Mouvex 1401-W00 Direct Drive Package LS-DDNC Installation Operation Manual

LS-DDNC

Instructions for application

DIRECT DRIVE PACKAGE

MISTRAL - B600 - TYPHON II

INSTRUCTIONS 1401-W00 e

Section 1401

Effective April 2023

Replaces April 2020

INSTALLATION

OPERATION

MAINTENANCE

SAFETY

STORAGE

Original instructions

This Instruction only contains direct drive package information. It is imperative to have in complement the

compressor one and also all the others relatives to the accessories, also the parts list before installing the

equipment.

Your distributor :

Z.I. La Plaine des Isles - F 89000 AUXERRE - FRANCE

Tel. : +33 (0)3.86.49.86.30 - Fax : +33 (0)3.86.49.87.17

contact.mouvex@psgdover.com - www.mouvex.com

EC CERTIFICATE OF CONFORMITY :

The EC Certificate of Conformity (paper version) is systematically attached to the equipment when shipped.

WARRANTY :

LSDDNC packages (except the compressor : see compressor Instructions) are covered 24 months by warranty within the limits mentioned

in our General Sales Conditions. In case of a use other than that mentioned in the Instructions manual, and without preliminary agreement

of MOUVEX, warranty will be canceled.

Warranty extension with oil BSC3 : See § WARRANTY.

2/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

MOUVEX TRUCK SCREW COMPRESSOR

SAFETY, STORAGE, INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

MODELS : LS-DDNC

DIRECT DRIVE PACKAGE

MISTRAL - B600 - TYPHON II

REMARKS :

MOUVEX truck screw-type compressors MUST be installed in sys-

tems designed by qualified personnel. The installation MUST be in

compliance with local standards, national regulations and rules of

safety.

This package is designed to be used on paved roads. Unless,

it is necessary to move towards a package DDK to achieve a

strengthened and adapted to the situation set.

This manual is designed to permit installation and commis-

sioning of MOUVEX truck screw-type compressors and MUST

accompany the compressor.

Maintenance of MOUVEX screw-type compressors must ONLY be

carried out by qualified technicians. This maintenance must meet

local and national standards as well as all safety regulations.

Read this manual, including all instructions and warnings, in

full BEFORE any use of MOUVEX compressors.

Reading and the removal of the labels on the package apply to

approval.

1. OVERALL DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.1 Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2 Mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3 At succion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4 Safety valve / Check relief . . . . . . . . . . . . . . . . . . . . . 11

2.5 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.6 Instrumentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.7 Chair modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3. USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Maintenance schedules . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Air filter replacement procedure . . . . . . . . . . . . . . . . . 13

4.3 Cartridge replacement procedure . . . . . . . . . . . . . . . . 13

4.4 Drive train inspection . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.5 Check and relief valve inspection . . . . . . . . . . . . . . . . 13

5. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6. WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6.1 Warranty claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6.2 24-months warranty extension with BSC3 oil . . . . . . . 15

7. STORAGE CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . 15

7.1 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

7.2 BSC oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8. SCRAPPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

9. COMPRESSORS FORM INFORMATION . . . . . . . . . . . . . 16

TABLE OF CONTENTS Page

ADDITIONAL DOCUMENTATION

The table below gives the list of instructions in addition

to this application instruction :

LS-DDNC

application Instructions Parts list

B600 20R/30R NT 1401-K00 PL 1401-K01

PL 1401-W01

B600 13R/15L

B600 19R/22L NT 1401-K00

PL 1401-K01

PL 1401-Q01

PL 1401-W01

MISTRAL 20R/30R NT 1401-J00 PL 1401-J01

PL 1401-W01

MISTRAL 13R/15L

MISTRAL 19R/22L NT 1401-J00

PL 1401-J01

PL 1401-Q01

PL 1401-W01

TYPHON II 20R/30R NT 1401-G00 PL 1401-G01

PL 1401-W01

TYPHON II 13R/15L

TYPHON II 19R/22L NT 1401-G00

PL 1401-G01

PL 1401-Q01

PL 1401-W01

Torque limiter NT 1401-B00 PL 1401-Q01

Check and relief valve NT 1401-E00 PL 1401-Q01

Oil cooler NT 1401-AC00 PL 1401-Q01

Air cooler NT 1401-AJ00 -

Definition of safety symbols

This is a SAFETY ALERT SYMBOL.

When you see this symbol on the product, or in the manual,

look for one of the following signal words and be alert to the

potential for personal injury, death or major property damage.

Warns of hazards that WILL cause serious personal injury,

death or major property damage.

Warns of hazards that CAN cause serious personal injury,

death or major property damage.

Warns of hazards that CAN cause personal injury or property

damage.

NOTICE

Indicates special instructions which are very important and

must be followed.

DANGER

WARNING

CAUTION

SAFETY CHECK LIST

1. Before operating the compressor, ensure the vessel to

which the compressor is connected is certified to withstand

the pressure and /or vacuum produced.

2. Verify adequately sized relief valves (if necessary, CE approved)

have been fitted to protect the vessel. Do not use solvents

or inflammable products for cleaning the pipelines and the

accessories.

3. Gas/air mixtures which are potentially volatile/explosive must

not be introduced or allowed to be introduced into the compres-

sor.

4. All pressure vessel and piping connected to the compres-

sor must be isolated and in a safe operating condition.

5. Operators should wear ear protection when operating truck

mounted compressors.

6. There are components within the compressor of sufficient

weight to cause injury if mishandled. Use proper lifting

devices as necessary.

7. Where necessary, this equipment should be grounded to

control static electricity.

8. The temperature of the air leaving the compressor is elevat-

ed above ambient due to air compression. Check that the

elevated temperatures do not adversely affect the product

and any material used in design of the system. Attach clear-

ly marked warning signs to warn of potentially hot surfaces

on the compressor, piping and accessories which will burn if

touched.

9. Mounting of the compressor must be correctly engineered

and the compressor must be properly secured. Refer to the

Compressor Mounting section of this manual.

NOTICE :

MOUVEX PACKAGE COMPRESSORS ARE DESIGNED TO PRODUCE

COMPRESSED AIR. NOT TO PUMP GASES, LIQUIDS, POWDERS

OR CONDENSATES THOUGH THE COMPRESSOR. TO DO SO

WOULD VOID THE WARRANTY.

LIFTING POINTS :

The compressor can be picked up from underneath to be trans-

ported.

Those areas are acceptable to support the package.

Compressor and chair support should be favored.

WARNING

IT IS IMPERATIVE TO APPLY THE

TRUCK PARKING BRAKE AND TO

BLOCK THE WHEELS BEFORE ANY

INTERVENTION DUE TO RISKS OF

SERIOUS BODILY INJURIES OR PRO-

PERTY DAMAGE.

Hazardous machinery

can cause severe

personal injury or

property damage.

WARNING

COMPRESSING GASES INTO A VES-

SEL CONTAINING FLAMMABLE OR

EXPLOSIVE GASES OR COMPRESSING

FLAMMABLE OR EXPLOSIVE GASES,

CAN CAUSE PROPERTY DAMAGE,

PERSONAL INJURY OR DEATH.

Hazardous fluids

can cause fire,

serious personal injury

or property damage.

WARNING

FAILURE TO INSTALL ADEQUATELY

SIZED PRESSURE RELIEF VALVE(S)

CAN CAUSE PROPERTY DAMAGE,

PERSONAL INJURY OR DEATH.

Hazardous pressure

can cause

personal injury

or property damage.

CAUTION

COMPRESSOR, PIPING AND ACCES-

SORIES WILL BECOME HOT DURING

OPERATION AND CAN CAUSE SERIOUS

PERSONAL INJURY.

Extreme heat can

cause injury or

property damage.

WARNING

CONTENTS OF THE COMPRESSOR,

TANK, PIPING, AND FILTERS COULD

BE HAZARDOUS TO HEALTH.

TAKE ALL NECESSARY PRECAUTIONS

WHEN PERFORMING COMPRESSOR

SERVICE OR MAINTENANCE.

Hazardous or toxic

fluids can cause

serious injury.

WARNING

THE NOISE EMITTED BY WORKING

MOUVEX SCREW COMPRESSOR

CAN BE HIGHER THAN 80 DBA.

THE END USERS MUST USE, WHEN

NECESSARY THE APPROPRIATE

EAR PROTECTIONS. FAILURE TO

WEAR HEAR PROTECTIONS IN

AREAS WHERE THE NOISE IS

HIGHER THAN 80 DBA CAN LEAD TO

PERMANENT BODY DAMAGE.

A loud noise can

cause permanent

body damage.

3/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

SAFETY DATA

4/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

B600 20R - 30R LS-DDNC

1. OVERALL DIMENSIONS

Poids avec limiteur de couple

Weight with torque limiter :

161 kg

AJauge d’huile / Oil gauge

BFiltre à huile / Oil filter

CVidange / Draining cap

DContrôle pression G1/4” / Pressure control G1/4”

EContrôle T° G1/4” / T° control G1/4”

FPlaque signalétique / Identification plate

GPrise pression huile / Oil pressure plug

HBouchon 3/4” (pour montage jauge d’huile à droite)

3/4” cap for right oil gauge installation

JPrise vitesse G1/4” / Speed control G1/4”

MBouchon magnétique G3/8” / Magnetic plug G3/8”

NIndicateur de colmatage / Restriction indicator

5/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

B600 13R/15L - 19R/22L LS-DDNC

1. OVERALL DIMENSIONS (continued)

Poids avec limiteur de couple

Weight with torque limiter :

191 kg

AJauge d’huile / Oil gauge

BFiltre à huile / Oil filter

CVidange / Draining cap

DContrôle pression G1/4” / Pressure control G1/4”

EContrôle T° G1/4” / T° control G1/4”

FPlaque signalétique / Identification plate

GPrise pression huile / Oil pressure plug

HBouchon 3/4” (pour montage jauge d’huile à droite)

3/4” cap for right oil gauge installation

JPrise vitesse G1/4” / Speed control G1/4”

MBouchon magnétique G3/8” / Magnetic plug G3/8”

NIndicateur de colmatage / Restriction indicator

6/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

MISTRAL 20R - 30R LS-DDNC

1. OVERALL DIMENSIONS (continued)

Poids avec limiteur de couple

Weight with torque limiter :

186 kg

AJauge d’huile / Oil gauge

BFiltre à huile / Oil filter

CVidange / Draining cap

DContrôle pression G1/4” / Pressure control G1/4”

EContrôle T° G1/4” / T° control G1/4”

FPlaque signalétique / Identification plate

GPrise pression huile / Oil pressure plug

HBouchon 3/4” (pour montage jauge d’huile à droite)

3/4” cap for right oil gauge installation

MBouchon magnétique G3/8” / Magnetic plug G3/8”

NIndicateur de colmatage / Restriction indicator

7/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

MISTRAL 13R/15L - 19R/22L LS-DDNC

1. OVERALL DIMENSIONS (continued)

Poids avec limiteur de couple

Weight with torque limiter :

216 kg

AJauge d’huile / Oil gauge

BFiltre à huile / Oil filter

CVidange / Draining cap

DContrôle pression G1/4” / Pressure control G1/4”

EContrôle T° G1/4” / T° control G1/4”

FPlaque signalétique / Identification plate

GPrise pression huile / Oil pressure plug

HBouchon 3/4” (pour montage jauge d’huile à droite)

3/4” cap for right oil gauge installation

MBouchon magnétique G3/8” / Magnetic plug G3/8”

NIndicateur de colmatage / Restriction indicator

8/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

TYPHON II 20R - 30R LS-DDNC

1. OVERALL DIMENSIONS (continued)

Poids avec limiteur de couple

Weight with torque limiter :

214 kg

AJauge d’huile / Oil gauge

BFiltre à huile / Oil filter

CVidange / Draining cap

DContrôle pression G1/4” / Pressure control G1/4”

EContrôle T° G1/4” / T° control G1/4”

FPlaque signalétique / Identification plate

GPrise pression huile / Oil pressure plug

HBouchon 3/4” (pour montage jauge d’huile à droite)

3/4” cap for right oil gauge installation

JPrise vitesse G1/4” / Speed control G1/4”

MBouchon magnétique G3/8” / Magnetic plug G3/8”

NIndicateur de colmatage / Restriction indicator

9/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

TYPHON II 13R/15L - 19R/22L LS-DDNC

1. OVERALL DIMENSIONS (continued)

Poids avec limiteur de couple

Weight with torque limiter :

244 kg

AJauge d’huile / Oil gauge

BFiltre à huile / Oil filter

CVidange / Draining cap

DContrôle pression G1/4” / Pressure control G1/4”

EContrôle T° G1/4” / T° control G1/4”

FPlaque signalétique / Identification plate

GPrise pression huile / Oil pressure plug

HBouchon 3/4” (pour montage jauge d’huile à droite)

3/4” cap for right oil gauge installation

JPrise vitesse G1/4” / Speed control G1/4”

MBouchon magnétique G3/8” / Magnetic plug G3/8”

NIndicateur de colmatage / Restriction indicator

The screws used to hold the compressor in place must be at

least quality 12-9.

During the assembly, watch that no foreign body penetrates

into the compressor. The piping of inhalation and expulsion

must be perfectly clean. Any foreign body risks to damage

seriously the compressor.

The presence of foreign bodies in the compressor inlet

channel is susceptible of leading to serious property

damage or serious injuries.

2.1 Mounting location

The compressor must be installed in a location where it is

easily accessible. In particular, make sure that the oil

filling plug, oil magnetic plugs and the filter are accessible.

The clogging indicator must remain visible to the operator.

Choose a location where the compressor is relatively

protected from gravel projections and road spray as well

as exhaust fumes and engine heat.

The compressor is mounted on the chair at an angle of

4°. If the chair is mounted vertically, it can be used to

adapt to most movements, in other words those which

have a gradient of between 3 and 5° inclusive.

To prevent potential interferences between the package

and the truck accessories (mudflap, tank… ) a minimum

distance of 5 cm between the package and these acces-

sories must be respected.

2.2 Mounting procedure

2.2.1 Package handling procedure

Compressors are packaged and fixed onto a pallet. To

move and install the package for the first time, the pac-

kage should be carried on the pallet.

For maintenance operations, the package should be fas-

tened onto a pallet such that the chair is vertical. The

areas set aside for fastening the package are the com-

pressor and the chair, as shown in the picture below.

2.2.2 Package installation procedure

The compressor package is delivered in option with two

U profiles mounting brackets. The U are not equal, so

that the installer has more room to move when choosing

the vertical position of the package.

We propose the following assembly procedure (without

the U) :

• Bring the compressor package to the side of the truck

using a transpallet or any other suitable equipment.

• Determine the position of the package on the truck as

close as possible to its final position.

• Check the universal joint angles and how parallel the

compressor shaft and the PTO shaft are.

• Mark on the chair the positions of the holes necessary

for assembly.

• Remove the package from the truck.

• Pierce the chair (and the U), deburr and clean. To

make sure that you do not make the part fragile keep a

minimum axle spread distance of 40 mm between 2

holes.

• Bring the package to the truck.

• Mount the package (and the U) on the chassis with a

minimum of 6 fixing points (M14 quality 12-9).

• Remove the pallet and package.

• Check the universal joint angles and how parallel the

compressor shaft and the PTO shaft are.

• Mount the universal joint.

• Perform an operating test on the compressor.

• Check with a manometer the pressure at which the

valve starts to open.

Standard

angle :

4°

Variable angle from PTO to PTO.

3° to 5° are acceptable while chair

is vertical.

Those areas are acceptable to support the package.

Compressor and chair support should be favored.

CAUTION

10/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

2. INSTALLATION

11/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

2. INSTALLATION (continued)

2.3 At succion

It must be installed in such a way that the temperature

of the air sucked in is equivalent to 5°C either side of

ambient temperature.

Any side protection barriers must be removed EACH

time the compressor is used yo allow air to reach the

compressor inlet freely, and move around the cooling cir-

cuit.

The installer must check whether there are such protec-

tive barriers and that they may be manipulated easily by

the driver. It may be desirable to install a system preven-

ting the operation of the PTO if the protection is not

removed, to guarantee that the compressor operates

under satisfactory conditions.

To prevent the filters from clogging prematurely, the air suc-

ked in must be free of smoke and road dust.

A minimum distance of 300 mm must be left free in front

of the filters for their extraction and replacement.

2.4 Safety valve / Check relief

LS-DDNC packages include a safety valve and a check

valve.

See Instructions 1401-E00 MISTRAL - B600 - TYPHON II

CHECK AND RELIEF VALVE.

In the Low Space package case, connexion pressure

drop has to be considered.

The 2 possible setting values are :

• 2 bar (2,3 bar at the compressor)

• 2,3 bar (2,5 bar at the compressor).

The maximum valve setting is 2,3 bar, but it must take

into account the rotating speed range specified in the

compressor instructions.

2.5 Drive

2.5.1 Speed range

In order to comply with the machine directive, the rota-

ting parts of the compressor package (shafts, torque

limiter, universal joint, PTO … ) must not be accessible

to the user or the driver under normal conditions. If

necessary, it is the installer’s responsibility to fit the

necessary protection for preventing any damage to

equipment or physical injury.

MOUVEX cannot be held responsible for consequences

due to the absence of such protection on the final instal-

lation.

The compressor may be operated directly by a universal

joint shaft, with or without a multiplier.

The selection of the drive mode will take into account :

• The compressor mounting configuration

• The driving shaft rotation direction

• The expected power requirement for the given applica-

tion

• The acceptable rpm range for the driving equipment

• The acceptable rpm range for the compressor.

The use of compressors outside of their operating speed

range can lead to property damage or serious injuries.

See Compressor instructions for more details.

IMPORTANT :

Any system providing for a compressor being driven

by a thermal motor must include a system making it

possible to disengage the compressor at startup and

stop of the motor.

In all cases, the drive must make it possible :

• To maintain the compressor rotation speed during load

variations (pressure variations) .

• Not to subject the compressor to sudden or insuffi-

cient starts.

2.5.2 PTO shaft drive

It is mandatory to comply with the following instructions :

• The shaft must be dynamically balanced.

• Its length and its inclination must be as small as pos-

sible, see table

• The drive shaft slides perfectly well during rotation.

• The jaws of the universal joints are parallel.

• Coupling flanges show no eccentricity nor warping of

the bearing surface.

• The angle formed by the universal joint and the drive

shaft must not exceed 15°.

• The compressor shaft must be parallel to that of the

drive shaft.

• The universal joint angle, as defined below, must ne

minimised.

CAUTION

WARNING

THE USE OF A PACKAGE AT PRESSU-

RES GREATER THAN THOSE RECOM-

MENDED MAY CAUSE DAMAGE TO

EQUIPMENT OR SERIOUS INJURY.

Hazardous pressure

can cause

personal injury

or property damage.

LS-DDNC packages incorporate a compressor gradient

of 4° in relation to the horizontal. This gradient allows the

recovery of the most recent PTO angles on current

trucks. If your PTO angle is between 3 and 5° inclusive,

you can install the chair vertically and respect operating

recommendations.

If this is not the case, you should gently slope the chair

to bring the angle between the compressor operating

shaft and the PTO below 1°.

It is possible to equip packages with a multiplier to lesse-

jn the universal joint angle. Refer to the compressor

instructions for further information.

To protect the P.T.O in the event of compressor stalling,

it is necessary to install a torque limiter.

The MOUVEX company shall not be held responsible for

damage resulting from such stalling if this stalling is

caused by wrong manipulation with the compressor or if

no or not the right torque limiter is installed.

The torque limiter will be installed on the compressor

shaft, as illustrated in the photo below.

LS-DDNC packages may be ordered with torque limiters

mounted. Refer to Instructions 1401-B00 TORQUE LIMITER

- MISTRAL B600 TYPHON II.

If the greasing instructions for the universal joint are

not respected, this can lead to ruptures of this uni-

versal joint, as well as property damage and serious

injuries.

2.5.3 Installation of channelling

Channelling connected to the package must be desi-

gned in accordance with regulations to prevent prematu-

re breakdowns on the installation.

In particular, MOUVEX recommends taking the following

precautions:

• Channelling must be supported so as to prevent then

from mechanically loading the inlets and outlets on

the compressor package.

• Discharge channelling must have a diameter at least

equal to that of discharge connections on the com-

pressor package.

2.6 Instrumentation

The package is supplied with an inlet filter clogging indicator.

Any use of the compressor package when the indicator

is showing excessive clogging will cause damage to

equipment or physical injury.

Once the filters have been replaced, the clogging indicator

mat be reset to zero merely by rotating its cap.

2.7 Chair modification

The chair must not be modified except the following ope-

rations :

• Fixation holes as described above,

• Using of the fixation lines the most distant (L),

• Shortening allowed by taking care of the dimen-

sions of 5 mm

risk of loss of MOUVEX warranty on the equipment.

5

L

40 mini

6 screws M14 quality 12-9

Compressor

Torque limiter

AUniversal joint angle

0,017 1°

VERY GOOD

0,035 2°

0,052 3°

0,070 4°

0,087 5°

0,105 6°

GOOD

0,125 7°

0,141 8°

0,158 9°

0,176 10°

0,194 11°

LIMIT

VALUES

0,213 12°

0,231 13°

0,249 14°

0,268 15°

_________

A = √H² + W²

L

If H = Zero, A = W / L

If W = Zero, A = H / L

CAUTION

12/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

2. INSTALLATION (continued)

13/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

4.1 Maintenance schedules

See the compressor instructions for the maintenance

programme.

4.2 Air filter replacement procedure

Check weekly the clogging indicator. When it turns red,

replace the filter cartridge.

Before installing a new cartridge, clean the internal part

of the filter housing with a clean damp cloth.

The presence of foreign bodies in the compressor

inlet channel is susceptible of leading to serious

property damage or serious injuries.

4.3 Cartridge replacement procedure

• Untight the 4 latches 4 holding the filter cover 1.

• Remove the filter cover.

• Remove the 2 cartridges (central and security).

• Throw away the old cartridges.

• Clean the area around the cartridge seal with a rag.

• Place the cartridges in the following order :

- Security cartridge 3

- Central cartridge 7

• Replace the filter cover.

• Tight the 4 latches 4.

4.4 Drive train inspection

Periodically check that there is no play in the jaws and

PTO cross pieces, turning the universal joint manually in

one direction then in the other direction.

4.5 Check and relief valve inspection

See Instructions 1401-E00 MISTRAL - B600 - TYPHON II

CHECK AND RELIEF VALVE.

CAUTION

4. MAINTENANCE

It is imperative to hold the hose in order to avoid whipping

during pressurization.

The operator should remain nearby the equipment throughout

the use to ensure the proper functioning of the system.

WARNING: SEVERE PERSONAL INJURY OR PROPERTY

DAMAGE CAN CAUSE FROM WHIPPING HOSES.

3. USE

14/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

WƌŽďůĞŵ WŽƐƐŝďůĞŽƌŝŐŝŶ WŽƐƐŝďůĞƐŽůƵƚŝŽŶ

dŽŽŵƵĐŚƉƌĞƐƐƵƌĞĚƌŽƉ͘ dŽĐŚĞĐŬƉŝƉĞƐĚŝĂŵĞƚĞƌ͘

ZĞůŝĞĨǀĂůǀĞĚĂŵĂŐĞĚ͘ dŽĐŚĞĐŬƚŚĞŽƉĞŶŝŶŐƉŽŝŶƚ͘

EŽƌĞƚƵƌŶǀĂůǀĞĚĂŵĂŐĞĚ͘ dŽĐŚĞĐŬƚŚĞƉƌŽƉĞƌŽƉĞƌĂƚŝŶŐŽĨƚŚĞEŽƌĞƚƵƌŶǀĂůǀĞ͘

tƌŽŶŐŽŵƉƌĞƐƐŽƌƐƉĞĞĚ͘ dŽĂĚũƵƐƚƚŚĞƐƉĞĞĚďǇƚĂŬŝŶŐĐĂƌĞŽĨƚŚĞƌĂŶŐĞĂůůŽǁĞĚ͘

ZĞůŝĞĨǀĂůǀĞĚĂŵĂŐĞĚ͘ dŽĐŚĞĐŬƚŚĞŽƉĞŶŝŶŐƉŽŝŶƚ͘

ŝƌĨŝůƚĞƌĐůŽŐŐĞĚ͘ dŽĐůĞĂŶƚŚĞĐĂƌƚƌŝĚŐĞŽƌƚŽƌĞƉůĂĐĞŝƚ͘

ŝƌƉƌĞƐƐƵƌĞƚŽŽŵƵĐŚŚŝŐŚ͘ dŽƐĞĞƉƌŽďůĞŵƐϭ͘ͬϮ͘

KƵƚƐŝĚĞƚĞŵƉĞƌĂƚƵƌĞƚŽŽŵƵĐŚŚŝŐŚ͘ dŽƌĞƐƉĞĐƚƚŚĞŵĂǆŝŵƵŵĞǆƚĞƌŶĂůƚĞŵƉĞƌĂƚƵƌĞĂůůŽǁĞĚ͘

>ĂĐŬŽĨŽŝů͘ dŽĐŚĞĐŬƚŚĞŽŝůůĞǀĞů͘

ŽŵƉƌĞƐƐŽƌƐƉĞĞĚƚŽŽŵƵĐŚůŽǁ͘ dŽĂĚũƵƐƚƚŚĞƐƉĞĞĚďǇƚĂŬŝŶŐĐĂƌĞŽĨƚŚĞƌĂŶŐĞĂůůŽǁĞĚ͘

ŝƌĨŝůƚĞƌĐůŽŐŐĞĚ͘ dŽĐůĞĂŶƚŚĞĐĂƌƚƌŝĚŐĞŽƌƚŽƌĞƉůĂĐĞŝƚ͘

ŝƌŝŶůĞƚŚŽƐĞĨŽůĚĞĚ͘ dŽĐŚĞĐŬƚŚĞĂŝƌŝŶůĞƚŚŽƐĞ͘

dŽƌƋƵĞůŝŵŝƚĞƌĚĂŵĂŐĞĚ͘ dŽƌĞƉůĂĐĞƚŚĞƚŽƌƋƵĞůŝŵŝƚĞƌ͘

dƌĂŶƐŵŝƐƐŝŽŶĚĂŵĂŐĞĚ͘ dŽĐŽŶƐƵůƚǇŽƵƌ^ĞƌǀŝĐĞƉŽŝŶƚ͘

^ĐƌĞǁŽŵƉƌĞƐƐŽƌĚĂŵĂŐĞĚ͘ dŽĐŽŶƐƵůƚǇŽƵƌ^ĞƌǀŝĐĞƉŽŝŶƚ͘

tƌŽŶŐŵŽƚŽƌͬƚƌĂŶƐŵŝƐƐŝŽŶŵĂŶĂŐĞŵĞŶƚ͘ dŽĐŽŶƐƵůƚǇŽƵƌdƌƵĐŬĚĞĂůĞƌ͘

KŝůƚŽŽŵƵĐŚǀŝƐĐŽƵƐ͘ dŽďĞŝŶĐŽŵƉůŝĂŶĐĞǁŝƚŚƚŚĞDKhsy/ŶƐƚƌƵĐƚŝŽŶƐ͘

dŽŽŵƵĐŚŽŝů͘ dŽĐŚĞĐŬƚŚĞŽŝůůĞǀĞů͘

KŝůďƌĞĂƚŚĞƌĐůŽŐŐĞĚ͘ dŽĐůĞĂŶƚŚĞŽŝůďƌĞĂƚŚĞƌ͘

tƌŽŶŐŵŽƚŽƌƐƉĞĞĚ͘ dŽŝŶĐƌĞĂƐĞƚŚĞƐƉĞĞĚďǇƚĂŬŝŶŐĐĂƌĞŽĨƚŚĞƌĂŶŐĞĂůůŽǁĞĚ͘

dƌĂŶƐŵŝƐƐŝŽŶĚĂŵĂŐĞĚ͘ dŽĐŚĞĐŬƚŚĞĚƌŝǀŝŶŐƐŚĂĨƚ͘

>ĂĐŬŽĨƌŝŐŝĚŝƚǇŽĨƚŚĞĐŚĂƐƐŝƐ͘ dŽďĞŝŶĐŽŵƉůŝĂŶĐĞǁŝƚŚƚŚĞdƌƵĐŬDĂŶƵĨĂĐƚƵƌĞƌ/ŶƐƚƌƵĐƚŝŽŶƐ͘

ϴ͘sŝďƌĂƚŝŽŶƐ

ϰ͘/ŶůĞƚƉƌĞƐƐƵƌĞĚƌŽƉ

хϳϱŵďĂƌ

;ĐůŽŐŐŝŶŐŝŶĚŝĐĂƚŽƌƌĞĚͿ

ϭ͘WƌĞƐƐƵƌĞŝƐƐƵĞ

Ϯ͘&ůŽǁƌĂƚĞŝƐƐƵĞ

ϯ͘ďŶŽƌŵĂůŚŝŐŚ

ƚĞŵƉĞƌĂƚƵƌĞ

ϱ͘ŽŵƉƌĞƐƐŽƌ

ĚŽĞƐŶ͛ƚŽƉĞƌĂƚĞ

ϲ͘dŽƌƋƵĞůŝŵŝƚĞƌĚĂŵĂŐĞĚ

ϳ͘KŝůůĞĂŬ

5. TROUBLESHOOTING

CAUTION :

OBSERVE ALL SAFETY WARNINGS CONTAINED IN THIS MANUAL.

15/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

The compressor must be scrapped in compliance with the

regulations in force.

During this operation, particular care must be paid to the drai-

nage stages of the compressor.

8. SCRAPPING

6. WARRANTY

6.1 Warranty claims

The following part are considered as wear part :

• Inlet filter cartridge

• Compressor oil

No failure connected with wear part damage will be

accepted under warranty conditions.

The following situations will void warranty for all compo-

nents of the package :

• Tampering with the setting of the relief valve.

• Presence of foreign body inside the compressor body.

• Traces of damage representative of abnormal use of

the package.

• Use of non genuine parts.

• If the compressor is repaired by a repairer who is not

a MOUVEX-approved repairer.

• Construction of the package not validated by our

Design Office.

• Use of an oil other than BSC for a 13R/15L and

19R/22L compressor.

Before returning your equipment to the factory, you must

first obtain an Equipment return approval (RMA) from

our After Sales Department.

A Compressors form information shall be filled by the

installer or distributor and send to MOUVEX in order to

claim for a warranty.

6.2 24-months warranty extension with BSC3

oil

The 24-months warranty extension with BSC3 oil option

increases the warranty for the screw compressor to 60

months :

• Europe zone only,

• Only concerns the bare shaft compressor with or

without multiplier, excluding packages and accessories

(air filter, torque limiter, check relief valve...),

• Use of BSC3 oil (provide invoices),

• Conditions identical to the current standard warranty.

7.1 Compressor

The equipment must be systematically stored in an area shel-

tered from bad weather.

The equipment must bear its original protective components

until it is installed in its final application.

If installation is interrupted, put back in place the original pro-

tective components or equivalent components.

7.2 BSC oil

In its unopened original container in a dry, frost-free and

light-free place.

The maximum shelf life is approx. 60 months.

7. STORAGE CONDITIONS

16/16

NT 1401-W00 04 23 Direct drive package LS-DDNC e

9. COMPRESSORS FORM INFORMATION

Before any material return, it is required to get an authorization from MOUVEX.

COMPRESSORS FORM

INFORMATION

After Sales Department

Z.I. La Plaine des Isles - 2 rue des Caillottes - 89000 AUXERRE - FRANCE



+33 3 86 49 87 25 - [email protected]

In order to treat correctly the warranty claims, please first complete this information form.

Thanks to return us this completed document by email as soon as possible.

NAME, ADRESS AND PHONE NUMBER OF THE CUSTOMER

Material purchased by :

...................................................................

Material mounted by :

..................................................................

Material used by :

.................................................................

( Person to contact for technical information :

.................................................................

 ............................................................

EQUIPMENT CONCERNED

Screw compressor Vane compressor Type : ....................................................................................

Delivery date : ....................................................... Starting-up date : .......................................................................................

Serial N° : ............................................................. Running time estimation (hours) : ...............................................................

Have you already replaced the equipment by a new one ? Yes No ( If yes, indicate its serial N° : ....................

TYPE OF INSTALLATION

Direct PTO drive

Belt drive system

Torque limiter (value) : ...........................................

Pressure relief valve setting (value) : .......................

Package DDNC Package DDIC

Other (electric, diesel or hydraulic motor)

( Brief description :

(please join a drawing or pictures of the installation)

...................................................................................................

OPERATING PARAMETERS

( Compressor’s speed : .................................................. rpm

( Operating pressure : ..................................................... bar

( Motor speed at the time or the incident : ...................... rpm

( PTO ratio : ...........................................................................

( Product transfered : ............................................................

SUCTION CONDITIONS

Air connection on truck chimney

Direct air connection

Flexible pipe between filter and compressor

Stainless steel pipe between filter and compressor

Filter type : ..................................................................

DESCRIPTION OF THE MATTER

Leakage Insufficient flow Insufficient pressure

Blocking Noise / vibration Other : ..........................................................................................

.................................................................................................................................................................................................................

IN CASE OR RETURN OF MATERIAL TO OUR FACTORY, PLEASE REQUEST IMPERATIVELY BEFORE SENDING

THE MATERIAL RETURN AUTHORIZATION (RMA) WHICH WILL BE PROVIDED TO YOU BY MOUVEX AFTER SALES DEPARTMENT.

ƌĞǀ͘ϭϬͬϬϲͬϮϬϮϬ

Mouvex 1401-W00 Direct Drive Package LS-DDNC Installation Operation Manual

Mouvex 1401-W00 Direct Drive Package LS-DDNC Installation Operation Manual

dans d''autres langues

Documents connexes

Autres documents