Wacker Neuson GV5600 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
5200003459 01 1011
Operator’s Manual
Portable Generator
GV 5600A
Notice d’Emploi
Générateur
5200003459
Copyright
notice
© Copyright 2011 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the machine. Any
other type of reproduction is prohibited without express written permission from
Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker Neuson Production
Americas LLC represents an infringement of valid copyrights. Violators will be
prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original
instructions
This Operator’s Manual presents the original instructions. The original language of this
Operator’s Manual is American English.
5200003455 01 1011
Foreword
wc_tx001852gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models listed below. These instructions must be followed during
installation and maintenance of the generator (and battery, if equipped).
Machines
covered in
this manual
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
Refer to the separate Repair Manual for detailed instructions on servicing and
repairing the machine.
If you are missing any of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
CALIFORNIA
Proposition
65 Warning
Engine exhaust, some of its constituents, and certain vehicle components, contain
or emit chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Machine Item Number
GV 5600A 0620995
Foreword
4 wc_tx001852gb.fm
Manufacturers
approval
This manual contains references to approved parts, attachments, and modifica-
tions. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following conse-
quences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
wc_bo5200003455_01TOC.fm 5
Table of ContentsGV 5600A
Foreword 3
1 Safety Information 7
1.1 Signal Words Used in this Manual ....................................................... 7
1.2 Machine Description and Intended Use ............................................... 8
1.3 Operating Safety ................................................................................ 10
1.4 Operator Safety while Using Internal Combustion Engines ............... 13
1.5 Service Safety .................................................................................... 14
2 Labels 17
2.1 Label Locations .................................................................................. 17
2.2 Label Meanings .................................................................................. 17
3 Lifting and Transporting 21
4 Operation 22
4.1 Recommended Fuel ........................................................................... 23
4.2 Refueling the Machine ........................................................................ 24
4.3 Determining Power Requirements ..................................................... 25
4.4 Installation .......................................................................................... 26
4.5 Installing the Spark Arrester ............................................................... 26
4.6 Generator Derating ............................................................................. 27
4.7 Grounding the Generator ................................................................... 28
4.8 Operating Heavy Loads ...................................................................... 28
4.9 Use of Extension Cords ...................................................................... 29
4.10 Control Panel ...................................................................................... 30
4.11 Testing the Ground-Fault Interrupt (GFI) ............................................ 31
4.12 Main Circuit Breaker ........................................................................... 31
4.13 Voltage Selector Switch ..................................................................... 32
4.14 Auto Idle Switch .................................................................................. 32
4.15 Before Starting ................................................................................... 33
4.16 Starting ............................................................................................... 34
4.17 Stopping ............................................................................................. 35
4.18 Emergency Shutdown Procedure ....................................................... 35
6 wc_bo5200003455_01TOC.fm
Table of Contents GV 5600A
5 Maintenance 36
5.1 Maintaining the Emission Control System .......................................... 36
5.2 Periodic Maintenance Schedule ......................................................... 36
5.3 Engine Oil ........................................................................................... 37
5.4 Servicing the Air Cleaner .................................................................... 38
5.5 Spark Plug .......................................................................................... 39
5.6 Cleaning the Sediment Cup ................................................................ 40
5.7 Storage ............................................................................................... 41
6 Troubleshooting 42
7 Technical Data 43
7.1 Generator ........................................................................................... 43
7.2 Engine ................................................................................................. 44
8 Emission Control Systems Information and Warranty 45
8.1 Emission Control System Background Information ............................ 45
8.2 Limited Defect Warranty for Exhaust Emission Control System ......... 46
8.3 Limited Defect Warranty for Wacker Neuson Evaporative
Emission Control Systems .................................................................. 46
8.4 California Evaporative Emission Control Warranty Statement ........... 49
8.5 Limited Defect Warranty for Exhaust Emission Control System ......... 50
9 Schematics 52
9.1 Electrical Schematic ........................................................................... 52
9.2 Components ....................................................................................... 53
wc_si000625gb.fm
7
GV 5600A Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000625gb.fm
8
Safety Information GV 5600A
1.2 Machine Description and Intended Use
This machine is a portable electric power source. The Wacker Neuson Portable
Generator consists of a tubular steel frame surrounding a fuel tank, a gasoline
engine, a control panel, and an electric alternator. The control panel includes
controls and receptacles. As the engine runs, the generator converts mechanical
energy into electric power. The operator connects loads to the electric power
receptacles.
This machine is intended for the purpose of supplying electrical power to
connected loads. Refer to the product specifications for the output voltage and
frequency of this generator, and the maximum output power limit of this generator.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Connecting a load that has voltage and frequency requirements that are
incompatible with the generator output
Overloading the generator with a load that draws excessive power during either
continuous running or start-up
Operating the generator in a manner that is inconsistent with all federal, state
and local codes and regulations
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual.
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Fire hazards from improper refueling techniques
Fuel and its fumes
Electric shock and arc flash
Personal injury from improper lifting techniques
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
Generator
vibration
Generators vibrate in normal use. During and after the use of the generator, inspect
the generator as well as extension cords and power supply cords connected to it
for damage from vibration.
wc_si000625gb.fm
9
GV 5600A Safety Information
Have damaged items repaired or replaced as necessary.
Do not use plugs or or cords that show signs of damage such as broken or
cracked insulation or damaged blades.
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons, etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
wc_si000625gb.fm
10
Safety Information GV 5600A
1.3 Operating Safety
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Be aware of the application area.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
DANGER
Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot
see or smell. If you can smell the generator exhaust, you are breathing CO. But
even if you cannot smell the exhaust, you could be breathing CO.
f NEVER use a generator inside homes, garages, crawlspaces, or other partly
enclosed areas. Deadly levels of carbon monoxide can build up in these areas.
Using a fan or opening windows and doors does NOT supply enough fresh air.
f ONLY use a generator outside and far away from windows, doors, and vents.
These openings can pull in generator exhaust.
f Even when you use a generator correctly, CO may leak into the home. ALWAYS
use a battery-powered or battery-backup CO alarm in the home.
f If you start to feel sick, dizzy, or weak after the generator has been running,
move to fresh air RIGHT AWAY. See a doctor. You could have carbon monoxide
poison.
wc_si000625gb.fm
11
GV 5600A Safety Information
Always keep the machine at least one meter (three feet) away from structures,
buildings, and other equipment during use.
Always keep the area immediately surrounding and underneath the machine
clean, neat, and free of debris and combustible materials. Make sure that the
area overhead is clear of debris that could fall onto or into the machine or
exhaust compartment.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
When operating this machine:
Do not operate a machine in need of repair.
Never operate the generator, or tools attached to the generator, with wet hands.
Never enclose or cover the generator when it is in use or when it is hot.
Do not overload the generator. The total amperage of the tools and equipment
attached to the generator must not exceed the load rating of the generator.
Never stand on the machine.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
Installing as
backup power
Special hazards exist when installing this machine as a backup power supply.
Improper connection of generator to a building’s electrical system can allow
electrical current from the generator to backfeed into utility lines. This may result in
electrocution of utility workers, fire, or explosion.
wc_si000625gb.fm
12
Safety Information GV 5600A
If connected to a building’s electrical system, the generator must meet the power,
voltage, and frequency requirements of the equipment in the building. Differences
in power, voltage, and frequency requirements may exist and improper connection
may lead to equipment damage, fire, and personal injury or death.
Transporting
and installing
the machine
Never allow untrained personnel to operate or service the generator. The
generator set should be set up by a certified electrician.
Do not stand under the machine while it is being hoisted or moved.
Do not attach equipment to the machine when it is suspended.
Always transport the generator in an upright position.
Always position and operate the generator on a firm, noncombustible, level
surface.
Always make certain the machine is well-grounded and securely fastened to a
good earthen ground per national and local regulations.
Always remove all tools, cords, and other loose items from the generator before
starting it.
Generator
vibration
Generators vibrate in normal use. During and after the use of the generator, inspect
the generator as well as extension cords and power supply cords connected to it
for damage from vibration.
Have damaged items repaired or replaced as necessary.
Do not use plugs or or cords that show signs of damage such as broken or
cracked insulation or damaged blades.
=
After use
Store the machine properly when it is not being used. The machine should be
stored in a clean, dry location out of the reach of children.
WARNING
Backfeed from the generator into the public power distribution system can cause
serious injury or death to utility workers!
f Connections to a building’s electrical system must be made by a qualified elec-
trician and comply with all applicable laws and electrical codes.
wc_si000625gb.fm
13
GV 5600A Safety Information
1.4 Operator Safety while Using Internal Combustion Engines
Refueling
safety
When refueling the engine:
Do not smoke.
Do not refuel if the generator is sitting in a truck fitted with a plastic bed liner.
Static electricity can ignite the fuel or fuel vapors.
Do not refuel a hot or running engine.
Do not refuel the engine near an open flame.
When refueling the engine, always:
Refill the fuel tank in a well-ventilated area.
Replace the fuel tank cap after refueling.
Operating
safety
When operating the generator:
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine.
Do not run the machine if fuel leaks are present or the fuel lines are loose.
Do not run the engine near open flames.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
generator away from the spill and wipe the generator dry before starting.
Do not smoke while operating the machine.
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons, etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
f Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
f Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot
see or smell. If you can smell the generator exhaust, you are breathing CO. But
even if you cannot smell the exhaust, you could be breathing CO.
wc_si000625gb.fm
14
Safety Information GV 5600A
1.5 Service Safety
In order for the equipment to operate safely and properly over a long period of time,
periodic maintenance and occasional repairs are necessary. If the generator is
experiencing problems or is being serviced, attach a “DO NOT START” sign to the
control panel to notify other people of its condition.
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow improperly trained people to service or maintain the machine.
Personnel servicing or maintaining the machine must be familiar with the
associated potential risks and hazards.
Precautions
Follow the precautions below when servicing or maintaining the machine.
Read and understand the service procedures before performing any service to the
machine.
All adjustments and repairs must be completed before operation. Do not operate the
machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose clothing
away from the machine’s moving parts.
Reinstall the safety devices and guards after repair and maintenance procedures
are complete.
Do not allow water to accumulate around the base of the machine. If water is
present, move the machine and allow the machine to dry before servicing.
Do not service the machine if your clothing or skin is wet.
Always turn the engine off before servicing the machine. If the engine has electric
start, disconnect the negative terminal on the battery before servicing the machine.
Always let the engine cool before transporting or servicing the machine.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
WARNING
Poorly maintained equipment can malfunction, causing personal injuries or
equipment damage.
f Do not operate a machine in need of repair.
wc_si000625gb.fm
15
GV 5600A Safety Information
When servicing or maintaining the machine:
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in rating
and performance as the original components.
When replacement parts are required for this machine, use only Wacker Neuson
replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
Always keep the fuel lines in good condition and properly connected. Leaking fuel
and fumes are extremely explosive.
Lifting and
transporting
When lifting the machine:
Make sure slings, chains, hooks, ramps, jacks, and other types of lifting devices are
attached securely and have enough weight-bearing capacity to lift or hold the
machine safely. See chapter Technical Data.
Remain aware of the location of other people when lifting the machine.
Make sure the transporting vehicle has sufficient load capacity and platform size to
safely transport the machine. See chapter Technical Data.
To reduce the possibility of injury:
Do not stand under the machine while it is being lifted or moved.
Do not get onto the machine while it is being lifted or moved.
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons, etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or maintaining
this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
wc_si000625gb.fm
16
Safety Information GV 5600A
Notes:
GV 5600A Labels
wc_si000608gb.fm 17
2 Labels
2.1 Label Locations
2.2 Label Meanings
Wacker Neuson machines use international pictorial labels where
needed. These labels are described below.
A
DANGER!
No sparks, flames or burning objects near
machine.
Shut off the engine before refueling.
B
WARNING!
Hot surface
G
H
B
B
F
J
A
ED
C
wc_gr005147
Labels GV 5600A
18 wc_si000608gb.fm
C
Improper connection of generator to a building’s
electrical system can allow electrical current
from the generator to backfeed into utility lines.
This may result in electrocution of utility work-
ers, fire, or explosion. Connections to a build-
ing’s electrical system must be made by a
qualified electrician and comply with all applica-
ble laws and electrical codes.
D
Close main circuit breaker.
CAUTION!
Use only clean, filtered gasoline fuel.
Check the fuel level.
Open the fuel flow valve.
Close the choke.
Turn the engine switch to the ON position.
Pull the rewind starter.
GV 5600A Labels
wc_si000608gb.fm 19
Open the choke.
Open main circuit breaker.
Turn the engine switch to “OFF”.
Close the fuel flow valve.
E
Electrical ground
F
DANGER
Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon mon-
oxide. This is a poison you cannot see or smell.
NEVER use inside a home or garage, EVEN IF
doors and windows are open.
Only use OUTSIDE and far away from win-
dows, doors, and vents.
Labels GV 5600A
20 wc_si000608gb.fm
G
A nameplate listing the model number, item
number, revision number, and serial number is
attached to each unit. Please record the infor-
mation found on this nameplate so it will be
available should the nameplate become lost or
damaged. When ordering parts or requesting
service information, you will always be asked to
specify the model number, item number, revi-
sion number, and serial number of the unit.
H
Important Emissions Information
This equipment meets California EVP emission
regulations for small off-road engines.
J
Choke lever
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106

Wacker Neuson GV5600 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

dans d''autres langues