PRODUCT
MODEL
SCOPE OF
APPLICATION
DATE
SHENZHEN HAISEN TECHNOLOGY CO.,LTD
PRODUCT SPECIFICATION
APPROVED APPROVAL
CHECKED
MICROWAVE MOTION SENSOR
2021.1.1
HB001VCR-1A
3
This specification is applicable to describe the function and use of
HB001VCR inductor of Shenzhen Haisen Technology Co.,Ltd
SHENZHEN HAISEN TECHNOLOGY CO.,LTD
address：Building A6,Nanpu Science & Technology Park, Hao'si Shajing,
Bao'an District, Shenzhen,P.R.C.
TEL：+86-755-82598105 Email: [email protected] Net：www.haisensz.com
www.haisensz.com
Technical data
HB001VCR
：
Daylight
threshold Stand-by
period
Stand-by
dimming level
Hold
time
Detection
area
On/off
control
Detection area
Operating voltage
Stand-by power
Hold time
Daylight threshold
Stand-by period
Stand-by dimming level
Microwave frequency
Microwave power
Mounting height
Detection range
Operating temperature
Detection angle
IP rating
Motion detection
Warranty
Control method On/off
0.5W
Operating current 30ma
diameter 10m*4m(Max)
Max. 4m (ceiling mounted)
DC:10.5-15V
150°(Wall mounted) 360°(ceiling mounted)
Others
Note
5 years
Function setting DIP Switch
Input
Output
Sensor
Parameters
0-10V diming
DIP Switch : 10% 20% 30% 50% 100%
MICROWAVE
MOTION SENSOR
5
years
DIP Switch : 50%/100%
DIP Switch :
DIP Switch :5s/30s/1min10min
10Lux/30Lux/50Lux/Disable
Remote control :
DIP Switch :0S/30S/ 20min/+∞
25%/50%/75%/100%
Remote control : 5s/30s/1min/3min/5min10min/20min/30min
Remote control : 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
Remote control : 0s/10s/30s/1min/ 5min/10min/ 30min/ 60min/+∞
Remote control : 10% 20% 30% 50% 100%
-20°C~+60°C
Connection Red 12V+ Black DIM- Yellow DIM+
5.8GHz±75MHz
<0.3mW
IP20
0.5~+1m/s
1. Automatic On/off control with Daylight sensor.
2. DC input
3. 5 year warranty
1. The result is based on 1.65M/60kg medium-size man walking towards with speed 0.8m/s in vacant room; The sensor hanging at 3M height.
2. It may have different performance if the test delivered by different people, with different speed, at different height or in different conditions.
(Unit: mm)
(Unit: mm)
Antenna module Installation hole
Detection Range
Hold Time
Stand-by Dimming level
Stand-by Period
Daylight threshold
Daylight sensor
1 2 3 4 5 6 7 8 9
10±0.3 mm Solder Length
520±10 mm
Remote Receiver
DIM
3
-+
Settings
Stand-by
dimming level
100%
50%
5s
30S
1min
10min
Disable
50lux
30lux
10lux
0S
+
30
20min
S
∞
10%
30%
20%
50%
Switch UP
Switch DOWN
The definition of
low output in
the standby
period.
Detection area
In this area,
movement will be
detected and able
to trigger the
sensor. 100%
detection area is
also known as the
strong sensitvity.
Daylight threshold
Definition of the
ambient brightness;
only when the ambient
brightness is lower
than the preset specific
lux amount, the sensor
will work; when it's
preset as "disable", the
sensor works everytime
it detects motion
regardless the ambient
Hold-time
The period of light
keeping 100%
brightness after
moving objects
leave the
detection area.
brightness.
Stand-by period
The period of light
keeping low output
before it's completely
switched off. When
it's preset as"∞“, the
light always keep at
low output if no
movement in the
detection area and
doesn't turn off.
Well covered Covered
This figure indicates the maximum distance at the highest mounting height with 100% sensitivity.
Detection coverage
Ceiling Mounted
1 2 3 41234
1
2
3
4
Mounting
height
Haisen Technology | 04
With insufficient daylight,
when motion detected,
light ON.
With sufficient daylight,
even when motion
detected, light remains OFF.
After the stand-by
period, light OFF.
After last detection, the light
will be dimmed down to
the stand-by dimming level
(10%,20%,30% or 50%)
after holdtime.
Hold time Stand-by period
3. Function Demo - Dimmable control/Corridor function
Hold time
After the last detection and the
present hold time elapsed, light
OFF.
With insufficient daylight, when
motion detected, light ON.
After people leave the detection
area, light remains 100% brightness
within hold time.
When motion is detected, the
sensor will switch on the light to
100% brighteness.
After the last detection and the
present hold time elapsed, light
OFF.
1. Automatically ON/OFF function:
Light on when detect movement and off after people leave at night. Applications: Corridor, Staircase.
With sufficient daylight, even when
motion detected, light remains OFF.
2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off
after stand-by period
. Applications: Dim places such as
Basement Parking, Underpass.
Haisen Technology | 05
Haisen Technology | 06Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 Fax: +86-755-82598106Email: [email protected] www.haisensz.com
Attention
1. Please read the instructions carefully before using this product and keep it well for all users to
read at any time.
2. The sensor should be installed by qualified electrician and ensure power is off before the
installation.
3. We reserve the right to modify any incorrect text, image and necessary technical parameters.
4. Any unauthorized modification is forbidden, otherwise all guarantees will be immediately
invalid.
DRIPPING WARNING: This product shall not be exposed to dripping or
splashing, and no objects lled with liquids, such as vases, shall be placed
on the product.
VENTILATION WARNING: The normal ventilation of the product shall not be
impeded for intended use.
SAFETY VERIFICATION: This device is made and tested to meet safety
standards of the FCC, requirements and compliance with safety performance
of the U.S. Department of Health and Human Services and also with FDA
Radiation Performance Standards 21 CFR Subchapter.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modications to this equipment
may cause harmful interference unless the modications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or modication is made.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure
condition without restriction.NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
-The device has been evaluated to meet general RF exposure requirement.
-The device can ben used in the portable exposure condition with restiction
Application Environment
- English:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
- French:
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitationestautorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest
susceptible d'encompromettre le fonctionnement.
ThedevicehasbeenevaluatedtomeetgeneralRFexposurerequirement.
Thedevicecanbeusedinportable exposureconditionwithoutrestriction.
le dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.
l'appareil peut être utilisé dans des conditions d'exposition portatif sans restriction
Shenzhen Haisen Technology Co., Ltd., Tel: +86-755-82598105 Fax: +86-755-82598106Email: [email protected] www.haisensz.com Haisen Technology | 07
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
Autres documents
-
WELMAG WMT100-CS Manuel utilisateur
-
Hytronik Photocell Advance HC403VRC-KD/I + SAM5/I Manuel utilisateur
-
Nordlux Lonstrup 71412031 Mounting Instruction
-
Globe Electric 17000213 Manuel utilisateur
-
-
Satco 65-867-4 Mode d'emploi
-
-
-
Robus RRD360MW-01 Manuel utilisateur
-
Enlite EN-BA1 Series Batpac Pro 1500mm 33w Led Batten Microwave Sensor Mode d'emploi
