool and guard to a service center to repair

or replace the guard.

MOUNTING AND REMOVING GUARD

(D28110)

1. Loosen screw. Align the lugs (N) on the

guard with slots (O) on the gear case.

2. Push the guard down until the guard lug

engages and rotates freely in the groove

on the gear case hub.

3. Rotate guard (I) into desired working position. The guard body

should be positioned between the spindle and the operator to

provide maximum operator protection.

4. Tighten the screw to secure the guard on the gear case cover.

You should be unable to rotate the guard by hand. Do not

operate grinder with a loose guard.

5. To remove the guard, loosen screw, rotate the guard so that the

arrows are aligned and pull up on the guard.

OPERATION

Guards and Flanges

It is important to choose the correct guards and flanges to use with

the grinder accessories. See page 6 and this page for the correct

accessories.

NOTE: Edge grinding and cutting can be performed with Type 27

wheels designed and specified for this purpose.

WARNING: Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels and other acces-

sories running over rated accessory speed may burst and cause

injury. Every unthreaded accessory must have a 7/8" arbor hole. If

it does not, it may have been designed for a circular saw and

should not be used. Use only the accessories shown on pages 6–7.

Accessory ratings must be above listed minimum wheel speed as

shown on tool nameplate.

Switches

CAUTION: Hold the side handle and body of the tool firmly to

maintain control of the tool at start up and during use and until the

wheel or accessory stops rotating. Make sure the wheel has come

to a complete stop before laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the

tool on or off while under load conditions. Allow the grinder to run

up to full speed before touching the work surface. Lift the tool from

the surface before turning the tool off. Allow the tool to stop rotating

before putting it down.

PADDLE SWITCH (D28402, D28402N)

CAUTION: Before connecting the tool to a power source depress

and release the paddle switch (A) once [D28402: without depress-

ing the lock-on button (J)] to ensure that the switch is off. Depress

and release the paddle switch as described above after any inter-

ruption in power supply to the tool, such as the activation of a

ground fault interrupter, throwing of a circuit breaker, accidental

unplugging, or power failure. If the paddle switch is locked on, the

tool will start unexpectedly when it is reconnected.

To turn the tool on, push the

lock-off lever (B) toward the back of

the tool, then depress the paddle

switch (A). The tool will run while the

switch is depressed. Turn the tool off

by releasing the paddle switch.

WARNING: Do not disable the lock-off lever. If the lock-off lever

is disabled, the tool may start unexpectedly when it is laid down.

English

SLIDER SWITCH (D28110, D28112)

CAUTION: Before connecting the tool to a power supply, be sure

the switch is in the off position by pressing the rear part of the switch

and releasing. Ensure the switch is in the off position as described

above after any interruption in power supply to the tool, such as the

activation of a ground fault interrupter, throwing of a circuit breaker,

accidental unplugging, or power failure. If the switch is locked on

when the power is connected, the tool will start unexpectedly.

To start the tool, slide the ON/OFF

switch (L) toward the front of the tool.

To stop the tool, release the ON/OFF

switch.

For continuous operation, slide the

switch toward the front of the tool and

press the forward part of the switch

inward. To stop the tool while operat-

ing in continuous mode, press the rear

part of the switch and release.

LOCK-ON BUTTON (D28402)

The lock-on button (J) offers increased

comfort in extended use applications.

To lock the tool on, push the lock-off

lever (B) toward the back of the tool

then depress the paddle switch (A).

With the tool running, depress the lock-

on button (J). The tool will continue to

run after the paddle switch is released. To unlock the tool, depress

and release the paddle switch. This will cause the tool to stop.

CAUTION: Allow the tool to reach full speed before touching tool

to the work surface. Lift the tool from the work surface before turn-

ing the tool off.

SPINDLE LOCK

The spindle lock (C) is provided to prevent the spindle from rotat-

ing when installing or removing wheels. Operate the spindle lock

only when the tool is turned off, unplugged

from the power supply, and has come to a

complete stop. Do not engage the spindle

lock while the tool is operating because

damage to the tool will result. To engage the

lock, depress the spindle lock button and

rotate the spindle until you are unable to

rotate the spindle further.

Mounting and Using Depressed Center

Grinding Wheels and Sanding

Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, depress and release the

paddle switch to ensure that the tool is off.

Hubbed wheels install directly on the 5/8"-11 threaded spindle.

Thread of accessory must match thread of spindle.

1. Backing flange is retained to the grinder by an O-ring on the

spindle. Remove backing flange by pulling and twisting flange

away form the machine.

2. Thread the wheel on the spindle by hand.

3. Depress the spindle lock button and use a wrench to tighten the

hub of the wheel.

4. Reverse the above procedure to remove the wheel.

CAUTION: Failure to properly seat the wheel before turning the

tool on may result in damage to the tool or the wheel.

MOUNTING NON-HUBBED WHEELS

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, turn the switch on and off

as previously described to ensure that the tool is off.

English

Depressed center Type 27 grinding wheels

must be used with included flanges. See

page 6 of this manual for more information.

1. Install the unthreaded backing flange

(G) on spindle (D) with the raised section

(pilot) against the wheel. Be sure the

backing flange recess is seated onto the flats of the spindle by

pushing and twisting the flange before placing wheel.

2. Place wheel against the backing flange,

centering the wheel on the raised sec-

tion (pilot) of the backing flange.

3. While depressing the spindle lock but-

ton, thread the clamp nut (H) on spin-

dle. If the wheel you are installing is

more than 1/8" (3.31mm) thick, place

the threaded clamp nut on the spindle

so that the raised section (pilot) fits into

the center of the wheel. If the wheel you

are installing is 1/8" (3.31mm) thick or

less, place the threaded clamp nut on

the spindle so that the raised section

(pilot) is not against the wheel.

4. While depressing the spindle lock button,

tighten the clamp nut with a wrench.

5. To remove the wheel, depress the spin-

dle lock button and loosen the threaded

clamp nut with a wrench.

NOTE: If the wheel spins after the clamp nut

is tightened, check the orientation of the

threaded clamp nut. If a thin wheel is

installed with the pilot on the clamp nut

against the wheel, it will spin because the

height of the pilot prevents the clamp nut

from holding the wheel.

1/4" WHEELS

(6.35mm)

1/8" WHEELS

(3.31mm)

Backing Flange

Clamp Nut

Backing Flange

Clamp Nut

SURFACE GRINDING WITH GRINDING WHEELS

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to the work surface, allowing the tool

to operate at high speed. Grinding rate is greatest when the tool

operates at high speed.

3. Maintain a 20˚ to 30˚ angle between the

tool and work surface.

4. Continuously move the tool in a forward

and back motion to avoid creating

gouges in the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

EDGE GRINDING WITH GRINDING WHEELS

CAUTION: Wheels used for cutting and edge grinding may break

if they bend or twist while the tool is being used to do cut-off work or

deep grinding. To reduce the risk of serious injury, limit the use of

these wheels with a standard Type 27 guard

to shallow cutting and notching (less than

1/2" in depth). The open side of the guard

must be positioned away from the operator.

For deeper cutting with a Type 1 cut-off

wheel, use a closed, Type 1 guard. See

the chart on page 7 for more information.

Type 1 guards are available at extra cost

from your local dealer or authorized

service center.

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Apply minimum pressure to the work surface, allowing the tool

to operate at high speed. Grinding rate is greatest when the

tool operates at high speed.

20˚-30˚

English

3. Position yourself so that the open-underside of the wheel is

facing away from you.

4. Once a cut is begun and a notch is established in the work-

piece, do not change the angle of the cut. Changing the angle

will cause the wheel to bend and may cause wheel breakage.

Edge grinding wheels are not designed to withstand side pres-

sures caused by bending.

5. Remove the tool from the work surface before turning the tool

off. Allow the tool to stop rotating before laying it down.

WARNING: Do not use edge grinding/cutting wheels for surface

grinding applications because these wheels are not designed for

side pressures encountered with surface grinding. Wheel breakage

and injury may result

SURFACE FINISHING WITH SANDING FLAP DISCS

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to work surface, allowing the tool to

operate at high speed. Sanding rate is greatest when the tool

operates at high speed.

3. Maintain a 5˚ to 10˚ angle between

the tool and work surface.

4. Continuously move the tool in a

forward and back motion to avoid

creating gouges in the work

surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

MOUNTING SANDING BACKING PADS

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, turn the switch on and off

as previously described to ensure that the tool is off.

5˚-10˚

CAUTION: Proper guard must be reinstalled for grinding wheel,

sanding flap disc, wire brush or wire wheel applications after sand-

ing applications are complete.

1. Place or appropriately thread backing

pad (Q) on the spindle.

2. Place the sanding disc (R) on the

backing pad.

3. While depressing spindle lock, thread

clamp nut (H) on spindle, piloting the

raised hub on the clamp nut into the

center of sanding disc and backing

pad.

4. Tighten the clamp nut by hand. Then

depress the spindle lock button while

turning the sanding disc until the sanding disc and clamp nut

are snug.

5. To remove the wheel, grasp and turn the backing pad and

sanding pad while depressing the spindle lock button.

USING SANDING BACKING PADS

Choose the proper grit sandpaper for your application. Sandpaper

is available in various grits. Coarse grits yield faster material

removal rates and a rougher finish. Finer grits yield slower

material removal and a smoother finish.

Begin with coarse grit discs for fast, rough material removal.

Move to a medium grit paper and finish with a fine grit disc for

optimal finish.

Coarse 16 - 30 grit

Medium 36 - 80 grit

Fine Finishing 100 - 120 grit

Very Fine Finishing 150 - 180 grit

1. Allow the tool to reach full speed before touching tool to the

work surface.

English

2. Apply minimum pressure to work surface, allowing the tool to

operate at high speed. Sanding rate is greatest when the tool

operates at high speed.

3. Maintain a 5˚ to 15˚ angle between

the tool and work surface. The san-

ding disc should contact approxi-

mately one inch of work surface.

4. Move the tool constantly in a straight

line to prevent burning and swirling

of work surface. Allowing the tool to rest on the work surface

without moving, or moving the tool in a circular motion causes

burning and swirling marks on the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

Mounting and Using Wire Brushes

and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder

spindle without the use of flanges. Use only wire brushes or

wheels provided with a 5/8"-11 threaded hub. A Type 27 guard is

required when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes

and wheels. They can become sharp.

CAUTION: Wheel or brush must not touch guard when mounted

or while in use. Undetectable damage could occur to the accessory,

causing wires to fragment from accessory wheel or cup.

MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, turn the switch on and off

as previously described to ensure that the tool is off.

1. Thread the wheel on the spindle by hand.

5˚-15˚

2. Depress spindle lock button and use a wrench on the hub of the

wire wheel or brush to tighten the wheel.

3. To remove the wheel, reverse the above procedure.

CAUTION: Failure to properly seat the wheel hub before turning

the tool on may result in damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS

Wire wheels and brushes can be used for removing rust, scale and

paint, and for smoothing irregular surfaces.

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to work surface, allowing the tool to

operate at high speed. Material removal rate is greatest when

the tool operates at high speed.

3. Maintain a 5˚ to 10˚ angle between the

tool and work surface for wire cup

brushes.

4. Maintain contact between the edge of

the wheel and the work surface with

wire wheels.

5. Continuously move the tool in a forward

and back motion to avoid creating gouges in

the work surface. Allowing the tool to rest on

the work surface without moving, or moving

the tool in a circular motion causes burning

and swirling marks on the work surface.

6. Remove the tool from the work surface before turning the tool

off. Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a

sudden sharp movement of grinder may be experienced.

5˚-10˚

English

Mounting and Using Cutting

(Type 1) Wheels

Cutting wheels include diamond wheels and abrasive discs.

Abrasive cutting wheels for metal and concrete use are available.

Diamond blades for concrete cutting can also be used.

WARNING: A closed, 2-sided cutting wheel guard is not included

with this tool but is required when using cutting wheels. Failure to

use proper flange and guard can result in injury resulting from wheel

breakage and wheel contact. See page 7 for more information.

MOUNTING CLOSED (TYPE 1) GUARD

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, turn the switch on and off

as previously described to ensure that the tool is off.

1. Open the guard latch (M). Align

the lugs (N) on the guard with the

slots (O) on the gear case.

2. Push the guard down until the

guard lug engages and rotates

freely in the groove on the gear

case hub.

3. Rotate guard (I) into desired

working position. The guard body

should be positioned between the

spindle and the operator to provide

maximum operator protection.

4. Close the guard latch to secure the guard

on the gear case cover. You should be

unable to rotate the guard by hand when

the latch is in closed position. If rotation is

possible, tighten the adjusting screw (P) with clamp lever in the

closed position. Do not operate grinder with a loose guard or

clamp lever in open position.

5. To remove the guard, open the guard latch, rotate the guard so

that the arrows are aligned and pull up on the guard.

NOTE: If, after a period of time, the guard

becomes loose, tighten the adjusting

screw (P) with the clamp lever in the

closed position.

CAUTION: Do not tighten adjusting

screw with clamp lever in open position.

Undetectable damage to guard or

mounting hub may result.

MOUNTING CUTTING WHEELS

CAUTION: Turn off and unplug the tool before making any

adjustments or removing or installing attachments or acces-

sories. Before reconnecting the tool, turn the switch on and off

as previously described to ensure that the tool is off.

CAUTION: Matching diameter threaded backing flange and

clamp nut (included with tool) must be used for cutting wheels.

1. Place the unthreaded backing flange on spindle with the raised

section (pilot) facing up. The raised section (pilot) on the back-

ing flange will be against the wheel when the wheel is installed.

2. Place the wheel on the backing flange, centering the wheel on

the raised section (pilot).

3. Install the threaded clamp nut with the raised section (pilot)

facing away from the wheel.

4. Depress the spindle lock button and tighten clamp nut with

a wrench.

5. To remove the wheel, grasp and turn while depressing the

spindle lock button.

English

USING CUTTING WHEELS

WARNING: Do not use edge grinding/

cutting wheels for surface grinding applica-

tions because these wheels are not

designed for side pressures encountered

with surface grinding. Wheel breakage and

injury may result.

1. Allow tool to reach full speed before

touching tool to work surface.

2. Apply minimum pressure to work

surface, allowing tool to operate at

high speed. Cutting rate is greatest

when the tool operates at high speed.

3. Once a cut is begun and a notch is established in the work-

piece, do not change the angle of the cut. Changing the angle

will cause the wheel to bend and may cause wheel breakage.

4. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before setting it down.

MAINTENANCE

Cleaning

WARNING: Blowing dust and grit out of motor and switch actuator

using clean, dry compressed air is a necessary regular maintenance

procedure. Dust and grit containing metal particles often accumulate

on interior surfaces and could create an electrical shock or electrocu-

tion if not frequently cleaned out. It is recommended that a ground

fault circuit interrupter (GFCI) is utilized to further protect the user

from electric shock resulting from the accumulation of conductive

particles. If the tool is deactivated by the GFCI, unplug the tool and

check and clean the tool before resetting the GFCI. ALWAYS WEAR

SAFETY GLASSES when cleaning or using this tool.

CAUTION: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. Use a clean, dry

cloth only.

Lubrication

DEWALT tools are properly lubricated at the factory and are ready

for use.

Repairs

To assure product SAFETY and RELIABILITY, repairs, mainte-

nance and adjustments should be performed by a D

EWALT factory

service center, a D

EWALT authorized service center or other

qualified service personnel. Always use identical replacement

parts.

Accessories

Recommended accessories for use with your tool are available at

extra cost from your local dealer or authorized service center. If you

need assistance in locating any accessory, please contact D

EWALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,

call 1-800-4-D

EWALT (1-800-433-9258) or visit our website

www.dewalt.com.

CAUTION: The use of any other accessory not recommended

for use with this tool could be hazardous.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty mate-

rials or workmanship for three years from the date of purchase.

This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

English

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

EWALT Power Tool, Laser, or Nailer for any reason, you can

return it within 90 days from the date of purchase with a receipt for

a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country spe-

cific warranty information contained either in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

EWALT for a free

replacement.

Français

SI VOUS AVEZ DES QUESTIONS OU VOUS VOULEZ NOUS

FAIRE PART DE VOS COMMENTAIRES CONCERNANT CET

OUTIL OU TOUT AUTRE OUTIL D

EWALT, COMPOSEZ SANS

FRAIS LE : 1 800 433-9258. (1-800-4-DEWALT).

Règles de sécurité – Généralités

AVERTISSEMENT : Lire, comprendre et suivre

toutes les directives précisées ci-dessous, y com-

pris les consignes de sécurité, afin d’éviter les risques de

choc électrique, d’incendie ou de blessure grave.

CONSERVER CES DIRECTIVES

AIRE DE TRAVAIL

• L’aire de travail doit être propre et bien éclairée. Les établis

encombrés et les endroits sombres peuvent entraîner des acci-

dents.

• Ne pas faire fonctionner des outils électriques dans des

atmosphères explosives, comme en présence de liquides,

de gaz et de poussières inflammables. Les outils électriques

produisent des étincelles qui peuvent enflammer la poussière

ou les vapeurs

• Tenir les enfants, les visiteurs ou toute autre personne à

l’écart lorsqu’on utilise un outil électrique; les distractions

peuvent faire perdre la maîtrise de ce dernier.

MESURES DE SÉCURITÉ – ÉLECTRICITÉ

• Les outils mis à la terre doivent être branchés dans une

prise correctement installée et mise à la terre tel que

l’indiquent les codes et règlements en vigueur. Ne jamais

retirer la broche de mise à la terre ou modifier la prise en

aucune façon. Ne pas utiliser de fiche d’adaptation.

Consulter un électricien qualifié s’il y a un doute en ce qui

concerne la mise à la terre de la prise. En cas de défaillance

électrique ou de bris de l’outil, la mise à la terre procure un

chemin de faible résistance au courant afin de réduire les

risques de choc électrique. Cette protection ne s’applique

qu’aux outils de classe I (mis à la terre).

• Les outils à double isolation sont munis d’une fiche polar-

isée (c’est-à-dire que l’une des lames est plus large que

l’autre), laquelle ne peut être raccordée qu’à une prise

polarisée et ce, dans un seul sens; on doit l’inverser si on

est incapable de l’enfoncer complètement. Si la fiche ne

s’adapte toujours pas, on doit faire appel à un électricien

qualifié pour qu’il installe la prise appropriée. On ne doit

jamais modifier la fiche. La double isolation élimine

le besoin d’installer un cordon d’alimentation trifilaire et un

système d’alimentation électrique pourvus d’une mise à la terre;

seuls les outils de classe II (à double isolation) sont munis

d’une telle protection.

• Éviter tout contact entre le corps et les éléments mis à la

terre, comme les tuyaux, les radiateurs, les cuisinières et

les réfrigérateurs, afin de réduire les risques de choc

électrique.

• Ne pas utiliser l’outil électrique dans des endroits mouillés,

ni l’exposer à la pluie; l’infiltration d’eau à l’intérieur de l’outil

augmente les risques de choc électrique.

• Ne pas utiliser le cordon de manière abusive; on ne doit pas

transporter l’outil en le tenant par le cordon, ou utiliser ce

dernier pour le débrancher. On doit tenir le cordon à l’écart

des sources de chaleur, de l’huile, des bords tranchants

ou des pièces mobiles. Remplacer immédiatement les

cordons endommagés, car ces derniers augmentent les

risques de choc électrique.

• Lorsqu’on utilise un outil électrique à l’extérieur, on ne doit

utiliser que des rallonges conçues pour cet usage, comme

celles de type « W-A » ou « W », afin de réduire les risques de

choc électrique. S’assurer que la rallonge est en mesure de

porter le courant nécessaire à l’outil. Une rallonge de calibre

Français

inférieur entraînera une chute de tension se traduisant par une

perte de puissance et une surchauffe. Le tableau ci-dessous

illustre les calibres que l’on doit utiliser selon la longueur de la

rallonge et l’intensité nominale indiquée sur la plaque signalé-

tique. En cas de doute, utiliser le calibre suivant. Plus le calibre

est petit, plus la rallonge peut porter du courant.

Calibre minimal des cordons de rallonge

Tensi

on Longueur totale du cordon en meters

120 V De 0 à 7 De 7 à 15 De 15 à 30 De 30 à 45

240 V De 0 à 7 De 7 à 15 De 15 à 39 De 30 à 45

Intensité (A)

Au Au Calibre moyen de fil

moins plus

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Non recommandé

SÉCURITÉ PERSONNELLE

• Rester vigilant en tout temps et faire preuve de jugement

lorsqu’on utilise un outil électrique. Ne pas utiliser l’outil

lorsqu’on est fatigué ou sous l’influence de drogues,

d’alcool ou de médicaments, car un moment d’inattention

pourrait entraîner des blessures graves.

• Porter des vêtements appropriés. Ne pas porter des vête-

ments amples ou des bijoux. Couvrir ou attacher les

cheveux longs. Garder les cheveux, les vêtements, les

bijoux et les gants éloignés des pièces mobiles, car ceux-ci

peuvent s’y coincer. Se tenir éloigné des évents puisque ces

derniers pourraient camoufler des pièces mobiles.

• Éviter les démarrages accidentels; s’assurer que l’interrup-

teur est en position d’arrêt avant de brancher l’outil. Ne pas

transporter l’outil en laissant le doigt sur l’interrupteur ni le

brancher lorsque l’interrupteur est en position de marche, car

cela pourrait causer un accident.

• Retirer les clés de réglage avant de démarrer l’outil. Une clé

laissée sur une pièce rotative pourrait entraîner des blessures.

• Ne pas trop étendre les bras. Les pieds doivent rester

ancrés fermement au sol afin de maintenir son équilibre en

tout temps et de mieux maîtriser l’outil dans des situations

imprévues.

• Utiliser le matériel de sécurité approprié; toujours porter

des lunettes de protection. Porter un masque anti-poussières,

des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert.

UTILISATION ET ENTRETIEN DE L’OUTIL

• Fixer et soutenir la pièce sur une plate-forme stable au

moyen d’une bride de serrage ou de tout autre dispositif

semblable. La pièce est instable lorsqu’on la retient

manuellement ou qu’on l’appuie contre le corps, ce qui pourrait

faire perdre la maîtrise de l’outil.

• Ne pas forcer l’outil ni l’utiliser pour des travaux autres que

ceux pour lesquels il a été conçu. Pour obtenir de meilleurs

résultats et prévenir les risques de blessure, laisser l’outil

couper à la vitesse pour laquelle il a été conçu.

• Ne pas utiliser l’outil lorsque l’interrupteur marche-arrêt ne

fonctionne pas. Tout outil qui ne peut être commandé au

moyen de l’interrupteur est dangereux et doit être réparé.

• Débrancher l’outil de la source d’alimentation électrique

avant d’effectuer un réglage, de changer les accessoires ou

de ranger l’outil; ces mesures de sécurité préventives

réduisent les risques de démarrage accidentel.

• Lorsqu’on n’utilise pas l’outil, le ranger hors de la portée

des enfants ou des personnes non qualifiées. Les outils sont

dangereux entre les mains de personnes inexpérimentées.

• Bien entretenir l’outil; s’assurer qu’il est toujours bien

propre et aiguisé. Les outils bien entretenus et dont les bords

sont bien tranchants sont moins susceptibles de rester coincés

et sont plus faciles à maîtriser.

Français

• Vérifier les pièces mobiles afin de s’assurer qu’elles sont

bien alignées et qu’elles ne restent pas coincées. Vérifier

également les pièces afin de s’assurer qu’il n’y a aucun

bris ni aucune autre condition susceptible de nuire au bon

fonctionnement de l’outil. Faire réparer l’outil si ce dernier

est endommagé avant de s’en servir à nouveau, car les

accidents sont souvent causés par des outils mal entretenus.

• N’utiliser que les accessoires recommandés par le fabricant

pour le modèle concerné. Un accessoire destiné à un outil

particulier peut devenir dangereux lorsqu’il est utilisé avec un

autre.

ENTRETIEN

• L’outil doit être entretenu par le personnel qualifié seule-

ment; toute maintenance effectuée par une personne non

qualifiée pourrait entraîner des risques de blessure.

• Lors de l’entretien, n’utiliser que des pièces de rechange

identiques et suivre les directives précisées à la section

« Entretien » du présent guide afin de prévenir les risques de

choc électrique ou de blessure.

Directives de sécurité supplémentaires

pour meuleuses

• S'assurer que la bride tournante sur collet battu de la meule est

dotée d'une rondelle (S) en caoutchouc jaune (Fig. 1).

Remplacer la rondelle si elle est manquante, endommagée ou

usée. Se reporter à la page 26 pour obtenir de l'information

détaillée sur l'installation de l'accessoire approprié.

AVERTISSEMENT : La meule ou l'accessoire peut se desser-

rer durant le ralentissement de l'outil mis à l'arrêt si la rondelle

de caoutchouc est manquante ou endommagée. Si la meule ou

l'accessoire se desserre, l'un ou l'autre peut sortir de la machine et

causer des blessures graves.

• Toujours utiliser un dispositif de protection adéquat avec

une meule. Le dispositif de protection protège l’opérateur con-

tre les fragments de meule et empêche tout contact avec la

meule.

• Les accessoires doivent être classés au moins pour la

vitesse recommandée indiquée sur l’étiquette d’avertisse-

ment de l’outil. Les meules et tout autre accessoire fonction-

nant à une vitesse supérieure à la vitesse nominale risquent

d’être projetés et de causer des blessures. Les caractéristiques

nominales des accessoires doivent être supérieures à la vitesse

minimale indiquée sur la plaque signalétique de l’outil.

• Tenez l’outil par sa surface de prise isolée dans une situa-

tion où l’outil de coupe peut entrer en contact avec un

câblage caché ou avec son propre cordon d’alimentation.

Tout contact avec un fil « sous tension » mettra « sous tension »

les pièces métalliques de l’outil et l’opérateur recevra une

décharge électrique.

• Ne pas utiliser les meules de type 11 (boisseau conique) sur

cet outil. Ne pas utiliser les bons accessoires peut entraîner des

blessures.

• TOUJOURS PORTER UNE PROTECTION OCULAIRE POUR

UTILISER CET OUTIL.

• Il n’est pas recommandé d’utiliser des accessoires non

indiqués dans le présent mode d’emploi; cela peut être

dangereux. Utiliser des amplificateurs de puissance qui

feraient fonctionner l’outil à une vitesse supérieure à sa

vitesse nominale représente une utilisation abusive.

• Ne pas utiliser de lames de scies circulaires ou toute autre

lame dentée avec cet outil. Il peut en résulter des blessures

graves.

• Au démarrage de l’outil, pourvu d’une meule neuve ou de

rechange ou d’une brosse métallique neuve ou de

rechange, le tenir dans un endroit bien protégé et le laisser

Français

tourner pendant une minute. Si la meule présente une fissure

ou un défaut non détecté, elle éclatera en moins d’une minute.

Si la brosse métallique présente des broches métalliques mal

fixées, les broches seront détectées. Ne jamais démarrer l’outil

si une personne se trouve dans la trajectoire de la meule, y

compris l’opérateur.

• Éviter de faire rebondir la meule ou de la traiter durement.

Si cela se produit, arrêter l’outil et inspecter la meule à la

recherche de fissures ou de défauts.

• Diriger les étincelles loin de l’opérateur, des personnes

présentes et de toute matière inflammable. Des étincelles

peuvent se produire durant la coupe ou le meulage. Les étin-

celles peuvent causer des brûlures ou provoquer un incendie.

• Toujours utiliser la poignée latérale. Serrer solidement la

poignée. La poignée latérale doit toujours être utilisée afin de

garder la maîtrise de l’outil en tout temps.

• Ne jamais couper à un endroit pouvant contenir un câblage

électrique ou des tuyaux. Il peut en résulter des blessures

graves.

• Nettoyer souvent l’outil, surtout après un usage intensif. La

poussière et la saleté contenant des particules métalliques s’ac-

cumulent souvent sur les surfaces internes et peuvent présen-

ter un risque de choc électrique.

• Ne pas faire fonctionner cet outil durant de longues péri-

odes. Les vibrations causées par le fonctionnement de l’outil

peuvent provoquer des blessures permanentes aux doigts, aux

mains et aux bras. Utiliser des gants afin d’amortir davantage les

vibrations, s’arrêter fréquemment et limiter l’utilisation quotidi-

enne de l’outil.

• Diriger le dispositif d’évacuation des poussières loin de

l’opérateur et des collègues. Il peut en résulter des blessures

graves (fig. 1, K).

• L’étiquette apposée sur l’outil peut afficher les symboles

suivants. Ces symboles et leurs définitions sont les suivants :

V ............volts A..............ampères

Hz ..........hertz W ............watts

min ........minutes ..........courant alternatif

......courant continu n

............aucune option à vide

..........construction de ............symbole

..............classe II ................d’avertissement

…/min ....tours par minute ............borne de terre

Causes de l’effet de rebond et

prévention de l’opérateur

• L’effet de rebond est la réaction soudaine d’une meule, d’une

brosse métallique ou d’un disque à lamelle pincé, coincé ou mal

aligné, c’est-à-dire une perte de maîtrise de l’outil de tronçon-

nage qui est soulevé hors de la pièce, vers l’opérateur.

• Lorsque la meule est pincée ou très coincée par la pièce, la

meule bloque et le moteur réagit en entraînant rapidement la

meule vers l’opérateur ou loin de ce dernier.

• L’effet de rebond résulte d’une utilisation abusive de l’outil et/ou

de mauvaises procédures d’utilisation ou conditions. Cela peut

être évité par la prise de précautions adéquates comme celles

indiquées ci-après :

• Tenir fermement l’outil à deux mains, puis positionner le

corps et les bras de manière à résister aux forces de

l’effet de rebond. Les forces de l’effet de rebond peuvent

être maîtrisées par l’opérateur si les précautions adéquates

sont prises.

• Si la meule se coince ou si la coupe est interrompue

pour quelque raison que ce soit, relâcher la gâchette et

tenir l’outil immobile dans le matériau jusqu’à ce que la

meule s’arrête complètement. Ne jamais tenter d’enlever

l’outil de la pièce ou de tirer sur l’outil lorsque la meule

La page charge ...

DeWalt D28402B Manuel utilisateur

Marque: DeWalt

Modèle: D28402B

Catégorie: Meuleuses d'angle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt D28402B User manual
español: DeWalt D28402B Manual de usuario

Documents connexes

Autres documents

Epson D28114 Manuel utilisateur