Sentiotec Alaska Mini Infra+ Manuel utilisateur

Taper
Manuel utilisateur
ALASKA-MN
Version 04/22 item no. 1-030-245
EN
DE
FR
IT
PL
PT
INSTRUCTIONS FOR INSTALLATION AND USE
English
Solid wood sauna
ALASKA
MINI INFRA+
160 x 110 x 204 cm
Table of Contents
1. Preparing for installation 3
1.1. Important note: 3
1.2. Tools required 4
1.3. Maintenance and cleaning 5
1.4. Disposal 5
1.5. ALASKA MINI INFRA+ parts list 6
2. Cabin installation 8
2.1. Base frame installation 8
2.2. Wall element installation 9
2.3. Ceiling installation 16
2.4. Ventilation slit installation 18
2.5. Installinginteriorttings 18
2.6. Installing accessories 24
2.7. Installing glass door 26
2.8. Installing roof trim 28
2.9. Installing ceiling cover slat 29
3. Floor plan 30
3.1. Rightoorplan 30
3.2. Leftoorplan 31
3.3. Changestotheleftoorplaninstallation 32
EN
Instructions for installation and use p. 3/32
1. Preparing for installation
Read these installation instructions carefully and keep them within reach when
using the sauna, so that you can look up product information at any time.
Attention!
The electrical connection may only be performed by a qualied electrician
or similarly trained person.
These installation instructions can also be found in the downloads section
of our website: www.sentiotec.com/downloads.
1.1. Important note:
Before you begin work, check the parts list to ensure that all the individual
parts have been delivered. If you discover any missing parts, notify your
dealer within 14 days of receiving the sauna cabin.
The room that the sauna is installed in must be dry and ensure an appropriate
amount of air circulation.
● Theoormustbelevelandeven,preferablyastoneortiledoor.
A minimum room height of 230 cm is required for the cabin installation work.
A distance of at least 5 cm from the wall must be maintained.
The inside of the wooden parts used must not be treated with any impreg-
nating material.
You need an assistant for the installation.
Wood is a natural product that can swell, shrink or warp, despite good stor-
age. For this reason, some force may be necessary during the installation.
● Allscrewttingsmustbepre-drilled.
Instructions for installation and use p. 4/32
This symbol indicates tips and useful information
Pre-drill
Cut to real measurement with backsaw
60 cm
80 cm
100 cm
Check the right angle:
Handle glass with care: Special care must be taken with the edges of
the glass – hardened glass can shatter into small pieces in the event of
impact. Insert protective cushioning (e.g: cardboard box) under the edge
of the glass.
1.2. Tools required
Hammer with a wooden head or a mallet
Cordless screwdriver with bits for cross-head screws and Torx
Roller tape measure
Drill bits with a diameter of 3 mm, 10 mm, 20 - 30 mm
(for sauna heater power cable)
Spirit level
1.5 mm hexagonal socket wrench
Utility knife
Ladder
Backsaw
EN
Instructions for installation and use p. 5/32
1.3. Maintenance and cleaning
The sauna should be cleaned with a damp cloth. Only use warm water – no
cleaning products.
We recommend heating the cabin once a month if the sauna is not used for
a long time.
Pitch pockets are not grounds for return, since they can always appear in
spruce wood and the depth at which they lie cannot be detected during
the sorting-out process.
If these are just under the surface, heat can cause them to soften and
“bleed”.
The leaking pitch can be removed with a rag soaked in acetone. If only
droplets of pitch occur, allow these to harden and then carefully scrape
themowithaknife.
1.4. Disposal
Please dispose of packaging materials in accordance with the appli-
cable disposal regulations.
Used units contain reusable materials as well as hazardous substanc-
es. Therefore, do not dispose of your used unit with household waste,
but rather do so in accordance with the locally applicable regulations.
Instructions for installation and use p. 6/32
Base frame
1 Base frame 156 x 9 x 4 cm
1 Base frame 108 x 9 x 4 cm
1 Base frame 102 x 9 x 4 cm
1 Base frame 64 x 9 x 4 cm
Wall elements
1 A/B wall element with radiator recess 193 x 48 x 4 cm
1 A/B wall element with Multiclip 193 x 48 x 4 cm
1 A/B ventilation element with Multiclip 193 x 48 x 4 cm
4 A/A wall elements with Multiclip 193 x 48 x 4 cm
1 A/A electrical element with Multiclip 193 x 58 x 4 cm
1Elementabovedoor,oorplan(right) 81.5 x 10.1 x 4 cm
1Elementabovedoor,oorplan(left) 81.5 x 10.1 x 4 cm
Ceiling elements
2 Ceiling elements 146 x 49 x 4 cm
Corner posts
3 90° corner posts with Multiclip 193 x 6 x 6 cm
1
Corner post with front hinge for glass door with Multiclip
202 x 6 x 7.5 cm
1 Post for glass element, 8 mm groove 202 x 4.5 x 4 cm
Support slats
2 Roof support slats 140 x 4 x 4 cm
2 Roof support slats 100 x 4 x 4 cm
2 Roof cover slats 144 x 1.2 x 4 cm
2 Roof cover slats 104 x 1.2 x 4 cm
2 Bench support slats 58 x 4 x 4 cm
2 Mounting slats for bench screen 26 x 4 x 4 cm
No. of items Name Dimensions
1.5. ALASKA MINI INFRA+ parts list
EN
Instructions for installation and use p. 7/32
No. of items Name Dimensions
Interior ttings
1 Bench 147 x 62 x 9 cm
1 Foot step panel 80 x 35 x 9 cm
2 Foot step feet 43 x 33 x 4 cm
2 Foot step struts, 2 x 45° diagonal 49.5 x 8 x 2 cm
2 Backrests 58 x 25.5 x 4 cm
1 Bench screen 147 x 34 x 4 cm
1 Heater protection grille – lime wood 62.5 x 8 x 2 cm
1 Heater protection grille – lime wood 37.5 x 8 x 2 cm
3 Mounting slats for heater protection grille – spruce 7 x 2.5 x 2.5 cm
1 Headrest 43 x 25 x 7 cm
1 Lamp protection grille 38 x 32 x 4 cm
1 Ventilation slit 52 x 14 x 1.5 cm
Glass elements
1 Glass door
191.5 x 59 x 0.8 cm
1 Glass element
194.5 x 22.4 x 0.8 cm
Roof rim slats
1 Roof rim slat 160 x 6 x 4 cm
2 Roof rim slats 115 x 6 x 4 cm
Accessories
1Ualuminiumprole
21.1 x 1.2 x 1.5 cm
1 Door handle set wood/stainless steel
1 2 door hinges 8653-02
1 Door magnet, sleeve plate
1 Sauna lamp
1 Infrared radiator ECO-350-R 1-027-785
1 Prestige radiator cover 71 x 21 x 5 cm
1 Infrabox basic Set 1-035-705
1 Cabel WC4-GST-C05 1-028-862
1 Distributor IR-1P2 1-028-731
1 Template for Multiclip installation
1 3 Silicon cables: 5 x 2.5 mm²
1 3 Silicon cables: 3 x 1.5 mm²
1 Installation material set
1 Installation instructions
Instructions for installation and use p. 8/32
2. Cabin installation
Thecabincanhavearightorleftsetup,pleasenotethecorrespondingoor
plans on Page 30 and Page 31.
2.1. Base frame installation
Right oor plan
Left oor plan
156 cm
64 cm
102 cm
108 cm
102 cm
108 cm
156 cm
64 cm
3 mm drill bit, 3 screws 4 x 70 mm
EN
Instructions for installation and use p. 9/32
2.2. Wall element installation
The corner posts are connected to the wall elements using Multiclips. The other
wall elements are connected by tongue and groove and are screwed together.
Right oor plan
*
*
* *
*
*
* Multiclips
Attention!
Theinstallationsubsequentlydescribedisfortherightoorplan.
ForchangesaectinginstallationfortheleftoorplanseePage32.
* *
A always refers to the visible side. This is labelled on the top side of the
wall elements.
Instructions for installation and use p. 10/32
Pre-assemblethewallelementswiththecornerpostsontheoorand
then place these posts on the base frame.
Insert the corner post on the wall elements, moving it downwards. When doing
this, ensure that the Multiclips are correctly aligned (see below). The corner post
mustbeushwiththewallelements.
Multiclip
Installing corner posts with wall elements
EN
Instructions for installation and use p. 11/32
Installing wall elements
Electrical element
The electrical element has drill holes for laying cables. For the position,
seeoorplansonPage30andPage31.
Instructions for installation and use p. 12/32
Screwing wall elements together
3 mm drill bit, 4 screws 4 x 70 mm
Check the right angle before screwing the wall elements together.
Observe the tip on page 4.
EN
Instructions for installation and use p. 13/32
Corner post and post for glass
Instructions for installation and use p. 14/32
Glass element
Element above the door
Selecttheelementfortherightoorplan
EN
Instructions for installation and use p. 15/32
3 mm drill bit, 2 screws 4 x 70 mm
Instructions for installation and use p. 16/32
2.3. Ceiling installation
Roof support slats
4 cm
3 mm drill bit, 12 screws 4 x 70 mm
EN
Instructions for installation and use p. 17/32
Ceiling elements
3 mm drill bit, 10 screws 4 x 70 mm
1 cm
1 cm
Instructions for installation and use p. 18/32
2.4. Ventilation slit installation
2.5. Installing interior ttings
Bench support slats
2 screws 4 x 60 mm
3 mm drill bit, 3 screws 5 x 70 mm
3 mm drill bit, 4 screws 3 x 40 mm
82 cm
EN
Instructions for installation and use p. 19/32
3 mm drill bit, 3 screws 5 x 70 mm
Screws 4 x 60 mm
Instructions for installation and use p. 20/32
Bench screen
4 screws 4 x 60 mm
1 cm
Bench
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196

Sentiotec Alaska Mini Infra+ Manuel utilisateur

Taper
Manuel utilisateur