CONCORD Eye-Q Go Wireless Manuel utilisateur

ENGLISH ..................................................................................................1

FRANÇAIS ..............................................................................................23

DEUTSCH................................................................................................45

ITALIANO ................................................................................................67

ESPAÑOL................................................................................................89

PORTUGUÊS ..........................................................................................111

CONTENTS

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 23

Congratulations on the purchase of your new

camera. Your camera has been carefully

engineered and manufactured to give you

dependable operation. Read this manual

before operating the camera to become more

familiar with it and obtain the performance

that will bring you continued enjoyment for

many years.

This manual has been written and formatted

with such depth and detail so you can

maximize the features of your camera, yet

easily follow the instructions.

1

CONGRATULATIONS

ENGLISH

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 1

FCC INFORMATION

FCC WARNING: This equipment meets the limits for a class B digital device,

pursuant to Part 15 of FCC rules. Only the cable supplied with the camera should

be used. Operation with other cables is likely to result in interference to radio

and TV reception and could void the user’s authorization to operate this

equipment. This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that

may cause undesired operation.

Tested To Comply

With FCC Standards

for HOME OR OFFICE USE

Changes or modifications not expressly approved by the manufacturer may void

the user’s authority to operate this equipment.

USER INFORMATION

NOTE: This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment on and off, the user is

encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or a qualified technician for help.

2

IMPORTANT INFORMATION

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 2

Be sure to observe the following precautions when using the camera:

•Do not take pictures or use the Internal LCD Display when

operating a vehicle or while walking.

•Do not open the case of the camera or attempt your own repairs.

Always leave service to authorized repair facilities.

•Keep the camera away from water and other liquids, and never let

it get wet. Never use when it is raining or snowing.

•Should foreign matter or water get into the unit, immediately turn

the power off and contact your local authorized service center.

•Physical damage and malfunction of this unit can cause the image

data stored in its memory to be deleted. Be sure to always keep

backup copies of data by transferring them to a personal

computer.

•Under an environment with electrostatic discharge, the camera

may malfunction and require the user to reset the camera.

•Do not leave the camera in places subject to extremely high

temperatures, such as a sealed vehicle or in direct sunlight.

•Remove the battery when the camera is not used for long periods

of time.

•Use 3V Lithium Battery (CR123A) only.

•Dispose of the battery in a manner that complies with applicable

laws.

•Do not place the camera in unstable locations where the camera

may fall and be damaged.

•Do not touch or press on the Status LCD Display or lens.

3

PRECAUTIONS

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 3

1. Shutter Button

2. Viewfinder

3. Macro Switch

4. Battery Door

5. Capture/Review Switch

6. Self-timer LED

7. UV Filter and Lens

8. USB Connector Port

4

LOCATION OF CONTROLS

FRONT/TOP

1

2

3

4

5

6

7

8

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 4

LOCATION OF CONTROLS (CONTINUED)

5

9. Status LCD

10. Diopter Adjustment Ring

11. Viewfinder/Internal LCD

Display

12. Up Button

13. Down Button

14. Lug for Neck/Wrist Strap

15. ON/OFF/Select Button

16. Self-timer/Delete Button

BACK

A. Battery Indicator

B. Macro Focus Indicator

C. Self-timer Indicator

D. Pictures Remaining Indicator

DISPLAY

10

13

14

11

12

15

16

C

D

9

A

B

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 5

LOADING THE BATTERY

Before taking pictures, a fresh 3V (CR123A) Lithium

battery must be inserted into the unit.

1. Using your thumb, open the battery compartment

by pressing down on the battery door and

sliding it outwards as indicated by the arrow.

2. Insert a 3V (CR123A) Lithium battery. Make sure

to observe the polarity (+/–) as indicated in the

figure.

3. Close the battery compartment.

The camera has a battery indicator that shows the current battery level,

regardless of the mode the camera is in.

6

GETTING STARTED

BATTERY PRECAUTIONS

Follow these precautions when using a battery in this device:

1. Use only the size and type specified.

2. Be sure to follow the correct polarity when installing the battery. A

reversed battery may cause damage to the device.

3. If the device is not to be used for a long period of time, remove the

battery to prevent damage or injury from battery leakage.

FULL

Battery has full

power and is ready

to use.

LOW

Battery has low

power and will

need to be replaced

soon.

When battery is low, discontinue use and replace the battery.

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 6

GETTING STARTED (CONTINUED)

7

TURNING THE CAMERA ON AND OFF

•To turn the camera on, press and

hold down the ON/OFF button ( )

until the Status LCD turns on.

•To turn your camera off, press and

hold down the ON/OFF button ( );

the Status LCD screen will turn

blank, indicating the unit has

powered off.

AUTO POWER OFF

In order to extend the battery life, your camera is equipped with an

auto-shut off circuitry that will automatically shut off the power when

the camera is left unattended or untouched for more than 30

seconds.

I

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 7

TAKING PICTURES

8

1. Turn your camera on ( )

and make sure the review

switch is in CAPTURE mode.

( )

The review switch should be in

the position furthest away from

the shutter button.

2. While looking into the

viewfinder, press the SHUTTER

BUTTON until the LED in the

viewfinder stops blinking and

you hear the camera beep.

The PICTURE COUNTER will

subtract one from the total

number of pictures available.

IMPORTANT: Hold the camera steady until you hear the camera

beep and the LED stops blinking, which indicates that the picture

has been taken.

1

2

1

2

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 8

TAKING PICTURES (CONTINUED)

9

1. Turn your camera on ( ) and

make sure the review switch is in

CAPTURE mode. ( )

The review switch should be in the

position furthest away from the

shutter button.

2. Press the SELF-TIMER button.

The Self-timer indicator ( ) will

appear on the back Status LCD.

Press the SHUTTER BUTTON to

start the self-timer.

3. The LED on the front of the

camera will blink every second

for ten seconds before picture is

taken. After taking the picture,

the camera will then reset itself

to normal CAPTURE mode.

USING THE SELF-TIMER

1

2

1

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 9

MACRO FUNCTION

10

USING THE MACRO FUNCTION

Your camera has been equipped with a Macro function. This enables

you to take pictures of subjects at close range (30 – 60 cm/12 – 24 in)

while still maintaining focus. This feature is particularly useful when

taking pictures of small objects.

ATTENTION: After taking a picture in macro focus mode, you must

manually reset the switch to normal picture taking mode ( ).

1. Turn your camera on ( ) and

make sure the review switch is in

CAPTURE mode. ( )

The review switch should be in the

position furthest away from the

shutter button.

2. Slide the MACRO switch to the

macro position. The Macro

indicator ( ) will appear on the

back Status LCD. Make sure the

subject is within the macro focus

range.

Press the SHUTTER BUTTON to

take the picture.

2

1

2

1

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 10

REVIEWING PICTURES

11

1. Turn the unit on and slide the

review switch towards the shutter

button. This will activate the

Internal LCD Display.

REVIEWING PICTURES

Your camera features an Internal LCD Display, that enables you to

review your images instantly.

For added convenience, your

camera is equipped with a

diopter (Viewfinder Sharpness)

adjustment ring.

Look though the viewfinder, if the image you see appears blurred,

rotate the Diopter Adjustment Ring left or right until the image is

focused to your satisfaction. This adjustment has to be done only

once, however, if another person uses your camera, they may need

to readjust it to their vision. You will then have to readjust the

viewfinder to your preferred setting once again.

2. While looking into the viewfinder,

use the UP/DOWN buttons to scroll

through the pictures. The picture

number will be displayed on the

back Status LCD.

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 11

12

DELETING PICTURES

1. Repeat the "Reviewing

Pictures", steps 1 and 2. Once

you have found the picture you

want to delete, press the

DELETE button.

2. The Delete menu will appear.

Highlight the "Delete One"

option using the UP/DOWN

buttons. (Your desired selection

will be highlighted in black).

Confirm your selection by

pressing the SELECT button.

3. A confirmation screen will appear.

Using the UP/DOWN buttons, select

"Yes" to proceed, or "No" to return

to the REVIEW mode. (Your desired

selection will be highlighted in

black). Confirm your selection by

pressing the SELECT button.

4. Once the picture is deleted,

the above screen will be

displayed. The camera will then

return to REVIEW mode. Repeat

the process if you wish to

delete more individual pictures.

DELETING INDIVIDUAL PICTURES FROM MEMORY

Delete One

Are You Sure?

Yes

No

One Picture

Deleted

Delete One

Delete All

Cancel

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 12

13

DELETING PICTURES

1. While in REVIEW mode, press

the DELETE button.

2. The Delete menu will appear.

Highlight the "Delete All" option

using the UP/DOWN buttons. (Your

desired selection will be highlighted

in black). Confirm your selection by

pressing the SELECT button.

3. A confirmation screen will

appear. Using the UP/DOWN

buttons, select "Yes" to proceed,

or "No" to return to the REVIEW

mode. (Your desired selection will

be highlighted in black). Confirm

your selection by pressing the

SELECT button.

4. Once all pictures are deleted,

the above screen will be

displayed and a blank screen

will appear on the Internal LCD

Display.

DELETING ALL PICTURES FROM MEMORY

All Picture

Deleted

Delete One

Delete All

Cancel

Delete All

Are You Sure?

Yes

No

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 13

INSTALLING YOUR CAMERA'S SOFTWARE:

You must first install the camera software before you can download

pictures from your camera into your PC.

WARNING: DO NOT CONNECT THE CAMERA TO YOUR COMPUTER

UNTIL YOU HAVE COMPLETED THE SOFTWARE INSTALLATION.

1. Insert the included CD-ROM into your computer’s CD-ROM Drive.

2. The installation screen will appear. Follow the software installation

instructions on your screen to install the software.

If your computer has the CD-ROM automatic installation disabled,

click on START, select MY COMPUTER and locate the CD-ROM

Drive. Then, double-click on the CD-ROM Drive icon to show its

contents, double-click on the file named SETUP.EXE and follow the

instructions on your screen.

CONNECTING YOUR CAMERA TO YOUR PC AND DOWNLOADING

PICTURES

Before you can use your camera to download images to your

computer, you need to install the camera's software on your

computer (see "Installing Your Camera's Software" section above).

Once you have taken a few pictures with your camera, or as soon as

the camera's memory is full, you can download the pictures into your

computer to print, e-mail, store or to manipulate them in creative

and fun ways, utilizing the bonus imaging and video software that

accompanies your camera.

14

COMPUTER CONNECTION

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 14

You must first install the software before you connect the camera to

your PC. After the software installation is complete, follow these

simple steps:

1. Using your fingernail,

open the USB port

door to access your

camera's USB cable

connector. ( )

2. Plug the square end

of the (supplied) USB

cable to the USB

connector in your

camera. ( )

3. Plug the rectangular

end of the USB cable into your PC's USB port.

(please refer to your PC's documentation if you do not know

where the USB port is.)

4. Turn your camera's power on.

5. Launch ArcSoft PhotoImpression

™

software by clicking on

Start–Programs–ArcSoft Camera Suite and choose

PhotoImpression

™

from the application list on your screen.

15

DOWNLOADING PICTURES

1

2

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 15

6. Follow these steps to retrieve your

pictures from the camera:

A- Click on the GET PHOTOS icon.

B- Click on the CAMERA/ SCANNER

button.

C- Click on the drop-down list under

SELECT SOURCE and choose EYE-Q

Go!.

D- Click on the CAMERA / SCANNER

button. A second window will appear

showing the contents (pictures) of your camera’s memory, and options on

how to handle them.

E- Select the picture(s) you want to retrieve by pressing the Ctrl key on your

keyboard and clicking once on each thumbnail.

F- Click on RETRIEVE.

G- The pictures just retrieved will be placed as thumbnails on the bottom of

your application window. To open them, just double-click on the thumbnail.

H- While the window described in Step D is displayed, you have the option to

delete pictures from your cameras memory. To DELETE pictures from your

camera, either select the photos you want to delete and click on the

DELETE button; or, click DELETE ALL to delete all the pictures stored on

the camera’s memory.

You are now ready to print, store, or further enhance/manipulate your pictures.

Refer to ArcSoft’s Software Guide for a tutorial on all features Photo Impression

offers.

NOTE: Downloading the pictures does not automatically erase the pictures from

your camera's memory! (If the camera’s memory is full, now it would be a good

time to clear the memory by erasing some or all pictures.) For instructions on

how to erase images, refer to the section on DELETING PICTURES or refer to

Step “H” above.

16

DOWNLOADING PICTURES (CONTINUED)

NOTE: Before deleting pictures from the window described in Step D, be sure

to save them in your computer. Once you delete photos from the camera, you

will not be able to recover them.

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 16

Your digital camera has the ability to capture live streaming video by

using the ArcSoft VideoImpression

™

software. To edit, manipulate or

create video clips using all the features that VideoImpression

™

offers,

follow these simple steps:

1. Follow steps 1 – 4 from the section

DOWNLOADING PICTURES.

2. Launch ArcSoft VideoImpression

™

software by clicking on

Start–Programs–ArcSoft Camera

Suite and choose VideoImpression

™

from the application list on your

screen.

3. Click on the NEW icon

4. Click on the CAPTURE icon.

5. Click on the LIVE icon to view live video if the video is not

already being displayed.

TO RECORD A VIDEO CLIP:

1. Follow steps 1 – 4 above.

2. Click on the RECORD Icon. To stop recording, press the Esc button

on your keyboard or click the PAUSE icon on your screen.

To save your video, simply click on the SAVE icon and follow the on-

screen instructions.

17

VIDEO SOFTWARE

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 17

When you install your camera’s Software Suite, a custom VFW (Video

for Windows

™

) Driver is also installed, which allows you to use the

Eye-Q Go!

™

as a web cam.

1. Follow steps 1 – 4 from the section DOWNLOADING PICTURES.

2. Launch Microsoft

®

NetMeeting

™

software.

3. A new window will appear. Choose Eye-Q Go!

™

from the pull-down

menu.

4. Follow the NetMeeting

™

on-screen instructions, or refer to

NetMeeting’s

™

Help section.

18

WEBCAM CAPABILITIES

IMPORTANT: If you do not have NetMeeting

™

already installed on

your computer, please visit www.microsoft.com for instructions on

how to obtain a copy.

Eye-Q Go Instr.Manual (English) 6/6/02 10:39 am Page 18

La page charge ...

CONCORD Eye-Q Go Wireless Manuel utilisateur

CONCORD Eye-Q Go Wireless Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents