Snapper 7800829 Le manuel du propriétaire

Marque: Snapper

Modèle: 7800829

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

7800830

Operator's Manual

Mode1 No.

7800829

7800830

7800832

%. ,J

7105514

Rev. B

ThankYou for purchasing this quality=built Snapper mower. We're pleased that you placed your confidence in the

Snapper brand. When operated and maintained according to the instructions in this manual, your Snapper mower

will provide many years of dependable service.

This rnanuam contains safety information to make you aware of the hazards and risks associated with the

machine and how to avoid them. This machine is designed and intended only for finish cutting of established

lawns and is not intended for any other purpose. It is important that you read and understand these instructions

thoroughly before attempting to start or operate this equipment. Save these originam instructions for future ref-

erence.

Date of Purchase

Retailer

Retailer's Phone Number

Equipment

Model Number

Serial Number

Engine

Model Type Code

SNAPPER is a trademark of

Briggs & Stratton Power Products Group, LLC.

Tabmeof Contents

Operation ........................................................................................................ 11

Before Starting ........................................................................................... 11

Starting the Mower ..................................................................................... 12

Propelling the Mower ................................................................................. 12

Stopping the Mower ................................................................................... 13

Handle Height Adjustment ......................................................................... 13

Cutting Height Adjustment ......................................................................... 13

Mulching Operation .................................................................................... 14

Installingthe Discharge Deflector ............................................................... 14

Installingthe Grass Bag ............................................................................. 14

Charging the Battery .................................................................................. 15

Maintenance Reminder .............................................................................. 16

Maintenance ................................................................................................... 17

Maintenance Chart ..................................................................................... 17

Change Engine Oil ..................................................................................... 18

Service Air Filter ......................................................................................... 18

Check Safety interlock System .................................................................. 19

Clean Debris Off Mower ............................................................................. 19

Drive Control Adjustment ........................................................................... 20

Storage Procedure ..................................................................................... 21

Troubleshooting ............................................................................................. 22

It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered tand unless the exhaust

system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order.

Other states or federal jurisdictions may have similar taws.

Contact the original equipment manufacturer, retailer, or

deater to obtain a spark arrester designed for the exhaust

system installed on this engine.

Battery posts, terminals and related accessories contain

lead and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other repro-

ductive harm. Wash hands after handling.

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals known to the

State of California to cause cancer or other reproductive

harm.

Operator Safety

Operating Safety

Power equipment is only as safe as the operator. If it is misused, or

not properly maintained, it can be dangerous! Remember, you are

responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If you are

not sure that the task you are about to perform can be safely done

with the equipment you have chosen, ask a professional: contact your

local authorized dealer.

Read the Manual

The operator's manual contains important safety information you need to

be aware of BEFORE you operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the product's features and

controls, and maintenance information is included to help you get the

most out of your equipment investment.

Be sure to completely read the Safety Rules and Information found on the

following pages. Also completely read the Operation section.

!, iiiiiiiiii¸

Tragic accidents can occur with children. Do not allow them any-

where near the area of operation. Children are often attracted to the

unit and mowing activity. Never assume that children will remain

where you last saw them. If there is a risk that children may enter

the area where you are mowing, have another responsible adult

watch them.

Slope Operation

You could be seriously injured or even killed if you use this unit on

too steep an incline. Using the unit on a slope that is too steep or

where you don't have adequate footing or traction can cause you to

lose control or slip and fall.

You should not operate on inclines with a slope greater than 10

degrees, which is a 3.5 ft (1,5 m) rise over 20.0 ft (6,0 m). Always

mow across slopes, never up and down.

Also note that the surface you are mowing can greatly impact con°

trol. Wet grass or leaves can seriously affect your footing and trac-

tion on a slope.

Ifyou feel unsure about operating the unit on an incline, don't do it.

It's not worth the dsk.

20.0 ft

(6,0m)

3.5 ft

(1,5m)

4 www.snapper.com

Operator Safety

Moving Parts

This equipment has moving parts that can injure you or someone else.

However, if you stand behind the handle properly and follow all the rules in

this book, the unit is safe to operate.

The mower deck has a spinning mower blade that can amputate hands and

feet. Do not allow anyone near the equipment while it is running!

To help you, the operator, use this equipment safely, it is equipped with an

operator present safety system. Do NOT attempt to alter or bypass the sys=

tem. See your dealer immediately if the system does not pass all the safety

interlock system tests found in this manual.

Thrown Objects

This unit has a spinning mower blade. This blade can pick up and

throw debris that could seriously injure a bystander. Be sure to clean

up the area to be mowed BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge

guard (deflector)in place.

Also, do not allow anyone in the area while the unit is running! If

someone does enter the area. shut the unit off immediately unti! they

leave.

Debris Accumulation

Accumulation of grass and debris can result in a fire. Be sure to clean any

accumulation of grass and debris with a brush or compressed air. before

and after operation.

Fuel and Maintenance

Gasoline is extremely flammable. Its vapors are also extremely fiam=

mable and can travel to distant ignition sources. Gasoline must only

be used as a fuel, not as a solvent or cleaner. It should never be

stored any place where its vapors can build up or travel to an ignition

source like a pilot light. Fuel belongs in an approved, plastic, sealed

gas can, or in the tractor fuel tank with the cap securely closed.

Spilled fuel needs to be cleaned up immediately.

Proper maintenance is critical to the safety and performance of your

unit. Be sure to perform the maintenance procedures listed in this

manual, especially periodically testing the safety system.

Operator Safety

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can

cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or

death to the operator or other persons. The owner of the machine must understand these instructions and must allow

only persons who understand these instructions to operate machine. Each person operating the machine must be

of sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity

or judgment.

_ WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon

monoxide, a poisonous gas that cou}d kimlyou in minutes. You

CANNOT see it, smell it, or taste it. Even if you do not smell

exhaust fumes, you could still be exposed to carbon monox-

ide gas. if you start to feel sick, dizzy, or weak while using this

product, shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

* Operate this product ONLY outside far away from windows, doors and

vents to reduce the risk of carbon monoxide gas from accumulating and

potentially being drawn towards occupied spaces.

* Install battery-operated carbon monoxide alarms or plug-in carbon

monoxide alarms with battery back-up according to the manufacturer's

instructions. Smoke alarms cannot detect carbon monoxide gas.

* DO NOT run this product inside homes, garages, basements, crawlspac-

es, sheds, or other padially-enciosed spaces even if using fans or open-

ing doors and windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even after this product

has shut off.

* ALWAYS place this product downwind and point the engine exhaust

away from occupied spaces.

PROTECTION FOR CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children, Children are often attracted to

the machine and the mowing activity. Never assume that

children wilt remain where you last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the operator.

2. DO NOT allow children in yard when machine is operated

and turn machine OFF if anyone enters the area.

3. DO NOT allow pre=teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine.

5. DO NOT putt mower backwards unless absolutely

necessary. LOOK and SEE behind and down for children,

pets and hazards before and white backing.

6. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

SLOPE OPERATmON

1. Slopes are a major factor related to slip and fail acci-

dents, which can result in severe injury. All slopes require

extra caution. If you feel uneasy on a slope, DO NOT mow

it.

2. Mow across slopes, never up=and=down. Exercise

extreme CAUTION when changing directions on slopes.

DO NOT mow steep slopes or other areas where stability or

traction is in doubt. Refer to the Slope Guide at the back of

this manuat.

3. Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

1. Read, understand, and follow instructions and warnings

in this manual and on the mower, engine and attachments.

Know the controls and the proper use of the mower before

starting.

2. Only mature, responsible persons shati operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower=related injuries.

These operators should evatuate their abitity to operate the

mower safely enough to protect themselves and others from

serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel container.

DO NOT remove fuel cap or add fuel with engine running.

Add fuel outdoors onty with engine stopped and cool. Clean

spitled fuel and oit from machine. DO NOT smoke.

5. Check the area to be mowed and remove all objects

such as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by blade or interfere with mowing.

Also note the tocation of holes, stumps, and other possible

hazards.

6. Keep people and pets out of the mowing area.

Immediately, STOP Blade, Stop engine and Stop mower if

anyone enters the area.

7. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

8. Make sure all safety decals are clearly tegibie. Replace if

damaged.

9. Protect yourself when mowing and wear safety glass-

es, tong pants and substantial footwear. DO NOT mow

barefooted or with sandats.

10. Know how to STOP blade and engine quickly in

preparation for emergencies.

11. Use extra care when loading or unloading the machine

into a trailer or truck.

12. Check grass catcher components frequently for signs

of wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or torn spots.

6 www.snapper.com

Operator Safety

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place the contain-

ers on the ground away from the vehicle before filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed

vehicles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOT use a nozzle lock-open device

10. Iffuel is spilled on clothing, change clothing immedi-

ately.

11. DO NOT overfill a fuel tank. Replace fuel cap and tight-

en securely.

1. DO NOT put hands or feet near or under rotating parts.

Keep clear of discharge area while engine is running.

2. STOP engine when crossing gravel drives, walks, or

roads, and under any conditions where thrown objects

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of

alcohol or drugs.

5. After striking a foreign object or if mower vibrates

abnormally, STOP the engine, disconnect and secure spark

plug wire. Inspect the mower for any damage and repair the

damage before starting.

6. DO NOT mow near drop offs, ditches or embankments.

Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches, wash-

outs, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your

footing. Keep a firm hold on the handle and walk, never run.

Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is

running.

10. DO NOT leave the machine with the engine running.

STOP BLADE and STOP ENGINE before leaving the

operators position for any reason.

11. Before cleaning, repairing or inspecting make cer-

tain engine, blade and all moving parts have STOPPED.

Disconnect and secure spark plug wire away from plug to

prevent accidental starting.

12. STOP engine and wait until the blade comes to com-

plete STOP before removing grass bag and/or clearing

grass.

13. DO NOT operate mower without the entire grass

catcher, rear guard, or other safety devices in place and

working. DO NOT point discharge at people, passing cars,

windows or doors.

14. DO NOT discharge material against a wall or

obstruction. Material may ricochet back towards the opera-

tot.

15. Slow down before turning.

16. Watch out for traffic when near or crossing roadways.

17. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poison.

18. Only use accessories approved by the manufacturer.

See manufacturer's instructions for proper operation and

installation of accessories.

MAINTENANCE AND STORAGE

1. DO NOT store mower or fuel container inside where

fumes may reach an open flame, spark or pilot light such

as in a water heater, furnace, clothes dryer or other gas

appliance. Allow engine to cool before storing machine in

an enclosure. Store fuel container out of reach of children in

a well ventilated, unoccupied building.

2. Keep mower and engine free of grass, leaves or excess

grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts and screws

properly tight. Check that all cotter pins are in proper

position.

5. Always provide adequate ventilation when running

engine. Engine exhaust gases contain carbon monoxide, a

deadly poison.

6. Service engine and make adjustments only when engine

_sstopped. Removed spark plug wire from spark plug and

secure wire away from spark plug to prevent accidental

starting.

7. DO NOT change engine governor speed settings or

overspeed engine.

8. Check grass bag assembly frequently for wear or dete-

rioration to avoid thrown objects and exposure to moving

parts. Replace with new bag if loose seams or tears are evi-

dent. Replace slider or bag adapter if broken or cracked.

9. Mower blades are sharp and can cut. Wrap the blades

or wear heavy leather gloves and use CAUTION when han-

dling them.

10. DO NOT test for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

11. Rave machine serviced by an authorized dealer at least

once a year and have the dealer install any new safety

devices.

12. Use only factory authorized replacement parts or like

parts when making repairs.

Operator Safety

Safety and Operation E)ecams

Reading this manual and the safety instructions it con-

tains wifl provide the basic knowledge necessary to

operate this mower safely and effectively. However,

several safety and operation decals have also been

placed on the mower as a reminder of this important

information during operation.

The decals noted below are located on the mower.

The safety warnings and operation instructions they

contain should be carefully read, understood, and folo

lowed. Not following these important warnings and

instructions can result in serious bodily injury or

death.

If any of these decals are lost or damaged, replace

them immediately. Contact your dealer for replacement

decals.

Mower Run

Part No. 71

Mower Start

Part No. 7105280

Mower Stop

Part No. 7104746

.................

Drive Control

Part No. 7104744

Safety Warnings

Part No. 7105217

Battery Charge

(7800830)

Part No. 7103970

Keep Hands and

Feet Away

Part No. 7105261

8 www.snapper.com

E×pianation of Safety Decals

Operator Safety

A_ _ P{E_

_T_E

A. WARNING: Avoid Serious Injury or Death

Read the operator's manual before attempting

to operate the mower.

Mow across slopes, not up or down.

To avoid injury to others, do not mow when

others, especially children, are around.

To reduce the potential for fire. wait at least 2

minutes before refueling.

B. DANGER: Amputation and Thrown Object Hazard.

To avoid serious injury or death, keep hands

_'I_ and feet away from the mower deck at all times

during operation.

To avoid injury from thrown objects, do not

operate the mower unless all mulching, dis-

charge, or bagging components are in their

proper place

C. DANGER: Keep Hands and Feet Away.

Explanation of Operation Decals

710397#

A. Drive Control

* Push drive control forward to propel mower. Push

the drive control further forward to increase ground

speed.

B. Mower Start

1. Squeeze blade control against drive control, and

pull drive control all the way back.

2. A. Push start button to start mower (7800830).

B. Pull starter rope handle to start mower.

C. Mower Run

* Squeeze blade control against drive control.

D. Mower Stop

* Release blade control

* Engine willstop.

E. Battery Charge (7800830)

* Indicates location of battery charge port.

Features and Controls

mMPORTANT

The figures and illustrations in this manuat are provided

for reference only and may differ from your specific model.

Contact your dealer if you have questions.

B°

E°

Cutting Height Adjust Lever (4)

(7800832)

Mulching Cover

Fuel Filler Cap

Cutting Height Adjust lever (1)

(7800829, 7800830)

Starter insert (7800830)

Rope Start Handle

L°

Start Button (7800830)

Maintenance Reminder

(7800829, 7800830)

Drive Control (2)

Blade Control (2)

Grass Bag

Oil Fill Cap and Dipstick

10 www.snapper.com

Before Starting

1. Check the guards, deflectors, grass bag, and coy=

ers to make sure aHare in place and securely tight-

ened.

2. Check the blade control (A, Figure 1) and drive

control (B) to insure they work freely.

Operation

5. Add fuel to the tank:

• Make sure the mower is outside, where fumes

can safely dissipate.

Remove the fuel fill cap (C, Figure 2).

Fill the tank with fuel. Refer to the section entitled

'Fuel Recommendations'. To allow for expansion

of the fuel, do not fill above the bottom of the filler

neck (D).

Reinstall the fuel fill cap.

6. Clean the exterior surfaces of the cutting deck and

engine of any accumulation of spilled fuel, dirt,

grass, oil, etc. Keep the engine air intake screen

and cooling fins clear at aHtimes.

7. Charge the battery. Refer to the section entitled

"Charging the Battery".

Figure 1: Mower controls

3. Check the cutting height. Adjust to the desired

height. Refer to the section entitled 'Cutting Height

Adjustment'.

4. Check the engine oil:

Make sure the mower is on a level surface.

Clean the oil fill area of any debris.

Remove the dipstick (A, Figure 2) and wipe with

a clean cloth.

Insert and tighten the dipstick.

Remove the dipstick and check the oil level It

should be at the top of the full indicator (B} on the

dipstick.

If low, add oil slowly into the engine oil fill. Refer

to the section entitled 'Oil Recommendations'. Do

not overfill. After adding oil, wait one minute and

recheck the oHlevel.

Replace and tighten the dipstick.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service

SF, SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscos-

ity for the engine. Use the chart to select the best vis-

cosity for the outdoor tern perature range expected.

-04 -- _........

J t0

= ............................10

-20

°30

* Below 40°F (4°C) the use of SAE 30 will resuR in

hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause

increased oil consumption. Check oil level more

frequently.

Figure 2: Oil and fuel fill

Fuel Recommendations

Fuemmust meet these requirements:

* Clean, fresh, unleaded gasoline with

* A minimum of 87 octane / 87AKI (90 RON).

* Gasoline with up to 10% ethanol (gasahol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

* CAUTION: DO NOT use unapproved gasoline, such

as E85. Do not mix oHin gasoline or modify the engine

to run on alternative fuels. This will damage the engine

components and void the engine warranty.

The engine on this equipment is certified to operate on

gasoline. The emissions control system for this engine

is EM (Engine Modifications).

High A_titude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane/85 AKI (89 RON) gasoline is acceptaMe.

To remain emissions compliant, high altitude adjust-

ment is required. Operation without this adjustment will

cause decreased performance, increased fuel con-

sumption, and increased emissions.

Operation of the engine at altitudes below 2,500 feet

(762 meters) with the high altitude kit is not recom-

mended.

Starting the Mower

_t_ WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon

monoxide, a poisonous gas that cou}d kH_you in minutes. You

CANNOT see it, smell it, or taste it. Even if you do not smell

exhaust fumes, you could stHI be exposed to carbon monox-

ide gas. ff you start to feel sick, dizzy, or weak while using this

product, shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

* Operate this product ONLY outside far away from windows, doors and

vents to reduce the risk of carbon monoxide gas from accumulating and

potentially being drawn towards occupied spaces.

* Install battery-operated carbon monoxide alarms or plug in carbon

monoxide alarms with battery back-up according to the manufacturer's

instructions. Smoke alarms cannot detect carbon monoxide gas.

* DO NOT run this product inside homes, garages, basements, crawlspac

es, sheds, or other partially-enclosed spaces even if using fans or open-

ing doors and windows for ventilation. Carbon monoxide can quickly

build up inthese spaces and can linger for hours, even after this product

has shut off.

* ALWAYS place this product downwind and point the engine exhaust

away from occupied spaces.

The engine on this mower is equipped with a

ReadyStart ® system, which features a temperature-

controlled automatic choke. It does not have a manual

choke or a primer.

1. Plug the starter insert (A, Figure 3, 7800830} into

the connection slot in the control console.

2. Squeeze the blade control (B} against the drive

control (C}.

3. Pull the drive control all the way back to the neutral

position.

NOTE: The blade control and drive control can be

operated from either side.

4. Pull the rope start handle (D} or push the start but°

ton (E, 7800830) to start the engine.

5. To stop the engine (and blade), release the blade

control.

6. After the engine starts, allow a brief warm-up until

the engine runs smooth before beginning mower

operation.

Figure 3: Starting the mower

PtopeJling the Mower

1. Start the engine.

2. Begin slowly pushing the drive control (A, Figure

4} forward and inward to propel the mower.

Forward speed can be increased by pushing the

drive control further forward and inward.

Figure 4: Propelling the mower

NOTE. The drive control can be operated from either

side.

iMPORTANT: Upon initial use, the drive control may

have to be adjusted. Refer to the section entitled "Drive

Control Adjustment".

12 www.snapper.eom

Stopping the Mower

1. Stop forward motion of the mower by pulling the

drive control aHthe way back.

2. Stop the engine and blade by releasing the blade

control.

3. Remove the starter insert from the control console

(7800830).

To prevent unauthorized starting, always remove the

starter insert when leaving the mower unattended.

Handle Height Adjustment

DO NOT attempt any maintenance, adjustments or service

with engine and blade running, STOP engine and blade,

Remove starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT, Avoid serious burns, allow sufficient time for all com-

ponents to cool,

For greater operator comfort, the height of the mower

handle can be adjusted.

1. Remove the knobs, washers and bolts secunng

the lower handle (A, Figure 5) to the mounting

brackets (B).

2. Align the holes in the handle assembly with one

of the three handle height adjustment holes in the

mounting bracket.

3. Replace the removed hardware, tightening secure-

ly.

Cutting Height Adjustment

DO NOT attempt any maintenance, adjustments or service

with engine and blade running, STOP engine and blade,

Remove starter insert, Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT, Avoid serious burns, allow sufficient time for all com-

ponents to cool,

Pull the cutting height adjust lever (A, Figure 6, 7)

outward, and move to the desired cutting height. The

highest cutting position is Notch 9, and the lowest

cutting position is Notch 1 (Figure 8).

Figure 6: Adjusting cutting height (7800829,

7800830)

Figure 7:Adjusting cutting height (7800832)

Figure 5: Adjusting the handle height

1°25 in

3,18 cm

Figure 8: Cutting height settings (approximate)

Mulching Operation

For best mulching results, cut up to a maximum of 1/3

of grass length and mulch ONLY when grass is dry.

1. Make sure the discharge deflector and grass bag

are removed, and the mulching plug is installed.

2. Set the cutting height adjust to the highest cutting

position.

3. Proceed mowing slowly. Gradually lower the cut-

ting height to obtain the best combination of cut-

ting and mulching performance. Cutting too much

grass in one pass, or cutting wet heavy grass may

cause clumping or plugging of the mower deck.

Installing the Discharge

Installing the Grass Bag

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Remove starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT. Avoid serious burns, allow sufficient time for all com-

ponents to cool.

important: The mulching plug must be removed only

when bagging is desired, and must be replaced as

soon as bagging operations are completed.

1. Raise the rear discharge door (A, Figure 10).

2. Remove the mulching plug (B) from the rear dis-

charge chute.

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Remove starter insert. Disconnect spark plug wire and

secure away from spark ptug. Engine and components are

ROT. Avoid serious burns, allow sufficient time for all com-

ponents to cool.

1. Raise the mulching cover (A, Figure 9}.

2. Install the deflector (B} to the deck under the

mulching cover, making sure that the locking tabs

on the deck (C} go through the slots in the deflec-

tor (B).

3. Lower the mulching cover against the deflector .........

Figure 10: Remow'ng the mulching plug

3. Holding the grass bag handle (A, Figure 11),

install the grass bag onto the mower, making sure

that the grass bag hooks (B) are hooked onto the

rear door pivot rod (C).

Figure 9: Instafling the discharge deflector

14 www.anapper.eom

Charging the Battery

(7800830)

The battery in this mower is sea_ed and maintenance

free, and requires no service other than charging. If the

battery will not accept a charge, bring the mower to an

authorized service center for service.

1. Using the supplied charger, plug the charger con-

nector into the battery charge port (A, Figure 12).

Plug the charger into a wall outlet and charge the

battery for 12-24 hours. (Longer periods will not

damage the battery.)

important: Use only the charger supplied with the

mower to charge the battery. Using a different charger

may damage the battery and/or mower.

2. When charging is complete, unplug and store the

charger.

Figure 11: Instafling the grass bag

Grass Catcher bags are made of woven fabric, and are

subject to deterioration and wear during normat usage.

Check condition of bag before each use. Immediately

replace worn or damaged catcher bagswith onty bags

recommended by the manufacturer. The grass catcher is

optional equipment on some models.

Figure 12: Battery charge port

Maintenance Reminder

(7800829, 7800830)

The maintenance reminder (A, Figure 13) provides

timely reminders of important maintenance items. It

has six display modes:

TotaJ Hours

Displays tota_ hours mower has been operated. This is

the default screen.

Trip Hours

To display:

Press the 'Mode' button (B) until the 'Trip Hours'

screen isdisplayed.

To reset:

Press and hold the 'Reset' button (C) for more

than 3 seconds.

Crock

To display:

Press the 'Mode' button until the 'Clock' screen is

displayed.

To set:

1. Press and hold the 'Mode' button for more than

3 seconds. The hour display will flash.

2. Press the 'Reset' button to set the correct hour.

3. Press the 'Mode' button. The minutes display

will flash.

4. Press the 'Reset' button to set the correct min-

utes.

5. Press and hold the 'Mode' button for more than

3 seconds to save the set time.

Spark Plug

The 'Spark Plug' icon (E) will appear every 50 hours

(total hours) of operation. This indicates it is time to

change the spark plug. Be sure to follow the proce-

dures outlined in this manual.

To reset:

1. Press the 'Mode' button until the 'Spark Plug'

screen is displayed. (The icon will flash.)

2. Press and hold the 'Reset' button for more than

3 seconds.

NOTE. If not reset, the 'Spark Plug' icon will automati o

cally disappear after 3 operating hours.

Air Filter

The 'Air Filter' icon (F) will appear every 50 hours (total

hours) of operation. This indicates it istime to change

the air filter. Be sure to follow the procedures outlined

in this manual.

To reset:

1. Press the 'Mode' button until the 'Air FHter'

screen is displayed. (The icon will flash.)

2. Press and hold the 'Reset' button for more than

3 seconds.

NOTE. If not reset, the 'Air Filter' icon will automatically

disappear after 3 operating hours.

Change oil Spark plug Air filter

® ® ®

Change Oil

The 'Change Oil' icon (D) will appear after the first 5

hours (total hours) of operation, then after every 25

hours of operation thereafter. This indicates it is time

to change the oil Be sure to follow the procedures out-

lined in this manual.

To reset:

1. Press the 'Mode' button until the 'Change Oil'

screen is displayed. (The icon will flash.)

2. Press and hold the 'Reset' button for more than

3 seconds.

NOTE. If not reset, the 'Change Oil' icon will automati o

cally disappear after 3 operating hours.

Figure 13: Maintenance reminder

16 www.snapper.eom

Maintenance

Maintenance Chart

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Remove the starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT. Avoid serious burns, attow sufficient time for all com-

ponents to cool. Wear heavy teather gtoves when handling

or working around cutting blades. Blades are extremely

sharp and can cause severe injury.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain "no charge" emissions control seP

vice, the work must be performed by a factory autho-

rized dealer. See the Emissions Warranty.

Every 8 Hours or Daily ............

Check safety interlock system

Clean debris off mower

Every 25 HoUrS or ArlnuaHy _

Check mower for loose hardware

Lubricate mower

Check mower blade **

Check mower blade stopping time

Check drive belt

Clean battery and cables

* Whichever comes first

_"Check blade more often in regions with sandy soils

or high dust conditions.

-- m

First 5 Hours .................

Change engine oH

Every 8 Hours or Dai_y ............

Check engine oil level

Clean engine air filter and pre-cleaner (if equipped)

Change engine oil

Replace oil filter (if equipped)

Replace air filter

Replace pre-cleaner (if equipped)

'See Dea_er Annually to

Inspect muffler and spark attester (if equipped)

Replace spark plug

Replace fuel filter (if equipped)

Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when

airborne debris is present.

Change Engine Oil Service Air Filter

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Remove starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT. Avoid serious burns, allow sufficient time for all com-

ponents to cool.

1. Drain the fuel tank completely.

2. Remove the dipstick (A, Figure 14}, then turn the

mower on its side. Allow the oil to drain from the oil

fill tube into an appropriate container. Dispose of

used oil property.

3. Place the mower upright, then fill the engine with

engine oil to the 'full' mark on the dipstick. Refer

to the section entitled 'Oil Recommendations'. Do

not overfill

Never start or run the engine with the air cleaner

assembly (if equipped) or the air fi}ter (if equipped)

removed.

NOTE: Do not use pressurized air or solvents to clean

the filter. Pressurized air can damage the filter and

solvents will dissolve the filter.

1. Loosen the fastener (A, Figure 15} that holds the

cover (B}.

2. Open the cover and remove the pre-cleaner (C}

and the filter (D}.

3. To loosen debris, gently tap the filter on a hard sur-

face. If the fi}ter is excessively dirty, replace with a

new filter.

4. Wash the pre-deaner in liquid detergent and

water. Then allow it to thoroughly air dry. Do not oil

the pre-cleaner.

5. Assemble the dry pre-cleaner to the filter with the

lip (E} of the pre-cleaner on the bottom of the fi}ter

pleats.

6. Install the filter.

7. Install the cover tabs (F} into the slots (G}.

8. Close the cover and secure with the fastener.

Figure 14: Draining the engine oil

Figure 15:Air filter and pre-cleaner

18 www.snapper.eom

Maintenance

Check Safety interlock System

1. Start the mower.

2. Release the blade control. The engine must stop

within 3 seconds.

If the engine does not stop within 3 seconds, do not

use the mower. Bring the mower to an authorized

dealer for service.

Clean Debris Off Mower

Washout Port

WARNING

, Use appropriate eye protection.

, Keep people and pets out ofthe area.

, Stay behind the handle whilethe engine is running.

, Do notattempt mowing operations while usingthe

washout port.

, Do notattempt to took under or reach under the mower

deck for any reason while usingthe washout port.

Serious injurycan result.

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Remove starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT. Avoid serious burns, allow sufficient time for all com-

ponents to cool. Wear heavy leather gloves when handling

or working around cutting blades. Blades are extremely

sharp and can cause severe injury.

1. Clean dirt and debris from the top of the mower

deck.

2. Clean any debris buildup on or around the engine.

etc.

While cleaning, check components for wear or dam-

age. Replace worn or damaged components immedi-

ately.

The washout port allows hands-free cleaning of the

underside of the mower deck. To use the washout port:

1. Be sure the grass bag and side discharge deflector

are removed.

2. Set the height of cut to the lowest position.

3. Move the mower to a level, paved surface.

4. Stop the engine.

5. Connect the male end of a standard garden hose

to the washout port connector (A, Figure 16).

6 Turn on the water supply to the garden hose.

7. Start the engine and run until no more debris

emerges from under the mower deck.

8 Stop the engine.

9 Turn off the water supply to the garden hose.

10.Disconnect the garden hose from the washout port

connector.

11.Start the engine and run for 2=3 minutes, to allow

the underside of the mower deck to dry.

Figure 16: Washout port

Drive Control Adjustment

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Remove starter insert. Disconnect spark plug wire and

secure away from spark plug. Engine and components are

ROT. Avoid serious burns, allow sufficient time for all com-

ponents to cool.

The drive control (A, Figure 17) should engage the

transmission when the control is pushed forward, and

should disengage the transmission when pulled all the

way back.

*IMPORTANT: Before attempting to decrease drive

cable tension, perform the following test:

1) With the mower running, push the drive control for-

ward and inward to propel the mower forward.

2) Pull the drive control back to the neutral position

and immediately pull the mower backwards. You

should feel some resistance from the drive wheels.

This is normal.

3) Without engaging the drive system, push the

mower forward, then pull it backwards again. This

time there should be no resistance. If that is the

case, then drive cable adjustment is not required.

However, if resistance is still felt, then adjust the

drive cable.

Figure 17: Drive control

If the transmission does not engage or disengage,

adjustment may be performed as follows:

• If the transmission does not engage, increase drive

cable tension by loosening the jam nut (C, Figure

18} and rotating the turnbuckle (A) counter-clock-

wise one-half turn to move the ferrules (B} out from

the turnbuckle. Tighten the jam nut against the

turnbuckle. Check and repeat as needed.

If the transmission does not disengage, decrease

drive cable tension* by loosening the jam nut and

rotating the turnbuckle one-half turn clockwise to

move the ferrules in toward the turnbuckle. Tighten

the jam nut against the turnbuckle. Check and

repeat as needed.

Figure 18: Adjusting the drive cable

Caution: Incorrect adjustment can cause premature

wear and/or damage to the wheel drive components.

NOTE. Some models do not feature a jam nut.

20 www.snapper.eom

La page charge ...

Snapper 7800829 Le manuel du propriétaire

Marque: Snapper

Modèle: 7800829

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

7800830

Télécharger le PDF

rapport

dans d''autres langues

English: Snapper 7800829 Owner's manual

Snapper 7800829 Le manuel du propriétaire

Ce manuel convient également à

Snapper 7800829 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents