2. Sentiotec
  3. ALASKA CORNER INFRA+

Sentiotec ALASKA CORNER INFRA+ Manuel utilisateur

  • Bonjour ! Je suis un chatbot IA spécialement formé pour vous aider avec le Sentiotec ALASKA CORNER INFRA+ Manuel utilisateur. J’ai déjà parcouru le document et peux vous fournir des réponses claires et précises.
ALASKA-C-IR+
Version 03/21 item no. 1-030-267
EN
DE
FR
IT
PL
PT
INSTRUCTIONS FOR INSTALLATION
English
Solid wood sauna
ALASKA
CORNER INFRA+
206 x 206 x 204 cm
Table of Contents
1. Preparing for installation 3
1.1. Tools required 4
1.2. Maintenance and cleaning 5
1.3. Disposal 5
1.4. ALASKA CORNER INFRA+ parts list 6
2. Cabin installation 9
2.1. Base frame installation 9
2.2. Wall element assembly 10
2.3. Ceiling installation 18
2.4. Ventilation slit installation 20
2.5. Installinginteriorttings 20
2.6. Installing accessories 27
2.7. Installing glass door 29
2.8. Installing roof trim 31
2.9. Installing ceiling cover slat 32
3. Floor plan 33
3.1. Leftoorplan 33
3.2. Rightoorplan 34
3.3. Changesfortherightoorplaninstallation 35
EN
Instructions for installation p. 3/36
1. Preparing for installation
Read these installation instructions carefully and keep them within reach when
using the sauna so that you can look up product information at any time.
Important note:
●Before you begin work, check the parts list to ensure that all the individual
parts have been delivered. If you discover any missing parts, notify your
dealer within 14 days of receiving the sauna cabin.
●The room that the sauna is installed in must be dry and ensure an appropriate
amount of air circulation.
● Theoormustbelevelandeven,preferablyastoneortiledoor.
●A minimum room height of 230 cm is required for the cabin installation work.
●A distance of at least 5 cm from the wall must be maintained.
●The inside of the wooden parts used must not be handled with any impreg-
nating material.
●You need an assistant for the installation.
●Wood is a natural product that can swell, shrink or warp, despite good stor-
age. For this reason, some force may be necessary during the installation.
● Allscrewttingsmustbepre-drilled.
Attention!
The electrical connection may only be performed by a qualied electrician
or similarly qualied person.
These installation instructions can also be found in the downloads section
of our website: www.sentiotec.com/downloads.
Instructions for installation p. 4/36
1.1. Tools required
●Hammer with a wooden head or a mallet
●Cordless screwdriver with bits for cross-head screws and Torx
●Roller tape measure
●Drill bits with a diameter of 3 mm, 10 mm, 20 - 30 mm (for sauna heater
power cable)
●Spirit level
●1.5 mm hexagonal socket wrench
●Utility knife
●Ladder
●Backsaw
This symbol indicates tips and useful information
Pre-drill
Cut to real measurement with backsaw
60 cm
80 cm
100 cm
Check the right angle:
Handle glass with care: Special care must be taken with the edges of
the glass – hardened glass can shatter into small pieces in the event of
impact. Insert protective cushioning (e.g: cardboard box) under the edge
of the glass.
EN
Instructions for installation p. 5/36
1.2. Maintenance and cleaning
●The sauna should be cleaned with a damp cloth. Only use warm water – no
cleaning products.
●We recommend heating the cabin once a month if the sauna is not used for
a long time.
Pitch pockets are not grounds for return, since they can always appear in
spruce wood and the depth at which they lie cannot be detected during
the sorting-out process.
If these are just under the surface, heat can cause them to soften and
“bleed”.
The leaking pitch can be removed with a rag soaked in acetone. If only
droplets of pitch occur, allow these to harden and then carefully scrape
themowithaknife.
1.3. Disposal
●Please dispose of packaging materials in accordance with the appli-
cable disposal regulations.
●Used units contain reusable materials as well as hazardous substanc-
es. Therefore, do not dispose of your used unit with household waste,
but rather do so in accordance with the locally applicable regulations.
Instructions for installation p. 6/36
Base frame
2 Base frame 204 x 9 x 4 cm
1 Base frame 138 x 9 x 4 cm
1 Base frame 61.2 x 9 x 4 cm
Wall elements
3 A/B wall elements with Multiclip 193 x 48 x 4 cm
1 A/B wall element 193 x 48 x 4 cm
1 A/A electrical element with Multiclip 193 x 44 x 4 cm
1 A/A wall element with Multiclip 193 x 44 x 4 cm
1 A/A wall element 193 x 44 x 4 cm
1 A/A wall element with Multiclip 193 x 55.2 x 4 cm
1 A/B ventilation element with Multiclip 193 x 48 x 4 cm
2 A/B wall elements with heater recess 193 x 48 x 4 cm
1 A/B wall element with “Infracontrol mini” recess 193 x 48 x 4 cm
1 Element above the door 69.3 x 10.1 x 4 cm
1 Element above the glass element 72.3 x 8.6 x 4 cm
Ceiling elements
2 A/B ceiling elements 194 x 48 x 4 cm
1 A/B ceiling element 194 x 49 x 4 cm
1 A/A ceiling element, diagonal 186 x 49 x 4 cm
Corner posts
3 90° corner posts with Multiclip 193 x 6 x 6 cm
1 45° corner posts next to door with Multiclip 202 x 7.8 x 4 cm
1 45° corner posts next to door with groove 202 x 7.8 x 4 cm
1
Post for glass element, 8 mm groove and Multiclip
202 x 4.5 x 4 cm
No. of
items Name Dimensions
1.4. ALASKA CORNER INFRA+ parts list
EN
Instructions for installation p. 7/36
Support slats
1 Roof support slat 197 x 4 x 4 cm
1 Roof support slat 193 x 4 x 4 cm
2 Roof support slat 1 x 45° 141.6 x 4 x 4 cm
1 Roof support slats 2 x 45° 89.7 x 4 x 4 cm
1 Roof support slat 196 x 1.2 x 4 cm
1 Roof support slat 192 x 1.2 x 4 cm
2 Roof support slat 1 x 22.5° 141.2 x 1.2 x 4 cm
1 Roof support slat 1 x 22.5° 83.2 x 1.2 x 4 cm
1 Bench support slat 1 x 45° 142.3 x 4 x 4 cm
1 Bench support slat 120 x 4 x 4 cm
3 Bench support slats 58 x 4 x 4 cm
2 Mounting slats for bench screen 26 x 4 x 4 cm
Interior ttings
1 Bench 195 x 62 x 9 cm
1 Bench with adjustable backrest 195 x 62 x 9 cm
1 Bench 133.5 x 62 x 9 cm
1 Bench cover slat 72.3 x 14 x 2 cm
2 Backrests 101 x 26 x 5 cm
2 Backrests 53 x 26 x 5 cm
1 Bench screen 195 x 35 x 5 cm
1 Heater safety guard, 3 parts 57 x 475 x 75 cm
1 item 57 x 75 cm, 2 items 45.5 x 55 cm
1 Floor grid 70 x 53 x 4 cm
2 Headrests 43 x 25 x 7 cm
1 Lamp protection grille 38 x 32 x 4 cm
1 Ventilation slit 52 x 14 x 1.5 cm
No. of
items Name Dimensions
Instructions for installation p. 8/36
Glass elements
1 Glass door 191.5 x 68 x 0.8 cm
1 Glass element 194.5 x 75.5 x 0.8 cm
Roof trim slats
2 Roof trim slat 1 x 22.5° 149.8 x 6 x 4 cm
1 Roof trim slat 1 x 22.5° 86.5 x 6 x 4 cm
Accessories
1Ualuminiumprole 72.3 x 1.2 x 1.5 cm
1 Door handle set wood/stainless steel
1 2 door hinges 8653-02
1 Door magnet, sleeve plate
1 Sauna lamp
2 Infrared radiator ECO-350-R 1-027-785
2 Prestige radiator covers 71 x 21 x 5 cm
1 Infrabox basic Set 1-035-705
1 Cable WC4-GST-C05 1-028-862
1 Distributor IR-1P2 1-028-731
1 Template for Multiclip installation
1 3 Silicon cables: 5 x 2.5 mm2
1 3 Silicon cables: 3 x 1.5 mm2
1 Installation material set
1 Installation instructions
No. of
items Name Dimensions
EN
Instructions for installation p. 9/36
2. Cabin installation
Thecabincanhavearightorleftset-up;pleasenotethecorrespondingoor
plans on page 33 and page 34.
2.1. Base frame installation
Left oor plan
Right oor plan
204 cm
61.2 cm
138 cm
204 cm
138 cm
204 cm
204 cm
61.2 cm
3 mm drill bit, 3 screws 4 x 70 mm
3 mm drill bit, 3 screws 4 x 70 mm
Instructions for installation p. 10/36
2.2. Wall element assembly
The corner posts are connected to the wall elements using Multiclips. The other
wall elements are connected tongue and groove and are screwed together.
Left oor plan
*
*
* *
*
*
* Multiclips
Attention!
Theinstallationsubsequentlydescribedisfortheleftoorplan.Forchanges
aectingtheinstallationfortherightoorplan,seepage34.
* *
A always refers to the visible side. This is labelled on the top side of the
wall elements.
EN
Instructions for installation p. 11/36
Pre-assemblethewallelementswiththecornerpostsontheoorand
then place these posts on the base frame.
Insert the corner post from above down onto the wall elements. When doing this,
ensure that the Multiclips are correctly aligned (see below). The corner post must
beushwiththewallelements.
Multiclip
Installing corner posts with wall elements
Instructions for installation p. 12/36
Installing wall elements
Electrical element
The electrical element has drill holes for laying cables. For the position
seeoorplansonpage33andpage34.
EN
Instructions for installation p. 13/36
Screwing wall elements together
3 mm drill bit, 8 screws 4 x 70 mm
Check the right angle before screwing the wall elements together.
Observe the tip on page 4.
Instructions for installation p. 14/36
Corner post and post for glass
EN
Instructions for installation p. 15/36
Glass element
3 mm drill bit,
1 screw 4 x 70 mm
3 mm drill bit,
1 screw 4 x 70 mm
Instructions for installation p. 16/36
Element above the door
3 mm drill bit,
1 screw 4 x 70 mm
3 mm drill bit,
1 screw 4 x 70 mm
EN
Instructions for installation p. 17/36
Instructions for installation p. 18/36
2.3. Ceiling installation
Roof support slats
4 cm
Screws 4 x 70 mm
EN
Instructions for installation p. 19/36
Ceiling elements
3 mm drill bit, 19 screws 4 x 70 mm
1 cm
1 cm
17 screws 4 x 70 mm
49 cm
48 cm
48 cm 49 cm
Instructions for installation p. 20/36
2.4. Ventilation slit installation
2.5. Installing interior ttings
Bench support slats
2 screws 4 x 60 mm
3 mm drill bit, 3 screws 5 x 70 mm
3 mm drill bit, 4 screws 3 x 40 mm
82 cm
/