ELK ELK-6020BR Mode d'emploi

ELK
Marque
ELK
Modèle
ELK-6020BR
Taper
Mode d'emploi

Ce manuel convient également à

ELK-6020 Wireless Slim-Line Door and Window Sensor
Enrolling from ElkRP Software
1. LaunchElkRPandopenthedesiredCustomerAccountle.
2. If no wireless zones currently exist in this M1 you will need to
create a group of 16 wireless zones. In the folders column
right click on Zones (Inputs) and then click New Wireless
Zones. Place a check mark in the box beside the desired
group, then click OK. Repeat if additional wireless groups
arerequired.Allexpandedzonesmustbedenedingroups
of 16. The M1XRFTW wireless must always start at Zone
17 (Group 2) and the last wireless zone CANNOT be higher
than Zone 160 (Group 10).
Note: M1 only allows Zones 17 to 160 to be used for
wireless zones (max. of 144 wireless sensors). If a large
number of wireless zones is expected, avoid conict with
any future Hardwired Zones in the range of zones 17 to 160
by NOT enrolling any Hardwired Zone Expanders (M1XIN)
at data bus addresses below 10.
3. Double click on Wireless - Group _ (the group just added),
thendoubleclickonezoneatatimetodeneaname,type,
and options. Repeat for each wireless zone. It is more time
efcient in ElkRP to program the Zone Denitions (name,
type, and options) before moving to the Wireless Setup for
entering the TXID and Loop number.
4. From the Folders column double click on Wireless Setup to
setup and enroll the wireless sensors.
4a. Click the Transmitters tab, then double click a zone.
4b. Place a check mark in the Enabled box.
4c. Set Supervision type: 0=Non Supervised (Keyfobs),
1=Normal “Burg” Supervision, or 2=Fire Supervision
4d. Skip down to the TXID box and enter the Sensor TXID
from the printed label located on the sensor.
4e. Skip to the LOOP boxandentera2.Loop2denesthe
built-in reed switch.
4f. Click Save. Repeat the entire step 4 for each additional
Wireless Zone and Sensor.
FCC AND IC COMPLIANCE STATEMENT:
This device complies with Part 15 of the FCC Rules and Industry Canada License-Exempt RSS Standards. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter
by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir
le type d’antenne et son gain de sorte que la puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
PO Box 100 3266 US Hwy 70 West
Hildebran, NC 28637
Ph 828-397-4200 Fax 828-397-4415 http://www.elkproducts.com
Front Page
Operational Testing
A two color LED located behind the plastic cover (front & center)
displays feedback of transmission status. This LED is very useful
during installation and troubleshooting. Direct sunlight conditions
canmakeitdifculttoseethisLED.
GREEN blink = Sensor has successfully transmitted a violation
(alarm) transmission to the transceiver and that signal has
been received and acknowledged by the transceiver. The
green blink is not provided for a sensor restore transmission.
RED blink = CAUTION This indicates that sensor was unable
to communicate with the transceiver after multiple repeated
attempts. The most likely problem is that the distance
between the sensor and the transceiver is too great. However,
it is also possible that the transceiver is off-line or powered
off. Try the following troubleshooting steps:
A. Verify that the transceiver is on with its status LED blinking.
B. Walk to another sensor and test (trip) it to see if it can
communicate with the transceiver.
If steps A & B appear to work then the next step would be
to temporarily remove the failed sensor and re-test it at a
closer range with the transceiver. If the sensor successfully
communicates at a closer range then one of two solutions
may be needed:
1. Try to relocate the transceiver at a closer and more central
location to this and all other sensors.
2. Purchase and install an additional “remote” transceiver to
cover the area where this sensor was mounted.
Per UL a complete test of the security system and all zones should
be performed once a week. The zones may be walk tested using
the M1 Keypad Menu 3 - Walktest Area.
Locating Sensor & Mounting
Sensorshouldbemountedtoaclean,at,drysurface.Always
pre-test sensor in its intended location PRIOR to permanent
mounting. NOTE: Avoid metal mounting surfaces whenever
possible since metal surfaces can negatively affect wireless
operation. Observe temperature and humidity specs. Do not use
in high moisture/humidity areas.
1. Remove the baseplates from the sensor and magnet by
insertingthetipofasmallatscrewdriverintheendslot.
2. Enroll the sensor into the control and transceiver.
3. Test the sensor at its intended location prior to mounting.
4. When ready to permanently mount, use the supplied adhesive
padsor#4atheadsheetmetalscrews.Screws are strongly
recommended when using the tamper option. Be sure the align
marks on both backplates face each other and the maximum
gap DOES NOT EXCEED the gap specs.
APPLICATION
The ELK-6020 Wireless Slim-Line Door & Window Sensor is
ideal for use on narrow jamb door and window applications.
It features Elk’s Industry Leading Two-Way Technology with
positive signal acknowledgment, extended range, and long
battery life. It works with Wireless Transceivers and Controls that
accept Elk’s two-way technology; such as, the ELK-M1XRFTWM.
Eachtimethe6020transmitsitsendsauniqueTXIDidentier
and a Loop number.
SPECIFICATIONS:
Frequency: 902 Mhz - 928 Mhz frequency hopping
Tamper: Field installed plunger for front and back detection
Dimensions: .71”W x 3.4”L x .8”D Mag: .57”W x 1.5L x .6D
Maximum Operating Gap of Reed: 3/4”
Operating Temperature: 14° to 104° F (-10° to 40°C)
Relative Humidity: 5-95% Non-Condensing
Battery: 3.6V ER14250 Lithium - See Battery Installation
Unique TXID Code: Over 1 million combinations
Enrolling from M1 Keypad Installer Programming
1. Enter M1 Keypad Installer Programming and navigate to
Menu: 14-Wireless Setup
2. Press right arrow, then scroll up to Sub-Menu: 3:Learn Sel
WirelessTransmtr
3. Press right arrow, then scroll or select a unused/available
WZone (wireless zone).
4. Press right arrow to Lrn (Enroll) a new sensor.
5. Insert the Battery into the sensor as soon as the keypad
displays: Push Transmitter Button. The M1G voice will
speak; “Press Transmitter button for zone xx”.
NOTE: If battery is already installed; remove it, wait 5
seconds, then re-insert.
6. UponsuccessfulenrollmenttheKeypadwillchimeandbriey
display the 6 digit TXID code of the sensor.
If enrollment fails the TXID will not display. If that occurs;
remove the battery, wait 5 seconds, then re-insert. In certain
instances it may be necessary to repeat steps 3 - 6.
7. The Rapid-Enroll feature will auto advance to the next
wireless zone in sequence and wait for the next sensor
enrollment. Simply repeat step 5 for each additional sensor.
8. To end Rapid-Enroll after all wireless zones (sensors) have
been enrolled press the ELK key one time.
9. Set the Loop Number. ELK wireless sensors use Loop 2 for
the built-in reed switch. Since the 6020 only has the single
“reed switch” zone, the default M1 Loop # 0 will recognize
the reed switch WITHOUT the need to change the Loop from
0 to 2. If you wish to view (or change) the Loop #, scroll up
or down to the desired M1 wireless zone and press the left
arrow. The screen will display a 9 digit number (TXID in
decimal) followed by Loop=.
10. Supervision - For wireless Burg sensors the supervision
should be set to 1=Normal “Burg”. This happens to be
the factory default setting for all wireless zones. To view or
change the Supervision value, press the ELK key to locate
Sub-Menu: 2:Xmit Transmitter Opt. Press the right arrow
and scroll to the wireless zone, then press right arrow to
select.
ZONE DEFINITION: After all wireless zones have been enrolled
proceed to Menu: 5 - Zone Denitions to program the name,
zone type, and any desirable options. Printed In USA
L641 Rev A 1/19/2018
CAUTION: Do not reverse the battery polarity!
- +
Figure 2. ELK-6020 Sensor & Backplate
Location of
front and back
Tamper pill.
Mounting
Holes
To use the case/wall tamper option, insert the rubber actuator
(from the hardware bag) into the post near the center of the
backplate. Tamper will auto-enable when sensor is snapped
onto the baseplate. Tamper will now be sent if sensor is op
is opened or removed. Once enabled, tamper can only be
disabled by removing the battery, removing the actuator, and
re-powering the sensor WITHOUT the actuator present.
Alignment
Marks
Maximum
Operating
Gap = 3/4”
3/4”
Figure 1. ELK-6020 Mounting Gap and Alignment
Battery Installation and Replacement
A low Battery trouble will be sent to the Control when the sensor
battery needs to be replaced. Approved 3.6V Lithium Batteries are:
Xeno XL-050F
1. Remove sensor cover by grasping the sides and inserting the
tipofasmallatscrewdriverintheendslot.
2. Remove old battery and WAIT AT LEAST 20 SECONDS
before installing new battery.
3. Observe correct polarity when installing the new battery. Do
not bend or damage the metal battery holder leafs.
4. Trip sensor several times to send an “all good” and clear the
low battery trouble. Test sensor operation with panel.
Limited Warranty
The 6020 Wireless Slim-Line Door & Window Sensor is warranted to
be free from defects and workmanship for a period of 2 years from
date of manufacture. Batteries used with wireless devices are not
warranted. Elk makes no warranty, express or implied, including that
ofmerchantabilityortnessforanyparticularpurposewithregard
to batteries used with wireless devices. Refer to Elk’s website for
full warranty statement and details.
NOTE: ELK PRODUCTS IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
ELK-6020 Wireless Slim-Line Door & Window Sensor FCC ID: TMAELK-6020 IC: 4353A-6020
BATTERY WARNING: Risk of re, explosion and burns. Do
not attempt to recharge or disassemble. Do not incinerate
or expose to heat above 212° F (100° C). Dispose of used
batteries properly. Keep away from children.
5. Attach the sensor and magnet to their baseplates.
Applying the self adhesive mounting tape:
1. Clean all surfaces of any grease, dirt, etc.
2. Hold tape with pink surface towards you. Gently bend at one
corner, then grasp and remove the pink backing.
3. Grasp the remaining clear backing with adhesive facing side
down and align the edges over the back of the sensor.
4. Gently rub down the tape to the sensor back.
5. Grasp and remove the clear backing just prior to mounting.
6. Hold sensor in place for several seconds to allow a strong bond.
It may require up to 24 hrs for tape to reach full bond
.
NOTE: Adhesive tape cannot be used for UL Listed Installations.
  • Page 1 1

ELK ELK-6020BR Mode d'emploi

ELK
Marque
ELK
Modèle
ELK-6020BR
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents